Search Results

Search found 1106 results on 45 pages for 'lo wai lun'.

Page 9/45 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

  • debian lenny : problem modifying static ip

    - by supertiti
    hello all, i'm trying to change a static ip assigned to a debian VM. I modified the /etc/network/interfaces file but my debian doesn't seem to like the new settings currently the machine's ip is set to 192.168.1.136 and i want the machine's ip to be set to 192.168.1.8 here's my modified /etc/network/interfaces : auto lo iface lo inet loopback allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.1.8 gateway 192.168.1.1 netmask 255.255.255.0

    Read the article

  • USB flash module giving errors

    - by vshenoy
    Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

    Read the article

  • UPDATE from SELECT complains about more that one value returned

    - by Álvaro G. Vicario
    I have this data structure: request ======= building_id lot_code building ======== building_id lot_id lot === lot_id lot_code The request table is missing the value for the building_id column and I want to fill it in from the other tables. So I've tried this: UPDATE request SET building_id = ( SELECT bu.building_id FROM building bu INNER JOIN lot lo ON bu.lot_id=lo.lot_id WHERE lo.lot_code = request.lot_code ); But I'm getting this error: Subquery returned more than 1 value. This is not permitted when the subquery follows =, !=, <, <= , , = or when the subquery is used as an expression. Is it due to wrong syntax? The data model allows more than one building per lot but actual data doesn't contain such cases so there should be at most one building_id per lot_code.

    Read the article

  • ifup eth0 failed in Ubuntu 11.10 and Ubuntu 10.04.3

    - by Ajay
    ifup eth0 failed to bring up eth0 First, I have set static ip using the below commands: Commands: ifdown eth0 ifconfig eth0 X.X.X.X netmask 255.255.252.0 up route add default gw X.X.X.X I was successful in setting up static ip X.X.X.X and I could see the same in the output of command "ifconfig". Now I am trying to revert network back to dhcp using the below commands: Commands: ifdown eth0 ifup eth0 Output : RTNETLINK answers: File exists ssh stop/waiting ssh start/running, process 1524 ifup eth0, failed to bring back dhcp. Contents of /etc/network/interfaces root@bdhcp396:~# cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp Is this a bug in Ubuntu 11.10/10.04.3? I see a similar bug raised - https://bugs.launchpad.net/ubuntu/+source/ifupdown/+bug/876829

    Read the article

  • Al abrir archivo desde navegador se abre el directorio

    - by user67662
    al descargar un archivo a través de cualquier navegador (chrome, firefox, etc) e intentar abrirlo directamente, en vez de abrirse el archivo se abre el directorio en que se descargó. lo mismo me sucedió al intentar abrir un archivo desde el dash de gnome-shell. Esto sólo me sucede con los accesos directos a los archivos, cuando estoy dentro de nautilus se abre el archivo sin problemas. he intentado en distintos entornos de escritorio, el que uso más constantemente es Gnome-Shell, bajo Ubuntu 12.04 ¿cómo lo puedo solucionar? Gracias!

    Read the article

  • What do the 4 keyboard input method systems in 10.04 mean?

    - by Android Eve
    I am trying to install another language support (in addition to the default US). Checking that language checkbox in "Install / Remove Languages..." wasn't too difficult. :) But now I want to add keyboard support, too, for that language. Again, I am prompted with a nice listbox with the following 4 options: none ibus lo-gtk th-gtk But I have no idea what these mean. I googled "ubuntu 10.04 keyboard input method system none ibus lo-gtk th-gtk" but all I could find was descriptions of problems, not an actual definition. Could you please point me to a webpage where I can learn about the meanings of these 4 different methods and +'s and -'s of each?

    Read the article

  • Estudio de caso: CFO de At&T le apunta a la tecnología para transformar las Finanzas Globales

    - by RED League Heroes-Oracle
    AT&T es una de las pocas multinacionales modernas que han participado de todas las etapas anteriores de la innovación de las telecomunicaciones, de Alexander Graham Bell como inventor solitario, a Bell Labs, a los lanzamientos acelerados en las fundiciones de AT&T. La tecnología es el corazón de todo lo que AT&T hace, incluyendo sus inversiones en innovaciones tecnológicas para permitir que las finanzas de AT&T trabajen más estratégicamente con los negocios para asegurar que las inversiones en las iniciativas de crecimiento sean exitosas. Según John Stephens, Vicepresidente Ejecutivo y director financiero de AT&T, la empresa ha trazado un plan de inversión de tres años para mejorar y aumentar sus redes IP de banda ancha alámbricas e inalámbricas. El plan incluye la implementación del servicio 4G LTE para 300 millones de personas en los Estados Unidos, expansión de IP de banda ancha de alta velocidad a unos 57 millones de hogares de clientes y una expansión de la fibra a 1 millón de clientes corporativos adicionales en su área de servicio de telefonía fija. "La necesidad de velocidad es mayor que nunca, y este proyecto es nuestro paso hacia la innovación para ofrecer tal velocidad," dice Stephens. Como AT&T moderniza su infraestructura global, sus procesos operacionales se hacen tan poderosos como su red. Ha sido una tarea grande y compleja, pero Stephens se complace al decir que el departamento de finanzas de AT&T ha adoptado su papel de catalizador corporativo. Empezó con un concepto simple: "Vamos a hacer que todos hablen en el mismo idioma". Esto llevó a la consolidación de sistemas financieros heredados de las empresas adquiridas. No fue una tarea sencilla, dado que la empresa pasó por más de cinco adquisiciones importantes y un sinfín de otras transacciones. En 2007, AT&T tenía 17 aplicaciones apenas en la función de cuentas por pagar. Hoy, el número se ha reducido a dos. Asimismo, hubo 50 sistemas de reportes gerenciales oficiales y ahora hay tres, con planes de excluir uno de ellos. Al tener un único lenguaje volcado a las Finanzas en toda la empresa, el equipo de finanzas de AT&T ha eliminado las varias versiones de los mismos datos, reduciendo la posible confusión en las discusiones y en las decisiones de estrategia de negocios. Estos pasos también han reducido los costos y aceleraron la toma de decisiones. "Lo lindo de los sistemas es que permiten que la gente talentosa con habilidades analíticas usen su tiempo en esa zona, en vez de gastar tiempo en recolección, agregación y organización de los datos," señala Stephens. "Tenemos un proceso eficiente y eficaz que hace que nosotros, dejemos a la gente libre para dedicarse a aquello en que son realmente buenos. Y tenemos un equipo de alta calidad y ellos están en su mejor punto cuando son capaces de hacer su función para apoyar a la unidad de negocio”AT&T es una de las pocas multinacionales modernas que han participado de todas las etapas anteriores de la innovación de las telecomunicaciones, de Alexander Graham Bell como inventor solitario, a Bell Labs, a los lanzamientos acelerados en las fundiciones de AT&T. La tecnología es el corazón de todo lo que AT&T hace, incluyendo sus inversiones en innovaciones tecnológicas para permitir que las finanzas de AT&T trabajen más estratégicamente con los negocios para asegurar que las inversiones en las iniciativas de crecimiento sean exitosas.  Según John Stephens, Vicepresidente Ejecutivo y director financiero de AT&T, la empresa ha trazado un plan de inversión de tres años para mejorar y aumentar sus redes IP de banda ancha alámbricas e inalámbricas. El plan incluye la implementación del servicio 4G LTE para 300 millones de personas en los Estados Unidos, expansión de IP de banda ancha de alta velocidad a unos 57 millones de hogares de clientes y una expansión de la fibra a 1 millón de clientes corporativos adicionales en su área de servicio de telefonía fija. "La necesidad de velocidad es mayor que nunca, y este proyecto es nuestro paso hacia la innovación para ofrecer tal velocidad," dice Stephens. Como AT&T moderniza su infraestructura global, sus procesos operacionales se hacen tan poderosos como su red. Ha sido una tarea grande y compleja, pero Stephens se complace al decir que el departamento de finanzas de AT&T ha adoptado su papel de catalizador corporativo. Empezó con un concepto simple: "Vamos a hacer que todos hablen en el mismo idioma". Esto llevó a la consolidación de sistemas financieros heredados de las empresas adquiridas. No fue una tarea sencilla, dado que la empresa pasó por más de cinco adquisiciones importantes y un sinfín de otras transacciones. En 2007, AT&T tenía 17 aplicaciones apenas en la función de cuentas por pagar. Hoy, el número se ha reducido a dos. Asimismo, hubo 50 sistemas de reportes gerenciales oficiales y ahora hay tres, con planes de excluir uno de ellos. Al tener un único lenguaje volcado a las Finanzas en toda la empresa, el equipo de finanzas de AT&T ha eliminado las varias versiones de los mismos datos, reduciendo la posible confusión en las discusiones y en las decisiones de estrategia de negocios. Estos pasos también han reducido los costos y aceleraron la toma de decisiones. "Lo lindo de los sistemas es que permiten que la gente talentosa con habilidades analíticas usen su tiempo en esa zona, en vez de gastar tiempo en recolección, agregación y organización de los datos," señala Stephens. "Tenemos un proceso eficiente y eficaz que hace que nosotros, dejemos a la gente libre para dedicarse a aquello en que son realmente buenos. Y tenemos un equipo de alta calidad y ellos están en su mejor punto cuando son capaces de hacer su función para apoyar a la unidad de negocio”

    Read the article

  • Why Wifi no longer works 12.04.1

    - by Roger
    starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

    Read the article

  • Two Wifi Icons in Panel [Solved]

    - by Alex
    I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

    Read the article

  • Oracle lanza una comunidad específica para hardware

    - by Eloy M. Rodríguez
    Para aquellos que aún no lo conozcan, quiero presentarles un grupo de interés creado por la compañía en Facebook con el nombre de Oracle Hardware Social Media Hub con el fin de ofrecer un lugar de reunión en la red en el que encontrar a miles de expertos, clientes, partners y reconocidos líderes de Oracle para debatir y descubrir lo último de Oracle. Allí encontrará una pionera aplicación de preguntas y respuestas denominada Pregunte al Experto de Oracle, en donde podrá formular preguntas, aportar comentarios e incluso ser premiado por sus aportaciones especializadas con el título de líderes reconocidos. En el Hardware Hub se podrá, entre otras cosas: Obtener contenidos exclusivos, solamente para los miembros Compartir sus conocimientos y experiencias con una comunidad global Comunicarse con expertos de Oracle en un entorno informal Descubrir métodos innovadores para optimizar el rendimiento de su hardware Acceder a contenidos en su idioma, incluyendo información de eventos, Webcasts, informes técnicos y mucho más.

    Read the article

  • Install VLC 2.0.7 in CentOS 6.4?

    - by raaz
    I am keep failing in the installation process I have tried. I have started process as follows. yum install gcc dbus-glib-devel* lua-devel* libcddb wget http://download.videolan.org/pub/videolan/vlc/2.0.7/vlc-2.0.7.tar.xz tar -xf vlc-2.0.7.tar.xz && cd vlc-2.0.7 ./configure in the configure I am getting the error as follows configure: WARNING: No package 'libcddb' found: CDDB access disabled. checking for Linux DVB version 5... yes checking for DVBPSI... no checking gme/gme.h usability... no checking gme/gme.h presence... no checking for gme/gme.h... no checking for SID... no configure: WARNING: No package 'libsidplay2' found (required for sid). checking for OGG... no configure: WARNING: Library ogg >= 1.0 needed for ogg was not found checking for MUX_OGG... no configure: WARNING: Library ogg >= 1.0 needed for mux_ogg was not found checking for SHOUT... no configure: WARNING: Library shout >= 2.1 needed for shout was not found checking ebml/EbmlVersion.h usability... no checking ebml/EbmlVersion.h presence... no checking for ebml/EbmlVersion.h... no checking for LIBMODPLUG... no configure: WARNING: No package 'libmodplug' found No package 'libmodplug' found. checking mpc/mpcdec.h usability... no checking mpc/mpcdec.h presence... no checking for mpc/mpcdec.h... no checking mpcdec/mpcdec.h usability... no checking mpcdec/mpcdec.h presence... no checking for mpcdec/mpcdec.h... no checking for libcrystalhd/libcrystalhd_if.h... no checking mad.h usability... no checking mad.h presence... no checking for mad.h... no configure: error: Could not find libmad on your system: you may get it from http://www.underbit.com/products/mad/. Alternatively you can use --disable-mad to disable the mad plugin. [root@localhost vlc-2.0.7]# So I went to libmad http location and downloaded it and while doing make it gave me the errors.There are no errors at ./configure with libmad but make not going through. [root@localhost libmad-0.15.0b]# make (sed -e '1s|.*|/*|' -e '1b' -e '$s|.*| */|' -e '$b' \ -e 's/^.*/ *&/' ./COPYRIGHT; echo; \ echo "# ifdef __cplusplus"; \ echo 'extern "C" {'; \ echo "# endif"; echo; \ if [ ".-DFPM_INTEL" != "." ]; then \ echo ".-DFPM_INTEL" | sed -e 's|^\.-D|# define |'; echo; \ fi; \ sed -ne 's/^# *define *\(HAVE_.*_ASM\).*/# define \1/p' \ config.h; echo; \ sed -ne 's/^# *define *OPT_\(SPEED\|ACCURACY\).*/# define OPT_\1/p' \ config.h; echo; \ sed -ne 's/^# *define *\(SIZEOF_.*\)/# define \1/p' \ config.h; echo; \ for header in version.h fixed.h bit.h timer.h stream.h frame.h synth.h decoder.h; do \ echo; \ sed -n -f ./mad.h.sed ./$header; \ done; echo; \ echo "# ifdef __cplusplus"; \ echo '}'; \ echo "# endif") >mad.h make all-recursive make[1]: Entering directory `/home/raja/Downloads/libmad-0.15.0b' make[2]: Entering directory `/home/raja/Downloads/libmad-0.15.0b' if /bin/sh ./libtool --mode=compile gcc -DHAVE_CONFIG_H -I. -I. -I. -DFPM_INTEL -DASO_ZEROCHECK -Wall -march=i486 -g -O -fforce-mem -fforce-addr -fthread-jumps -fcse-follow-jumps -fcse-skip-blocks -fexpensive-optimizations -fregmove -fschedule-insns2 -fstrength-reduce -MT version.lo -MD -MP -MF ".deps/version.Tpo" \ -c -o version.lo `test -f 'version.c' || echo './'`version.c; \ then mv -f ".deps/version.Tpo" ".deps/version.Plo"; \ else rm -f ".deps/version.Tpo"; exit 1; \ fi mkdir .libs gcc -DHAVE_CONFIG_H -I. -I. -I. -DFPM_INTEL -DASO_ZEROCHECK -Wall -march=i486 -g -O -fforce-mem -fforce-addr -fthread-jumps -fcse-follow-jumps -fcse-skip-blocks -fexpensive-optimizations -fregmove -fschedule-insns2 -fstrength-reduce -MT version.lo -MD -MP -MF .deps/version.Tpo -c version.c -fPIC -DPIC -o .libs/version.lo cc1: error: unrecognized command line option "-fforce-mem" make[2]: *** [version.lo] Error 1 make[2]: Leaving directory `/home/raja/Downloads/libmad-0.15.0b' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/home/raja/Downloads/libmad-0.15.0b' make: *** [all] Error 2 how can i resolve the issue and install VLC in my Centos ? I am using CentOS 6.4 . Thank you.

    Read the article

  • Unable to set default gateway

    - by GrandMasterFlush
    I'm running Ubuntu server via Hyper-V and have successfully installed it but seem unable to ping the server or ping any other machines on the network from the server. After doing a bit of reading I've noticed that the default gateway isn't set but when I try and set it I keep getting error messages which I can't understand. From this article I've tried ip route add default via 10.0.10.200 Which reports: RTNETLINK answers: Operation not permitted If I try running it prefixed with sudo but it reports: `RNETLINK answers: No such process I've editted /etc/network/interfaces but when I start the machine and type netstat -nr there is nothing listed. Can anyone tell me where I'm going wrong please? EDIT : /etc/network/interfaces contains: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp

    Read the article

  • How did Ubuntu know my WPA Key?

    - by nebukadnezzar
    I've recently moved my /home to another computer (keeping all configuration files), with a fresh installation of Ubuntu 10.10. After Installation I've installed wicd and ndiswrapper, to get my Internet Connection up and running. However, after changing /etc/network/interfaces from auto lo iface lo inet loopback To auto wlan0 iface wlan0 inet dhcp and running sudo /etc/init.d/networking restart to get wlan0 set up, wicd just suddenly connected... to my modem. Without supplying any information about the modem whatsoever. Of course wicd creates a local directory at ~/.wicd/, but that directory is empty, and the temporary global configuration at /var/lib/wicd/configurations/ didn't exist due to fresh installation of ubuntu. So what's the deal? Where did wicd get the ESSID and the WPA Key? There hasn't been any activity in this question, but it's still open (and even worth some rep)!

    Read the article

  • Ubuntu Server Cannot Route to the Internet

    - by ejes
    I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

    Read the article

  • setup dhcp server - "Job failed to start"

    - by jdicarreira
    I have an eth0 and eth1, eth0 has dynamic ip and on eth1 i setup static ip: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.10.0.1 netmask 255.0.0.0 gateway 10.10.0.1 ` and then i setup the "isc-dhcp-server" with the fowling command: INTERFACES="eth1" Finally... I went to this one "dhcpd.conf", with the fowling comand: default-lease-time 650; max-lease-time 79520; option subnet-mask 255.0.0.0; option broadcast-address 10.10.0.255; option routers 10.10.0.2; subnet 10.10.0.0 netmask 255.0.0.0 { range 10.10.0.10 10.10.0.250; } When I try to "sudo /etc/init.d/isc-dhcp-server start", I get "start: Job failed to start" Anyone knows whats wrong? :/

    Read the article

  • Better Embedded 2012

    - by Valter Minute
    Il 24 e 25 Settembre 2012 a Firenze si svolgerà la conferenza “Better Embedded 2012”. Lo scopo della conferenza è quello di parlare di sistemi embedded a 360°, abbracciando sia lo sviluppo firmware, che i sistemi operativi e i toolkit dedicati alla realizzazione di sistemi dedicati. E’ un’ottima occasione per confrontarsi e, in soli due giorni, avere una panoramica ampia dall’hardware a Linux, da Android a Windows CE, dal .NET microframework a QT, senza troppi messaggi commerciali e con un’ottima apertura sia alle tecnologie commerciali che a quelle free e open source. Io parteciperò come speaker, parlando di Windows CE, ma anche come spettatore interessato a molte delle track di un programma che si va popolando e diventa mano a mano più interessante. Se volete cogliere l’occasione per visitare Firenze (che già sarebbe un motivo più che sufficiente!) e parlare di embedded, contattatemi perchè come speaker posso fornire un codice sconto che vi farà risparmiare un 20% sul prezzo della conferenza (che già è vantaggiosissimo, vista la quantità di contenuti dedicati all’embedded). Arrivederci a Firenze!

    Read the article

  • /etc/network/interfaces doesn't always take affect

    - by user1221444
    For some reason my eth0 does not have internet on reboot sometimes. I am using a static ip. I can ping my gateway, but I am unable to ping dns servers, or anything out of my network. It seems that when my internet does work(Usually but just restarting enough times), my /etc/resolv.conf has a nameserver in it. It is empty when I have no internet access. I believe something is overwriting my interfaces settings sometimes on boot. Any help would be appreciated. I am running Ubuntu Server 12.04 64bit /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.213.192.234 netmask 255.255.255.248 network 173.213.192.232 broadcast 173.213.192.239 gateway 173.213.192.233 dns-nameservers 8.8.8.8 auto eth1 iface eth1 inet static address 10.0.0.106 netmask 255.255.255.0 gateway 10.0.0.1

    Read the article

  • Two Wifi Icons in Panel

    - by Alex
    I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

    Read the article

  • dhcp configuration not working ubuntu 11.10

    - by Vivek Pradhan
    I am usually behind a proxy server in college so I connect to the ethernet or wifi using manual IPv4 addresses only inside college. I have been trying really hard to get the internet work at home, there is no proxy and I have set the network to use automatic dhcp. It seems like it is not able to connect to the port, It gets disconnected after some time automatically and then tries to reconnect. The same thing is happening with wifi networks also, after some time i see a pop up asking for authentication and ultimately its not able to connect. What might be the problem here. I looked up some similar questions and checked the /etc/network/interfaces file and looks like this: auto lo iface lo inet loopback I have no idea what those lines mean but there is no configuration for eth0 or wlan0. Any help is deeply appreciated. Ubuntu loses it charms due to these small glitches.

    Read the article

  • ifconfig not showing all IPs bound to the machine

    - by pankaj sharma
    I have configured multiple IP addresses on a ubuntu box, but when I run ifconfig it shows just one of them. I am able, however, to ping all other adresses assigned to this machine. /etc/network/interface contents: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.202.11 netmask 255.255.255.0 network 192.168.202.0 broadcast 192.168.202.255 gateway 192.168.202.1 # dns-* options are implemented by the resolvconf package, if installed dns-search idil.dz1.da auto eth0:1 iface eth0:1 inet static address 192.168.202.12 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 192.168.202.13 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 192.168.202.14 netmask 255.255.255.0 auto eth0:4 iface eth0:4 inet static address 192.168.202.15 netmask 255.255.255.0 auto eth0:5 iface eth0:5 inet static address 192.168.202.16 netmask 255.255.255.0 but the output of the ifconfig is only: 192.168.202.11

    Read the article

  • When Ubuntu Server restarts eth0 Doesn't come back up

    - by JoelGsus
    Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

    Read the article

  • wlan0 (WPA2) doesn't work when configured manually

    - by 71GA
    I have been trying to reconfigure my eth0 and wlan0 interfaces by editing /etc/network/interfaces file as folows: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.11 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 dns-nameservers 193.2.1.66 auto wlan0 iface wlan0 inet static address 192.168.1.10 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 dns-nameservers 193.2.1.66 wpa-driver wext wpa-ssid lausi wpa-ap-scan 2 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk 8952a447c860d13847ba1cabd15314ba9caf2fb207f19598f90c43fcd43c0d97 But my wireless doesnt work when i use command /etc/init.d/networking restart and when i do this i get an error: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... RTNETLINK answers: File exists Failed to bring up eth0. ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument RTNETLINK answers: File exists Failed to bring up wlan0. Although it clearly states that my eth0 interface couldn't be brought to life it is working! But i cant say this for the wlan0 interface which doesn't even work if i unplug internet cable and again use command /etc/init.d/networking restart. This seems weird to me... When i use ìfconfig -a command i get an output which confirms that wlan0 isnt working and eth0 is. ziga@ziga-cq56:/etc/network$ ifconfig -a eth0 Link encap:Ethernet HWaddr 60:eb:69:6f:5f:69 inet addr:192.168.1.11 Bcast:192.168.1.13 Mask:255.255.255.0 inet6 addr: fe80::62eb:69ff:fe6f:5f69/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6764 errors:0 dropped:0 overruns:0 frame:0 TX packets:6641 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5932190 (5.9 MB) TX bytes:1331846 (1.3 MB) Interrupt:42 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1759 errors:0 dropped:0 overruns:0 frame:0 TX packets:1759 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:107772 (107.7 KB) TX bytes:107772 (107.7 KB) wlan0 Link encap:Ethernet HWaddr 70:f3:95:e7:57:cc inet addr:192.168.1.10 Bcast:192.168.1.12 Mask:255.255.255.0 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) How can i make my wlan0 interface work? It had been working previously with network manager and wicd...

    Read the article

  • Cannot connect to ethernet port

    - by Jnir
    I'm running Ubuntu 12.04 LTE. I'm trying to connect via ethernet for the first time but have had no success. Ifconfig eth0 returns: eth0 Link encap:Ethernet HWaddr: 00:01:2e:3f:f1:a0 inet6 addr: fe80::201:2eff:fe3f:f1a0 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:68 errors:0 dropped:0 overruns:0 frame:0 TX packets:183 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8374 (8.3 KB) TX bytes:42944 (42.9KB) Interrupt:16 Base address:0x6c00 /etc/network/interfaces has auto lo iface lo inef loopback auto eth0 iface eth0 inet dhcp sudo /etc/init.d/networking prints: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... Failed to bring up eth0 [OK]

    Read the article

  • Static IP breaks Network connection

    - by Pasquale Tedesco
    I am somewhat new to Linux. I am setting up a Web server and installed Ubuntu server 14.04 on an vSphere ESXi 5.5 host. I am connecting perfectly fine to the internet when using DHCP but when I apply my Static settings I loose the ability to connect to websites. Whats weird is I can Ping google.com but if I try wget gooogl.com it hangs at connecting to google.com (google.com):173.194.43.32:80 and I get "failed: connection refused" But if I am set to DHCP the connection resolves perfectly. Thanks # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 #iface eth0 inet dhcp iface eth0 inet static address 10.1.2.25 gateway 10.1.2.2 netmask 255.255.255.0 search tsig.com dns-nameservers 10.1.2.13 10.1.2.30

    Read the article

  • Can't boot - "Waiting for Network Configuration"

    - by user213017
    After an update on 13.10, my PC won't boot Ubuntu any longer. It displays the infamous "Waiting for Network Configuration" message and then hangs. I can go into recovery mode, and choose "Start networking" and then go to a root prompt, and that works fine. Ping works. /etc/network/interfaces contains just the two lines "auto lo" and "iface lo inet loopback". I've double-checked that my network is working, the cable is working (it works on another PC) and the network card seems to indicate a connection. Any suggestions on how to get my PC booted again? Right now I'm limited to a root shell prompt.

    Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >