Search Results

Search found 224 results on 9 pages for '2am'.

Page 9/9 | < Previous Page | 5 6 7 8 9 

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

    - by kce
    I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

    Read the article

  • CPU Utilization LAMP stack

    - by Max
    We've got an ec2 m2.4xlarge running Magento (centos 5.6, httpd 2.2, php 5.2.17 with eaccelerator 0.9.5.3, mysql 5.1.52). Right now we're getting a large traffic spike, and our top looks like this: top - 09:41:29 up 31 days, 1:12, 1 user, load average: 120.01, 129.03, 113.23 Tasks: 1190 total, 18 running, 1172 sleeping, 0 stopped, 0 zombie Cpu(s): 97.3%us, 1.8%sy, 0.0%ni, 0.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.4%st Mem: 71687720k total, 36898928k used, 34788792k free, 49692k buffers Swap: 880737784k total, 0k used, 880737784k free, 1586524k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2433 mysql 15 0 23.6g 4.5g 7112 S 564.7 6.6 33607:34 mysqld 24046 apache 16 0 411m 65m 28m S 26.4 0.1 0:09.05 httpd 24360 apache 15 0 410m 60m 25m S 26.4 0.1 0:03.65 httpd 24993 apache 16 0 410m 57m 21m S 26.1 0.1 0:01.41 httpd 24838 apache 16 0 428m 74m 20m S 24.8 0.1 0:02.37 httpd 24359 apache 16 0 411m 62m 26m R 22.3 0.1 0:08.12 httpd 23850 apache 15 0 411m 64m 27m S 16.8 0.1 0:14.54 httpd 25229 apache 16 0 404m 46m 17m R 10.2 0.1 0:00.71 httpd 14594 apache 15 0 404m 63m 34m S 8.4 0.1 1:10.26 httpd 24955 apache 16 0 404m 50m 21m R 8.4 0.1 0:01.66 httpd 24313 apache 16 0 399m 46m 22m R 8.1 0.1 0:02.30 httpd 25119 apache 16 0 411m 59m 23m S 6.8 0.1 0:01.45 httpd Questions: Would giving msyqld more memory help it cache queries and react faster? If so, how? Other than splitting mysql and php to separate servers (which we're about to do) is there anything else we could/should be doing? Thanks! UPDATE: Here's our my.cnf along with the output of mysqltuner. It looks like a cache problem. Thanks again! # cat /etc/my.cnf [client] port = **** socket = /var/lib/mysql/mysql.sock [mysqld] datadir=/mnt/persistent/mysql port=**** socket=/var/lib/mysql/mysql.sock key_buffer = 512M max_allowed_packet = 64M table_cache = 1024 sort_buffer_size = 8M read_buffer_size = 4M read_rnd_buffer_size = 2M myisam_sort_buffer_size = 64M thread_cache_size = 128M tmp_table_size = 128M join_buffer_size = 1M query_cache_limit = 2M query_cache_size= 64M query_cache_type = 1 max_connections = 1000 thread_stack = 128K thread_concurrency = 48 log-bin=mysql-bin server-id = 1 wait_timeout = 300 innodb_data_home_dir = /mnt/persistent/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size = 20G innodb_additional_mem_pool_size = 20M innodb_log_file_size = 64M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 innodb_thread_concurrency = 48 ft_min_word_len=3 [myisamchk] ft_min_word_len=3 key_buffer = 128M sort_buffer_size = 128M read_buffer = 2M write_buffer = 2M # ./mysqltuner.pl >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.52-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB +Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 2G (Tables: 26) [--] Data in InnoDB tables: 749M (Tables: 250) [!!] Total fragmented tables: 262 -------- Security Recommendations ------------------------------------------- -------- Performance Metrics ------------------------------------------------- [--] Up for: 31d 2h 30m 38s (680M q [253.371 qps], 2M conn, TX: 4825B, RX: 236B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 20.6G global + 15.1M per thread (1000 max threads) [OK] Maximum possible memory usage: 35.4G (51% of installed RAM) [OK] Slow queries: 0% (35K/680M) [OK] Highest usage of available connections: 53% (537/1000) [OK] Key buffer size / total MyISAM indexes: 512.0M/457.2M [OK] Key buffer hit rate: 100.0% (9B cached / 264K reads) [OK] Query cache efficiency: 42.3% (260M cached / 615M selects) [!!] Query cache prunes per day: 4384652 [OK] Sorts requiring temporary tables: 0% (1K temp sorts / 38M sorts) [!!] Joins performed without indexes: 100404 [OK] Temporary tables created on disk: 17% (7M on disk / 45M total) [OK] Thread cache hit rate: 99% (537 created / 2M connections) [!!] Table cache hit rate: 0% (1K open / 946K opened) [OK] Open file limit used: 9% (453/5K) [OK] Table locks acquired immediately: 99% (758M immediate / 758M locks) [OK] InnoDB data size / buffer pool: 749.3M/20.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 64M) join_buffer_size (> 1.0M, or always use indexes with joins) table_cache (> 1024)

    Read the article

  • Creating a podcast feed for iTunes & BlackBerry users using WCF Syndication

    - by brian_ritchie
     In my previous post, I showed how to create a RSS feed using WCF Syndication.  Next, I'll show how to add the additional tags needed to turn a RSS feed into an iTunes podcast.   A podcast is merely a RSS feed with some special characteristics: iTunes RSS tags.  These are additional tags beyond the standard RSS spec.  Apple has a good page on the requirements. Audio file enclosure.  This is a link to the audio file (such as mp3) hosted by your site.  Apple doesn't host the audio, they just read the meta-data from the RSS feed into their system. The SyndicationFeed class supports both AttributeExtensions & ElementExtensions to add custom tags to the RSS feeds. A couple of points of interest in the code below: The imageUrl below provides the album cover for iTunes (170px × 170px) Each SyndicationItem corresponds to an audio episode in your podcast So, here's the code: .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: Consolas, "Courier New", Courier, Monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } 1: XNamespace itunesNS = "http://www.itunes.com/dtds/podcast-1.0.dtd"; 2: string prefix = "itunes"; 3:   4: var feed = new SyndicationFeed(title, description, new Uri(link)); 5: feed.Categories.Add(new SyndicationCategory(category)); 6: feed.AttributeExtensions.Add(new XmlQualifiedName(prefix, 7: "http://www.w3.org/2000/xmlns/"), itunesNS.NamespaceName); 8: feed.Copyright = new TextSyndicationContent(copyright); 9: feed.Language = "en-us"; 10: feed.Copyright = new TextSyndicationContent(DateTime.Now.Year + " " + ownerName); 11: feed.ImageUrl = new Uri(imageUrl); 12: feed.LastUpdatedTime = DateTime.Now; 13: feed.Authors.Add(new SyndicationPerson() {Name=ownerName, Email=ownerEmail }); 14: var extensions = feed.ElementExtensions; 15: extensions.Add(new XElement(itunesNS + "subtitle", subTitle).CreateReader()); 16: extensions.Add(new XElement(itunesNS + "image", 17: new XAttribute("href", imageUrl)).CreateReader()); 18: extensions.Add(new XElement(itunesNS + "author", ownerName).CreateReader()); 19: extensions.Add(new XElement(itunesNS + "summary", description).CreateReader()); 20: extensions.Add(new XElement(itunesNS + "category", 21: new XAttribute("text", category), 22: new XElement(itunesNS + "category", 23: new XAttribute("text", subCategory))).CreateReader()); 24: extensions.Add(new XElement(itunesNS + "explicit", "no").CreateReader()); 25: extensions.Add(new XDocument( 26: new XElement(itunesNS + "owner", 27: new XElement(itunesNS + "name", ownerName), 28: new XElement(itunesNS + "email", ownerEmail))).CreateReader()); 29:   30: var feedItems = new List<SyndicationItem>(); 31: foreach (var i in Items) 32: { 33: var item = new SyndicationItem(i.title, null, new Uri(link)); 34: item.Summary = new TextSyndicationContent(i.summary); 35: item.Id = i.id; 36: if (i.publishedDate != null) 37: item.PublishDate = (DateTimeOffset)i.publishedDate; 38: item.Links.Add(new SyndicationLink() { 39: Title = i.title, Uri = new Uri(link), 40: Length = i.size, MediaType = i.mediaType }); 41: var itemExt = item.ElementExtensions; 42: itemExt.Add(new XElement(itunesNS + "subtitle", i.subTitle).CreateReader()); 43: itemExt.Add(new XElement(itunesNS + "summary", i.summary).CreateReader()); 44: itemExt.Add(new XElement(itunesNS + "duration", 45: string.Format("{0}:{1:00}:{2:00}", 46: i.duration.Hours, i.duration.Minutes, i.duration.Seconds) 47: ).CreateReader()); 48: itemExt.Add(new XElement(itunesNS + "keywords", i.keywords).CreateReader()); 49: itemExt.Add(new XElement(itunesNS + "explicit", "no").CreateReader()); 50: itemExt.Add(new XElement("enclosure", new XAttribute("url", i.url), 51: new XAttribute("length", i.size), new XAttribute("type", i.mediaType))); 52: feedItems.Add(item); 53: } 54:   55: feed.Items = feedItems; If you're hosting your podcast feed within a MVC project, you can use the code from my previous post to stream it. Once you have created your feed, you can use the Feed Validator tool to make sure it is up to spec.  Or you can use iTunes: Launch iTunes. In the Advanced menu, select Subscribe to Podcast. Enter your feed URL in the text box and click OK. After you've verified your feed is solid & good to go, you can submit it to iTunes.  Launch iTunes. In the left navigation column, click on iTunes Store to open the store. Once the store loads, click on Podcasts along the top navigation bar to go to the Podcasts page. In the right column of the Podcasts page, click on the Submit a Podcast link. Follow the instructions on the Submit a Podcast page. Here are the full instructions.  Once they have approved your podcast, it will be available within iTunes. RIM has also gotten into the podcasting business...which is great for BlackBerry users.  They accept the same enhanced-RSS feed that iTunes uses, so just create an account with them & submit the feed's URL.  It goes through a similar approval process to iTunes.  BlackBerry users must be on BlackBerry 6 OS or download the Podcast App from App World. In my next post, I'll show how to build the podcast feed dynamically from the ID3 tags within the MP3 files.

    Read the article

  • Thread placement policies on NUMA systems - update

    - by Dave
    In a prior blog entry I noted that Solaris used a "maximum dispersal" placement policy to assign nascent threads to their initial processors. The general idea is that threads should be placed as far away from each other as possible in the resource topology in order to reduce resource contention between concurrently running threads. This policy assumes that resource contention -- pipelines, memory channel contention, destructive interference in the shared caches, etc -- will likely outweigh (a) any potential communication benefits we might achieve by packing our threads more densely onto a subset of the NUMA nodes, and (b) benefits of NUMA affinity between memory allocated by one thread and accessed by other threads. We want our threads spread widely over the system and not packed together. Conceptually, when placing a new thread, the kernel picks the least loaded node NUMA node (the node with lowest aggregate load average), and then the least loaded core on that node, etc. Furthermore, the kernel places threads onto resources -- sockets, cores, pipelines, etc -- without regard to the thread's process membership. That is, initial placement is process-agnostic. Keep reading, though. This description is incorrect. On Solaris 10 on a SPARC T5440 with 4 x T2+ NUMA nodes, if the system is otherwise unloaded and we launch a process that creates 20 compute-bound concurrent threads, then typically we'll see a perfect balance with 5 threads on each node. We see similar behavior on an 8-node x86 x4800 system, where each node has 8 cores and each core is 2-way hyperthreaded. So far so good; this behavior seems in agreement with the policy I described in the 1st paragraph. I recently tried the same experiment on a 4-node T4-4 running Solaris 11. Both the T5440 and T4-4 are 4-node systems that expose 256 logical thread contexts. To my surprise, all 20 threads were placed onto just one NUMA node while the other 3 nodes remained completely idle. I checked the usual suspects such as processor sets inadvertently left around by colleagues, processors left offline, and power management policies, but the system was configured normally. I then launched multiple concurrent instances of the process, and, interestingly, all the threads from the 1st process landed on one node, all the threads from the 2nd process landed on another node, and so on. This happened even if I interleaved thread creating between the processes, so I was relatively sure the effect didn't related to thread creation time, but rather that placement was a function of process membership. I this point I consulted the Solaris sources and talked with folks in the Solaris group. The new Solaris 11 behavior is intentional. The kernel is no longer using a simple maximum dispersal policy, and thread placement is process membership-aware. Now, even if other nodes are completely unloaded, the kernel will still try to pack new threads onto the home lgroup (socket) of the primordial thread until the load average of that node reaches 50%, after which it will pick the next least loaded node as the process's new favorite node for placement. On the T4-4 we have 64 logical thread contexts (strands) per socket (lgroup), so if we launch 48 concurrent threads we will find 32 placed on one node and 16 on some other node. If we launch 64 threads we'll find 32 and 32. That means we can end up with our threads clustered on a small subset of the nodes in a way that's quite different that what we've seen on Solaris 10. So we have a policy that allows process-aware packing but reverts to spreading threads onto other nodes if a node becomes too saturated. It turns out this policy was enabled in Solaris 10, but certain bugs suppressed the mixed packing/spreading behavior. There are configuration variables in /etc/system that allow us to dial the affinity between nascent threads and their primordial thread up and down: see lgrp_expand_proc_thresh, specifically. In the OpenSolaris source code the key routine is mpo_update_tunables(). This method reads the /etc/system variables and sets up some global variables that will subsequently be used by the dispatcher, which calls lgrp_choose() in lgrp.c to place nascent threads. Lgrp_expand_proc_thresh controls how loaded an lgroup must be before we'll consider homing a process's threads to another lgroup. Tune this value lower to have it spread your process's threads out more. To recap, the 'new' policy is as follows. Threads from the same process are packed onto a subset of the strands of a socket (50% for T-series). Once that socket reaches the 50% threshold the kernel then picks another preferred socket for that process. Threads from unrelated processes are spread across sockets. More precisely, different processes may have different preferred sockets (lgroups). Beware that I've simplified and elided details for the purposes of explication. The truth is in the code. Remarks: It's worth noting that initial thread placement is just that. If there's a gross imbalance between the load on different nodes then the kernel will migrate threads to achieve a better and more even distribution over the set of available nodes. Once a thread runs and gains some affinity for a node, however, it becomes "stickier" under the assumption that the thread has residual cache residency on that node, and that memory allocated by that thread resides on that node given the default "first-touch" page-level NUMA allocation policy. Exactly how the various policies interact and which have precedence under what circumstances could the topic of a future blog entry. The scheduler is work-conserving. The x4800 mentioned above is an interesting system. Each of the 8 sockets houses an Intel 7500-series processor. Each processor has 3 coherent QPI links and the system is arranged as a glueless 8-socket twisted ladder "mobius" topology. Nodes are either 1 or 2 hops distant over the QPI links. As an aside the mapping of logical CPUIDs to physical resources is rather interesting on Solaris/x4800. On SPARC/Solaris the CPUID layout is strictly geographic, with the highest order bits identifying the socket, the next lower bits identifying the core within that socket, following by the pipeline (if present) and finally the logical thread context ("strand") on the core. But on Solaris on the x4800 the CPUID layout is as follows. [6:6] identifies the hyperthread on a core; bits [5:3] identify the socket, or package in Intel terminology; bits [2:0] identify the core within a socket. Such low-level details should be of interest only if you're binding threads -- a bad idea, the kernel typically handles placement best -- or if you're writing NUMA-aware code that's aware of the ambient placement and makes decisions accordingly. Solaris introduced the so-called critical-threads mechanism, which is expressed by putting a thread into the FX scheduling class at priority 60. The critical-threads mechanism applies to placement on cores, not on sockets, however. That is, it's an intra-socket policy, not an inter-socket policy. Solaris 11 introduces the Power Aware Dispatcher (PAD) which packs threads instead of spreading them out in an attempt to be able to keep sockets or cores at lower power levels. Maximum dispersal may be good for performance but is anathema to power management. PAD is off by default, but power management polices constitute yet another confounding factor with respect to scheduling and dispatching. If your threads communicate heavily -- one thread reads cache lines last written by some other thread -- then the new dense packing policy may improve performance by reducing traffic on the coherent interconnect. On the other hand if your threads in your process communicate rarely, then it's possible the new packing policy might result on contention on shared computing resources. Unfortunately there's no simple litmus test that says whether packing or spreading is optimal in a given situation. The answer varies by system load, application, number of threads, and platform hardware characteristics. Currently we don't have the necessary tools and sensoria to decide at runtime, so we're reduced to an empirical approach where we run trials and try to decide on a placement policy. The situation is quite frustrating. Relatedly, it's often hard to determine just the right level of concurrency to optimize throughput. (Understanding constructive vs destructive interference in the shared caches would be a good start. We could augment the lines with a small tag field indicating which strand last installed or accessed a line. Given that, we could augment the CPU with performance counters for misses where a thread evicts a line it installed vs misses where a thread displaces a line installed by some other thread.)

    Read the article

  • Running Solaris 11 as a control domain on a T2000

    - by jsavit
    There is increased adoption of Oracle Solaris 11, and many customers are deploying it on systems that previously ran Solaris 10. That includes older T1-processor based systems like T1000 and T2000. Even though they are old (from 2005) and don't have the performance of current SPARC servers, they are still functional, stable servers that customers continue to operate. One reason to install Solaris 11 on them is that older machines are attractive for testing OS upgrades before updating current, production systems. Normally this does not present a challenge, because Solaris 11 runs on any T-series or M-series SPARC server. One scenario adds a complication: running Solaris 11 in a control domain on a T1000 or T2000 hosting logical domains. Solaris 11 pre-installed Oracle VM Server for SPARC incompatible with T1 Unlike Solaris 10, Solaris 11 comes with Oracle VM Server for SPARC preinstalled. The ldomsmanager package contains the logical domains manager for Oracle VM Server for SPARC 2.2, which requires a SPARC T2, T2+, T3, or T4 server. It does not work with T1-processor systems, which are only supported by LDoms Manager 1.2 and earlier. The following screenshot shows what happens (bold font) if you try to use Oracle VM Server for SPARC 2.x commands in a Solaris 11 control domain. The commands were issued in a control domain on a T2000 that previously ran Solaris 10. We also display the version of the logical domains manager installed in Solaris 11: root@t2000 psrinfo -vp The physical processor has 4 virtual processors (0-3) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep T SUNW,Sun-Fire-T200 # ldm -V Failed to connect to logical domain manager: Connection refused # pkg info ldomsmanager Name: system/ldoms/ldomsmanager Summary: Logical Domains Manager Description: LDoms Manager - Virtualization for SPARC T-Series Category: System/Virtualization State: Installed Publisher: solaris Version: 2.2.0.0 Build Release: 5.11 Branch: 0.175.0.8.0.3.0 Packaging Date: May 25, 2012 10:20:48 PM Size: 2.86 MB FMRI: pkg://solaris/system/ldoms/[email protected],5.11-0.175.0.8.0.3.0:20120525T222048Z The 2.2 version of the logical domains manager will have to be removed, and 1.2 installed, in order to use this as a control domain. Preparing to change - create a new boot environment Before doing anything else, lets create a new boot environment: # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris NR / 2.14G static 2012-09-25 10:32 # beadm create solaris-1 # beadm activate solaris-1 # beadm list BE Active Mountpoint Space Policy Created -- ------ ---------- ----- ------ ------- solaris N / 4.82M static 2012-09-25 10:32 solaris-1 R - 2.14G static 2012-09-29 11:40 # init 0 Normally an init 6 to reboot would have been sufficient, but in the next step I reset the system anyway in order to put the system in factory default mode for a "clean" domain configuration. Preparing to change - reset to factory default There was a leftover domain configuration on the T2000, so I reset it to the factory install state. Since the ldm command is't working yet, it can't be done from the control domain, so I did it by logging onto to the service processor: $ ssh -X admin@t2000-sc Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved. Oracle Advanced Lights Out Manager CMT v1.7.9 Please login: admin Please Enter password: ******** sc> showhost Sun-Fire-T2000 System Firmware 6.7.10 2010/07/14 16:35 Host flash versions: OBP 4.30.4.b 2010/07/09 13:48 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 sc> bootmode config="factory-default" sc> poweroff Are you sure you want to power off the system [y/n]? y SC Alert: SC Request to Power Off Host. SC Alert: Host system has shut down. sc> poweron SC Alert: Host System has Reset At this point I rebooted into the new Solaris 11 boot environment, and Solaris commands showed it was running on the factory default configuration of a single domain owning all 32 CPUs and 32GB of RAM (that's what it looked like in 2005.) # psrinfo -vp The physical processor has 8 cores and 32 virtual processors (0-31) The core has 4 virtual processors (0-3) The core has 4 virtual processors (4-7) The core has 4 virtual processors (8-11) The core has 4 virtual processors (12-15) The core has 4 virtual processors (16-19) The core has 4 virtual processors (20-23) The core has 4 virtual processors (24-27) The core has 4 virtual processors (28-31) UltraSPARC-T1 (chipid 0, clock 1200 MHz) # prtconf|grep Mem Memory size: 32640 Megabytes Note that the older processor has 4 virtual CPUs per core, while current processors have 8 per core. Remove ldomsmanager 2.2 and install the 1.2 version The Solaris 11 pkg command is now used to remove the 2.2 version that shipped with Solaris 11: # pkg uninstall ldomsmanager Packages to remove: 1 Create boot environment: No Create backup boot environment: No Services to change: 2 PHASE ACTIONS Removal Phase 130/130 PHASE ITEMS Package State Update Phase 1/1 Package Cache Update Phase 1/1 Image State Update Phase 2/2 Finally, LDoms 1.2 installed via its install script, the same way it was done years ago: # unzip LDoms-1_2-Integration-10.zip # cd LDoms-1_2-Integration-10/Install/ # ./install-ldm Welcome to the LDoms installer. You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. ... ... normal install messages omitted ... The Solaris Security Toolkit applies to Solaris 10, and cannot be used in Solaris 11 (in which several things hardened by the Toolkit are already hardened by default), so answer b in the choice below: You are about to install the Logical Domains Manager package that will enable you to create, destroy and control other domains on your system. Given the capabilities of the LDoms domain manager, you can now change the security configuration of this Solaris instance using the Solaris Security Toolkit. Select a security profile from this list: a) Hardened Solaris configuration for LDoms (recommended) b) Standard Solaris configuration c) Your custom-defined Solaris security configuration profile Enter a, b, or c [a]: b ... other install messages omitted for brevity... After install I ensure that the necessary services are enabled, and verify the version of the installed LDoms Manager: # svcs ldmd STATE STIME FMRI online 22:00:36 svc:/ldoms/ldmd:default # svcs vntsd STATE STIME FMRI disabled Aug_19 svc:/ldoms/vntsd:default # ldm -V Logical Domain Manager (v 1.2-debug) Hypervisor control protocol v 1.3 Using Hypervisor MD v 1.1 System PROM: Hypervisor v. 1.7.3. @(#)Hypervisor 1.7.3.c 2010/07/09 15:14\015 OpenBoot v. 4.30.4. @(#)OBP 4.30.4.b 2010/07/09 13:48 Set up control domain and domain services At this point we have a functioning LDoms 1.2 environment that can be configured in the usual fashion. One difference is that LDoms 1.2 behavior had 'delayed configuration mode (as expected) during initial configuration before rebooting the control domain. Another minor difference with a Solaris 11 control domain is that you define virtual switches using the 'vanity name' of the network interface, rather than the hardware driver name as in Solaris 10. # ldm list ------------------------------------------------------------------------------ Notice: the LDom Manager is running in configuration mode. Configuration and resource information is displayed for the configuration under construction; not the current active configuration. The configuration being constructed will only take effect after it is downloaded to the system controller and the host is reset. ------------------------------------------------------------------------------ NAME STATE FLAGS CONS VCPU MEMORY UTIL UPTIME primary active -n-c-- SP 32 32640M 3.2% 4d 2h 50m # ldm add-vdiskserver primary-vds0 primary # ldm add-vconscon port-range=5000-5100 primary-vcc0 primary # ldm add-vswitch net-dev=net0 primary-vsw0 primary # ldm set-mau 2 primary # ldm set-vcpu 8 primary # ldm set-memory 4g primary # ldm add-config initial # ldm list-spconfig factory-default initial [current] That's it, really. After reboot, we are ready to install guest domains. Summary - new wine in old bottles This example shows that (new) Solaris 11 can be installed on (old) T2000 servers and used as a control domain. The main activity is to remove the preinstalled Oracle VM Server for 2.2 and install Logical Domains 1.2 - the last version of LDoms to support T1-processor systems. I tested Solaris 10 and Solaris 11 guest domains running on this server and they worked without any surprises. This is a viable way to get further into Solaris 11 adoption, even on older T-series equipment.

    Read the article

  • Profiling Startup Of VS2012 &ndash; SpeedTrace Profiler

    - by Alois Kraus
    SpeedTrace is a relatively unknown profiler made a company called Ipcas. A single professional license does cost 449€+VAT. For the test I did use SpeedTrace 4.5 which is currently Beta. Although it is cheaper than dotTrace it has by far the most options to influence how profiling does work. First you need to create a tracing project which does configure tracing for one process type. You can start the application directly from the profiler or (much more interesting) it does attach to a specific process when it is started. For this you need to check “Trace the specified …” radio button and enter the process name in the “Process Name of the Trace” edit box. You can even selectively enable tracing for processes with a specific command line. Then you need to activate the trace project by pressing the Activate Project button and you are ready to start VS as usual. If you want to profile the next 10 VS instances that you start you can set the Number of Processes counter to e.g. 10. This is immensely helpful if you are trying to profile only the next 5 started processes. As you can see there are many more tabs which do allow to influence tracing in a much more sophisticated way. SpeedTrace is the only profiler which does not rely entirely on the profiling Api of .NET. Instead it does modify the IL code (instrumentation on the fly) to write tracing information to disc which can later be analyzed. This approach is not only very fast but it does give you unprecedented analysis capabilities. Once the traces are collected they do show up in your workspace where you can open the trace viewer. I do skip the other windows because this view is by far the most useful one. You can sort the methods not only by Wall Clock time but also by CPU consumption and wait time which none of the other products support in their views at the same time. If you want to optimize for CPU consumption sort by CPU time. If you want to find out where most time is spent you need Clock Total time and Clock Waiting. There you can directly see if the method did take long because it did wait on something or it did really execute stuff that did take so long. Once you have found a method you want to drill deeper you can double click on a method to get to the Caller/Callee view which is similar to the JetBrains Method Grid view. But this time you do see much more. In the middle is the clicked method. Above are the methods that call you and below are the methods that you do directly call. Normally you would then start digging deeper to find the end of the chain where the slow method worth optimizing is located. But there is a shortcut. You can press the magic   button to calculate the aggregation of all called methods. This is displayed in the lower left window where you can see each method call and how long it did take. There you can also sort to see if this call stack does only contain methods (e.g. WCF connect calls which you cannot make faster) not worth optimizing. YourKit has a similar feature where it is called Callees List. In the Functions tab you have in the context menu also many other useful analysis options One really outstanding feature is the View Call History Drilldown. When you select this one you get not a sum of all method invocations but a list with the duration of each method call. This is not surprising since SpeedTrace does use tracing to get its timings. There you can get many useful graphs how this method did behave over time. Did it become slower at some point in time or was only the first call slow? The diagrams and the list will tell you that. That is all fine but what should I do when one method call was slow? I want to see from where it was coming from. No problem select the method in the list hit F10 and you get the call stack. This is a life saver if you e.g. search for serialization problems. Today Serializers are used everywhere. You want to find out from where the 5s XmlSerializer.Deserialize call did come from? Hit F10 and you get the call stack which did invoke the 5s Deserialize call. The CPU timeline tab is also useful to find out where long pauses or excessive CPU consumption did happen. Click in the graph to get the Thread Stacks window where you can get a quick overview what all threads were doing at this time. This does look like the Stack Traces feature in YourKit. Only this time you get the last called method first which helps to quickly see what all threads were executing at this moment. YourKit does generate a rather long list which can be hard to go through when you have many threads. The thread list in the middle does not give you call stacks or anything like that but you see which methods were found most often executing code by the profiler which is a good indication for methods consuming most CPU time. This does sound too good to be true? I have not told you the best part yet. The best thing about this profiler is the staff behind it. When I do see a crash or some other odd behavior I send a mail to Ipcas and I do get usually the next day a mail that the problem has been fixed and a download link to the new version. The guys at Ipcas are even so helpful to log in to your machine via a Citrix Client to help you to get started profiling your actual application you want to profile. After a 2h telco I was converted from a hater to a believer of this tool. The fast response time might also have something to do with the fact that they are actively working on 4.5 to get out of the door. But still the support is by far the best I have encountered so far. The only downside is that you should instrument your assemblies including the .NET Framework to get most accurate numbers. You can profile without doing it but then you will see very high JIT times in your process which can severely affect the correctness of the measured timings. If you do not care about exact numbers you can also enable in the main UI in the Data Trace tab logging of method arguments of primitive types. If you need to know what files at which times were opened by your application you can find it out without a debugger. Since SpeedTrace does read huge trace files in its reader you should perhaps use a 64 bit machine to be able to analyze bigger traces as well. The memory consumption of the trace reader is too high for my taste. But they did promise for the next version to come up with something much improved.

    Read the article

  • Windows XP periodically disconnects, reconnects; Windows 7 doesn't

    - by einpoklum
    My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

    Read the article

  • ffmpeg add two audio streams to video

    - by Tossin Hausen
    I tried this: ffmpeg -i /sdcard/video/transcode/video.avi -map 0:0,0 -i /sdcard/video/transcode/first.mp3 -map 1:0,1 -i /sdcard/video/transcode/second.mp3 -map 2:0,2 -acodec copy -vcodec py /sdcard/video/transcode/Output.avi to add two audio streams to one video file. But ffmpeg says the number of mappings should match the number of output streams. What is wrong here? I'm trying to work with an Android build of FFmepg "ffmpeg for android beta". "Does not work" means that this uncommunicative Android build of FFmpeg just stops without giving any error message. The -codec copy option does not work with this build. Now I tried the same set of files with the FFmpeg called command line tool that comes with Ubuntu 10. Something (can't say where it is from). The -codec copy option does not work with this FFmpeg too. Here the complete output: m30x:~/movie/Film$ ffmpeg -i input.avi -i first.mp3 -i second.mp3 -map 0 -map 1 -map 2 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x93cfd10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Input #2, mp3, from 'second.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #2.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Number of stream maps must match number of output streams Merging only one audio stream with the video stream works with Ubuntu and Android version of FFmpeg. Here the complete output: ffmpeg -i input.avi -i first.mp3 -map 0 -map 1 -acodec copy -vcodec copy output.avi FFmpeg version SVN-r0.5.9-4:0.5.9-0ubuntu0.10.04.1, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --extra-version=4:0.5.9-0ubuntu0.10.04.1 --prefix=/usr --enable-avfilter --enable-avfilter-lavf --enable-vdpau --enable-bzlib --enable-libgsm --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvorbis --enable-pthreads --enable-zlib --disable-stripping --disable-vhook --enable-runtime-cpudetect --enable-gpl --enable-postproc --enable-swscale --enable-x11grab --enable-libdc1394 --enable-shared --disable-static libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 libswscale 0. 7. 1 / 0. 7. 1 libpostproc 51. 2. 0 / 51. 2. 0 built on Jun 12 2012 16:27:34, gcc: 4.4.3 [NULL @ 0x9bfad10]looks like this file was encoded with (divx4/(old)xvid/opendivx) -> forcing low_delay flag Seems stream 0 codec frame rate differs from container frame rate: 30000.00 (30000/1) -> 25.00 (25/1) Input #0, avi, from 'input.avi': Duration: 01:30:33.00, start: 0.000000, bitrate: 901 kb/s Stream #0.0: Video: mpeg4, yuv420p, 576x432, 25 tbr, 25 tbn, 30k tbc Input #1, mp3, from 'first.mp3': Duration: 01:30:32.84, start: 0.000000, bitrate: 63 kb/s Stream #1.0: Audio: mp3, 22050 Hz, stereo, s16, 64 kb/s Output #0, avi, to 'output.avi': Stream #0.0: Video: mpeg4, yuv420p, 576x432, q=2-31, 90k tbn, 25 tbc Stream #0.1: Audio: libmp3lame, 22050 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding frame= 6157 fps=6156 q=-1.0 size= 31667kB time=246.28 bitrate=1053.3kbits/s Do you have an idea why it does not work with two audio streams? By the way, ffmpeg -i input_with_first_audio_stream.avi -i second.mp3 -acodec copy -vcodec copy output_two_audio_streams.avi -newaudio works with both versions of ffmpeg that I use, but the first audio stream is played too fast (x10 or more), while the second audio stream is played correct. Many thanks in advance and sorry for my unconventional question and outdated versions of ffmpeg. But I am a lamer and it is not so easy for me to compile from the source (especially for the Android version). I will try to compile an up to date version of ffmpeg with Ubuntu, but I don't have much free time.

    Read the article

  • Increase RGB components every Hour (r), Minute (g), Second (b) for digital clock

    - by TJ Fertterer
    So I am taking my first javascript class (total noob) and one of the assignments is to modify a digital clock by assigning the color red to hours, green minutes, blue to seconds, then increase the respective color component when it changes. I have successfully assigned a decimal color value (ex. "#850000" to each element (hours, minutes, seconds), but my brain is fried trying to figure out how to increase the brightness when hours, minutes, seconds change, i.e. red goes up to "#870000" changing from 1:00:00 pm to 2:00:00 pm. I've searched everywhere with no help on how to successfully do this. Here is what I have so far and any help on this would be greatly appreciated. TJ <script type="text/javascript"> <!-- function updateClock() { var currentTime = new Date(); var currentHours = currentTime.getHours(); var currentMinutes = currentTime.getMinutes(); var currentSeconds = currentTime.getSeconds(); // Pad the minutes with leading zeros, if required currentMinutes = ( currentMinutes < 10 ? "0" : "" ) + currentMinutes; // Pad the seconds with leading zeros, if required currentSeconds = ( currentSeconds < 10 ? "0" : "" ) + currentSeconds; // Choose either "AM" or "PM" as appropriate var timeOfDay = ( currentHours < 12 ) ? "AM" : "PM"; // Convert the hours component to 12-hour format currentHours = ( currentHours > 12 ) ? currentHours - 12 : currentHours; // Convert an hours component if "0" to "12" currentHours = ( currentHours == 0 ) ? 12 : currentHours; // Get hold of the html elements by their ids var hoursElement = document.getElementById("hours"); document.getElementById("hours").style.color = "#850000"; var minutesElement = document.getElementById("minutes"); document.getElementById("minutes").style.color = "#008500"; var secondsElement = document.getElementById("seconds"); document.getElementById("seconds").style.color = "#000085"; var am_pmElement = document.getElementById("am_pm"); // Put the clock sections text into the elements' innerHTML hoursElement.innerHTML = currentHours; minutesElement.innerHTML = currentMinutes; secondsElement.innerHTML = currentSeconds; am_pmElement.innerHTML = timeOfDay; } // --> </script> </head> <body onload="updateClock(); setInterval( 'updateClock()', 1000 )"> <h1 align="center">The JavaScript digital clock</h1> <h2 align="center">Thomas Fertterer - Lab 2</h2> <div id='clock' style="text-align: center"> <span id="hours"></span>: <span id='minutes'></span>: <span id='seconds'></span> <span id='am_pm'></span> </div> </body> </html>

    Read the article

  • Top tweets SOA Partner Community – October 2013

    - by JuergenKress
    Send your tweets @soacommunity #soacommunity and follow us at http://twitter.com/soacommunity Ronald Luttikhuizen ?My latest upload: SOA Made Simple | Introduction to SOA on @slideshare http://www.slideshare.net/rluttikhuizen/soa-made-simple-introduction-to-soa … via @SlideShare OTNArchBeat ?ArchBeat Link-o-Rama for October 4, 2013 #cloud #linux #oaam #soa http://pub.vitrue.com/y4SK Lucas Jellema ?My blog article shows news on the new SOA Suite 12c release - as it was publicly available during #oow13 see: http://technology.amis.nl/2013/09/27/oow13-soa-suite-12c/ … Yogesh Sontakke ?Introducing OER's new Express Workflows - Simplified Lifecycle Management. Blog post: http://bit.ly/16JKHCf @soacommunity #soagovernance SrinivasPadmanabhuni ?"@OTNArchBeat: SOA and User Interfaces - by @soacommunity @HajoNormann @gschmutz @t_winterberg et al #industrialsoa http://pub.vitrue.com/KmOp " SOA Community ?SOA and User-Interfaces http://servicetechmag.com/I76/0913-2 article published part of #industrialSOA at Service Technology Magazine #soacommunity Estafet Limited ?@Estafet win @UKOUG Middleware Partner of the Year 2013 Yogesh Sontakke ?RT @VikasAatOracle: #Oracle #B2B - written by experts #soa #soacommunity #oraclesoa - time to get a copy ! @SOAScott Danilo Schmiedel ?Thanks a lot to Juergen @soacommunity for the super interesting and well-organized Partner Advisory Council yesterday! Such a Great Value! OTNArchBeat ?Case management supporting re-landscaping application portfolios | @leonsmiers http://pub.vitrue.com/MC5j Samantha Searle ?Apply for the #GartnerBPM 2014 Excellence Awards - find out how via this link http://ow.ly/ptaNQ #Gartner #bpm #process #entarch #cio OTNArchBeat ?SOA and User Interfaces - by @soacommunity @hajonormann @gschmutz @t_winterberg et al #industrialsoa http://pub.vitrue.com/KmOp Dain Hansen ?Hybrid #cloud is on the rise, but is the IT department's culture standing in the way? http://add.vc/eJN #CloudIntegration #OracleSOA OTNArchBeat #SOASuite 11g ps6 - Download your log files directly from the Enterprise Manager | @whitehorsenl http://pub.vitrue.com/KrJ2 Whitehorses ?Whiteblog: SOA Suite 11g ps6 - Download your log files directly from the Enterprise Manager (http://goo.gl/2Gqiax ) Rajesh Raheja ?Cloud integration session recap #oow13 http://blog.raastech.com/2013/09/recap-of-real-world-cloud-integration.html?m=1 … Vikas Anand ?@Ahmed_Aboulnaga thanks for the excellent summary and kind words. #oow13 #cloud #oraclesoa http://blog.raastech.com/2013/09/recap-of-real-world-cloud-integration.html?m=1 … Luis Augusto Weir ?REST is also SOA. Check it out http://www.soa4u.co.uk/2013/09/restful-is-also-soa.html?m=1 … #soacommunity Graham ?“@OracleBPM & @soacommunity: 5 Ways to Modernize Applications with BPM #AppAdvantage" #oracleday http://bit.ly/15yC6e3 SOA Community ?#ACED director asked me for BPM references in FSI - ever visited my #SOACommunity workspace? https://beehiveonline.oracle.com/teamcollab/overview/SOA_Community_Workspace … #soacommunity #bpm OracleBlogs ?SOA Community Newsletter September 2013 http://ow.ly/2Aj6oK OTNArchBeat ?OOW13: First glimpses of the new #SOASuite12c | @LucasJellema http://pub.vitrue.com/2YgX sbernhardt ?Just published new blog entry on OOW 2013 wrap up. http://thecattlecrew.wordpress.com/2013/09/30/oracle-open-world-2013-wrap-up/ … #oow13 @OC_WIRE @soacommunity Emiel Paasschens ?Home with family after an overwhelming #OOW week in San Francisco with lot of info & meetings. Special thanx to @OracleBelux & @soacommunity Robert van Mölken ?Had a awesome week at #OOW13 in SF. Highlights were the @soacommunity Wine tour, @OracleBelux meet-ups and @OracleSOA CAB. Thanks to all :) SOA Community ?The place Oracle Fusion middleware comes from - Oracle 200 - TKs office - next Oracle 100 - SOA & BPM #soacommunity pic.twitter.com/qibFOQVbRo Oracle BPM ?5 Ways to Modernize Applications with BPM #AppAdvantage http://pub.vitrue.com/l2dn Simon Haslam ?Ha ha - how did we miss that! RT @lucasjellema: Post conference announcement of a new middleware appliance? #oow13 pic.twitter.com/3NvcjPfjXb OTNArchBeat ?The OTNArchBeat Daily is out! http://paper.li/OTNArchBeat/1329828521 … ? Top stories today via @lucasjellema @myfear @TylerJewell Packt Publishing ?Get 50% off ALL our DRM-free eBooks - this weekend only! Go to http://www.packtpub.com/ and use code BIG50, as often as you like! #BIG50 OracleBlogs ?Global Perspective: ACE Director from EMEA Weighs in on AppAdvantage http://ow.ly/2Afek2 orclateamsoa ?#orclateamsoa Blog: BPM Auditing Demystified - I've heard from a couple of customers recently asking about BPM aud... http://ow.ly/2AfbAn AMIS, Oracle & Java ?Cool #soasuite 12c feature managed file transfer - visit Dave Barry at demo point sr212 #oow #soacommunity pic.twitter.com/gb4HLbUarR SOA Community ?Let us know what was best at #OOW @soacommunity save trip home - thanks for coming to #SF ;-) see you at #OOW2014 pic.twitter.com/xbWXjRapqh Lonneke Dikmans ?Nice @dschmied is talking about the different steps in his project. He starts with explaining the user interface design #oow13 #ux #acm Lonneke Dikmans ?Saving the best for the end: managing knowledge worker processes by @dschmied and Prasen.#oow13 #acm cool stuff: adaptive case management Luis Augusto Weir ?SOA Governance is more than just OER. Requires people, processes and tools. Check it out #SOA #soacommunity http://youtu.be/Ohn06smVKVw Lonneke Dikmans ?“@OracleSOA: #oow Join us for:Enterprise SOA Infrastructure Best Practices Thu 9/26 2:00 PM - 3:00 PM Moscone West - 2020 SOA Community ?Business Process Management (BPM) 11g PS6 Awareness Course http://wp.me/p10C8u-1as Ajay Khanna ?Detect, Analyze, Act - Fast! http://wp.me/p10C8u-1ao via @soacommunity #OracleBPM Simone Geib ?It took a while, but I finally reached 500 followers. Thanks everybody and especially @soacommunity :) SOA Community ?Functional Testing Business Processes In Oracle BPM Suite 11g by Arun Pareek http://wp.me/p10C8u-1aq SOA Community Distribute the September edition of the SOA Community newsletter READ it! Didn't receive it register http://www.oracle.com/goto/emea/soa #soacommunity SOA Community ?Detect, Analyze, Act - Fast! by Ajay Khanna http://wp.me/p10C8u-1ao Robert van Mölken ?Finalised my #OOW presentation #CON8736 and live demo on wednesday 25th at 11:45am. Also giving a short version at the SOA CAB on thursday. Rajesh Raheja ?"The AppAdvantage of Oracle Cloud & On-premises Integration" http://bit.ly/14RYHmZ SOA Community ?Additional new content SOA & BPM Partner Community http://wp.me/p10C8u-1aw Dain Hansen ?Right now #oow13 SOA, BPM - Customer Advisory Boards. 'No tweeting' says @SOASimone. Instagram of funny cats still ok. leonsmiers ?Case Management with Oracle BPM Suite our presentation on #oow13 http://www.slideshare.net/leonsmiers/oracle-open-world-2013-case-management-smiers-kitson … #capgemini @nkitson72 Mark Simpson ?Flextronics reduced cost of processing an invoice to <$1 from $7 due to BPM @OracleBPM #oow13 saving millions. Way less than industry avg. Holger Mueller ?#Siemens Shared Services CIO says that #Fusion #Middleware made the difference for #Oracle over #Workday. #Integration matters. #OOW13 oracleopenworld ?Miss any #oow13 keynotes, or simply want to rewatch? Check out the live streaming site for keynotes on demand: http://pub.vitrue.com/RG4D SOA Community ?Analyze your m2m data and act on it! Big data Pattern matching, fast data & soa #soacommunity #oow pic.twitter.com/48Q1z4ckh7 SOA Community ?Top tweets SOA Partner Community – September 2013 http://wp.me/p10C8u-1cR Simone Geib ?#oraclesoa hands on lab at #oow13 pic.twitter.com/IJJrqXIMiu Danilo Schmiedel #oow13 CON8436: Managing Knowledge Worker Processes. Come & get a free Adaptive Case Management poster @soacommunity pic.twitter.com/FRc2CSyLwb John Sim ?Great job again Jurgen @soacommunity helping bring Ace Community together! Danilo Schmiedel ?Excellent #OracleBPM Adaptive Case Management intro by @heidibuelowBPM and Prasen at the #oow13 demo ground.Last chance today @soacommunity SOA Community ?Thanks to all our #bpm #soa and #weblogic partners for the great middleware business #oow #soacommunity pic.twitter.com/dBwZ8DMHfH Whitehorses ?Thanks @soacommunity for the party tonight. Great to meet product management & see all the talented EMEA middleware specialists. #oow13 Danilo Schmiedel ?Great tool demo from Link Consulting about managing your SOA with OER #oow13 @soacommunity Torsten Winterberg ?“@soacommunity: thanks to @dschmied and @OC_WIRE for making it happen to have our case management poster as printed version hier at #oow13 Ronald Luttikhuizen ?These were the architects involved in the diagram excitement :) just after State of SOA podcast with @OTNArchBeat pic.twitter.com/5B8jIrVTA9 SOA Community ?Tanks to AVIO for the excellent #bpmn poster and the great bpm business - visit then at #OOW & get the poster pic.twitter.com/ebTg9pFY1C Dain Hansen ?Kurian introducing Oracle Platform-as-a-Service developments. #oow13 #OracleCloud pic.twitter.com/evJLTU53rx Bruce Tierney ?API Management "multi-level pie chart" at #oow13 by Oracle's Tim Hall pic.twitter.com/q12OIRdaue Dain Hansen ?This is not your Daddy's BAM @soacommunity: Is this BAM? Very cool in #soasuite 12c get a demo at sr225 pic.twitter.com/EvwqXW9U5j SOA Community ?Is this BAM? Very cool in #soasuite 12c get a demo at sr225 pic.twitter.com/LybHxyF362 SOA Community ?SOA governance by @Yogesh_Sontakke at demo point sr214 many good new features - key for soa projects #oow #soa pic.twitter.com/DFK0ummsK1 SOA Community ?Cool #soasuite 12c feature managed file transfer - visit Dave Barry at demo point sr212 #oow #soacommunity pic.twitter.com/GDKcqDGhCF SOA Community ?Adaptive Case Management demo point at #OOW visit @heidibuelowBPM get a demo and cmmn notation poster #soacommunity pic.twitter.com/T7yEyI7tdn Lonneke Dikmans ?In case you missed it: http://blog.vennster.nl/2013/09/case-management-part-1.html?spref=tw … Lucas Jellema ?SOA Suite news: Cloud Adapters RightNow and SalesForce plus SDK to develop custom cloud adapters (CY13); REST/JSON support in SB/SCA (12c) Oracle SOA ?Cloud Integration and AppAdvantage: Transform your Enterprise #soa #oow13 http://pub.vitrue.com/UfPB Dain Hansen ?Cloud Integration and AppAdvantage: Transform your Enterprise #soa #oow13 http://pub.vitrue.com/4QWA Hajo Normann ?#BigData, eventing & real time #analytics suggest timely next actions in #oracleBPM & #oracleACM; #oow13 #FastData pic.twitter.com/aFVGrTXPqu Mark Simpson ?OEP CQL engine now used in BAM12c for event stream summary computation with temporal and pattern match features to feed dashboards. #oow13 Mark Simpson ?BAM12c virtually a new product. Analytics that senses ahead of time and also compares to historical trends to guide process or case #oow13 Andrejus Baranovskis ?Enabling UI Shell 12c/11g Multitasking Behavior http://fb.me/18l9vxQfA Amit Zavery ?Oracle Fusion Middleware Empowers Business Users, EVP Thomas Kurian's session summary http://onforb.es/18Ta1jf #oow13 #oraclemiddle #oracle Vikas Anand ?#oow13 #oracleopenworld BPM on display at Middleware keynote by Thomas Kurian pic.twitter.com/PMm719S0Ui SOA Community ?BPM composer - business user empowerment #oow #soacommunity #bpmsuite pic.twitter.com/0Qgl6oVh0h SOA Community ?Model your process in BPMN - make is executable and analyze & improve them #oow #soacommunity pic.twitter.com/jkLlObDdoi Bruce Tierney ?@demed and Thomas Kurian talk mobile and cloud at #oow13 pic.twitter.com/bAAeqn5a2V Amit Zavery ?Thomas Kurian showcasing all the new features of Oracle Fusion Middleware #oraclemiddle #oow13 SOA Community ?Demo time cloud adapters in #soasuite at Thomas Kurian keynote. Build and integrate mobile apps in minutes #oow pic.twitter.com/qTnCOJLLwS SOA Community ?Soa suite cloud adapters and mobile apps by @demed at Thomas Kurian keynote #oow #oracle #soacommunity pic.twitter.com/5aMLkNH4Ng Danilo Schmiedel ?First impressions from Oracle Open World 2013 http://wp.me/p2fG8x-77 @soacommunity @OC_WIRE SOA Community ?Good morning SFO let us know if you attend #OOW & #OPN keynote - #soacommunity pic.twitter.com/hzLYGDlRgE Simon Haslam ?Had a very useful @wlscommunity PAC meeting yesterday... & probably the best swag to date! pic.twitter.com/Lqus8ysbp7 Vikas Anand ?Oracle SOA Suite - Team Blog http://bit.ly/18I1Zj7 Rajesh Raheja ?Introducing new Cloud Connectivity Adapters #soa #demopod #oow13. I'll be there Sep 23 & 24 3-6pm to meetup http://bit.ly/18I1Zj7 leonsmiers ?..and again a very successful Oracle SOA/BPM partner council on the eve of #oow13. Thanks Jurgen! @soacommunity pic.twitter.com/aM1LMlb7Yw Vikas Anand ?#oow13 #soa #oep #exalogic Canon Delivers Fast Data with Oracle Event Processing (Oracle SOA Suite) http://bit.ly/1dwPeHb #soacommunity Rolf Scheuch ?The ACM poster is a big success. Great talks and .... I am soon out of posters! #bpmcon #ACM pic.twitter.com/TriaUyXRWK Oracle SOA ?British Telecom Sucess with Oracle B2B #oow #soa #b2b http://pub.vitrue.com/1RWi leonsmiers ?(Oracle) Case Management supporting re-platforming, a pre-read before our presentation at #oow13 http://leonsmiers.blogspot.com/2013/09/case-management-supporting-re.html … #capgemini #yammer SOA & BPM Partner CommunityFor regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Mix Forum Technorati Tags: Twitter,SOA,Oracle BPM,Community,OPN,Jürgen Kress

    Read the article

  • Time Warp

    - by Jesse
    It’s no secret that daylight savings time can wreak havoc on systems that rely heavily on dates. The system I work on is centered around recording dates and times, so naturally my co-workers and I have seen our fair share of date-related bugs. From time to time, however, we come across something that we haven’t seen before. A few weeks ago the following error message started showing up in our logs: “The supplied DateTime represents an invalid time. For example, when the clock is adjusted forward, any time in the period that is skipped is invalid.” This seemed very cryptic, especially since it was coming from areas of our application that are typically only concerned with capturing date-only (no explicit time component) from the user, like reports that take a “start date” and “end date” parameter. For these types of parameters we just leave off the time component when capturing the date values, so midnight is used as a “placeholder” time. How is midnight an “invalid time”? Globalization Is Hard Over the last couple of years our software has been rolled out to users in several countries outside of the United States, including Brazil. Brazil begins and ends daylight savings time at midnight on pre-determined days of the year. On October 16, 2011 at midnight many areas in Brazil began observing daylight savings time at which time their clocks were set forward one hour. This means that at the instant it became midnight on October 16, it actually became 1:00 AM, so any time between 12:00 AM and 12:59:59 AM never actually happened. Because we store all date values in the database in UTC, always adjust any “local” dates provided by a user to UTC before using them as filters in a query. The error we saw was thrown by .NET when trying to convert the Brazilian local time of 2011-10-16 12:00 AM to UTC since that local time never actually existed. We hadn’t experienced this same issue with any of our US customers because the daylight savings time changes in the US occur at 2:00 AM which doesn’t conflict with our “placeholder” time of midnight. Detecting Invalid Times In .NET you might use code similar to the following for converting a local time to UTC: var localDate = new DateTime(2011, 10, 16); //2011-10-16 @ midnight const string timeZoneId = "E. South America Standard Time"; //Windows system timezone Id for "Brasilia" timezone. var localTimeZone = TimeZoneInfo.FindSystemTimeZoneById(timeZoneId); var convertedDate = TimeZoneInfo.ConvertTimeToUtc(localDate, localTimeZone); The code above throws the “invalid time” exception referenced above. We could try to detect whether or not the local time is invalid with something like this: var localDate = new DateTime(2011, 10, 16); //2011-10-16 @ midnight const string timeZoneId = "E. South America Standard Time"; //Windows system timezone Id for "Brasilia" timezone. var localTimeZone = TimeZoneInfo.FindSystemTimeZoneById(timeZoneId); if (localTimeZone.IsInvalidTime(localDate)) localDate = localDate.AddHours(1); var convertedDate = TimeZoneInfo.ConvertTimeToUtc(localDate, localTimeZone); This code works in this particular scenario, but it hardly seems robust. It also does nothing to address the issue that can arise when dealing with the ambiguous times that fall around the end of daylight savings. When we roll the clocks back an hour they record the same hour on the same day twice in a row. To continue on with our Brazil example, on February 19, 2012 at 12:00 AM, it will immediately become February 18, 2012 at 11:00 PM all over again. In this scenario, how should we interpret February 18, 2011 11:30 PM? Enter Noda Time I heard about Noda Time, the .NET port of the Java library Joda Time, a little while back and filed it away in the back of my mind under the “sounds-like-it-might-be-useful-someday” category.  Let’s see how we might deal with the issue of invalid and ambiguous local times using Noda Time (note that as of this writing the samples below will only work using the latest code available from the Noda Time repo on Google Code. The NuGet package version 0.1.0 published 2011-08-19 will incorrectly report unambiguous times as being ambiguous) : var localDateTime = new LocalDateTime(2011, 10, 16, 0, 0); const string timeZoneId = "Brazil/East"; var timezone = DateTimeZone.ForId(timeZoneId); var localDateTimeMaping = timezone.MapLocalDateTime(localDateTime); ZonedDateTime unambiguousLocalDateTime; switch (localDateTimeMaping.Type) { case ZoneLocalMapping.ResultType.Unambiguous: unambiguousLocalDateTime = localDateTimeMaping.UnambiguousMapping; break; case ZoneLocalMapping.ResultType.Ambiguous: unambiguousLocalDateTime = localDateTimeMaping.EarlierMapping; break; case ZoneLocalMapping.ResultType.Skipped: unambiguousLocalDateTime = new ZonedDateTime( localDateTimeMaping.ZoneIntervalAfterTransition.Start, timezone); break; default: throw new InvalidOperationException(string.Format("Unexpected mapping result type: {0}", localDateTimeMaping.Type)); } var convertedDateTime = unambiguousLocalDateTime.ToInstant().ToDateTimeUtc(); Let’s break this sample down: I’m using the Noda Time ‘LocalDateTime’ object to represent the local date and time. I’ve provided the year, month, day, hour, and minute (zeros for the hour and minute here represent midnight). You can think of a ‘LocalDateTime’ as an “invalidated” date and time; there is no information available about the time zone that this date and time belong to, so Noda Time can’t make any guarantees about its ambiguity. The ‘timeZoneId’ in this sample is different than the ones above. In order to use the .NET TimeZoneInfo class we need to provide Windows time zone ids. Noda Time expects an Olson (tz / zoneinfo) time zone identifier and does not currently offer any means of mapping the Windows time zones to their Olson counterparts, though project owner Jon Skeet has said that some sort of mapping will be publicly accessible at some point in the future. I’m making use of the Noda Time ‘DateTimeZone.MapLocalDateTime’ method to disambiguate the original local date time value. This method returns an instance of the Noda Time object ‘ZoneLocalMapping’ containing information about the provided local date time maps to the provided time zone.  The disambiguated local date and time value will be stored in the ‘unambiguousLocalDateTime’ variable as an instance of the Noda Time ‘ZonedDateTime’ object. An instance of this object represents a completely unambiguous point in time and is comprised of a local date and time, a time zone, and an offset from UTC. Instances of ZonedDateTime can only be created from within the Noda Time assembly (the constructor is ‘internal’) to ensure to callers that each instance represents an unambiguous point in time. The value of the ‘unambiguousLocalDateTime’ might vary depending upon the ‘ResultType’ returned by the ‘MapLocalDateTime’ method. There are three possible outcomes: If the provided local date time is unambiguous in the provided time zone I can immediately set the ‘unambiguousLocalDateTime’ variable from the ‘Unambiguous Mapping’ property of the mapping returned by the ‘MapLocalDateTime’ method. If the provided local date time is ambiguous in the provided time zone (i.e. it falls in an hour that was repeated when moving clocks backward from Daylight Savings to Standard Time), I can use the ‘EarlierMapping’ property to get the earlier of the two possible local dates to define the unambiguous local date and time that I need. I could have also opted to use the ‘LaterMapping’ property in this case, or even returned an error and asked the user to specify the proper choice. The important thing to note here is that as the programmer I’ve been forced to deal with what appears to be an ambiguous date and time. If the provided local date time represents a skipped time (i.e. it falls in an hour that was skipped when moving clocks forward from Standard Time to Daylight Savings Time),  I have access to the time intervals that fell immediately before and immediately after the point in time that caused my date to be skipped. In this case I have opted to disambiguate my local date and time by moving it forward to the beginning of the interval immediately following the skipped period. Again, I could opt to use the end of the interval immediately preceding the skipped period, or raise an error depending on the needs of the application. The point of this code is to convert a local date and time to a UTC date and time for use in a SQL Server database, so the final ‘convertedDate’  variable (typed as a plain old .NET DateTime) has its value set from a Noda Time ‘Instant’. An 'Instant’ represents a number of ticks since 1970-01-01 at midnight (Unix epoch) and can easily be converted to a .NET DateTime in the UTC time zone using the ‘ToDateTimeUtc()’ method. This sample is admittedly contrived and could certainly use some refactoring, but I think it captures the general approach needed to take a local date and time and convert it to UTC with Noda Time. At first glance it might seem that Noda Time makes this “simple” code more complicated and verbose because it forces you to explicitly deal with the local date disambiguation, but I feel that the length and complexity of the Noda Time sample is proportionate to the complexity of the problem. Using TimeZoneInfo leaves you susceptible to overlooking ambiguous and skipped times that could result in run-time errors or (even worse) run-time data corruption in the form of a local date and time being adjusted to UTC incorrectly. I should point out that this research is my first look at Noda Time and I know that I’ve only scratched the surface of its full capabilities. I also think it’s safe to say that it’s still beta software for the time being so I’m not rushing out to use it production systems just yet, but I will definitely be tinkering with it more and keeping an eye on it as it progresses.

    Read the article

  • How do i mount my SD Card? I am using ubuntu 10.04

    - by shobhit
    root@shobhit:/media# lsusb Bus 002 Device 017: ID 14cd:125c Super Top Bus 002 Device 003: ID 0c45:6421 Microdia Bus 002 Device 002: ID 8087:0020 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 011: ID 413c:8160 Dell Computer Corp. Bus 001 Device 006: ID 413c:8162 Dell Computer Corp. Bus 001 Device 005: ID 413c:8161 Dell Computer Corp. Bus 001 Device 004: ID 138a:0008 DigitalPersona, Inc Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 002: ID 8087:0020 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lspci -v -nn 00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fbc08000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at fbc07000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a6) (prog-if 01) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=20, subordinate=20, sec-latency=32 Capabilities: [50] Subsystem: Dell Device [1028:0441] 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b0b] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b2f] (rev 06) (prog-if 01) Subsystem: Dell Device [1028:0441] Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 29 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at fbc06000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 06) Subsystem: Dell Device [1028:0441] Flags: medium devsel, IRQ 3 Memory at fbc05000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 3 Memory at fbc04000 (64-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 3 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 12:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4727] (rev 01) Subsystem: Dell Device [1028:0010] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number cb-c0-8b-ff-ff-38-00-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl 13:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 28 I/O ports at e000 [size=256] Memory at d0b04000 (64-bit, prefetchable) [size=4K] Memory at d0b00000 (64-bit, prefetchable) [size=16K] Expansion ROM at fba00000 [disabled] [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 Capabilities: [cc] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03 Kernel driver in use: r8169 Kernel modules: r8169 root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lshw shobhit description: Portable Computer product: Vostro 3500 vendor: Dell Inc. version: A10 serial: FV1L3N1 width: 32 bits capabilities: smbios-2.6 dmi-2.6 smp-1.4 smp configuration: boot=normal chassis=portable cpus=2 uuid=44454C4C-5600-1031-804C-C6C04F334E31 *-core description: Motherboard product: 0G2R51 vendor: Dell Inc. physical id: 0 version: A10 serial: .FV1L3N1.CN7016612H00PW. slot: To Be Filled By O.E.M. *-cpu:0 description: CPU product: Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 slot: CPU 1 size: 1197MHz capacity: 2926MHz width: 64 bits clock: 533MHz capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida arat tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: id=4 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 3MiB capacity: 3MiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 4.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 width: 64 bits capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 width: 64 bits capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 width: 64 bits capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 width: 64 bits capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 width: 64 bits capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 width: 64 bits capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a width: 64 bits capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b width: 64 bits capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c width: 64 bits capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d width: 64 bits capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e width: 64 bits capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f width: 64 bits capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 3GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT112S6TFR8C-H9 vendor: AD80 physical id: 0 serial: 5525C935 slot: DIMM_A size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT125S6TFR8C-H9 vendor: AD80 physical id: 1 serial: 3441D6CA slot: DIMM_B size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A10 (10/25/2010) size: 64KiB capacity: 1984KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 size: 1197MHz capacity: 1197MHz capabilities: vmx ht cpufreq configuration: id=4 *-logicalcpu:0 description: Logical CPU physical id: 4.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 capabilities: logical *-pci description: Host bridge product: Core Processor DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 18 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: msi pm bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:30 memory:fac00000-faffffff memory:c0000000-cfffffff(prefetchable) ioport:f080(size=8) *-communication UNCLAIMED description: Communication controller product: 5 Series/3400 Series Chipset HECI Controller vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc09000-fbc0900f *-usb:0 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fbc08000-fbc083ff *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:22 memory:fbc00000-fbc03fff *-pci:0 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:24 ioport:2000(size=4096) memory:bc000000-bc1fffff memory:bc200000-bc3fffff(prefetchable) *-pci:1 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:25 ioport:3000(size=4096) memory:fbb00000-fbbfffff memory:bc400000-bc5fffff(prefetchable) *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:8b:aa:d8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=10.0.1.50 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbb00000-fbb03fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:26 ioport:e000(size=4096) memory:fba00000-fbafffff ioport:d0b00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 03 serial: 78:2b:cb:cc:0e:2a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:28 ioport:e000(size=256) memory:d0b04000-d0b04fff(prefetchable) memory:d0b00000-d0b03fff(prefetchable) memory:fba00000-fba1ffff(prefetchable) *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:27 ioport:d000(size=4096) memory:fb000000-fb9fffff ioport:d0000000(size=10485760) *-usb:1 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fbc07000-fbc073ff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a6 width: 32 bits clock: 33MHz capabilities: pci bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 06 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 5 Series/3400 Series Chipset 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi1 version: 06 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:29 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fbc06000-fbc067ff *-disk description: ATA Disk product: WDC WD3200BEKT-7 vendor: Western Digital physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WX21AC0W1945 size: 298GiB (320GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=77e3ed41 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: aa69-51c0 size: 98MiB capacity: 100MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-04-03 02:00:15 filesystem=ntfs label=System Reserved state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: 9854ff5c-1dea-a147-84a6-624e758f44b8 size: 48GiB capacity: 48GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-10 13:55:31 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:2 description: Extended partition physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 size: 48GiB capacity: 48GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 1952MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 46GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,barrier=1,data=ordered state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/56AA8094AA807273 version: 3.1 serial: 22a29e8d-56c7-9a4a-adea-528103948f6d size: 200GiB capacity: 200GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-02 20:17:15 filesystem=ntfs modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-cdrom description: DVD-RAM writer product: DVD+-RW TS-L633J vendor: TSSTcorp physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 version: D200 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 06 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fbc05000-fbc050ff ioport:f000(size=32) *-generic UNCLAIMED description: Signal processing controller product: 5 Series/3400 Series Chipset Thermal Subsystem vendor: Intel Corporation physical id: 1f.6 bus info: pci@0000:00:1f.6 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc04000-fbc04fff *-scsi physical id: 2 bus info: usb@2:1.1 logical name: scsi15 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@15:0.0.0 logical name: /dev/sdb I have tried all options like fdisk /dev/sdb , pmount /dev/sdb but nothing is working .Pls guide me

    Read the article

  • Cisco 800 series won't forward port

    - by sam
    Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime service password-encryption no service dhcp ! hostname QUESTMOUNT ! logging buffered 16386 informational logging rate-limit 100 except warnings no logging console no logging monitor enable secret 5 -removed- ! username administrator secret 5 -removed- username manager secret 5 -removed- clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 3:00 aaa new-model ! ! aaa authentication login default local aaa authentication login userlist local aaa authentication ppp default local aaa authorization network grouplist local aaa session-id common ip subnet-zero no ip source-route no ip domain lookup ip domain name quest.local ! ! no ip bootp server ip inspect name firewall tcp ip inspect name firewall udp ip inspect name firewall cuseeme ip inspect name firewall h323 ip inspect name firewall rcmd ip inspect name firewall realaudio ip inspect name firewall streamworks ip inspect name firewall vdolive ip inspect name firewall sqlnet ip inspect name firewall tftp ip inspect name firewall ftp ip inspect name firewall icmp ip inspect name firewall sip ip inspect name firewall fragment maximum 256 timeout 1 ip inspect name firewall netshow ip inspect name firewall rtsp ip inspect name firewall skinny ip inspect name firewall http ip audit notify log ip audit po max-events 100 ip audit name intrusion info list 3 action alarm ip audit name intrusion attack list 3 action alarm drop reset no ftp-server write-enable ! ! ! ! crypto isakmp policy 1 authentication pre-share ! crypto isakmp policy 2 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group staff key 0 qS;,sc:q<skro1^, domain quest.local pool vpnclients acl 106 ! ! crypto ipsec transform-set tr-null-sha esp-null esp-sha-hmac crypto ipsec transform-set tr-des-md5 esp-des esp-md5-hmac crypto ipsec transform-set tr-des-sha esp-des esp-sha-hmac crypto ipsec transform-set tr-3des-sha esp-3des esp-sha-hmac ! crypto dynamic-map vpnusers 1 description Client to Site VPN Users set transform-set tr-des-md5 ! ! crypto map cm-cryptomap client authentication list userlist crypto map cm-cryptomap isakmp authorization list grouplist crypto map cm-cryptomap client configuration address respond crypto map cm-cryptomap 65000 ipsec-isakmp dynamic vpnusers ! ! ! ! interface Ethernet0 ip address 192.168.0.254 255.255.255.0 ip access-group 102 in ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated ip access-group 101 in no ip redirects no ip unreachables ip nat outside ip inspect firewall out ip audit intrusion in encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username -removed- password 7 -removed- ppp ipcp dns request crypto map cm-cryptomap ! ip local pool vpnclients 192.168.99.1 192.168.99.254 ip nat inside source list 105 interface Dialer0 overload ip nat inside source static tcp 192.168.0.2 444 interface Dialer0 444 ip nat inside source static tcp 192.168.0.51 9000 interface Dialer0 9000 ip nat inside source static udp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 25 interface Dialer0 25 ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ip http server no ip http secure-server ! ip access-list logging interval 10 logging 192.168.0.2 access-list 1 remark The local LAN. access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.0.0 access-list 2 remark Where management can be done from. access-list 2 permit 192.168.0.0 0.0.0.255 access-list 3 remark Traffic not to check for intrustion detection. access-list 3 deny 192.168.99.0 0.0.0.255 access-list 3 permit any access-list 101 remark Traffic allowed to enter the router from the Internet access-list 101 permit ip 192.168.99.0 0.0.0.255 192.168.0.0 0.0.0.255 access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit tcp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit tcp host 120.136.2.22 any eq 1433 access-list 101 permit tcp host 123.100.90.58 any eq 1433 access-list 101 permit udp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit udp host 120.136.2.22 any eq 1433 access-list 101 permit udp host 123.100.90.58 any eq 1433 access-list 101 permit tcp any any eq 444 access-list 101 permit tcp any any eq 9000 access-list 101 permit tcp any any eq smtp access-list 101 permit udp any any eq non500-isakmp access-list 101 permit udp any any eq isakmp access-list 101 permit esp any any access-list 101 permit tcp any any eq 1723 access-list 101 permit gre any any access-list 101 permit tcp any any eq 22 access-list 101 permit tcp any any eq telnet access-list 102 remark Traffic allowed to enter the router from the Ethernet access-list 102 permit ip any host 192.168.0.254 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 105 remark Traffic to NAT access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 106 remark User to Site VPN Clients access-list 106 permit ip 192.168.0.0 0.0.0.255 any dialer-list 1 protocol ip permit ! line con 0 no modem enable line aux 0 line vty 0 4 access-class 2 in transport input telnet ssh transport output none ! scheduler max-task-time 5000 ! end any ideas? :)

    Read the article

  • Ubuntu server has slow performance

    - by Rich
    I have a custom built Ubuntu 11.04 server with a 6 disk software RAID 10 primary drive. On it I'm primarily running a PostgreSQL and a few other utilities that stream data from the web. I often find after a few hours of uptime the server starts to lag with all kinds of processes. For example, it may take 10-15 seconds after log-in to get a shell prompt. It might take 5-10 seconds for top to come up. An ls might take a second or two. When I look at top there is almost no CPU usage. There's a fair amount of memory used by the PostgreSQL server but not enough to bleed into swap. I have no idea where to go from here, other than to suspect the RAID10 (I've only ever had software RAID 1's before). Edit: Output from top: top - 11:56:03 up 1:46, 3 users, load average: 0.89, 0.73, 0.72 Tasks: 119 total, 1 running, 118 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.0%sy, 0.0%ni, 93.5%id, 6.2%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 16325596k total, 3478248k used, 12847348k free, 20880k buffers Swap: 19534176k total, 0k used, 19534176k free, 3041992k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1747 woodsp 20 0 109m 10m 4888 S 1 0.1 0:42.70 python 357 root 20 0 0 0 0 S 0 0.0 0:00.40 jbd2/sda3-8 1 root 20 0 24324 2284 1344 S 0 0.0 0:00.84 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.24 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 10 root 20 0 0 0 0 S 0 0.0 0:00.02 ksoftirqd/1 12 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/1 13 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/2 14 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/2:0 15 root 20 0 0 0 0 S 0 0.0 0:00.00 ksoftirqd/2 16 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/2 17 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/3 18 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/3:0 19 root 20 0 0 0 0 S 0 0.0 0:00.02 ksoftirqd/3 20 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/3 21 root 0 -20 0 0 0 S 0 0.0 0:00.00 cpuset 22 root 0 -20 0 0 0 S 0 0.0 0:00.00 khelper 23 root 20 0 0 0 0 S 0 0.0 0:00.00 kdevtmpfs 24 root 0 -20 0 0 0 S 0 0.0 0:00.00 netns 26 root 20 0 0 0 0 S 0 0.0 0:00.00 sync_supers df -h rpsharp@ncp-skookum:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1.8T 549G 1.2T 32% / udev 7.8G 4.0K 7.8G 1% /dev tmpfs 3.2G 492K 3.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.8G 0 7.8G 0% /run/shm /dev/sda2 952M 128K 952M 1% /boot/efi /dev/md0 5.5T 562G 4.7T 11% /usr/local free -m psharp@ncp-skookum:~$ free -m total used free shared buffers cached Mem: 15942 3409 12533 0 20 2983 -/+ buffers/cache: 405 15537 Swap: 19076 0 19076 tail -50 /var/log/syslog Jul 3 06:31:32 ncp-skookum rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="1070" x-info="http://www.rsyslog.com"] rsyslogd was HUPed Jul 3 06:39:01 ncp-skookum CRON[14211]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 06:40:01 ncp-skookum CRON[14223]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:00:01 ncp-skookum CRON[14328]: (woodsp) CMD (/home/woodsp/bin/mail_tweetupdate # email an update) Jul 3 07:00:01 ncp-skookum CRON[14327]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:00:28 ncp-skookum sendmail[14356]: q63E0SoZ014356: from=woodsp, size=2328, class=0, nrcpts=2, msgid=<[email protected]>, relay=woodsp@localhost Jul 3 07:00:29 ncp-skookum sm-mta[14357]: q63E0Si6014357: from=<[email protected]>, size=2569, class=0, nrcpts=2, msgid=<[email protected]>, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Jul 3 07:00:29 ncp-skookum sendmail[14356]: q63E0SoZ014356: to=Spencer Wood <[email protected]>,Martin Lacayo <[email protected]>, ctladdr=woodsp (1004/1005), delay=00:00:01, xdelay=00:00:01, mailer=relay, pri=62328, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (q63E0Si6014357 Message accepted for delivery) Jul 3 07:00:29 ncp-skookum sm-mta[14359]: STARTTLS=client, relay=mx3.stanford.edu., version=TLSv1/SSLv3, verify=FAIL, cipher=DHE-RSA-AES256-SHA, bits=256/256 Jul 3 07:00:29 ncp-skookum sm-mta[14359]: q63E0Si6014357: to=<[email protected]>,<[email protected]>, ctladdr=<[email protected]> (1004/1005), delay=00:00:01, xdelay=00:00:00, mailer=esmtp, pri=152569, relay=mx3.stanford.edu. [171.67.219.73], dsn=2.0.0, stat=Sent (Ok: queued as 8F3505802AC) Jul 3 07:09:08 ncp-skookum CRON[14396]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 07:17:01 ncp-skookum CRON[14438]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jul 3 07:20:01 ncp-skookum CRON[14453]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:39:01 ncp-skookum CRON[14551]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 07:40:01 ncp-skookum CRON[14562]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:00:01 ncp-skookum CRON[14668]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:09:01 ncp-skookum CRON[14724]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 08:17:01 ncp-skookum CRON[14766]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jul 3 08:20:01 ncp-skookum CRON[14781]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:39:01 ncp-skookum CRON[14881]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 08:40:01 ncp-skookum CRON[14892]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Output of hdparm -t /dev/sd{a,b,c,d,e,f} This looks suspicious? /dev/sda: Timing buffered disk reads: 2 MB in 4.84 seconds = 423.39 kB/sec /dev/sdb: Timing buffered disk reads: 420 MB in 3.01 seconds = 139.74 MB/sec /dev/sdc: Timing buffered disk reads: 390 MB in 3.00 seconds = 129.87 MB/sec /dev/sdd: Timing buffered disk reads: 416 MB in 3.00 seconds = 138.51 MB/sec /dev/sde: Timing buffered disk reads: 422 MB in 3.00 seconds = 140.50 MB/sec /dev/sdf: Timing buffered disk reads: 416 MB in 3.01 seconds = 138.26 MB/sec

    Read the article

  • Windows periodically disconnects, reconnects to the network

    - by einpoklum
    My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

    Read the article

  • Cisco ASA: How to route PPPoE-assigned subnet?

    - by Martijn Heemels
    We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

    Read the article

  • MySQL query, 2 similar servers, 2 minute difference in execution times

    - by mr12086
    I had a similar question on stack overflow, but it seems to be more server/mysql setup related than coding. The queries below all execute instantly on our development server where as they can take upto 2 minutes 20 seconds. The query execution time seems to be affected by home ambiguous the LIKE string's are. If they closely match a country that has few matches it will take less time, and if you use something like 'ge' for germany - it will take longer to execute. But this doesn't always work out like that, at times its quite erratic. Sending data appears to be the culprit but why and what does that mean. Also memory on production looks to be quite low (free memory)? Production: Intel Quad Xeon E3-1220 3.1GHz 4GB DDR3 2x 1TB SATA in RAID1 Network speed 100Mb Ubuntu Development Intel Core i3-2100, 2C/4T, 3.10GHz 500 GB SATA - No RAID 4GB DDR3 UPDATE 2 : mysqltuner output: [prod] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.61-0ubuntu0.10.04.1 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 103M (Tables: 180) [--] Data in InnoDB tables: 491M (Tables: 19) [!!] Total fragmented tables: 38 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 77d 4h 6m 1s (53M q [7.968 qps], 14M conn, TX: 87B, RX: 12B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (12K/53M) [OK] Highest usage of available connections: 22% (34/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/10.6M [OK] Key buffer hit rate: 98.7% (162M cached / 2M reads) [OK] Query cache efficiency: 20.7% (7M cached / 36M selects) [!!] Query cache prunes per day: 3934 [OK] Sorts requiring temporary tables: 1% (3K temp sorts / 230K sorts) [!!] Joins performed without indexes: 71068 [OK] Temporary tables created on disk: 24% (3M on disk / 13M total) [OK] Thread cache hit rate: 99% (690 created / 14M connections) [!!] Table cache hit rate: 0% (64 open / 85M opened) [OK] Open file limit used: 12% (128/1K) [OK] Table locks acquired immediately: 99% (16M immediate / 16M locks) [!!] InnoDB data size / buffer pool: 491.9M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) join_buffer_size (> 128.0K, or always use indexes with joins) table_cache (> 64) innodb_buffer_pool_size (>= 491M) [dev] -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.62-0ubuntu0.11.10.1 [!!] Switch to 64-bit OS - MySQL cannot currently use all of your RAM -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 185M (Tables: 632) [--] Data in InnoDB tables: 967M (Tables: 38) [!!] Total fragmented tables: 73 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 2h 26m 9s (5K q [0.058 qps], 1K conn, TX: 4M, RX: 1M) [--] Reads / Writes: 99% / 1% [--] Total buffers: 58.0M global + 2.7M per thread (151 max threads) [OK] Maximum possible memory usage: 463.8M (11% of installed RAM) [OK] Slow queries: 0% (0/5K) [OK] Highest usage of available connections: 1% (2/151) [OK] Key buffer size / total MyISAM indexes: 16.0M/18.6M [OK] Key buffer hit rate: 99.9% (60K cached / 36 reads) [OK] Query cache efficiency: 44.5% (1K cached / 2K selects) [OK] Query cache prunes per day: 0 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 44 sorts) [OK] Temporary tables created on disk: 24% (162 on disk / 666 total) [OK] Thread cache hit rate: 99% (2 created / 1K connections) [!!] Table cache hit rate: 1% (64 open / 4K opened) [OK] Open file limit used: 8% (88/1K) [OK] Table locks acquired immediately: 100% (1K immediate / 1K locks) [!!] InnoDB data size / buffer pool: 967.7M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: table_cache (> 64) innodb_buffer_pool_size (>= 967M) UPDATE 1: When testing the queries listed here there is usually no more than one other query taking place, and usually none. Because production is actually handling apache requests that development gets very few of as it's only myself and 1 other who accesses it - could the 4GB of RAM be getting exhausted by using the single machine for both apache and mysql server? Production: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 24872 MB in 2.00 seconds = 12450.72 MB/sec Timing buffered disk reads: 368 MB in 3.00 seconds = 122.49 MB/sec sudo hdparm -tT /dev/sdb /dev/sdb: Timing cached reads: 24786 MB in 2.00 seconds = 12407.22 MB/sec Timing buffered disk reads: 350 MB in 3.00 seconds = 116.53 MB/sec Server version(mysql + ubuntu versions): 5.1.61-0ubuntu0.10.04.1 Development: sudo hdparm -tT /dev/sda /dev/sda: Timing cached reads: 10632 MB in 2.00 seconds = 5319.40 MB/sec Timing buffered disk reads: 400 MB in 3.01 seconds = 132.85 MB/sec Server version(mysql + ubuntu versions): 5.1.62-0ubuntu0.11.10.1 ORIGINAL DATA : This query is NOT the query in question but is related so ill post it. SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' And the explain plan for the above query is, run on both dev and production produce the same plan. +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ | 1 | SIMPLE | p2 | const | PRIMARY | PRIMARY | 4 | const | 1 | Using index | | 1 | SIMPLE | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | const | 796 | Using where | | 1 | SIMPLE | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using index | | 1 | SIMPLE | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 1 | SIMPLE | f2 | ref | form_project_id | form_project_id | 4 | const | 15 | Using where | | 1 | SIMPLE | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | +----+-------------+-------+--------+----------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+-------------+ This query takes 2 minutes ~20 seconds to execute. The query that is ACTUALLY being run on the server is this one: SELECT COUNT(*) AS num_results FROM (SELECT f.form_question_has_answer_id FROM form_question_has_answer f INNER JOIN project_company_has_user p ON f.form_question_has_answer_user_id = p.project_company_has_user_user_id INNER JOIN company c ON p.project_company_has_user_company_id = c.company_id INNER JOIN project p2 ON p.project_company_has_user_project_id = p2.project_id INNER JOIN user u ON p.project_company_has_user_user_id = u.user_id INNER JOIN form f2 ON p.project_company_has_user_project_id = f2.form_project_id WHERE (f2.form_template_name = 'custom' AND p.project_company_has_user_garbage_collection = 0 AND p.project_company_has_user_project_id = '29') AND (LCASE(c.company_country) LIKE '%ge%' OR LCASE(c.company_country) LIKE '%abcde%') AND f.form_question_has_answer_form_id = '174' GROUP BY f.form_question_has_answer_id;) dctrn_count_query; With explain plans (again same on dev and production): +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | id | select_type | table | type | possible_keys | key | key_len | ref | rows | Extra | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ | 1 | PRIMARY | NULL | NULL | NULL | NULL | NULL | NULL | NULL | Select tables optimized away | | 2 | DERIVED | p2 | const | PRIMARY | PRIMARY | 4 | | 1 | Using index | | 2 | DERIVED | f | ref | form_question_has_answer_form_id,form_question_has_answer_user_id | form_question_has_answer_form_id | 4 | | 797 | Using where | | 2 | DERIVED | p | ref | project_company_has_user_unique_key,project_company_has_user_user_id,project_company_has_user_company_id,project_company_has_user_project_id,project_company_has_user_garbage_collection | project_company_has_user_user_id | 4 | new_klarents.f.form_question_has_answer_user_id | 1 | Using where | | 2 | DERIVED | f2 | ref | form_project_id | form_project_id | 4 | | 15 | Using where | | 2 | DERIVED | c | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_company_id | 1 | Using where | | 2 | DERIVED | u | eq_ref | PRIMARY | PRIMARY | 4 | new_klarents.p.project_company_has_user_user_id | 1 | Using where; Using index | +----+-------------+-------+--------+------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+----------------------------------+---------+----------------------------------------------------+------+------------------------------+ On the production server the information I have is as follows. Upon execution: +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (2 min 14.28 sec) Show profile: +--------------------------------+------------+ | Status | Duration | +--------------------------------+------------+ | starting | 0.000016 | | checking query cache for query | 0.000057 | | Opening tables | 0.004388 | | System lock | 0.000003 | | Table lock | 0.000036 | | init | 0.000030 | | optimizing | 0.000016 | | statistics | 0.000111 | | preparing | 0.000022 | | executing | 0.000004 | | Sorting result | 0.000002 | | Sending data | 136.213836 | | end | 0.000007 | | query end | 0.000002 | | freeing items | 0.004273 | | storing result in query cache | 0.000010 | | logging slow query | 0.000001 | | logging slow query | 0.000002 | | cleaning up | 0.000002 | +--------------------------------+------------+ On development the results are as follows. +-------------+ | num_results | +-------------+ | 3 | +-------------+ 1 row in set (0.08 sec) Again the profile for this query: +--------------------------------+----------+ | Status | Duration | +--------------------------------+----------+ | starting | 0.000022 | | checking query cache for query | 0.000148 | | Opening tables | 0.000025 | | System lock | 0.000008 | | Table lock | 0.000101 | | optimizing | 0.000035 | | statistics | 0.001019 | | preparing | 0.000047 | | executing | 0.000008 | | Sorting result | 0.000005 | | Sending data | 0.086565 | | init | 0.000015 | | optimizing | 0.000006 | | executing | 0.000020 | | end | 0.000004 | | query end | 0.000004 | | freeing items | 0.000028 | | storing result in query cache | 0.000005 | | removing tmp table | 0.000008 | | closing tables | 0.000008 | | logging slow query | 0.000002 | | cleaning up | 0.000005 | +--------------------------------+----------+ If i remove user and/or project innerjoins the query is reduced to 30s. Last bit of information I have: Mysqlserver and Apache are on the same box, there is only one box for production. Production output from top: before & after. top - 15:43:25 up 78 days, 12:11, 4 users, load average: 1.42, 0.99, 0.78 Tasks: 162 total, 2 running, 160 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 50.4%sy, 0.0%ni, 49.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3772580k used, 265288k free, 243704k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207944k cached top - 15:44:31 up 78 days, 12:13, 4 users, load average: 1.94, 1.23, 0.87 Tasks: 160 total, 2 running, 157 sleeping, 0 stopped, 1 zombie Cpu(s): 0.2%us, 50.6%sy, 0.0%ni, 49.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3834300k used, 203568k free, 243736k buffers Swap: 3905528k total, 265384k used, 3640144k free, 1207804k cached But this isn't a good representation of production's normal status so here is a grab of it from today outside of executing the queries. top - 11:04:58 up 79 days, 7:33, 4 users, load average: 0.39, 0.58, 0.76 Tasks: 156 total, 1 running, 155 sleeping, 0 stopped, 0 zombie Cpu(s): 3.3%us, 2.8%sy, 0.0%ni, 93.9%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4037868k total, 3676136k used, 361732k free, 271480k buffers Swap: 3905528k total, 268736k used, 3636792k free, 1063432k cached Development: This one doesn't change during or after. top - 15:47:07 up 110 days, 22:11, 7 users, load average: 0.17, 0.07, 0.06 Tasks: 210 total, 2 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4111972k total, 1821100k used, 2290872k free, 238860k buffers Swap: 4183036k total, 66472k used, 4116564k free, 921072k cached

    Read the article

  • SQLAuthority News – TechEd India – April 12-14, 2010 Bangalore – An Unforgettable Experience – An Op

    - by pinaldave
    TechEd India was one of the largest Technology events in India led by Microsoft. This event was attended by more than 3,000 technology enthusiasts, making it one of the most well-organized events of the year. Though I attempted to attend almost all the technology events here, I have not seen any bigger or better event in Indian subcontinents other than this. There are 21 Technical Tracks at Tech·Ed India 2010 that span more than 745 learning opportunities. I was fortunate enough to be a part of this whole event as a speaker and a delegate, as well. TechEd India Speaker Badge and A Token of Lifetime Hotel Selection I presented three different sessions at TechEd India and was also a part of panel discussion. (The details of the sessions are given at the end of this blog post.) Due to extensive traveling, I stay away from my family occasionally. For this reason, I took my wife – Nupur and daughter Shaivi (8 months old) to the event along with me. We stayed at the same hotel where the event was organized so as to maximize my time bonding with my family and to have more time in networking with technology community, at the same time. The hotel Lalit Ashok is the largest and most luxurious venue one can find in Bangalore, located in the middle of the city. The cost of the hotel was a bit pricey, but looking at all the advantages, I had decided to ask for a booking there. Hotel Lalit Ashok Nupur Dave and Shaivi Dave Arrival Day – DAY 0 – April 11, 2010 I reached the event a day earlier, and that was one wise decision for I was able to relax a bit and go over my presentation for the next day’s course. I am a kind of person who likes to get everything ready ahead of time. I was also able to enjoy a pleasant evening with several Microsoft employees and my family friends. I even checked out the location where I would be doing presentations the next day. I was fortunate enough to meet Bijoy Singhal from Microsoft who helped me out with a few of the logistics issues that occured the day before. I was not aware of the fact that the very next day he was going to be “The Man” of the TechEd 2010 event. Vinod Kumar from Microsoft was really very kind as he talked to me regarding my subsequent session. He gave me some suggestions which were really helpful that I was able to incorporate them during my presentation. Finally, I was able to meet Abhishek Kant from Microsoft; his valuable suggestions and unlimited passion have inspired many people like me to work with the Community. Pradipta from Microsoft was also around, being extremely busy with logistics; however, in those busy times, he did find some good spare time to have a chat with me and the other Community leaders. I also met Harish Ranganathan and Sachin Rathi, both from Microsoft. It was so interesting to listen to both of them talking about SharePoint. I just have no words to express my overwhelmed spirit because of all these passionate young guys - Pradipta,Vinod, Bijoy, Harish, Sachin and Ahishek (of course!). Map of TechEd India 2010 Event Day 1 – April 12, 2010 From morning until night time, today was truly a very busy day for me. I had two presentations and one panel discussion for the day. Needless to say, I had a few meetings to attend as well. The day started with a keynote from S. Somaseger where he announced the launch of Visual Studio 2010. The keynote area was really eye-catching because of the very large, bigger-than- life uniform screen. This was truly one to show. The title music of the keynote was very interesting and it featured Bijoy Singhal as the model. It was interesting to talk to him afterwards, when we laughed at jokes together about his modeling assignment. TechEd India Keynote Opening Featuring Bijoy TechEd India 2010 Keynote – S. Somasegar Time: 11:15pm – 11:45pm Session 1: True Lies of SQL Server – SQL Myth Buster Following the excellent keynote, I had my very first session on the subject of SQL Server Myth Buster. At first, I was a bit nervous as right after the keynote, for this was my very first session and during my presentation I saw lots of Microsoft Product Team members. Well, it really went well and I had a really good discussion with attendees of the session. I felt that a well begin was half-done and my confidence was regained. Right after the session, I met a few of my Community friends and had meaningful discussions with them on many subjects. The abstract of the session is as follows: In this 30-minute demo session, I am going to briefly demonstrate few SQL Server Myths and their resolutions as I back them up with some demo. This demo presentation is a must-attend for all developers and administrators who would come to the event. This is going to be a very quick yet fun session. Pinal Presenting session at TechEd India 2010 Time: 1:00 PM – 2:00 PM Lunch with Somasegar After the session I went to see my daughter, and then I headed right away to the lunch with S. Somasegar – the keynote speaker and senior vice president of the Developer Division at Microsoft. I really thank to Abhishek who made it possible for us. Because of his efforts, all the MVPs had the opportunity to meet such a legendary person and had to talk with them on Microsoft Technology. Though Somasegar is currently holding such a high position in Microsoft, he is very polite and a real gentleman, and how I wish that everybody in industry is like him. Believe me, if you spread love and kindness, then that is what you will receive back. As soon as lunch time was over, I ran to the session hall as my second presentation was about to start. Time: 2:30pm – 3:30pm Session 2: Master Data Services in Microsoft SQL Server 2008 R2 Business Intelligence is a subject which was widely talked about at TechEd. Everybody was interested in this subject, and I did not excuse myself from this great concept as well. I consider myself fortunate as I was presenting on the subject of Master Data Services at TechEd. When I had initially learned this subject, I had a bit of confusion about the usage of this tool. Later on, I decided that I would tackle about how we all developers and DBAs are not able to understand something so simple such as this, and even worst, creating confusion about the technology. During system designing, it is very important to have a reference material or master lookup tables. Well, I talked about the same subject and presented the session keeping that as my center talk. The session went very well and I received lots of interesting questions. I got many compliments for talking about this subject on the real-life scenario. I really thank Rushabh Mehta (CEO, Solid Quality Mentors India) for his supportive suggestions that helped me prepare the slide deck, as well as the subject. Pinal Presenting session at TechEd India 2010 The abstract of the session is as follows: SQL Server Master Data Services will ship with SQL Server 2008 R2 and will improve Microsoft’s platform appeal. This session provides an in-depth demonstration of MDS features and highlights important usage scenarios. Master Data Services enables consistent decision-making process by allowing you to create, manage and propagate changes from a single master view of your business entities. Also, MDS – Master Data-hub which is a vital component, helps ensure the consistency of reporting across systems and deliver faster and more accurate results across the enterprise. We will talk about establishing the basis for a centralized approach to defining, deploying, and managing master data in the enterprise. Pinal Presenting session at TechEd India 2010 The day was still not over for me. I had ran into several friends but we were not able keep our enthusiasm under control about all the rumors saying that SQL Server 2008 R2 was about to be launched tomorrow in the keynote. I then ran to my third and final technical event for the day- a panel discussion with the top technologies of India. Time: 5:00pm – 6:00pm Panel Discussion: Harness the power of Web – SEO and Technical Blogging As I have delivered two technical sessions by this time, I was a bit tired but  not less enthusiastic when I had to talk about Blog and Technology. We discussed many different topics there. I told them that the most important aspect for any blog is its content. We discussed in depth the issues with plagiarism and how to avoid it. Another topic of discussion was how we technology bloggers can create awareness in the Community about what the right kind of blogging is and what morally and technically wrong acts are. A couple of questions were raised about what type of liberty a person can have in terms of writing blogs. Well, it was generically agreed that a blog is mainly a representation of our ideas and thoughts; it should not be governed by external entities. As long as one is writing what they really want to say, but not providing incorrect information or not practicing plagiarism, a blogger should be allowed to express himself. This panel discussion was supposed to be over in an hour, but the interest of the participants was remarkable and so it was extended for 30 minutes more. Finally, we decided to bring to a close the discussion and agreed that we will continue the topic next year. TechEd India Panel Discussion on Web, Technology and SEO Surprisingly, the day was just beginning after doing all of these. By this time, I have almost met all the MVP who arrived at the event, as well as many Microsoft employees. There were lots of Community folks present, too. I decided that I would go to meet several friends from the Community and continue to communicate with me on SQLAuthority.com. I also met Abhishek Baxi and had a good talk with him regarding Win Mobile and Twitter. He also took a very quick video of me wherein I spoke in my mother’s tongue, Gujarati. It was funny that I talked in Gujarati almost all the day, but when I was talking in the interview I could not find the right Gujarati words to speak. I think we all think in English when we think about Technology, so as to address universality. After meeting them, I headed towards the Speakers’ Dinner. Time: 8:00 PM – onwards Speakers Dinner The Speakers’ dinner was indeed a wonderful opportunity for all the speakers to get together and relax. We talked so many different things, from XBOX to Hindi Movies, and from SQL to Samosas. I just could not express how much fun I had. After a long evening, when I returned tmy room and met Shaivi, I just felt instantly relaxed. Kids are really gifts from God. Today was a really long but exciting day. So many things happened in just one day: Visual Studio Lanch, lunch with Somasegar, 2 technical sessions, 1 panel discussion, community leaders meeting, speakers dinner and, last but not leas,t playing with my child! A perfect day! Day 2 – April 13, 2010 Today started with a bang with the excellent keynote by Kamal Hathi who launched SQL Server 2008 R2 in India and demonstrated the power of PowerPivot to all of us. 101 Million Rows in Excel brought lots of applause from the audience. Kamal Hathi Presenting Keynote at TechEd India 2010 The day was a bit easier one for me. I had no sessions today and no events planned. I had a few meetings planned for the second day of the event. I sat in the speaker’s lounge for half a day and met many people there. I attended nearly 9 different meetings today. The subjects of the meetings were very different. Here is a list of the topics of the Community-related meetings: SQL PASS and its involvement in India and subcontinents How to start community blogging Forums and developing aptitude towards technology Ahmedabad/Gandhinagar User Groups and their developments SharePoint and SQL Business Meeting – a client meeting Business Meeting – a potential performance tuning project Business Meeting – Solid Quality Mentors (SolidQ) And family friends Pinal Dave at TechEd India The day passed by so quickly during this meeting. In the evening, I headed to Partners Expo with friends and checked out few of the booths. I really wanted to talk about some of the products, but due to the freebies there was so much crowd that I finally decided to just take the contact details of the partner. I will now start sending them with my queries and, hopefully, I will have my questions answered. Nupur and Shaivi had also one meeting to attend; it was with our family friend Vijay Raj. Vijay is also a person who loves Technology and loves it more than anybody. I see him growing and learning every day, but still remaining as a ‘human’. I believe that if someone acquires as much knowledge as him, that person will become either a computer or cyborg. Here, Vijay is still a kind gentleman and is able to stay as our close family friend. Shaivi was really happy to play with Uncle Vijay. Pinal Dave and Vijay Raj Renuka Prasad, a Microsoft MVP, impressed me with his passion and knowledge of SQL. Every time he gives me credit for his success, I believe that he is very humble. He has way more certifications than me and has worked many more years with SQL compared to me. He is an excellent photographer as well. Most of the photos in this blog post have been taken by him. I told him if ever he wants to do a part time job, he can do the photography very well. Pinal Dave and Renuka Prasad I also met L Srividya from Microsoft, whom I was looking forward to meet. She is a bundle of knowledge that everyone would surely learn a lot from her. I was able to get a few minutes from her and well, I felt confident. She enlightened me with SQL Server BI concepts, domain management and SQL Server security and few other interesting details. I also had a wonderful time talking about SharePoint with fellow Solid Quality Mentor Joy Rathnayake. He is very passionate about SharePoint but when you talk .NET and SQL with him, he is still overwhelmingly knowledgeable. In fact, while talking to him, I figured out that the recent training he delivered was on SQL Server 2008 R2. I told him a joke that it hurts my ego as he is more popular now in SQL training and consulting than me. I am sure all of you agree that working with good people is a gift from God. I am fortunate enough to work with the best of the best Industry experts. It was a great pleasure to hang out with my Community friends – Ahswin Kini, HimaBindu Vejella, Vasudev G, Suprotim Agrawal, Dhananjay, Vikram Pendse, Mahesh Dhola, Mahesh Mitkari,  Manu Zacharia, Shobhan, Hardik Shah, Ashish Mohta, Manan, Subodh Sohani and Sanjay Shetty (of course!) .  (Please let me know if I have met you at the event and forgot your name to list here). Time: 8:00 PM – onwards Community Leaders Dinner After lots of meetings, I headed towards the Community Leaders dinner meeting and met almost all the folks I met in morning. The discussion was almost the same but the real good thing was that we were enjoying it. The food was really good. Nupur was invited in the event, but Shaivi could not come. When Nupur tried to enter the event, she was stopped as Shaivi did not have the pass to enter the dinner. Nupur expressed that Shaivi is only 8 months old and does not eat outside food as well and could not stay by herself at this age, but the door keeper did not agree and asked that without the entry details Shaivi could not go in, but Nupur could. Nupur called me on phone and asked me to help her out. By the time, I was outside; the organizer of the event reached to the door and happily approved Shaivi to join the party. Once in the party, Shaivi had lots of fun meeting so many people. Shaivi Dave and Abhishek Kant Dean Guida (Infragistics President and CEO) and Pinal Dave (SQLAuthority.com) Day 3 – April 14, 2010 Though, it was last day, I was very much excited today as I was about to present my very favorite session. Query Optimization and Performance Tuning is my domain expertise and I make my leaving by consulting and training the same. Today’s session was on the same subject and as an additional twist, another subject about Spatial Database was presented. I was always intrigued with Spatial Database and I have enjoyed learning about it; however, I have never thought about Spatial Indexing before it was decided that I will do this session. I really thank Solid Quality Mentor Dr. Greg Low for his assistance in helping me prepare the slide deck and also review the content. Furthermore, today was really what I call my ‘learning day’ . So far I had not attended any session in TechEd and I felt a bit down for that. Everybody spends their valuable time & money to learn something new and exciting in TechEd and I had not attended a single session at the moment thinking that it was already last day of the event. I did have a plan for the day and I attended two technical sessions before my session of spatial database. I attended 2 sessions of Vinod Kumar. Vinod is a natural storyteller and there was no doubt that his sessions would be jam-packed. People attended his sessions simply because Vinod is syhe speaker. He did not have a single time disappointed audience; he is truly a good speaker. He knows his stuff very well. I personally do not think that in India he can be compared to anyone for SQL. Time: 12:30pm-1:30pm SQL Server Query Optimization, Execution and Debugging Query Performance I really had a fun time attending this session. Vinod made this session very interactive. The entire audience really got into the presentation and started participating in the event. Vinod was presenting a small problem with Query Tuning, which any developer would have encountered and solved with their help in such a fashion that a developer feels he or she have already resolved it. In one question, I was the only one who was ready to answer and Vinod told me in a light tone that I am now allowed to answer it! The audience really found it very amusing. There was a huge crowd around Vinod after the session. Vinod – A master storyteller! Time: 3:45pm-4:45pm Data Recovery / consistency with CheckDB This session was much heavier than the earlier one, and I must say this is my most favorite session I EVER attended in India. In this TechEd I have only attended two sessions, but in my career, I have attended numerous technical sessions not only in India, but all over the world. This session had taken my breath away. One by one, Vinod took the different databases, and started to corrupt them in different ways. Each database has some unique ways to get corrupted. Once that was done, Vinod started to show the DBCC CEHCKDB and demonstrated how it can solve your problem. He finally fixed all the databases with this single tool. I do have a good knowledge of this subject, but let me honestly admit that I have learned a lot from this session. I enjoyed and cheered during this session along with other attendees. I had total satisfaction that, just like everyone, I took advantage of the event and learned something. I am now TECHnically EDucated. Pinal Dave and Vinod Kumar After two very interactive and informative SQL Sessions from Vinod Kumar, the next turn me presenting on Spatial Database and Indexing. I got once again nervous but Vinod told me to stay natural and do my presentation. Well, once I got a huge stage with a total of four projectors and a large crowd, I felt better. Time: 5:00pm-6:00pm Session 3: Developing with SQL Server Spatial and Deep Dive into Spatial Indexing Pinal Presenting session at TechEd India 2010 Pinal Presenting session at TechEd India 2010 I kicked off this session with Michael J Swart‘s beautiful spatial image. This session was the last one for the day but, to my surprise, I had more than 200+ attendees. Slowly, the rain was starting outside and I was worried that the hall would not be full; despite this, there was not a single seat available in the first five minutes of the session. Thanks to all of you for attending my presentation. I had demonstrated the map of world (and India) and quickly explained what  Geographic and Geometry data types in Spatial Database are. This session had interesting story of Indexing and Comparison, as well as how different traditional indexes are from spatial indexing. Pinal Presenting session at TechEd India 2010 Due to the heavy rain during this event, the power went off for about 22 minutes (just an accident – nobodies fault). During these minutes, there were no audio, no video and no light. I continued to address the mass of 200+ people without any audio device and PowerPoint. I must thank the audience because not a single person left from the session. They all stayed in their place, some moved closure to listen to me properly. I noticed that the curiosity and eagerness to learn new things was at the peak even though it was the very last session of the TechEd. Everybody wanted get the maximum knowledge out of this whole event. I was touched by the support from audience. They listened and participated in my session even without any kinds of technology (no ppt, no mike, no AC, nothing). During these 22 minutes, I had completed my theory verbally. Pinal Presenting session at TechEd India 2010 After a while, we got the projector back online and we continued with some exciting demos. Many thanks to Microsoft people who worked energetically in background to get the backup power for project up. I had a very interesting demo wherein I overlaid Bangalore and Hyderabad on the India Map and find their aerial distance between them. After finding the aerial distance, we browsed online and found that SQL Server estimates the exact aerial distance between these two cities, as compared to the factual distance. There was a huge applause from the crowd on the subject that SQL Server takes into the count of the curvature of the earth and finds the precise distances based on details. During the process of finding the distance, I demonstrated a few examples of the indexes where I expressed how one can use those indexes to find these distances and how they can improve the performance of similar query. I also demonstrated few examples wherein we were able to see in which data type the Index is most useful. We finished the demos with a few more internal stuff. Pinal Presenting session at TechEd India 2010 Despite all issues, I was mostly satisfied with my presentation. I think it was the best session I have ever presented at any conference. There was no help from Technology for a while, but I still got lots of appreciation at the end. When we ended the session, the applause from the audience was so loud that for a moment, the rain was not audible. I was truly moved by the dedication of the Technology enthusiasts. Pinal Dave After Presenting session at TechEd India 2010 The abstract of the session is as follows: The Microsoft SQL Server 2008 delivers new spatial data types that enable you to consume, use, and extend location-based data through spatial-enabled applications. Attend this session to learn how to use spatial functionality in next version of SQL Server to build and optimize spatial queries. This session outlines the new geography data type to store geodetic spatial data and perform operations on it, use the new geometry data type to store planar spatial data and perform operations on it, take advantage of new spatial indexes for high performance queries, use the new spatial results tab to quickly and easily view spatial query results directly from within Management Studio, extend spatial data capabilities by building or integrating location-enabled applications through support for spatial standards and specifications and much more. Time: 8:00 PM – onwards Dinner by Sponsors After the lively session during the day, there was another dinner party courtesy of one of the sponsors of TechEd. All the MVPs and several Community leaders were present at the dinner. I would like to express my gratitude to Abhishek Kant for organizing this wonderful event for us. It was a blast and really relaxing in all angles. We all stayed there for a long time and talked about our sweet and unforgettable memories of the event. Pinal Dave and Bijoy Singhal It was really one wonderful event. After writing this much, I say that I have no words to express about how much I enjoyed TechEd. However, it is true that I shared with you only 1% of the total activities I have done at the event. There were so many people I have met, yet were not mentioned here although I wanted to write their names here, too . Anyway, I have learned so many things and up until now, I am not able to get over all the fun I had in this event. Pinal Dave at TechEd India 2010 The Next Days – April 15, 2010 – till today I am still not able to get my mind out of the whole experience I had at TechEd India 2010. It was like a whole Microsoft Family working together to celebrate a happy occasion. TechEd India – Truly An Unforgettable Experience! Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, MVP, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, SQLAuthority News, SQLServer, T SQL, Technology Tagged: TechEd, TechEdIn

    Read the article

  • SQLAuthority News – TechEd India – April 12-14, 2010 Bangalore – An Unforgettable Experience – An Op

    - by pinaldave
    TechEd India was one of the largest Technology events in India led by Microsoft. This event was attended by more than 3,000 technology enthusiasts, making it one of the most well-organized events of the year. Though I attempted to attend almost all the technology events here, I have not seen any bigger or better event in Indian subcontinents other than this. There are 21 Technical Tracks at Tech·Ed India 2010 that span more than 745 learning opportunities. I was fortunate enough to be a part of this whole event as a speaker and a delegate, as well. TechEd India Speaker Badge and A Token of Lifetime Hotel Selection I presented three different sessions at TechEd India and was also a part of panel discussion. (The details of the sessions are given at the end of this blog post.) Due to extensive traveling, I stay away from my family occasionally. For this reason, I took my wife – Nupur and daughter Shaivi (8 months old) to the event along with me. We stayed at the same hotel where the event was organized so as to maximize my time bonding with my family and to have more time in networking with technology community, at the same time. The hotel Lalit Ashok is the largest and most luxurious venue one can find in Bangalore, located in the middle of the city. The cost of the hotel was a bit pricey, but looking at all the advantages, I had decided to ask for a booking there. Hotel Lalit Ashok Nupur Dave and Shaivi Dave Arrival Day – DAY 0 – April 11, 2010 I reached the event a day earlier, and that was one wise decision for I was able to relax a bit and go over my presentation for the next day’s course. I am a kind of person who likes to get everything ready ahead of time. I was also able to enjoy a pleasant evening with several Microsoft employees and my family friends. I even checked out the location where I would be doing presentations the next day. I was fortunate enough to meet Bijoy Singhal from Microsoft who helped me out with a few of the logistics issues that occured the day before. I was not aware of the fact that the very next day he was going to be “The Man” of the TechEd 2010 event. Vinod Kumar from Microsoft was really very kind as he talked to me regarding my subsequent session. He gave me some suggestions which were really helpful that I was able to incorporate them during my presentation. Finally, I was able to meet Abhishek Kant from Microsoft; his valuable suggestions and unlimited passion have inspired many people like me to work with the Community. Pradipta from Microsoft was also around, being extremely busy with logistics; however, in those busy times, he did find some good spare time to have a chat with me and the other Community leaders. I also met Harish Ranganathan and Sachin Rathi, both from Microsoft. It was so interesting to listen to both of them talking about SharePoint. I just have no words to express my overwhelmed spirit because of all these passionate young guys - Pradipta,Vinod, Bijoy, Harish, Sachin and Ahishek (of course!). Map of TechEd India 2010 Event Day 1 – April 12, 2010 From morning until night time, today was truly a very busy day for me. I had two presentations and one panel discussion for the day. Needless to say, I had a few meetings to attend as well. The day started with a keynote from S. Somaseger where he announced the launch of Visual Studio 2010. The keynote area was really eye-catching because of the very large, bigger-than- life uniform screen. This was truly one to show. The title music of the keynote was very interesting and it featured Bijoy Singhal as the model. It was interesting to talk to him afterwards, when we laughed at jokes together about his modeling assignment. TechEd India Keynote Opening Featuring Bijoy TechEd India 2010 Keynote – S. Somasegar Time: 11:15pm – 11:45pm Session 1: True Lies of SQL Server – SQL Myth Buster Following the excellent keynote, I had my very first session on the subject of SQL Server Myth Buster. At first, I was a bit nervous as right after the keynote, for this was my very first session and during my presentation I saw lots of Microsoft Product Team members. Well, it really went well and I had a really good discussion with attendees of the session. I felt that a well begin was half-done and my confidence was regained. Right after the session, I met a few of my Community friends and had meaningful discussions with them on many subjects. The abstract of the session is as follows: In this 30-minute demo session, I am going to briefly demonstrate few SQL Server Myths and their resolutions as I back them up with some demo. This demo presentation is a must-attend for all developers and administrators who would come to the event. This is going to be a very quick yet fun session. Pinal Presenting session at TechEd India 2010 Time: 1:00 PM – 2:00 PM Lunch with Somasegar After the session I went to see my daughter, and then I headed right away to the lunch with S. Somasegar – the keynote speaker and senior vice president of the Developer Division at Microsoft. I really thank to Abhishek who made it possible for us. Because of his efforts, all the MVPs had the opportunity to meet such a legendary person and had to talk with them on Microsoft Technology. Though Somasegar is currently holding such a high position in Microsoft, he is very polite and a real gentleman, and how I wish that everybody in industry is like him. Believe me, if you spread love and kindness, then that is what you will receive back. As soon as lunch time was over, I ran to the session hall as my second presentation was about to start. Time: 2:30pm – 3:30pm Session 2: Master Data Services in Microsoft SQL Server 2008 R2 Business Intelligence is a subject which was widely talked about at TechEd. Everybody was interested in this subject, and I did not excuse myself from this great concept as well. I consider myself fortunate as I was presenting on the subject of Master Data Services at TechEd. When I had initially learned this subject, I had a bit of confusion about the usage of this tool. Later on, I decided that I would tackle about how we all developers and DBAs are not able to understand something so simple such as this, and even worst, creating confusion about the technology. During system designing, it is very important to have a reference material or master lookup tables. Well, I talked about the same subject and presented the session keeping that as my center talk. The session went very well and I received lots of interesting questions. I got many compliments for talking about this subject on the real-life scenario. I really thank Rushabh Mehta (CEO, Solid Quality Mentors India) for his supportive suggestions that helped me prepare the slide deck, as well as the subject. Pinal Presenting session at TechEd India 2010 The abstract of the session is as follows: SQL Server Master Data Services will ship with SQL Server 2008 R2 and will improve Microsoft’s platform appeal. This session provides an in-depth demonstration of MDS features and highlights important usage scenarios. Master Data Services enables consistent decision-making process by allowing you to create, manage and propagate changes from a single master view of your business entities. Also, MDS – Master Data-hub which is a vital component, helps ensure the consistency of reporting across systems and deliver faster and more accurate results across the enterprise. We will talk about establishing the basis for a centralized approach to defining, deploying, and managing master data in the enterprise. Pinal Presenting session at TechEd India 2010 The day was still not over for me. I had ran into several friends but we were not able keep our enthusiasm under control about all the rumors saying that SQL Server 2008 R2 was about to be launched tomorrow in the keynote. I then ran to my third and final technical event for the day- a panel discussion with the top technologies of India. Time: 5:00pm – 6:00pm Panel Discussion: Harness the power of Web – SEO and Technical Blogging As I have delivered two technical sessions by this time, I was a bit tired but  not less enthusiastic when I had to talk about Blog and Technology. We discussed many different topics there. I told them that the most important aspect for any blog is its content. We discussed in depth the issues with plagiarism and how to avoid it. Another topic of discussion was how we technology bloggers can create awareness in the Community about what the right kind of blogging is and what morally and technically wrong acts are. A couple of questions were raised about what type of liberty a person can have in terms of writing blogs. Well, it was generically agreed that a blog is mainly a representation of our ideas and thoughts; it should not be governed by external entities. As long as one is writing what they really want to say, but not providing incorrect information or not practicing plagiarism, a blogger should be allowed to express himself. This panel discussion was supposed to be over in an hour, but the interest of the participants was remarkable and so it was extended for 30 minutes more. Finally, we decided to bring to a close the discussion and agreed that we will continue the topic next year. TechEd India Panel Discussion on Web, Technology and SEO Surprisingly, the day was just beginning after doing all of these. By this time, I have almost met all the MVP who arrived at the event, as well as many Microsoft employees. There were lots of Community folks present, too. I decided that I would go to meet several friends from the Community and continue to communicate with me on SQLAuthority.com. I also met Abhishek Baxi and had a good talk with him regarding Win Mobile and Twitter. He also took a very quick video of me wherein I spoke in my mother’s tongue, Gujarati. It was funny that I talked in Gujarati almost all the day, but when I was talking in the interview I could not find the right Gujarati words to speak. I think we all think in English when we think about Technology, so as to address universality. After meeting them, I headed towards the Speakers’ Dinner. Time: 8:00 PM – onwards Speakers Dinner The Speakers’ dinner was indeed a wonderful opportunity for all the speakers to get together and relax. We talked so many different things, from XBOX to Hindi Movies, and from SQL to Samosas. I just could not express how much fun I had. After a long evening, when I returned tmy room and met Shaivi, I just felt instantly relaxed. Kids are really gifts from God. Today was a really long but exciting day. So many things happened in just one day: Visual Studio Lanch, lunch with Somasegar, 2 technical sessions, 1 panel discussion, community leaders meeting, speakers dinner and, last but not leas,t playing with my child! A perfect day! Day 2 – April 13, 2010 Today started with a bang with the excellent keynote by Kamal Hathi who launched SQL Server 2008 R2 in India and demonstrated the power of PowerPivot to all of us. 101 Million Rows in Excel brought lots of applause from the audience. Kamal Hathi Presenting Keynote at TechEd India 2010 The day was a bit easier one for me. I had no sessions today and no events planned. I had a few meetings planned for the second day of the event. I sat in the speaker’s lounge for half a day and met many people there. I attended nearly 9 different meetings today. The subjects of the meetings were very different. Here is a list of the topics of the Community-related meetings: SQL PASS and its involvement in India and subcontinents How to start community blogging Forums and developing aptitude towards technology Ahmedabad/Gandhinagar User Groups and their developments SharePoint and SQL Business Meeting – a client meeting Business Meeting – a potential performance tuning project Business Meeting – Solid Quality Mentors (SolidQ) And family friends Pinal Dave at TechEd India The day passed by so quickly during this meeting. In the evening, I headed to Partners Expo with friends and checked out few of the booths. I really wanted to talk about some of the products, but due to the freebies there was so much crowd that I finally decided to just take the contact details of the partner. I will now start sending them with my queries and, hopefully, I will have my questions answered. Nupur and Shaivi had also one meeting to attend; it was with our family friend Vijay Raj. Vijay is also a person who loves Technology and loves it more than anybody. I see him growing and learning every day, but still remaining as a ‘human’. I believe that if someone acquires as much knowledge as him, that person will become either a computer or cyborg. Here, Vijay is still a kind gentleman and is able to stay as our close family friend. Shaivi was really happy to play with Uncle Vijay. Pinal Dave and Vijay Raj Renuka Prasad, a Microsoft MVP, impressed me with his passion and knowledge of SQL. Every time he gives me credit for his success, I believe that he is very humble. He has way more certifications than me and has worked many more years with SQL compared to me. He is an excellent photographer as well. Most of the photos in this blog post have been taken by him. I told him if ever he wants to do a part time job, he can do the photography very well. Pinal Dave and Renuka Prasad I also met L Srividya from Microsoft, whom I was looking forward to meet. She is a bundle of knowledge that everyone would surely learn a lot from her. I was able to get a few minutes from her and well, I felt confident. She enlightened me with SQL Server BI concepts, domain management and SQL Server security and few other interesting details. I also had a wonderful time talking about SharePoint with fellow Solid Quality Mentor Joy Rathnayake. He is very passionate about SharePoint but when you talk .NET and SQL with him, he is still overwhelmingly knowledgeable. In fact, while talking to him, I figured out that the recent training he delivered was on SQL Server 2008 R2. I told him a joke that it hurts my ego as he is more popular now in SQL training and consulting than me. I am sure all of you agree that working with good people is a gift from God. I am fortunate enough to work with the best of the best Industry experts. It was a great pleasure to hang out with my Community friends – Ahswin Kini, HimaBindu Vejella, Vasudev G, Suprotim Agrawal, Dhananjay, Vikram Pendse, Mahesh Dhola, Mahesh Mitkari,  Manu Zacharia, Shobhan, Hardik Shah, Ashish Mohta, Manan, Subodh Sohani and Sanjay Shetty (of course!) .  (Please let me know if I have met you at the event and forgot your name to list here). Time: 8:00 PM – onwards Community Leaders Dinner After lots of meetings, I headed towards the Community Leaders dinner meeting and met almost all the folks I met in morning. The discussion was almost the same but the real good thing was that we were enjoying it. The food was really good. Nupur was invited in the event, but Shaivi could not come. When Nupur tried to enter the event, she was stopped as Shaivi did not have the pass to enter the dinner. Nupur expressed that Shaivi is only 8 months old and does not eat outside food as well and could not stay by herself at this age, but the door keeper did not agree and asked that without the entry details Shaivi could not go in, but Nupur could. Nupur called me on phone and asked me to help her out. By the time, I was outside; the organizer of the event reached to the door and happily approved Shaivi to join the party. Once in the party, Shaivi had lots of fun meeting so many people. Shaivi Dave and Abhishek Kant Dean Guida (Infragistics President and CEO) and Pinal Dave (SQLAuthority.com) Day 3 – April 14, 2010 Though, it was last day, I was very much excited today as I was about to present my very favorite session. Query Optimization and Performance Tuning is my domain expertise and I make my leaving by consulting and training the same. Today’s session was on the same subject and as an additional twist, another subject about Spatial Database was presented. I was always intrigued with Spatial Database and I have enjoyed learning about it; however, I have never thought about Spatial Indexing before it was decided that I will do this session. I really thank Solid Quality Mentor Dr. Greg Low for his assistance in helping me prepare the slide deck and also review the content. Furthermore, today was really what I call my ‘learning day’ . So far I had not attended any session in TechEd and I felt a bit down for that. Everybody spends their valuable time & money to learn something new and exciting in TechEd and I had not attended a single session at the moment thinking that it was already last day of the event. I did have a plan for the day and I attended two technical sessions before my session of spatial database. I attended 2 sessions of Vinod Kumar. Vinod is a natural storyteller and there was no doubt that his sessions would be jam-packed. People attended his sessions simply because Vinod is syhe speaker. He did not have a single time disappointed audience; he is truly a good speaker. He knows his stuff very well. I personally do not think that in India he can be compared to anyone for SQL. Time: 12:30pm-1:30pm SQL Server Query Optimization, Execution and Debugging Query Performance I really had a fun time attending this session. Vinod made this session very interactive. The entire audience really got into the presentation and started participating in the event. Vinod was presenting a small problem with Query Tuning, which any developer would have encountered and solved with their help in such a fashion that a developer feels he or she have already resolved it. In one question, I was the only one who was ready to answer and Vinod told me in a light tone that I am now allowed to answer it! The audience really found it very amusing. There was a huge crowd around Vinod after the session. Vinod – A master storyteller! Time: 3:45pm-4:45pm Data Recovery / consistency with CheckDB This session was much heavier than the earlier one, and I must say this is my most favorite session I EVER attended in India. In this TechEd I have only attended two sessions, but in my career, I have attended numerous technical sessions not only in India, but all over the world. This session had taken my breath away. One by one, Vinod took the different databases, and started to corrupt them in different ways. Each database has some unique ways to get corrupted. Once that was done, Vinod started to show the DBCC CEHCKDB and demonstrated how it can solve your problem. He finally fixed all the databases with this single tool. I do have a good knowledge of this subject, but let me honestly admit that I have learned a lot from this session. I enjoyed and cheered during this session along with other attendees. I had total satisfaction that, just like everyone, I took advantage of the event and learned something. I am now TECHnically EDucated. Pinal Dave and Vinod Kumar After two very interactive and informative SQL Sessions from Vinod Kumar, the next turn me presenting on Spatial Database and Indexing. I got once again nervous but Vinod told me to stay natural and do my presentation. Well, once I got a huge stage with a total of four projectors and a large crowd, I felt better. Time: 5:00pm-6:00pm Session 3: Developing with SQL Server Spatial and Deep Dive into Spatial Indexing Pinal Presenting session at TechEd India 2010 Pinal Presenting session at TechEd India 2010 I kicked off this session with Michael J Swart‘s beautiful spatial image. This session was the last one for the day but, to my surprise, I had more than 200+ attendees. Slowly, the rain was starting outside and I was worried that the hall would not be full; despite this, there was not a single seat available in the first five minutes of the session. Thanks to all of you for attending my presentation. I had demonstrated the map of world (and India) and quickly explained what  Geographic and Geometry data types in Spatial Database are. This session had interesting story of Indexing and Comparison, as well as how different traditional indexes are from spatial indexing. Pinal Presenting session at TechEd India 2010 Due to the heavy rain during this event, the power went off for about 22 minutes (just an accident – nobodies fault). During these minutes, there were no audio, no video and no light. I continued to address the mass of 200+ people without any audio device and PowerPoint. I must thank the audience because not a single person left from the session. They all stayed in their place, some moved closure to listen to me properly. I noticed that the curiosity and eagerness to learn new things was at the peak even though it was the very last session of the TechEd. Everybody wanted get the maximum knowledge out of this whole event. I was touched by the support from audience. They listened and participated in my session even without any kinds of technology (no ppt, no mike, no AC, nothing). During these 22 minutes, I had completed my theory verbally. Pinal Presenting session at TechEd India 2010 After a while, we got the projector back online and we continued with some exciting demos. Many thanks to Microsoft people who worked energetically in background to get the backup power for project up. I had a very interesting demo wherein I overlaid Bangalore and Hyderabad on the India Map and find their aerial distance between them. After finding the aerial distance, we browsed online and found that SQL Server estimates the exact aerial distance between these two cities, as compared to the factual distance. There was a huge applause from the crowd on the subject that SQL Server takes into the count of the curvature of the earth and finds the precise distances based on details. During the process of finding the distance, I demonstrated a few examples of the indexes where I expressed how one can use those indexes to find these distances and how they can improve the performance of similar query. I also demonstrated few examples wherein we were able to see in which data type the Index is most useful. We finished the demos with a few more internal stuff. Pinal Presenting session at TechEd India 2010 Despite all issues, I was mostly satisfied with my presentation. I think it was the best session I have ever presented at any conference. There was no help from Technology for a while, but I still got lots of appreciation at the end. When we ended the session, the applause from the audience was so loud that for a moment, the rain was not audible. I was truly moved by the dedication of the Technology enthusiasts. Pinal Dave After Presenting session at TechEd India 2010 The abstract of the session is as follows: The Microsoft SQL Server 2008 delivers new spatial data types that enable you to consume, use, and extend location-based data through spatial-enabled applications. Attend this session to learn how to use spatial functionality in next version of SQL Server to build and optimize spatial queries. This session outlines the new geography data type to store geodetic spatial data and perform operations on it, use the new geometry data type to store planar spatial data and perform operations on it, take advantage of new spatial indexes for high performance queries, use the new spatial results tab to quickly and easily view spatial query results directly from within Management Studio, extend spatial data capabilities by building or integrating location-enabled applications through support for spatial standards and specifications and much more. Time: 8:00 PM – onwards Dinner by Sponsors After the lively session during the day, there was another dinner party courtesy of one of the sponsors of TechEd. All the MVPs and several Community leaders were present at the dinner. I would like to express my gratitude to Abhishek Kant for organizing this wonderful event for us. It was a blast and really relaxing in all angles. We all stayed there for a long time and talked about our sweet and unforgettable memories of the event. Pinal Dave and Bijoy Singhal It was really one wonderful event. After writing this much, I say that I have no words to express about how much I enjoyed TechEd. However, it is true that I shared with you only 1% of the total activities I have done at the event. There were so many people I have met, yet were not mentioned here although I wanted to write their names here, too . Anyway, I have learned so many things and up until now, I am not able to get over all the fun I had in this event. Pinal Dave at TechEd India 2010 The Next Days – April 15, 2010 – till today I am still not able to get my mind out of the whole experience I had at TechEd India 2010. It was like a whole Microsoft Family working together to celebrate a happy occasion. TechEd India – Truly An Unforgettable Experience! Reference : Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, MVP, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, SQLAuthority News, SQLServer, T SQL, Technology Tagged: TechEd, TechEdIn

    Read the article

  • ORA-03113 in code. In addition, TNS-12535 and ORA-03137 in alert file

    - by user1348107
    I've got an exception that contain ORA-03113: (SiPPSS.GetPrintWorkDirectDetail) - ERR:ORA-03113: end-of-file on communication channel Process ID: 7448 Session ID: 30 Serial number: 9802 ?????:12110937 ????:T855 Oracle.DataAccess.Client.OracleException ORA-03113: end-of-file on communication channel Process ID: 7448 Session ID: 30 Serial number: 9802 ?? Oracle.DataAccess.Client.OracleException.HandleErrorHelper(Int32 errCode, OracleConnection conn, IntPtr opsErrCtx, OpoSqlValCtx* pOpoSqlValCtx, Object src, String procedure, Boolean bCheck) ?? Oracle.DataAccess.Client.OracleException.HandleError(Int32 errCode, OracleConnection conn, String procedure, IntPtr opsErrCtx, OpoSqlValCtx* pOpoSqlValCtx, Object src, Boolean bCheck) ?? Oracle.DataAccess.Client.OracleCommand.ExecuteReader(Boolean requery, Boolean fillRequest, CommandBehavior behavior) ?? Oracle.DataAccess.Client.OracleDataAdapter.Fill(DataTable[] dataTables, Int32 startRecord, Int32 maxRecords, IDbCommand command, CommandBehavior behavior) ?? System.Data.Common.DbDataAdapter.Fill(DataTable dataTable) ?? SiPPSS.VSireiMeisaiDsTableAdapters.V_SIREI_MEISAITableAdapter.FillByRunningNoAndProcNo(V_SIREI_MEISAIDataTable dataTable, String RUNNING_NO, String PROC_NO) ?? C:\SVM\trunk\SiPPSSServer\Server\Dao\View\VSireiMeisaiDs.Designer.vb:? 386 ?? SiPPSS.GetPrintWorkDirectDetail.Execute(BLogicParam param) ?? C:\SVM\trunk\SiPPSSServer\Server\BLogic\Screen\Printing\Rprt0701\GetPrintWorkDirectDetail.vb:? 105 In this case, the oracle alert log as beblow: Fatal NI connect error 12170. VERSION INFORMATION: TNS for 64-bit Windows: Version 11.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Windows NT TCP/IP NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Time: 01-11?-2012 13:50:45 Tracing not turned on. Tns error struct: ns main err code: 12535 TNS-12535: TNS: ??????·???????? ns secondary err code: 12560 nt main err code: 505 TNS-00505: ??????????? nt secondary err code: 60 nt OS err code: 0 Client address: (ADDRESS=(PROTOCOL=tcp)(HOST=10.41.102.53)(PORT=1794)) Thu Nov 01 13:54:17 2012 Thread 1 cannot allocate new log, sequence 1880 Private strand flush not complete Current log# 1 seq# 1879 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1880 (LGWR switch) Current log# 2 seq# 1880 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thu Nov 01 13:54:21 2012 Archived Log entry 1118 added for thread 1 sequence 1879 ID 0xe48db805 dest 1: Thu Nov 01 14:40:12 2012 Thread 1 cannot allocate new log, sequence 1881 Private strand flush not complete Current log# 2 seq# 1880 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1881 (LGWR switch) Current log# 3 seq# 1881 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thu Nov 01 14:40:16 2012 Archived Log entry 1119 added for thread 1 sequence 1880 ID 0xe48db805 dest 1: Thu Nov 01 15:27:42 2012 Thread 1 cannot allocate new log, sequence 1882 Private strand flush not complete Current log# 3 seq# 1881 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 advanced to log sequence 1882 (LGWR switch) Current log# 1 seq# 1882 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thu Nov 01 15:27:46 2012 Archived Log entry 1120 added for thread 1 sequence 1881 ID 0xe48db805 dest 1: Thu Nov 01 16:23:48 2012 Thread 1 cannot allocate new log, sequence 1883 Private strand flush not complete Current log# 1 seq# 1882 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1883 (LGWR switch) Current log# 2 seq# 1883 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thu Nov 01 16:23:52 2012 Archived Log entry 1121 added for thread 1 sequence 1882 ID 0xe48db805 dest 1: Thu Nov 01 17:05:50 2012 Thread 1 cannot allocate new log, sequence 1884 Private strand flush not complete Current log# 2 seq# 1883 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1884 (LGWR switch) Current log# 3 seq# 1884 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thu Nov 01 17:05:55 2012 Archived Log entry 1122 added for thread 1 sequence 1883 ID 0xe48db805 dest 1: Thu Nov 01 17:26:52 2012 Fatal NI connect error 12170. VERSION INFORMATION: TNS for 64-bit Windows: Version 11.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Windows NT TCP/IP NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Time: 01-11?-2012 17:26:52 Tracing not turned on. Tns error struct: ns main err code: 12535 TNS-12535: TNS: ??????·???????? ns secondary err code: 12560 nt main err code: 505 TNS-00505: ??????????? nt secondary err code: 60 nt OS err code: 0 Client address: (ADDRESS=(PROTOCOL=tcp)(HOST=10.41.102.62)(PORT=1286)) Thu Nov 01 17:27:16 2012 Fatal NI connect error 12170. VERSION INFORMATION: TNS for 64-bit Windows: Version 11.2.0.1.0 - Production Oracle Bequeath NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Windows NT TCP/IP NT Protocol Adapter for 64-bit Windows: Version 11.2.0.1.0 - Production Time: 01-11?-2012 17:27:16 Tracing not turned on. Tns error struct: ns main err code: 12535 TNS-12535: TNS: ??????·???????? ns secondary err code: 12560 nt main err code: 505 TNS-00505: ??????????? nt secondary err code: 60 nt OS err code: 0 Client address: (ADDRESS=(PROTOCOL=tcp)(HOST=10.41.102.62)(PORT=1285)) Thu Nov 01 18:08:39 2012 Thread 1 advanced to log sequence 1885 (LGWR switch) Current log# 1 seq# 1885 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thu Nov 01 18:08:40 2012 Archived Log entry 1123 added for thread 1 sequence 1884 ID 0xe48db805 dest 1: Thu Nov 01 19:33:21 2012 Thread 1 cannot allocate new log, sequence 1886 Private strand flush not complete Current log# 1 seq# 1885 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1886 (LGWR switch) Current log# 2 seq# 1886 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thu Nov 01 19:33:25 2012 Archived Log entry 1124 added for thread 1 sequence 1885 ID 0xe48db805 dest 1: Thu Nov 01 20:32:25 2012 Thread 1 cannot allocate new log, sequence 1887 Private strand flush not complete Current log# 2 seq# 1886 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1887 (LGWR switch) Current log# 3 seq# 1887 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thu Nov 01 20:32:29 2012 Archived Log entry 1125 added for thread 1 sequence 1886 ID 0xe48db805 dest 1: Thu Nov 01 21:13:07 2012 Thread 1 advanced to log sequence 1888 (LGWR switch) Current log# 1 seq# 1888 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thu Nov 01 21:13:08 2012 Archived Log entry 1126 added for thread 1 sequence 1887 ID 0xe48db805 dest 1: Thu Nov 01 22:00:00 2012 Setting Resource Manager plan SCHEDULER[0x3006]:DEFAULT_MAINTENANCE_PLAN via scheduler window Setting Resource Manager plan DEFAULT_MAINTENANCE_PLAN via parameter Thu Nov 01 22:00:00 2012 Starting background process VKRM Thu Nov 01 22:00:00 2012 VKRM started with pid=32, OS id=4048 Thu Nov 01 22:00:59 2012 Thread 1 cannot allocate new log, sequence 1889 Private strand flush not complete Current log# 1 seq# 1888 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1889 (LGWR switch) Current log# 2 seq# 1889 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thu Nov 01 22:01:03 2012 Archived Log entry 1127 added for thread 1 sequence 1888 ID 0xe48db805 dest 1: Thu Nov 01 22:32:36 2012 Thread 1 advanced to log sequence 1890 (LGWR switch) Current log# 3 seq# 1890 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thu Nov 01 22:32:37 2012 Archived Log entry 1128 added for thread 1 sequence 1889 ID 0xe48db805 dest 1: Thu Nov 01 22:33:18 2012 Errors in file d:\oracle\diag\rdbms\siporex\siporex\trace\siporex_ora_11884.trc (incident=101313): ORA-03137: TTC protocol internal error : [12333] [8] [49] [50] [] [] [] [] Incident details in: d:\oracle\diag\rdbms\siporex\siporex\incident\incdir_101313\siporex_ora_11884_i101313.trc Thu Nov 01 22:33:21 2012 Trace dumping is performing id=[cdmp_20121101223321] Thu Nov 01 22:40:43 2012 Thread 1 cannot allocate new log, sequence 1891 Private strand flush not complete Current log# 3 seq# 1890 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 advanced to log sequence 1891 (LGWR switch) Current log# 1 seq# 1891 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thu Nov 01 22:40:47 2012 Archived Log entry 1129 added for thread 1 sequence 1890 ID 0xe48db805 dest 1: Thu Nov 01 23:47:30 2012 Thread 1 cannot allocate new log, sequence 1892 Private strand flush not complete Current log# 1 seq# 1891 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1892 (LGWR switch) Current log# 2 seq# 1892 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thu Nov 01 23:47:34 2012 Archived Log entry 1130 added for thread 1 sequence 1891 ID 0xe48db805 dest 1: Fri Nov 02 00:49:31 2012 Thread 1 cannot allocate new log, sequence 1893 Private strand flush not complete Current log# 2 seq# 1892 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1893 (LGWR switch) Current log# 3 seq# 1893 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Fri Nov 02 00:49:35 2012 Archived Log entry 1131 added for thread 1 sequence 1892 ID 0xe48db805 dest 1: Fri Nov 02 01:43:12 2012 Thread 1 cannot allocate new log, sequence 1894 Private strand flush not complete Current log# 3 seq# 1893 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 advanced to log sequence 1894 (LGWR switch) Current log# 1 seq# 1894 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Fri Nov 02 01:43:17 2012 Archived Log entry 1132 added for thread 1 sequence 1893 ID 0xe48db805 dest 1: Fri Nov 02 01:52:51 2012 Errors in file d:\oracle\diag\rdbms\siporex\siporex\trace\siporex_ora_6124.trc (incident=101273): ORA-03137: TTC protocol internal error : [12333] [4] [80] [82] [] [] [] [] Incident details in: d:\oracle\diag\rdbms\siporex\siporex\incident\incdir_101273\siporex_ora_6124_i101273.trc Fri Nov 02 01:52:54 2012 Trace dumping is performing id=[cdmp_20121102015254] Fri Nov 02 02:00:00 2012 Clearing Resource Manager plan via parameter Fri Nov 02 02:43:37 2012 Thread 1 cannot allocate new log, sequence 1895 Private strand flush not complete Current log# 1 seq# 1894 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1895 (LGWR switch) Current log# 2 seq# 1895 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Fri Nov 02 02:43:41 2012 Archived Log entry 1133 added for thread 1 sequence 1894 ID 0xe48db805 dest 1: Fri Nov 02 04:46:18 2012 Thread 1 cannot allocate new log, sequence 1896 Private strand flush not complete Current log# 2 seq# 1895 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1896 (LGWR switch) Current log# 3 seq# 1896 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Fri Nov 02 04:46:22 2012 Archived Log entry 1134 added for thread 1 sequence 1895 ID 0xe48db805 dest 1: Fri Nov 02 04:51:41 2012 Errors in file d:\oracle\diag\rdbms\siporex\siporex\trace\siporex_ora_4048.trc (incident=101425): ORA-03137: TTC protocol internal error : [12333] [4] [67] [85] [] [] [] [] Incident details in: d:\oracle\diag\rdbms\siporex\siporex\incident\incdir_101425\siporex_ora_4048_i101425.trc Fri Nov 02 04:51:44 2012 Trace dumping is performing id=[cdmp_20121102045144] Fri Nov 02 05:54:44 2012 Thread 1 cannot allocate new log, sequence 1897 Private strand flush not complete Current log# 3 seq# 1896 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 advanced to log sequence 1897 (LGWR switch) Current log# 1 seq# 1897 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Fri Nov 02 05:54:48 2012 Archived Log entry 1135 added for thread 1 sequence 1896 ID 0xe48db805 dest 1: Fri Nov 02 07:00:34 2012 Thread 1 cannot allocate new log, sequence 1898 Private strand flush not complete Current log# 1 seq# 1897 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1898 (LGWR switch) Current log# 2 seq# 1898 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Fri Nov 02 07:00:38 2012 Archived Log entry 1136 added for thread 1 sequence 1897 ID 0xe48db805 dest 1: Fri Nov 02 08:32:41 2012 Thread 1 cannot allocate new log, sequence 1899 Private strand flush not complete Current log# 2 seq# 1898 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1899 (LGWR switch) Current log# 3 seq# 1899 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Fri Nov 02 08:32:45 2012 Archived Log entry 1137 added for thread 1 sequence 1898 ID 0xe48db805 dest 1: Fri Nov 02 09:48:57 2012 Thread 1 advanced to log sequence 1900 (LGWR switch) Current log# 1 seq# 1900 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Fri Nov 02 09:48:58 2012 Archived Log entry 1138 added for thread 1 sequence 1899 ID 0xe48db805 dest 1: Fri Nov 02 10:18:15 2012 Thread 1 cannot allocate new log, sequence 1901 Private strand flush not complete Current log# 1 seq# 1900 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1901 (LGWR switch) Current log# 2 seq# 1901 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Fri Nov 02 10:18:19 2012 Archived Log entry 1139 added for thread 1 sequence 1900 ID 0xe48db805 dest 1: Fri Nov 02 10:22:58 2012 Thread 1 cannot allocate new log, sequence 1902 Private strand flush not complete Current log# 2 seq# 1901 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Thread 1 advanced to log sequence 1902 (LGWR switch) Current log# 3 seq# 1902 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Fri Nov 02 10:23:02 2012 Archived Log entry 1140 added for thread 1 sequence 1901 ID 0xe48db805 dest 1: Fri Nov 02 10:27:38 2012 Thread 1 cannot allocate new log, sequence 1903 Checkpoint not complete Current log# 3 seq# 1902 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 cannot allocate new log, sequence 1903 Private strand flush not complete Current log# 3 seq# 1902 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO03.LOG Thread 1 advanced to log sequence 1903 (LGWR switch) Current log# 1 seq# 1903 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Fri Nov 02 10:27:45 2012 Archived Log entry 1141 added for thread 1 sequence 1902 ID 0xe48db805 dest 1: Fri Nov 02 10:32:27 2012 Thread 1 cannot allocate new log, sequence 1904 Checkpoint not complete Current log# 1 seq# 1903 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 cannot allocate new log, sequence 1904 Private strand flush not complete Current log# 1 seq# 1903 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO01.LOG Thread 1 advanced to log sequence 1904 (LGWR switch) Current log# 2 seq# 1904 mem# 0: D:\ORACLE\ORADATA\SIPOREX\REDO02.LOG Fri Nov 02 10:32:34 2012 Archived Log entry 1142 added for thread 1 sequence 1903 ID 0xe48db805 dest 1: Fri Nov 02 10:35:42 2012 Errors in file d:\oracle\diag\rdbms\siporex\siporex\trace\siporex_ora_15856.trc (incident=101353): ORA-03137: TTC protocol internal error : [12333] [8] [49] [50] [] [] [] [] Incident details in: d:\oracle\diag\rdbms\siporex\siporex\incident\incdir_101353\siporex_ora_15856_i101353.trc Fri Nov 02 10:35:44 2012 Trace dumping is performing id=[cdmp_20121102103544] I don't know main reason of this issue as well as how to fixing it. Please help me.

    Read the article

  • Google Maps API v3 - Different markers/labels on different zoom levels

    - by krikara
    I was wondering if it is possible that Google has a feature to view different markers on different zoom levels. For example, on zoom level 1, I want one marker over China with the label saying "5". And as the user zooms in, lets say on zoom level 4, I want the previous marker and label to disappear. And I want to have 5 new markers/labels, each on a different city in China all saying "1". Thus China will say a number and all the cities in China will say numbers adding up to China's number. The key concept I am trying to figure out here is how to hide markers and labels based on zoom levels. A constraint for me is that I am living in China currently where google is censored, so a lot of online documents are censored for me, including many of google's documentations. Here is my code thus far <!DOCTYPE html> <html> <head> <meta name="viewport" content="initial-scale=1.0, user-scalable=no" /> <title>TM China</title> <style type="text/css"> html, body, #map_canvas { margin: 0; padding: 0; height: 100% } .labels { color: red; background-color: white; font-family: "Lucida Grande", "Arial", sans-serif; font-size: 10px; font-weight: bold; text-align: center; width: 60px; border: 2px solid black; white-space: nowrap; } </style> <script type="text/javascript" src="http://maps.googleapis.com/maps/api/js?key=AIzaSyDV0lcdK7C2GHbQAmdkBID70Uppuf-D030&sensor=true"> </script> <script type="text/javascript"> eval(function(p,a,c,k,e,r){e=function(c){return(c<a?'':e(parseInt(c/a)))+((c=c%a)>35?String.fromCharCode(c+29):c.toString(36))};if(!''.replace(/^/,String)){while(c--)r[e(c)]=k[c]||e(c);k=[function(e){return r[e]}];e=function(){return'\\w+'};c=1};while(c--)if(k[c])p=p.replace(new RegExp('\\b'+e(c)+'\\b','g'),k[c]);return p}('7 m(a){2.3=a;2.8=V.1E("1u");2.8.4.C="I: 1m; J: 1g;";2.k=V.1E("1u");2.k.4.C=2.8.4.C}m.l=E 6.5.22();m.l.1Y=7(){n c=2;n h=t;n f=t;n j;n b;n d,K;n i;n g=7(e){p(e.1v){e.1v()}e.2b=u;p(e.1t){e.1t()}};2.1s().24.G(2.8);2.1s().20.G(2.k);2.11=[6.5.9.w(V,"1o",7(a){p(f){a.s=j;i=u;6.5.9.r(c.3,"1n",a)}h=t;6.5.9.r(c.3,"1o",a)}),6.5.9.o(c.3.1P(),"1N",7(a){p(h&&c.3.1M()){a.s=E 6.5.1J(a.s.U()-d,a.s.T()-K);j=a.s;p(f){6.5.9.r(c.3,"1i",a)}F{d=a.s.U()-c.3.Z().U();K=a.s.T()-c.3.Z().T();6.5.9.r(c.3,"1e",a)}}}),6.5.9.w(2.k,"1d",7(e){c.k.4.1c="2i";6.5.9.r(c.3,"1d",e)}),6.5.9.w(2.k,"1D",7(e){c.k.4.1c=c.3.2g();6.5.9.r(c.3,"1D",e)}),6.5.9.w(2.k,"1C",7(e){p(i){i=t}F{g(e);6.5.9.r(c.3,"1C",e)}}),6.5.9.w(2.k,"1A",7(e){g(e);6.5.9.r(c.3,"1A",e)}),6.5.9.w(2.k,"1z",7(e){h=u;f=t;d=0;K=0;g(e);6.5.9.r(c.3,"1z",e)}),6.5.9.o(2.3,"1e",7(a){f=u;b=c.3.1b()}),6.5.9.o(2.3,"1i",7(a){c.3.O(a.s);c.3.D(2a)}),6.5.9.o(2.3,"1n",7(a){f=t;c.3.D(b)}),6.5.9.o(2.3,"29",7(){c.O()}),6.5.9.o(2.3,"28",7(){c.D()}),6.5.9.o(2.3,"27",7(){c.N()}),6.5.9.o(2.3,"26",7(){c.N()}),6.5.9.o(2.3,"25",7(){c.16()}),6.5.9.o(2.3,"23",7(){c.15()}),6.5.9.o(2.3,"21",7(){c.13()}),6.5.9.o(2.3,"1Z",7(){c.L()}),6.5.9.o(2.3,"1X",7(){c.L()})]};m.l.1W=7(){n i;2.8.1r.1q(2.8);2.k.1r.1q(2.k);1p(i=0;i<2.11.1V;i++){6.5.9.1U(2.11[i])}};m.l.1T=7(){2.15();2.16();2.L()};m.l.15=7(){n a=2.3.z("Y");p(H a.1S==="P"){2.8.W=a;2.k.W=2.8.W}F{2.8.G(a);a=a.1R(u);2.k.G(a)}};m.l.16=7(){2.k.1Q=2.3.1O()||""};m.l.L=7(){n i,q;2.8.S=2.3.z("R");2.k.S=2.8.S;2.8.4.C="";2.k.4.C="";q=2.3.z("q");1p(i 1L q){p(q.1K(i)){2.8.4[i]=q[i];2.k.4[i]=q[i]}}2.1l()};m.l.1l=7(){2.8.4.I="1m";2.8.4.J="1g";p(H 2.8.4.B!=="P"){2.8.4.1k="1j(B="+(2.8.4.B*1I)+")"}2.k.4.I=2.8.4.I;2.k.4.J=2.8.4.J;2.k.4.B=0.1H;2.k.4.1k="1j(B=1)";2.13();2.O();2.N()};m.l.13=7(){n a=2.3.z("X");2.8.4.1h=-a.x+"v";2.8.4.1f=-a.y+"v";2.k.4.1h=-a.x+"v";2.k.4.1f=-a.y+"v"};m.l.O=7(){n a=2.1G().1F(2.3.Z());2.8.4.12=a.x+"v";2.8.4.M=a.y+"v";2.k.4.12=2.8.4.12;2.k.4.M=2.8.4.M;2.D()};m.l.D=7(){n a=(2.3.z("14")?-1:+1);p(H 2.3.1b()==="P"){2.8.4.A=2h(2.8.4.M,10)+a;2.k.4.A=2.8.4.A}F{2.8.4.A=2.3.1b()+a;2.k.4.A=2.8.4.A}};m.l.N=7(){p(2.3.z("1a")){2.8.4.Q=2.3.2f()?"2e":"1B"}F{2.8.4.Q="1B"}2.k.4.Q=2.8.4.Q};7 19(a){a=a||{};a.Y=a.Y||"";a.X=a.X||E 6.5.2d(0,0);a.R=a.R||"2c";a.q=a.q||{};a.14=a.14||t;p(H a.1a==="P"){a.1a=u}2.1y=E m(2);6.5.18.1x(2,1w)}19.l=E 6.5.18();19.l.17=7(a){6.5.18.l.17.1x(2,1w);2.1y.17(a)};',62,143,'||this|marker_|style|maps|google|function|labelDiv_|event|||||||||||eventDiv_|prototype|MarkerLabel_|var|addListener|if|labelStyle|trigger|latLng|false|true|px|addDomListener|||get|zIndex|opacity|cssText|setZIndex|new|else|appendChild|typeof|position|overflow|cLngOffset|setStyles|top|setVisible|setPosition|undefined|display|labelClass|className|lng|lat|document|innerHTML|labelAnchor|labelContent|getPosition||listeners_|left|setAnchor|labelInBackground|setContent|setTitle|setMap|Marker|MarkerWithLabel|labelVisible|getZIndex|cursor|mouseover|dragstart|marginTop|hidden|marginLeft|drag|alpha|filter|setMandatoryStyles|absolute|dragend|mouseup|for|removeChild|parentNode|getPanes|stopPropagation|div|preventDefault|arguments|apply|label|mousedown|dblclick|none|click|mouseout|createElement|fromLatLngToDivPixel|getProjection|01|100|LatLng|hasOwnProperty|in|getDraggable|mousemove|getTitle|getMap|title|cloneNode|nodeType|draw|removeListener|length|onRemove|labelstyle_changed|onAdd|labelclass_changed|overlayMouseTarget|labelanchor_changed|OverlayView|labelcontent_changed|overlayImage|title_changed|labelvisible_changed|visible_changed|zindex_changed|position_changed|1000000|cancelBubble|markerLabels|Point|block|getVisible|getCursor|parseInt|pointer'.split('|'),0,{})) var map; var mapOptions = { center: new google.maps.LatLng(35, 105), zoom: 3, mapTypeId: google.maps.MapTypeId.ROADMAP }; var locations = [ ['Hong Kong', 22.39, 114.10, 1885], ['Shanghai', 31.232, 121.47, 5885], ['Beijing', 39.88, 116.40, 6426], ['Guangzhou', 23.129, 113.264, 4067], ['Shenzhen', 22.54, 114.05, 3089], ['Hangzhou', 30.27, 120.15, 954] ]; var infowindow = new google.maps.InfoWindow(); var i; /* for (i = 0; i < locations.length; i++) { marker = new google.maps.Marker({ position: new google.maps.LatLng(locations[i][1], locations[i][2]), map: map }); google.maps.event.addListener(marker, 'click', (function(marker, i) { return function() { infowindow.setContent(locations[i][0]); infowindow.open(map, marker); } })(marker, i)); } */ function myMarker(options) { if(!options.labelAnchor) { options.labelAnchor = new google.maps.Point(30, 50); } if(!options.labelClass) { options.labelClass = "labels"; } options.map = map; return new MarkerWithLabel(options); } function initialize() { map = new google.maps.Map(document.getElementById("map_canvas"), mapOptions); for (i = 0; i < locations.length; i++) { var marker = new MarkerWithLabel({ position: new google.maps.LatLng(locations[i][1], locations[i][2]), draggable: false, map: map, labelContent: locations[i][3], labelAnchor: new google.maps.Point(30, 0), labelClass: "labels", // the CSS class for the label labelStyle: {opacity: 0.75} }); } /* var marker2 = new myMarker({ position: new google.maps.LatLng(20,20), draggable: true, labelContent: "second" }); */ } google.maps.event.addDomListener(window, 'load', initialize); </script> </head> <body onload="initialize()"> <div id="map_canvas" style="width:85%; height:85%"></div> <script type="text/javascript"> </script> </body> </html> EDIT I have been trying to experiment with the MarkerManager, but I can't get the markers to create successfully on different zoom levels. First, I changed my default zoom level to 1, and then I changed my code to what is shown below. function initialize() { map = new google.maps.Map(document.getElementById("map_canvas"), mapOptions); /* for (i = 0; i < locations.length; i++) { var marker = new MarkerWithLabel({ position: new google.maps.LatLng(locations[i][1], locations[i][2]), draggable: false, map: map, labelContent: locations[i][3], labelAnchor: new google.maps.Point(30, 0), labelClass: "labels", // the CSS class for the label labelStyle: {opacity: 0.75} }); } */ var listener = google.maps.event.addListener(map, 'bounds_changed', function(){ setupMarkers(); google.maps.event.removeListener(listener); }); } function createCityMarkers() { for (i = 0; i < locations.length; i++) { var marker = new MarkerWithLabel({ position: new google.maps.LatLng(locations[i][1], locations[i][2]), draggable: false, map: map, labelContent: locations[i][3], labelAnchor: new google.maps.Point(30, 0), labelClass: "labels", // the CSS class for the label labelStyle: {opacity: 0.75} }); } } function setupMarkers() { mgr = new MarkerManager(map); google.maps.event.addListener(mgr, 'loaded', function(){ mgr.addMarkers(createCityMarkers(), 4); mgr.refresh(); }); } I have also tried applying the source code of this link as well, but nothing is working out. And when I copy the source code directly to my computer and replace all the icons with markers, the markers still don't appear. I can't seem to figure how to make markers appear using the marker Manager. http://google-maps-utility-library-v3.googlecode.com/svn/tags/markermanager/1.0/examples/weather_map.html

    Read the article

  • WMI Remote Process Starting

    - by Goober
    Scenario I've written a WMI Wrapper that seems to be quite sufficient, however whenever I run the code to start a remote process on a server, I see the process name appear in the task manager but the process itself does not start like it should (as in, I don't see the command line log window of the process that prints out what it's doing etc.) The process I am trying to start is just a C# application executable that I have written. Below is my WMI Wrapper Code and the code I am using to start running the process. Question Is the process actually running? - Even if it is only displaying the process name in the task manager and not actually launching the application to the users window? Code To Start The Process IPHostEntry hostEntry = Dns.GetHostEntry("InsertServerName"); WMIWrapper wrapper = new WMIWrapper("Insert User Name", "Insert Password", hostEntry.HostName); List<Process> processes = wrapper.GetProcesses(); foreach (Process process in processes) { if (process.Caption.Equals("MyAppName.exe")) { Console.WriteLine(process.Caption); Console.WriteLine(process.CommandLine); int processId; wrapper.StartProcess("E:\\MyData\\Data\\MyAppName.exe", out processId); Console.WriteLine(processId.ToString()); } } Console.ReadLine(); WMI Wrapper Code using System; using System.Collections.Generic; using System.Management; using System.Runtime.InteropServices; using Common.WMI.Objects; using System.Net; namespace Common.WMIWrapper { public class WMIWrapper : IDisposable { #region Constructor /// <summary> /// Creates a new instance of the wrapper /// </summary> /// <param jobName="username"></param> /// <param jobName="password"></param> /// <param jobName="server"></param> public WMIWrapper(string server) { Initialise(server); } /// <summary> /// Creates a new instance of the wrapper /// </summary> /// <param jobName="username"></param> /// <param jobName="password"></param> /// <param jobName="server"></param> public WMIWrapper(string username, string password, string server) { Initialise(username, password, server); } #endregion #region Destructor /// <summary> /// Clean up unmanaged references /// </summary> ~WMIWrapper() { Dispose(false); } #endregion #region Initialise /// <summary> /// Initialise the WMI Connection (local machine) /// </summary> /// <param name="server"></param> private void Initialise(string server) { m_server = server; // set connection options m_connectOptions = new ConnectionOptions(); IPHostEntry host = Dns.GetHostEntry(Environment.MachineName); } /// <summary> /// Initialise the WMI connection /// </summary> /// <param jobName="username">Username to connect to server with</param> /// <param jobName="password">Password to connect to server with</param> /// <param jobName="server">Server to connect to</param> private void Initialise(string username, string password, string server) { m_server = server; // set connection options m_connectOptions = new ConnectionOptions(); IPHostEntry host = Dns.GetHostEntry(Environment.MachineName); if (host.HostName.Equals(server, StringComparison.OrdinalIgnoreCase)) return; m_connectOptions.Username = username; m_connectOptions.Password = password; m_connectOptions.Impersonation = ImpersonationLevel.Impersonate; m_connectOptions.EnablePrivileges = true; } #endregion /// <summary> /// Return a list of available wmi namespaces /// </summary> /// <returns></returns> public List<String> GetWMINamespaces() { ManagementScope wmiScope = new ManagementScope(String.Format("\\\\{0}\\root", this.Server), this.ConnectionOptions); List<String> wmiNamespaceList = new List<String>(); ManagementClass wmiNamespaces = new ManagementClass(wmiScope, new ManagementPath("__namespace"), null); ; foreach (ManagementObject ns in wmiNamespaces.GetInstances()) wmiNamespaceList.Add(ns["Name"].ToString()); return wmiNamespaceList; } /// <summary> /// Return a list of available classes in a namespace /// </summary> /// <param jobName="wmiNameSpace">Namespace to get wmi classes for</param> /// <returns>List of classes in the requested namespace</returns> public List<String> GetWMIClassList(string wmiNameSpace) { ManagementScope wmiScope = new ManagementScope(String.Format("\\\\{0}\\root\\{1}", this.Server, wmiNameSpace), this.ConnectionOptions); List<String> wmiClasses = new List<String>(); ManagementObjectSearcher wmiSearcher = new ManagementObjectSearcher(wmiScope, new WqlObjectQuery("SELECT * FROM meta_Class"), null); foreach (ManagementClass wmiClass in wmiSearcher.Get()) wmiClasses.Add(wmiClass["__CLASS"].ToString()); return wmiClasses; } /// <summary> /// Get a list of wmi properties for the specified class /// </summary> /// <param jobName="wmiNameSpace">WMI Namespace</param> /// <param jobName="wmiClass">WMI Class</param> /// <returns>List of properties for the class</returns> public List<String> GetWMIClassPropertyList(string wmiNameSpace, string wmiClass) { List<String> wmiClassProperties = new List<string>(); ManagementClass managementClass = GetWMIClass(wmiNameSpace, wmiClass); foreach (PropertyData property in managementClass.Properties) wmiClassProperties.Add(property.Name); return wmiClassProperties; } /// <summary> /// Returns a list of methods for the class /// </summary> /// <param jobName="wmiNameSpace"></param> /// <param jobName="wmiClass"></param> /// <returns></returns> public List<String> GetWMIClassMethodList(string wmiNameSpace, string wmiClass) { List<String> wmiClassMethods = new List<string>(); ManagementClass managementClass = GetWMIClass(wmiNameSpace, wmiClass); foreach (MethodData method in managementClass.Methods) wmiClassMethods.Add(method.Name); return wmiClassMethods; } /// <summary> /// Retrieve the specified management class /// </summary> /// <param jobName="wmiNameSpace">Namespace of the class</param> /// <param jobName="wmiClass">Type of the class</param> /// <returns></returns> public ManagementClass GetWMIClass(string wmiNameSpace, string wmiClass) { ManagementScope wmiScope = new ManagementScope(String.Format("\\\\{0}\\root\\{1}", this.Server, wmiNameSpace), this.ConnectionOptions); ManagementClass managementClass = null; ManagementObjectSearcher wmiSearcher = new ManagementObjectSearcher(wmiScope, new WqlObjectQuery(String.Format("SELECT * FROM meta_Class WHERE __CLASS = '{0}'", wmiClass)), null); foreach (ManagementClass wmiObject in wmiSearcher.Get()) managementClass = wmiObject; return managementClass; } /// <summary> /// Get an instance of the specficied class /// </summary> /// <param jobName="wmiNameSpace">Namespace of the classes</param> /// <param jobName="wmiClass">Type of the classes</param> /// <returns>Array of management classes</returns> public ManagementObject[] GetWMIClassObjects(string wmiNameSpace, string wmiClass) { ManagementScope wmiScope = new ManagementScope(String.Format("\\\\{0}\\root\\{1}", this.Server, wmiNameSpace), this.ConnectionOptions); List<ManagementObject> wmiClasses = new List<ManagementObject>(); ManagementObjectSearcher wmiSearcher = new ManagementObjectSearcher(wmiScope, new WqlObjectQuery(String.Format("SELECT * FROM {0}", wmiClass)), null); foreach (ManagementObject wmiObject in wmiSearcher.Get()) wmiClasses.Add(wmiObject); return wmiClasses.ToArray(); } /// <summary> /// Get a full list of services /// </summary> /// <returns></returns> public List<Service> GetServices() { return GetService(null); } /// <summary> /// Get a list of services /// </summary> /// <returns></returns> public List<Service> GetService(string name) { ManagementObject[] services = GetWMIClassObjects("CIMV2", "WIN32_Service"); List<Service> serviceList = new List<Service>(); for (int i = 0; i < services.Length; i++) { ManagementObject managementObject = services[i]; Service service = new Service(managementObject); service.Status = (string)managementObject["Status"]; service.Name = (string)managementObject["Name"]; service.DisplayName = (string)managementObject["DisplayName"]; service.PathName = (string)managementObject["PathName"]; service.ProcessId = (uint)managementObject["ProcessId"]; service.Started = (bool)managementObject["Started"]; service.StartMode = (string)managementObject["StartMode"]; service.ServiceType = (string)managementObject["ServiceType"]; service.InstallDate = (string)managementObject["InstallDate"]; service.Description = (string)managementObject["Description"]; service.Caption = (string)managementObject["Caption"]; if (String.IsNullOrEmpty(name) || name.Equals(service.Name, StringComparison.OrdinalIgnoreCase)) serviceList.Add(service); } return serviceList; } /// <summary> /// Get a list of processes /// </summary> /// <returns></returns> public List<Process> GetProcesses() { return GetProcess(null); } /// <summary> /// Get a list of processes /// </summary> /// <returns></returns> public List<Process> GetProcess(uint? processId) { ManagementObject[] processes = GetWMIClassObjects("CIMV2", "WIN32_Process"); List<Process> processList = new List<Process>(); for (int i = 0; i < processes.Length; i++) { ManagementObject managementObject = processes[i]; Process process = new Process(managementObject); process.Priority = (uint)managementObject["Priority"]; process.ProcessId = (uint)managementObject["ProcessId"]; process.Status = (string)managementObject["Status"]; DateTime createDate; if (ConvertFromWmiDate((string)managementObject["CreationDate"], out createDate)) process.CreationDate = createDate.ToString("dd-MMM-yyyy HH:mm:ss"); process.Caption = (string)managementObject["Caption"]; process.CommandLine = (string)managementObject["CommandLine"]; process.Description = (string)managementObject["Description"]; process.ExecutablePath = (string)managementObject["ExecutablePath"]; process.ExecutionState = (string)managementObject["ExecutionState"]; process.MaximumWorkingSetSize = (UInt32?)managementObject ["MaximumWorkingSetSize"]; process.MinimumWorkingSetSize = (UInt32?)managementObject["MinimumWorkingSetSize"]; process.KernelModeTime = (UInt64)managementObject["KernelModeTime"]; process.ThreadCount = (UInt32)managementObject["ThreadCount"]; process.UserModeTime = (UInt64)managementObject["UserModeTime"]; process.VirtualSize = (UInt64)managementObject["VirtualSize"]; process.WorkingSetSize = (UInt64)managementObject["WorkingSetSize"]; if (processId == null || process.ProcessId == processId.Value) processList.Add(process); } return processList; } /// <summary> /// Start the specified process /// </summary> /// <param jobName="commandLine"></param> /// <returns></returns> public bool StartProcess(string command, out int processId) { processId = int.MaxValue; ManagementClass processClass = GetWMIClass("CIMV2", "WIN32_Process"); object[] objectsIn = new object[4]; objectsIn[0] = command; processClass.InvokeMethod("Create", objectsIn); if (objectsIn[3] == null) return false; processId = int.Parse(objectsIn[3].ToString()); return true; } /// <summary> /// Schedule a process on the remote machine /// </summary> /// <param name="command"></param> /// <param name="scheduleTime"></param> /// <param name="jobName"></param> /// <returns></returns> public bool ScheduleProcess(string command, DateTime scheduleTime, out string jobName) { jobName = String.Empty; ManagementClass scheduleClass = GetWMIClass("CIMV2", "Win32_ScheduledJob"); object[] objectsIn = new object[7]; objectsIn[0] = command; objectsIn[1] = String.Format("********{0:00}{1:00}{2:00}.000000+060", scheduleTime.Hour, scheduleTime.Minute, scheduleTime.Second); objectsIn[5] = true; scheduleClass.InvokeMethod("Create", objectsIn); if (objectsIn[6] == null) return false; UInt32 scheduleid = (uint)objectsIn[6]; jobName = scheduleid.ToString(); return true; } /// <summary> /// Returns the current time on the remote server /// </summary> /// <returns></returns> public DateTime Now() { ManagementScope wmiScope = new ManagementScope(String.Format("\\\\{0}\\root\\{1}", this.Server, "CIMV2"), this.ConnectionOptions); ManagementClass managementClass = null; ManagementObjectSearcher wmiSearcher = new ManagementObjectSearcher(wmiScope, new WqlObjectQuery(String.Format("SELECT * FROM Win32_LocalTime")), null); DateTime localTime = DateTime.MinValue; foreach (ManagementObject time in wmiSearcher.Get()) { UInt32 day = (UInt32)time["Day"]; UInt32 month = (UInt32)time["Month"]; UInt32 year = (UInt32)time["Year"]; UInt32 hour = (UInt32)time["Hour"]; UInt32 minute = (UInt32)time["Minute"]; UInt32 second = (UInt32)time["Second"]; localTime = new DateTime((int)year, (int)month, (int)day, (int)hour, (int)minute, (int)second); }; return localTime; } /// <summary> /// Converts a wmi date into a proper date /// </summary> /// <param jobName="wmiDate">Wmi formatted date</param> /// <returns>Date time object</returns> private static bool ConvertFromWmiDate(string wmiDate, out DateTime properDate) { properDate = DateTime.MinValue; string properDateString; // check if string is populated if (String.IsNullOrEmpty(wmiDate)) return false; wmiDate = wmiDate.Trim().ToLower().Replace("*", "0"); string[] months = new string[] { "Jan", "Feb", "Mar", "Apr", "May", "Jun", "Jul", "Aug", "Sep", "Oct", "Nov", "Dec" }; try { properDateString = String.Format("{0}-{1}-{2} {3}:{4}:{5}.{6}", wmiDate.Substring(6, 2), months[int.Parse(wmiDate.Substring(4, 2)) - 1], wmiDate.Substring(0, 4), wmiDate.Substring(8, 2), wmiDate.Substring(10, 2), wmiDate.Substring(12, 2), wmiDate.Substring(15, 6)); } catch (InvalidCastException) { return false; } catch (ArgumentOutOfRangeException) { return false; } // try and parse the new date if (!DateTime.TryParse(properDateString, out properDate)) return false; // true if conversion successful return true; } private bool m_disposed; #region IDisposable Members /// <summary> /// Managed dispose /// </summary> public void Dispose() { Dispose(true); GC.SuppressFinalize(this); } /// <summary> /// Dispose of managed and unmanaged objects /// </summary> /// <param jobName="disposing"></param> public void Dispose(bool disposing) { if (disposing) { m_connectOptions = null; } } #endregion #region Properties private ConnectionOptions m_connectOptions; /// <summary> /// Gets or sets the management scope /// </summary> private ConnectionOptions ConnectionOptions { get { return m_connectOptions; } set { m_connectOptions = value; } } private String m_server; /// <summary> /// Gets or sets the server to connect to /// </summary> public String Server { get { return m_server; } set { m_server = value; } } #endregion } }

    Read the article

  • Spam Activity From my computer

    - by Bnymn
    I'm using Ubuntu 12.04 64bit. I'm using HTTP proxy over ssh as mentioned here. If I do not start TinyProxy, everything is OK. But, when I start TinyProxy, I'm getting the following. I think there is an application running on my machine and watching the proxy to start. But I could not decide which one it could be. ps ax PID TTY STAT TIME COMMAND 1 ? Ss 0:01 /sbin/init 2 ? S 0:00 [kthreadd] 3 ? S 0:00 [ksoftirqd/0] 6 ? S 0:00 [migration/0] 7 ? S 0:00 [watchdog/0] 21 ? S< 0:00 [cpuset] 22 ? S< 0:00 [khelper] 23 ? S 0:00 [kdevtmpfs] 24 ? S< 0:00 [netns] 26 ? S 0:00 [sync_supers] 27 ? S 0:00 [bdi-default] 28 ? S< 0:00 [kintegrityd] 29 ? S< 0:00 [kblockd] 30 ? S< 0:00 [ata_sff] 31 ? S 0:00 [khubd] 32 ? S< 0:00 [md] 34 ? S 0:00 [khungtaskd] 35 ? S 0:00 [kswapd0] 36 ? SN 0:00 [ksmd] 37 ? SN 0:00 [khugepaged] 38 ? S 0:00 [fsnotify_mark] 39 ? S 0:00 [ecryptfs-kthrea] 40 ? S< 0:00 [crypto] 48 ? S< 0:00 [kthrotld] 49 ? S 0:00 [scsi_eh_0] 50 ? S 0:00 [scsi_eh_1] 51 ? S 0:00 [scsi_eh_2] 52 ? S 0:00 [scsi_eh_3] 75 ? S< 0:00 [devfreq_wq] 240 ? S< 0:00 [xfs_mru_cache] 241 ? S< 0:00 [xfslogd] 242 ? S< 0:00 [xfsdatad] 243 ? S< 0:00 [xfsconvertd] 245 ? S 0:00 [xfsbufd/sda3] 246 ? S 0:01 [xfsaild/sda3] 330 ? S 0:00 upstart-udev-bridge --daemon 333 ? Ss 0:00 /sbin/udevd --daemon 472 ? S< 0:00 [cfg80211] 479 ? S< 0:00 [kpsmoused] 671 ? S 0:00 upstart-socket-bridge --daemon 779 ? S 0:00 [xfsbufd/sda4] 781 ? S 0:01 [xfsaild/sda4] 785 ? S< 0:00 [ttm_swap] 800 ? S< 0:00 [hd-audio0] 803 ? S< 0:00 [hd-audio1] 857 ? Sl 0:00 rsyslogd -c5 869 ? Ss 0:04 dbus-daemon --system --fork --activation=upstart 881 ? Ss 0:00 /usr/sbin/modem-manager 883 ? Ss 0:00 /usr/sbin/bluetoothd 905 ? Ssl 0:02 NetworkManager 906 ? Ss 0:00 /usr/sbin/cupsd -F 910 ? Sl 0:02 /usr/lib/policykit-1/polkitd --no-debug 918 ? S 0:00 avahi-daemon: running [bunyamin-hp.local] 919 ? S 0:00 avahi-daemon: chroot helper 920 ? S< 0:00 [krfcommd] 956 ? Ss 0:00 /sbin/wpa_supplicant -B -P /run/sendsigs.omit.d/wpasupplicant.pid -u -s -O /var/run/wpa_supplicant 980 tty4 Ss+ 0:00 /sbin/getty -8 38400 tty4 985 tty5 Ss+ 0:00 /sbin/getty -8 38400 tty5 1000 tty2 Ss+ 0:00 /sbin/getty -8 38400 tty2 1006 tty3 Ss+ 0:00 /sbin/getty -8 38400 tty3 1009 tty6 Ss+ 0:00 /sbin/getty -8 38400 tty6 1024 ? Ss 0:00 acpid -c /etc/acpi/events -s /var/run/acpid.socket 1025 ? Ss 0:00 atd 1026 ? Ss 0:00 cron 1029 ? Ss 0:01 /usr/sbin/irqbalance 1034 ? Ssl 0:00 whoopsie 1091 ? Ssl 0:00 lightdm 1216 tty1 Ss+ 0:00 /sbin/getty -8 38400 tty1 1224 ? Sl 0:00 /usr/lib/accountsservice/accounts-daemon 1241 ? Sl 0:00 /usr/sbin/console-kit-daemon --no-daemon 1356 ? Sl 0:00 /usr/lib/upower/upowerd 1447 ? Sl 0:00 /usr/lib/x86_64-linux-gnu/colord/colord 1539 ? SNl 0:00 /usr/lib/rtkit/rtkit-daemon 1723 ? Sl 0:00 /usr/lib/udisks/udisks-daemon 1724 ? S 0:00 udisks-daemon: not polling any devices 2077 ? Z 0:00 [lightdm] <defunct> 2433 ? Z 0:00 [lightdm] <defunct> 3491 ? S 0:00 [flush-8:0] 4023 ? S 0:00 [kworker/u:14] 4034 ? S 0:00 [migration/1] 4035 ? S 0:00 [kworker/1:3] 4036 ? S 0:00 [ksoftirqd/1] 4037 ? S 0:00 [watchdog/1] 4038 ? S 0:00 [migration/2] 4040 ? S 0:00 [ksoftirqd/2] 4041 ? S 0:00 [watchdog/2] 4042 ? S 0:00 [migration/3] 4043 ? S 0:00 [kworker/3:1] 4044 ? S 0:00 [ksoftirqd/3] 4045 ? S 0:00 [watchdog/3] 4047 ? S 0:00 [irq/43-mei] 4070 ? S 0:00 [kworker/3:0] 4072 ? S 0:00 [kworker/1:0] 4164 ? Ss 0:00 anacron -s 4549 tty7 Ss+ 1:13 /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch 4683 ? Sl 0:00 lightdm --session-child 12 47 4718 ? Sl 0:00 /usr/bin/gnome-keyring-daemon --daemonize --login 4729 ? Ssl 0:00 gnome-session --session=gnome-fallback 4765 ? Ss 0:00 /usr/bin/ssh-agent /usr/bin/dbus-launch --exit-with-session gnome-session --session=gnome-fallback 4768 ? S 0:00 /usr/bin/dbus-launch --exit-with-session gnome-session --session=gnome-fallback 4769 ? Ss 0:00 //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session 4779 ? Sl 0:01 /usr/lib/gnome-settings-daemon/gnome-settings-daemon 4786 ? S 0:00 /usr/lib/gvfs/gvfsd 4788 ? Sl 0:00 /usr/lib/gvfs//gvfs-fuse-daemon -f /home/bunyamin/.gvfs 4797 ? Sl 0:00 /usr/lib/gnome-settings-daemon/gsd-printer 4799 ? Sl 0:03 metacity 4805 ? S 0:00 /usr/lib/x86_64-linux-gnu/gconf/gconfd-2 4811 ? Sl 0:10 gnome-panel 4814 ? S 0:00 syndaemon -i 2.0 -K -R -t 4819 ? S<l 0:00 /usr/bin/pulseaudio --start --log-target=syslog 4821 ? Sl 0:00 /usr/lib/dconf/dconf-service 4826 ? Sl 0:00 /usr/lib/gnome-settings-daemon/gnome-fallback-mount-helper 4828 ? Sl 0:06 nautilus -n 4830 ? Sl 0:02 nm-applet 4832 ? Sl 0:00 /usr/lib/policykit-1-gnome/polkit-gnome-authentication-agent-1 4835 ? Sl 0:00 bluetooth-applet 4851 ? S 0:00 /usr/lib/pulseaudio/pulse/gconf-helper 4854 ? Sl 0:04 /usr/lib/indicator-applet/indicator-applet-complete 4859 ? S 0:00 /usr/lib/gvfs/gvfs-gdu-volume-monitor 4863 ? S 0:00 /usr/lib/gvfs/gvfs-gphoto2-volume-monitor 4865 ? Sl 0:00 /usr/lib/gvfs/gvfs-afc-volume-monitor 4871 ? S 0:00 /usr/lib/gvfs/gvfsd-trash --spawner :1.6 /org/gtk/gvfs/exec_spaw/0 4874 ? Sl 0:00 /usr/lib/indicator-application/indicator-application-service 4876 ? Sl 0:00 /usr/lib/indicator-datetime/indicator-datetime-service 4878 ? Sl 0:00 /usr/lib/indicator-messages/indicator-messages-service 4887 ? Sl 0:00 /usr/lib/indicator-printers/indicator-printers-service 4888 ? Sl 0:00 /usr/lib/indicator-session/indicator-session-service 4889 ? Sl 0:00 /usr/lib/indicator-sound/indicator-sound-service 4906 ? S 0:00 /usr/lib/geoclue/geoclue-master 4929 ? S 0:00 /usr/lib/ubuntu-geoip/ubuntu-geoip-provider 4938 ? Sl 0:11 /usr/lib/gnome-applets/multiload-applet-2 4939 ? Sl 0:01 /usr/lib/gnome-applets/cpufreq-applet 4953 ? S 0:00 /usr/lib/gvfs/gvfsd-metadata 4955 ? S 0:00 /usr/lib/gvfs/gvfsd-burn --spawner :1.6 /org/gtk/gvfs/exec_spaw/1 4957 ? Sl 3:22 /usr/lib/firefox/firefox 4973 ? Sl 0:00 /usr/lib/x86_64-linux-gnu/at-spi2-core/at-spi-bus-launcher 4997 ? Sl 0:00 /usr/lib/gnome-disk-utility/gdu-notification-daemon 5000 ? Sl 0:00 telepathy-indicator 5007 ? Sl 0:00 /usr/lib/telepathy/mission-control-5 5012 ? Sl 0:00 /usr/lib/gnome-online-accounts/goa-daemon 5018 ? Sl 0:00 gnome-screensaver 5019 ? Sl 0:01 zeitgeist-datahub 5025 ? Sl 0:00 /usr/bin/zeitgeist-daemon 5033 ? Sl 0:00 /usr/lib/zeitgeist/zeitgeist-fts 5041 ? S 0:00 /bin/cat 5052 ? Sl 0:08 /usr/bin/gnome-terminal -x /bin/sh -c '/home/bunyamin/Desktop/SSH Tunnel' 5058 ? S 0:00 gnome-pty-helper 5067 ? Sl 0:00 update-notifier 5090 ? S 0:00 /usr/bin/python /usr/lib/system-service/system-service-d 5130 ? Sl 0:00 /usr/lib/deja-dup/deja-dup/deja-dup-monitor 5135 ? S 0:00 /bin/sh -c nice run-parts --report /etc/cron.daily 5136 ? SN 0:00 run-parts --report /etc/cron.daily 5358 pts/4 Ss 0:00 bash 5482 ? S 0:00 [kworker/0:1] 5487 ? S 0:01 [kworker/2:0] 5550 ? Sl 1:15 /usr/lib/firefox/plugin-container /usr/lib/flashplugin-installer/libflashplayer.so -greomni /usr/lib/firefox/omni.ja 4957 true plugin 5717 ? S 0:00 /usr/lib/cups/notifier/dbus dbus:// 5824 ? SN 0:00 /bin/sh /etc/cron.daily/update-notifier-common 5825 ? SN 0:00 /usr/bin/python /usr/lib/update-notifier/package-data-downloader 5872 ? Sl 0:00 /usr/lib/notify-osd/notify-osd 5888 ? S 0:00 /sbin/udevd --daemon 5889 ? S 0:00 /sbin/udevd --daemon 5909 ? S 0:00 /sbin/dhclient -d -4 -sf /usr/lib/NetworkManager/nm-dhcp-client.action -pf /var/run/sendsigs.omit.d/network-manager.dhclient-eth1.pid -lf /var/lib/dhcp/dhclient-f5f0 5912 ? S 0:00 /usr/sbin/dnsmasq --no-resolv --keep-in-foreground --no-hosts --bind-interfaces --pid-file=/var/run/sendsigs.omit.d/network-manager.dnsmasq.pid --listen-address=127. 5975 pts/1 Ss+ 0:00 /bin/sh -c '/home/bunyamin/Desktop/SSH Tunnel' 5976 pts/1 S+ 0:00 /bin/sh /home/bunyamin/Desktop/SSH Tunnel 5977 pts/1 S+ 0:00 ssh -p443 [email protected] -L 8000:127.0.0.1:8000 5980 ? Sl 0:00 /usr/lib/gvfs/gvfsd-http --spawner :1.6 /org/gtk/gvfs/exec_spaw/2 6034 ? S 0:00 [kworker/u:0] 6054 ? S 0:00 [kworker/2:2] 6070 ? S 0:00 [kworker/0:3] 6094 ? Sl 0:02 gedit /home/bunyamin/Desktop/a.html 6101 ? S 0:00 [kworker/0:2] 6130 pts/4 R+ 0:00 ps ax TinyProxy LOG connect to ad.adserverplus.com:80 mx1.u4gf.com - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/imp?Z=160x600&s=2959021&T=3&_salt=1516586745&B=12&m=2&u=http%3A%2F%2Fsunshinefelling.com%2Findex.php%3Fview%3Darticle%26catid%3D45%253Aplus-size-dresses%26id%3D7512%253A2012-01-25-22-42-00%26format%3Dpdf%26option%3Dcom_content%26Itemid%3D101&r=1 HTTP/1.0" - - bye bye bye connect to ad.adserverplus.com:80 connect to ad.bharatstudent.com:80 connect to ad.yieldmanager.com:80 142.91.199.250.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=0x0&y=29&s=2913320&_salt=2228719469&B=12&m=2&r=1 HTTP/1.0" - - 173.208.94.117 - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=0x0&y=29&s=3187816&_salt=462045326&B=12&m=2&r=1 HTTP/1.0" - - mx1.a54m.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=300x250&s=2887338&T=3&_salt=2925281520&B=12&m=2&u=http%3A%2F%2Fsecretskirt.com%2Findex.php%3Foption%3Dcom_contact%26view%3Dcontact%26id%3D1%26Itemid%3D95&r=1 HTTP/1.0" - - 108.62.75.54.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=300x250&s=3218437&T=3&_salt=2939054384&B=12&m=2&u=http%3A%2F%2Fwww.vifinances.com%2Ffinance-investing%2Finsurance-investment%2Fis-life-insurance-investment-necessarily-the-way-to-go.html&r=1 HTTP/1.0" - - connect to ad.yieldmanager.com:80 connect to ad.globe7.com:80 bye connect to ad.globe7.com:80 connect to ad.globe7.com:80 bye 173.208.94.22 - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=728x90&s=2922824&T=3&_salt=705371051&B=12&m=2&u=%3A%2F%2Fsunshinefelling.com%2Findex.php%3Fview%3Darticle%26catid%3D44%3Amature-womens-fashion%26id%3D6917%3A2012-01-25-22-37-27%26tmpl%3Dcomponent%26print%3D1%26layout%3Ddefault%26page%3D&r=1 HTTP/1.0" - - bye 23.19.10.44.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/st?ad_type=iframe&ad_size=160x600&section=3512129&pub_url=${PUB_URL} HTTP/1.0" - - connect to ad.yieldmanager.com:80 bye 142.91.189.27.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/imp?Z=0x0&y=29&s=3660215&_salt=2921537966&B=12&m=2&r=1 HTTP/1.0" - - connect to ad.scanmedios.com:80 bye 142.91.217.158.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globaltakeoff.net/st?ad_type=iframe&ad_size=160x600&section=2077929&pub_url=${PUB_URL} HTTP/1.0" - - 23.19.76.194.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=728x90&s=3127996&T=3&_salt=1952612979&B=12&m=2&u=http%3A%2F%2Fwww.oseey.com%2Fpure-core-watch%2Fcarbon-fiber-watch%2Fcarbon-monoxide-poisoning-awareness.html&r=1 HTTP/1.0" - - mx1.e6sb.com - - [17/Oct/2012 07:38:53] "GET http://ad.scanmedios.com/imp?Z=728x90&s=3522638&T=3&_salt=3444993091&B=12&m=2&u=http%3A%2F%2Fsunshinefelling.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D6013%3A2012-01-25-22-25-54%26catid%3D40%3Abig-beautiful-women-fashion%26Itemid%3D96&r=1 HTTP/1.0" - - connect to ad.tagjunction.com:80 connect to ad.yieldmanager.com:80 bye connect to ad.yieldmanager.com:80 23.19.76.154.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=300x250&section=2569393 HTTP/1.0" - - connect to ads.creafi-online-media.com:80 bye 108.62.109.115.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=0x0&y=29&s=3315330&_salt=2385926515&B=12&m=2&r=1 HTTP/1.0" - - 142.91.217.214.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=3634166&T=3&_salt=1590442300&B=12&m=2&u=http%3A%2F%2Fwealthterritory.com%2Findex.php%3Foption%3Dcom_mailto%26tmpl%3Dcomponent%26link%3DaHR0cDovL3dlYWx0aHRlcnJpdG9yeS5jb20vaW5kZXgucGhwP29wdGlvbj1jb21fY29udGVudCZ2aWV3PWFydGljbGUmaWQ9NDY2NDoyMDExLTA3LTA2LTEzLTI2LTUwJmNhdGlkPTQxOnNlcnZpY2VzJkl0ZW1pZ&r=1 HTTP/1.0" - - 108.62.185.184.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ads.creafi-online-media.com/imp?Z=728x90&s=2885766&T=3&_salt=107120374&B=12&m=2&u=http%3A%2F%2Feconomicccore.com%2Findex.php%3Foption%3Dcom_content%26view%3Dcategory%26layout%3Dblog%26id%3D48%26Itemid%3D98%26limitstart%3D45&r=1 HTTP/1.0" - - bye bye bye connect to ad.adserverplus.com:80 connect to ad.yieldmanager.com:80 connect to ad.tagjunction.com:80 bye 108.62.75.252.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=728x90&section=3213387&pub_url=${PUB_URL} HTTP/1.0" - - bye connect to ad.tagjunction.com:80 bye connect to ad.yieldmanager.com:80 173.208.94.29 - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/st?ad_type=iframe&ad_size=728x90&section=3006024&pub_url=${PUB_URL} HTTP/1.0" - - 23.19.31.84.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=0x0&y=29&s=2586703&_salt=2905995697&B=12&m=2&r=1 HTTP/1.0" - - oxx-ef-Words.ipwagon.net - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/imp?Z=0x0&y=29&s=3630499&_salt=4037530564&B=12&m=2&r=1 HTTP/1.0" - - 142.91.185.53.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/imp?Z=0x0&y=29&s=3512541&_salt=1134875077&B=12&m=2&r=1 HTTP/1.0" - - connect to ad.globe7.com:80 108.177.187.37.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=300x250&s=3168350&T=3&_salt=548860046&B=12&m=2&u=http%3A%2F%2Flifehealthyliving.com%2Findex.php%3Fview%3Darticle%26catid%3D34%253Ahealthy-food%26id%3D4681%253A2012-05-16-20-40-19%26tmpl%3Dcomponent%26print%3D1%26layout%3Ddefault%26page%3D%26option%3Dcom_content%26Itemid%3D53&r=1 HTTP/1.0" - - connect to ad.adserverplus.com:80 bye connect to ads.creafi-online-media.com:80 108.177.223.180.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=300x250&s=3331290&T=3&_salt=1270334669&B=12&m=2&u=http%3A%2F%2Fwww.vegls.com%2Faccident-attorneys-firms%2Fauto-accident-attorney%2Ffind-the-correct-auto-accident-attorney.html&r=1 HTTP/1.0" - - bye 142.91.185.38.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/st?ad_type=iframe&ad_size=160x600&section=818253 HTTP/1.0" - - connect to ad.yieldmanager.com:80 bye bye bye 108.62.75.230.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ads.creafi-online-media.com/st?ad_type=pop&ad_size=0x0&section=3323456&banned_pop_types=29&pop_times=1&pop_frequency=86400&pub_url=${PUB_URL} HTTP/1.0" - - connect to ad.adserverplus.com:80 bye connect to ad.adserverplus.com:80 bye 142.91.217.194.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=300x250&s=3068801&T=3&_salt=1246107431&B=12&m=2&u=http%3A%2F%2Fmoodoffashionandbeauty.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D756%3A2011-07-13-13-13-43%26catid%3D36%3Afashion-clothes%26Itemid%3D55&r=1 HTTP/1.0" - - connect to ad.smxchange.com:80 108.62.185.235.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=300x250&section=3307618&pub_url=${PUB_URL} HTTP/1.0" - - connect to ad.globe7.com:80 bye connect to ad.yieldmanager.com:80 bye bye connect to ad.adserverplus.com:80 connect to ad.yieldmanager.com:80 connect to ad.adserverplus.com:80 connect to ad.yieldmanager.com:80 108.177.168.183.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/imp?Z=300x250&s=3582877&T=3&_salt=3271923155&B=12&m=2&u=http%3A%2F%2Fwomenhealthroad.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D5780%3A2011-12-12-16-56-53%26catid%3D40%3Ahealth-issues%26Itemid%3D96&r=1 HTTP/1.0" - - 23.19.3.100.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=2895969&T=3&_salt=207805714&B=12&m=2&u=http%3A%2F%2Feconomicccore.com%2Findex.php%3Fview%3Darticle%26catid%3D46%253Aeconomic-news%26id%3D6079%253A2011-09-29-07-39-13%26format%3Dpdf%26option%3Dcom_content%26Itemid%3D96&r=1 HTTP/1.0" - - bye 142.91.199.212.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=300x250&section=2956039&pub_url=${PUB_URL} HTTP/1.0" - - bye 142.91.189.169.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=728x90&s=3004691&T=3&_salt=2747591679&B=12&m=2&u=http%3A%2F%2Fwww.qtsfinancial.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D5406%3Afinancial-statement-english-page%26catid%3D43%3Afinancial-analysis%26Itemid%3D99&r=1 HTTP/1.0" - - connect to ad.adserverplus.com:80 23.19.31.58.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=0x0&y=29&s=3323560&_salt=3172064457&B=12&m=2&r=1 HTTP/1.0" - - connect to ad.adserverplus.com:80 iei-ix-Words.ipwagon.net - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=728x90&s=3187813&T=3&_salt=1110944041&B=12&m=2&u=http%3A%2F%2Fwww.workinhouses.com%2Fhtml%2Fwallingford-ct-connecticuts-best-places-for-your-home.html&r=1 HTTP/1.0" - - connect to cookex.amp.yahoo.com:80 173.208.94.116 - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=300x250&section=3213592&pub_url=${PUB_URL} HTTP/1.0" - - bye bye connect to ad.yieldmanager.com:80 connect to ads.creafi-online-media.com:80 bye 108.62.75.99.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=160x600&s=2913321&T=3&_salt=333033369&B=12&m=2&u=http%3A%2F%2Ffashionstreetlight.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D28850%3A2011-12-20-12-59-39%26catid%3D45%3Afashion-accessories%26Itemid%3D101&r=1 HTTP/1.0" - - bye 142.91.217.208.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://cookex.amp.yahoo.com/v2/cexposer/SIG=18kthu27g/*http%3A//ad.yieldmanager.com/imp?Z=300x250&s=2682517&T=3&_salt=1378331643&B=12&m=2&u=http%3A%2F%2Fwww.economicwindows.com%2Findex.php%3Fview%3Darticle%26catid%3D40%253Afinancial-info%26id%3D3854%253A2011-07-06-13-25-37%26format%3Dpdf%26option%3Dcom_content%26Itemid%3D96&r=1 HTTP/1.0" - - bye bye bye 108.62.185.228.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=0x0&y=29&s=3315448&_salt=4241487555&B=12&m=2&r=1 HTTP/1.0" - - 108.62.185.220.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ads.creafi-online-media.com/st?ad_type=iframe&ad_size=728x90&section=3269968 HTTP/1.0" - - connect to ad.tagjunction.com:80 bye connect to ad.globe7.com:80 bye 142.91.185.47.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/st?ad_type=pop&ad_size=0x0&section=2958317&banned_pop_types=29&pop_times=1&pop_frequency=0&pub_url=${PUB_URL} HTTP/1.0" - - bye 108.177.168.183.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/imp?Z=160x600&s=3582877&T=3&_salt=1313872999&B=12&m=2&u=http%3A%2F%2Fwomenhealthroad.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D5753%3A2011-12-12-16-56-46%26catid%3D40%3Ahealth-issues%26Itemid%3D96&r=1 HTTP/1.0" - - connect to ad.tagjunction.com:80 bye connect to ad.globe7.com:80 bye connect to ad.adserverplus.com:80 108.62.75.53.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.tagjunction.com/imp?Z=300x250&s=3127172&T=3&_salt=2152278771&B=12&m=2&u=http%3A%2F%2Fwww.oslims.com%2Ffashion-coffee%2Ffashion-slimming-coffee%2Fso-whats-your-poison-coffee-or-tea.html&r=1 HTTP/1.0" - - connect to ad.yieldmanager.com:80 bye bye 108.62.75.170.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/imp?Z=0x0&y=29&s=2909210&_salt=1773835502&B=12&m=2&r=1 HTTP/1.0" - - 23.19.79.3.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.globe7.com/st?ad_type=iframe&ad_size=728x90&section=3571505&pub_url=${PUB_URL} HTTP/1.0" - - 142.91.217.216.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=3630472&T=3&_salt=462936220&B=12&m=2&u=http%3A%2F%2Fwww.economicwindows.com%2Findex.php%3Fview%3Darticle%26catid%3D41%253Afinancial-services%26id%3D4854%253A2011-07-06-13-26-56%26tmpl%3Dcomponent%26print%3D1%26layout%3Ddefault%26page%3D%26option%3Dcom_content%26Itemid%3D97&r=1 HTTP/1.0" - - connect to ad.yieldmanager.com:80 connect to ad.adserverplus.com:80 connect to ad.yieldmanager.com:80 bye connect to ad.yieldmanager.com:80 bye connect to ad.yieldmanager.com:80 142.91.189.176.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=3187822&T=3&_salt=325267799&B=12&m=2&u=http%3A%2F%2Feconomysea.com%2Findex.php%3Foption%3Dcom_mailto%26tmpl%3Dcomponent%26link%3DaHR0cDovL2Vjb25vbXlzZWEuY29tL2luZGV4LnBocD9vcHRpb249Y29tX2NvbnRlbnQmdmlldz1hcnRpY2xlJmlkPTYzNDk6MjAxMS0wOS0yOC0yMC0wNC0xOSZjYXRpZD00NzplY29ub21pYy1uZXdzJkl0ZW1pZD05Nw&r=1 HTTP/1.0" - - connect to ad.adserverplus.com:80 142.91.190.240.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=2956040&T=3&_salt=3354730349&B=12&m=2&u=http%3A%2F%2Fdomarketings.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D279%3AWhy-Contractor-Leads-Are-Best-For-Getting-Ideal-Construction-Prospects%26catid%3D2%3Abusiness&r=1 HTTP/1.0" - - bye 108.62.75.6.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=3323456&T=3&_salt=1244915826&B=12&m=2&u=http%3A%2F%2Fdomarketings.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D989%3AThe-Basics-of-Failure-Mode-and-Effective-Analysis%26catid%3D2%3Abusiness&r=1 HTTP/1.0" - - bye 142.91.217.220.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=728x90&s=2921135&T=3&_salt=1337464905&B=12&m=2&u=http%3A%2F%2Financezone.com%2Findex.php%3Foption%3Dcom_content%26view%3Darticle%26id%3D7236%3A2011-09-05-19-56-54%26catid%3D49%3Acareer-banking%26Itemid%3D99&r=1 HTTP/1.0" - - bye connect to ad.yieldmanager.com:80 108.62.178.229.rdns.ubiquityservers.com - - [17/Oct/2012 07:38:53] "GET http://ad.adserverplus.com/st?ad_type=iframe&ad_size=160x600&section=3168350&pub_url=${PUB_URL} HTTP/1.0" - - connect to ad.yieldmanager.com:80 108.177.168.187.rdns.ubiquity.io - - [17/Oct/2012 07:38:53] "GET http://ad.smxchange.com/st?ad_type=iframe&ad_size=300x250&section=3285387&pop_nofreqcap=1&pub_url=${PUB_URL} HTTP/1.0" - - skg-wr-Words.ipwagon.net - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=0x0&y=29&s=3153972&_salt=3512711469&B=12&m=2&r=1 HTTP/1.0" - - bye connect to ad.yieldmanager.com:80 bye connect to ad.yieldmanager.com:80 mx1.u4gf.com - - [17/Oct/2012 07:38:53] "GET http://ad.yieldmanager.com/imp?Z=160x600&s=2959021&T=3&_salt=1516586745&B=12&m=2&u=http%3A%2F%2Fsunshinefelling.com%2Findex.php%3Fview%3Darticle%26catid%3D45%253Aplus-size-dresses%26id%3D7512%253A2012-01-25-22-42-00%26format%3Dpdf%26option%3Dcom_content%26Itemid%3D101&r=1 HTTP/1.0" - -

    Read the article

< Previous Page | 5 6 7 8 9