Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 9/391 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• Getting wireless N to work on Dell Vostro 3300?

  - by luisfpg

  I have a Dell Vostro 3300, which has a Broadcom BCM4313 wireless. The point is that I cannot make it work in N mode. NetwotkManager applet says I'm on 54 Mbit/s. Of course, my wireless router is N capable. I've double checked. Anyone knows what to do? Here is the output for lspci -v: 12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Device 0010 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: wl Kernel modules: wl, brcm80211 Thanks a lot.

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• How do I get my RTL8192ce based wireless device working properly?

  - by JonnyTruelove

  I am using the rtl8192cu chipset (on a Belkin wireless USB adapter N300) combined with 64 bit architecture and the 3.8 kernel. Some of you may know that this doesn't work. I tried this fix - RTL8188CU USB Network Adaptor on ubuntu 13.04 and now my internet is super slow. I am totally new to Ubuntu and I am concerned I do not have the right driver. The "stock" driver was the RTL8192cu, but it didn't connect 99% of the time and if it did the upload speed was higher than the download. Right now I am connecting through my laptop with a crossover cable, so my internet connection is just fine in my apartment. Relevant output from lsusb is here: Bus 002 Device 002: ID 050d:2103 Belkin Components F7D2102 802.11n N300 Micro Wireless Adapter v3000 [Realtek RTL8192CU] (bonus question: is that [050d:2103] the actual physical address straight from the hardware? Or does it change when I put different drivers on it? I am concerned I do not have the right driver)

  Read the article

• Wireless Router will not allow connection

  - by Chris

  I am working with a RangeMax(TM) Wireless Router WPN824 v2, and it will not allow a wireless connection nor a wired connection. I am at an actual lost, with no way into the router I cannot test settings. I have unplugged it, left it off for a 32 hours, and reset it with no luck. Any ideas? Could the router just be done-zo?

  Read the article

• Using wireless interface in guest OS with bridged network in VMware fusion 3

  - by Chetan

  I'm running Ubuntu in Snow Leopard with VMware fusion 3, and I want to be able to access the wireless network on eth1 within Ubuntu so I can run tools like aircrack-ng. However, the bridged network that VMware sets up connects my Airport interface in Mac to the wired interface eth0 in Ubuntu. How do I set it up so that the Airport interface is connected to the wireless interface eth1 in Ubuntu?

  Read the article

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• Troubleshooting wireless connection problem / site survey?

  - by johnnyb10

  I just started in the IT department of a small company (200 users) and it's clear that one of the main problems that is driving everyone crazy is the spotty nature of the wireless connectivity throughout the office, particularly in certain conference rooms. This is a huge problem because the connection often drops during important presentations to clients. I was hired to help ease the load on the existing IT admin, who has done a great job, but is overloaded with many other tasks to deal with. So I would like to try to help out with this wireless issue. I am looking for advice on the best way to solve this problem--a realistic troubleshooting methodology that does not require me to spend any money. So far, I've experimented with Ekahau Heat Mapper, which is free and helps create a site survey. But I'm not exactly sure what I'm looking for or if there are other programs/tools/methods I should try as well. Any advice would be greatly appreciated. [Some background: The wireless setup consists of an HP ProCurve Mobility MSM (710?) controller that controls 10 access points throughout the building. There are three virtual wireless networks configured on the controller: one seems to be a default that cannot be changed, one is for internal employees and authenticates via Active Directory, and the third is a guest network for visitors. When I use HeatMapper, these show up as three different SSIDs, with different MAC addresses, all on the same channel. At first I thought maybe this would cause interference, but this seems to be the way the controller works;apparently, it automatically configures the channels to avoid interference from the other APs on the network.]

  Read the article

• Is browser based wireless authentication secure?

  - by johnnyb10

  Our wireless network previously used a preshared WPA/WPA2 key for guest access, which allows them access to the Internet. (Our employee access uses 802.1x authentication). We just had a wireless consultant come in to fix various wireless issues we had; one of the things he wound up doing was changing our guest access to HTML-based instead of the preshared key. So now that guest SSID is open (instead of using WPA) and users are presented with a browser-based login screen before they can get on the Internet. My question is: Is this an acceptable method from a security standpoint? I would assume that having an open network is necessarily a bad idea, but the consultant said that the traffic is still using PEAP, so it's secure. I didn't get a chance to question him further on this because we ran late and a bunch of other things came up. Please let me know what you think about the advantages/disadvantages of using HTML-based wireless authentication as opposed to using a preshared WPA key. Thanks...

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Can't find PC on network

  - by Simon Verbeke

  I just got myself a new laptop, and set it up. It is connected to the wireless internet in my home. I then wanted to create a homegroup between the laptop and my desktop, but they can't find each other. Probably because the desktop has a wired connection to the router and the laptop is connected to a wireless access point. The router and the AP are connected to a switch in the middle by cable. A sketch of the network: Laptop - - - Wireless Access Point ----- Switch ----- Router ----- Desktop ^ ^ ^ ^ Wireless Wired Wired Wired They both point to the same gateway and DHCP-server (on 192.168.0.1). And I can ping to that address from both PCs. When I try to ping either of the PCs the pings time out. The subnets are also the same (255.255.255.0) and the IPs are in the same range (192.168.0.114 laptop, 192.168.0.205 desktop). So I don't really understand what I need to do to be able to access either computer from the other. The weird thing is that Synergy (to use mouse and keyboard over the network) works, just by using the IPs assigned to both PCs. The acces point is a linksys WAP54g, but I'm unsure of the Router, it has a custom casing from our ISP and hides any clues for identifying the product. I'm going to google a bit so I can add that info later. Both PC's are Windows 7 64 bit. The desktop is Ultimate, the laptop Professional.

  Read the article

• Home networking problem between power line communication and Ethernet

  - by pixeline

  My network runs through the electrical wiring of the house and is organised as such: Groundfloor: an ADSL+network switch, using DHCP (address : 172.19.3.1) (Mac) PCs connected via an electrical adapter (model: D-Link DHP-200) (1 per PC) First Floor: 1 switch (8 ports) connected via an electrical adapter (model: D-Link DHP-200) (address unknown) 2 Mac PCs connected (via RJ45 network wires) to that router using DHCP The Problem On the first floor, file tranfers between PCs are fast and perfect. But if I try to transfer files from or to a computer on the ground floor, the speed is slow and eventually the transfer dies out. The Question So I suspect the 1st floor switch is creating some kind of barrier (firewall?) preventing external PCs from accessing the PCs it is connected to? Am I right and if so, how could I disable that barrier?

  Read the article

• Any free networking lab?

  - by Gok Demir

  I want to study network. But I don't have an access to a sample network (routers, DNS, IP4, IP6 windows linux mixed heterogenous system). Do you know any online network to study (Free as possible). Is it possible to simulate network topologies with a single PC using virtual machine. If so could you guide me?

  Read the article

• win xp wifi networking

  - by user3485532

  I have 2 pcs with win xp and a wifi router ( without outgoing internet connection )...my job was to connect them over wifi to share some files. router was properly configured, both computers connected to wifi without problems, but when I tried to network them I could not see them in workgroup...i changed their names and added them to same workgroup but i couldn't connect pc1 to pc2 ( i could ping router from each pc but pinging other computer resulted in ping timeout) ..now i cant figure out why this is not working since I've done this before on more complex networks and it should work but...( maybe I have gremlins hiding somewhere..) edit1: Firewall is down on both machines( I disengaged it in both control panel and in services) and folder sharing and permissions are ok.. edit2: I know about Ad Hoc network ( wlan-to-wlan, without router/switch ) but that's not what I am trying to accomplish here :)

  Read the article

• Networking Logs for MAC Addresses

  - by NetworkGuy

  I wanted to ask a multi-part question. Does Comcast Cable Internet services record MAC Addresses of the Router behind the cable modem. I know they record it for the modem itself. But is there a way for the Modem/Comcast to relay and keep logs of the MAC ID of the Router itself? Then does a windows operating system Log the MAC ID of the Router when its connected to it? If so where do I locate and purge this? Please let me know all areas where it is Logged within the operating system. Thank you!

  Read the article

• System can't sleep, can't shutdown (might be networking related)

  - by Kevin Q

  I speculate it's networking related since I could only shut down my system if I do /etc/init.d/networking stop first. If I tried to put the system to sleep, it disconnect the network then reconnect it automatically, never goes to sleep. I uninstalled the network manager, then /etc/init.d/networking stop will not help shutdown the system anymore. When I boot into the OS, there were some warning about Unknown job:S20acpid,S20network-interface, S20network-manager . I got some advices to do update-rc.d -f to remove all those script, which I am not certain if it's right thing to do. The messages are gone but the problem remains. When I tried to restart, I used to get this message It doesn't seem to be the modem manager since I later removed it. Once upon a time, the fronze shutting down/restarting can be restarted when I presses Ctrl+Alt+Delete, and it says something like networking is stopped externally. If I log in single user mode, and shutdown or reboot, it show this screen I also tried GRUB_CMDLINE_LINUX_DEFAULT = "acpi=force" This is a Ubuntu 12.04 running on Thinkpad T520, not new installation, no such problems occurred before.

  Read the article

• Networking problems in VMWare with wireless bridge

  - by Robert Koritnik

  Barebone data: virtualization: VMWare Workstation 6.5 (latest) Host: Windows Server 2008 x64 Guest: Windows Server 2008 x86 Host network adapter: wireless Guest network adapter 1: over Bridge VMNet (automatic) Guest network adapter 2: over Host only VMNet Problem When I surf the net within VM my internet connection just gets stalled (not dropped). It doesn't experience any timeout whatsoever, it just stops downloading/communicating. For instance: I start downloading a file with a browser (IE/FF/CR doesn't matter) and I have to pause/restart download when speed drops to 0. I could wait indefinitelly but connection won't pickup automatically. What did I miss in my network configuration? Update 1 I've tested this in various combinations. This works fine when host is connected via Ethernet. But when connected via Wifi, the connection on the guest works as previously described. It connects fine. It gets a valid IP from DHCP... Everything is cool as long as you don't start doing some intensive network traffic (ie. download a 2MB file) In this case it starts downloading and stops after a while. Speed just drops to 0B/s... Sometimes it picks up back, sometimes it doesn't. Connection still stays and works. I can ping around with no problem.

  Read the article

• How do I bridge my wireless to my wired connection?

  - by gatoatigrado

  I want to bridge the wireless connection with the wired connection. The wireless is the host and the wired is the client, so to speak. Internet sharing (inet <--> wifi <--> ethernet) I tried to bridge my ethernet connection by going to network manager edit connections wired edit IPv4 settings shared to other computers Screenshots However, it seems to automatically disconnect half a second after it says "connection established"! edit 2 got the network manager logs, it seems the address is in use. See http://pastebin.com/DjqRshxW , line 45. nm-tool output is here: http://pastebin.com/x5Aci5V1 . I tried firestarter, as mentioned in another thread, and no luck. I don't have time to bother with a dozen command line tricks, unless is copy & pasting a shell script... so please suggest ways that use GUIs and/or won't leave my computer in a confused state (e.g. disabling network manager, manually connecting to a WPA network, installing brutils, etc.). edit: one idea that would work, if it's possible -- is there a way to share connections via SSH and SOCKS5? I'd need to do this at a system-wide level though; I only know how to do it through the browser now. Then, I could run ifconfig eth0 192.168.4.1 on the computer sharing the inet, and ifconfig eth0 192.168.4.2 on the computer I'm trying to share with; I know this does work for host-to-host transfers. edit 3 If I run sudo killall dnsmasq, then nothing is using the 10.42.43.1 address the network manager sharing wants to use. But now it just takes longer to die, with error "NetworkManager[5935]: dnsmasq died with signal 9" [ http://pastebin.com/4FNtpugi ]. Looking at just the commands [ http://pastebin.com/1vrtQeWk ], maybe it's trying to route eth0 to itself? I'm not that familiar with networking things though.

  Read the article

• IPs on home network

  - by windchime

  I have a Linksys router and a Belkin wireless router at home. The Linksys router is connected to cable modem and two computers, as well as to the Belkin wireless router. A 3rd computer is connected to the Belkin router through Wifi. The IP addresses of the computers connected to Linksys are 192.168.1.101 and 192.168.1.102. The IP address of the Linksys router on LAN is 192.168.1.1. The IP address of the Belkin wireless router is 192.168.2.1(based on the 3rd computer's routing table) and the IP address of the 3rd computer is 192.168.2.5. If I ping 192.168.1.101 from 192.168.2.5, all are well. However, if I ping 192.168.2.5 from 192.168.1.101, Destination Host Unreachable. Why?

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• Unable to access internet if wireless enabled

  - by balki

  The following is my route output. eth0 is my wired network and eth1 is my wireless network. Only wired one has access to internet. If I enable wireless, I am not able to access internet, it tries to access via eth1 and I get 404 page of the wireless router. Why does eth1 have higher preference though default is eth0 (link)? [balakrishnan@mylap ~]$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.26.0.1 0.0.0.0 UG 0 0 0 eth0 10.26.0.0 * 255.255.192.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 * 255.255.255.0 U 9 0 0 eth1

  Read the article

• No wireless adapter in msi u200

  - by Mino Marimat

  I have a MSi u200, and the weird thing was that I was using this normally before, then after a few minutes all of a sudden it couldn't find the wifi signal from my house. I did some troubleshooting and a bit of search in the control panel, and it seems like my hardware is missing. :( I can't even turn on the wireless light using Fn+F8, so my suspicions about the missing hardware strengthened. I tried searching for DIY fixes, but I found out that the wireless card is actually built-in deeper, unlike the RAM cards and the hard drive where you can either replace or add more cards. What do I do?? As of the moment, I can get connected to my wifi here at home using a wireless adapter via usb, and it's working. So my guess about the hardware problem seems correct. HELP!!! Thanks!

  Read the article

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• Simple Java networking game engine [on hold]

  - by Florian Peschka

  I want to create a simple java networking game and search a networking engine that eases use of sockets etc. I have already read some questions on here and the internet about java networking for games, but many of them were over 10 years old or not really answered. I have no idea whatsoever about what exactly I need to send in terms of messages, but I figured simple strings or integers will be enough for my purposes. It's basically a peer to peer game, so I don't need a centralized server structure. Messaging doesn't have to have an extremely low ping, yet of course all players need to have a synchronized view. What are the possibilities I have here?

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >