Search Results

Search found 49518 results on 1981 pages for 'configuration files'.

Page 913/1981 | < Previous Page | 909 910 911 912 913 914 915 916 917 918 919 920  | Next Page >

• HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

  - by Marek L.

  I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

  Read the article

• Ubuntu installer doesn't see internal hard drive on DELL Vostro 3360

  - by valk

  I just received a new DELL Vostro 3360, it has Windows 7 preinstalled. When it comes to the partition window I can't see the hard drive there. I see only /dev/sda or /dev/sdb (either one and in both cases it's a usb drive from which I'm installing). I tried every imaginable BIOS configuration. Tried to change the SATA mode to ATA, DHCI and more. EDIT: I tried to install with standard Ubuntu 12.04 32 bit, and 11.10 64 bit official versions. No luck. I'll appreciate any suggestion.

  Read the article

• Telesharp: An application metadata repository that enables true agility in enterprise .NET applications.

  - by Vishal

  Tellago Studios proudly announces its newest product, a third one within a year of time : TELESHARP .NET Configuration Management has always been a nightmare for any enterprise. TeleSharp is an innovative product that addresses the most common challenges of .NET applications in the enterprise. After years of struggle developing and managing large .NET applications, we decided to create a tool that makes .NET applications truly agile. You can read more about Telesharp and what difference it can make into your enterprise. Also if you want to see Telesharp in action, check the videos about it. Click here to get more information about TeleSharp trial version! Click here to register for the TeleSharp webinar on July 6th from 2PM - 3PM EST.   -Vishal

  Read the article

• DriveImage XML fails with a Windows Volume Shadow Service Error

  - by ssvarc

  I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

  Read the article

• WCF Keep Alive: Whether to disable keepAliveEnabled

  - by Lijo

  I have a WCF web service hosted in a load balanced environment. I do not need any WCF session related functionality in the service. QUESTION What are the scenarios in which performances will be best if keepAliveEnabled = false keepAliveEnabled = true Reference From Load Balancing By default, the BasicHttpBinding sends a connection HTTP header in messages with a Keep-Alive value, which enables clients to establish persistent connections to the services that support them. This configuration offers enhanced throughput because previously established connections can be reused to send subsequent messages to the same server. However, connection reuse may cause clients to become strongly associated to a specific server within the load-balanced farm, which reduces the effectiveness of round-robin load balancing. If this behavior is undesirable, HTTP Keep-Alive can be disabled on the server using the KeepAliveEnabled property with a CustomBinding or user-defined Binding.

  Read the article

• How to Search File Contents in Windows Server 2008 R2

  - by ybbest

  By default, windows search only search by File name. To configure windows search to search by contents you need configure the following: You need to make sure Windows Search Services feature is activated.(Check this article for details) Then, configure Windows Search by Open file explorer: Press Alt button –> go to tools –> Folder options –> search tab –> Here select, “Always search file names and content(this might take several minutes)” Press okay. Now your searches will work for file content like the good old days of XP. Another way to search the contents in file without Search configuration is to Type “contents:” in the Windows Explorer search box followed by the word, searches text files. This is a search filter which seems to be undocumented?

  Read the article

• How can I do a large file upload using Sinatra, haml, nginx, and passenger?

  - by mmr

  Hi all, I need to be able to allow a user to upload 30-60 mb files at a time. Right now, I'm solving the problem with a simple form post: %form{:action=>"/Upload",:method=>"post",:enctype=>"multipart/form-data"} - @theModelHash.each do |key,value| %br %input{:type=>"checkbox", :name=>"#{key}", :value=>1, :checked=>value} =key %br %input{:type=>"file",:name=>"file"} %input{:type=>"submit",:value=>"Upload"} This form allows the user to select processing options contained in theModelHash and upload a file for processing. Problem is, this method both freezes the user's UI and also requires that the entire form be reposted when the user presses the 'back' button. I've looked at SWFUpload, but have no idea how to integrate that into my relatively simple app. There's a page here about integrating it with Rails, but I'm using Sinatra, and am new enough to this whole web programming thing that I don't know how to modify those files to work with what I need to do. Is there a how-to to add large file uploads to my form there? Something relatively simple that just adds in a progress bar and doesn't repost? I feel like I'm having to triple the size of my application just to make this feature play nice, and that's bothering me a bit.

  Read the article

• Active FTP client blocked on Windows XP

  - by Ian Hannah

  Summary We have a FTP server (running in active mode). We have an FTP client which is connecting to the server, carrying out a task and then closing the connection. The FTP Client can perform this operation on multiple threads. Problem We have a situation where customers are experiencing occasional failures to carry out operations on a FTP connection. The actual connection has been made to the server but when the server attempts to return data on the data port if fails. Observations We have a simple test FTP client which is running two separate threads. Each thread is performing a recursive listing of files from a root directory. With the firewall running on the client machine the hang happens within a few minutes. If the firewall is turned off on the client machine, the test application seems to run correctly. This does point to a potential firewall issue. However, with the firewall on we can list files on our company FTP server without any issues. If the simple test FTP client runs a single thread then we do not experience any problems whether or not the firewall is turned on. We have another simple test FTP client which was running 4 threads (with each opening a new FTP connection, doing a directory listing and closing the FTP connection as fast as possible) overnight with the firewall turned off. With the firewall turned on it fails in a short space of time. The confusing thing is that if the test FTP client and the FTP server are run on the same machine the failure occurs even though the firewall is turned off. This means that the problem may not be firewall related. Any help with what this could be would be much appreciated. Thanks Ian

  Read the article

• Merging cuesheet chapter halves into single track for an audiobook

  - by TheSavo

  I have an audiobook that I have ripped and I need some help constructing chapters. I have already made some cue sheets TITLE "Bookname" PERFORMER "the Author" FILE "File1.FLAC" wave ; 23971906.667 milliseconds TRACK 01 AUDIO TITLE "_Intro" INDEX 01 00:00:00 TRACK 02 AUDIO TITLE "CH 01" INDEX 01 24:15:50 TRACK 03 AUDIO TITLE "CH 02" INDEX 01 66:21:00 TRACK 04 AUDIO TITLE "CH 03" INDEX 01 87:05:00 The audio book is in two files. The chapter at the end of the first file is continued in the second file. However, the second file restates: The publisher Book Title List item Blah blah blah I would like to merge the two 'halves' of the chapter in one seamless track. The only way I can think to do this would be be: Bulk cut down the tracks. Drop the junk info into junk track Continue the track listings as normal Take the two "halves" of the target chapter and build a separate cue sheet for it. I know there has to be an easier way. I am ok with making the 'junk' info a 'gap' or something. These are are FLAC files that will be converted to MP3 for my phone and other potable devices. I have read the primers on cue sheets, but I am just not getting it.

  Read the article

• Conditionally permitting HTTP-only requests to Tomcat?

  - by Mike

  I have 2 versions of a system: Tomcat webserver Nginx reverse-proxy sitting in front of a tomcat webserver. In version 2, nginx only ever talks to Tomcat over HTTP. A user could configure the system so that only HTTPS requests are allowed. If the user does this in Version 1 and then the XML configuration files for Tomcat takes care of this. In version 2, nginx takes care of this. The problem is this: I cannot force a user to update their Tomcat XML config files when they upgrade from version 1 to version 2 (it will be recommended that they do so) because this is done as part of a larger process. This means that if they upgrade and don't update the Tomcat config, an HTTPS request will arrive at nginx, which will proxy it over HTTP to Tomcat which will reject the request because it is not HTTPS. So I can't force an update to the Tomcat XML, and I have to use HTTP between nginx and Tomcat. Any ideas? Is there some way I can affect how Tomcat reads its config in Version 2 so that it ignores the HTTPS-only section?

  Read the article

• unreadable corrupted ntfs partition - lost clusters reported

  - by Eduardo Martinez

  Hi, partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

  Read the article

• Failed to retrieve share list from server

  - by Eric Sean Tite Webber

  UBUNTU 11.10 NAUTILUS 3.2.1 We ARE able to see Windows PCs on our network from Ubuntu's NAUTILUS, yet we are NOT able to access their shares from NAUTILUS, even though they work fine with each other, i.e. each windows PC IS able access the other Windows PC's shares just fine. Please infer from this information the answers to any questions about our situation you may have. Note this is a default/pristine configuration, i.e. no changes have been made whatsoever. Our version of Ubuntu is: 11.10, NAUTILUS is 3.2.1 Linux tite-HP-630-Notebook-PC 3.0.0-15-generic #26-Ubuntu SMP Fri Jan 20 17:23:00 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux A screenshot is available upon request. Thanks in advance for your assistance.

  Read the article

• APC uptime 0 because of Fast

  - by demlasjr

  I have a VPS using Parallels/Plesk (11.0.9 Update #22, last updated at Oct 31, 2012 03:33 AM CentOS 6.3 (Final) x86_64) I have apache (CGI/FastCGI) installed and nginx as reverse proxy. Everything is working just fine. I installed APC for caching, but the issue is that the uptime is 0 always. It's restarting each 15 seconds or so. I checked everywhere and can't find a solution to fix it. The server have the grace restart enabled, but every 6 hours, which shouldn't influence the APC uptime. Searching in Google I found that this could be related to Apache, running with FCGId instead of FastCGI. Plesk/Apache is using this config file: usr/local/psa/admin/conf/templates/default/service/php_over_fastcgi.php which content is: <IfModule mod_fcgid.c> <Files ~ (\.php)> SetHandler fcgid-script FCGIWrapper <?php echo $VAR->server->webserver->apache->phpCgiBin ?> .p$ Options +ExecCGI allow from all </Files> Is here the issue or elsewhere ? How can I fix this to work with FastCGI and make APC working properly. I forgot to specify that even if the uptime is below one minute, APC is doing pretty good job caching (92% are hits).

  Read the article

• AspNetCompatibility in WCF Services &ndash; easy to trip up

  This isnt the first time Ive hit this particular wall: Im creating a WCF REST service for AJAX callbacks and using the WebScriptServiceHostFactory host factory in the service: <%@ ServiceHost Language="C#" Service="WcfAjax.BasicWcfService" CodeBehind="BasicWcfService.cs" Factory="System.ServiceModel.Activation.WebScriptServiceHostFactory" %>   to avoid all configuration. Because of the Factory...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update

  - by tags2k

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• How to get current gnome keyboad layout from terminal

  - by ftiaronsem

  For usage in a bash script, I need to get the gnome keyboard layout the user is currently using. For example if the user sets its keyboard layout to en-us , I need a bash command that prints me this. How can I get that information? Update: setxkbmap -query is unfortunatelly not working. Below is the ouput with the en (first command) and the de (second command) layout activated. Switching keyboard layout seems to be have some relation with gnome session configuration setxkbmap -query rules: evdev model: pc105 layout: us,de variant: , options: terminate:ctrl_alt_bksp,lv3:ralt_switch,grp:alts_toggle setxkbmap -query rules: evdev model: pc105 layout: us,de variant: , options: terminate:ctrl_alt_bksp,lv3:ralt_switch,grp:alts_toggle

  Read the article

• Lucid Lynx login issue

  - by Bart Silverstrim

  Recently upgraded from Karmic to Lynx. Upgrade seemed to go well, no noticeable issues. I logged in, and my window manager wasn't starting. An application would appear, but sans control buttons and border, so figured the windows manager needed to be given a swift kick. Opened a web browser and a quick google had me run "metacity --replace &" and everything popped up. I re-ran the Compiz configuration tool to enable my rotating desktop cube to the way I liked it, and had to reconfigure my desktop switcher to the right number of desktops (although the first time I ran it, it crashed on the panel and reloaded...odd, but once it relaunched it seemed fine.) Today I installed updates, rebooted and logged in for the second time since my upgrade. Again, the window manager was dead, and my compiz settings were gone, and the workspaces were set back to four (and when I clicked on the preferences to change them, it crashed on the panel and reloaded again). Resetting everything made things look somewhat normal again. I'm guessing it'll work until I reboot again. Googling around isn't turning up similar complaints about Lucid Lynx and the window manager. Before I go deleting preference files, anyone else know of this kind of issue and what could be done about it? Or should I start taking the stab in the dark approach of deleting preference files hoping one of them is corrupt or has something unsupported in it that's throwing LL for a loop?

  Read the article

• Translating error messages from an external API?

  - by Jan Fabry

  If I am localizing a piece of software that uses an external API, how should I handle error messages that originate in this API? I do not control the API, I only consume it. The error responses are not very structured: some contain error codes, some contain verbose details in the text, others almost nothing. Some errors can be fixed by the user (incorrect configuration), some are caused by the external service (server overload), some could be caused by a bug in my software (of course, this would be very unlikely...). I would like to provide a smooth experience to my end-users, so they know what went wrong and what they can do to fix it. What is the best strategy to use here? (This is a generalization of a question from the WordPress Stack Exchange. I thought it would be worth re-asking here, because it is not limited to WordPress plugins.)

  Read the article

• sysctl.conf ignore net settings

  - by Steffen Unland

  I have a little problem with sysctl on a Ubuntu 10.04 LTS system. When I set the sysctl values with "sysctl -w " all work fine, but when I try to use the sysctl.conf file. the net settings will be ignored. For example my sysctl.conf # /etc/sysctl.conf - Configuration file for setting system variables kernel.domainname=findme.sysctl # Corefiles information fs.suid_dumpable=2 kernel.core_pattern=/cores/core-%e-%s-%u-%g-%p-%t ##############################################################3 # Functions previously found in netbase net.ipv4.netfilter.ip_conntrack_tcp_timeout_fin_wait=1 net.ipv4.netfilter.ip_conntrack_tcp_timeout_close_wait=1 when I grep to the values, I can see that the sysctl settings for net.ipv4.netfilter don't set. [host:~ ] $ sysctl -a | grep domainname kernel.domainname = findme.sysctl [host:~ ] $ sysctl -a | grep "core_pattern" kernel.core_pattern = /cores/core-%e-%s-%u-%g-%p-%t [host:~ ] $ sysctl -a | grep "timeout_fin_wait" net.netfilter.nf_conntrack_tcp_timeout_fin_wait = 120 net.ipv4.netfilter.ip_conntrack_tcp_timeout_fin_wait = 120 [host:~ ] $ sysctl -a | grep "timeout_close_wait" net.netfilter.nf_conntrack_tcp_timeout_close_wait = 60 net.ipv4.netfilter.ip_conntrack_tcp_timeout_close_wait = 60 can somebody help me to solve the problem? If you need more information I can post it. Cheers, Steffen

  Read the article

• Why can't I open file with doubleklick after I moved the application that opens it on windows?

  - by Glen S. Dalton

  I am on windows server 2003, but I guess it is the same on windows xp. I moved some movable applications (usually people create them for usb sticks) to locations like c:\bin\app1\app1.exe. The old location was c:\programs\app1\app1.exe app1.exe can open files of type *.ap1 When I rightclick file.ap1 and choose open with ... the Open with dialog appears. But it is not working how I expect in this situation. I can choose c:\bin\app1\app1.exe with the "Browse" button, but: app1.exe will not appear in the dialog where I just choosed it in the programs list, like I am used to it after clicking OK on it in the browse dialog. app1.exe will not open it when I click ok in the "Open with" dialog, the application that was assigned until then will still open it What could be the reason? my account is member of the administrators group I just changed the permissions of the folder c:\bin\app1\ and made sure that the group "Administrators" has all rights. I also inherited this manually to all subfodlers and subfiles. I also tried to move the application (with the whole folder) to "c:\program files\app1\app1.exe

  Read the article

• How do I verify the ownership of a domain from Namecheap to use Google Apps?

  - by Rook

  I registered a domain with Namecheap.com, and started the Google Apps registration process. After the initial data filling, google apps wishes me to prove the ownership of a domain, and has given me 4 choices: Add a DNS record to your domain's configuration Link to your Google Analytics account Upload an HTML file to your server Add a meta tag to your site's home page What is the differences between these, and how do I (if someone knows perhaps how to do it on Namecheap, it would be even better) complete this step in the process? I would appreciate any advice you might have.

  Read the article

• Split MPEG video from command line?

  - by Tim

  I have a homemade DVD that I'm effectively trying to insert chapters into and rearrange - the original author burned it as one long chapter, and I'd like to rip it into smaller pieces and re-encode it into a new DVD. I ripped the DVD with the following command: mplayer dvd:// -dvd-device /dev/sr2 -dumpstream -dumpfile raw.vob I'm running Gentoo Linux with mplayer version 1.0-rc2_p20090731 (the latest available in Portage). I have a list of times that the chapters are supposed to span (for example 30:11-33:25), so my first thought was to rip the entire DVD and use mpgtx to cut out certain pieces of the file. My issue is that running mpgtx -i on the file reports quite a few timestamp jumps: Time stamps jumped from 59.753789 to 0.001622 at position 1d29800 Time stamps jumped from 204963823030450.343750 to 31.165900 at position 2d4f800 Time stamps jumped from 60.077878 to 0.001622 at position 43cc000 Time stamps jumped from 60.024233 to 0.001622 at position 65c5000 Time stamps jumped from 204963823068631.718750 to 52.549244 at position 7fd1000 I've tried to fix the indexes using: mencoder raw.vob -oac copy -ovc copy -forceidx -o fixed.vob -of mpeg But mpgtx will still report timestamp issues. My immediate question: is there a way to take the ripped movie I have and correct its timestamps so I can cut it with mpgtx? If I can get that one issue out of the way, building the rest of the DVD will be smooth sailing. If it's not possible to fix the timestamps on this file: is there a better way to rip small chunks of the DVD into separate files for recompilation later? I'd very much like this to be done on Linux, and it'd be even better if I could script it somehow (feed in a list of start and end positions, or start times and durations, and get out a series of ripped files). If need be, I also have a Mac OS X machine available, but no Windows. Edit: I wound up finding another solution involving HandBrake and ffmpeg (with help from this question), but the question stands. Edit again: Turns out my other solution didn't quite work - the audio desynchronized by about five seconds, in about half of my cut mpgs - so I'm back to square one. Anyone?

  Read the article

• Cannot assign keys to Wacom scroll wheel anymore

  - by UncleZeiv

  Hi all, my Wacom Graphire 4 used to work perfectly well until, I think, Ubuntu 10.4. At that point something changed in the configuration and I couldn't assign a key to the scroll wheel anymore (note: the pad's scroll wheel, not the mouse's), i.e this command: xsetwacom set "Wacom Graphire4 6x8 pad" AbsWDn "key +" returns silently without error but nothing happens. Same goes for AbsWUp, RelWDn, RelWUp. Apparently though the problem is even deeper as pressing the wheel in a xev window doesn't seem to have any effect. Moreover I am thoroughly confused on how the various pieces (kernel driver, xorg driver, evdev, HAL, xinput?) are supposed to work together and if the wacom module that ships with Ubuntu is the one from linuxwacom or not. Any ideas? I don't want to become an X.org hacker just to understand what's going on... it used to work! NOTE: I have already read question 3940, but that's not the same problem.

  Read the article

• Dual monitor in Ubuntu 12.04 + Nvidia GPU with CUDA drivers?

  - by Aphex

  I'm thinking about setting up dual monitors on my desktop PC, running Ubuntu 12.04 with a Nvidia GTX 570. I use the GPU for CUDA programming so it's set up with the CUDA drivers. Is it possible/easy to set up dual monitors with this configuration? The only questions I saw related to this were for GPUs without cuda drivers. If anyone knows how dual monitors work with CUDA drivers, it would be much appreciated. It was enough of a pain getting everything running with the GPU and CUDA in the first place, I'd hate to ruin it all by attempting dual monitors.

  Read the article

• Tcpreplaying using VMware

  - by Methos

  This is more like a testbed setup question. I want to use VMware to debug some networking code in the linux kernel in the VM. My VM has two network interfaces. What I want to do is replay the capture file in the host and receive the packets in the VM. My problem is I do not see replayed packets in the VM. I am running VMware and tcpreplay on the host as sudo. Hence I think there should not be any problem access devices files. I am running VMware workstation 7.0 a. I first began with Custom networking as that provides option of creating your own virtual network name. I wrote /dev/vmnet3 and /dev/vmnet4 for the two interfaces respectively. However, after booting the guest, I did not see any of these interfaces or devices files (in /dev) created on the host. b. Then I tried 'Host Only', but that does not show what bridge/device file is associated with the interface. c. Finally I tried bridged networking mode. I see vmnet1, vmnet8 and vboxnet0 on the host. I have tcpreplayed the capture file on each of these interfaces, for all the above three cases. I tried to capture packets in the VM using "tcpdump -i any". However, I do not see any packets. Any ideas/pointers?

  Read the article

< Previous Page | 909 910 911 912 913 914 915 916 917 918 919 920  | Next Page >