Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 91/761 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• PHP application failed to connect after a network plugged back in

  - by tntu

  My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

  Read the article

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• pfSense routing between two routers with shared network

  - by JohnCC

  I have a network set-up using two pfSense routers arranged like this:- DMZ1 WAN1 WAN2 DMZ2 | | | | | | | | \___ PF1 PF2___/ | | | | \___TRUSTED___/ Each pfSense router has its own separate WAN connection, and a separate DMZ network attached to it. They share a common TRUSTED LAN between them. The machines on the trusted network have PF1 as their default gateway. PF1 has a static route defined to DMZ2 via PF2, and PF2 has a static route to DMZ1 via PF1. There is NAT to the WAN but internal networks (DMZ1/2 and TRUSTED) use different RFC1918 subnets. I inherited this arrangement, and all used to work fine. I made a config change to PF1 (relating to multicast), and machines on DMZ2 suddenly could not talk to TRUSTED. I rolled the change back, but the problem persisted. What I guess you'd hope would happen is that TCP packets would go DMZ2 - PF2 - TRUSTED and on return TRUSTED - PF1 - PF2 - DMZ2. That's the only way I can see it would have worked. However, PF1 drops the returning packets. I've verified this using tcpdump. I've worked around this by adding static routes to DMZ2 via PF2 to the servers on TRUSTED, but some devices on there do not support static routes so this is not ideal. Is there way to make this arrangement work decently, or is the design inherently flawed? Thanks!

  Read the article

• Windows 7 'Unidentified Network'

  - by Throdne

  So my internet was working last night before I went to bed and woke up to a computer that is showing unidentified network. I have tried multiple ways of fixing it. > route delete 0.0.0.0 > uninstalling drivers - restart - reinstall from downloaded drivers > ipconfig /release - /renew > static IP > speed & duplex from auto negotiation to 1.0gbps full duplex > and also changed my network address to no value to 1234567890ab (not in that order) nothing seems to work. I have Comcast internet and when I connect the computer to the modem it works perfectly. but when I connect it to my router again, Unidentified network. I know my router isn't faulty, because my macbook pro, server, NAS, iPhones, and iPads are still working. I have also tried moving the port on the router, still same problem. my router is a: Cisco Small Business RVS4000 motherboard: GIGABYTE GA-990FXA-UD3

  Read the article

• Strange WiFi problem - network is "not connected" but works

  - by GalacticCowboy

  Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

  Read the article

• Windows mounted network drives slow after upgrading switch

  - by Kver

  On our small business network our old 10/100 consumer grade switch gave up the ghost, and we replaced it with a proper business-grade gigabyte switch. After wiring it in our Linux and Mac users immediately got back to working off of network drives; But 2 of our 3 Windows 7 PCs have suddenly experienced a tremendous slowdown with mapped network drives; Windows will become stuck "discovering" a folder causing applications to freeze when trying to open files. It will instantly display and browse files, but the moment you try to open one the bug hits. To remedy this we have our users copying files to the desktop, but it can take a few minutes while windows is stuck "calculating" the time it will take to copy. These aren't big files, mostly excel sheets less than 500KB - these operations are instant on Linux and Mac. (The third Windows machine is having no issues) I've tried remapping the drives, mapping to different drive letters, rebooting, etc. I'm at a loss, because switches are mostly transparent, and it's only after the switch was replaced that the Windows PCs started acting up. What black-magic voodoo am I missing to make Windows work? Thank you.

  Read the article

• Service redirection on same network

  - by Unode

  I have a network on which I run multiple servers each dedicated to a given service. Because most services run on distinct ports I'm currently looking for a way of unifying "all" services into a single "proxy" machine. The idea is to abstract which machine is being accessed but still allow direct connection if needed/requested. This "proxy" machine has only one network interface which is part of the same network as all the other service providing machines. I've looked into Routing and NAT but I've so far failed to figure out how to make it work. I tried to achieve this using shorewall but couldn't find clear examples. However I'm not entirely sure this is the best/simplest strategy. With that said, what would be the best way of achieving this result? Example case: Proxy IP - Listening port - Send requests to 192.168.0.50 80 192.168.0.1:80 " 22 192.168.0.2:2222 " 3306 192.168.0.3:3000 " 5432 192.168.0.4:5432 " 5222 192.168.0.5:5222 PS: I'm not concerned with the single-point-of-failure nature of the proxy. Thanks

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• how to build network across buildings ?

  - by Omie

  Hi ! I need some help in building a network between hundreds of computers spread across multiple buildings of my college. Yes, I'll be doing this as a part of my college project. Please see this image, it will give you enough idea of what I'm trying to achieve. http://i.imgur.com/rOohx.png All the computers in all buildings should be able to connect server. Once network is up, there will be a set of services over intranet and network use will be moderate. well, say there will be an email server and a http server. My point is, I cannot afford much of performance loss. It feels easy to connect computers inside 1 building to each other, however, I'm clueless as to how to connect all of them to server. I mean, just 1 cable won't be enough to connect 1 building to server, right ? How should I go with it ? I am not expecting detailed configuration. Just heads up will do :) Thanks

  Read the article

• VirtualBox bridged network not working as expected

  - by iby chenko

  I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

  Read the article

• Protocol (or service publish/discovery) to detect devices in network

  - by Gobliins

  we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

  Read the article

• Can't access apache from outsite my local network

  - by valter

  UPDATED: Now, when I type my external ip like xxx.xxx.xxx.xxx:8079, i can access xampp defaults page. But the strange is that when someone else from outside my network, try to access it using the same ip, it doesnt work. I Think it should, because its the external ip. I'm getting crazy. I have tried for hours to access xampp defaults page from outside my local network. My ISP blocks port 80 and 8080. So I changed apache to listen to port 8079 Listen 8079 My local computer ip is 10.1.1.2 I can access the webserver, from any computer on my local network when I type http://10.1.1.2:8079 I also oppended the port 8079 on my modem, as the image shows bellow. (I think i did it right) When apache is running on my computer, if I test the port 8079 at http://canyouseeme.org/ i get the message "Success: I can see your service on xxx.xxx.xxx.xxx on port (8079) Your ISP is not blocking port 8079" If apache is not running I get "Error: I could not see your service on xxx.xxx.xxx.xxx on port (8079) Reason: Connection refused". So, it's clear that the port 8079 is oppened. But when I type xxx.xxx.xxx.xxx:8079 on google chrome for example, I get Oops! Google Chrome could not connect to xxx.xxx.xxx.xxx:8079 What can I do to solve this, to allow apache to server the pages? I don't know what else I shoud configure. Please, help me. Thanks.

  Read the article

• Computers on network crashing

  - by Phil Cross

  We have recently upgraded our network to Windows 7 clients with Windows server 2008 servers. The upgrade was completed by the end of September and until now has been fine (apart from the minor bugs). Recently (within the last 2 weeks) we've notice all computers on the network (around 1000) start to slow down to the point their unusable. It starts at about 08:45 and finishes at 09:15. Because of this, we think something may be broadcasting across the network. This happens every day, between these times. I cant use my computer at all at the slowdown peak, and looking at task managers performance graphs, Physical memory is hovering around 35% and CPU usage is at 0-10% (idle) yet still crashing. I've looked on DHCPs server log and cant see anything which stands out. The only change we made prior to the slowdown was installing adobe CS6 on some computers, however the slowdown affects computers without CS6. We have 2 physical machines, each with around 5-7 virtual machines running on them with ample memory. Does anyone have any suggestions as to what we can do to narrow down whats causing the crashes? Any help, suggestions or advice would be appreciated.

  Read the article

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• Postfix/SMTPD Relay Access Denied when sending outside the network

  - by David

  I asked a very similar question some 4 or 5 months ago, but haven't tracked down a suitable answer. I decided to post a new question so that I can ... a) Post updated info b) post my most current postconf -n output When a user sends mail from inside the network (via webmail) to email addresses both inside and outside the network, the email is delivered. When a user with an email account on the system sends mail from outside the network, using the server as the relay, to addresses inside the network, the email is delivered. But [sometimes] when a user connects via SMTPD to send email to an external address, a Relay Access Denied error is returned: Feb 25 19:33:49 myers postfix/smtpd[8044]: NOQUEUE: reject: RCPT from host-68-169-158-182.WISOLT2.epbfi.com[68.169.158.182]: 554 5.7.1 <host-68-169-158-182.WISOLT2.epbfi.com[68.169.158.182]>: Client host rejected: Access denied; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<my-computer-name> Feb 25 19:33:52 myers postfix/smtpd[8044]: disconnect from host-68-169-158-182.WISOLT2.epbfi.com[68.169.158.182] Sending this through Microsoft Outlook 2003 generates the above log. However, sending through my iPhone, with the exact same settings, goes through fine: Feb 25 19:37:18 myers postfix/qmgr[3619]: A2D861302C9: from=<[email protected]>, size=1382, nrcpt=1 (queue active) Feb 25 19:37:18 myers amavis[2799]: (02799-09) FWD via SMTP: <[email protected]> -> <[email protected]>,BODY=7BIT 250 2.0.0 Ok, id=02799-09, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as A2D861302C9 Feb 25 19:37:18 myers amavis[2799]: (02799-09) Passed CLEAN, [68.169.158.182] [68.169.158.182] <[email protected]> -> <[email protected]>, Message-ID: <[email protected]>, mail_id: yMLvzVQJloFV, Hits: -9.607, size: 897, queued_as: A2D861302C9, 6283 ms Feb 25 19:37:18 myers postfix/lmtp[8752]: 2ED3A1302C8: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=6.6, delays=0.25/0.01/0.19/6.1, dsn=2.0.0, status=sent (250 2.0.0 Ok, id=02799-09, from MTA([127.0.0.1]:10025): 250 2.0.0 Ok: queued as A2D861302C9) Feb 25 19:37:18 myers postfix/qmgr[3619]: 2ED3A1302C8: removed Outgoing Settings on Outlook 2003 match the settings on my iPhone: SMTP server: mail.my-domain.com Username: My full email address Uses SSL Server Port 587 Now, here's postconf -n. I realize the "My Networks" Parameter is a bit nasty. I have these IP addresses in here for just this reason, as others have been complaining of this problem too: alias_database = hash:/etc/postfix/aliases alias_maps = $alias_database append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix content_filter = amavisfeed:[127.0.0.1]:10024 daemon_directory = /usr/libexec/postfix debug_peer_level = 2 disable_vrfy_command = yes html_directory = no inet_interfaces = all mail_owner = postfix mail_spool_directory = /var/spool/mail mailbox_size_limit = 0 mailq_path = /usr/bin/mailq manpage_directory = /usr/share/man message_size_limit = 20480000 mydestination = $myhostname, localhost, localhost.$mydomain mydomain = my-domain.com myhostname = myers.my-domain.com mynetworks = 127.0.0.0/8, 74.125.113.27, 74.125.82.49, 74.125.79.27, 209.85.161.0/24, 209.85.214.0/24, 209.85.216.0/24, 209.85.212.0/24, 209.85.160.0/24 myorigin = $myhostname newaliases_path = /usr/bin/newaliases queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES receive_override_options = no_address_mappings recipient_delimiter = + relay_domains = $mydestination sample_directory = /usr/share/doc/postfix-2.3.3/samples sendmail_path = /usr/sbin/sendmail setgid_group = postdrop smtp_bind_address = my-primary-server's IP address smtpd_banner = mail.my-domain.com smtpd_helo_required = yes smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/mailserver/postfix.pem smtpd_tls_key_file = /etc/ssl/mailserver/private/postfix.pem smtpd_tls_loglevel = 3 smtpd_tls_received_header = no smtpd_tls_session_cache_timeout = 3600s smtpd_use_tls = yes tls_random_source = dev:/dev/urandom unknown_local_recipient_reject_code = 554 virtual_alias_maps = mysql:/etc/postfix/mysql-virtual-alias-maps.cf,mysql:/etc/postfix/mysql-email2email.cf virtual_gid_maps = static:5000 virtual_mailbox_base = /var/vmail virtual_mailbox_domains = mysql:/etc/postfix/mysql-virtual-mailbox-domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql-virtual-mailbox-maps.cf virtual_minimum_uid = 5000 virtual_transport = dovecot virtual_uid_maps = static:5000 If anyone has any ideas and can help me finally solve this issue once and for all, I'd be eternally grateful.

  Read the article

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• Can't get network bridging to work

  - by Antonis Christofides

  I'm trying to make network bridging to work on a Debian squeeze (I'm experimenting in order to make a QEMU/KVM virtual machine that will be visible to the outside network as if it were a distinct machine). The problem is that when I type brctl addif br0 eth0 then I lose connectivity to the network until I type brctl delif br0 eth0. More specifically, here's how my machine looks like before I do anything (essentially eth0 is listening on 147.102.160.153): root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591848sec preferred_lft 604648sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever 3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 4c:ed:de:8e:44:d7 brd ff:ff:ff:ff:ff:ff 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether ee:7c:88:59:d0:e8 brd ff:ff:ff:ff:ff:ff Now let me add the bridge: root@laura:/home/anthony# brctl addbr br0 root@laura:/home/anthony# ip tuntap add dev tap0 mode tap root@laura:/home/anthony# ip link set tap0 up root@laura:/home/anthony# brctl addif br0 tap0 Until here everything continues to work normally. Finally, I try to add eth0 to the bridge: root@laura:/home/anthony# brctl addif br0 eth0 At this point, I no longer have a network connection. If I try to ping something, it tells "Destination Host Unreachable". The output of ip addr show seems normal: root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591908sec preferred_lft 604708sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever [snip wlan0, vboxnet0 and pan0, which are down and irrelevant] 8: br0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff 9: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500 link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff inet6 fe80::1430:f2ff:fe67:ab75/64 scope link valid_lft forever preferred_lft forever Also: root@laura:/home/anthony# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 147.102.160.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0.0.0.0 147.102.160.200 0.0.0.0 UG 0 0 0 eth0 I can't understand what I'm doing wrong. I want the machine to continue to listen on 147.102.160.153 on eth0, and in addition to that I want to have a tap0 interface, bridged to eth0, that will be available to the guest machine so that the latter listens on another ip address (say 147.102.160.205). (If there's another way to achieve what I want, I'm also interested.)

  Read the article

• OpenVPN on Tomato and Vista - can't see my network

  - by Ian

  I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

  Read the article

• PDFs and Networked Printers

  - by Bart Silverstrim

  Weird issue. We have users printing to networked windows-shared printers (print server Win2003 sp2). Some users have been reporting recently that they can't print PDF documents to particular printers (two example printers are HP 2430 PCL 6 driver and 4250 PCL 6 driver). At first, we found that on many of these systems the "Everyone" object was added to the permissions for the root of the C: volume but had no permissions checked. We added modify privileges to it (these are Deep-Freeze systems, so modifications to these systems that we don't add as administrators won't matter) and they seemed to be able to print. Perhaps Acrobat Reader was writing a temp file for printing where users didn't have permission, we surmised, and made the change and moved on. Yesterday the user called in saying it's not working still. Looked at it; bring up a PDF, click Print and the reader app says that you have to install a printer. Look at the printers folder (Windows XP workstation), and it has printers installed. Print a test page, return to AcroReader, and it will print fine to that printer. The whole time web pages, MS Office documents, etc. print without issue to the same printers. Has anyone seen this issue with Acro Reader 9 and certain network printer drivers or shares involving HP printers? I'd post this to SuperUser but it seems to be associated with a networked printer issue, seems to affect subsets of users but may be more widespread and our users aren't reporting it to us assuming we just know about it, and I've not found rhyme or reason as to why it's affecting just PDF printing and particular printers. The print spoolers are all running on the workstations and print server without errors being logged so far, but I'm going through the logs now to see if I can find anything out of place.

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• windows xp cannot access admin share

  - by barlop

  I have 3 systems. A,B,Compx all on xp. but comps A and B have an issue with Compx. Compx has network shares I can access. I can do \\compx and get some. But I cannot access the admin share c$ \\compx\c$ gives a login prompt, and I can't get any user/pass to work. I looked at permissions but don't see an issue. Nevertheless, I will describe what I see in the permissions. In the security tab of C, I have Administrators,creator owner,everyone,bob,system,users (6 things there) "creator owner" has nothing ticked, I can't seem to change that. If I tick so they all get ticked, and click apply, 2.5min and it's completed its opration and they all untick. Though this isn't the root of the problem. Since I get the same in the share I can access. In advanced, I see those 6 things, Administrators,creator owner,everyone,bob,system,users (6 things there) all "full control" all are "this folder, subfolders and files".. except creator owner, which is just subfolders and files only I look at the properties for the share I can see. looks the same, except in security..advanced, double clicking any of them the boxes are all ticked but greyed. That's not the problem though since I can access that share. So, I don't know what the problem is.

  Read the article

• Why does windows (file) explorer try to connect to port 80 (http) instead just using smb?

  - by Erik

  Background: On an almost freshly installed pc I get a message along the lines of : "windows cannot find some-file-server-name. Check the spelling and try again"... when trying to access any fileshare. Troubleshooting so far: pinging works. Both by ip and by name the almost identical pc next to this one can access the file server everyone else can access the file server the pc in question can not access other open fileshares but it can connect to the internet And now for what I think is the interesting part: running wireshark with ip.addr == local.ip.add.ress and ip.addr == server.ip.add.ress tells me that it tries to connect over http. the server replies but after a few messages back and forth it stops the other machine of course just uses smb I guess port 80 just means it defaults to webdav, but I haven't been able to find anything that can cause this. Googling it the closest thing I found was this http://www.techrepublic.com/article/get-vista-and-samba-to-work/6353849 but then again this was an XP pc and I wasn't able to connect to other native Windows shares (and I tried the solution anyway and it didn't work.)

  Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >