Search Results

Search found 2733 results on 110 pages for '02 javafx'.

Page 92/110 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Installing Lubuntu 14.04.1 forcepae fails

  - by Rantanplan

  I tried to install Lubuntu 14.04.1 from a CD. First, I chose Try Lubuntu without installing which gave: ERROR: PAE is disabled on this Pentium M (PAE can potentially be enabled with kernel parameter "forcepae" ... Following the description on https://help.ubuntu.com/community/PAE, I used forcepae and tried Try Lubuntu without installing again. That worked fine. dmesg | grep -i pae showed: [ 0.000000] Kernel command line: file=/cdrom/preseed/lubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- forcepae [ 0.008118] PAE forced! On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Finally, I rebooted once more and tried Check disc for defects with forcepae option; no errors have been found. Now, I am wondering how to find the error or whether it would be better to follow advice c in https://help.ubuntu.com/community/PAE: "Move the hard disk to a computer on which the processor has PAE capability and PAE flag (that is, almost everything else than a Banias). Install the system as usual but don't add restricted drivers. After the install move the disk back." Thanks for some hints! Perhaps some of the following can help: On Lubuntu 12.04: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr mce cx8 mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2 bogomips : 1284.76 clflush size : 64 cache_alignment : 64 address sizes : 32 bits physical, 32 bits virtual power management: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise cpuid eax in eax ebx ecx edx 00000000 00000002 756e6547 6c65746e 49656e69 00000001 000006d6 00000816 00000180 afe9f9bf 00000002 02b3b001 000000f0 00000000 2c04307d 80000000 80000004 00000000 00000000 00000000 80000001 00000000 00000000 00000000 00000000 80000002 20202020 20202020 65746e49 2952286c 80000003 6e655020 6d756974 20295228 7270204d 80000004 7365636f 20726f73 30352e31 007a4847 Vendor ID: "GenuineIntel"; CPUID level 2 Intel-specific functions: Version 000006d6: Type 0 - Original OEM Family 6 - Pentium Pro Model 13 - Stepping 6 Reserved 0 Brand index: 22 [not in table] Extended brand string: " Intel(R) Pentium(R) M processor 1.50GHz" CLFLUSH instruction cache line size: 8 Feature flags afe9f9bf: FPU Floating Point Unit VME Virtual 8086 Mode Enhancements DE Debugging Extensions PSE Page Size Extensions TSC Time Stamp Counter MSR Model Specific Registers MCE Machine Check Exception CX8 COMPXCHG8B Instruction SEP Fast System Call MTRR Memory Type Range Registers PGE PTE Global Flag MCA Machine Check Architecture CMOV Conditional Move and Compare Instructions FGPAT Page Attribute Table CLFSH CFLUSH instruction DS Debug store ACPI Thermal Monitor and Clock Ctrl MMX MMX instruction set FXSR Fast FP/MMX Streaming SIMD Extensions save/restore SSE Streaming SIMD Extensions instruction set SSE2 SSE2 extensions SS Self Snoop TM Thermal monitor 31 reserved TLB and cache info: b0: unknown TLB/cache descriptor b3: unknown TLB/cache descriptor 02: Instruction TLB: 4MB pages, 4-way set assoc, 2 entries f0: unknown TLB/cache descriptor 7d: unknown TLB/cache descriptor 30: unknown TLB/cache descriptor 04: Data TLB: 4MB pages, 4-way set assoc, 8 entries 2c: unknown TLB/cache descriptor On Lubuntu 14.04.1 live-CD with forcepae: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2 bogomips : 1284.68 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 32 bits virtual power management: uname -a Linux lubuntu 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04.1 LTS Release: 14.04 Codename: trusty cpuid CPU 0: vendor_id = "GenuineIntel" version information (1/eax): processor type = primary processor (0) family = Intel Pentium Pro/II/III/Celeron/Core/Core 2/Atom, AMD Athlon/Duron, Cyrix M2, VIA C3 (6) model = 0xd (13) stepping id = 0x6 (6) extended family = 0x0 (0) extended model = 0x0 (0) (simple synth) = Intel Pentium M (Dothan B1) / Celeron M (Dothan B1), 90nm miscellaneous (1/ebx): process local APIC physical ID = 0x0 (0) cpu count = 0x0 (0) CLFLUSH line size = 0x8 (8) brand index = 0x16 (22) brand id = 0x16 (22): Intel Pentium M, .13um feature information (1/edx): x87 FPU on chip = true virtual-8086 mode enhancement = true debugging extensions = true page size extensions = true time stamp counter = true RDMSR and WRMSR support = true physical address extensions = false machine check exception = true CMPXCHG8B inst. = true APIC on chip = false SYSENTER and SYSEXIT = true memory type range registers = true PTE global bit = true machine check architecture = true conditional move/compare instruction = true page attribute table = true page size extension = false processor serial number = false CLFLUSH instruction = true debug store = true thermal monitor and clock ctrl = true MMX Technology = true FXSAVE/FXRSTOR = true SSE extensions = true SSE2 extensions = true self snoop = true hyper-threading / multi-core supported = false therm. monitor = true IA64 = false pending break event = true feature information (1/ecx): PNI/SSE3: Prescott New Instructions = false PCLMULDQ instruction = false 64-bit debug store = false MONITOR/MWAIT = false CPL-qualified debug store = false VMX: virtual machine extensions = false SMX: safer mode extensions = false Enhanced Intel SpeedStep Technology = true thermal monitor 2 = true SSSE3 extensions = false context ID: adaptive or shared L1 data = false FMA instruction = false CMPXCHG16B instruction = false xTPR disable = false perfmon and debug = false process context identifiers = false direct cache access = false SSE4.1 extensions = false SSE4.2 extensions = false extended xAPIC support = false MOVBE instruction = false POPCNT instruction = false time stamp counter deadline = false AES instruction = false XSAVE/XSTOR states = false OS-enabled XSAVE/XSTOR = false AVX: advanced vector extensions = false F16C half-precision convert instruction = false RDRAND instruction = false hypervisor guest status = false cache and TLB information (2): 0xb0: instruction TLB: 4K, 4-way, 128 entries 0xb3: data TLB: 4K, 4-way, 128 entries 0x02: instruction TLB: 4M pages, 4-way, 2 entries 0xf0: 64 byte prefetching 0x7d: L2 cache: 2M, 8-way, sectored, 64 byte lines 0x30: L1 cache: 32K, 8-way, 64 byte lines 0x04: data TLB: 4M pages, 4-way, 8 entries 0x2c: L1 data cache: 32K, 8-way, 64 byte lines extended feature flags (0x80000001/edx): SYSCALL and SYSRET instructions = false execution disable = false 1-GB large page support = false RDTSCP = false 64-bit extensions technology available = false Intel feature flags (0x80000001/ecx): LAHF/SAHF supported in 64-bit mode = false LZCNT advanced bit manipulation = false 3DNow! PREFETCH/PREFETCHW instructions = false brand = " Intel(R) Pentium(R) M processor 1.50GHz" (multi-processing synth): none (multi-processing method): Intel leaf 1 (synth) = Intel Pentium M (Dothan B1), 90nm

  Read the article

• Metro: Introduction to the WinJS ListView Control

  - by Stephen.Walther

  The goal of this blog entry is to provide a quick introduction to the ListView control – just the bare minimum that you need to know to start using the control. When building Metro style applications using JavaScript, the ListView control is the primary control that you use for displaying lists of items. For example, if you are building a product catalog app, then you can use the ListView control to display the list of products. The ListView control supports several advanced features that I plan to discuss in future blog entries. For example, you can group the items in a ListView, you can create master/details views with a ListView, and you can efficiently work with large sets of items with a ListView. In this blog entry, we’ll keep things simple and focus on displaying a list of products. There are three things that you need to do in order to display a list of items with a ListView: Create a data source Create an Item Template Declare the ListView Creating the ListView Data Source The first step is to create (or retrieve) the data that you want to display with the ListView. In most scenarios, you will want to bind a ListView to a WinJS.Binding.List object. The nice thing about the WinJS.Binding.List object is that it enables you to take a standard JavaScript array and convert the array into something that can be bound to the ListView. It doesn’t matter where the JavaScript array comes from. It could be a static array that you declare or you could retrieve the array as the result of an Ajax call to a remote server. The following JavaScript file – named products.js – contains a list of products which can be bound to a ListView. (function () { "use strict"; var products = new WinJS.Binding.List([ { name: "Milk", price: 2.44 }, { name: "Oranges", price: 1.99 }, { name: "Wine", price: 8.55 }, { name: "Apples", price: 2.44 }, { name: "Steak", price: 1.99 }, { name: "Eggs", price: 2.44 }, { name: "Mushrooms", price: 1.99 }, { name: "Yogurt", price: 2.44 }, { name: "Soup", price: 1.99 }, { name: "Cereal", price: 2.44 }, { name: "Pepsi", price: 1.99 } ]); WinJS.Namespace.define("ListViewDemos", { products: products }); })(); The products variable represents a WinJS.Binding.List object. This object is initialized with a plain-old JavaScript array which represents an array of products. To avoid polluting the global namespace, the code above uses the module pattern and exposes the products using a namespace. The list of products is exposed to the world as ListViewDemos.products. To learn more about the module pattern and namespaces in WinJS, see my earlier blog entry: http://stephenwalther.com/blog/archive/2012/02/22/metro-namespaces-and-modules.aspx Creating the ListView Item Template The ListView control does not know how to render anything. It doesn’t know how you want each list item to appear. To get the ListView control to render something useful, you must create an Item Template. Here’s what our template for rendering an individual product looks like: <div id="productTemplate" data-win-control="WinJS.Binding.Template"> <div class="product"> <span data-win-bind="innerText:name"></span> <span data-win-bind="innerText:price"></span> </div> </div> This template displays the product name and price from the data source. Normally, you will declare your template in the same file as you declare the ListView control. In our case, both the template and ListView are declared in the default.html file. To learn more about templates, see my earlier blog entry: http://stephenwalther.com/blog/archive/2012/02/27/metro-using-templates.aspx Declaring the ListView The final step is to declare the ListView control in a page. Here’s the markup for declaring a ListView: <div data-win-control="WinJS.UI.ListView" data-win-options="{ itemDataSource:ListViewDemos.products.dataSource, itemTemplate:select('#productTemplate') }"> </div> You declare a ListView by adding the data-win-control to an HTML DIV tag. The data-win-options attribute is used to set two properties of the ListView. The ListView is associated with its data source with the itemDataSource property. Notice that the data source is ListViewDemos.products.dataSource and not just ListViewDemos.products. You need to associate the ListView with the dataSoure property. The ListView is associated with its item template with the help of the itemTemplate property. The ID of the item template — #productTemplate – is used to select the template from the page. Here’s what the complete version of the default.html page looks like: <!DOCTYPE html> <html> <head> <meta charset="utf-8"> <title>ListViewDemos</title> <!-- WinJS references --> <link href="//Microsoft.WinJS.0.6/css/ui-dark.css" rel="stylesheet"> <script src="//Microsoft.WinJS.0.6/js/base.js"></script> <script src="//Microsoft.WinJS.0.6/js/ui.js"></script> <!-- ListViewDemos references --> <link href="/css/default.css" rel="stylesheet"> <script src="/js/default.js"></script> <script src="/js/products.js" type="text/javascript"></script> <style type="text/css"> .product { width: 200px; height: 100px; border: white solid 1px; } </style> </head> <body> <div id="productTemplate" data-win-control="WinJS.Binding.Template"> <div class="product"> <span data-win-bind="innerText:name"></span> <span data-win-bind="innerText:price"></span> </div> </div> <div data-win-control="WinJS.UI.ListView" data-win-options="{ itemDataSource:ListViewDemos.products.dataSource, itemTemplate:select('#productTemplate') }"> </div> </body> </html> Notice that the page above includes a reference to the products.js file: <script src=”/js/products.js” type=”text/javascript”></script> The page above also contains a Template control which contains the ListView item template. Finally, the page includes the declaration of the ListView control. Summary The goal of this blog entry was to describe the minimal set of steps which you must complete to use the WinJS ListView control to display a simple list of items. You learned how to create a data source, declare an item template, and declare a ListView control.

  Read the article

• CodePlex Daily Summary for Friday, February 19, 2010

  CodePlex Daily Summary for Friday, February 19, 2010New ProjectsApplication Management Library: Application Management makes your application life easier. It will automatic do memory management, handle and log unhandled exceptions, profiling y...Audio Service - Play Wave Files From Windows Service: This is a windows service that Check a registry key, when the key is updated with a new wave file path the service plays the wave file.Aviamodels: 3d drawing AviamodelsControl of payment proofs program for Greek citizens: This is a program that is used for Greek citizens who want to keep track of their payment proofs.Cover Creator: Cover Creator gives you the possibility to create and print CD covers. Content of CD is taken from http://www.freedb.org/ or can be added/modyfied ...DevBoard: DevBoard is a webbased scrum tool that helps developers/team get a clear overview of the project progress. It's developed in C# and silverlight.Flex AdventureWorks: The is mostly a skunk-works application to help me get acclimated to CodePlex. The long term goal is to integrate a Flex UI with the AdventureWor...GRE Wordlist: An intuitive and customizable word list for GRE aspirants. Developed in Java using a word list similar to Barron's.Indexer: A desktop file Index and Search tool which allows you to choose a list of folders to index, and then search on later. It is based on Lucene.net an...Project Management Office (PMO) for SharePoint: Sample web part for the Code Mastery event in Boston, February 11, 2010.Restart SQL Audit Policy and Job: Resolve SQL 2008 Audit Network Connectivity Issue.Rounded Corners / DIV Container: The RoundedDiv round corners container is a skin-able, CSS compliant UI control. Select which corners should be rounded, collapse and expand the c...Silverlight Google Search Application: The Silverlight Google Search Application uses Google Search API and behaves like Internet Search Application with option to preview desired page i...Weather Forecast Control: MyWeather forecast control pulls up to date weather forecast information from The Weather Channel for your website.New ReleasesApplication Management Library: ApplicationManagement v1.0: First ReleaseAudio Service - Play Wave Files From Windows Service: Audio Service v1.0: This is a working version of the Audio Service. Please use as you need to.AutoMapper: 1.0.1 for Silverlight 3.0 Alpha: AutoMapper for Silverlight 3.0. Features not supported: IDataReader mapping IListSource mapping All other features are supported.Buzz Dot Net: Buzz Dot Net v.1.10219: Buzz Dot Net Library (Parser & Objects) + WPF Example (using MVVM & Threading)Canvas VSDOC Intellisense: V 1.0.0.0a: This release contains two JavaScript files: canvas-utils.js (can be referenced in both runtime and development environment) canvas-vsdoc.js (must ...Control of payment proofs program for Greek citizens: Payment Proofs: source codeCourier: Beta 2: Added Rx Framework support and re-factored how message registration and un-registration works Blog post explaining the updates and re-factoring c...Cover Creator: Initial release: This is initial stable release. For now only in Polish language.Employee Scheduler: Employee Scheduler 2.2: Small Bug found. Small total hour calculation bug. See http://employeescheduler.codeplex.com/WorkItem/View.aspx?WorkItemId=6059 Extract the files...EnhSim: Release v1.9.7.1: Release v1.9.7.1Implemented Dislodged Foreign Object trinket Whispering Fanged Skull now also procs off Flame shock dots You can toggle bloodlust o...Extend SmallBasic: Teaching Extensions v.007: added SimpleSquareTest added Tortoise.Approve() for virtual proctor how to use virtual proctor: change the path in the proctor.txt file (located i...FolderSize: FolderSize.Win32.1.0.1.0: FolderSize.Win32.1.0.1.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...GLB Virtual Player Builder: v0.4.0 Beta: Allows for user to import and use archetypes for building players. The archetypes are contained in the file "archetypes.xml". This file is editab...Google Map WebPart from SharePoint List: GMap Stable Release: GMap Stable ReleaseHenge3D Physics Library for XNA: Henge3D Source (2010-02 R2): Fixed a build error related to an assembly attribute in XBOX 360 builds. Tweaked the controls in the sample when targeting the 360. Reduced the...Indexer: Beta Release 1: Just the initial/rough cut.NukeCS: NukeCS 5.2.3 Source Code: update version to 5.2.3ODOS: ODOS STABLE 1.5.0: Thank you for your patience while we develop this version. Not that much has been added, though. Just doing some sub-conscious stuff to make life...PoshBoard: PoshBoard 3.0 Beta 1: Welcome to the first beta release of PoshBoard 3.0 ! IMPORTANT WARNING : this release is absolutly not feature complete and is error-prone. Okay, ...Restart SQL Audit Policy and Job: Restart SQL 2008 Audit Policy and Job: This folder contains three pieces of source code: Server Audit Status (Started).xml - Import this on-schedule policy into your server's Policy-Ba...SAL- Self Artificial Learning: Artificial Learning 2AQV Working Proof Of Concept: This is the Simulation proof of concept version that comes after the 1aq version. AQ stands for Anwering Questions.SharePoint 2010 Word Automation: SP 2010 Word Automation - Workflow Actions 1.1: This release includes two new custom workflow activities for SharePoint designer Convert Folder Convert Library More information about these new...SharePoint Outlook Connector: Version 1.0.1.1: Exception Logging has been improved.Sharpy: Sharpy 1.2 Alpha: This is the third Sharpy release. A change has been made to allow overriding the master page from the controller. The release contains the single ...Silverlight Google Search Application: SL Google Search App Alpha: This is just a first alpha version of the application, as it looks like when I uploaded it to CodePlex. The application works, requires Silverlight...Starter Kit Mytrip.Mvc.Entity: Mytrip.Mvc.Entity 1.0 RC: EF Membership UserManager FileManager Localization Captcha ClientValidation Theme CrossBrowser VS 2010 RC MVC 2 RC db MSSQL2008thinktecture WSCF.blue: WSCF.blue V1 Update (1.0.6): This release is an update for WSCF.blue V1. Below are the bug fixes made since the V1.0.5 release: The data contract type filter was not including...TS3QueryLib.Net: TS3QueryLib.Net Version 0.18.13.0: Changelog Added overloads to all methods of QueryRunenr class handling permission tasks to allow passing of permission name instead of permissionid...Umbraco CMS: Umbraco 4.1 Beta 2: This is the second beta of Umbraco 4.1. Umbraco 4.1 is more advanced than ever, yet faster, lighter and simpler to use than ever. We, on behalf of...VCC: Latest build, v2.1.30218.0: Automatic drop of latest buildZack's Fiasco - Code Generated DAL: v1.2.4: Enhancements: SQL Server CRUD Stored Procedures added option for USE <db> added option to create or not create INSERT sprocs added option to cr...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)Image Resizer Powertoy Clone for WindowsASP.NETMicrosoft SQL Server Community & SamplesDotNetNuke® Community EditionMost Active ProjectsRawrSharpyDinnerNow.netBlogEngine.NETjQuery Library for SharePoint Web ServicesNB_Store - Free DotNetNuke Ecommerce Catalog Modulepatterns & practices – Enterprise LibraryPHPExcelFacebook Developer ToolkitFluent Ribbon Control Suite

  Read the article

• float right image pushes down text in table below in IE9 [migrated]

  - by Cheers and hth. - Alf

  I'm not a webmaster, not even a web developer, but I'm tasked with adding content to a Wordpress site developed by Someone Else(TM). Here's a page illustrating the problem: http://www.reginedagan.no/program/fiskekonkurranse-i-hovden/. It shows up nice in Firefox: But in IE9 the floated picture pushed down the text in the table below, so that it looks rather awful: I found some related questions on the web, e.g. "CSS: Float right in IE doesn't work!" and "why does a floating DIV mess up table positioning?", and the suggestions there led me to set clear: none on the div around the table, the table itself, and then each individual tr and finally even on each individual td. I also set width="99%" on the table, and tried (but I don't know how correctly) to apply the IE6 quirk fix margin-right: -3px. So here's the content as written in Wordpress, including the unsuccessful attempted fixes: <h1><div style="float: right"><a href="http://www.reginedagan.no/?attachment_id=671"><img src="http://www.reginedagan.no/wp-content/uploads/2012/06/fiskekonkurranse-2011-bilde-3-nedskalert.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" width="200" height="242" class="size-full wp-image-671"/></a></div>Fiskekonkurranse i Hovden!</h1> <div style="background-color: #FAF0F0; clear: none;"><table width="99%" style="clear: none; right-margin: -3px;"> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Dato:</td> <td style="text-align: left; clear: none;">Lørdag 21.juli</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; padding-left: 2em"; clear: none;>/ barn, Flytebrygga</td> <td style="text-align: left; clear: none;">15.00 &ndash; 16.00</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; padding-left: 2em; clear: none;">/ voksne (over 12 år), Moloen</td> <td style="text-align: left; clear: none;">15.00 &ndash; 17.00 </td> </tr> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Sted:</td> <td style="text-align: left; clear: none;">Hovden</td> </tr> <tr style=" clear: none;"> <td style="text-align: left; clear: none;">Pris:</td> <td style="text-align: left; clear: none;">voksen (over 12 år) kr. 50,-, barn kr. 30,-</td> </tr style=" clear: none;"> <tr> <td style="text-align: left; clear: none;">Arrangør:</td> <td style="text-align: left; clear: none;">Hovden Grendelag</td> </tr> </table></div> Velkommen til den årlige Fiskekonkurransen i Hovden lørdag 21. juli! <a href="http://www.reginedagan.no/program/fiskekonkurranse-i-hovden/fiskekonkurranse-2011-bilde-nedskalertjpg/" rel="attachment wp-att-672"><img src="http://www.reginedagan.no/wp-content/uploads/2012/03/fiskekonkurranse-2011-bilde-nedskalertjpg.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" width="400" height="267" class="alignleft size-full wp-image-672" /></a>Det blir stangfiske fra moloen og egen barnekonkurranse fra flytebrygga. Premiering for størst fisk, størst antall kg og flest antall stk. Premiering for barn kl. 16:30 på moloen. Alle premieres. Premiering for voksne på festen om kvelden. Salg av pølser og brus, vafler og kaffe, samt sluker. <div style="clear: left; border: 1px dashed gray; padding: 1em;"> Fest på Hovden samfunnshus kl. 21 &ndash; 02. Musikk: «Mister West», Steinar Aarsnes, Andøya. CC. Salg av øl/vin og snacks. </div> VEL MØTT &mdash; SKITT FISKE! And the resulting HTML served to a browser (only the relevant first part): <div style="float: right;"><a href="http://www.reginedagan.no/?attachment_id=671"><img src="http://www.reginedagan.no/wp-content/uploads/2012/06/fiskekonkurranse-2011-bilde-3-nedskalert.jpg" alt="Fra fiskekonkurransen i 2011" title="Fra fiskekonkurransen i 2011" class="size-full wp-image-671" height="242" width="200"></a></div> <p>Fiskekonkurranse i Hovden!</p></h1> <div style="background-color: rgb(250, 240, 240); clear: none;"> <table style="clear: none;" width="99%"> <tbody><tr style="clear: none;"> <td style="text-align: left; clear: none;">Dato:</td> <td style="text-align: left; clear: none;">Lørdag 21.juli</td> </tr> The able to reproduce the effect with simpler code by setting clear: right on the table. However, I'm unable to reproduce the effect with default styling or with clear: none (as above). So it seems maybe it's something Wordpress does, or maybe it's something the theme thing or whatever it is does – but it's very similar to what others have observed, so there is strong indication that it's also a quirk in IE. Help?

  Read the article

• Static background noise while using new headset Ubuntu 13.04

  - by ThundLayr

  Today I bought a new gaming headset (Gx-Gaming Lychas), and when I tried to record some gameplay-comentary I noticed that there always is a static background noise, I just recorded an example so you guys can listen it (no downloaded needed): http://www47.zippyshare.com/v/65167832/file.html I'm using Kubuntu 13.04 and Kernel version is 3.8.0-19, my laptop is an Acer Travelmate 5760Z, I tried tons of configurations on Alsamixer and none of them made result, I really need to get this working so any kind of help will be very aprecciated. cat /proc/asound/cards: 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xc6400000 irq 44 cat /proc/asound/card0/codec#0 Codec: Conexant CX20588 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x14f1506c Subsystem Id: 0x10250574 Revision Id: 0x100003 No Modem Function Group found Default PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A State of AFG node 0x01: Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS Power: setting=D0, actual=D0 GPIO: io=4, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Headphone Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Headphone Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x4a 0x4a] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Speaker Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Speaker Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x80 0x80] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out Control: name="Beep Playback Volume", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Control: name="Beep Playback Switch", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0 Amp-Out vals: [0x00] Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Control: name="Capture Volume", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Control: name="Capture Switch", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x50 0x50] [0x80 0x80] [0x80 0x80] [0x80 0x80] Converter: stream=4, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Control: name="Mic Boost Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x04 0x04] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a 0x1b* 0x1d 0x1e Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a* 0x1b 0x1d 0x1e Node 0x19 [Pin Complex] wcaps 0x400581: Stereo Control: name="Headphone Jack", index=0, device=0 Pincap 0x0000001c: OUT HP Detect Pin Default 0x04214040: [Jack] HP Out at Ext Right Conn = 1/8, Color = Green DefAssociation = 0x4, Sequence = 0x0 Pin-ctls: 0xc0: OUT HP Unsolicited: tag=01, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1a [Pin Complex] wcaps 0x400481: Stereo Control: name="Internal Mic Phantom Jack", index=0, device=0 Pincap 0x00001324: IN Detect Vref caps: HIZ 50 80 Pin Default 0x90a70130: [Fixed] Mic at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1b [Pin Complex] wcaps 0x400581: Stereo Control: name="Mic Jack", index=0, device=0 Pincap 0x00011334: IN OUT EAPD Detect Vref caps: HIZ 50 80 EAPD 0x0: Pin Default 0x04a19020: [Jack] Mic at Ext Right Conn = 1/8, Color = Pink DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=02, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1c [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00000014: OUT Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1d [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00010034: IN OUT EAPD Detect EAPD 0x0: Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1e [Pin Complex] wcaps 0x400481: Stereo Pincap 0x00000024: IN Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Control: name="Speaker Phantom Jack", index=0, device=0 Pincap 0x00000010: OUT Pin Default 0x92170110: [Fixed] Speaker at Int Front Conn = Analog, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11* Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x12 Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x21 Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x00 0x00] Pincap 0x00000020: IN Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11 Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

  Read the article

• Metro: Introduction to the WinJS ListView Control

  - by Stephen.Walther

  The goal of this blog entry is to provide a quick introduction to the ListView control – just the bare minimum that you need to know to start using the control. When building Metro style applications using JavaScript, the ListView control is the primary control that you use for displaying lists of items. For example, if you are building a product catalog app, then you can use the ListView control to display the list of products. The ListView control supports several advanced features that I plan to discuss in future blog entries. For example, you can group the items in a ListView, you can create master/details views with a ListView, and you can efficiently work with large sets of items with a ListView. In this blog entry, we’ll keep things simple and focus on displaying a list of products. There are three things that you need to do in order to display a list of items with a ListView: Create a data source Create an Item Template Declare the ListView Creating the ListView Data Source The first step is to create (or retrieve) the data that you want to display with the ListView. In most scenarios, you will want to bind a ListView to a WinJS.Binding.List object. The nice thing about the WinJS.Binding.List object is that it enables you to take a standard JavaScript array and convert the array into something that can be bound to the ListView. It doesn’t matter where the JavaScript array comes from. It could be a static array that you declare or you could retrieve the array as the result of an Ajax call to a remote server. The following JavaScript file – named products.js – contains a list of products which can be bound to a ListView. (function () { "use strict"; var products = new WinJS.Binding.List([ { name: "Milk", price: 2.44 }, { name: "Oranges", price: 1.99 }, { name: "Wine", price: 8.55 }, { name: "Apples", price: 2.44 }, { name: "Steak", price: 1.99 }, { name: "Eggs", price: 2.44 }, { name: "Mushrooms", price: 1.99 }, { name: "Yogurt", price: 2.44 }, { name: "Soup", price: 1.99 }, { name: "Cereal", price: 2.44 }, { name: "Pepsi", price: 1.99 } ]); WinJS.Namespace.define("ListViewDemos", { products: products }); })(); The products variable represents a WinJS.Binding.List object. This object is initialized with a plain-old JavaScript array which represents an array of products. To avoid polluting the global namespace, the code above uses the module pattern and exposes the products using a namespace. The list of products is exposed to the world as ListViewDemos.products. To learn more about the module pattern and namespaces in WinJS, see my earlier blog entry: http://stephenwalther.com/blog/archive/2012/02/22/metro-namespaces-and-modules.aspx Creating the ListView Item Template The ListView control does not know how to render anything. It doesn’t know how you want each list item to appear. To get the ListView control to render something useful, you must create an Item Template. Here’s what our template for rendering an individual product looks like: <div id="productTemplate" data-win-control="WinJS.Binding.Template"> <div class="product"> <span data-win-bind="innerText:name"></span> <span data-win-bind="innerText:price"></span> </div> </div> This template displays the product name and price from the data source. Normally, you will declare your template in the same file as you declare the ListView control. In our case, both the template and ListView are declared in the default.html file. To learn more about templates, see my earlier blog entry: http://stephenwalther.com/blog/archive/2012/02/27/metro-using-templates.aspx Declaring the ListView The final step is to declare the ListView control in a page. Here’s the markup for declaring a ListView: <div data-win-control="WinJS.UI.ListView" data-win-options="{ itemDataSource:ListViewDemos.products.dataSource, itemTemplate:select('#productTemplate') }"> </div> You declare a ListView by adding the data-win-control to an HTML DIV tag. The data-win-options attribute is used to set two properties of the ListView. The ListView is associated with its data source with the itemDataSource property. Notice that the data source is ListViewDemos.products.dataSource and not just ListViewDemos.products. You need to associate the ListView with the dataSoure property. The ListView is associated with its item template with the help of the itemTemplate property. The ID of the item template — #productTemplate – is used to select the template from the page. Here’s what the complete version of the default.html page looks like: <!DOCTYPE html> <html> <head> <meta charset="utf-8"> <title>ListViewDemos</title> <!-- WinJS references --> <link href="//Microsoft.WinJS.0.6/css/ui-dark.css" rel="stylesheet"> <script src="//Microsoft.WinJS.0.6/js/base.js"></script> <script src="//Microsoft.WinJS.0.6/js/ui.js"></script> <!-- ListViewDemos references --> <link href="/css/default.css" rel="stylesheet"> <script src="/js/default.js"></script> <script src="/js/products.js" type="text/javascript"></script> <style type="text/css"> .product { width: 200px; height: 100px; border: white solid 1px; } </style> </head> <body> <div id="productTemplate" data-win-control="WinJS.Binding.Template"> <div class="product"> <span data-win-bind="innerText:name"></span> <span data-win-bind="innerText:price"></span> </div> </div> <div data-win-control="WinJS.UI.ListView" data-win-options="{ itemDataSource:ListViewDemos.products.dataSource, itemTemplate:select('#productTemplate') }"> </div> </body> </html> Notice that the page above includes a reference to the products.js file: <script src=”/js/products.js” type=”text/javascript”></script> The page above also contains a Template control which contains the ListView item template. Finally, the page includes the declaration of the ListView control. Summary The goal of this blog entry was to describe the minimal set of steps which you must complete to use the WinJS ListView control to display a simple list of items. You learned how to create a data source, declare an item template, and declare a ListView control.

  Read the article

• CodePlex Daily Summary for Wednesday, May 19, 2010

  CodePlex Daily Summary for Wednesday, May 19, 2010New Projects3FD - Framework For Fast Development: This is a C++ framework that provides a solid error handling structure, garbage collection, multi-threading and portability between compilers. The ...ali test project: test projectAttribute Builder: The Attribute Builder builds an attribute from a lambda expression because it can.BDK0008: it is a food lovers websitecgdigest: cg digest template for non-profit orgCokmez: Bilmuh cokmez duyuru sistemiDot Game: It is a dot game that our Bangladeshi people used to play at their childhood time and their last time when they are poor for working.ESRI Javascript .NET Integration: Visual Studio project that shows how to integrate the Esri Javascript API with .NET Exchange 2010 RBAC Editor (RBAC GUI): Exchange 2010 RBAC Editor (RBAC GUI) Developed in C# and using Powershell behind the scenes RBAC tool to simplfy RBAC administrationFile Validator (Validador de Archivos): Componente que permite realizar la validación de archivos (txt, imagenes, PDF, etc) actualmente solo tiene implementado la parte de los txt, permit...Grip 09 Lab4: GripjPageFlipper: This is a wonderful implementation of page flipper entirely based on HTML 5 <canvas> tag. It means that it can work in any browser that supports HT...Main project: Index bird families and associated species. Malware Analysis and Can Handler: MACH is a tool to organize and catalog your malware analysis canned responses, and to track the topic response lifecycle for forum experts.Perf Web: Performance team web sitePiPiBugNet: PiPiBugNet是一套全新的开源Bug管理系统。 PiPiBugNet代码基于ASP.NET 2.0平台开发，编程语言为C#。 PiPiBugNet界面基于Ext JS设计，提供了极佳的用户体验。RemoteDesktop: integrated remote console, desktop and chat utilityRuneScape emulation done right.: RuneScape emulator.Sandkasten: SandkastenSilverlight Metro Theme: Metro Theme for Silverlight.Silverlight Stereoscopy: Stereoscopy with Silverlight.Twitivia: Twitivia is an online trivia service that runs through twitter and is being used as an example set of projects. C#, MVC, Windows Services, Linq ...XPool: A simple school project.New ReleasesDot Game: 'Dot Game' first release: Dot Game first release This is the 'Dot Game' first release.DotNetNuke® Store: 02.01.35: What's New in this release? Bugs corrected: - Fixed a resource for the header in the Category list of the Store Admin module. - Added several test...ESRI Javascript .NET Integration: Map search results in a DataView: Visual Studio 2010 example showing how to pass Map results back to ASP.NET for use in a DataView.Exchange 2010 RBAC Editor (RBAC GUI): RBAC Editor: This binary is still beta (0.0.9.1) but in most case it's very stableExtending C# editor - Outlining, classification: first revision: a couple of bug has been eliminated, performance improvementFloe IRC Client: Floe IRC Client 2010-05 R6: Corrected bug where text would be unexpectedly copied to the clipboard.Floe IRC Client: Floe IRC Client 2010-05 R7: - Fixed bug where text would show up in a query window with someone if they said something on a channel that you are both present on.Free Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts v3.0.9 GA released: Hi, Today we have released the final version of Visifire v3.0.9 which contains the following enhancements: * Two new properties ActualAxisMin...Free Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts v3.5.2 GA Released: Hi, Today we have released the final version of Visifire v3.5.2 which contains the following enhancements: Two new properties ActualAxisMinimum a...HB Batch Encoder Mk 2: HB Batch Encoder Mk2 v1.02: Added .mov support.jPageFlipper: jPageFlipper 0.9: This is an initial community preview of jPageFlipper. It's not ready for production usage but has almost all functionality implemented.linq.js - LINQ for JavaScript: ver 2.1.0.0: Add Class Dictionary Lookup Grouping OrderedEnumerable Add Method ToDictionary MemoizeAll Share Let Add Overload ...Microsoft Research Biology Extension for Excel: MSR Biology Extension for Excel - M9: M9 Release includes the following updates to the previous release: > Import / Export support from Excel for multiple file formats > Bug fixes and ...Nifty CSharp Tools: Event Watcher: Event Watcher!Paint.NET Bulk Image Processor: Paint.NET Bulk Image Processor v1.0: This is the initial release of the Paint.NET Bulk Image processor plugin. All feedback is welcome.PiPiBugNet: PiPiBugNet架构设计: PiPiBugNet架构设计，未包含功能实现RuneScape emulation done right.: rc0: Release cantidate 0.Rx Contrib: V1.6: Adding CCR queue as adapter for the ReactiveQueue credits goes to Yuval Mazor http://blogs.microsoft.co.il/blogs/yuvmaz/Silverlight Metro Theme: Silverlight Metro Theme Alpha 1: Silverlight Metro Theme Alpha 1Silverlight Stereoscopy: Silverlight Stereoscopy Alpha 1: Silverlight Stereoscopy Alpha 20100518Stratosphere: Stratosphere 1.0.6.0: Introduced support for batch put Introduced Support for conditional updates and consistent read Added support for select conditions Brought t...VCC: Latest build, v2.1.30518.0: Automatic drop of latest buildVideo Downloader: Example Program - 1.1: Example Program showing the features of the DLL and what can be achieved using it. For DLL Version 1.1.Video Downloader: Version 1.1: Version 1.1 See Home Page for usage and more information regarding new features. Please remember changes at You-Tube can prevent this software from...WatchersNET.TagCloud: WatchersNET.TagCloud 01.06.00: Whats New New Tag Mode: Show Tags from Ventrian.com NewsArticles Module New Tag Mode: Show Tags from Ventrian.com SimpleGallery Module Hyperlin...Windows Double Explorer: WDE v0.4: -optimization -switch to new vst2010 -viewer close now by pressing escape -reorder tabs -send selected fullname or shortnames via email (eye button...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryMicrosoft SQL Server Community & SamplesPHPExcelASP.NETMost Active Projectspatterns & practices – Enterprise LibraryRawrPHPExcelGMap.NET - Great Maps for Windows Forms & PresentationCustomer Portal Accelerator for Microsoft Dynamics CRMBlogEngine.NETWindows Azure Command-line Tools for PHP DevelopersCassiniDev - Cassini 3.5/4.0 Developers EditionSQL Server PowerShell ExtensionsFluent Ribbon Control Suite

  Read the article

• How you can extend Tasklists in Fusion Applications

  - by Elie Wazen

  In this post we describe the process of modifying and extending a Tasklist available in the Regional Area of a Fusion Applications UI Shell. This is particularly useful to Customers who would like to expose Setup Tasks (generally available in the Fusion Setup Manager application) in the various functional pillars workareas. Oracle Composer, the tool used to implement such extensions allows changes to be made at runtime. The example provided in this document is for an Oracle Fusion Financials page. Let us examine the case of a customer role who requires access to both, a workarea and its associated functional tasks, and to an FSM (setup) task.  Both of these tasks represent ADF Taskflows but each is accessible from a different page.  We will show how an FSM task is added to a Functional tasklist and made accessible to a user from within a single workarea, eliminating the need to navigate between the FSM application and the Functional workarea where transactions are conducted. In general, tasks in Fusion Applications are grouped in two ways: Setup tasks are grouped in tasklists available to implementers in the Functional Setup Manager (FSM). These Tasks are accessed by implementation users and in general do not represent daily operational tasks that fit into a functional business process and were consequently included in the FSM application. For these tasks, the primary organizing principle is precedence between tasks. If task "Manage Suppliers" has prerequisites, those tasks must precede it in a tasklist. Task Lists are organized to efficiently implement an offering. Tasks frequently performed as part of business process flows are made available as links in the tasklist of their corresponding menu workarea. The primary organizing principle in the menu and task pane entries is to group tasks that are generally accessed together. Customizing a tasklist thus becomes required for business scenarios where a task packaged under FSM as a setup task, is for a particular customer a regular maintenance task that is accessed for record updates or creation as part of normal operational activities and where the frequency of this access merits the inclusion of that task in the related operational tasklist A user with the role of maintaining Journals in General Ledger is also responsible for maintaining Chart of Accounts Mappings.  In the Fusion Financials Product Family, Manage Journals is a task available from within the Journals Menu whereas Chart of Accounts Mapping is available via FSM under the Define Chart of Accounts tasklist Figure 1. The Manage Chart of Accounts Mapping Task in FSM Figure 2. The Manage Journals Task in the Task Pane of the Journals Workarea Our goal is to simplify cross task navigation and allow the user to access both tasks from a single tasklist on a single page without having to navigate to FSM for the Mapping task and to the Journals workarea for the Manage task. To accomplish that, we use Oracle Composer to customize  the Journals tasklist by adding to it the Mapping task. Identify the Taskflow name and path of the FSM Task The first step in our process is to identify the underlying taskflow for the Manage Chart of Accounts Mappings task. We select to Setup and Maintenance from the Navigator to launch the FSM Application, and we query the task from Manage Tasklists and Tasks Figure 3. Task Details including Taskflow path The Manage Chart of Accounts Mapping Task Taskflow is: /WEB-INF/oracle/apps/financials/generalLedger/sharedSetup/coaMappings/ui/flow /CoaMappingsMainAreaFlow.xml#CoaMappingsMainAreaFlow We copy that value and use it later as a parameter to our new task in the customized Journals Tasklist. Customize the Journals Page A user with Administration privileges can start the run time customization directly from the Administration Menu of the Global Area.  This customization is done at the Site level and once implemented becomes available to all users with access to the Journals Workarea. Figure 4.  Customization Menu The Oracle Composer Window is displayed in the same browser and the Hierarchy of the page component is displayed and available for modification. Figure 5.  Oracle Composer In the composer Window select the PanelFormLayout node and click on the Edit Button.  Note that the selected component is simultaneously highlighted in the lower pane in the browser. In the Properties popup window, select the Tasks List and Task Properties Tab, where the user finds the hierarchy of the Tasklist and is able to Edit nodes or create new ones. src="https://blogs.oracle.com/FunctionalArchitecture/resource/TL5.jpg" Figure 6.  The Tasklist in edit mode Add a Child Task to the Tasklist In the Edit Window the user will now create a child node at the desired level in the hierarchy by selecting the immediate parent node and clicking on the insert node button.  This process requires four values to be set as described in Table 1 below. Parameter Value How to Determine the Value Focus View Id /JournalEntryPage This is the Focus View ID of the UI Shell where the Tasklist we want to customize is.  A simple way to determine this value is to copy it from any of the Standard tasks on the Tasklist Label COA Mapping This is the Display name of the Task as it will appear in the Tasklist Task Type dynamicMain If the value is dynamicMain, the page contains a new link in the Regional Area. When you click the link, a new tab with the loaded task opens Taskflowid /WEB-INF/oracle/apps/financials/generalLedger/sharedSetup/ coaMappings/ui/flow/ CoaMappingsMainAreaFlow.xml#CoaMappingsMainAreaFlow This is the Taskflow path we retrieved from the Task Definition in FSM earlier in the process Table 1.  Parameters and Values for the Task to be added to the customized Tasklist Figure 7.   The parameters window of the newly added Task   Access the FSM Task from the Journals Workarea Once the FSM task is added and its parameters defined, the user saves the record, closes the Composer making the new task immediately available to users with access to the Journals workarea (Refer to Figure 8 below). Figure 8.   The COA Mapping Task is now visible and can be invoked from the Journals Workarea   Additional Considerations If a Task Flow is part of a product that is deployed on the same app server as the Tasklist workarea then that task flow can be added to a customized tasklist in that workarea. Otherwise that task flow can be invoked from its parent product’s workarea tasklist by selecting that workarea from the Navigator menu. For Example The following Taskflows  belong respectively to the Subledger Accounting, and to the General Ledger Products.  /WEB-INF/oracle/apps/financials/subledgerAccounting/accountingMethodSetup/mappingSets/ui/flow/MappingSetFlow.xml#MappingSetFlow /WEB-INF/oracle/apps/financials/generalLedger/sharedSetup/coaMappings/ui/flow/CoaMappingsMainAreaFlow.xml#CoaMappingsMainAreaFlow Since both the Subledger Accounting and General Ledger products are part of the LedgerApp J2EE Applicaton and are both deployed on the General Ledger Cluster Server (Figure 8 below), the user can add both of the above taskflows to the  tasklist in the  /JournalEntryPage FocusVIewID Workarea. Note:  both FSM Taskflows and Functional Taskflows can be added to the Tasklists as described in this document Figure 8.   The Topology of the Fusion Financials Product Family. Note that SubLedger Accounting and General Ledger are both deployed on the Ledger App Conclusion In this document we have shown how an administrative user can edit the Tasklist in the Regional Area of a Fusion Apps page using Oracle Composer. This is useful for cases where tasks packaged in different workareas are frequently accessed by the same user. By making these tasks available from the same page, we minimize the number of steps in the navigation the user has to do to perform their transactions and queries in Fusion Apps.  The example explained above showed that tasks classified as Setup tasks, meaning made accessible to implementation users from the FSM module can be added to the workarea of their respective Fusion application. This eliminates the need to navigate to FSM to access tasks that are both setup and regular maintenance tasks. References Oracle Fusion Applications Extensibility Guide 11g Release 1 (11.1.1.5) Part Number E16691-02 (Section 3.2) Oracle Fusion Applications Developer's Guide 11g Release 1 (11.1.4) Part Number E15524-05

  Read the article

• How to solve exception_priv _instruction exception while running destop project? [on hold]

  - by Haritha

  While running desktop project im getting exception_priv _instruction how to solve this??? while running this page is coming # # A fatal error has been detected by the Java Runtime Environment: # # EXCEPTION_PRIV_INSTRUCTION (0xc0000096) at pc=0x02f5a92b, pid=3012, tid=3104 # # JRE version: 7.0-b147 # Java VM: Java HotSpot(TM) Client VM (21.0-b17 mixed mode, sharing windows-x86 ) # Problematic frame: # C 0x02f5a92b # # Failed to write core dump. Minidumps are not enabled by default on client versions of Windows # # If you would like to submit a bug report, please visit: # http://bugreport.sun.com/bugreport/crash.jsp # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # --------------- T H R E A D --------------- Current thread (0x02f5a800): JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] siginfo: ExceptionCode=0xc0000096 Registers: EAX=0x000df4f0, EBX=0x32afc180, ECX=0x000df4f0, EDX=0x00000020 ESP=0x0773f768, EBP=0x0773f790, ESI=0x32afc180, EDI=0x02f5a800 EIP=0x02f5a92b, EFLAGS=0x00010206 Top of Stack: (sp=0x0773f768) 0x0773f768: 02bd429c 02bd429c 0773f770 32afc180 0x0773f778: 0773f7b8 32b022c8 00000000 32afc180 0x0773f788: 00000000 0773f7a0 0773f7dc 00943187 0x0773f798: 229ec1c0 00948839 69081736 00000000 0x0773f7a8: 089b0048 00000000 00000014 00001406 0x0773f7b8: 00000002 0773f7bc 32afbeb0 0773f7f8 0x0773f7c8: 32b022c8 00000000 32afbf00 0773f7a0 0x0773f7d8: 0773f7f0 0773f81c 00943187 69081736 Instructions: (pc=0x02f5a92b) 0x02f5a90b: 00 43 00 00 00 00 f0 bc 02 e8 00 e9 22 40 f7 73 0x02f5a91b: 07 85 a5 94 00 90 f7 73 07 50 cc a0 6d d8 49 c0 0x02f5a92b: 6d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x02f5a93b: 00 00 00 00 00 00 00 00 00 08 80 3d 37 00 00 00 Register to memory mapping: EAX=0x000df4f0 is an unknown value EBX=0x32afc180 is an oop {method} - klass: {other class} ECX=0x000df4f0 is an unknown value EDX=0x00000020 is an unknown value ESP=0x0773f768 is pointing into the stack for thread: 0x02f5a800 EBP=0x0773f790 is pointing into the stack for thread: 0x02f5a800 ESI=0x32afc180 is an oop {method} - klass: {other class} EDI=0x02f5a800 is a thread Stack: [0x076f0000,0x07740000], sp=0x0773f768, free space=317k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C 0x02f5a92b j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub V [jvm.dll+0x122c7e] V [jvm.dll+0x1c9c0e] V [jvm.dll+0x122e73] V [jvm.dll+0x122ed7] V [jvm.dll+0xccd1f] V [jvm.dll+0x14433f] V [jvm.dll+0x171549] C [msvcr100.dll+0x5c6de] endthreadex+0x3a C [msvcr100.dll+0x5c788] endthreadex+0xe4 C [kernel32.dll+0xb713] GetModuleFileNameA+0x1b4 Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j org.lwjgl.opengl.GL11.nglVertexPointer(IIIJJ)V+0 j org.lwjgl.opengl.GL11.glVertexPointer(IILjava/nio/FloatBuffer;)V+48 j com.badlogic.gdx.backends.lwjgl.LwjglGL10.glVertexPointer(IIILjava/nio/Buffer;)V+53 j com.badlogic.gdx.graphics.glutils.VertexArray.bind()V+149 j com.badlogic.gdx.graphics.Mesh.bind()V+25 j com.badlogic.gdx.graphics.Mesh.render(IIIZ)V+32 j com.badlogic.gdx.graphics.Mesh.render(III)V+8 j com.badlogic.gdx.graphics.g2d.SpriteBatch.flush()V+197 j com.badlogic.gdx.graphics.g2d.SpriteBatch.switchTexture(Lcom/badlogic/gdx/graphics/Texture;)V+1 j com.badlogic.gdx.graphics.g2d.SpriteBatch.draw(Lcom/badlogic/gdx/graphics/Texture;FFFF)V+33 j sevenseas.game.WorldRenderer.drawBob()V+54 j sevenseas.game.WorldRenderer.render()V+12 j sevenseas.game.GameClass.render(F)V+38 j com.badlogic.gdx.Game.render()V+19 j com.badlogic.gdx.backends.lwjgl.LwjglApplication.mainLoop()V+642 j com.badlogic.gdx.backends.lwjgl.LwjglApplication$1.run()V+27 v ~StubRoutines::call_stub --------------- P R O C E S S --------------- Java Threads: ( => current thread ) 0x003d6c00 JavaThread "DestroyJavaVM" [_thread_blocked, id=3240, stack(0x008c0000,0x00910000)] =>0x02f5a800 JavaThread "LWJGL Application" [_thread_in_native, id=3104, stack(0x076f0000,0x07740000)] 0x02bcf000 JavaThread "Service Thread" daemon [_thread_blocked, id=2612, stack(0x02e00000,0x02e50000)] 0x02bc1000 JavaThread "C1 CompilerThread0" daemon [_thread_blocked, id=2776, stack(0x02db0000,0x02e00000)] 0x02bbf400 JavaThread "Attach Listener" daemon [_thread_blocked, id=2448, stack(0x02d60000,0x02db0000)] 0x02bbe000 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=1764, stack(0x02d10000,0x02d60000)] 0x02bb8000 JavaThread "Finalizer" daemon [_thread_blocked, id=3864, stack(0x02cc0000,0x02d10000)] 0x02bb3400 JavaThread "Reference Handler" daemon [_thread_blocked, id=2424, stack(0x02c70000,0x02cc0000)] Other Threads: 0x02bb1800 VMThread [stack: 0x02c20000,0x02c70000] [id=3076] 0x02bd1000 WatcherThread [stack: 0x02e50000,0x02ea0000] [id=3276] VM state:not at safepoint (normal execution) VM Mutex/Monitor currently owned by a thread: None Heap def new generation total 4928K, used 2571K [0x229c0000, 0x22f10000, 0x27f10000) eden space 4416K, 46% used [0x229c0000, 0x22bc2e38, 0x22e10000) from space 512K, 100% used [0x22e90000, 0x22f10000, 0x22f10000) to space 512K, 0% used [0x22e10000, 0x22e10000, 0x22e90000) tenured generation total 10944K, used 634K [0x27f10000, 0x289c0000, 0x329c0000) the space 10944K, 5% used [0x27f10000, 0x27faea60, 0x27faec00, 0x289c0000) compacting perm gen total 12288K, used 1655K [0x329c0000, 0x335c0000, 0x369c0000) the space 12288K, 13% used [0x329c0000, 0x32b5dc58, 0x32b5de00, 0x335c0000) ro space 10240K, 42% used [0x369c0000, 0x36dfc660, 0x36dfc800, 0x373c0000) rw space 12288K, 53% used [0x373c0000, 0x37a38180, 0x37a38200, 0x37fc0000) Code Cache [0x00940000, 0x009d8000, 0x02940000) total_blobs=305 nmethods=80 adapters=158 free_code_cache=32183Kb largest_free_block=32955904 Dynamic libraries: 0x00400000 - 0x0042f000 C:\Program Files\Java\jre7\bin\javaw.exe 0x7c900000 - 0x7c9af000 C:\WINDOWS\system32\ntdll.dll 0x7c800000 - 0x7c8f6000 C:\WINDOWS\system32\kernel32.dll 0x77dd0000 - 0x77e6b000 C:\WINDOWS\system32\ADVAPI32.dll 0x77e70000 - 0x77f02000 C:\WINDOWS\system32\RPCRT4.dll 0x77fe0000 - 0x77ff1000 C:\WINDOWS\system32\Secur32.dll 0x7e410000 - 0x7e4a1000 C:\WINDOWS\system32\USER32.dll 0x77f10000 - 0x77f59000 C:\WINDOWS\system32\GDI32.dll 0x773d0000 - 0x774d3000 C:\WINDOWS\WinSxS\x86_Microsoft.Windows.Common-Controls_6595b64144ccf1df_6.0.2600.5512_x-ww_35d4ce83\COMCTL32.dll 0x77c10000 - 0x77c68000 C:\WINDOWS\system32\msvcrt.dll 0x77f60000 - 0x77fd6000 C:\WINDOWS\system32\SHLWAPI.dll 0x76390000 - 0x763ad000 C:\WINDOWS\system32\IMM32.DLL 0x629c0000 - 0x629c9000 C:\WINDOWS\system32\LPK.DLL 0x74d90000 - 0x74dfb000 C:\WINDOWS\system32\USP10.dll 0x78aa0000 - 0x78b5e000 C:\Program Files\Java\jre7\bin\msvcr100.dll 0x6d940000 - 0x6dc61000 C:\Program Files\Java\jre7\bin\client\jvm.dll 0x71ad0000 - 0x71ad9000 C:\WINDOWS\system32\WSOCK32.dll 0x71ab0000 - 0x71ac7000 C:\WINDOWS\system32\WS2_32.dll 0x71aa0000 - 0x71aa8000 C:\WINDOWS\system32\WS2HELP.dll 0x76b40000 - 0x76b6d000 C:\WINDOWS\system32\WINMM.dll 0x76bf0000 - 0x76bfb000 C:\WINDOWS\system32\PSAPI.DLL 0x6d8d0000 - 0x6d8dc000 C:\Program Files\Java\jre7\bin\verify.dll 0x6d370000 - 0x6d390000 C:\Program Files\Java\jre7\bin\java.dll 0x6d920000 - 0x6d933000 C:\Program Files\Java\jre7\bin\zip.dll 0x6cec0000 - 0x6cf42000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\37fe1abc\gdx.dll 0x10000000 - 0x1004c000 C:\Documents and Settings\7stl0225\Local Settings\Temp\libgdx7stl0225\52d76f2b\lwjgl.dll 0x5ed00000 - 0x5edcc000 C:\WINDOWS\system32\OPENGL32.dll 0x68b20000 - 0x68b40000 C:\WINDOWS\system32\GLU32.dll 0x73760000 - 0x737ab000 C:\WINDOWS\system32\DDRAW.dll 0x73bc0000 - 0x73bc6000 C:\WINDOWS\system32\DCIMAN32.dll 0x77c00000 - 0x77c08000 C:\WINDOWS\system32\VERSION.dll 0x070b0000 - 0x07115000 C:\DOCUME~1\7stl0225\LOCALS~1\Temp\libgdx7stl0225\52d76f2b\OpenAL32.dll 0x7c9c0000 - 0x7d1d7000 C:\WINDOWS\system32\SHELL32.dll 0x774e0000 - 0x7761d000 C:\WINDOWS\system32\ole32.dll 0x5ad70000 - 0x5ada8000 C:\WINDOWS\system32\uxtheme.dll 0x76fd0000 - 0x7704f000 C:\WINDOWS\system32\CLBCATQ.DLL 0x77050000 - 0x77115000 C:\WINDOWS\system32\COMRes.dll 0x77120000 - 0x771ab000 C:\WINDOWS\system32\OLEAUT32.dll 0x73f10000 - 0x73f6c000 C:\WINDOWS\system32\dsound.dll 0x76c30000 - 0x76c5e000 C:\WINDOWS\system32\WINTRUST.dll 0x77a80000 - 0x77b15000 C:\WINDOWS\system32\CRYPT32.dll 0x77b20000 - 0x77b32000 C:\WINDOWS\system32\MSASN1.dll 0x76c90000 - 0x76cb8000 C:\WINDOWS\system32\IMAGEHLP.dll 0x72d20000 - 0x72d29000 C:\WINDOWS\system32\wdmaud.drv 0x72d10000 - 0x72d18000 C:\WINDOWS\system32\msacm32.drv 0x77be0000 - 0x77bf5000 C:\WINDOWS\system32\MSACM32.dll 0x77bd0000 - 0x77bd7000 C:\WINDOWS\system32\midimap.dll 0x73ee0000 - 0x73ee4000 C:\WINDOWS\system32\KsUser.dll 0x755c0000 - 0x755ee000 C:\WINDOWS\system32\msctfime.ime 0x69000000 - 0x691a9000 C:\WINDOWS\system32\sisgl.dll 0x73b30000 - 0x73b45000 C:\WINDOWS\system32\mscms.dll 0x73000000 - 0x73026000 C:\WINDOWS\system32\WINSPOOL.DRV 0x66e90000 - 0x66ed1000 C:\WINDOWS\system32\icm32.dll 0x07760000 - 0x0778d000 C:\Program Files\WordWeb\WHook.dll 0x74c80000 - 0x74cac000 C:\WINDOWS\system32\OLEACC.dll 0x76080000 - 0x760e5000 C:\WINDOWS\system32\MSVCP60.dll VM Arguments: jvm_args: -Dfile.encoding=Cp1252 java_command: sevenseas.game.MainDesktop Launcher Type: SUN_STANDARD Environment Variables: PATH=C:/Program Files/Java/jre7/bin/client;C:/Program Files/Java/jre7/bin;C:/Program Files/Java/jre7/lib/i386;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\Java\jdk1.7.0\bin;C:\eclipse; USERNAME=7stl0225 OS=Windows_NT PROCESSOR_IDENTIFIER=x86 Family 15 Model 4 Stepping 1, GenuineIntel --------------- S Y S T E M --------------- OS: Windows XP Build 2600 Service Pack 3 CPU:total 1 (1 cores per cpu, 1 threads per core) family 15 model 4 stepping 1, cmov, cx8, fxsr, mmx, sse, sse2, sse3 Memory: 4k page, physical 2031088k(939252k free), swap 3969920k(3011396k free) vm_info: Java HotSpot(TM) Client VM (21.0-b17) for windows-x86 JRE (1.7.0-b147), built on Jun 27 2011 02:25:52 by "java_re" with unknown MS VC++:1600 time: Sat Oct 26 12:35:14 2013 elapsed time: 0 seconds

  Read the article

• SQL SERVER – Thinking about Deprecated, Discontinued Features and Breaking Changes while Upgrading to SQL Server 2012 – Guest Post by Nakul Vachhrajani

  - by pinaldave

  Nakul Vachhrajani is a Technical Specialist and systems development professional with iGATE having a total IT experience of more than 7 years. Nakul is an active blogger with BeyondRelational.com (150+ blogs), and can also be found on forums at SQLServerCentral and BeyondRelational.com. Nakul has also been a guest columnist for SQLAuthority.com and SQLServerCentral.com. Nakul presented a webcast on the “Underappreciated Features of Microsoft SQL Server” at the Microsoft Virtual Tech Days Exclusive Webcast series (May 02-06, 2011) on May 06, 2011. He is also the author of a research paper on Database upgrade methodologies, which was published in a CSI journal, published nationwide. In addition to his passion about SQL Server, Nakul also contributes to the academia out of personal interest. He visits various colleges and universities as an external faculty to judge project activities being carried out by the students. Disclaimer: The opinions expressed herein are his own personal opinions and do not represent his employer’s view in anyway. Blog | LinkedIn | Twitter | Google+ Let us hear the thoughts of Nakul in first person - Those who have been following my blogs would be aware that I am recently running a series on the database engine features that have been deprecated in Microsoft SQL Server 2012. Based on the response that I have received, I was quite surprised to know that most of the audience found these to be breaking changes, when in fact, they were not! It was then that I decided to write a little piece on how to plan your database upgrade such that it works with the next version of Microsoft SQL Server. Please note that the recommendations made in this article are high-level markers and are intended to help you think over the specific steps that you would need to take to upgrade your database. Refer the documentation – Understand the terms Change is the only constant in this world. Therefore, whenever customer requirements, newer architectures and designs require software vendors to make a change to the keywords, functions, etc; they ensure that they provide their end users sufficient time to migrate over to the new standards before dropping off the old ones. Microsoft does that too with it’s Microsoft SQL Server product. Whenever a new SQL Server release is announced, it comes with a list of the following features: Breaking changes These are changes that would break your currently running applications, scripts or functionalities that are based on earlier version of Microsoft SQL Server These are mostly features whose behavior has been changed keeping in mind the newer architectures and designs Lesson: These are the changes that you need to be most worried about! Discontinued features These features are no longer available in the associated version of Microsoft SQL Server These features used to be “deprecated” in the prior release Lesson: Without these changes, your database would not be compliant/may not work with the version of Microsoft SQL Server under consideration Deprecated features These features are those that are still available in the current version of Microsoft SQL Server, but are scheduled for removal in a future version. These may be removed in either the next version or any other future version of Microsoft SQL Server The features listed for deprecation will compose the list of discontinued features in the next version of SQL Server Lesson: Plan to make necessary changes required to remove/replace usage of the deprecated features with the latest recommended replacements Once a feature appears on the list, it moves from bottom to the top, i.e. it is first marked as “Deprecated” and then “Discontinued”. We know of “Breaking change” comes later on in the product life cycle. What this means is that if you want to know what features would not work with SQL Server 2012 (and you are currently using SQL Server 2008 R2), you need to refer the list of breaking changes and discontinued features in SQL Server 2012. Use the tools! There are a lot of tools and technologies around us, but it is rarely that I find teams using these tools religiously and to the best of their potential. Below are the top two tools, from Microsoft, that I use every time I plan a database upgrade. The SQL Server Upgrade Advisor Ever since SQL Server 2005 was announced, Microsoft provides a small, very light-weight tool called the “SQL Server upgrade advisor”. The upgrade advisor analyzes installed components from earlier versions of SQL Server, and then generates a report that identifies issues to fix either before or after you upgrade. The analysis examines objects that can be accessed, such as scripts, stored procedures, triggers, and trace files. Upgrade Advisor cannot analyze desktop applications or encrypted stored procedures. Refer the links towards the end of the post to know how to get the Upgrade Advisor. The SQL Server Profiler Another great tool that you can use is the one most SQL Server developers & administrators use often – the SQL Server profiler. SQL Server Profiler provides functionality to monitor the “Deprecation” event, which contains: Deprecation announcement – equivalent to features to be deprecated in a future release of SQL Server Deprecation final support – equivalent to features to be deprecated in the next release of SQL Server You can learn more using the links towards the end of the post. A basic checklist There are a lot of finer points that need to be taken care of when upgrading your database. But, it would be worth-while to identify a few basic steps in order to make your database compliant with the next version of SQL Server: Monitor the current application workload (on a test bed) via the Profiler in order to identify usage of features marked as Deprecated If none appear, you are all set! (This almost never happens) Note down all the offending queries and feature usages Run analysis sessions using the SQL Server upgrade advisor on your database Based on the inputs from the analysis report and Profiler trace sessions, Incorporate solutions for the breaking changes first Next, incorporate solutions for the discontinued features Revisit and document the upgrade strategy for your deployment scenarios Revisit the fall-back, i.e. rollback strategies in case the upgrades fail Because some programming changes are dependent upon the SQL server version, this may need to be done in consultation with the development teams Before any other enhancements are incorporated by the development team, send out the database changes into QA QA strategy should involve a comparison between an environment running the old version of SQL Server against the new one Because minimal application changes have gone in (essential changes for SQL Server version compliance only), this would be possible As an ongoing activity, keep incorporating changes recommended as per the deprecated features list As a DBA, update your coding standards to ensure that the developers are using ANSI compliant code – this code will require a change only if the ANSI standard changes Remember this: Change management is a continuous process. Keep revisiting the product release notes and incorporate recommended changes to stay prepared for the next release of SQL Server. May the power of SQL Server be with you! Links Referenced in this post Breaking changes in SQL Server 2012: Link Discontinued features in SQL Server 2012: Link Get the upgrade advisor from the Microsoft Download Center at: Link Upgrade Advisor page on MSDN: Link Profiler: Review T-SQL code to identify objects no longer supported by Microsoft: Link Upgrading to SQL Server 2012 by Vinod Kumar: Link Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: Upgrade

  Read the article

• Improving Manageability of Virtual Environments

  - by Jeff Victor

  Boot Environments for Solaris 10 Branded Zones Until recently, Solaris 10 Branded Zones on Solaris 11 suffered one notable regression: Live Upgrade did not work. The individual packaging and patching tools work correctly, but the ability to upgrade Solaris while the production workload continued running did not exist. A recent Solaris 11 SRU (Solaris 11.1 SRU 6.4) restored most of that functionality, although with a slightly different concept, different commands, and without all of the feature details. This new method gives you the ability to create and manage multiple boot environments (BEs) for a Solaris 10 Branded Zone, and modify the active or any inactive BE, and to do so while the production workload continues to run. Background In case you are new to Solaris: Solaris includes a set of features that enables you to create a bootable Solaris image, called a Boot Environment (BE). This newly created image can be modified while the original BE is still running your workload(s). There are many benefits, including improved uptime and the ability to reboot into (or downgrade to) an older BE if a newer one has a problem. In Solaris 10 this set of features was named Live Upgrade. Solaris 11 applies the same basic concepts to the new packaging system (IPS) but there isn't a specific name for the feature set. The features are simply part of IPS. Solaris 11 Boot Environments are not discussed in this blog entry. Although a Solaris 10 system can have multiple BEs, until recently a Solaris 10 Branded Zone (BZ) in a Solaris 11 system did not have this ability. This limitation was addressed recently, and that enhancement is the subject of this blog entry. This new implementation uses two concepts. The first is the use of a ZFS clone for each BE. This makes it very easy to create a BE, or many BEs. This is a distinct advantage over the Live Upgrade feature set in Solaris 10, which had a practical limitation of two BEs on a system, when using UFS. The second new concept is a very simple mechanism to indicate the BE that should be booted: a ZFS property. The new ZFS property is named com.oracle.zones.solaris10:activebe (isn't that creative? ). It's important to note that the property is inherited from the original BE's file system to any BEs you create. In other words, all BEs in one zone have the same value for that property. When the (Solaris 11) global zone boots the Solaris 10 BZ, it boots the BE that has the name that is stored in the activebe property. Here is a quick summary of the actions you can use to manage these BEs: To create a BE: Create a ZFS clone of the zone's root dataset To activate a BE: Set the ZFS property of the root dataset to indicate the BE To add a package or patch to an inactive BE: Mount the inactive BE Add packages or patches to it Unmount the inactive BE To list the available BEs: Use the "zfs list" command. To destroy a BE: Use the "zfs destroy" command. Preparation Before you can use the new features, you will need a Solaris 10 BZ on a Solaris 11 system. You can use these three steps - on a real Solaris 11.1 server or in a VirtualBox guest running Solaris 11.1 - to create a Solaris 10 BZ. The Solaris 11.1 environment must be at SRU 6.4 or newer. Create a flash archive on the Solaris 10 system s10# flarcreate -n s10-system /net/zones/archives/s10-system.flar Configure the Solaris 10 BZ on the Solaris 11 system s11# zonecfg -z s10z Use 'create' to begin configuring a new zone. zonecfg:s10z create -t SYSsolaris10 zonecfg:s10z set zonepath=/zones/s10z zonecfg:s10z exit s11# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - s10z configured /zones/s10z solaris10 excl Install the zone from the flash archive s11# zoneadm -z s10z install -a /net/zones/archives/s10-system.flar -p You can find more information about the migration of Solaris 10 environments to Solaris 10 Branded Zones in the documentation. The rest of this blog entry demonstrates the commands you can use to accomplish the aforementioned actions related to BEs. New features in action Note that the demonstration of the commands occurs in the Solaris 10 BZ, as indicated by the shell prompt "s10z# ". Many of these commands can be performed in the global zone instead, if you prefer. If you perform them in the global zone, you must change the ZFS file system names. Create The only complicated action is the creation of a BE. In the Solaris 10 BZ, create a new "boot environment" - a ZFS clone. You can assign any name to the final portion of the clone's name, as long as it meets the requirements for a ZFS file system name. s10z# zfs snapshot rpool/ROOT/zbe-0@snap s10z# zfs clone -o mountpoint=/ -o canmount=noauto rpool/ROOT/zbe-0@snap rpool/ROOT/newBE cannot mount 'rpool/ROOT/newBE' on '/': directory is not empty filesystem successfully created, but not mounted You can safely ignore that message: we already know that / is not empty! We have merely told ZFS that the default mountpoint for the clone is the root directory. List the available BEs and active BE Because each BE is represented by a clone of the rpool/ROOT dataset, listing the BEs is as simple as listing the clones. s10z# zfs list -r rpool/ROOT NAME USED AVAIL REFER MOUNTPOINT rpool/ROOT 3.55G 42.9G 31K legacy rpool/ROOT/zbe-0 1K 42.9G 3.55G / rpool/ROOT/newBE 3.55G 42.9G 3.55G / The output shows that two BEs exist. Their names are "zbe-0" and "newBE". You can tell Solaris that one particular BE should be used when the zone next boots by using a ZFS property. Its name is com.oracle.zones.solaris10:activebe. The value of that property is the name of the clone that contains the BE that should be booted. s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe zbe-0 local Change the active BE When you want to change the BE that will be booted next time, you can just change the activebe property on the rpool/ROOT dataset. s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe zbe-0 local s10z# zfs set com.oracle.zones.solaris10:activebe=newBE rpool/ROOT s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe newBE local s10z# shutdown -y -g0 -i6 After the zone has rebooted: s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT rpool/ROOT com.oracle.zones.solaris10:activebe newBE local s10z# zfs mount rpool/ROOT/newBE / rpool/export /export rpool/export/home /export/home rpool /rpool Mount the original BE to see that it's still there. s10z# zfs mount -o mountpoint=/mnt rpool/ROOT/zbe-0 s10z# ls /mnt Desktop export platform Documents export.backup.20130607T214951Z proc S10Flar home rpool TT_DB kernel sbin bin lib system boot lost+found tmp cdrom mnt usr dev net var etc opt Patch an inactive BE At this point, you can modify the original BE. If you would prefer to modify the new BE, you can restore the original value to the activebe property and reboot, and then mount the new BE to /mnt (or another empty directory) and modify it. Let's mount the original BE so we can modify it. (The first command is only needed if you haven't already mounted that BE.) s10z# zfs mount -o mountpoint=/mnt rpool/ROOT/zbe-0 s10z# patchadd -R /mnt -M /var/sadm/spool 104945-02 Note that the typical usage will be: Create a BE Mount the new (inactive) BE Use the package and patch tools to update the new BE Unmount the new BE Reboot Delete an inactive BE ZFS clones are children of their parent file systems. In order to destroy the parent, you must first "promote" the child. This reverses the parent-child relationship. (For more information on this, see the documentation.) The original rpool/ROOT file system is the parent of the clones that you create as BEs. In order to destroy an earlier BE that is that parent of other BEs, you must first promote one of the child BEs to be the ZFS parent. Only then can you destroy the original BE. Fortunately, this is easier to do than to explain: s10z# zfs promote rpool/ROOT/newBE s10z# zfs destroy rpool/ROOT/zbe-0 s10z# zfs list -r rpool/ROOT NAME USED AVAIL REFER MOUNTPOINT rpool/ROOT 3.56G 269G 31K legacy rpool/ROOT/newBE 3.56G 269G 3.55G / Documentation This feature is so new, it is not yet described in the Solaris 11 documentation. However, MOS note 1558773.1 offers some details. Conclusion With this new feature, you can add and patch packages to boot environments of a Solaris 10 Branded Zone. This ability improves the manageability of these zones, and makes their use more practical. It also means that you can use the existing P2V tools with earlier Solaris 10 updates, and modify the environments after they become Solaris 10 Branded Zones.

  Read the article

• Why did Ubuntu suddenly get so slow?

  - by user101383

  12.10 has been slowing down mysteriously. Normally, in past versions, I can log in, open Firefox, and it will pop up within seconds. 12.10 is like that upon install too, though once I install my old apps, it gets very slow by Ubuntu standards. After login the hard drive will just make noise for a while before the OS will do anything. Hardware: enter description: Desktop Computer product: XPS 8300 () vendor: Dell Inc. serial: B6G2WR1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=desktop uuid=44454C4C-3600-1047-8032-C2C04F575231 core description: Motherboard product: 0Y2MRG vendor: Dell Inc. physical id: 0 version: A00 serial: ..CN7360419G04VQ. slot: To Be Filled By O.E.M. *cpu description: CPU product: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 1600MHz capacity: 1600MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 256KiB capacity: 256KiB capabilities: internal write-through unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 1MiB capacity: 1MiB capabilities: internal write-through unified *-cache:2 DISABLED description: L3 cache physical id: 7 slot: L3-Cache size: 8MiB capacity: 8MiB capabilities: internal write-back unified *-memory description: System Memory physical id: 20 slot: System board or motherboard size: 8GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 0 serial: 7228183 slot: DIMM3 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 1 serial: 1E28183 slot: DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 2 serial: 9E28183 slot: DIMM4 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NF-CG vendor: Nanya physical id: 3 serial: 5527183 slot: DIMM2 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A05 date: 09/21/2011 size: 64KiB capacity: 4032KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:e000(size=4096) memory:fe600000-fe6fffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: Juniper [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:d0000000-dfffffff memory:fe620000-fe63ffff ioport:e000(size=256) memory:fe600000-fe61ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Advanced Micro Devices [AMD] nee ATI physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:48 memory:fe640000-fe643fff *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:45 memory:fe708000-fe70800f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fe707000-fe7073ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:46 memory:fe700000-fe703fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 memory:fe500000-fe5fffff *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:16 memory:fe500000-fe503fff *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 memory:fe400000-fe4fffff *-network description: Ethernet interface product: NetLink BCM57788 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 18:03:73:e1:a7:71 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:47 memory:fe400000-fe40ffff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fe706000-fe7063ff *-isa description: ISA bridge product: H67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list configuration: driver=ahci latency=0 resources: irq:43 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fe705000-fe7057ff *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fe704000-fe7040ff ioport:f000(size=32) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: Hitachi HUA72201 vendor: Hitachi physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: JP4O serial: JPW9J0HD21BTZC size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=000641dc *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: 4e3d91b7-fd38-4f44-a9e9-ba3c39b926ec size: 585GiB capacity: 585GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-10-21 16:26:50 filesystem=ext4 lastmountpoint=/ modified=2012-10-29 18:12:08 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered mounted=2012-10-29 18:12:08 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 7823MiB capacity: 7823MiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 7823MiB capabilities: nofs *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 84a92aae-347b-7940-a2d1-f4745b885ef2 size: 337GiB capacity: 337GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-10-21 18:43:39 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVDRWBD DH-12E3S vendor: PLDS physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: MD11 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-scsi:2 physical id: 3 bus info: usb@2:1.8 logical name: scsi6 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@6:0.0.0 logical name: /dev/sdb configuration: sectorsize=512 *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@6:0.0.1 logical name: /dev/sdc configuration: sectorsize=512 *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@6:0.0.2 logical name: /dev/sdd configuration: sectorsize=512 *-disk:3 description: SCSI Disk product: MS/MS-Pro vendor: Generic- physical id: 0.0.3 bus info: scsi@6:0.0.3 logical name: /dev/sde version: 1.03 serial: 3 capabilities: removable configuration: sectorsize=512 *-medium physical id: 0 logical name: /dev/sde

  Read the article

• NVIDIA x server - "sudo nvidia config" does not generate a working 'xorg.config'

  - by Mike

  I am over 18 hours deep on this challenge. I got to this point and am stuck. very stuck. Maybe you can figure it out? Ubuntu Version 12.04 LTS with all the updates installed. Problem: The default settings in "etc/X11/xorg.conf" that are generated by the "nvidia-xconfig" tool, do not allow the NVIDIA x server to connect to the driver in my "System Settings Additional Driver window". (that's how I understand it. Lots of information below). Symptoms of Problem "System Settings Additional Driver" window has drivers, but the nvidia x server cannot connect/utilize any of the 4 drivers. the drivers are activated, but not in use. When I go to "System Tools Administration NVIDIA x server settings" I get an error that basically tells me to create a default file to initialize the NVIDIA X server (screen shot below). This is the messages the terminal gives after running a "sudo nvidia-xconfig" command for the first time. It seems that the generated file by the tool i just ran is generating a bad/unusable file: If I run the "sudo nvidia-xconfig" command again, I wont get an error the second time. However when I reboot, the default file that is generated (etc/X11/xorg.conf) simply puts the screen resolution at 800 x 600 (or something big like that). When I try to go to NVIDIA x server settings I am greeted with the same screen as the screen shot as in symptom 2 (no option to change the resolution). If I try to go to "system settings display" there are no other resolutions to choose from. At this point I must delete the newly minted "xorg.conf" and reinstate the original in its place. Here are the contents of the "xorg.conf" that is generated first (the one missing required information): # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 304.88 (buildmeister@swio-display-x86-rhel47-06) Wed Mar 27 15:32:58 PDT 2013 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Hardware: I ran the "lspci|grep VGA". There results are: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) More Hardware info: Ram: 16GB CPU: Intel Core i7-2720QM @2.2GHz * 8 Other: 64 bit. This is a triple boot computer and not a VM. Attempts With Not Success on My End: 1) Tried to append the "xorg.conf" with what I perceive is missing information and obviously it didn't fly. 2) All the other stuff I tried got me to this point. 3) See if this link is helpful to you (I barely get it, but i get enough knowing that a smarter person might find this useful): http://manpages.ubuntu.com/manpages/lucid/man1/nvidia-xconfig.1.html 4) I am completely new to Linux (40 hours over past week), but not to programming. However I am very serious about changing over to Linux. When you respond (I hope someone responds...) please respond in a way that a person new to Linux can understand. 5) By the way, the reason I am in this mess is because I MUST have a second monitor running from my laptop, and "System Settings Display" doesn't recognize my second display. I know it is possible to make the second display work in my system, because when I boot from the install CD, I perform work on the native laptop monitor, but the second monitor shows a purple screen with Ubuntu in the middle, so I know the VGA port is sending a signal out. If this is too much for you to tackle please suggest an alternative method to get a second display. I don't want to go to windows but I cannot have a single display. I am really fudged here. I hope some smart person can help. Thanks in advance. Mike. **********************EDIT #1********************** More Details About Graphics Card I was asked "which brand of nvidia-card do you have exactly?" Here is what I did to provide more info (maybe relevant, maybe not, but here is everything): 1) Took my Lenovo W520 right apart to see if there is an identifier on the actual card. However I realized that if I get deep enough to take a look, the laptop "won't like it". so I put it back together. Figuring out the card this way is not an option for me right now. 2) (My computer is triple boot) I logged into Win7 and ran 'dxdiag' command. here is the screen shot: 3) I tried to look on the lenovo website for more details... but no luck. I took a look at my receipts and here is info form receipt: System Unit: W520 NVIDIA Quadro 1000M 2GB 4) In win7 I went to the NVIDIA website and used the option to have my card 'scanned' by a Java applet to determine the latest update for my card. I tried the same with Ubuntu but I can't get the applet to run. Here is the recommended driver from from the NVIDIA Applet for my card for Win7 (I hope this shines some light on the specifics of the card): Quadro/NVS/Tesla/GRID Desktop Driver Release R319 Version: 320.00 WHQL Release Date: 3.5.2013 5) Also I went on the NVIDIA driver search and looked through every possible combination of product type + product series + product to find all the combinations that yield a 1000M card. My card is: Product Type: Quadro Product Series: Quadro Series (Notebooks) Product: 1000M ***********************EDIT #2******************* Additional Symptoms Another question that generated more symptoms I previously didn't mention was: "After generating xorg.conf by nvidia-xconfig, go to additional drivers, do you see nvidia-304?" 1) I took a screen shot of the "additional drivers" right after generating xorg.conf by nvidia-xconfig. Here it is: 2) Then I did a reboot. Now Ubuntu is 600 x 800 resolution. When I logged in after the computer came up I got an error (which I always get after generating xorg.conf by nvidia-xconfig and rebooting) 3) To finally answer the question - No. There is no "NVIDIA-304" driver. Screen shot of additional drivers after generating xorg.conf by nvidia-xconfig and rebooting : At this point I revert to the original xorg.conf and delete the xorg.conf generated by Nvidia.

  Read the article

• tile_static, tile_barrier, and tiled matrix multiplication with C++ AMP

  - by Daniel Moth

  We ended the previous post with a mechanical transformation of the C++ AMP matrix multiplication example to the tiled model and in the process introduced tiled_index and tiled_grid. This is part 2. tile_static memory You all know that in regular CPU code, static variables have the same value regardless of which thread accesses the static variable. This is in contrast with non-static local variables, where each thread has its own copy. Back to C++ AMP, the same rules apply and each thread has its own value for local variables in your lambda, whereas all threads see the same global memory, which is the data they have access to via the array and array_view. In addition, on an accelerator like the GPU, there is a programmable cache, a third kind of memory type if you'd like to think of it that way (some call it shared memory, others call it scratchpad memory). Variables stored in that memory share the same value for every thread in the same tile. So, when you use the tiled model, you can have variables where each thread in the same tile sees the same value for that variable, that threads from other tiles do not. The new storage class for local variables introduced for this purpose is called tile_static. You can only use tile_static in restrict(direct3d) functions, and only when explicitly using the tiled model. What this looks like in code should be no surprise, but here is a snippet to confirm your mental image, using a good old regular C array // each tile of threads has its own copy of locA, // shared among the threads of the tile tile_static float locA[16][16]; Note that tile_static variables are scoped and have the lifetime of the tile, and they cannot have constructors or destructors. tile_barrier In amp.h one of the types introduced is tile_barrier. You cannot construct this object yourself (although if you had one, you could use a copy constructor to create another one). So how do you get one of these? You get it, from a tiled_index object. Beyond the 4 properties returning index objects, tiled_index has another property, barrier, that returns a tile_barrier object. The tile_barrier class exposes a single member, the method wait. 15: // Given a tiled_index object named t_idx 16: t_idx.barrier.wait(); 17: // more code …in the code above, all threads in the tile will reach line 16 before a single one progresses to line 17. Note that all threads must be able to reach the barrier, i.e. if you had branchy code in such a way which meant that there is a chance that not all threads could reach line 16, then the code above would be illegal. Tiled Matrix Multiplication Example – part 2 So now that we added to our understanding the concepts of tile_static and tile_barrier, let me obfuscate rewrite the matrix multiplication code so that it takes advantage of tiling. Before you start reading this, I suggest you get a cup of your favorite non-alcoholic beverage to enjoy while you try to fully understand the code. 01: void MatrixMultiplyTiled(vector<float>& vC, const vector<float>& vA, const vector<float>& vB, int M, int N, int W) 02: { 03: static const int TS = 16; 04: array_view<const float,2> a(M, W, vA); 05: array_view<const float,2> b(W, N, vB); 06: array_view<writeonly<float>,2> c(M,N,vC); 07: parallel_for_each(c.grid.tile< TS, TS >(), 08: [=] (tiled_index< TS, TS> t_idx) restrict(direct3d) 09: { 10: int row = t_idx.local[0]; int col = t_idx.local[1]; 11: float sum = 0.0f; 12: for (int i = 0; i < W; i += TS) { 13: tile_static float locA[TS][TS], locB[TS][TS]; 14: locA[row][col] = a(t_idx.global[0], col + i); 15: locB[row][col] = b(row + i, t_idx.global[1]); 16: t_idx.barrier.wait(); 17: for (int k = 0; k < TS; k++) 18: sum += locA[row][k] * locB[k][col]; 19: t_idx.barrier.wait(); 20: } 21: c[t_idx.global] = sum; 22: }); 23: } Notice that all the code up to line 9 is the same as per the changes we made in part 1 of tiling introduction. If you squint, the body of the lambda itself preserves the original algorithm on lines 10, 11, and 17, 18, and 21. The difference being that those lines use new indexing and the tile_static arrays; the tile_static arrays are declared and initialized on the brand new lines 13-15. On those lines we copy from the global memory represented by the array_view objects (a and b), to the tile_static vanilla arrays (locA and locB) – we are copying enough to fit a tile. Because in the code that follows on line 18 we expect the data for this tile to be in the tile_static storage, we need to synchronize the threads within each tile with a barrier, which we do on line 16 (to avoid accessing uninitialized memory on line 18). We also need to synchronize the threads within a tile on line 19, again to avoid the race between lines 14, 15 (retrieving the next set of data for each tile and overwriting the previous set) and line 18 (not being done processing the previous set of data). Luckily, as part of the awesome C++ AMP debugger in Visual Studio there is an option that helps you find such races, but that is a story for another blog post another time. May I suggest reading the next section, and then coming back to re-read and walk through this code with pen and paper to really grok what is going on, if you haven't already? Cool. Why would I introduce this tiling complexity into my code? Funny you should ask that, I was just about to tell you. There is only one reason we tiled our extent, had to deal with finding a good tile size, ensure the number of threads we schedule are correctly divisible with the tile size, had to use a tiled_index instead of a normal index, and had to understand tile_barrier and to figure out where we need to use it, and double the size of our lambda in terms of lines of code: the reason is to be able to use tile_static memory. Why do we want to use tile_static memory? Because accessing tile_static memory is around 10 times faster than accessing the global memory on an accelerator like the GPU, e.g. in the code above, if you can get 150GB/second accessing data from the array_view a, you can get 1500GB/second accessing the tile_static array locA. And since by definition you are dealing with really large data sets, the savings really pay off. We have seen tiled implementations being twice as fast as their non-tiled counterparts. Now, some algorithms will not have performance benefits from tiling (and in fact may deteriorate), e.g. algorithms that require you to go only once to global memory will not benefit from tiling, since with tiling you already have to fetch the data once from global memory! Other algorithms may benefit, but you may decide that you are happy with your code being 150 times faster than the serial-version you had, and you do not need to invest to make it 250 times faster. Also algorithms with more than 3 dimensions, which C++ AMP supports in the non-tiled model, cannot be tiled. Also note that in future releases, we may invest in making the non-tiled model, which already uses tiling under the covers, go the extra step and use tile_static memory on your behalf, but it is obviously way to early to commit to anything like that, and we certainly don't do any of that today. Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• Developing a Cost Model for Cloud Applications

  - by BuckWoody

  Note - please pay attention to the date of this post. As much as I attempt to make the information below accurate, the nature of distributed computing means that components, units and pricing will change over time. The definitive costs for Microsoft Windows Azure and SQL Azure are located here, and are more accurate than anything you will see in this post: http://www.microsoft.com/windowsazure/offers/  When writing software that is run on a Platform-as-a-Service (PaaS) offering like Windows Azure / SQL Azure, one of the questions you must answer is how much the system will cost. I will not discuss the comparisons between on-premise costs (which are nigh impossible to calculate accurately) versus cloud costs, but instead focus on creating a general model for estimating costs for a given application. You should be aware that there are (at this writing) two billing mechanisms for Windows and SQL Azure: “Pay-as-you-go” or consumption, and “Subscription” or commitment. Conceptually, you can consider the former a pay-as-you-go cell phone plan, where you pay by the unit used (at a slightly higher rate) and the latter as a standard cell phone plan where you commit to a contract and thus pay lower rates. In this post I’ll stick with the pay-as-you-go mechanism for simplicity, which should be the maximum cost you would pay. From there you may be able to get a lower cost if you use the other mechanism. In any case, the model you create should hold. Developing a good cost model is essential. As a developer or architect, you’ll most certainly be asked how much something will cost, and you need to have a reliable way to estimate that. Businesses and Organizations have been used to paying for servers, software licenses, and other infrastructure as an up-front cost, and power, people to the systems and so on as an ongoing (and sometimes not factored) cost. When presented with a new paradigm like distributed computing, they may not understand the true cost/value proposition, and that’s where the architect and developer can guide the conversation to make a choice based on features of the application versus the true costs. The two big buckets of use-types for these applications are customer-based and steady-state. In the customer-based use type, each successful use of the program results in a sale or income for your organization. Perhaps you’ve written an application that provides the spot-price of foo, and your customer pays for the use of that application. In that case, once you’ve estimated your cost for a successful traversal of the application, you can build that into the price you charge the user. It’s a standard restaurant model, where the price of the meal is determined by the cost of making it, plus any profit you can make. In the second use-type, the application will be used by a more-or-less constant number of processes or users and no direct revenue is attached to the system. A typical example is a customer-tracking system used by the employees within your company. In this case, the cost model is often created “in reverse” - meaning that you pilot the application, monitor the use (and costs) and that cost is held steady. This is where the comparison with an on-premise system becomes necessary, even though it is more difficult to estimate those on-premise true costs. For instance, do you know exactly how much cost the air conditioning is because you have a team of system administrators? This may sound trivial, but that, along with the insurance for the building, the wiring, and every other part of the system is in fact a cost to the business. There are three primary methods that I’ve been successful with in estimating the cost. None are perfect, all are demand-driven. The general process is to lay out a matrix of: components units cost per unit and then multiply that times the usage of the system, based on which components you use in the program. That sounds a bit simplistic, but using those metrics in a calculation becomes more detailed. In all of the methods that follow, you need to know your application. The components for a PaaS include computing instances, storage, transactions, bandwidth and in the case of SQL Azure, database size. In most cases, architects start with the first model and progress through the other methods to gain accuracy. Simple Estimation The simplest way to calculate costs is to architect the application (even UML or on-paper, no coding involved) and then estimate which of the components you’ll use, and how much of each will be used. Microsoft provides two tools to do this - one is a simple slider-application located here: http://www.microsoft.com/windowsazure/pricing-calculator/  The other is a tool you download to create an “Return on Investment” (ROI) spreadsheet, which has the advantage of leading you through various questions to estimate what you plan to use, located here: https://roianalyst.alinean.com/msft/AutoLogin.do?d=176318219048082115  You can also just create a spreadsheet yourself with a structure like this: Program Element Azure Component Unit of Measure Cost Per Unit Estimated Use of Component Total Cost Per Component Cumulative Cost               Of course, the consideration with this model is that it is difficult to predict a system that is not running or hasn’t even been developed. Which brings us to the next model type. Measure and Project A more accurate model is to actually write the code for the application, using the Software Development Kit (SDK) which can run entirely disconnected from Azure. The code should be instrumented to estimate the use of the application components, logging to a local file on the development system. A series of unit and integration tests should be run, which will create load on the test system. You can use standard development concepts to track this usage, and even use Windows Performance Monitor counters. The best place to start with this method is to use the Windows Azure Diagnostics subsystem in your code, which you can read more about here: http://blogs.msdn.com/b/sumitm/archive/2009/11/18/introducing-windows-azure-diagnostics.aspx This set of API’s greatly simplifies tracking the application, and in fact you can use this information for more than just a cost model. After you have the tracking logs, you can plug the numbers into ay of the tools above, which should give a representative cost or in some cases a unit cost. The consideration with this model is that the SDK fabric is not a one-to-one comparison with performance on the actual Windows Azure fabric. Those differences are usually smaller, but they do need to be considered. Also, you may not be able to accurately predict the load on the system, which might lead to an architectural change, which changes the model. This leads us to the next, most accurate method for a cost model. Sample and Estimate Using standard statistical and other predictive math, once the application is deployed you will get a bill each month from Microsoft for your Azure usage. The bill is quite detailed, and you can export the data from it to do analysis, and using methods like regression and so on project out into the future what the costs will be. I normally advise that the architect also extrapolate a unit cost from those metrics as well. This is the information that should be reported back to the executives that pay the bills: the past cost, future projected costs, and unit cost “per click” or “per transaction”, as your case warrants. The challenge here is in the model itself - statistical methods are not foolproof, and the larger the sample (in this case I recommend the entire population, not a smaller sample) is key. References and Tools Articles: http://blogs.msdn.com/b/patrick_butler_monterde/archive/2010/02/10/windows-azure-billing-overview.aspx http://technet.microsoft.com/en-us/magazine/gg213848.aspx http://blog.codingoutloud.com/2011/06/05/azure-faq-how-much-will-it-cost-me-to-run-my-application-on-windows-azure/ http://blogs.msdn.com/b/johnalioto/archive/2010/08/25/10054193.aspx http://geekswithblogs.net/iupdateable/archive/2010/02/08/qampa-how-can-i-calculate-the-tco-and-roi-when.aspx   Other Tools: http://cloud-assessment.com/ http://communities.quest.com/community/cloud_tools

  Read the article

• CodePlex Daily Summary for Thursday, September 06, 2012

  CodePlex Daily Summary for Thursday, September 06, 2012Popular Releasesmenu4web: menu4web 0.4.1 - javascript menu for web sites: This release is for those who believe that global variables are evil. menu4web has been wrapped into m4w singleton object. Added "Vertical Tabs" example which illustrates object notation.WinRT XAML Toolkit: WinRT XAML Toolkit - 1.2.1: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features AsyncUI extensions Controls and control extensions Converters Debugging helpers Imaging IO helpers VisualTree helpers Samples Recent changes NOTE: Namespace changes DebugConsol...iPDC - Free Phasor Data Concentrator: iPDC-v1.3.1: iPDC suite version-1.3.1, Modifications and Bug Fixed (from v 1.3.0) New User Manual for iPDC-v1.3.1 available on websites. Bug resolved : PMU Simulator TCP connection error and hang connection for client (PDC). Now PMU Simulator (server) can communicate more than one PDCs (clients) over TCP and UDP parallely. PMU Simulator is now sending the exact data frames as mentioned in data rate by user. PMU Simulator data rate has been verified by iPDC database entries and PMU Connection Tes...Microsoft SQL Server Product Samples: Database: AdventureWorks OData Feed: The AdventureWorks OData service exposes resources based on specific SQL views. The SQL views are a limited subset of the AdventureWorks database that results in several consuming scenarios: CompanySales Documents ManufacturingInstructions ProductCatalog TerritorySalesDrilldown WorkOrderRouting How to install the sample You can consume the AdventureWorks OData feed from http://services.odata.org/AdventureWorksV3/AdventureWorks.svc. You can also consume the AdventureWorks OData fe...Desktop Google Reader: 1.4.6: Sorting feeds alphabetical is now optional (see preferences window)DotNetNuke® Community Edition CMS: 06.02.03: Major Highlights Fixed issue where mailto: links were not working when sending bulk email Fixed issue where uses did not see friendship relationships Problem is in 6.2, which does not show in the Versions Affected list above. Fixed the issue with cascade deletes in comments in CoreMessaging_Notification Fixed UI issue when using a date fields as a required profile property during user registration Fixed error when running the product in debug mode Fixed visibility issue when...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.65: Fixed null-reference error in the build task constructor.Active Forums for DotNetNuke CMS: Active Forums 5.0.0 RC: RC release of Active Forums 5.0.Droid Explorer: Droid Explorer 0.8.8.7 Beta: Bug in the display icon for apk's, will fix with next release Added fallback icon if unable to get the image/icon from the Cloud Service Removed some stale plugins that were either out dated or incomplete. Added handler for *.ab files for restoring backups Added plugin to create device backups Backups stored in %USERPROFILE%\Android Backups\%DEVICE_ID%\ Added custom folder icon for the android backups directory better error handling for installing an apk bug fixes for the Runn...BI System Monitor: v2.1: Data Audits report and supporting SQL, and SSIS package Environment Overview report enhancements, improving the appearance, addition of data audit finding indicators Note: SQL 2012 version coming soon.Hidden Capture (HC): Hidden Capture 1.1: Hidden Capture 1.1 by Mohsen E.Dawatgar http://Hidden-Capture.blogfa.comExt Spec: Ext Spec 0.2.1: Refined examples and improved distribution options.The Visual Guide for Building Team Foundation Server 2012 Environments: Version 1: --Nearforums - ASP.NET MVC forum engine: Nearforums v8.5: Version 8.5 of Nearforums, the ASP.NET MVC Forum Engine. New features include: Built-in search engine using Lucene.NET Flood control improvements Notifications improvements: sync option and mail body View Roadmap for more details webdeploy package sha1 checksum: 961aff884a9187b6e8a86d68913cdd31f8deaf83WiX Toolset: WiX Toolset v3.6: WiX Toolset v3.6 introduces the Burn bootstrapper/chaining engine and support for Visual Studio 2012 and .NET Framework 4.5. Other minor functionality includes: WixDependencyExtension supports dependency checking among MSI packages. WixFirewallExtension supports more features of Windows Firewall. WixTagExtension supports Software Id Tagging. WixUtilExtension now supports recursive directory deletion. Melt simplifies pure-WiX patching by extracting .msi package content and updating .w...Iveely Search Engine: Iveely Search Engine （0.2.0）: ????ISE?0.1.0??，?????，ISE?0.2.0?????????，???????，????????20???follow?ISE，????，??ISE??????????，??????????，?????????，?????????0.2.0??????，??????????。 Iveely Search Engine ?0.2.0?????????“??????????”，??????，?????????，???????，???????????????????，????、????????????。???0.1.0????????????： 1. ??“????” ??。??????????，?????????，???????????????????。??：????????，????????????，??????????????????。??????。 2. ??“????”??。?0.1.0??????，???????，???????????????，?????????????，????????，?0.2.0?，???????...GmailDefaultMaker: GmailDefaultMaker 3.0.0.2: Add QQ Mail BugfixSmart Data Access layer: Smart Data access Layer Ver 3: In this version support executing inline query is added. Check Documentation section for detail.DotNetNuke® Form and List: 06.00.04: DotNetNuke Form and List 06.00.04 Don't forget to backup your installation before upgrade. Changes in 06.00.04 Fix: Sql Scripts for 6.003 missed object qualifiers within stored procedures Fix: added missing resource "cmdCancel.Text" in form.ascx.resx Changes in 06.00.03 Fix: MakeThumbnail was broken if the application pool was configured to .Net 4 Change: Data is now stored in nvarchar(max) instead of ntext Changes in 06.00.02 The scripts are now compatible with SQL Azure, tested in a ne...Coevery - Free CRM: Coevery 1.0.0.24: Add a sample database, and installation instructions.New ProjectsAny-Service: AnyService is a .net 4.0 Windows service shell. It hosts any windows application in non-gui mode to run as a service.BabyCloudDrives - the multi cloud drive desktop's application: wpf ????BLACK ORANGE: Download The HPAD TEXT EDITOR and use it Wisely.. CodePlex New Release Checker: CodePlex New Release Checker is a small library that makes it easy to add, "New Version Available!" functionality to your CodePlex project.Collect: ????????！CSVManager: CSV??CSV?????，????CSV??，??????Exam Project: My Exam Project. Computer Vision, C and OpenCV-FTP: Hey guys thanks for checking out my ftp!Haushaltsbuch: 1ModMaker.Lua: ModMaker.Lua is an open source .NET library that parses and executes Lua code.MyJabbr: MyJabbr netduinoscope: Design shield and software to use netduino as oscilloscopeNetSurveillance Web Application: Net Surveillance Web ApplicationNiconicoApiHelper: ????API?????????OStega: A simple library for encrypt text into an bmp or png image.OURORM: ormTFS Cloud Deployment Toolkit: The TFS Cloud Deployment Toolkit is a set of tools that integrate with TFS 2010 to help manage configuration and deployment to various remote environments.The Visual Guide for Building Team Foundation Server 2012 Environments: A step-by-step guide for building Team Foundation Server 2012 environments that include SharePoint Server 2010, SQL Server 2012, Windows Server 2012 and more!WinRT LineChart: An attempt at creating an usable LineChart for everyone to use in his/her own Windows 8 Apps

  Read the article

• Scheduling thread tiles with C++ AMP

  - by Daniel Moth

  This post assumes you are totally comfortable with, what some of us call, the simple model of C++ AMP, i.e. you could write your own matrix multiplication. We are now ready to explore the tiled model, which builds on top of the non-tiled one. Tiling the extent We know that when we pass a grid (which is just an extent under the covers) to the parallel_for_each call, it determines the number of threads to schedule and their index values (including dimensionality). For the single-, two-, and three- dimensional cases you can go a step further and subdivide the threads into what we call tiles of threads (others may call them thread groups). So here is a single-dimensional example: extent<1> e(20); // 20 units in a single dimension with indices from 0-19 grid<1> g(e);      // same as extent tiled_grid<4> tg = g.tile<4>(); …on the 3rd line we subdivided the single-dimensional space into 5 single-dimensional tiles each having 4 elements, and we captured that result in a concurrency::tiled_grid (a new class in amp.h). Let's move on swiftly to another example, in pictures, this time 2-dimensional: So we start on the left with a grid of a 2-dimensional extent which has 8*6=48 threads. We then have two different examples of tiling. In the first case, in the middle, we subdivide the 48 threads into tiles where each has 4*3=12 threads, hence we have 2*2=4 tiles. In the second example, on the right, we subdivide the original input into tiles where each has 2*2=4 threads, hence we have 4*3=12 tiles. Notice how you can play with the tile size and achieve different number of tiles. The numbers you pick must be such that the original total number of threads (in our example 48), remains the same, and every tile must have the same size. Of course, you still have no clue why you would do that, but stick with me. First, we should see how we can use this tiled_grid, since the parallel_for_each function that we know expects a grid. Tiled parallel_for_each and tiled_index It turns out that we have additional overloads of parallel_for_each that accept a tiled_grid instead of a grid. However, those overloads, also expect that the lambda you pass in accepts a concurrency::tiled_index (new in amp.h), not an index<N>. So how is a tiled_index different to an index? A tiled_index object, can have only 1 or 2 or 3 dimensions (matching exactly the tiled_grid), and consists of 4 index objects that are accessible via properties: global, local, tile_origin, and tile. The global index is the same as the index we know and love: the global thread ID. The local index is the local thread ID within the tile. The tile_origin index returns the global index of the thread that is at position 0,0 of this tile, and the tile index is the position of the tile in relation to the overall grid. Confused? Here is an example accompanied by a picture that hopefully clarifies things: array_view<int, 2> data(8, 6, p_my_data); parallel_for_each(data.grid.tile<2,2>(), [=] (tiled_index<2,2> t_idx) restrict(direct3d) { /* todo */ }); Given the code above and the picture on the right, what are the values of each of the 4 index objects that the t_idx variables exposes, when the lambda is executed by T (highlighted in the picture on the right)? If you can't work it out yourselves, the solution follows: t_idx.global       = index<2> (6,3) t_idx.local          = index<2> (0,1) t_idx.tile_origin = index<2> (6,2) t_idx.tile             = index<2> (3,1) Don't move on until you are comfortable with this… the picture really helps, so use it. Tiled Matrix Multiplication Example – part 1 Let's paste here the C++ AMP matrix multiplication example, bolding the lines we are going to change (can you guess what the changes will be?) 01: void MatrixMultiplyTiled_Part1(vector<float>& vC, const vector<float>& vA, const vector<float>& vB, int M, int N, int W) 02: { 03: 04: array_view<const float,2> a(M, W, vA); 05: array_view<const float,2> b(W, N, vB); 06: array_view<writeonly<float>,2> c(M, N, vC); 07: parallel_for_each(c.grid, 08: [=](index<2> idx) restrict(direct3d) { 09: 10: int row = idx[0]; int col = idx[1]; 11: float sum = 0.0f; 12: for(int i = 0; i < W; i++) 13: sum += a(row, i) * b(i, col); 14: c[idx] = sum; 15: }); 16: } To turn this into a tiled example, first we need to decide our tile size. Let's say we want each tile to be 16*16 (which assumes that we'll have at least 256 threads to process, and that c.grid.extent.size() is divisible by 256, and moreover that c.grid.extent[0] and c.grid.extent[1] are divisible by 16). So we insert at line 03 the tile size (which must be a compile time constant). 03: static const int TS = 16; ...then we need to tile the grid to have tiles where each one has 16*16 threads, so we change line 07 to be as follows 07: parallel_for_each(c.grid.tile<TS,TS>(), ...that means that our index now has to be a tiled_index with the same characteristics as the tiled_grid, so we change line 08 08: [=](tiled_index<TS, TS> t_idx) restrict(direct3d) { ...which means, without changing our core algorithm, we need to be using the global index that the tiled_index gives us access to, so we insert line 09 as follows 09: index<2> idx = t_idx.global; ...and now this code just works and it is tiled! Closing thoughts on part 1 The process we followed just shows the mechanical transformation that can take place from the simple model to the tiled model (think of this as step 1). In fact, when we wrote the matrix multiplication example originally, the compiler was doing this mechanical transformation under the covers for us (and it has additional smarts to deal with the cases where the total number of threads scheduled cannot be divisible by the tile size). The point is that the thread scheduling is always tiled, even when you use the non-tiled model. But with this mechanical transformation, we haven't gained anything… Hint: our goal with explicitly using the tiled model is to gain even more performance. In the next post, we'll evolve this further (beyond what the compiler can automatically do for us, in this first release), so you can see the full usage of the tiled model and its benefits… Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• Kubuntu 12.04 - Touchpad and keyboard stopped working at random

  - by StepTNT

  As in the title, I've got this problem with my Kubuntu 12.04. At first I've thought that the whole system was hung, but it happened again 5 minutes ago and, while the keyboard and the touchpad stopped working, the music was still playing, so I guess that's just an "input" problem, because the system was still working! Any solution? Is there some data that you need to know about my setup? EDIT: Added my lshw outout description: Notebook product: N53SV () vendor: ASUSTeK Computer Inc. version: 1.0 serial: B2N0AS17695408A width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=N uuid=8083F2DA-A43E-E081-3F3F-BCAEC55F8AA1 *-core description: Motherboard product: N53SV vendor: ASUSTeK Computer Inc. physical id: 0 version: 1.0 serial: BSN12345678901234567 slot: MIDDLE *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: N53SV.214 date: 08/10/2011 size: 64KiB capacity: 2496KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb smartbattery biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 800MHz capacity: 4GHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer xsave avx lahf_lm ida arat epb xsaveopt pln pts tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache description: L1 cache physical id: 5 slot: L1-Cache size: 32KiB capacity: 32KiB capabilities: internal write-back instruction *-memory description: System Memory physical id: 40 slot: System board or motherboard size: 10GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: 99U5428-040.A00LF vendor: Kingston physical id: 0 serial: 103C28C3 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 58383D1F slot: ChannelA-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 2 serial: 58183D19 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 3 serial: 58183C8F slot: ChannelB-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:d000(size=4096) memory:db000000-dc0fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:db000000-dbffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:d000(size=128) memory:dc000000-dc07ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:dc400000-dc7fffff memory:b0000000-bfffffff ioport:e000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:48 memory:df00b000-df00b00f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:df008000-df0083ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:49 memory:df000000-df003fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:c000(size=4096) memory:de600000-deffffff ioport:d4200000(size=10485760) *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:b000(size=4096) memory:ddc00000-de5fffff ioport:d3700000(size=10485760) *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 48:5d:60:f2:2c:fd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-24-generic firmware=N/A ip=192.168.1.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:ddc00000-ddc0ffff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:a000(size=4096) memory:dd200000-ddbfffff ioport:d2c00000(size=10485760) *-usb description: USB controller product: FL1000G USB 3.0 Host Controller vendor: Fresco Logic physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:dd200000-dd20ffff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:44 ioport:9000(size=4096) memory:dc800000-dd1fffff ioport:d2100000(size=10485760) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: bc:ae:c5:5f:8a:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168e-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:46 ioport:9000(size=256) memory:d2104000-d2104fff memory:d2100000-d2103fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:df007000-df0073ff *-isa description: ISA bridge product: HM65 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:e0b0(size=8) ioport:e0a0(size=4) ioport:e090(size=8) ioport:e080(size=4) ioport:e060(size=32) memory:df006000-df0067ff *-disk description: ATA Disk product: ST9750420AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 0002 serial: 5WS0A7QR size: 698GiB (750GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=e0c5913d *-volume:0 description: Windows FAT volume vendor: MSDOS5.0 physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: FAT32 serial: 4ce5-3acb size: 3004MiB capacity: 3004MiB capabilities: primary fat initialized configuration: FATs=2 filesystem=fat *-volume:1 description: EXT4 volume vendor: Linux physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 logical name: / version: 1.0 serial: c198cc2a-d86a-4460-a4d5-3fc0b21e439c size: 28GiB capacity: 28GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-03-15 16:53:54 filesystem=ext4 lastmountpoint=/ modified=2012-05-02 18:52:04 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,acl,barrier=1,data=ordered mounted=2012-05-09 19:06:01 state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 4c1cdebc-ec09-2947-a3b5-c1f9f1cddc1c size: 152GiB capacity: 152GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-02-22 16:02:47 filesystem=ntfs label=OS state=clean *-volume:3 description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 size: 514GiB capacity: 514GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 10GiB capabilities: nofs *-logicalvolume:1 description: HPFS/NTFS partition physical id: 6 logical name: /dev/sda6 capacity: 504GiB *-cdrom description: DVD-RAM writer product: BD-MLT UJ240AS vendor: MATSHITA physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 1.00 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:df005000-df0050ff ioport:e040(size=32)

  Read the article

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• 12c - SQL Text Expansion

  - by noreply(at)blogger.com (Thomas Kyte)

  Here is another small but very useful new feature in Oracle Database 12c - SQL Text Expansion.  It will come in handy in two cases:You are asked to tune what looks like a simple query - maybe a two table join with simple predicates.  But it turns out the two tables are each views of views of views and so on... In other words, you've been asked to 'tune' a 15 page query, not a two liner.You are asked to take a look at a query against tables with VPD (virtual private database) policies.  In order words, you have no idea what you are trying to 'tune'.A new function, EXPAND_SQL_TEXT, in the DBMS_UTILITY package makes seeing what the "real" SQL is quite easy. For example - take the common view ALL_USERS - we can now:ops$tkyte%ORA12CR1> variable x clobops$tkyte%ORA12CR1> begin  2          dbms_utility.expand_sql_text  3          ( input_sql_text => 'select * from all_users',  4            output_sql_text => :x );  5  end;  6  /PL/SQL procedure successfully completed.ops$tkyte%ORA12CR1> print xX--------------------------------------------------------------------------------SELECT "A1"."USERNAME" "USERNAME","A1"."USER_ID" "USER_ID","A1"."CREATED" "CREATED","A1"."COMMON" "COMMON" FROM  (SELECT "A4"."NAME" "USERNAME","A4"."USER#" "USER_ID","A4"."CTIME" "CREATED",DECODE(BITAND("A4"."SPARE1",128),128,'YES','NO') "COMMON" FROM "SYS"."USER$" "A4","SYS"."TS$" "A3","SYS"."TS$" "A2" WHERE "A4"."DATATS#"="A3"."TS#" AND "A4"."TEMPTS#"="A2"."TS#" AND "A4"."TYPE#"=1) "A1"Now it is easy to see what query is really being executed at runtime - regardless of how many views of views you might have.  You can see the expanded text - and that will probably lead you to the conclusion that maybe that 27 table join to 25 tables you don't even care about might better be written as a two table join.Further, if you've ever tried to figure out what a VPD policy might be doing to your SQL, you know it was hard to do at best.  Christian Antognini wrote up a way to sort of see it - but you never get to see the entire SQL statement: http://www.antognini.ch/2010/02/tracing-vpd-predicates/.  But now with this function - it becomes rather trivial to see the expanded SQL - after the VPD has been applied.  We can see this by setting up a small table with a VPD policy ops$tkyte%ORA12CR1> create table my_table  2  (  data        varchar2(30),  3     OWNER       varchar2(30) default USER  4  )  5  /Table created.ops$tkyte%ORA12CR1> create or replace  2  function my_security_function( p_schema in varchar2,  3                                 p_object in varchar2 )  4  return varchar2  5  as  6  begin  7     return 'owner = USER';  8  end;  9  /Function created.ops$tkyte%ORA12CR1> begin  2     dbms_rls.add_policy  3     ( object_schema   => user,  4       object_name     => 'MY_TABLE',  5       policy_name     => 'MY_POLICY',  6       function_schema => user,  7       policy_function => 'My_Security_Function',  8       statement_types => 'select, insert, update, delete' ,  9       update_check    => TRUE ); 10  end; 11  /PL/SQL procedure successfully completed.And then expanding a query against it:ops$tkyte%ORA12CR1> begin  2          dbms_utility.expand_sql_text  3          ( input_sql_text => 'select * from my_table',  4            output_sql_text => :x );  5  end;  6  /PL/SQL procedure successfully completed.ops$tkyte%ORA12CR1> print xX--------------------------------------------------------------------------------SELECT "A1"."DATA" "DATA","A1"."OWNER" "OWNER" FROM  (SELECT "A2"."DATA" "DATA","A2"."OWNER" "OWNER" FROM "OPS$TKYTE"."MY_TABLE" "A2" WHERE "A2"."OWNER"=USER@!) "A1"Not an earth shattering new feature - but extremely useful in certain cases.  I know I'll be using it when someone asks me to look at a query that looks simple but has a twenty page plan associated with it!

  Read the article

• Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

  - by Ritwik

  I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

  Read the article

• CodePlex Daily Summary for Wednesday, September 05, 2012

  CodePlex Daily Summary for Wednesday, September 05, 2012Popular ReleasesDesktop Google Reader: 1.4.6: Sorting feeds alphabetical is now optional (see preferences window)DotNetNuke® Community Edition CMS: 06.02.03: Major Highlights Fixed issue where mailto: links were not working when sending bulk email Fixed issue where uses did not see friendship relationships Problem is in 6.2, which does not show in the Versions Affected list above. Fixed the issue with cascade deletes in comments in CoreMessaging_Notification Fixed UI issue when using a date fields as a required profile property during user registration Fixed error when running the product in debug mode Fixed visibility issue when...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.65: Fixed null-reference error in the build task constructor.BLACK ORANGE: HPAD TEXT EDITOR 0.9 Beta: HOW TO RUN THE TEXT EDITOR Download the HPAD ARCHIVED FILES which is in .rar format Extract using Winrar Make sure that extracted files are in the same folder Double-Click on HPAD.exe application fileTelerikMvcGridCustomBindingHelper: Version 1.0.15.247-RC2: TelerikMvcGridCustomBindingHelper 1.0.15.247 RC2 Release notes: This is a RC version (hopefully the last one), please test and report any error or problem you encounter. This release is all about performance and fixes Support: "Or" and "Does Not contain" filter options Improved BooleanSubstitutes, Custom Aggregates and expressions-to-queryover Add EntityFramework examples in ExampleWebApplication Many other improvements and fixes Fix invalid cast on CustomAggregates Support for ...ServiceMon - Extensible Real-time, Service Monitoring Utility: ServiceMon Release 0.9.0.44: Auto-uploaded from build serverJavaScript Grid: Release 09-05-2012: Release 09-05-2012xUnit.net Contrib: xunitcontrib-dotCover 0.6.1 (dotCover 2.1 beta): xunitcontrib release 0.6.1 for dotCover 2.1 beta This release provides a test runner plugin for dotCover 2.1 beta, targetting all versions of xUnit.net. (See the xUnit.net project to download xUnit.net itself.) This release adds support for running xUnit.net tests to dotCover 2.1 beta's Visual Studio plugin. PLEASE NOTE: You do NOT need this if you also have ReSharper and the existing 0.6.1 release installed. DotCover will use ReSharper's test runners if available. This release includes th...B INI Sharp Library: B INI Sharp Library v1.0.0.0 Realsed: The frist realsedActive Forums for DotNetNuke CMS: Active Forums 5.0.0 RC: RC release of Active Forums 5.0.Droid Explorer: Droid Explorer 0.8.8.7 Beta: Bug in the display icon for apk's, will fix with next release Added fallback icon if unable to get the image/icon from the Cloud Service Removed some stale plugins that were either out dated or incomplete. Added handler for *.ab files for restoring backups Added plugin to create device backups Backups stored in %USERPROFILE%\Android Backups\%DEVICE_ID%\ Added custom folder icon for the android backups directory better error handling for installing an apk bug fixes for the Runn...BI System Monitor: v2.1: Data Audits report and supporting SQL, and SSIS package Environment Overview report enhancements, improving the appearance, addition of data audit finding indicators Note: SQL 2012 version coming soon.The Visual Guide for Building Team Foundation Server 2012 Environments: Version 1: --Nearforums - ASP.NET MVC forum engine: Nearforums v8.5: Version 8.5 of Nearforums, the ASP.NET MVC Forum Engine. New features include: Built-in search engine using Lucene.NET Flood control improvements Notifications improvements: sync option and mail body View Roadmap for more details webdeploy package sha1 checksum: 961aff884a9187b6e8a86d68913cdd31f8deaf83WiX Toolset: WiX Toolset v3.6: WiX Toolset v3.6 introduces the Burn bootstrapper/chaining engine and support for Visual Studio 2012 and .NET Framework 4.5. Other minor functionality includes: WixDependencyExtension supports dependency checking among MSI packages. WixFirewallExtension supports more features of Windows Firewall. WixTagExtension supports Software Id Tagging. WixUtilExtension now supports recursive directory deletion. Melt simplifies pure-WiX patching by extracting .msi package content and updating .w...Iveely Search Engine: Iveely Search Engine （0.2.0）: ????ISE?0.1.0??，?????，ISE?0.2.0?????????，???????，????????20???follow?ISE，????，??ISE??????????，??????????，?????????，?????????0.2.0??????，??????????。 Iveely Search Engine ?0.2.0?????????“??????????”，??????，?????????，???????，???????????????????，????、????????????。???0.1.0????????????： 1. ??“????” ??。??????????，?????????，???????????????????。??：????????，????????????，??????????????????。??????。 2. ??“????”??。?0.1.0??????，???????，???????????????，?????????????，????????，?0.2.0?，???????...GmailDefaultMaker: GmailDefaultMaker 3.0.0.2: Add QQ Mail BugfixSmart Data Access layer: Smart Data access Layer Ver 3: In this version support executing inline query is added. Check Documentation section for detail.DotNetNuke® Form and List: 06.00.04: DotNetNuke Form and List 06.00.04 Don't forget to backup your installation before upgrade. Changes in 06.00.04 Fix: Sql Scripts for 6.003 missed object qualifiers within stored procedures Fix: added missing resource "cmdCancel.Text" in form.ascx.resx Changes in 06.00.03 Fix: MakeThumbnail was broken if the application pool was configured to .Net 4 Change: Data is now stored in nvarchar(max) instead of ntext Changes in 06.00.02 The scripts are now compatible with SQL Azure, tested in a ne...Coevery - Free CRM: Coevery 1.0.0.24: Add a sample database, and installation instructions.New ProjectsA Simple Eng-Hindi CMS: A simple English- Hindi dual language content management system for small business/personal websites.Active Social Migrator: This project for managing the Active Social migration tool.ANSI Console User Control: Custom console control for .NET WinformsAutoSPInstallerGUI: GUI Configuration Tool for SPAutoInstaller Codeplex ProjectCode Documentation Checkin Policy: This checkin policy for Visual Studio 2012 checks if c# code is documented the way it's configured in the config of the policy. Code Dojo/Kata - Free Time Coding: Doing some katas of the Coding Dojo page. http://codingdojo.org/cgi-bin/wiki.pl?KataCataloguefjycUnifyShow: fjycUnifyShowHidden Capture (HC): HC is simple and easy utility to hidden and auto capture desktop or active windowHRC Integration Services: Fake SQL Server Integration Services. LOLKooboo CMS Sites Switcher: Kooboo CMS Sites SwitcherMod.CookieDetector: Orchard module for detecting whether cookies are enabledMyCodes: Created!MySQL Statement Monitor: MySQL Statement Monitor is a monitoring tool that monitors SQL statements transferred over the network.NeoModulusPIRandom: The idea with PI Random is to use easy string manipulation and simple math to generate a pseudo random number. Net Core Tech - Medical Record System: This is a Medical Record System ProjectOraPowerShell: PowerShell library for backup and maintenance of a Oracle Database environment under Microsoft Windows 2008PinDNN: PinDNN is a module that imparts Pinterest-like functionality to DotNetNuke sites. This module works with a MongoDB database and uses the built-in social relatioPyrogen Code Generator: PyroGen is a simple code generator accepting C# as the markup language.restMs: wil be deleted soonScript.NET: Script.NET is a script management utility for web forms and MVC, using ScriptJS-like features to link dependencies between scripts.SpringExample-Pagination: Simple Spring example with PaginationXNA and Component Based Design: This project includes code for XNA and Component Based Design

  Read the article

• Can't get the L2TP IPSEC up and running

  - by Maciej Swic

  i have an Ubuntu 11.10 (oneiric) server running on a ReadyNAS. Im planning to use this to accept ipsec+l2tp connections through a router. However, the connection is failing somewhere half through. Using Openswan IPsec U2.6.28/K3.0.0-12-generic and trying to connect with an iOS 5 iPhone 4S. This is how far i can get: auth.log: Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "PSK" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-NAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-noNAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "passthrough-for-non-l2tp" Jan 19 13:54:11 ubuntu pluto[1990]: listening for IKE messages Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying new style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying old style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo ::1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 2001:470:28:81:a00:27ff:* Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/etc/ipsec.secrets" Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/var/lib/openswan/ipsec.secrets.inc" Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [Dead Peer Detection] Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: responding to Main Mode from unknown peer 95.*.*.233 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R1: sent MR1, expecting MI2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R2: sent MR2, expecting MI3 Jan 19 14:05:03 ubuntu pluto[1990]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 95.*.*.233 port 500, complainant 95.*.*.233: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Router config UDP 500, 1701 and 4500 forwarded to 192.168.19.99 (Ubuntu server for ipsec). Ipsec passthrough enabled. /etc/ipsec.conf # /etc/ipsec.conf - Openswan IPsec configuration file # This file: /usr/share/doc/openswan/ipsec.conf-sample # # Manual: ipsec.conf.5 version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes #charonstart=yes #plutostart=yes protostack=netkey conn PSK authby=secret forceencaps=yes pfs=no auto=add keyingtries=3 dpdtimeout=60 dpdaction=clear rekey=no left=192.168.19.99 leftnexthop=192.168.19.1 leftprotoport=17/1701 right=%any rightprotoport=17/%any rightsubnet=vhost:%priv,%no dpddelay=10 #dpdtimeout=10 #dpdaction=clear include /etc/ipsec.d/l2tp-psk.conf /etc/ipsec.d/l2tp-psk.conf conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT # # PreSharedSecret needs to be specified in /etc/ipsec.secrets as # YourIPAddress %any: "sharedsecret" authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=192.168.19.99 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "0" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port, but propose "0" instead of their port. rightprotoport=17/%any dpddelay=10 dpdtimeout=10 dpdaction=clear conn passthrough-for-non-l2tp type=passthrough left=192.168.19.99 leftnexthop=192.168.19.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/ipsec.secrets include /var/lib/openswan/ipsec.secrets.inc %any %any: PSK "my-key" 192.168.19.99 %any: PSK "my-key" /etc/xl2tpd/xl2tpd.conf [global] debug network = yes debug tunnel = yes ipsec saref = no listen-addr = 192.168.19.99 [lns default] ip range = 192.168.19.201-192.168.19.220 local ip = 192.168.19.99 require chap = yes refuse chap = no refuse pap = no require authentication = no ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd pcp-accept-local ipcp-accept-remote noccp auth crtscts idle 1800 mtu 1410 mru 1410 defaultroute debug lock proxyarp connect-delay 5000 ipcp-accept-local /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses maciekish * my-secret * * maciekish my-secret * I can't seem to find the problem. Other ipsec connections to other hosts work from the network im currently at.

  Read the article

• Need help trouble shooting high CPU usage by PHP-fpm

  - by user432506

  There is a problem that is driving me crazy. After the day I tried to fix the CPU usage problem of my VPS, the CPU load has grown from 60% to 150%, and I have no idea what causes the problem. Please help me. I had installed a copy of mediawiki on a Linode 1024. The wiki is running on Niginx + PHP-fpm + MySql. The wiki doesn't have much traffic, only around 4000 requests/day, mostly from Google and Bing bots. It had been using around 60% (of total 400% on the Linode) of the CPU before. I thought it was a bit high, so two day ago, I was trying to fix the problem (not knowing what was waiting for me). I did nothing but added a new empty line to wiki's configure file, which would change the modified time of the configure file, and then all the cached page files would be set invalidated. I had done that before, and that would cause high CPU usage, but normally it would take only hours to let things back to normal again. Not this time, my CPU usage has been around 150% for more than two days. It is php-fpm using most of CPU reassures. Using 100% of three cores is not rare. I hadn't seen that before. There are other sites on the Linode, but it should be the wiki. Because if I offline the wiki, CPU usage will drop back to around 40% soon. The day I also duplicated php-fpm.conf, and opened it, but didn't changed it. I have no idea what I did wrong. I here ask for help to save myself from being crazy!!! It is php-fpm. Is there a way to find out what is it doing? I mean like which scripts are related and what function codes are running? top: top - 06:34:33 up 10 days, 4:23, 2 users, load average: 1.10, 1.24, 1.37 Tasks: 76 total, 4 running, 72 sleeping, 0 stopped, 0 zombie Cpu(s): 61.1%us, 3.1%sy, 0.0%ni, 32.8%id, 2.9%wa, 0.0%hi, 0.0%si, 0.1%st Mem: 1028684k total, 945192k used, 83492k free, 89580k buffers Swap: 524284k total, 18084k used, 506200k free, 530380k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 26721 www-data 20 0 208m 54m 34m R 99 5.4 0:09.07 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26592 www-data 20 0 207m 45m 26m R 91 4.5 0:12.77 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26706 www-data 20 0 196m 43m 34m S 47 4.3 0:15.19 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26583 www-data 20 0 197m 45m 35m S 33 4.5 0:19.08 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26787 www-data 20 0 206m 36m 18m R 25 3.7 0:00.41 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 26661 www-data 20 0 207m 46m 26m S 13 4.6 0:19.87 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 1971 mysql 20 0 155m 57m 3952 S 8 5.7 383:57.81 /usr/sbin/mysqld 242 root 20 0 0 0 0 S 1 0.0 0:51.36 [kworker/3:1] 5711 root 20 0 139m 95m 580 S 1 9.5 0:41.30 /usr/local/bin/memcached -d -u root -m 128 -p 11211 19463 root 20 0 190m 3984 1284 S 1 0.4 0:02.66 /opt/php5/sbin/php-fpm --fpm-config /opt/php5/etc/php-fpm.conf 29100 www-data 20 0 10928 5540 820 S 1 0.5 4:49.05 nginx: worker process vmstat 30 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 16912 81456 90784 554172 0 0 4 6 3 2 11 1 87 1 0 0 16912 78036 91000 555356 0 0 38 34 1397 375 12 1 87 0 4 0 16912 31776 91528 557508 0 0 78 42 3197 487 45 1 52 1 1 0 16912 83356 91768 558576 0 0 35 56 2608 449 32 1 67 1 1 0 16912 81548 92040 559720 0 0 41 31 1243 432 8 1 91 1 2 0 16912 53056 92332 562744 0 0 105 33 2013 581 17 1 81 1 2 0 16912 73236 92552 564844 0 0 68 36 1968 615 16 1 82 1 0 0 16912 91612 92904 566676 0 0 69 35 1845 692 13 1 85 1 1 0 16912 71248 93180 568428 0 0 58 33 1952 604 15 1 82 1 1 0 16868 55952 93516 572660 1 0 144 42 1801 637 12 1 86 1 2 0 16868 48324 94416 577844 0 0 189 66 2058 702 17 1 80 2 1 0 16928 58644 94592 578184 0 2 160 49 2578 723 25 1 70 3 5 0 16928 22600 94980 580568 0 0 89 32 1496 361 13 0 85 1 0 0 16988 49256 94500 576396 0 2 41 37 1601 426 14 1 85 0 5 0 18084 24336 86032 502748 0 37 83 68 2989 562 42 1 56 0 1 0 18084 123604 86376 506996 0 0 118 41 2201 573 22 1 76 1 2 0 18084 126984 86752 508876 0 0 64 53 1620 490 13 1 85 1 2 0 18084 103104 87148 510768 0 0 71 37 2757 602 33 1 64 1

  Read the article

• Windows XP Domain Logon takes between 40 - 60 minutes

  - by Bryan

  Windows XP Clients, fully patched, with Symantec Endpoint Protection 11 client Windows 2008 R2 domain Roaming profiles Folder Redirection applied to Documents, AppData & Desktop I've enabled userenv logging, and logged on just after 17:00 last night. The user shell hadn't appeared at 17:45 when I left last night. When I arrived this morning, I checked the log file and found the following. USERENV(3f8.e7c) 17:02:18:296 LogExtSessionStatus: Successfully logged Extension Session data USERENV(654.a30) 17:04:09:468 ImpersonateUser: Failed to impersonate user with 5. USERENV(654.a30) 17:04:09:468 GetUserNameAndDomain Failed to impersonate user USERENV(654.a30) 17:04:09:468 GetUserDNSDomainName: Domain name is NT Authority. No DNS domain name available. USERENV(c8c.cb8) 17:04:09:781 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(cd0.cd4) 17:04:10:781 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(d08.c84) 17:07:09:609 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(cbc.cc0) 17:07:10:625 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\luall.exe USERENV(db0.db4) 17:07:10:781 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(e00.e0c) 17:07:11:062 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(e20.e34) 17:07:11:203 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(e40.e50) 17:07:11:406 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(efc.54c) 17:07:11:656 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(ccc.df0) 17:08:45:687 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(e24.e20) 17:08:45:937 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\luall.exe USERENV(ff0.ff4) 17:08:46:078 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(32c.cd0) 17:08:46:265 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(cc4.3d4) 17:08:46:406 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(434.4d0) 17:08:46:593 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(f2c.ac) 17:08:46:828 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(d60.d7c) 17:09:40:265 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(d94.d98) 17:09:40:531 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(bc4.3c4) 17:10:52:765 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(37c.90c) 17:10:52:984 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\luall.exe USERENV(580.540) 17:10:53:109 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(c18.c30) 17:10:53:312 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(c44.288) 17:10:53:468 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(a34.cf4) 17:10:53:656 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(d3c.d4c) 17:10:53:890 LibMain: Process Name: C:\Program Files\Symantec\LiveUpdate\LuCallbackProxy.exe USERENV(970.948) 17:15:09:468 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(150.9dc) 17:15:09:734 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(f90.cec) 17:20:38:718 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(d8c.d70) 17:20:38:984 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(9a0.fa0) 17:26:07:953 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(844.51c) 17:26:08:218 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(d00.9ac) 17:31:19:453 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(ad4.624) 17:31:19:718 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(654.694) 17:31:46:390 ImpersonateUser: Failed to impersonate user with 5. USERENV(654.694) 17:31:46:390 GetUserNameAndDomain Failed to impersonate user USERENV(654.694) 17:31:46:390 GetUserDNSDomainName: Domain name is NT Authority. No DNS domain name available. USERENV(af8.610) 17:36:48:625 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(aa4.dfc) 17:36:48:906 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(2dc.5c8) 17:42:17:812 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(f70.8ac) 17:42:18:078 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(d50.c30) 17:47:47:062 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(c2c.c3c) 17:47:47:328 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(ef0.4cc) 17:53:16:234 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(cd4.c84) 17:53:16:500 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE USERENV(828.8c4) 17:58:45:484 LibMain: Process Name: C:\Program Files\Symantec\Symantec Endpoint Protection\SescLU.exe USERENV(a24.b30) 17:58:45:750 LibMain: Process Name: C:\PROGRA~1\Symantec\LIVEUP~1\LUCOMS~1.EXE I've seen posts suggesting that it may be Windows Desktop Search 3.01 that is causing this, so I've removed that. I've removed the policy, 'Always wait for the network at startup or logon', thinking that might have helped. I'm running out of ideas. Has anyone seen this before?

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >