Search Results

Search found 20448 results on 818 pages for 'ip address'.

Page 91/818 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

  • VMWare steals IP addresses

    - by Ishan Amin
    I'm having a peculiar problem, that I think I have narrowed down to VMware. For the past one year, every once in a while we lose internet connection and not all users (about 10 users) go down at the same time, its usually one-by-one. First someone will call me and say "Internet is down" and then we would go reset the router and modem and switch and it would be working again for a while, then go down again without any pattern or replicatable sequence. We'd go repeat the steps again to get everyone in the office running again. We called our Internet Service Provider and they constantly say, We see your modem and we see your router and from thier end everything is OK. we replaced our router and switch and modem, twice! Last friday, it dawned upon me, that everytime we turn on a VMware machine, this sequence of taking everyone down starts, which also explains the message that my users get for "IP Conflict Found" So we do alot of VMware testing and lo and behold, it takes my Internet down. My Yahoo and Gtalk would continue working but www is down when the VMware machines are started. I do use bridged networking to all the VMware machines, but I dont know what else to set it at. now, sorry for this long rambling but anyone have any clue on how to stop this? thanks IA

    Read the article

  • What is the ip range of EC2

    - by Nicolas Kassis
    I'd like to setup a rule to block ssh request from EC2 since I've been seeing a large amount of ssh based attack from there and was wondering if anyone knew what their IP ranges are. EDIT: Thank you for the answer, I went ahead and implemented the iptables rules as follow. I ignore all traffic for the moment. Logging it just to see if the rules are working and for stats on how much crap EC2 is sending out ;) #EC2 Blacklist $IPTBLS -A INPUT -s 67.202.0.0/18 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 67.202.0.0/18 -j DROP $IPTBLS -A INPUT -s 72.44.32.0/19 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 72.44.32.0/19 -j DROP $IPTBLS -A INPUT -s 75.101.128.0/17 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 75.101.128.0/17 -j DROP $IPTBLS -A INPUT -s 174.129.0.0/16 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 174.129.0.0/16 -j DROP $IPTBLS -A INPUT -s 204.236.192.0/18 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 204.236.192.0/18 -j DROP $IPTBLS -A INPUT -s 204.236.224.0/19 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 204.236.224.0/19 -j DROP $IPTBLS -A INPUT -s 79.125.0.0/17 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 79.125.0.0/17 -j DROP

    Read the article

  • Apache2 Re-Routing from Domain Name to Internal IP Address

    - by Richard Grey
    The problem that I am having, is that when someone goes to my domain name example.co.uk, for some reason, apache seems to be re-routing the request to the internal IP address of the server, i.e. 192.168.0.52 My Apache2 default sites enabled file is as follows: ServerAdmin [email protected] ServerName trusteeguard.co.uk ServerAlias www.trusteeguard.co.uk DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/trusteeguard-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/trusteeguard-access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride All Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> This is an Ubuntu box if that is any help ;)

    Read the article

  • D-LINK DIR-615 router keeps giving my wireless devices bad ip addresses

    - by mlsteeves
    I have a D-LINK DIR-615 router, and wired devices have no problem getting an IP, however; wireless devices end up with a 169.254.. address (subsequently, they cannot access the internet through the router). I have removed all wired connections from the router, so there is no other dhcp server running. I've also gone back to the store, and replaced it with another, thinking that maybe it was defective. According to the router, it gave 192.168.0.101 to the wireless device. According to the wireless device it got 169.254.67.71. I've tried both a laptop and an iPod Touch, both exhibit the same behaviour. Has anyone seen this type of behaviour, or have any ideas of stuff to try? NEW INFORMATION I looked at the logs on the router, and when the wireless device tries to connect, this is what is logged: Sep 10 18:13:39 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:31 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:26 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:23 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:21 UDHCPD sending OFFER of 192.168.0.111 I connected a computer directly to the router, and here is what it looks like: Sep 10 18:14:18 UDHCPD Inform: add_lease 192.168.0.110 Sep 10 18:14:14 UDHCPD sending ACK to 192.168.0.110 Sep 10 18:14:14 UDHCPD sending OFFER of 192.168.0.110 Not sure if that helps or not.

    Read the article

  • Rate limiting bandwidth per IP

    - by Yohan
    First, I am not that good with computer. I even had problem with Windows PC. Right now I own a restaurant which happened to offer free internet. My ISP has my connection setup using a Ubuntu 11.1 box. IP Address is 192.168.1.16 with netmask 255.255.0.0, dns is 192.168.1.1 and gateway is 192.168.1.1. My problem is that my customers complains all day about slow network. When I received that kind of complain, the first thing came to my mind is to scout my area and find out who is the culprit, and ask him not to waste our bandwidth. Now, it is getting bored scouting people around, and I need to implement to my Linux box to limit bandwidth. I don't care if their provider can't be faster, but I want to limit 70kbit for each person. More annoying are people who use flashget and torrents. Usually they consume the biggest bandwidth. My question, how can I limit that? Please guide me in easy way. I've spent few days reading tc documents but doesn't understand a thing. I am using Ubuntu 11.10 Basically, I want all my customer get 70kbps each, no matter what.

    Read the article

  • Apache mod_proxy, how to forward request into local network ip(server)

    - by Beck
    Can't figure out, how to configure mod_proxy for this. I have two domains, one is working fine at the moment. Second is bind to the same ip. I need to forward requests from second domain to another server in local network. like that: domain1.com => 192.168.1.101 domain2.com => 192.168.1.102 What configuration or directives i should use? Thanks ;) Update <VirtualHost *:80> ServerName www.domain2.com ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://192.168.1.103:8080/ ProxyPassReverse / http://192.168.1.103:8080/ </VirtualHost> It just doesn't redirect to second server. That's it. And when i restart apache, it says something with overlapping 80 port. [warn] _default_ VirtualHost overlap on port 80, the first has precedence

    Read the article

  • Apache vhosts config: Host Name instead of IP Address

    - by Johe Green
    I have a domain (example.com) hosted at an external provider. I directed the subdomain sub.example.com to my ubuntu server (12.04 with apache2). On my ubuntu server I have a vhost setup like this. The rest of the config is basically apache 2 standard: <VirtualHost *:80> ServerName sub.example.com ServerAlias sub.example.com ServerAdmin [email protected] DocumentRoot /var/www/sub.example.com ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined WSGIScriptAlias / /home/application/sub.example.com/wsgi.py <Directory /home/application/sub.example.com> <Files wsgi.py> Order allow,deny Allow from all </Files> </Directory> </VirtualHost> When I enter http://sub.example.com in my browser my application shows up fine. But the domain is replaced by the IP address of my server. Do I have to configure my server somewhere else to deliver all its content under my domain sub.example.com?

    Read the article

  • Routing connections through VPN based on hostname (not IP range)

    - by Michal M
    This bugs me immensly. I need to connect to client's network through VPN. But I definitely do not want to send all the traffic through client's network so this option is out of question. What I need basically is for the OS to know that all client's network subdomains (*.example.com) need to go through the VPN connection. I tried a couple of options: Changing order of services and setting the VPN on top, but this works the same as "Send all traffic over VPN connection". Using "VPN on Demand" option from network advanced options, but this feature is quite rubbish to be honest. Seems to work only in Safari (?!) and it doesn't route the connection, but it basically triggers the OS to connect to the selected VPN. The reason I need it to work based on hostnames rather than IP range is simple - my client has a lot of servers inside his network and it's impossible for me to remember all IPs. They are all within a range, but this doesn't help me remembering. Another option would be to put the VPN connection on the bottom of network services and untick "Send all traffic..." and then put all known hostnames in hosts file, but considering there could be hundreds of servers (therefore hostnames and ips too) it ridiculous job. And if new server appears on the network I'd need to edit the hosts file again. Sisyphean labours. However this works on Windows very simply. If a hostname is not available through default network interface, then it seems to try VPN connection and this works brilliantly. So, how can I achieve that on Mac, then? I know client's internal DNS addresses if that is of any help (like directing a certain domains through a different DNS)? PS. Using latest version 10.6.6. PS2. I am using VPN to access intranet, version control servers (svn://), samba shares and for SSH access to servers.

    Read the article

  • "Unable to associated Elastic IP with cluster" in Eclipse Plugin Tutorial

    - by Jeffrey Chee
    Hi all, I am currently trying to evaluate AWS for my company and was trying to follow the tutorials on the web. http://developer.amazonwebservices.com/connect/entry.jspa?externalID=2241 However I get the below error during startup of the server instance: Unable to associated Elastic IP with cluster: Unable to detect that the Elastic IP was orrectly associated. java.lang.Exception: Unable to detect that the Elastic IP was correctly associated at com.amazonaws.ec2.cluster.Cluster.associateElasticIp(Cluster.java:802) at com.amazonaws.ec2.cluster.Cluster.start(Cluster.java:311) at com.amazonaws.eclipse.wtp.ElasticClusterBehavior.launch(ElasticClusterBehavior.java:611) at com.amazonaws.eclipse.wtp.Ec2LaunchConfigurationDelegate.launch(Ec2LaunchConfigurationDelegate.java:47) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:853) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:703) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:696) at org.eclipse.wst.server.core.internal.Server.startImpl2(Server.java:3051) at org.eclipse.wst.server.core.internal.Server.startImpl(Server.java:3001) at org.eclipse.wst.server.core.internal.Server$StartJob.run(Server.java:300) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55) Then after a while, another error occur: Unable to publish server configuration files: Unable to copy remote file after trying 4 timeslocal file: 'XXXXXXXX/XXX.zip' Results from first attempt: Unexpected exception: java.net.ConnectException: Connection timed out: connect root cause: java.net.ConnectException: Connection timed out: connect at com.amazonaws.eclipse.ec2.RemoteCommandUtils.copyRemoteFile(RemoteCommandUtils.java:128) at com.amazonaws.eclipse.wtp.tomcat.Ec2TomcatServer.publishServerConfiguration(Ec2TomcatServer.java:172) at com.amazonaws.ec2.cluster.Cluster.publishServerConfiguration(Cluster.java:369) at com.amazonaws.eclipse.wtp.ElasticClusterBehavior.publishServer(ElasticClusterBehavior.java:538) at org.eclipse.wst.server.core.model.ServerBehaviourDelegate.publish(ServerBehaviourDelegate.java:866) at org.eclipse.wst.server.core.model.ServerBehaviourDelegate.publish(ServerBehaviourDelegate.java:708) at org.eclipse.wst.server.core.internal.Server.publishImpl(Server.java:2731) at org.eclipse.wst.server.core.internal.Server$PublishJob.run(Server.java:278) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55) Can anyone point me to what I'm doing wrong? I followed the tutorials and the video tutorials on youtube exactly. Best Regards ~Jeffrey

    Read the article

  • Creating custom IP-STS for sharepoint foundation 2010 without ADFS

    - by user252229
    I plan to create very simple custom IP-STS for SharePoint foundation 2010 without ADFS server so anyone can integrate Windows Live ID to SharePoint foundation 2010 simply without ADFS, I can't use ADFS server because it could not install on Windows Web Server 2008 (Web Edition), also I found many article use LDAP provider but it does not exists in SharePoint Foundation too (it requires Sharepoint Server Edition). After too much searching I just found the following article and find all technique except one problem. 1) Creating Custom Claim Provider: blogs.technet.com/b/speschka/archive/2010/03/13/writing-a-custom-claims-provider-for-sharepoint-2010-part-1.aspx 2) Creating Custom STS Provider: http://blogs.msdn.com/b/chunliu/archive/2010/04/02/how-to-make-use-of-a-custom-ip-sts-with-sharepoint-2010-part-1.aspx Only one step remains: I got following error after enter username in STS site and redirect to localhost/_trust/default.aspx , ( I leave EncryptingCertificateName empty). Operation is not valid due to the current state of the object I expect to get access denied error instead of that error. 1.Is it possible anyway? 2.Can anyone help me where can I find working article to create custom IP-STS without ADFS server Any idea will help me Thanks

    Read the article

  • Processing a log to fix a malformed IP address ?.?.?.x

    - by skymook
    I would like to replace the first character 'x' with the number '7' on every line of a log file using a shell script. Example of the log file: 216.129.119.x [01/Mar/2010:00:25:20 +0100] "GET /etc/.... 74.131.77.x [01/Mar/2010:00:25:37 +0100] "GET /etc/.... 222.168.17.x [01/Mar/2010:00:27:10 +0100] "GET /etc/.... My humble beginnings... #!/bin/bash echo Starting script... cd /Users/me/logs/ gzip -d /Users/me/logs/access.log.gz echo Files unzipped... echo I'm totally lost here to process the log file and save it back to hd... exit 0 Why is the log file IP malformed like this? My web provider (1and1) has decide not to store IP address, so they have replaced the last number with the character 'x'. They told me it was a new requirement by 'law'. I personally think that is bs, but that would take us off topic. I want to process these log files with AWstats, so I need an IP address that is not malformed. I want to replace the x with a 7, like so: 216.129.119.7 [01/Mar/2010:00:25:20 +0100] "GET /etc/.... 74.131.77.7 [01/Mar/2010:00:25:37 +0100] "GET /etc/.... 222.168.17.7 [01/Mar/2010:00:27:10 +0100] "GET /etc/.... Not perfect I know, but least I can process the files, and I can still gain a lot of useful information like country, number of visitors, etc. The log files are 200MB each, so I thought that a shell script is the way to go because I can do that rapidly on my Macbook Pro locally. Unfortunately, I know very little about shell scripting, and my javascript skills are not going to cut it this time. I appreciate your help.

    Read the article

  • Experiences with (free) embedded TCP / IP stacks?

    - by Dan
    Does anyone have especially good (or bad) experiences with any of the following embedded TCP / IP stacks? uIP lwIP Bentham's TCP/IP Lean implementation The TCP/IP stack from this book My needs are for a solid, easy-to-port stack. Code size isn't terribly important, performance is relatively important, but ease of use & porting is very important. The system will probably use an RTOS, that hasn't been decided, but in my experience most stacks can be used with or without an RTOS. Most likely the platform will be an ARM variant (ARM7 or CM3 in all likelihood). Not too concerned about bolting the stack to the Ethernet driver, so that isn't a big priority in the selection. I'm not terribly interested in extracting a stack out of an OS, such as Linux, RTEMS, etc. I'm also not interested in commercial offerings such as Interniche, Micrium, etc... The stack doesn't need all sorts of bells & whistles, doesn't need IPv6, and I don't need any stuff on top of it (web servers, FTP servers, etc..) In fact it's possible that I'll only use UDP, although I can envision a couple scenarios where TCP would be preferable. Experiences with other stacks I've missed are of course also very much of interest. Thanks for your time & input.

    Read the article

  • Host ::1 resolves to remote IP

    - by thebuckst0p
    /etc/hosts files usually have this line, ::1 localhost. I thought ::1 was the equivalent of 127.0.0.1/localhost, and from my reading it seems to be the IPv6 version. So I was using it in Apache for firewalling, "Allow from ::1" and it only allowed local. Then suddenly that stopped working, so I pinged ::1 and got a remote IP address. I tracerouted it and it went through my ISP, through some Microsoft server, then another half dozen steps of asterisks... I'm not sure why this would be (the remote IP), but it doesn't seem good. I grep'd my hard drive for the remote IP and it doesn't appear anywhere. Is this some indicator that I'm being hacked, or normal behavior? Maybe my IPv6 settings are wrong? (This is a brand new MacBookPro with Snow Leopard.) Any ideas about this would be great - what is ::1 supposed to be, why would it be remote, should I be worried, how do I get it back to localhost? Thank you!

    Read the article

  • Serving east/west coasts with Geoipdns and MaxMind GeoLite data

    - by netvope
    I want to serve east (west) coast visitors with my Virginia (California) server. To do so, I plan to use Geoipdns and the IP-to-location mappings from MaxMind. MaxMind provide two datasets for free: GeoLite Country and GeoLite City. However, neither of them has east/west coast regions defined. A possible solution is to write a script to combine all the IP ranges for the east/west coast cities in GeoLite City, but that sounds a little bit stupid. What is the best practice in doing this? Any suggestions or alternatives?

    Read the article

  • How to access web server of any machine of my network from the outside

    - by Luc
    Hello, I have an ip like username.dyndns.org, this is the external IP of my router. On my lan, I have several machine (m1, m2, ...) , each running a dedicated web server. Is it possible to reach each machine from the outside with something like: http://m1.username.dyndns.org http://m2.username.dyndns.org ? Do you know what needs to be configured in my router for NAT ? Also, is there a special directive in Apache to do so ? Thanks a lot, Regards, Luc

    Read the article

  • cannot access localhost using ip

    - by Robert
    I have done a small web development project using eclipse. It runs well when I try running it on browser with url localhost:8080/myproject/home.html. But if I want to access it on another machine (laptop, mobile, etc. using the same wifi) it is not possible; it is not able to connect. After Googling for a while found out that I have to use the IP address instead of 'localhost'. So I tried 10.0.0.4:8080/myproject/home.html, but still does not work. In fact i am unable to open that url on the same machine (where localhost:8080/myproject/home.html works fine). I also added a new Inbound rule in control panel firewall settings, allowing access to all ports for protocol TCP. Still have problem in running application with the url 10.0.0.4:8080/myproject/home.html (both on same machine as well as laptop and mobile). FYI i am using Eclipse Indigo, Apache tomcat 6.0 and server.xml file contents is as below: <?xml version="1.0" encoding="UTF-8"?> <!-- Licensed to the Apache Software Foundation (ASF) under one or more contributor license agreements. See the NOTICE file distributed with this work for additional information regarding copyright ownership. The ASF licenses this file to You under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. --><!-- Note: A "Server" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/server.html --><Server port="8005" shutdown="SHUTDOWN"> <!--APR library loader. Documentation at /docs/apr.html --> <Listener SSLEngine="on" className="org.apache.catalina.core.AprLifecycleListener"/> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener"/> <!-- Prevent memory leaks due to use of particular java/javax APIs--> <Listener className="org.apache.catalina.core.JreMemoryLeakPreventionListener"/> <!-- JMX Support for the Tomcat server. Documentation at /docs/non-existent.html --> <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener"/> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener"/> <!-- Global JNDI resources Documentation at /docs/jndi-resources-howto.html --> <GlobalNamingResources> <!-- Editable user database that can also be used by UserDatabaseRealm to authenticate users --> <Resource auth="Container" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" name="UserDatabase" pathname="conf/tomcat-users.xml" type="org.apache.catalina.UserDatabase"/> </GlobalNamingResources> <!-- A "Service" is a collection of one or more "Connectors" that share a single "Container" Note: A "Service" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/service.html --> <Service name="Catalina"> <!--The connectors can use a shared executor, you can define one or more named thread pools--> <!-- <Executor name="tomcatThreadPool" namePrefix="catalina-exec-" maxThreads="150" minSpareThreads="4"/> --> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" protocol="HTTP/1.1" address="10.0.0.4" connectionTimeout="20000" redirectPort="8443" /> <!-- A "Connector" using the shared thread pool--> <!-- <Connector executor="tomcatThreadPool" port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> --> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" /> --> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443"/> <!-- An Engine represents the entry point (within Catalina) that processes every request. The Engine implementation for Tomcat stand alone analyzes the HTTP headers included with the request, and passes them on to the appropriate Host (virtual host). Documentation at /docs/config/engine.html --> <!-- You should set jvmRoute to support load-balancing via AJP ie : <Engine name="Catalina" defaultHost="localhost" jvmRoute="jvm1"> --> <Engine defaultHost="localhost" name="Catalina"> <!--For clustering, please take a look at documentation at: /docs/cluster-howto.html (simple how to) /docs/config/cluster.html (reference documentation) --> <!-- <Cluster className="org.apache.catalina.ha.tcp.SimpleTcpCluster"/> --> <!-- The request dumper valve dumps useful debugging information about the request and response data received and sent by Tomcat. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve"/> --> <!-- This Realm uses the UserDatabase configured in the global JNDI resources under the key "UserDatabase". Any edits that are performed against this UserDatabase are immediately available for use by the Realm. --> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <!-- Define the default virtual host Note: XML Schema validation will not work with Xerces 2.2. --> <Host appBase="webapps" autoDeploy="true" name="localhost" unpackWARs="true" xmlNamespaceAware="false" xmlValidation="false"> <!-- SingleSignOn valve, share authentication between web applications Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Access log processes all example. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" directory="logs" prefix="localhost_access_log." suffix=".txt" pattern="common" resolveHosts="false"/> --> <Context docBase="myproject" path="/myproject" reloadable="true" source="org.eclipse.jst.jee.server:myproject"/></Host> </Engine> </Service> </Server>

    Read the article

  • C standard addressing simplification inconsistency

    - by Chris Lutz
    Section §6.5.3.2 "Address and indirection operators" ¶3 says (relevant section only): The unary & operator returns the address of its operand. ... If the operand is the result of a unary * operator, neither that operator nor the & operator is evaluated and the result is as if both were omitted, except that the constraints on the operators still apply and the result is not an lvalue. Similarly, if the operand is the result of a [] operator, neither the & operator nor the unary * that is implied by the [] is evaluated and the result is as if the & operator were removed and the [] operator were changed to a + operator. ... This means that this: int *i = NULL; printf("%p", (void *) (&*i) ); printf("%p", (void *) (&i[10]) ); Should be perfectly legal, printing the null pointer (probably 0) and the null pointer plus 10 (probably 10). The standard seems very clear that both of those cases are required to be optimized. However, it doesn't seem to require the following to be optimized: struct { int a; short b; } *s = 0; printf("%p", (void *) (&s->b) ); This seems awfully inconsistent. I can see no reason that the above code shouldn't print the null pointer plus sizeof(int) (possibly 4). Simplifying a &-> expression is going to be the same conceptually (IMHO) as &[], a simple address-plus-offset. It's even an offset that's going to be determinable at compile time, rather than potentially runtime with the [] operator. Is there anything in the rationale about why this is so seemingly inconsistent?

    Read the article

  • data path (travel) of tcp data from "write" syscall downto I/O registers programming

    - by osgx
    Hello Is there a good overview of tcp data path in Linux (2.6, not 2.4 if the path actually differ)? Where is a packet on different stages of tcp/ip stack handling? How packet is packed to tcp segment, then ip packet. How it is transmitted to network card? (with series of I/O regs write and DMA?) Is it transmitted to network card in the "write" syscall handler (with some deep callstack) or is it transmitted at some other moment?

    Read the article

  • DNS Problem in my notebook [closed]

    - by air
    i have windows 2003 server domain environment in my office. my server ip is: 192.168.1.2 if i put this IP in DNS of my laptop network card my folder SYNC works fine & also internet work fine in office. but internet did't work in my home for that i need to change DNS again to Auto & internet start working again. its too difficult to change cause some time i don't have administrative password. is there any solution to that? Thanks

    Read the article

  • What library to use to create a simple port scanner?

    - by durje
    I need advise to create a simple port-scanner, who will need to detect if some specific devices are connected to the network from theire IP/MAC address. I am working on windows 7 and can use preferably C++ Builder 2010 Embarcadero, or java or Qt. The library have to be under a public domain or equivalent, as my software is a proprietary software. What library would you advice? Do you know any free software that I could start from, or any examples? What about using Indy Sockets or Synapse TCP/IP Librarys? Thanks in advance.

    Read the article

  • Apache: VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not sup

    - by user45761
    Hi, when i add the line below to /etc/apache2/apache2.conf I get the error belower when i restart apache: Include /usr/share/doc/apache2.2-common/examples/apache2/extra/httpd-vhosts.conf [Mon Jun 14 12:16:47 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Mon Jun 14 12:16:47 2010] [warn] NameVirtualHost *:80 has no VirtualHosts This is my httpd-vhosts.conf file: # # Use name-based virtual hosting. # NameVirtualHost *:80 # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. <VirtualHost *:80> ServerName tirengarfio.com DocumentRoot /var/www/rs3 <Directory /var/www/rs3> AllowOverride All Options MultiViews Indexes SymLinksIfOwnerMatch Allow from All </Directory> Alias /sf /var/www/rs3/lib/vendor/symfony/data/web/sf <Directory "/var/www/rs3/lib/vendor/symfony/data/web/sf"> AllowOverride All Allow from All </Directory> </VirtualHost> Any idea? Regards Javi

    Read the article

  • Apache: VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not sup

    - by user45761
    Hi, when i add the line below to /etc/apache2/apache2.conf I get the error belower when i restart apache: Include /usr/share/doc/apache2.2-common/examples/apache2/extra/httpd-vhosts.conf [Mon Jun 14 12:16:47 2010] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results [Mon Jun 14 12:16:47 2010] [warn] NameVirtualHost *:80 has no VirtualHosts This is my httpd-vhosts.conf file: # # Use name-based virtual hosting. # NameVirtualHost *:80 # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. <VirtualHost *:80> ServerName tirengarfio.com DocumentRoot /var/www/rs3 <Directory /var/www/rs3> AllowOverride All Options MultiViews Indexes SymLinksIfOwnerMatch Allow from All </Directory> Alias /sf /var/www/rs3/lib/vendor/symfony/data/web/sf <Directory "/var/www/rs3/lib/vendor/symfony/data/web/sf"> AllowOverride All Allow from All </Directory> </VirtualHost> Any idea? Regards Javi

    Read the article

  • Cisco Pix 501 - reaching local host limit, showing odd IP addresses

    - by cdonner
    I am running out of licenses on my Pix 501, and the show local-host command lists a number of odd IP addresses that do not belong to my 10.10.1.* subnet. Any idea what they are? The only thing I could find was a potential ISP: DINSA is Defence Interoperable Network Services Authority, an agency of the Ministry of Defence of the United Kingdom. Does not sound right. I don't see any active connections, though. I can't ping or traceroute these IPs, but they reappear after I clear the list, with various other addresses in that general range, up until the connection limit is reached. Based on the number denied, I suppose I would have a lot more of them had I not the connection limit. Very dubious. Is anybody else seeing this? pixfirewall# show local-host Interface inside: 10 active, 10 maximum active, **118 denied** local host: <10.10.1.110>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.176>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.170>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 1/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.175>, TCP connection count/limit = 11/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 1/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.108>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.33.41.115>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.33.226.124>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.172>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.36.114.91>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.109>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): pixfirewall#

    Read the article

  • Sending USR2 to mongrel_rails sometimes results in an “Address already in use” on the restart

    - by Ben
    We have a rolling-restart mode for our mongrel cluster that sends a USR2 signal to each running process. This works great, most of the time. But very occasionally the mongrel process will shutdown, and then fail to restart, with the following error: /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize_without_backlog': Address already in use - bind(2) (Errno::EADDRINUSE) from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `listener' Looking though the mongrel source, the USR2 handler calls a synchronous stop on the running server, so it ought to block until the socket has been released. Has anyone seen this error? Does anyone have any ideas what might cause it? (I asked this question over on StackOverflow initially, but thought it might be more appropriate here)

    Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >