Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 90/761 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

  • "Safe" personal router use on apartment-wide network

    - by noisetank
    I recently moved into an apartment with internet included in my rent. This was a boon at first, but now I'm feeling limited. To get devices connected (wired or wireless), I have to whitelist the MAC addresses on mycampusnet.com. This is annoying (considering I'm well over the 10 device limit including my roommate's stuff), but what's really driving me mad is that I don't seem to have any semblance of a "local" network. I've relied heavily on static IPs and port forwarding in the past (accessing NAS and remote desktop) and (as far as I can understand), that functionality is nonexistent without my router set up. Also, as my wired and wireless devices don't always seem to make it onto the same subnet, I'm unable to use any of my iDevices with my Apple TV (I can, however, mirror to no less than four strangers' Apple TVs at any moment, which is a whole other level of discomforting). I've talked to the head of the apartment complex and she told me that they personally don't have any issue with my using a router, but the provider (CampusConnect) does not currently allow it. Apparently, enough people have put in complaints/requests about the restriction (the apartments are for graduate students and University staff, many of which need to set up things like VPNs for work reasons) to open up some sort of ticket to get the functionality in place, but all the calls I've made to get status updates have been a waste of time. My question is: If I plugged my router into the apartment network, what would happen? I've been told already that personal routers would "interfere with the wireless" and that they would shut my port down if I used one, but is that a legitimate thing or just something made up that sounds real to keep the average Joe from pushing it further? I'm guessing there's some way of configuring my router to keep it from disrupting the rest of the network, but it's not something they want to tell me for obvious reasons. Am I right? And if so, what are the chances that they'd notice the difference in traffic or whatever and shut off my port?

    Read the article

  • Arch Linux drops me on my school network

    - by Kravlin
    I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

    Read the article

  • dns in a small network with router and AD domain

    - by Felix
    I have a small office network with router (running OpenWRT), Windows Domain Controller (used to be 2008R2; I just backed it up and upgraded to 2012), about a dozen AD clients (3 server and windows workstation) and several non-AD clients (network printer, PBX). The problem is that the clients can't access servers by name (only by IP). I tried all kind of permutations. Right now domain controller runs DNS server for all desktops; but unless I put an entry in hosts file - I can only get by IP. I have router as DHCP server (since not all devices are on AD); and except for Domain Controller all IP addresses, including "static", are assigned by the router. Most frustrating, some servers sometimes just work! for example, I can often get to the Linux box by name (it is part of Domain using Beyond Trust Integration Services); but I can never get to SQL Server box. Seems like non-domain devices see more names than domain members... This network should be fairly typical; but I couldn't get any guidance about how to set up DNS/DHCP service to make all nodes happy. The closest is this question, but still it's different! Thanks

    Read the article

  • Loosing network cached passwords after a restart on Vista

    - by Nauman
    The passwords cached for Network shares on other computers and applications like MSN Live, MS Outlook, Sharepoint portal, Outlook Webmail, etc are lost when I reboot my computer, which runs on Vista. I always check the Remember password checkbox in applications/login dialogs where ever prompted. I cannot imagine of a third party program that may clean up this on system restart/shutdown. Any idea, as to what is going wrong?

    Read the article

  • How to serve media across home network?

    - by TK Kocheran
    I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

    Read the article

  • How do you hide a computer name on a network? (OS X 10.6)

    - by George
    I regularly plug my Macbook Pro into a network at work, but because of the way Mac networking works, my computer's name instantly becomes available to any other Mac on the network. Is there a way to hide my computer's name so that I do not appear on the network list of other people's computers? Also, can I set this up so as a network specific profile? For instance, I would like my computer's name to show up on my home network, but not my work network.

    Read the article

  • Copy UNC network path (not drive letter) for paths on mapped drives from Windows Explorer

    - by Ernest Mueller
    I frequently want to share network paths to files with other folks on my team via email or chat. We have a lot of mapped drives here, both ones we set up ourselves and ones set up by our IT overlords. What I'd like to be able to do is to copy the full real path (not the drive letter) from Windows Explorer to send to folks. Example: I have a file in my "Q:" drive, \cartman\users\emueller, I want to send a link to file foo.doc to everyone. When I copy the file path (shift+right click, "copy as path") it gets the file name "Q:\foo.doc". This is unhelpful to others, who would like to see \cartman\users\emueller\foo.doc, obviously. In Explorer it clearly knows it - in the address bar I see "Computer - emueller (\cartman\users) (Q:) -". Is there a way to say "hey man copy that path as text with the \cartman\users\emueller not the Q: in it?" I know I could just set up mapped network locations instead of the mapped drives for the ones that I set up personally and avoid this problem, but most of the mapped drives like the "users" share come from our IT policy. I could just make a separate network location and then ignore my Q: drive but that's inconvenient (and they do it so they can move accounts across servers). Sure my emailed path might eventually break because I'm losing the drive letter indirection but that's OK with me.

    Read the article

  • Cannot Access Shared Folder From IIS

    - by Tim Scott
    From IIS I need to access a folder on another computer. Both servers are Window 2008 SP2, and they live in a Virtual Private Cloud on Amazon EC2. They reach one another by private IP -- they are in WORKGROUP, not a domain. I can access the shared folder manually when logged in to the client as Administrator. But IIS gets "access denied." Here's what I have done: Set File Sharing = ON Set Password Protected Sharing = OFF Set Public Folder Sharing = ON Shared the folder Added permission to the share: Everyone, Full Control Added permission to the share: NETWORK SERVICE, Full Control Verified that File & Printer Sharing is checked in Windows Firewall Opened port 445 to inbound traffic from local sources I tried adding <remote-machine-name>\NETWORK SERVICE to the share but it says it does not recognize the machine, which makes sense, I guess. As I said, from the other computer I have no trouble accessing the shared folder from my user account, but IIS is shut out. How does the file server even know the difference? I would assume that with Everyone given full control and password protected sharing turned off, it would not matter what the client user account is. In any case, how to solve? UPDATE: To clarify, I am not trying to serve up files on the share directly through IIS. Rather I am writing files to the share from my code (System.IO).

    Read the article

  • Unable to access network resources through VPN

    - by fbueckert
    I'm currently attempting to connect one of our computers in the office to a client VPN. My development machine is running Windows 7, and can connect and see resources just fine. The problem computer is running Windows XP. They're both within the same network. Using the same credentials at both computers, the VPN connection (using the built in Windows network connections) works just fine. So far, so good. An IP address is assigned, and comparing both machines shows they're still in the same subnet. The problem is that the XP machine cannot see ANY of the computers in the client network. I tried a tracert to a target machine on the Windows 7 box, and the first item that comes up is the .0 address. Pinging it gives responses. Trying it on the Windows XP machine, however, comes up with just timeouts. Trying to trace to www.google.com allows the address to resolve (probably part of the cached resolutions), but results in just timeouts. I double-checked to make sure that the Windows firewall was not on, and trying to open the settings brings up a notification that the firewall service wasn't running, which leads me to believe that it's definitely not on. From my best guess, I've managed to connect the XP machine to a black hole of some sort. There's obviously something strange going on, but I'm not sure where I should be looking.

    Read the article

  • outlook security alert after adding a second wireless access point to the network

    - by Mark
    Just added a Netgear WG103 Wireless Access Point in our conference room to allow visitors to access the internet through out internal network. When switched on visitors can connect to the intenet and everything works fine. Except, when the Access Point is switched on, normal users of the network get a Security Alert when they try to start Outlook 2007. The Security Alert is the same as the one shown in question 148526 asked by desiny back in June 2010 (http://serverfault.com/questions/148526/outlook-security-alert-following-exchange-2007-upgrade-to-sp2) rather than "autodiscover.ad.unc.edu" my security alert references our "Remote.server.org.uk". If I view the certificate it relates to "Netgear HTTPS:....", but the only Netgear equipment we have is the new Access Point installed in the conference room. If the Access Point is not switched on we do not get the Security Alert. At first I thought it was because we had selected "WPA-PSK & WPA2-PSK" Network Authentication Type but it continues to occur even if we opt for "Shared Key" WEP Data Encryption. I do not understand why adding a Netgear Wireless Access point would cause Outlook to issue a Security Alert when users try to read their email. Does anyone know what I have to do to get rid of the Security Alert? Thanks in advance for reading this and helping me out.

    Read the article

  • Copy UNC network path (not drive letter) for paths on mapped drives from Windows Explorer

    - by Ernest Mueller
    I frequently want to share network paths to files with other folks on my team via email or chat. We have a lot of mapped drives here, both ones we set up ourselves and ones set up by our IT overlords. What I'd like to be able to do is to copy the full real path (not the drive letter) from Windows Explorer to send to folks. Example: I have a file in my "Q:" drive, \\cartman\users\emueller, and I want to send a link to the file foo.doc therein to coworkers. When I copy the file path (shift+right click, "copy as path") it gets the file name "Q:\foo.doc". This is unhelpful to others, who would need to see \\cartman\users\emueller\foo.doc to be able to consume the link. In Explorer it clearly knows it - in the address bar I see "Computer - emueller (\\cartman\users) (Q:) -". Is there a way to say "hey man copy that path as text with the \\cartman\users\emueller not the Q: in it?" I know I could just set up mapped network locations instead of the mapped drives for the ones that I set up personally and avoid this problem, but most of the mapped drives like the "users" share come from our IT policy. I could just make a separate network location and then ignore my Q: drive but that's inconvenient (and they do it so they can move accounts across servers). Sure my emailed path might eventually break because I'm losing the drive letter indirection but that's OK with me.

    Read the article

  • Windows 7 comments field missing when browsing network

    - by Toymangenie
    I have just purchased three Windows 7 Professional Dell 64-bit PCs for testing prior to upgrading our company’s 120+ PCs from Windows XP Professional. The setup is a standard domain with a Windows Server 2003 32-bit server. We name each PC XP1 to XP150 so that when users join or leave, I don’t have to rename the PC. We use the Description field to allocate the user’s name to each PC. We also have a share set up on each PC using the user’s name. When I browse the network using Windows Explorer in XP, I get a useful display. The left pane showing the PC number and the right pane showing NAME and COMMENTS So, for example I would see: XP01 Fred Bloggs (Each PC on a new row.) The right pane is my main tool for administering the network. I can easily see the PC number and the name of the user. However, in Windows 7, this seems to have been thrown out of the window and replaced with fields that I do not need and in my case always display the same info. "Name", "Category", "Workgroup", "Network Location" In my case the Name column gives the PC number (XP10) etc and all three other columns display identical useless information. So I can’t see who is using XP10. When I am in “help desk” mode, I would naturally ask the user’s name and use my remote desktop client to view their screen. The user isn’t aware of their PC name, so I am finding it impossible to match the user name with a PC number. Any ideas how to overcome this "by design" change to Windows 7?

    Read the article

  • Setting up a network where packets are traced

    - by Marcus
    My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

    Read the article

  • VLAN for WiFi traffic separation (new to VLANing)

    - by Philip
    I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

    Read the article

  • Find slow network nodes between two data centers

    - by 2called-chaos
    I've got a problem with syncing big amount of data between two data centers. Both machines have got a gigabit connection and are not fully occupied but the fastest that I am able to get is something between 6 and 10 Mbit = not acceptable! Yesterday I made some traceroute which indicates huge load on a LEVEL3 router but the problem exists for weeks now and the high response time is gone (20ms instead of 300ms). How can I trace this to find the actual slow node? Thought about a traceroute with bigger packages but will this work? In addition this problem might not be related to one of our servers as there are much higher transmission rates to other servers or clients. Actually office = server is faster than server <= server! Any idea is appreciated ;) Update We actually use rsync over ssh to copy the files. As encryption tends to have more bottlenecks I tried a HTTP request but unfortunately it is just as slow. We have a SLA with one of the data centers. They said they already tried to change the routing because they say this is related to a cheap network where the traffic gets routed through. It is true that it will route through a "cheapnet" but only the other way around. Our direction goes through LEVEL3 and the other way goes through lambdanet (which they said is not a good network). If I got it right (I'm a network intermediate) they simulated a longer path to force routing through LEVEL3 and they announce LEVEL3 in the AS path. I basically want to know if they're right or they're just trying to abdicate their responsibility. The thing is that the problem exists in both directions (while different routes), so I think it is in the responsibility of our hoster. And honestly, I don't believe that there is a DC2DC connection which only can handle 600kb/s - 1,5 MB/s for weeks! The question is how to detect WHERE this bottleneck is

    Read the article

  • Small office network setups

    - by user39822
    I work at a small office and we're overhauling our network setup there. We're a web dev company and at the moment we have 50+ production sites running on the same machine that runs our internal email, which is just plain stupid. We're moving all our client hosting off site and are now looking for something to run our internal office requirement. Below is a brain dump: Equal amount of Mac & PC, about 25 machines in total. We need a central "server" to host files that should be accessible everyone as a "network drive". If possible we'd like to use low cost hardware for this (Mac or Win based). Disk space should be upward of 1TB. Ideally we should also be able to run a small web server on this machine (LAMP stack) to run some planning and billing applications we wrote ourselves. We need some sort of MS Exchange alternative for things like a shared calendar and especially being able to set Out of Office replies. We have one printer that is connected to the network Setup should be something can preferably be managed easily via a graphical interface and NOT require command line skills. Users want to keep using Apple Mail or MS Outlook After a quick google I came across the Zimbra collaboration suite, can anyone recommend this or any other solution for our office?

    Read the article

  • Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

    - by WerkkreW
    I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

    Read the article

  • Photo managing software that supports network drives?

    - by musicfreak
    My dad is a photographer in his free time, and he's been using Lightroom to manage his photos. However, recently, we put all of our photos on a NAS drive to allow us to access them from any computer at any time. The problem with this is that Lightroom cannot load catalogs from network drives. We need support for network drives because we'd like to be able to browse the photos from any computer, and for any computer to be able to add photos to the collection. Right now we're just syncing the Lightroom catalog file between us, but the extra step is a pain, and doing it manually makes it error-prone. Is there any software (free or commercial) that has proper support for network drives? The only real feature I need is to be able to sort photos by date and by some sort of tags. I don't need any editing features like those found in Lightroom; my dad is comfortable using Photoshop to edit photos. Also, if there is another solution to this that I haven't thought of, feel free to share.

    Read the article

  • Pages load in brower fine, but 404 not found reported for the page during the GET on all pages except index

    - by user885983
    I believe this question is more suited to serverfault (please correct me if not). This issue appears very similar to this question (except there are no 301 Moved Permanently for any pages). The domain is yorkshirebadges.co.uk. For example, loading yorkshirebadges.co.uk or yorkshirebadges.co.uk/index.php reports no 404s during network inspection. But every other page (/contact.php, /products.php) report a not found. Mod_rewrite is being used on the site, I checked this out but didn't see any obvious errors. It's included below for reference: RewriteEngine on RewriteRule ^store/material/([^/\.]+)/price/?([^/\.]+)?$ products.php?prodType=$1&price=$2 RewriteRule ^store/price/?([^/\.]+)?$ products.php?price=$1; RewriteRule ^store/material/?([^/\.]+)?$ products.php?prodType=$1 RewriteRule ^store/([^/\.]+)/?$ products.php?prodCat=$1 RewriteRule ^store/([^/\.]+)/price/([^/\.]+)$ products.php?prodCat=$1&price=$2 RewriteRule ^store/Type/?([^/\.]+) products.php?prodType=$1 RewriteRule ^store/([^/\.]+)/?([^/\.]+)?$ view-product-details.php?cat=$1&prodName=$2 RewriteRule ^store/([^/\.]+)/material/?([^/\.]+)?$ products.php?prodCat=$1&prodType=$2 RewriteRule analytics http://www.google.com/analytics <IfModule mod_suphp.c> suPHP_ConfigPath /home/yorkshir <Files php.ini> order allow,deny deny from all </Files> </IfModule> Chrome Network Inspection (and firebug on firefox) report 404s on all pages except the index, the server is apache2. Really scratching my head on this one!

    Read the article

  • Failure to connect to admin share pops up dialog

    - by Jan
    I'm having an issue with a curious error message when accessing the administrative share on a remote machine. Specifically, the client is logged in as the domain administrator on the machine A, and runs some code that tries to access the admin share on B (a domain member). The access is done in .NET, along these lines (though I am not sure if the method of access makes a difference): string path = @"\\B\admin$"; if (Directory.Exists(path)) { try { path += @"\temp\"; if (!Directory.Exists(path)) { Directory.CreateDirectory(path); } path += "myfile_remote"; File.Copy("myfile", path); Now, on some machines this fails. That is not a big problem as we have a fallback. I'd like to know why but it is not the real issue. The problem is that running this piece of code causes a dialog box to pop up for the logged-in user on B, saying "network error trying to access \\B\admin$\temp\myfile_remote. Contact the network administrator and ask for the correct permissions". Unfortunately, it is a foreign language Windows so I'll spare you all posting a screenshot. It is skinned like a standard Windows dialog box. Why exactly is that dialog box popping up for the user and is there anything I can do about it? Edit to add: B is a Windows 7 Enterprise installation. The client is not aware of any GPO policies being installed. There is AV from Trend Micro installed.

    Read the article

  • Salary Survey Entry Level network position [closed]

    - by will
    Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

    Read the article

  • How can I monitor VNC via Nagios?

    - by atroon
    I have a number of remote sites which have VNC running on a few computers for support purposes. They are (obviously) only available on our internal network. I am using Nagios to keep track of all the systems in the network and I want to have it check to make sure the VNC server is running on the appropriate hosts. There is a 'check_vnc' plugin available here but it relies on VNC Snapshot which I don't want to use. Certainly I could use it, but it adds more complexity and dependency, which I want to avoid. It seems simpler to just use check_tcp to make sure I get the proper response to a connection request for VNC, e.g. port 5900, send a connect string, get back framebuffer info. My real question, I suppose, is this: What is the 'proper' generic connect string for VNC (I use both UltraVNC and RealVNC) and what is the expected response? If it's really easier to use the VNC Snapshot and check_vnc, let me know. I just can't imagine that a string of text isn't easier, faster, and less bandwidth intensive to monitor.

    Read the article

  • Choosing gateway router/firewall for small datacenter network [closed]

    - by rvs
    I'm choosing a gateway router/firewall for small internal network for medium-sized web service. Currently there are 5 servers in internal network, up to 50 http(s) requests/second, up to 1000 simultaneous connections, uplink is 100 Mbit. So, network is relatively small and not very busy and we don't like to buy some pricey monster like cisco or jupiper for this site. Instead we'd like to buy two affordable devices (one for spare), which can handle our workload now and some time in future (it might be up to 2x more in 1 year). I had some experience with Sonicwall NSA, but it seems to be too complex for this site (we don't need most of its features) and even too pricey when buying two of them. So, after some research I've come up with following options: Netgear Prosecure UTM Series (probably UTM25) Zyxel ZyWall Series (USG100 or USG200) Sonicwall TZ 210 Is this a good idea? All of the above seems to be more office products, not datacenter ones. Or we should stick with Sonicwall NSA? Does anyone have any hands-on experience with this models? Maybe some other advices? Thanks.

    Read the article

  • Raspberry pi slows down my entire network

    - by gnusouth
    Whenever my Raspberry Pi is connected to the network (via ethernet) the entire network is slowed to a crawl. On my main computer, ping times for google.com go from ~10ms to ~200ms and it takes forever to load web pages. Connections are also slow on the Pi, with an apt-get update showing pathetic speeds in the order of 1KB/s. Turning off the Pi completely removes the drag from the network. I've tried static and dynamic IP addresses for the Pi, but both have the same problems. I'm currently using Raspbian (downloaded today), but also had this problem with Arch Linux. I've checked the connection's duplex with dmesg | grep -i duplex, which shows that the Pi's connection is running at 100Mbps, full-duplex, as expected. My modem/router is a Billion 7404VNPX (an Australian thing); relatively high-end, albeit a bit buggy at times (it will occassionally delete all its firewall settings). It assigns IPs in the range 192.168.1.1 to 192.168.1.20 and has 192.168.1.254 as its own IP. When I assign static IPs I tend to use the 192.168.1.200 area. Does anyone have any idea as to what could be causing this weird slowdown? Or any tests I could try? Thanks

    Read the article

  • Remote network traffic not passing through VPN

    - by John Virgolino
    We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

    Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >