Search Results

Search found 2774 results on 111 pages for 'adapter'.

Page 90/111 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

  • Ubuntu 12.04 - PPTP VPN is the only Internet Access

    - by user212553
    I know this has been covered. I've read dozens of posts but still have questions. I have a work server whose traffic should never leave my house without encryption. The VPN is PPTP. Currently I have a cron job that checks the status of the ppp0 adapter each minute. If the connection drops, which it does fairly often, it shuts key components down. It's fairly easy to restart PPTP with "nmcli con up id 'myVPNServer'" but there's no assurance it will reconnect and I need a better way to stop traffic (other than killing apps) when ppp0 is down. The two options I've seen discussed are the firewall (UFW, Firestarter, IPTables) or the route tables. I could be easily swayed to consider the firewall option but I focused on the route tables since no new function needs to be started. My questions involve the way the route tables change and then specifics on rules. When I start the PPTP VPN the route tables change. That suggests that if the VPN drops, the table will change back, defeating my stated intent of preventing external traffic. How can I make "sticky" changes to the route table that will persist even if the VPN connection drops? Perhaps the check boxes "Ignore automatically obtained routes" or "Use this connection only for resources on it's network" (which are part of the VPN configuration options)? It would seem that, if I can force the active VPN route table to stay in effect, even when the VPN drops, that this will effectively kill any external traffic should the VPN drop. This will give me the latitude to run a routine to restart the VPN from the command line (assuming the route table rules don't prevent me re-establishing the connection). My route table, with the VPN active is (ip route list): Any comments on what 10.10.1.1 is? $ ip route list default dev ppp0 proto static 10.10.1.1 dev ppp0 proto kernel scope link src 10.10.1.11 VPN_Server_IP_Address via 192.168.1.1 dev eth0 proto static VPN_Server_IP_Address via 192.168.1.1 dev eth0 src 192.168.1.60 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.60 metric 1

    Read the article

  • No Sound in 12.04 on Acer TimelineX 3830TG

    - by Fawkes5
    When i first installed ubuntu 12.04 everything worked fine. All of a sudden my sound has stopped working!! This has happened before [like 2 days ago], however the next day it started working again. That may happen again...[I've already rebooted 5 times] My Sound Card is a HDA intel PCH My Sound Chip is Intel CougarPoint HDMI My machine is an Acer TimelineX 3830TG, heres my lcpci output 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 540M] (rev ff) 02:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0) 03:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5116 PCI Express Card Reader (rev 01) 05:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) I'm running a dual boot with Windows 7, sound always works there. I've tried loading earlier kernels [3.2.0 ] but that hasn't helped. I've tried playing with alsamixer, unmuting and raising volume, doesn't work I've tried playing with pauvcontrol, doesnt work. Althought, strangely, when i play a song, under output i can see a bar moving implying that something is working, just the sound isn't getting through my speakers. Thus it might be a hardware problem. I've tried unistalling and reinstalling pulsaudio annd alsamixer, doesn't work [maybe made it worse...]. I've heard reverting back to kernel 3.0... works, but i'm reluctant to try that[i dont know much about kernels]. Thank you. Please tell me what other information you need. EDIT: My audio has started working again after another reboot. However this time im not connected to my external audio on startup. I will see if this is the issue next time i'm at home Edit: Connecting to external audio is not the problem.

    Read the article

  • What does "single-bit ECC errors were detected on the RAID controller" mean?

    - by jsp
    I have a Dell T7600 with a Perc H710P RAID controller and 4 attached 3TB drives. Over the past few months the RAID controller has been intermittently reporting errors on boot: "no boot device found", "adapter at baseport is not responding", disks frequently reported as missing or failed. I have since replaced the RAID controller, the 4 hard drives, and finally the system's motherboard. After replacing the motherboard and rebooting a few times, I got the error Single bit ECC errors were detected on the RAID controller. Please contact technical support to resolve this issue. After rebooting about 20 more times, I haven't seen the ECC error. The system seems otherwise OK, except for the fact that the disk fans will sometimes start blowing at full blast when the the system is sitting completely idle and not stop until I reboot. Are the ECC errors in memory on the RAID controller? Or, does the RAID controller map in system memory, and the ECC errors are really in system memory? Or, are the ECC errors in the 1GB cache that resides in the RAID controller?

    Read the article

  • RouterOS on Hyper-V (v3/2012) - any way to get it working?

    - by TomTom
    Trying to set up a small VPN point to connect into a remote Hyper-V cluster using ROuterOS. Anyone got it working ON Hyper-V with the latest builds of RouterOS? It seems the legacy network adapter is not supported anymore either (or just broken). The platform is a Windows Server 2012 RC. This is not a high performance setup - the RouterOS wont do the routing for more than the backend administrative access, and the only real traffic we will see there is when ISO images for new operating systems are uploaded. Otherwise we will have possibly RDP traffic as well as web / http traffioc, but this is internal only (dashboards, some control panel). The server has no public business. So the price for non virtualized network cards is ok for me. After hooking up - ping just does not work. After some time I see in windows (arp -a on the command line), so I know that the Hyper-V side is set up properly. Just no packets arrived. I have turned off all protection on Hyper-V (or : not turned them on), so no MAC spoofing protection etc. in the Advanced page for the legacy adapters. Unless I can get it work I will have to resort to using a windows install as router / VPN endpoint, which introduces another OS into the fabric (we run all routers etc. so far on mikrotik in hardware, which is why I want this one to be RouterOS, too). And no, putting hardware there is NOT an option - the cost would be significant.

    Read the article

  • Motherboard HDDPWR1 connector

    - by Eric Leschinski
    I need help identifying the name of a connector. I have a Gateway DX4870-UB318 computer, I opened the case and wanted to attach another hard drive, but to my surprise one existing SATA hard drive was connected to the motherboard with this connector: And here is the spot on the Motherboard where the power was supplied. What is the name of this adapter and where can I get another one? Clues: This computer was bought new October 2013 from best buy, box number: DX4870-UB318. The gateway folks won't divulge the type of motherboard it has nor give specs on it. On the wire itself is an identification code: H.35090NJ01-000 Next to the connector on the motherboard it says: HDDPWR1 and the second one says HDDPWR2. This cable has two SATA power connectors and one mystery connector. The power supply has no molex power cables and no SATA power connectors! This is the most bizarre hard drive power system I've seen. I guess the motherboard folks are trying to remove the burden for desktop power supplies to provide adapters (molex, SATA, other) to CD's and hard drives. Can someone put a name on that white flat 6 pin HDD Power Connector? My Solution I can buy a "SATA Power Y Splitter Cable" to provide more spaces to power sata devices.

    Read the article

  • Using Nortel Netdirect on Windows 7 64bit

    - by Matt Lewis
    Does anyone know how to use Nortel Netdirect (Version 7.1.3.0) with Windows 7 64 bit (Home Premium)? There are several ways available to me for connecting, all of which work for me on a 32-bit XP machine: Nortel Contivity VPN client (v6_02.022). The installer appears to be 16-bit, so I can't even install it on a 64-bit machine. Web-based SSL via IE Web-based SSL via Firefox The Web-based SSL process is supposed to load Netdirect and start it up, establishing the VPN connection. Using Firefox, I'm able to authenticate with my smartcard, but when it tries to download the applet, the process stops with a message box saying that it couldn't download the zip file. If I run Firefox in Vista compatibility mode, it gets a little farther, and manages to start Netdirect, but then exits after notifying me that the netdirect adapter was not installed. Using IE, I'm able to authenticate with my smartcard, then the java applet starts, but dies with the following sent to the java console: load: class NetDirect not found. java.lang.ClassNotFoundException: NetDirect at sun.plugin2.applet.Applet2ClassLoader.findClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) at java.lang.ClassLoader.loadClass(Unknown Source) at sun.plugin2.applet.Plugin2ClassLoader.loadCode(Unknown Source) at sun.plugin2.applet.Plugin2Manager.createApplet(Unknown Source) at sun.plugin2.applet.Plugin2Manager$AppletExecutionRunnable.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Caused by: javax.net.ssl.SSLHandshakeException: Received fatal alert: unknown_ca at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source) at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.recvAlert(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.startHandshake(Unknown Source) at com.sun.net.ssl.internal.ssl.SSLSocketImpl.startHandshake(Unknown Source) at sun.net.www.protocol.https.HttpsClient.afterConnect(Unknown Source) at sun.net.www.protocol.https.AbstractDelegateHttpsURLConnection.connect(Unknown Source) at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source) at java.net.HttpURLConnection.getResponseCode(Unknown Source) at sun.net.www.protocol.https.HttpsURLConnectionImpl.getResponseCode(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader.getBytes(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader.access$000(Unknown Source) at sun.plugin2.applet.Applet2ClassLoader$1.run(Unknown Source) at java.security.AccessController.doPrivileged(Native Method) ... 7 more Exception: java.lang.ClassNotFoundException: NetDirect I've tried installing certificates using java's keytool, but that didn't change the outcome.

    Read the article

  • Fetching e-mails into Redmine via IMAP

    - by Danilo Bargen
    I'm trying to fetch e-mails into Redmine via IMAP. The e-mails I'm generating look like this: FooBar Ltd 123456 http://example.com/Foobar-Ltd-123456.html Project: backend Tracker: Dataerror Beschreibung: This is the description =========================== CLIENT_IP: 192.168.1.215 HTTP_USER_AGENT: mozilla/asdfjköl I try to fetch them into Redmine via this command: rake -f /var/www/projects/redmine/Rakefile redmine:email:receive_imap \ RAILS_ENV="production" host=example.com port=993 ssl=true username=redmine \ password=1234 project=myproject tracker=other \ allow_override=project,tracker,category,priority \ move_on_success=read move_on_failure=failed But the e-mails get moved into the failed folder. I had this setup running some time ago with a different e-mail generator but pretty much the same template, and I can't figure out why it's not working. The permissions seem to be OK too. In order to further debug this issue, I need some logfiles. Are there any logfiles written by this command? Or are there any other suggestions to solve this issue? My environment: danilo@jabba:/var/www/projects/redmine$ RAILS_ENV=production script/about About your application's environment Ruby version 1.8.7 (i486-linux) RubyGems version 1.3.5 Rack version 1.0 Rails version 2.3.5 Active Record version 2.3.5 Active Resource version 2.3.5 Action Mailer version 2.3.5 Active Support version 2.3.5 Application root /var/www/projects/redmine Environment production Database adapter mysql Database schema version 20100819172912

    Read the article

  • DriveImage XML fails with a Windows Volume Shadow Service Error

    - by Ssvarc
    I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

    Read the article

  • Windows7 - “The specified network password is not correct.” when the password is in fact correct.

    - by Win7 Home User
    I have a samba server setup for some time now. It is a Hardware NAS - which unfortunately does not provide access to the Samba logs. (the exact model of the NAS is called Addonics NAS Adapter ) I also have a Windows Vista and a Windows XP machine - from both I am able to map \\192.168.0.20\Smd with no errors ( net use l: \\192.168.0.20\Smd works, after asking for my username and password). I also bought a brand new computer, with Windows 7, and when I try to execute the same exact net use command on it - using the exact same username/password pair, I get a "The specified network password is not correct." message. I also tried mapping from the Windows explorer menu, and got the same error. I synchronized the clocks of the two machines, tried again... and yet the same error persists. So what is really surprising here is that mapping works from WindowXP and Windows Vista machines, but fails from a Windows7 machine using the exact same command and username/password - Anyone has any idea of what could be causing this or how to solve the problem? Thanks

    Read the article

  • pGina with automatic Kerberos ticket and OpenAFS token/ticket

    - by rolands
    I am currently updating our educational Windows lab images from XP to 7, In doing so we are also migrating from Comtarsia to pGina. Unfortunately somewhere in the transition our automation that fetched kerberos and OpenAFS tickets/tokens on login has completely stopped functioning. Basically what used to happen was, using kfw-3.2.2 and the old OpenAFS release (loopback adapter days), either comtarsia would share password or something with the NIM (Network Identity Manager) which would authenticate against the kerberos server gaining a ticket and AFS token needed to access the users file, this was aided by the fact that our ldap database that windows authenticates against is also what kerberos uses to authenticate so usernames/passwords are the same across both services. I have set up all of the tools, albeit newer 64bit versions which seem to have given me less trouble than the previous releases of NIM/OpenAFS/Krb5, as well as setting their configurations back to what we used to use. Unfortunately this seems to be fubar'd in some way, instead all we get now is a OpenAFS token, most likely I assume from the AFScreds tool which operates some kind of integrated login process, although this does not help in getting a kerberos ticket or a afs ticket for which a login box is provided be NIM after the user logs in. Does anyone know IF it is possible to do what we are trying, and if so how? I was considering writing a pGina plugin which would interact with the server itself but this seems slightly like overkill considering that all these applications already exist...

    Read the article

  • USB To Serial under OpenSuse 11.3

    - by Lars
    I have a LogiLink USB-To-Serial adapter. This has the PL2303 chip inside. When I insert the device: [26064.927083] usb 7-1: new full speed USB device using uhci_hcd and address 9 [26065.076090] usb 7-1: New USB device found, idVendor=067b, idProduct=2303 [26065.076099] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [26065.076105] usb 7-1: Product: USB-Serial Controller [26065.076110] usb 7-1: Manufacturer: Prolific Technology Inc. [26065.079181] pl2303 7-1:1.0: pl2303 converter detected [26065.091296] usb 7-1: pl2303 converter now attached to ttyUSB0 So the device is recognized and the converter is attached to ttyUSB0. When I do screen /dev/ttyUSB0 9600 I get the error: bash: /dev/ttyUSB0: Permission denied So I went looking in the file permissions. ls -l from the /dev folder reports: crw-rw---- 1 root dialout 188, 0 2011-04-26 15:47 ttyUSB0 I added my user lars to the dialout group. When I use the commands groups under lars it shows that I'm in the group. Though I still recieve the permissions denied error, as lars, and as root. I'm trying to connect to a console cable to configure some Cisco switches. My OS is OpenSuse 11.3 x86_64 with kernel version 2.6.34.7-0.7-desktop.

    Read the article

  • How to securely enable file sharing over PPTP on Windows 2008 Server

    - by Damage
    I have set up a Windows SBS 2003 domain (LAN) and a stand-alone Windows 2008 Server (web server) at another location (workgroup). I established PPTP VPN connection (SBS dials web server) over which users from LAN should be able to access web server. On web server I enabled TCP/IPv4 and File and Printer sharing protocol. It has a few external addresses (one of them is default) AND one local address (192.x.x.x) assigned to network adapter. Firewall allows port 445 for file sharing. There's the problem - I can not enable web server file shares to be visible to LAN users and ONLY to LAN users: From SBS I can access webserver but I cannot access webserver from LAN workstations (XP, Vista). I have had same configuration - I have just replaced old (web server) Windows 2003 server with 2008 so SBS settings are the same (static route, DNS etc.). How can I enable file sharing on web server for LAN workstations? Now I have opened File and printer sharing to the internet which is of course totaly unsecure. I tried to secure the tunnel so I moved RAS (VPN) connection (Network Center) on web server to "Private" profile and moved firewall port 445 to "Private" profile but suddenly file sharing does not work and I cannot telnet webserver on port 445. How can I secure file sharing so I do not have to open it to the internet?

    Read the article

  • VMWare Server Windows 2008 NAT Problem

    - by David
    At my new job our workstations run Windows Server 2008. However, for the specific task for which I've been hired, I need to set up a couple Linux VMs. So I grabbed the free VMWare Server and created an Ubuntu image and a Slackware image. (The former to more closely mimic the production server, the latter because I'm more familiar with it.) For desktop security purposes I need to use NAT for the network access (I would have preferred bridged, but I'm told that would go against some policy here and my whole workstation would be sandboxed from the switch). However, I can't seem to get it working right. I can ping out from the VMs to LAN addresses as well as internet addresses. I can resolve DNS names. However, attempts to use a web browser or perform any kind of higher-level interaction like that just time out. Googling around yesterday led me to various workarounds that were similar, but didn't solve my specific situation. (For example, Norton firewall blocking the connection on the host, or even the Windows firewall.) I also saw some forum posts where people said it's a known issue with VMWare and Windows Server 2008 (and Windows 7). So far I haven't been able to find a suggestion that gets me past this roadblock. I'm really not very familiar with managing a Windows Server 2008 box, so it's possible there's just some security setting somewhere that I need to modify. Does anybody have any suggestions on where I should look? UPDATE: I'm now looking at the "Network and Sharing Center" on the host workstation and it shows "VMWare Network Adapter VMnet8" (which is what I'm using) as an "Unidentified network" with "No Internet access." Looks like I can't modify ICS under the group policy. Any suggestions on how to allow this connection to have internet access?

    Read the article

  • How can I use Linksys WPSM54G print server as a bridge for another machine AND also share the printe

    - by user26453
    I have a Linksys WPMS54G currently sharing a printer via the USB port with the rest of my network via the wireless. Is there any way to set it up so that the ethernet port is bridged over the wireless adapter portion? i.e., be able to uplink another machine or switch into the network via the WPMS54G's ethernet port? Update: The network architecture is as follows: (1) Linksys WRT54G router that serves as a router, DHCP server, and wireless access point for the network. Fairly standard configuration (3) Laptops that are used throughout the house via wifi (1) Linksys WPSM54G printer server that connects via wireless to the router, in a separate room with a printer attached to print seerver's USB port along with (1) Un-networked desktop in the same room Since the printer is plugged into the USB port of the WPSM54G, I am wondering if I can connect the desktop to the ethernet port of the WPSM54G and have it bridged over the wifi to the router. The twist here is that the ethernet is initially used to connect the wireless print server to the router (for configuration, can't configure it wirelessly if you are initially on a encrypted network). Now instead of using that ethernet port as a way to connect the print server to the network (via the router), I want to use the ethernet port as a way to connect another computer to the network, in effect bridging into the router via the print server, while still sharing the printer (attached via USB) through the print server. If this is not clear, please comment. To be clear, the computer I want to connect/bridge into the network does not have a wireless card, is far from the router, and I do not want to lay ethernet cable to connect it. While I could certainly buy a legitimate wireless bridge to accomplish this, I figured since the print server already has an ethernet port, see if I can't use that.

    Read the article

  • Debian and Multipath IO problem

    - by tearman
    Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

    Read the article

  • Drive XML returning Windows Volume Shadow Service Error

    - by Ssvarc
    I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

    Read the article

  • OpenVPN and TomatoVPN

    - by Bill Johnson
    Wondering if someone can help me with the following. I have updated my Linksys router with TomatoVPN and used the following config: Interface Type:TAP Protocol:UDP Port:1195 Firewall Custom Authorization Mode:Static Key I have then inserted the static key generated in OpenVPN saved and started the service. connect.ovpn. # Use the following to have your client computer send all traffic through your router # (remote gateway) remote (entered my DNS/DHCP servers external IP address here) port 1195 dev tap secret static.key.txt proto udp comp-lzo route-gateway 192.168.1.1 redirect-gateway float I've then placed my static key in a file in the same directory as your connect.ovpn (static.key.txt) Now OpenVPN is installed on a laptop that I use at home. I have plugged in the laptop to my home connection and started connect.ovpn The Local Area Connection is connected as 'Home Network 3' - and when I start OpenVPN it is connected as 'Local Area Connection 2' and this is showing as 'Unidentified Network' and it appears there is no network access. TAP-Win32 Adapter V9 appears to be the adaptors name and the IP and DNS properties are set to automatic. If I open up the OpenVPN GUI it shows an error message saying "Connecting to connect has failed". Looking at the error message behind this pop-up one line says "TCP/UDP Socket bind failed on local address [undef]:1195 Address already in use [WSAEADDRINUSE] Could anyone possibly help me further with this please?

    Read the article

  • My computer loses network connectivity every 30 minutes

    - by Logan Garland
    My LAN connected PC loses network connectivity every 30 minutes. It has a static IP address and I've checked to make sure there aren't any IP conflicts on my network. If I'm streaming from that PC to my Xbox the stream will be interrupted and it normally takes about a minute to come back online. The same happens if I'm actually on the PC and just browsing the web. I'm looking for suggestions on how to track down this issue. I've tried checking the available logs on my router to see if there is an issue with DCHP but have been unsuccessful in finding any evidence. Any suggestions would be helpful. I can't think of any recent changes to my network, PC or software installations that may have caused this. I am a software developer and have intermediate networking knowledge. EDIT: During one outage I told windows to troubleshoot the network problem and it said that it could automatically fix the problem by changing DCHP info. It basically said my network adapter from static to automatically obtain. This did fix the issue quicker than just waiting it out, but the outage occurred again 30 minutes later even when leaving those settings.

    Read the article

  • Windows Server 2008R2 - can't change or remove the default gateway

    - by disserman
    We've installed VMWare Server 2.0 on Windows 2008R2. After some time playing with it (actually only removing host-only and nat networks, and binding adapters to the specified vmnets) we've noticed a strange problem: if you change or remove the default gateway on the network card, the server completely loses a network connection you can't ping it from the subnet, it also can't connect to anyone. When the gateway is removed and a server tries to connect to the other machines, I can see some incoming packets using a sniffer, but I believe they are damaged in some kind (I'm not a mega-guru in TCP/IP and can't find a mistake in a binary translation of the packet) because the other side doesn't respond. What we tried: removed vmware server using add/remove programs deleted everything related to the vmware server and all installed network adapters in the windows registry double checked for the vmware bridged protocol driver file, it's physically absent and no any links in the registry. performed a tcp/ip reset with netsh and disabled/enabled all network adapters in the device manager to recreate a registry keys for them. tried another network adapter. and the situation is the same: as soon you remove or change the default gateway, windows stops working. The total absurd of the situation is that the default gateway points to the non-existing IP. But when it's set, you can ping a server from the subnet, when you remove it - you can't. Any help? I'm starting thinking the new build of the VMWare Server is some kind of the malware... :)

    Read the article

  • How to get decent WiFi despite a virtual Faraday cage

    - by MT_Head
    One of my clients is the local branch of an international airline. They have a small office in the secured area behind the ticket counters, and timeshare space at the ticket counter. I need to add a ticket printer out front, which I cannot (for contract/liability reasons) attach to the shared computer at the counter; the only workable solution seems to be to put the printer and its attached computer on a cart and connect to the office's network via WiFi. So far, no problem - right? Well, the terminal has been getting a facelift, which - among other things - includes decorative stainless-steel panels along the wall behind the ticket counters. This paneling acts as a seriously effective barrier to WiFi! The office's WiFi router - a brand-new D-Link DIR-815, dual-band 802.11n - is just on the other side of the pictured wall, and twenty feet or so to the right. And yet the only way I can connect AT ALL on this side of the wall is to stick the USB adapter (on the end of an extension cable) right into the crack between panels... and even then I can only see the 5GHz network, and that very weakly. Has anyone else had experience with this sort of misguided interior decoration? Any ideas on how I can improve reception on the other side of the barrier? (Needless to say, physical modifications of the environment - tempting though they might be - are strictly no-go.)

    Read the article

  • Windows 8 unable to connect to WPA2 AES Wireless Network

    - by user170193
    I'm running Windows 8 and am unable to connect to my home wireless network. I've tried restarting the router, patching the drivers to the next version, patching the drivers to the last version, running windows update and patching the chipset drivers to the latest version. So far nothing has worked. My computer can get on the internet via USB tethering on my phone or an open WiFi connection, but it is unable to connect to my home WPA2 AES secured wireless network. It sees the network, attempts to connect, gets a limited connection and then drops the connection. All the other wireless devices in my household have no problems. I have the new Dell XPS 12, running Windows 8 using an Intel Centrino Advanced-N 6235 wireless adapter. I've refreshed windows twice now to try different driver configurations. I've tried uninstalling all the Dell software, I've tried uninstalling all the Intel software and reinstalling just the drivers. I've tried turning switching the ability for the Wireless driver to turn the computer off or on. I've tried setting up the connection manually from desktop mode. I've tried switching it on and off using the wireless button on the keyboard and in the software. So far nothing has allowed me to connect to the secured network. It just keeps getting a limited connection, dropping the connection and retrying. It's driving me crazy, any ideas, anything I missed? Thanks.

    Read the article

  • Dell 15Z. Trying to output image using Mini Displayport to a Yamasaki Q270. (2560 x 1440) rez monitor. Dual DVI-D to Mini Displayport

    - by michaelcku
    I have a Dell 15Z. GT525M Video card. Updated Driver via NVIDIA. Problem is I just purchased a Yamasaki Catleap Q270 monitor. It is a (2560x1440) monitor with only a Dual DVI-D out. 15Z only has HDMI and a Mini Display Port. I got a Active Dual DVI-D to Mini Display Port Active Adapter(Linked Below). http://www.monoprice.com/products/product.asp?c_id=104&cp_id=10428&cs_id=1042802&p_id=6904&seq=1&format=2 The Setup works when i plug it into my Macbook air 13.3. However when I plug it into my 15Z it doesn't work. Tried everything I can thank of. Window control P. FN and F1. It just doesn't work. I believe the issue lies in the Mini Display Port but i can't be sure. No matter what i do, the Mini Display Port doesn't get recognized. Spent 3 hours on the phone with the XPS Tech team. They simply said it was not compatible.... Any help or suggestion would be greatly appreciated.

    Read the article

  • Can a wifi AP act as a client, and a server at the same time?

    - by nbolton
    I feel this is SF worthy (as opposed to SU) as I go into a bit of detail on gateways/routing. Here's my ideal setup (if possible) -- there is a wifi network (lets call it bob's) with which I want access to, but I have a few other computers on my network which I want to keep behind a firewall. So I was thinking of buying a wireless access point so that I could set it up to connect to bob's network from the AP, and then from my server, connect to the AP via ethernet. So that's the first bit. Second part is that I want to have my own private wifi network off the back of this; can I then tell the AP to serve a new network called foobar. When I say private network, I mean that my server is actually a Debian linux install with routing configured (and I also do some QoS stuff on, etc). So ideally, I'd like all the clients on the private network to be behind the server in terms of routing. However, if the private clients connect to the server via wifi, then aren't they exposed to the "public" network? That is, if someone is savvy enough to scan for my IP range. Also, to do routing I'd need to connect two ethernet cables between the server and the AP (because you can't do routing/QoS on virtual devices) -- which isn't a problem really; but I'm not sure whether the AP will allow me to separate the public and private LANs. Or, as well as the AP, am I better getting a wifi-to-ethernet adapter for the server? I could use a wifi usb, but this can be tricky to set up on headless linux; plus the signal strength is a bit lousy. If this question is a bit vague/spurious in places, please comment and I will explain in more detail.

    Read the article

  • Vista ICS issue

    - by Bill Grey
    I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

    Read the article

  • Server 2003, XP Clients, DNS issues

    - by ron
    Hello, Im having DNS issues on my network. My DC is my DNS server 10.76.4.11 and recently I configured a forwarder to 10.4.36.10. My workstations are not working because they cannot resolve the domain controller name because of DNS. an ipconfig /all reveals that they know the IP of the DNS server is 10.76.4.11, but if I nslookup 10.76.4.11 it forwards the request to 10.4.36.10 and goes nowhere. I have since removed the forwarder, but still any nslookup requests on workstations are going to 10.4.36.10. If I nslookup 10.76.4.11 on the server it can resolve its name, but for some reason when it receives the same request from workstations it doesnt know what to do. All the A, CNAME records etc are correct. DHCP's DNS is set correctly, GPOs are correct (even though they cant refresh cos of this problem!), the servers network adapter has its DNS set to 10.76.4.11. Just don't know. Very confused.

    Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >