Search Results

Search found 1096 results on 44 pages for '0000'.

Page 9/44 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• USB Flash Drive not Detected on 12.10 x64

  - by Falguni Roy

  My Mediatek usb flash drive is not get detected. The o/p of lsusb falguni@falguni-M61PME-S2P:~$ lsusb Bus 002 Device 002: ID 0e8d:0003 MediaTek Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub and the o/p of usb-devices falguni@falguni-M61PME-S2P:~$ usb-devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:02.1 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub But in 12.04, the o/p of usb-devices was: falguni@falguni-M61PME-S2P:~$ usb-devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:02.1 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=0003 Rev=02.00 S: Manufacturer=MediaTek Inc S: Product=MT6235 C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm It was working fine in 12.04. Now after upgrading to 12.10 the problem started. Where is the problem and how to solve it?

  Read the article

• GPU hung when switching graphic card

  - by Lie Ryan

  I have a laptop (Dell Inspiron N4110) with a switchable graphic. $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Whistler [AMD Radeon HD 6600M Series] (rev ff) Normally, my laptop starts with both graphic cards enabled, which caused the laptop to turn very hot and the fan to become very noisy. I have been using a small script to disable the Radeon card. For some time, I'm quite happy with this arrangement. However, I have been having some issues with the Intel card (IGD), the Intel card often randomly hang when running OpenGL apps; and so I want to give the Radeon card (DIS) another chance. I have never been able to switch to the Radeon card, but recently, I found out that if I do a "delayed switching" (DDIS): # echo "DDIS" > /sys/kernel/debug/vgaswitcheroo/switch root@lieryan-dell-ubuntu:/sys/kernel/debug/vgaswitcheroo# cat switch 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Pwr:0000:01:00.0 then I logoff (i.e. to restart X), the screen switch to pseudo-tty and then it stuck there freezing. At this situation, mouse and keyboard stops working so I can't switch to another ptty. I tried ssh-ing from another computer to salvage logs (dmesg at that point) and whatnot; I found out that when freezing, the active graphic card is the AMD card: -- this is from ssh -- # cat switch 0:IGD: :Off:0000:00:02.0 1:DIS:+:Pwr:0000:01:00.0 but the GPU is apparently hung, looking at dmesg gives: ... [ 1411.649974] vga_switcheroo: client 0 refused switch [ 1411.649985] vga_switcheroo: setting delayed switch to client 1 [ 1423.911759] vga_switcheroo: processing delayed switch to 1 [ 1424.006564] fbcon: Remapping primary device, fb1, to tty 1-63 [ 1424.006799] i915: switched off [ 1424.840351] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1425.718088] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1426.622377] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1427.355683] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id [ 1428.193549] [drm:drm_mode_getfb] *ERROR* invalid framebuffer id ... the invalid framebuffer id error is repeated for many times over ... I were able to successfully recover by switching back to the Intel card and restarting X from ssh; indicating that only the Radeon card has problems switching. System info: $ uname -a Linux lieryan-dell-ubuntu 3.0.0-14-generic #23-Ubuntu SMP Mon Nov 21 20:28:43 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric The laptop also do not have the option to set graphic card at BIOS and the proprietary driver, fglrx, also have never worked; when I installed it through jockey ("Additional Drivers"), glxinfo showed that it still being rendered by Mesa, the /sys/kernel/debug/vgaswitcheroo directory has gone missing, and the driver crashes with a traceback if I use xorg.conf to tell X to use fglrx. Anyone had any idea if it is possible to use this AMD card either with the radeon or the fglrx driver? logs: dmesg

  Read the article

• Why doesn't Ubuntu detect my second hard drive?

  - by user93179

  I am new to Linux and to Ubuntu, I was wondering, I have two hard drives setup in SATA ports (non-raid, at least I don't think they are). I installed ubuntu unto the drives fresh without any previous versions or windows at all. However when I got the Ubuntu 12.04 LTS working, all I see is 1 x 120 gigabyte harddrive. Also, not sure if this is important or not, my hard drives are SSD. My computer specs are Asus P9Z77-V-LK Nvidia Geforce GTX 660 TI Intel i5 3570k 3.4 /proc/partitions shows: major minor #blocks name 8 0 117220824 sda 8 1 117219328 sda1 8 16 117220824 sdb 8 17 96256 sdb1 8 18 108780544 sdb2 8 19 8342528 sdb3 11 0 1048575 sr0 and ls -l /sys/block/ | grep -v /virtual/: lrwxrwxrwx 1 root root 0 Sep 27 17:26 sda - ../devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda lrwxrwxrwx 1 root root 0 Sep 27 17:26 sdb - ../devices/pci0000:00/0000:00:1f.2/host1/target1:0:0/1:0:0:0/block/sdb lrwxrwxrwx 1 root root 0 Sep 27 22:26 sdc - ../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.1/1-1.1:1.0/host6/target6:0:0/6:0:0:0/block/sdc lrwxrwxrwx 1 root root 0 Sep 27 22:04 sr0 - ../devices/pci0000:00/0000:00:1f.2/host3/target3:0:0/3:0:0:0/block/sr0 sudo file -s /dev/sd*: /dev/sda: x86 boot sector; partition 1: ID=0x7, starthead 32, startsector 2048, 234438656 sectors, code offset 0xc0, OEM-ID " ?", Bytes/sector 190, sectors/cluster 124, reserved sectors 191, FATs 6, root entries 185, sectors 64514 (volumes 32 MB) , physical drive 0x7e, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled /dev/sdb2: Linux rev 1.0 ext4 filesystem data, UUID=387761ac-5eba-4d0f-93ba-746a82fb541d (needs journal recovery) (extents) (large files) (huge files) /dev/sdb3: data /dev/sdc: x86 boot sector; partition 1: ID=0xc, active, starthead 0, startsector 8064, 30473088 sectors, code offset 0xc0 /dev/sdc1: x86 boot sector, code offset 0x58, OEM-ID "SYSLINUX", sectors/cluster 64, reserved sectors 944, Media descriptor 0xf8, heads 128, hidden sectors 8064, sectors 30473088 (volumes 32 MB) , FAT (32 bit), sectors/FAT 3720, Backup boot sector 8, serial number 0xf90c12e9, label: "KINGSTON " /dev/sda1: x86 boot sector, code offset 0x52, OEM-ID "NTFS ", sectors/cluster 8, reserved sectors 0, Media descriptor 0xf8, heads 255, hidden sectors 2048, dos 32 MB) , FAT (32 bit), sectors/FAT 749, reserved3 0x800000, serial number 0x35361a2b, unlabeled Any help would be greatly appreciated! Thanks Another thing I noticed is, when i use gparted to locate my drives, it seems that sda1 is my second drive that I am not detecting when I boot up and my ubuntu + FAT Boot files are installed in sdb1

  Read the article

• Why are external domains appearing in my apache logs?

  - by Johan

  I've got several log entries that refer to an external domain - mainly a Russian search engine (http://www.yandex.ru/) How are these appearing in my logs? 82.146.58.53 - - [10/Jun/2010:00:49:11 +0000] "GET http://www.yandex.ru/ HTTP/1.0" 200 8859 "http://www.yandex.ru/" "Opera/9.80 (Windows NT 5.1; U; ru) Presto/2.5.22 Version/10.50"` 82.146.59.209 - - [10/Jun/2010:01:54:10 +0000] "GET http://www.yandex.ru/ HTTP/1.0" 200 8859 "http://www.yandex.ru/" "Mozilla/5.0 (Windows; U; Windows NT 5.1; ru; rv:1.9.2.2) Gecko/20100316 Firefox/3.6.2"` 82.146.41.7 - - [10/Jun/2010:02:55:34 +0000] "GET http://www.yandex.ru/ HTTP/1.0" 200 8859 "http://www.yandex.ru/" "Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/532.5 (KHTML, like Gecko) Chrome/4.1.249.1045 Safari/532.5" 125.45.109.166 - - [09/Jun/2010:11:04:17 +0000] "GET http://proxyjudge1.proxyfire.net/fastenv HTTP/1.1" 404 1010 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)"

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• How do I install on an UEFI Asus 1215b netbook?

  - by Tarek

  I'm trying to install Ubuntu 11.10 on a UEFI netbook Asus 1215b using an USB stick. I created a fat32 efi partition of 100MB, 2GB swap, and 2 ext4 partitions (for root (/ ) and /home, respectively). While installing, Ubuntu switches to CLI and starts running efibootmgr. After a few commands (sadly I don't have a screen grab), it stops displaying text but it's still running judging by the HDD led. Then, there's a weird graphic glitch and the screen turns off (HDD led still indicating activity). Finally, it just stops, but doesn't turn off. Not even a hard reboot works (holding down the power button a few secs). I have to plug the netbook off and remove the battery. After that, it still doesn't boot Ubuntu... Anyway, what can I do? I'm considering following the footsteps here and here. Edit: here is the syslog $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] BUG: unable to handle kernel paging request at 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] IP: [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] PGD 14ecc067 PUD 0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Oops: 0000 [#1] SMP $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CPU 0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Modules linked in: cryptd aes_x86_64 ufs qnx4 hfsplus hfs minix ntfs msdos xfs reiserfs jfs bnep parport_pc rfcomm dm_crypt ppdev bluetooth lp parport joydev eeepc_wmi asus_wmi sparse_keymap uvcvideo videodev v4l2_compat_ioctl32 snd_hda_codec_realtek snd_seq_midi snd_hda_codec_hdmi snd_hda_intel snd_hda_codec arc4 snd_rawmidi snd_hwdep psmouse snd_pcm snd_seq_midi_event ath9k serio_raw sp5100_tco i2c_piix4 k10temp snd_seq mac80211 snd_timer ath9k_common ath9k_hw snd_seq_device ath snd cfg80211 soundcore snd_page_alloc binfmt_misc squashfs overlayfs nls_iso8859_1 nls_cp437 vfat fat dm_raid45 xor dm_mirror dm_region_hash dm_log btrfs zlib_deflate libcrc32c usb_storage uas radeon video ahci libahci ttm drm_kms_helper drm wmi i2c_algo_bit atl1c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Pid: 28432, comm: efibootmgr Not tainted 3.0.0-12-generic #20-Ubuntu ASUSTeK Computer INC. 1215B/1215B $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RIP: 0010:[<ffff880066d44c1f>] [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RSP: 0018:ffff88005e2cbab0 EFLAGS: 00010082 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RAX: 00000000ffe1867c RBX: 0000000000000009 RCX: 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RDX: 0000000000000000 RSI: ffff88005e2cbbea RDI: ffff88005e2cbb40 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RBP: 00000000ffe1867c R08: 0000000000000000 R09: 0000000000000084 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] R10: ffffc9001101ff83 R11: ffffc90011018685 R12: 0000000000000001 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] R13: 0000000000000000 R14: ffffc9001101867c R15: ffff88005e2cbbe1 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] FS: 00007f9cdde13720(0000) GS:ffff880066a00000(0000) knlGS:0000000000000000 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CR2: 00000000ffe1867c CR3: 000000002dace000 CR4: 00000000000006f0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Process efibootmgr (pid: 28432, threadinfo ffff88005e2ca000, task ffff880014f0dc80) $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Stack: $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ffffc90011010000 ffff88005e2cbac8 0000000000010000 ffff880066d4401d $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] 000000000000007c ffff880009e84400 0000000000000090 ffff880066d45738 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ffffc9001101867c ffff880066d4331c 0000000000000009 ffffc9001101867b $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Call Trace: $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815e9efe>] ? _raw_spin_lock+0xe/0x20 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9c2d>] ? open+0x10d/0x1b0 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff8116554b>] ? __dentry_open+0x2bb/0x320 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9b20>] ? bin_vma_open+0x70/0x70 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815e9efe>] ? _raw_spin_lock+0xe/0x20 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811849ee>] ? vfsmount_lock_local_unlock+0x1e/0x30 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff8104303b>] ? efi_call5+0x4b/0x80 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81042a7f>] ? virt_efi_set_variable+0x2f/0x40 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff814bb125>] ? efivar_create+0x1e5/0x280 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9d63>] ? write+0x93/0x190 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff811d9de4>] ? write+0x114/0x190 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81167813>] ? vfs_write+0xb3/0x180 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff81167b3a>] ? sys_write+0x4a/0x90 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] [<ffffffff815f22c2>] ? system_call_fastpath+0x16/0x1b $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] Code: ec 01 75 f0 41 bc 01 00 00 00 e8 e5 fb ff ff e8 e4 fc ff ff 33 c0 44 0f b7 c0 66 3b c3 73 20 41 0f b7 c0 41 0f b7 d0 03 c5 8b c8 <8a> 00 42 38 04 3a 75 0a 66 45 03 c4 66 44 3b c3 72 e2 33 c0 66 $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RIP [<ffff880066d44c1f>] 0xffff880066d44c1e $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] RSP <ffff88005e2cbab0> $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] CR2: 00000000ffe1867c $Oct 21 01:05:17 ubuntu kernel: [ 1220.544009] ---[ end trace 493844b002da4787 ]---

  Read the article

• CD/DVD drive not mounted when inserted with Disc of any kind

  - by Cisco Sán

  I just noticed that if a insert a CD or a DVD of any kind, the Drive will start spinning but it will not show the mounted disc. Before it used to ask me what to do with the media inserted. Now it doesn't even do that. I ran in the terminal this code: eject -n and it displays this: " eject: device is `/dev/sr0'" what can I do to get the functionality back on my drive. also ran this command: sudo mount -o ro,unhide,uid=1000 /dev/cdrom /mnt/cdrom but in return i get this: " mount: mount point /mnt/cdrom does not exist" Running Ubuntu 11.10 HERE IS THE HISTORY UNTIL NOW thanks Waltinator: I ran the 'dmesg' but don't know what I'm looking for. Im a newbie on this. The same thing with the 'ls -rlt /var/log' command. Should I create the directory for the mount? at this point really don't know what to do. – Cisco Sán 7 hours ago Here are 3 lines from my dmesg after I successfully inserted a CD: [ 4804.416018] wlan0: no IPv6 routers present [ 8214.125450] ISdit ISO 9660 Extensions: Microsoft Joliet Level 3 [ 8214.136556] ISO 9660 Extensions: RRIP_1991A The first line is a previous event, my wireless going online. The next 2 lines are a good result. The number in square brackets is "seconds since boot", the rest of the line is usually helpful. And no, you should NOT create the mount point. Let's try to get the automatic mounting to work. – waltinator 7 hours ago ok this are my last 3 lines on the 'dmesg' [ 18.130819] init: plymouth-stop pre-start process (1396) terminated with status 1 [ 28.780011] wlan0: no IPv6 routers present [ 505.632119] CE: hpet increased min_delta_ns to 20113 nsec – Cisco Sán 6 hours ago It looks like your CD/DVD drive is not connected to the data bus, and not causing an interrupt when you insert a platter. – waltinator 6 hours ago Try dmesg | grep -A8 CD-ROM which should show you what the system thought was available when it came up. – waltinator 6 hours ago here is my printout [0.774351] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-T40N A100 PQ: 0 ANSI: 5 [0.778117] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [0.778122] cdrom: Uniform CD-ROM driver Revision: 3.20 [0.778282] sr 0:0:0:0: Attached scsi CD-ROM sr0 [0.778340] sr 0:0:0:0: Attached scsi generic sg0 type 5 [0.780416] Freeing unused kernel memory: 984k freed [0.780732] Write protecting the kernel read-only data: 10240k [0.780986] Freeing unused kernel memory: 20k freed [0.786331] Freeing unused kernel memory: 1400k freed [0.804912] udevd[90]: starting version 173 [0.874178] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [0.874208] r8169 0000:02:00.0: PCI INT A - GSI 16 (level, low) - IRQ 16 OK, your system sees the drive. Can you open and close the tray with eject and eject -t? Run udevadm monitor while you insert a CD (type ^C when done) and see if you get "change" and "add" messages. – waltinator 6 hours ago ok, "eject" works perfectly "eject -t" does nothing. this is the message for "udevadm monitor": KERNEL[13771.009267] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sr0 (block) UDEV [13773.878887] change /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0 /block/sr0 (block) – Cisco Sán 6 hours ago sudo hwinfo --cdrom (the hwinfo package is installable through Software Center) describes my CD-ROM, try it. – waltinator 4 hours ago My read out from the "sudo hwinfo --cdrom" are the following: hal.1: read hal dataprocess 2753: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 280. This is normally a bug in some application using the D-Bus library. libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files 22: SCSI 00.0: 10602 CD-ROM (DVD) [Created at block.247] Unique ID: KD9E.JgkxTS4hgl2 Parent ID: 3p2J.gdUMCD83e+E SysFS ID: /class/block/sr0 SysFS BusID: 0:0:0:0 SysFS Device Link: /devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0 Hardware Class: cdrom Model: "HL-DT-ST DVD+-RW GSA-T40N" Vendor: "HL-DT-ST" Device: "DVD+-RW GSA-T40N" Revision: "A100" Driver: "ata_piix", "sr" Driver Modules: "ata_piix" Device File: /dev/sr0 (/dev/sg0) Device Files: /dev/sr0, /dev/scd0, /dev/disk/by-id/ata-HL-DT-ST_DVD+_-RW_GSA-T40N_K048BJ74257, /dev/disk/by-path/pci-0000:00:1f.1-scsi-0:0:0:0, /dev/cdrom, /dev/cdrw, /dev/dvd, /dev/dvdrw Device Number: block 11:0 (char 21:0) Features: DVD Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #17 (IDE interface) Drive Speed: 31 Volume ID: "Movie" Publisher: "INTERVIDEO" Creation date: "20050424162207000" Thanks for the help. To Castro, hope this is what you meant and sorry for the comments..

  Read the article

• Exim mail server slow on sending through SMTP

  - by catalint

  It takes about 30 seconds for the server to send me the banner, but initial connection is done instantly only happens when I am at the office, from home it works fine at the office I have a rRns set-up for my client ip that it's not working. Server: Exim, public fixed ip, rDNS, no ports blocked, in a datacenter Config: hostlist loopback = <; 127.0.0.0/8 ; 0.0.0.0 ; ::1 ; 0000:0000:0000:0000:0000:ffff:7f00:0000/8 hostlist senderverifybypass_hosts = net-iplsearch;/etc/senderverifybypasshosts hostlist skipsmtpcheck_hosts = net-iplsearch;/etc/skipsmtpcheckhosts hostlist spammeripblocks = net-iplsearch;/etc/spammeripblocks hostlist backupmx_hosts = lsearch;/etc/backupmxhosts hostlist trustedmailhosts = lsearch;/etc/trustedmailhosts domainlist user_domains = ${if exists{/etc/userdomains} {lsearch;/etc/userdomains} fail} This happens super fast on the server: 30132 ident connection to 89.238.207.49 failed: Connection refused 30132 sender_fullhost = [89.238.207.49] 30132 sender_rcvhost = [89.238.207.49] 30132 Process 30132 is handling incoming connection from [89.238.207.49] 30132 host in host_lookup? no (option unset) 30132 set_process_info: 30132 handling incoming connection from [89.238.207.49] 30132 host in host_reject_connection? no (option unset) 30132 host in sender_unqualified_hosts? no (option unset) 30132 host in recipient_unqualified_hosts? no (option unset) 30132 host in helo_verify_hosts? no (option unset) 30132 host in helo_try_verify_hosts? no (option unset) 30132 host in helo_accept_junk_hosts? yes (matched "*") 30132 using ACL "acl_connect" 30132 processing "accept" 30132 check hosts = +trustedmailhosts 30132 sender host name required, to match against lsearch;/etc/trustedmailhosts 30132 looking up host name for 89.238.207.49 30132 IP address lookup yielded relay.easycomm.ro Client side 2011.09.14 13:08:13 SMTP (mail.server.ro): Begin execution 2011.09.14 13:08:13 SMTP (mail.server.ro): Port: 465, Secure: SSL, SPA: no 2011.09.14 13:08:13 SMTP (mail.server.ro): Finding host 2011.09.14 13:08:13 SMTP (mail.server.ro): Connecting to host 2011.09.14 13:08:13 SMTP (mail.server.ro): Securing connection 2011.09.14 13:08:13 SMTP (mail.server.ro): Connected to host ---> This is a 1 minute 5 seconds gap 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-genius.filipnet.ro ESMTP Exim 4.69 #1 Wed, 14 Sep 2011 13:09:26 +0300 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220-We do not authorize the use of this system to transport unsolicited, 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 220 and/or bulk e-mail. 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] EHLO CatalinDell 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-genius.filipnet.ro Hello CatalinDell [89.238.207.49] 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-SIZE 52428800 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-PIPELINING 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250-AUTH PLAIN LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 HELP 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorizing to server 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] AUTH LOGIN 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 VXNlcm5hbWU6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] dGVzdEBzcG9ydGd1cnUucm8= 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 334 UGFzc3dvcmQ6 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] ***** 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 235 Authentication succeeded 2011.09.14 13:09:18 SMTP (mail.server.ro): Authorized to host 2011.09.14 13:09:18 SMTP (mail.server.ro): Connected to host 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] MAIL FROM: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 OK 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] RCPT TO: <*****> 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 250 Accepted 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] DATA 2011.09.14 13:09:18 SMTP (mail.server.ro): <rx> 354 Enter message, ending with "." on a line by itself 2011.09.14 13:09:18 SMTP (mail.server.ro): [tx] . ---> This is a 1 minute 10 seconds gap 2011.09.14 13:10:28 SMTP (mail.server.ro): <rx> 250 OK id=1R3mPG-0004T4-7Q 2011.09.14 13:10:28 SMTP (mail.server.ro): End execution --- Initial info I've setup an email account on "Windows Live Mail" that comes with Windows 7 Receiving is super fast, but for some reason sending is very slow, I had to increase the outgoing timeout to 3 minutes in order to make it work. Server software is Exim / Dovecot / cPanel. Do you have any ideeas why there is a slow sending process? Thank you!

  Read the article

• System randomly Crashing

  - by Hailwood

  Hi guys, Computer is running windows XP. seems to be crashing randomly, no pattern in its timing or activity to cause it. What could be causing this/how do I diagnose this? Event log shows Event Type: Error Event Source: System Error Event Category: (102) Event ID: 1003 Date: 22/02/2011 Time: 7:10:05 p.m. User: N/A Computer: YOUR-8ABC512DA0 Description: Error code 1000008e, parameter1 c0000005, parameter2 bf801b50, parameter3 ee118c44, parameter4 00000000. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 31 30 30 30 30 30 38 1000008 0020: 65 20 20 50 61 72 61 6d e Param 0028: 65 74 65 72 73 20 63 30 eters c0 0030: 30 30 30 30 30 35 2c 20 000005, 0038: 62 66 38 30 31 62 35 30 bf801b50 0040: 2c 20 65 65 31 31 38 63 , ee118c 0048: 34 34 2c 20 30 30 30 30 44, 0000 0050: 30 30 30 30 0000

  Read the article

• Why is this LTO4 Tape-drive not working

  - by Tim Haegele

  # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

  Read the article

• How can I add leading zeros between delimiters in Excel 2010

  - by Gregory Biernacki

  I am trying to convert a list of property id numbers that has a standard format of 0000-A-00000-00-00, where my worksheet has the various combinations of 1-A-123 10-B-1234 Ideally they would read as follows 0001-A-00123-0000-00 0010-B-01234-0000-00 I've tried using the custom number formatting but it doesn't like the letter in the middle of the number. I didn't know if my only option was to break them apart and then put them back together again. I would accept a solution that merely put the leading zeros at the front of the number, (max is 4 characters) so the result could look like 0001-A-123

  Read the article

• DIsable my nv video card driver in linux

  - by Dahaka Wang

  I'm trying to passthrough my nv video card to my domU, but I could not bind my video card to the pciback driver I only have one video card with the pci number 0000:03:00.0, so I used the following command echo -n "0000:03:00.0" > /sys/bus/pci/drivers/nouveau/bind to unbind the nouveau driver from my video card. The screen went black because I have forcefully removed the video driver, therefore I ssh'd into the computer to run further commands I ran: echo -n "0000:03:00.0" > /sys/bus/pci/drivers/pciback/bind to try to bind it to my pciback driver, but I got: bash: echo: write error: No such device I found out that this was the message shown when trying to bind a PCI device which is already bound. Therefore, I think that something was still using my video card Can anyone help me out? Thanks a lot!

  Read the article

• Cant remove/delete symlink

  - by user477519

  I have tried to create a symlink and it threw this error: ln: accessing `.test': Permission denied Now I can't unlink or delete the symlink file. Tried Googling for help but could not find a solution. Please find the results of following commands. stat .test : File: `.test'stat: cannot read symbolic link `.test': Permission denied Size: 26 Blocks: 0 IO Block: 16384 symbolic link Device: 1fh/31d Inode: 312075453 Links: 1 Access: (0777/lrwxrwxrwx) Uid: (11160/ chatt) Gid: (11307/ pgr) Access: 2012-11-12 11:36:51.167327500 +0000 Modify: 2012-11-12 11:36:51.163331700 +0000 Change: 2012-11-12 11:36:51.163331700 +0000 Birth: - chattr -i .test: chattr: Permission denied while trying to stat .test lsatter .test lsattr: Operation not supported While reading flags on .test Any help would be appreciated. Thanks

  Read the article

• Problem with NHibernate

  - by Bernard Larouche

  I am trying to get a list of Products that share the Category. NHibernate returns no product which is wrong. Here is my Criteria API method : public IList<Product> GetProductForCategory(string name) { return _session.CreateCriteria(typeof(Product)) .CreateCriteria("Categories") .Add(Restrictions.Eq("Name", name)) .List<Product>(); } Here is my HQL method : public IList<Product> GetProductForCategory(string name) { return _session.CreateQuery("select from Product p, p.Categories.elements c where c.Name = :name").SetString("name",name).List<Product>(); } Both methods return no product when they should return 2 products. Here is the Mapping for the Product class : <?xml version="1.0" encoding="utf-8" ?> <hibernate-mapping xmlns="urn:nhibernate-mapping-2.2" assembly="CBL.CoderForTraders.DomainModel" namespace="CBL.CoderForTraders.DomainModel"> <class name="Product" table="Products" > <id name="_persistenceId" column="ProductId" type="Guid" access="field" unsaved-value="00000000-0000-0000-0000-000000000000"> <generator class="assigned" /> </id> <version name="_persistenceVersion" column="RowVersion" access="field" type="int" unsaved-value="0" /> <property name="Name" column="ProductName" type="String" not-null="true"/> <property name="Price" column="BasePrice" type="Decimal" not-null="true" /> <property name="IsTaxable" column="IsTaxable" type="Boolean" not-null="true" /> <property name="DefaultImage" column="DefaultImageFile" type="String"/> <bag name="Descriptors" table="ProductDescriptors"> <key column="ProductId" foreign-key="FK_Product_Descriptors"/> <one-to-many class="Descriptor"/> </bag> <bag name="Categories" table="Categories_Products" > <key column="ProductId" foreign-key="FK_Products_Categories"/> <many-to-many class="Category" column="CategoryId"></many-to-many> </bag> <bag name="Orders" generic="true" table="OrderProduct" > <key column="ProductId" foreign-key="FK_Products_Orders"/> <many-to-many column="OrderId" class="Order" /> </bag> </class> </hibernate-mapping> And finally the mapping for the Category class : <?xml version="1.0" encoding="utf-8" ?> <hibernate-mapping xmlns="urn:nhibernate-mapping-2.2" assembly="CBL.CoderForTraders.DomainModel" namespace="CBL.CoderForTraders.DomainModel" default-access="field.camelcase-underscore" default-lazy="true"> <class name="Category" table="Categories" > <id name="_persistenceId" column="CategoryId" type="Guid" access="field" unsaved-value="00000000-0000-0000-0000-000000000000"> <generator class="assigned" /> </id> <version name="_persistenceVersion" column="RowVersion" access="field" type="int" unsaved-value="0" /> <property name="Name" column="Name" type="String" not-null="true"/> <property name="IsDefault" column="IsDefault" type="Boolean" not-null="true" /> <property name="Description" column="Description" type="String" not-null="true" /> <many-to-one name="Parent" column="ParentID"></many-to-one> <bag name="SubCategories" inverse="true"> <key column="ParentID" foreign-key="FK_Category_ParentCategory" /> <one-to-many class="Category"/> </bag> <bag name="Products" table="Categories_Products"> <key column="CategoryId" foreign-key="FK_Categories_Products" /> <many-to-many column="ProductId" class="Product"></many-to-many> </bag> </class> </hibernate-mapping> Can you see what could be the problem ?

  Read the article

• Mouse pointer strange problem...

  - by Paska

  Hi all, i have last ubuntu installed (10.10), but from an year and thousand updates, video drivers updates, an hundreds of tricks, the mouse pointer is showed like an UGLY square... These are the screenshots: First Second I have no idea what to do to solve this problem. Anyone of you have an idea to solve it? Edit: this problem was encountered from 8.10+! Edit 2, Video card specifications: paska@ubuntu:~$ hwinfo --gfxcard 35: PCI 100.0: 0300 VGA compatible controller (VGA) [Created at pci.318] UDI: /org/freedesktop/Hal/devices/pci_1106_3230 Unique ID: VCu0.QX54AGQKWeE Parent ID: vSkL.CP+qXDDqow8 SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.0 SysFS BusID: 0000:01:00.0 Hardware Class: graphics card Model: "VIA K8M890CE/K8N890CE [Chrome 9]" Vendor: pci 0x1106 "VIA Technologies, Inc." Device: pci 0x3230 "K8M890CE/K8N890CE [Chrome 9]" SubVendor: pci 0x1043 "ASUSTeK Computer Inc." SubDevice: pci 0x81b5 Revision: 0x11 Memory Range: 0xd0000000-0xdfffffff (rw,prefetchable) Memory Range: 0xfa000000-0xfaffffff (rw,non-prefetchable) Memory Range: 0xfbcf0000-0xfbcfffff (ro,prefetchable,disabled) IRQ: 16 (10026 events) I/O Ports: 0x3c0-0x3df (rw) Module Alias: "pci:v00001106d00003230sv00001043sd000081B5bc03sc00i00" Driver Info #0: Driver Status: viafb is not active Driver Activation Cmd: "modprobe viafb" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #17 (PCI bridge) Primary display adapter: #35 paska@ubuntu:~$ thanks, A

  Read the article

• Davicom Semiconductor, Inc. 21x4x DEC-Tulip not detected by Wireshark but IP operational

  - by deepsix86

  Recently flipped to Ubuntu 11.10 on a Dell 4300 (Intel). Getting IP address and no issues (ping/surf) but Wireshark unable to detect eth0 interface. I see references in forums to blacklist tulip but looks like I am running dmfe. Not sure if the blacklist is required and where to go from here. Maybe Driver update? Got a little lost looking in that area. Some h/w details below (IP/MAC/HOSTNAME removed) Linux xxxxxx 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 17:34:21 UTC 2012 i686 i686 i386 GNU/Linux network-admin (HOSTS TAB) does not list eth0, only loopback and bunch of IPv6 interfaces ifconfig eth0 Link encap:Ethernet HWaddr xxxxxxxx inet addr:192.168.x.xx Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxx 64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36662 errors:0 dropped:1 overruns:0 frame:0 TX packets:24975 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42115779 (42.1 MB) TX bytes:3056435 (3.0 MB) Interrupt:18 Base address:0xe800 lspci 02:09.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) Subsystem: Device 4554:434e Flags: bus master, medium devsel, latency 64, IRQ 18 I/O ports at e800 [size=256] Memory at fe1ffc00 (32-bit, non-prefetchable) [size=256] Expansion ROM at fe200000 [disabled] [size=256K] Capabilities: [50] Power Management version 2 Kernel driver in use: dmfe Kernel modules: dmfe hwinfo --netcard 20: PCI 209.0: 0200 Ethernet controller [Created at pci.318] Unique ID: rBUF.0NgK5ZS9c0D Parent ID: 6NW+.siohrLUzzI4 SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:02:09.0 SysFS BusID: 0000:02:09.0 Hardware Class: network Model: "Davicom 21x4x DEC-Tulip compatible 10/100 Ethernet" Vendor: pci 0x1282 "Davicom Semiconductor, Inc." Device: pci 0x9102 "21x4x DEC-Tulip compatible 10/100 Ethernet" SubVendor: pci 0x4554 SubDevice: pci 0x434e Revision: 0x31 Driver: "dmfe" Driver Modules: "dmfe" Device File: eth0 I/O Ports: 0xe800-0xe8ff (rw) Memory Range: 0xfe1ffc00-0xfe1ffcff (rw,non-prefetchable) Memory Range: 0xfe200000-0xfe23ffff (ro,non-prefetchable,disabled) IRQ: 18 (61379 events) HW Address: 00:08:a1:01:35:70 Link detected: yes Module Alias: "pci:v00001282d00009102sv00004554sd0000434Ebc02sc00i00" Driver Info #0: Driver Status: dmfe is active Driver Activation Cmd: "modprobe dmfe" Config Status: cfg=new, avail=yes, need=no, active=unknown Attached to: #11 (PCI bridge)

  Read the article

• Using a portable USB monitor in Ubuntu 13.04 (AOC e1649Fwu - DisplayLink)

  Having access to a little bit of IT hardware extravaganza isn't that easy here in Mauritius for exactly two reasons - either it is simply not available or it is expensive like nowhere. Well, by chance I came across an advert by a local hardware supplier and their offer of the week caught my attention - a portable USB monitor. Sounds cool, and the specs are okay as well. It's completely driven via USB 2.0, has a light weight, the dimensions would fit into my laptop bag and the resolution of 1366 x 768 pixels is okay for a second screen. Long story, short ending: I called them and only got to understand that they are out of stock - how convenient! Well, as usual I left some contact details and got the regular 'We call you back' answer. Surprisingly, I didn't receive a phone call as promised and after starting to complain via social media networks they finally came back to me with new units available - and *drum-roll* still the same price tag as promoted (and free delivery on top as one of their employees lives in Flic en Flac). Guess, it was a no-brainer to get at least one unit to fool around with. In worst case it might end up as image frame on the shelf or so... The usual suspects... Ubuntu first! Of course, the packing mentions only Windows or Mac OS as supported operating systems and without hesitation at all, I hooked up the device on my main machine running on Ubuntu 13.04. Result: Blackout... Hm, actually not the situation I was looking for but okay can't be too difficult to get this piece of hardware up and running. Following the output of syslogd (or dmesg if you prefer) the device has been recognised successfully but we got stuck in the initialisation phase. Oct 12 08:17:23 iospc2 kernel: [69818.689137] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 12 08:17:23 iospc2 kernel: [69818.800306] usb 2-4: device descriptor read/64, error -32Oct 12 08:17:24 iospc2 kernel: [69819.043620] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 08:17:24 iospc2 kernel: [69819.043630] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 08:17:24 iospc2 kernel: [69819.043636] usb 2-4: Product: e1649FwuOct 12 08:17:24 iospc2 kernel: [69819.043642] usb 2-4: Manufacturer: DisplayLinkOct 12 08:17:24 iospc2 kernel: [69819.043647] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 08:17:24 iospc2 kernel: [69819.046073] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 08:17:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 08:17:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 12 08:17:30 iospc2 kernel: [69825.411220] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 12 08:17:30 iospc2 kernel: [69825.498778] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 12 08:17:30 iospc2 kernel: [69825.498786] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 12 08:17:30 iospc2 kernel: [69825.498909] usbcore: registered new interface driver udl The device has been recognised as USB device without any question and it is listed properly: # lsusb...Bus 002 Device 005: ID 17e9:4107 DisplayLink ... A quick and dirty research on the net gave me some hints towards the udlfb framebuffer device for USB DisplayLink devices. By default this kernel module is blacklisted $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udl#blacklist udlblacklist udlfb and it is recommended to load it manually. So, unloading the whole udl stack and giving udlfb a shot: Oct 12 08:22:31 iospc2 kernel: [70126.642809] usbcore: registered new interface driver udlfb But still no reaction on the external display which supposedly should have been on and green. Display okay? Test run on Windows Just to be on the safe side and to exclude any hardware related defects or whatsoever - you never know what happened during delivery. I moved the display to a new position on the opposite side of my laptop, installed the display drivers first in Windows Vista (I know, I know...) as recommended in the manual, and then finally hooked it up on that machine. Tada! Display has been recognised correctly and I have a proper choice between cloning and extending my desktop. Testing whether the display is working properly - using Windows Vista Okay, good to know that there is nothing wrong on the hardware side just software... Back to Ubuntu - Kernel too old Some more research on Google and various hits recommend that the original displaylink driver has been merged into the recent kernel development and one should manually upgrade the kernel image (and both header) packages for Ubuntu. At least kernel 3.9 or higher would be necessary, and so I went out to this URL: http://kernel.ubuntu.com/~kernel-ppa/mainline/ and I downloaded all the good stuff from the v3.9-raring directory. The installation itself is easy going via dpkg: $ sudo dpkg -i linux-image-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb$ sudo dpkg -i linux-headers-3.9.0-030900_3.9.0-030900.201304291257_all.deb$ sudo dpkg -i linux-headers-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb As with any kernel upgrades it is necessary to restart the system in order to use the new one. Said and done: $ uname -r3.9.0-030900-generic And now connecting the external display gives me the following output in /var/log/syslog: Oct 12 17:51:36 iospc2 kernel: [ 2314.984293] usb 2-4: new high-speed USB device number 6 using ehci-pciOct 12 17:51:36 iospc2 kernel: [ 2315.096257] usb 2-4: device descriptor read/64, error -32Oct 12 17:51:36 iospc2 kernel: [ 2315.337105] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 17:51:36 iospc2 kernel: [ 2315.337115] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 17:51:36 iospc2 kernel: [ 2315.337122] usb 2-4: Product: e1649FwuOct 12 17:51:36 iospc2 kernel: [ 2315.337127] usb 2-4: Manufacturer: DisplayLinkOct 12 17:51:36 iospc2 kernel: [ 2315.337132] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338292] udlfb: DisplayLink e1649Fwu - serial #FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338299] udlfb: vid_17e9&pid_4107&rev_0129 driver's dlfb_data struct at ffff880117e59000Oct 12 17:51:36 iospc2 kernel: [ 2315.338303] udlfb: console enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338306] udlfb: fb_defio enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338309] udlfb: shadow enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338468] udlfb: vendor descriptor length:17 data:17 5f 01 0015 05 00 01 03 00 04Oct 12 17:51:36 iospc2 kernel: [ 2315.338473] udlfb: DL chip limited to 1500000 pixel modesOct 12 17:51:36 iospc2 kernel: [ 2315.338565] udlfb: allocated 4 65024 byte urbsOct 12 17:51:36 iospc2 kernel: [ 2315.343592] hid-generic 0003:17E9:4107.0009: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 17:51:36 iospc2 mtp-probe: checking bus 2, device 6: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 17:51:36 iospc2 mtp-probe: bus: 2, device: 6 was not an MTP deviceOct 12 17:51:36 iospc2 kernel: [ 2315.426583] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.426589] udlfb: Reallocating framebuffer. Addresses will change!Oct 12 17:51:36 iospc2 kernel: [ 2315.428338] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.428343] udlfb: set_par mode 1366x768Oct 12 17:51:36 iospc2 kernel: [ 2315.430620] udlfb: DisplayLink USB device /dev/fb1 attached. 1366x768 resolution. Using 4104K framebuffer memory Okay, that's looks more promising but still only blackout on the external screen... And yes, due to my previous modifications I swapped the blacklisted kernel modules: $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udlblacklist udl#blacklist udlfb Silly me! Okay, back to the original situation in which udl is allowed and udlfb blacklisted. Now, the logging looks similar to this and the screen shows those maroon-brown and azure-blue horizontal bars as described on other online resources. Oct 15 21:27:23 iospc2 kernel: [80934.308238] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 15 21:27:23 iospc2 kernel: [80934.420244] usb 2-4: device descriptor read/64, error -32Oct 15 21:27:24 iospc2 kernel: [80934.660822] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 15 21:27:24 iospc2 kernel: [80934.660832] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 15 21:27:24 iospc2 kernel: [80934.660838] usb 2-4: Product: e1649FwuOct 15 21:27:24 iospc2 kernel: [80934.660844] usb 2-4: Manufacturer: DisplayLinkOct 15 21:27:24 iospc2 kernel: [80934.660850] usb 2-4: SerialNumber: FJBD7HA000778Oct 15 21:27:24 iospc2 kernel: [80934.663391] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 15 21:27:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 15 21:27:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 15 21:27:25 iospc2 kernel: [80935.742407] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 15 21:27:25 iospc2 kernel: [80935.834403] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 15 21:27:25 iospc2 kernel: [80935.834416] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 15 21:27:25 iospc2 kernel: [80935.836389] usbcore: registered new interface driver udlOct 15 21:27:25 iospc2 kernel: [80936.021458] [drm] write mode info 153 Next, it's time to enable the display for our needs... This can be done either via UI or console, just as you'd prefer it. Adding the external USB display under Linux isn't an issue after all... Settings Manager => Display Personally, I like the console. With the help of xrandr we get the screen identifier first $ xrandrScreen 0: minimum 320 x 200, current 3200 x 1080, maximum 32767 x 32767LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm...DVI-0 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm   1366x768       60.0*+ and then give it the usual shot with auto-configuration. Let the system decide what's best for your hardware... $ xrandr --output DVI-0 --off$ xrandr --output DVI-0 --auto And there we go... Cloned output of main display: New kernel, new display... The external USB display works out-of-the-box with a Linux kernel > 3.9.0. Despite of a good number of resources it is absolutely not necessary to create a Device or Screen section in one of Xorg.conf files. This information belongs to the past and is not valid on kernel 3.9 or higher. Same hardware but Windows 8 Of course, I wanted to know how the latest incarnation from Redmond would handle the new hardware... Flawless! Most interesting aspect here: I did not use the driver installation medium on purpose. And I was right... not too long afterwards a dialog with the EULA of DisplayLink appeared on the main screen. And after confirmation of same it took some more seconds and the external USB monitor was ready to rumble. Well, and not only that one... but see for yourself. This time Windows 8 was the easiest solution after all. Resume I can highly recommend this type of hardware to anyone asking me. Although, it's dimensions are 15.6" it is actually lighter than my Samsung Galaxy Tab 10.1 and it still fits into my laptop bag without any issues. From now on... no more single screen while developing software on the road!

  Read the article

• Updated Intel display driver causing errors when booting

  - by cdysthe

  I upgraded to to Graphics Installer 1.0.6 on my Ubuntu 14.04 and installed the drivers using the Intel Graphics Installer. The laptop is Intel Ivybridge powered with Intel HD graphics. It Optimus but I have disabled the Nvidia card in bios. The Intel Graphics Installer installs the package i915-3.15-3.13-dkms.deb which I assume is the updated driver. It causes a bunch of error messages when I boot. Here are the relevant errors from dmesg when I boot: [ 7.206151] drm: module verification failed: signature and/or required key missing - tainting kernel [ 7.208045] drm: module has bad taint, not creating trace events [ 7.336470] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver [ 7.393854] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013) [ 7.393855] [drm] Driver supports precise vblank timestamp query. [ 7.393921] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 7.505798] [drm] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 [ 7.507233] init: Failed to obtain startpar-bridge instance: Unknown parameter: INSTANCE [ 7.944183] [drm:cpt_serr_int_handler] ERROR PCH transcoder A FIFO underrun [ 8.368479] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device [ 8.368480] i915 0000:00:02.0: registered panic notifier [ 8.818416] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off What could the problem be and will it affect performance? I tried to remove the package and the errors went away but I'm then running and older driver I assume?

  Read the article

• Ubuntu 12.04 taking too much time to boot

  - by adarshdinesh

  Ubuntu 12.04 is taking much time for booting, Here is the system kernel message while booting .It is showing that some anacron was killed ,why ? and how to fix the problem ? [ 2.241047] scsi6 : usb-storage 2-1.6:1.0 [ 2.241501] usbcore: registered new interface driver usb-storage [ 2.241895] USB Mass Storage support registered. [ 3.240670] scsi 6:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 3.241791] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.243083] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 12.568641] Adding 4037904k swap on /dev/sda3. Priority:-1 extents:1 across:4037904k [ 12.615014] udevd[462]: starting version 175 [ 12.651334] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 12.655283] [drm] Initialized drm 1.1.0 20060810 ................... [ 14.118369] init: alsa-restore main process (982) terminated with status 19 [ 14.252595] init: anacron main process (1033) killed by TERM signal [ 14.285763] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0 [ 14.285841] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 14.285925] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 14.285991] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 14.615073] init: plymouth-stop pre-start process (1222) terminated with status 1 [ 16.447287] wlan0: authenticate with c0:8a:de:7c:60:e8 (try 1) [ 16.448858] wlan0: authenticated [ 16.453405] wlan0: associate with c0:8a:de:7c:60:e8 (try 1) [ 16.456392] wlan0: RX AssocResp from c0:8a:de:7c:60:e8 (capab=0x431 status=0 aid=2) [ 16.456398] wlan0: associated [ 16.457014] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 16.457017] ieee80211 phy0: brcmsmac: brcms_ops_bss_info_changed: associated [ 16.457019] ieee80211 phy0: changing basic rates failed: -22 [ 16.457021] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 16.457226] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 16.654196] ieee80211 phy0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 17.823565] ieee80211 phy0: wl0: brcms_c_d11hdrs_mac80211: txop exceeded phylen 180/256 dur 1946/1504 [ 18.220865] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 26.881422] wlan0: no IPv6 routers present [ 68.228293] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 73.240133] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 76.574490] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 102.180006] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 103.100984] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 124.171624] ieee80211 phy0: brcms_ops_bss_info_changed: qos enabled: true (implement)

  Read the article

• Firefox on wine crashes on startup on Ubuntu

  - by Iam Zesh

  First, let's explain why I want Firefox under wine, and not the Firefox that is shipped out of the box with Ubuntu. I want to use Firefox under wine because I want to use the Widevine addon, which is "at this time not available for linux". Here is what I did so far to install and use Firefox on wine. On Ubuntu 12.04 LTS, I just installed wine like that: sudo apt-get update; sudo apt-get install wine Then I downloaded the windows installer for Firefox from the mozilla website. I ran the Firefox Setup 25.0.exe file with wine but at the end of the install process when launching Firefox, I got a window notifying me that the program at crashed. I ran Firefox from the command line with wine, to get an idea of what could have went wrong: wine /home/myUser/.wine/drive_c/Program\ Files/Mozilla\ Firefox/firefox.exe fixme:heap:HeapSetInformation (nil) 1 (nil) 0 fixme:process:SetProcessDEPPolicy (1): stub fixme:iphlpapi:NotifyAddrChange (Handle 0x368e8fc, overlapped 0x368e8e0): stub fixme:winsock:WSCGetProviderPath ({e70f1aa0-ab8b-11cf-8ca3-00805f48a192} 0x44fe6f8 0x44fe6b8 0x44fe6e4) Stub! fixme:advapi:RegisterTraceGuidsW (0x1b0e290, 0x39ead80, {509962e0-406b-46f4-99ba-5a009f8d2225}, 3, 0x3974d00, (null), (null), 0x39eadb0,): stub fixme:winsock:WSCGetProviderPath ({e70f1aa0-ab8b-11cf-8ca3-00805f48a192} 0x44fe6f8 0x44fe6b8 0x44fe6e4) Stub! fixme:winsock:WSCGetProviderPath ({11058240-be47-11cf-95c8-00805f48a192} 0x44fe6f8 0x44fe6b8 0x44fe6e4) Stub! fixme:winsock:WSCGetProviderPath ({11058241-be47-11cf-95c8-00805f48a192} 0x44fe6f8 0x44fe6b8 0x44fe6e4) Stub! fixme:winsock:WSCGetProviderPath ({11058241-be47-11cf-95c8-00805f48a192} 0x44fe6f8 0x44fe6b8 0x44fe6e4) Stub! fixme:ntdll:NtLockFile I/O completion on lock not implemented yet fixme:advapi:SetNamedSecurityInfoW L"C:\\users\\myUser\\Application Data\\Mozilla\\Firefox\\Profiles\\cn4oy6kh.default\\extensions.ini" 1 536870916 (nil) (nil) 0x13d40c (nil) fixme:imm:ImmReleaseContext (0x20022, 0x13e850): stub fixme:win:EnumDisplayDevicesW ((null),0,0x32ee18,0x00000000), stub! fixme:shell:ApplicationAssociationRegistration_QueryCurrentDefault (0x143b50)->(L"webcal", 1, 1, 0x32c7a0) fixme:shell:ApplicationAssociationRegistration_QueryCurrentDefault (0x143b50)->(L"ircs", 1, 1, 0x32c7a0) fixme:shell:ApplicationAssociationRegistration_QueryCurrentDefault (0x143b50)->(L"mailto", 1, 1, 0x32c7a0) fixme:shell:ApplicationAssociationRegistration_QueryCurrentDefault (0x143b50)->(L"irc", 1, 1, 0x32c7a0) fixme:alsa:AudioSessionControl_SetGroupingParam (0x153050)->({7b0a93ee-05e7-4576-9cc5-64fdf201f303}, (null)) - stub fixme:alsa:AudioSessionControl_SetGroupingParam (0x153050)->({00000000-0000-0000-0000-000000000000}, (null)) - stub fixme:alsa:AudioSessionControl_UnregisterAudioSessionNotification (0x153050)->(0x6311880) - stub wine: Call from 0x7b839cf2 to unimplemented function dwmapi.dll.DwmGetCompositionTimingInfo, aborting fixme:dbghelp:elf_search_auxv can't find symbol in module Unfortunately I don't know what to do from there on...

  Read the article

• Microsoft IntelliMouse episodic pauses

  - by Rob Hills

  I have a Microsoft IntelliMouse connected via USB to a computer (directly, NOT via hub) currently running Ubuntu 11.10, but this problem also existed before we upgraded from 10.10. Every now and then (apparently randomly) the computer "pauses" for anything up to a few seconds. This usually occurs after a mouse movement and during the pause, the computer is completely unresponsive to mouse or keyboard. lsusb shows: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0409:0058 NEC Corp. HighSpeed Hub Bus 001 Device 004: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 013: ID 045e:001e Microsoft Corp. IntelliMouse Explorer Bus 001 Device 005: ID 04a9:1097 Canon, Inc. PIXMA iP5000 Bus 001 Device 006: ID 0a5c:200a Broadcom Corp. Bluetooth dongle Bus 001 Device 007: ID 0911:1c57 Philips Speech Processing Bus 001 Device 008: ID 04a9:2219 Canon, Inc. CanoScan 9950F so the mouse appears to be correctly identified. Syslog episodically shows the following sequence: Jan 15 11:48:32 kayes-computer kernel: [10588.512036] usb 3-1: USB disconnect, device number 10 Jan 15 11:48:33 kayes-computer kernel: [10589.248026] usb 3-1: new low speed USB device number 11 using uhci_hcd Jan 15 11:48:33 kayes-computer mtp-probe: checking bus 3, device 11: "/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-1" Jan 15 11:48:33 kayes-computer kernel: [10589.448596] input: Microsoft Microsoft IntelliMouse® Explorer as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input11 Jan 15 11:48:33 kayes-computer kernel: [10589.448706] generic-usb 0003:045E:001E.000B: input,hidraw0: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.1-1/input0 Jan 15 11:48:33 kayes-computer mtp-probe: bus: 3, device: 11 was not an MTP device though I can't confirm if these are directly associated with the "pauses". Any thoughts on what might be causing this or what else I can do to diagnose the problem?

  Read the article

• Why are my videos playing speeded up with no audio, but work fine if I log in as a guest?

  - by Martins Kruze

  Since the start of this week I have been experiencing a glitch in the multimedia on my Samsung R518 laptop. I have 2 problems: Videos in every player are speeded up around 2 or 4 times (including youtube.com (both HTML5 and flash variants), any other video on the web and videos on my laptop played by Totem Media Player), exception is VLC player, but 2nd problem does concern even that. There is no sound - simple as that (with or without headphones plugged in). These all problems are now, and has not seen before, I upgraded to Ubuntu 10.10 after it was possible, and from start I didn't have anything from this - it just started in this week. I haven't even putted new software in. I have more or less solved the question (kind of) - I just logged in as a guest - and it all works, but when I make a new user - it does not. Please help me. Some stats below: sudo lshw -c sound *-multimedia description: Audio device product: RV710/730 vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:48 memory:cfeec000-cfeeffff *-multimedia description: Audio device product: 82801I (ICH9 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:47 memory:fc200000-fc203fff sudo lshw -c video *-display description: VGA compatible controller product: M92 LP [Mobility Radeon HD 4300 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:46 memory:d0000000-dfffffff ioport:2000(size=256) memory:cfef0000-cfefffff memory:cfe00000-cfe1ffff

  Read the article

• Unable to make sound play in headset

  - by user50849

  Top right, I click the sound icon, select sound settings, and connect my USB-headset. I can them see the headset being detected as it pops up in the menu. I click it, and expect the currently played audio to get sent to the headset instead. My problem is that it does not. The audio keeps playing through the built-in speakers. More info: The icon for my built-in card in the sound settings is a circuit with a note symbol on top. The symbol for the headset is just black background with a "No" symbol on it. Might mean it doesn't work somehow. I installed pavucontrol, and notice that no second sound card shows up in there. When connecting, the syslog says Jun 20 09:38:46 yuna kernel: [40144.553431] usb 2-1.2: new full-speed USB device number 11 using ehci_hcd Jun 20 09:38:46 yuna kernel: [40144.650609] input: C-Media USB Headphone Set as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input20 Jun 20 09:38:46 yuna kernel: [40144.650895] generic-usb 0003:0D8C:000C.000B: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-0000:00:1d.0-1.2/input3 Jun 20 09:38:46 yuna mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2" Jun 20 09:38:46 yuna mtp-probe: bus: 2, device: 11 was not an MTP device

  Read the article

• About output of vga_switcher

  - by zhangjie

  When IGD and DIS both exist in my pc,and I want to disable DIS,so I create a service to switch on and off the DIS.It works.Finally,I decide to add the service command into /etc/rc.local so that DIS will be powered off automatically.Unfortunately,it fails.There's only one command added by myself in the file /etc/rc.local,so I can affirm failure is caused by that added command. Before,I directly added the command "echo OFF /sys/kernel/debug..." into /etc/rc.local,and when I restarted,the system startup fails.So I thought maybe when the command is executed,the DIS hasn't been powered on or ready for work.So conflict occurs!It's just my prediction.Then I added one line command "sleep 1s" before the "echo OFF ...",it works nearly everytime when I start or restart pc,while fails sometimes. The output result of "cat /sys/kernel/debug..." is as following: 0:IGD:+:Pwr:0000:00:02.0 1:DIS: :Pwr:0000:01:00.0 I want know 0000:00:02.0 means what?Time of first power on? If it was really time,I can set the command "sleep 2s" to wait for DIS powered on then "echo OFF ..." Thanks for your advice!

  Read the article

• Why does Cacti keep waiting for dead poller processes?

  - by Oliver Salzburg

  sorry for the length I am currently setting up a new Debian (6.0.5) server. I put Cacti (0.8.7g) on it yesterday and have been battling with it ever since. Initial issue The initial issue I was observing, was that my graphs weren't updating. So I checked my cacti.log and found this concerning message: POLLER: Poller[0] Maximum runtime of 298 seconds exceeded. Exiting. That can't be good, right? So I went checking and started poller.php myself (via sudo -u www-data php poller.php --force). It will pump out a lot of message (which all look like what I would expect) and then hang for a minute. After that 1 minute, it will loop the following message: Waiting on 1 of 1 pollers. This goes on for 4 more minutes until the process is forcefully ended for running longer than 300s. So far so good I went on for a good hour trying to determine what poller might still be running, until I got to the conclusion that there simply is no running poller. Debugging I checked poller.php to see how that warning is issued and why. On line 368, Cacti will retrieve the number of finished processes from the database and use that value to calculate how many processes are still running. So, let's see that value! I added the following debug code into poller.php: print "Finished: " . $finished_processes . " - Started: " . $started_processes . "\n"; Result This will print the following within seconds of starting poller.php: Finished: 0 - Started: 1 Waiting on 1 of 1 pollers. Finished: 1 - Started: 1 So the values are being read and are valid. Until we get to the part where it keeps looping: Finished: - Started: 1 Waiting on 1 of 1 pollers. Suddenly, the value is gone. Why? Putting var_dump() in there confirms the issue: NULL Finished: - Started: 1 Waiting on 1 of 1 pollers. The return value is NULL. How can that be when querying SELECT COUNT()...? (SELECT COUNT() should always return one result row, shouldn't it?) More debugging So I went into lib\database.php and had a look at that db_fetch_cell(). A bit of testing confirmed, that the result set is actually empty. So I added my own database query code in there to see what that would do: $finished_processes = db_fetch_cell("SELECT count(*) FROM poller_time WHERE poller_id=0 AND end_time>'0000-00-00 00:00:00'"); print "Finished: " . $finished_processes . " - Started: " . $started_processes . "\n"; $mysqli = new mysqli("localhost","cacti","cacti","cacti"); $result = $mysqli->query("SELECT COUNT(*) FROM poller_time WHERE poller_id=0 AND end_time>'0000-00-00 00:00:00';"); $row = $result->fetch_assoc(); var_dump( $row ); This will output Finished: - Started: 1 array(1) { ["COUNT(*)"]=> string(1) "2" } Waiting on 1 of 1 pollers. So, the data is there and can be accessed without any problems, just not with the method Cacti is using? Double-check that! I enabled MySQL logging to make sure I'm not imagining things. Sure enough, when the error message is looped, the cacti.log reads as if it was querying like mad: 06/29/2012 08:44:00 PM - CMDPHP: Poller[0] DEVEL: SQL Cell: "SELECT count(*) FROM cacti.poller_time WHERE poller_id=0 AND end_time>'0000-00-00 00:00:00'" 06/29/2012 08:44:01 PM - CMDPHP: Poller[0] DEVEL: SQL Cell: "SELECT count(*) FROM cacti.poller_time WHERE poller_id=0 AND end_time>'0000-00-00 00:00:00'" 06/29/2012 08:44:02 PM - CMDPHP: Poller[0] DEVEL: SQL Cell: "SELECT count(*) FROM cacti.poller_time WHERE poller_id=0 AND end_time>'0000-00-00 00:00:00'" But none of these queries are logged my MySQL. Yet, when I add my own database query code, it shows up just fine. What the heck is going on here?

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >