Search Results

Search found 20827 results on 834 pages for 'check'.

Page 9/834 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• Run disk error check on NTFS file?

  - by paulius_l

  I have a feeling that my system hard drive is dying. Benchmark kind of enforces it. Here is the benchmark of my system hard drive during low system activity: And here is the benchmark of backup drive: Furthermore, there are some files which I just can't touch because I get CRC errors and the hard drive activity spikes to 100% with operating speeds less than 1 MB/s while working with such files. I haven't yet tried swapping SATA cable as I have read this might cause the problems. Anyway, I would like to run some tests on specific clustsers where those files I am interested in are stored. I don't want to do the full chkdsk because it takes a very long time. I would like to either find the utility which executes the disk check directly on the clusters where the file belongs or a couple utilities where one tells me the cluster locations and another can check just those locations. How do I check and possibly fix disk errors where the files I am interested in are stored? Edit: S.M.A.R.T. info:

  Read the article

• Meaning of Bridge-Check in iptables flowchart

  - by networkIT

  In the famous iptables flow-chart what does bridge-check exactly stands for ? I couldn't find any documentation. The only clue I found was while scanning the MikroTik RouterOS documentation ( RouterOS is build upon a Linux 2.6.16 kernel ), I found this : In-interface Bridge = Checks if the input interface is a port for a bridge or is the bridge. Manual:Packet Flow Comparing both flow-charts brings clues that iptables Bridge-check might equal MikroTik In-Interface Bridge. Is this true ? Else, what might be the meaning of iptables Bridge-Check ?

  Read the article

• WSUS Showing Incorrect Version & Client Update Failure but they can check-in

  - by user132199

  One of the issues we are having is the clients will not download the updates from our WSUS server. They check-in as they are suppose too and find applicable updates but they are unable to actually download and install them. The GPO is set correctly. We decided to install the patch KB2720211to see if it would help eleviate this issue but it did not. In fact, even stranger, if I check the version that is installed on WSUS it reads 3.2.7600.226 but as far as I know it should read 3.2.7600.251. If I check Add/Remove programs to see what Windows Updates have been installed it even lists for WSUS that KB2720211 has been installed at version 3.2.7600.251. To install this update I followed the following directions Question: Has anyone seen this issue where the patch is installed yet not showing the correct version? What can I try to get my clients to update?

  Read the article

• Does CHECK TABLE add read/write locks?

  - by Ztyx

  Hi, Yesterday I ran CHECK TABLE on a table that is read very frequently. I scanned the MySQL documentation for CHECK TABLE for any mentions of "lock" (and found none) and also noticed that only SELECT privilege was required to run the command. I therefor concluded that the command did not do any read lock and was safe to run even in production. Sadly, running the command took 1 minute and 37 seconds and seemed to block all read access. My question is therefor, does CHECK TABLE do any read lock? Any other reason why I experienced a read block on the table? Thanks

  Read the article

• How often does a Linux check it's /etc/localtime file

  - by DarkSheep

  I am trying to troubleshoot a problem. Some very helpful information would lead me to a solution is: Often does Linux check the /etc/localtime file? Additionally if there is a configuration file to increase the frequency (for testing) that would be helpful. Normally I would assume that it would check when a call to the ntp server has been executed, but NTP is not installed. It couldn't possibly check every time the date function is called as this would result in many problems on busy web servers. Server is Ubuntu 12.04, but I don't think that is relevant to the question.

  Read the article

• Spellchecking po files

  - by moose

  Hi, I am translating some po-files and I would like to run a spell checker over them. I have Ubuntu 10.10 and use gtranslator. As far as I know, gtranslator can't spellcheck the whole file. I tried ispell: $ ispell lordsawar-0.2.0-pre4.de.po - this doesn't work, as English and German strings, as well as some programming-relevant comments appear in the .po-file. Do you know any program running on Ubuntu which can spell check po-files?

  Read the article

• How do I disable automatic hyphen correction in OS X 10.7?

  - by user167706

  How do I disable automatic hyphen correction in OS X 10.7? When using the spell checker in Apple Mail it is always prompting to correct my hyphens to another one which is essentially similar but microns longer on the screen for some reason. It's annoying as I often use hyphens and really need spell check too. Thoughts? I looked in all the usual System Preferences places but can't find anything.

  Read the article

• Javascript: Dynamic Check box (Fieldset with Father/Child Checkboxes)

  - by BoDiE2003

  I have a problem here, when I select any of the 'father' checkboxes all the child checkboxes are getting enabled or disabled. So I need each father checkbox to affect it own child fieldset. Could someone help me with this. Thank you <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html lang="en"> <head> <title>toggle disabled</title> <meta http-equiv="Content-Type" content="text/html; charset=utf-8"> <style type="text/css"> .cssDisabled { color: #ccc; } </style> <script src="http://prototypejs.org/assets/2009/8/31/prototype.js" type="text/javascript"> </script> <script type="text/javascript"> Event.observe(window, 'load', function(){ // for all items in the group_first class $$('.father').each(function(chk1){ // watch for clicks chk1.observe('click', function(evt){ dynamicCheckbox(); }); dynamicCheckbox(); }); }); function dynamicCheckbox (){ // count how many of group_first are checked, // doEnable true if any are checked var doEnable = ($$('.father:checked').length > 0) ? true : false; // for each in group_second, enable the checkbox, and // remove the cssDisabled class from the parent label $$('.child').each(function(item){ if (doEnable) { item.enable().up('label').removeClassName('cssDisabled'); } else { item.disable().up('label').addClassName('cssDisabled'); } }); }; </script> </head> <body> <fieldset> <legend>First Group</legend> <label><input type="checkbox" value="1" class="father" />Check box 1</label><br /> <label><input type="checkbox" value="2" class="father" checked/>Check box 2</label> </fieldset> <fieldset> <legend>Second Group</legend> <label class="cssDisabled"><input type="checkbox" value="x" class="child" disabled="disabled" />Check box x</label><br /> <label class="cssDisabled"><input type="checkbox" value="y" class="child" disabled="disabled" />Check box y</label><br /> <label class="cssDisabled"><input type="checkbox" value="z" class="child" disabled="disabled" />Check box z</label> </fieldset> <fieldset> <legend>First Group</legend> <label><input type="checkbox" value="3" class="father" />Check box 1</label><br /> </fieldset> <fieldset> <legend>Second Group</legend> <label class="cssDisabled"><input type="checkbox" value="x" class="child" disabled="disabled" />Check box x</label><br /> <label class="cssDisabled"><input type="checkbox" value="y" class="child" disabled="disabled" />Check box y</label><br /> <label class="cssDisabled"><input type="checkbox" value="z" class="child" disabled="disabled" />Check box z</label> </fieldset> </body> </html>

  Read the article

• How do I check a reverse PTR record?

  - by Daisetsu

  I need to check a reverse PTR record to make sure that a script I have is sending emails which will actually received by my users and not incorrectly marked as spam. I understand that the ISP which owns the IP range has to set up the PTR record, but how do I check if it is already set up?

  Read the article

• Software to check configuration and diagnostic of my PC is well configured

  - by aiacet

  Is there a utility, software or program than can check that my PC is well configured? Features I'm looking for: Checks to see if the communications between all the components works correctly Indicates if the OS is working properly Check the RAM and memory paging is configured correctly My system: AMD Phenom II X4 955 Black Box 125W Asus M4A785TD-M EVO Radeon HD5770 1GB GDDR5 Asus CoolerMaster GX 650W G.Skill 2x2GB PC3-12800 1600Mhz-787 4GBECO Western Digital 1TB SATAII 64MB Windows XP 32bit Antivirus and firewall: F-secure

  Read the article

• How to check mysql remote connectivity

  - by Mirage

  I have enable the ips in WHM for remote mysql but still i am not able to connect it. Is there any shell command for mysql which i can type to check the remote connectivity I mean any command to execute on server itself where mysql is installed or Any command to execute of local linux to check connectivity on remote MYsql server OS remote :Centos 5.4 local OS : Ubuntu

  Read the article

• How Amazon ELB Health check Works?

  - by diegodias

  I am having problems configuring ELB for my servers. I start 2 micro instances with the exact same conf and try to do Load Balancing. However they never pass the health check (HTTP port 80 path:"/"). Ping is ok on the website. So is telnet on 80. How did the health check works? Am I doing anything really wrong? EDIT: Both Direct browser access and GET (via curl) works correctly (status 200)

  Read the article

• Windows integrity check

  - by crazybmanp

  is there any way to check and make sure that my windows installation is completely fine (i just had a BSOD and i just want peace of mind it wont happen again). i am running windows 7, but i often give help to others so if there is any utility that works like this on another OS, post it. (also does disk check do this, i have had troubles with the windows seven disk checker as part of the error described in KB975778)

  Read the article

• How to check if the license on the server is a TechNet License

  - by user28471

  I have a server machine with Windows 2008 Web Server running on it and I THINK I have been running it under the TechNet license. Now I need to turn it into a production server and I need to find out if I really am running it under a TechNet license so that I can upgrade it. But I can't seem to be able to check which license I am running the OS under. Is there a way to check this?

  Read the article

• Check a specific value in application?

  - by Iyad

  Hi; I have a network with almost 2000 pc, on each of them i have an application installed for monitoring and mgmt, i need to check a specific value in each agent on the 2000 pc, which cant be checked unless you enter each pc and check the properties of the application ! is there any way to automate a process, script to do this.

  Read the article

• ubuntu , how to check how many cd drives are attached to computer

  - by Mirage

  How can i check which cd drives are attched to computer and is ubuntu detecting them or not i have seen that there were few drives which werenot showing on the computer but when i mouted them then it shows but i used gparted to see their /dev/sda1 address. but how can i check the cd drives so that i can mount them

  Read the article

• check_mk IPMI PCM sensor reading randomly fails

  - by Julian Kessel

  I use check_mk_agent for monitoring a server with IPMI and the freeipmi-tools installed. As far as I can see, the monitoring randomly detects no value returned by the IPMI Sensor "Temperature_PCH_Temp". That's a problem since it results in a CRITICAL state triggering a notification. The interruption lasts only over one check, the following is always OK. The temperature is in no edge area and neither the readings before the fail nor after show a Temp that is tending to overrun a treshold. Has someone an idea on what could be the reason for this behaviour and how prevent it?

  Read the article

• scheduled chkdsk on Windows 7 blinking the hard disk light every 5 seconds, what can I do?

  - by Jian Lin

  PG&E (the local electricity company) came and took out the old power meters and put in a new ones by brute force and with no advance notice in our neighborhood, so my computer went down in power. So I went to Windows 7's drive C and schedule a Disk Cleanup (chkdsk) on the next boot up. When it boots up, it says A disk check has been scheduled To skip disk checking, press any key within __ second(s). and then after it shows To skip disk checking, press any key within 1 second(s). it just sits there, with no further message. the hard disc light blinks every 5 seconds. So what is to be done now? I certainly don't want to brute force power off again.

  Read the article

• Control third check box based on the state of the first two using jquery

  - by Moj

  I have three check boxes and need to disable the third if either and/or of the other two are checked. I'm sure there's a easier way than what I have currently. It's turning into what I believe is a mess and I'm hoping that someone with more jquery knowledge can shine the light here. Here's my simple html form: <html> <head> <script type="text/javascript" src="jquery.js"></script> <script src="custom.js" type="text/javascript"></script> </head> <body> <input type="checkbox" class="class" id="1">First <input type="checkbox" class="class" id="2">Second <input type="checkbox" class="class" id="3">Third </body> </html> Here's the javascript I'm using with jquery v1.4.2 jQuery(document).ready(function() { // watches the events of all checkboxes $(":checkbox").click(function(){ if( // if both 1 and 2 are checked we don't want to enable Third until both are unchecked. (($('#1:checkbox').attr('checked'))&&($('#2:checkbox').attr('checked')))|| ((($('#1:checkbox').attr('checked'))&&($('#2:checkbox').attr('checked')))&&($('#3:checkbox').attr('disabled')))|| ((($('#1:checkbox').attr('checked'))||($('#2:checkbox').attr('checked')))&&($('#3:checkbox').attr('disabled'))) ){ // we don't want to do anything in the above events } else if( // handles the First check box (($('#1:checkbox').attr('checked'))||(!$('#1:checkbox').attr('checked')))|| // handles the Second check box (($('#2:checkbox').attr('checked'))||(!$('#2:checkbox').attr('checked'))) ){ // call the disableThird function disableThird(); } }); // handles enabling and disabling the Third checkbox function disableThird(){ var $checkbox = $('#3:checkbox'); $checkbox.attr('disabled', !$checkbox.attr('disabled')); }; }); For some reason checking #3 will disable it's self. I don't understand why. This works, but one of the requirements is that a non programmer should be able to edit and maintain this. Ideally it'd be great if he could just add new check boxes to the html and it would work. The class for these are define and as far as I know can't be changed. The last check box in the list of check boxes will disable if any of the ones above are selected. Like wise if the last check box is selected, it will disable all the ones above it. I haven't even begun writing and testing that portion as this is quickly becoming too complicated for a non programmer to handle. I myself am more of a PHP coder than a js, let alone jquery, coder. Any help would be greatly appreciated.

  Read the article

• Nagios plug-in check_snmp receives NO SNMP data from a CISCO Router

  - by Shehryar

  I have tried setting up Nagios on Ubuntu 10.10, successfully installed and can login to web interface, I am however stuck on configuring snmp or I am doing something wrong here, i have followed various sites / nagios wiki to setup configuration (cfg) files. When I check on the web interface, it gives the following error on one of my cisco router: Current Status: UNKNOWN (for 0d 2h 55m 56s) Status Information: SNMP problem - No data received from host CMD: /usr/bin/snmpget -t 1 -r 5 -m RFC1213-MIB -v 1 [authpriv] 192.168.1.1:161 ifOperStatus.1 On the command-line itself, when I type the following, it just sits there waiting and waiting : sudo /usr/local/nagios/libexec/check_snmp -H 192.168.1.1 -C Routers -o sysUpTime.0 When I type the following command : I get an OK /usr/bin/snmpget -v1 192.168.1.1:161 1.3.6.1.2.1.1.5.0 -c "Routers" I have configured SNMP properly on our cisco device as we can collect SNMP Data via two other monitoring tool (SolarWinds and Manage Engine), we are tempted towards Nagios as its opensource. Will be grateful if someone could assist in rectifying this situation and guide me with setting up nagios to monitor Cisco Routers, Switches and a Few Servers. We want to monitor Bandwidth, cpu utilization, uptime and other necessary counters. Will be grateful for your assistance Thanks for reading Shehryar

  Read the article

• MICR / Check printing

  - by drewk

  I want to print my own checks on blank stock from Quicken and QuickBooks. To do so, I need a virtual driver that intercepts the print output from Quicken formats the fields properly, and adds the MICR text at the bottom of the check. This is for Windows 7 or OS X. I have looked at the following: CHAX Works, but crashes a LOT. Not giving me confidence. It is also expensive. VersaCheck Looks promising but looks like it suffers severe feature bloat. I just want to print check and deposit slips, thank you. Ganson Is only for high volume really. It is also designed for batch use vs I just want to print to a virtual printer. More than $2500. GnuMICR is more of a science project. Not yet ready to use and has not been updated for years. There are a lot of solutions on the web, so please don't just google for me. I am looking for specific experience with good solid check printing solution. Thanks!!!

  Read the article

• MacBook Pro - Aquamacs - spell check

  - by peggy Li

  I have tried to use spell check for aquamac. I highlighted a region of the text. Then clicked Edit, then spell check region. I got the error message: Error : No word lists can be found for the language "en_US". Then I went to the website to download the following dictionaries: CocoAspell : I just clicked the download button. It was reported that the download was successful. However, when I tested it and highlighted a text region and clicked spell check. The same error message came out. Do I need to pull the downloaded .pkg to a certain place, such as the application folder, before I opened the .pkg? Or what else do I need to do make it work? I also downloaded the base package Aspell (for Intel) and the pre-built dictionaries as (as the instruction of the website), just the same way as point 1. I still got the same error message. Again, Do I need to pull the downloaded .pkg to a certain place, such as the application folder, before I opened the .pkg? Or what else do I need to do make it work? I would be greatly appreciated if someone could give me some help? Peggy Li

  Read the article

• check_snmp warning & critical thresholds with negative values

  - by Oesor

  I'm querying some signal level values measured in dBm, and the SNMP host on the remove device reports the values as negative values, ie, -90 dBm. However, check-snmp seems to be incapable of dealing with negative numbers as part of its threshold values. If I specify the values as part of a collection of OIDs, it accepts the syntax but converts the snmp value to positive, thus always generating a WARNING/CRITICAL result: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::AverageReceiveSNR.0,DEVICE-MIB::CurrentNoiseFloor.0 -w 10:,~:-85 -c 15:,~:-80 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::AverageReceiveSNR.0 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::AverageReceiveSNR.0 = INTEGER: 25 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::AverageReceiveSNR.0 response: = INTEGER: 25 Processing line 2 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP CRITICAL - 25 *97* | DEVICE-MIB::AverageReceiveSNR.0=25 DEVICE-MIB::CurrentNoiseFloor.0=97 If I run it with a single OID, it gives me an error that the format is incorrect: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -w ~:-85 -c ~:-80 -vvvv Range format incorrect And if I run it with no thresholds defined, it works properly and returns the right value. This makes the graphs correct, however it'll never generate a notification when out of range: root@ops-00:/usr/local/nagios/libexec# ./check_snmp -H 192.168.1.100 -o DEVICE-MIB::CurrentNoiseFloor.0 -vvvv /usr/bin/snmpget -t 1 -r 5 -m ALL -v 1 [authpriv] 192.168.1.100:161 DEVICE-MIB::CurrentNoiseFloor.0 DEVICE-MIB::CurrentNoiseFloor.0 = INTEGER: -97 Processing line 1 oidname: DEVICE-MIB::CurrentNoiseFloor.0 response: = INTEGER: -97 SNMP OK - -97 | DEVICE-MIB::CurrentNoiseFloor.0=-97 What am I doing wrong here? How would I, for example, generate a CRITICAL when the noise floor is -80 dBm or higher, a WARNING when it's -85 to -80 dBm, and an OK when -85 dBm or lower? Do I have to write my own SNMP plugins when dealing with negative values?

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• MS Word custom dictionary making spellcheck slow - ideas?

  - by ezuk

  I have a user who edits technical materials. She uses MS Word's Custom Dictionary all the time for spelling; it has grown very large, and is now making spell check very slow. All of the advice I've read online says to disable the custom dictionary. This is an easy solution, but is not workable for the user, because she actually needs this dictionary. So, is there any way to optimize the custom dictionary and/or Word itself, so that a large dictionary file doesn't slow things down quite so badly? Many thanks. Update after suggestions: I ran contig on the file, and it reports just 1 frag, so that's not the issue I think. The file is 9.95KB -- 1,117 lines, each consisting of just a single word. I viewed the file using Notepad and none of the lines seems corrupted, strange, or overly long (no line seems to be over 10 chars or so). Both of your suggestions were helpful so I will upvote both; any further tips would be most welcome.

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >