Search Results

Search found 18833 results on 754 pages for 'c link nepal'.

Page 92/754 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Unable to keep the connecting using a wireless bridge

  - by dan

  I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• JQuery tools.scrollable conflict with navbar Ajax in CakePHP

  - by user269098

  In our views/layout/default.ctp file we have an element that's used to implement a cascading combo select box which uses JQuery ajax to update the fields. This selector is part of our navbar and is loaded on every page of the site. The default.ctp has these includes in the : <?php echo $html->charset(); ?> <title><?php echo $title_for_layout; //if(Configure::read('debug')) //echo "cake: " . Configure::version(); ?></title> <?php echo $html->css('style'); echo $javascript->link('jquery', true); echo $javascript->link('jquery.form', true); echo $javascript->link('jquery.url', true); echo $javascript->link('navbar', true); echo $html->script('tools.expose-1.0.3.js', array('inline' => false)); //echo $scripts_for_layout; ?> On the views/cars/index.ctp page we have: echo $javascript->link('tools.tabs-1.0.1', true); echo $javascript->link('tools.overlay-1.0.4', true); echo $javascript->link('jquery.form', true); echo $javascript->link('tools.scrollable-1.0.5', true); The issue is that on every other page the navbar combo box selector works. However, on the cars/index.ctp it doesn't work. It only works when we comment out the 'tools.scrollable' include. Any ideas why there is this conflict? We have been stuck on this problem for months...

  Read the article

• How can I programmatically link an UIView or UIImageView with an event like "touch up inside"?

  - by Thanks

  Interface Builder will only allow me to hook up such events for an button. But like in HTML, I just want to haven an blank UIImageView where - as soon as the user taps it - a method is invoked. I hope there is some cool programmatically way of doing that, which I don't know about. UPDATE: In my View Controller that creates the UIImageView I tried to do this: SEL actionSelector = @selector(doSomethingWhenImageIsTouched:); [self.myUIImageView addTarget:nil action:actionSelector forControlEvents:UIControlEventTouchUpInside]; The compiler gives me a warning, that UIImageView may not respond to addTarget:... what do I have to do so that it works with an UIImageView. I see in the docs that UIImageView does not inherit from UIControl, but addTarget: is part of UIControl. UPDATE: I ended up creating an UIButton after creating the UIImageView. Then I set the frame of that button to the frame of the UIImageView, and alpha to 0.1f. For some reason, it will not work if alpha is 0.0f. And then, I did that cool addTarget: thing...

  Read the article

• When trying to include '#include <boost/regex.hpp>' I get: 1>LINK : fatal error LNK1104: cannot open

  - by meds

  Not sure why i get that, I downloaded libs from here and while I have a lib called 'libboost_regex-vc90-mt-gd-1_39.lib I don't have one which is called 'libboost_regex-vc100-mt-gd-1_39.lib', renaming the one with vc90 to vc100 works but I'm not sure if this is the ideal solution?

  Read the article

• How to close window in ie using link and onbeforeunload?

  - by Salil

  Hi All, I open a pop-up window using following code in main.html function openwindow(url) { window.open(url, "mywindow","location=1,status=1,scrollbars=1,resizable=no,width=650,height=650"); } Open In My child.html i used function closewindow() { self.close(); } function closeIt() { return "Your chat will be terminated. Are you sure?" } < a href="javascript:void(0)" onclick="closewindow();"Close Window< /a     When i click on close window it gize me alert message that i given on event onbeforeunload but it not close the window when i click on Ok.Also this happens only in I.E. & working fine in mozilla, netscape, safari. I checked it on IE6 & IE8 Any help is Appreciated. Regards, Salil Gaikwad

  Read the article

• How do I display field when I click on a link? (javascript)

  - by ggfan

  how do I create it so that when I click "report user", a box displays and it shows a list of reasons why to report the user and a submit button. I rarely use javascript...can someone point me in the right direction.

  Read the article

• Route forwarded traffic through eth0 but local traffic through tun0

  - by Ross Patterson

  I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

  Read the article

• How to link a SQlite Extension Source File into Xcode for iPhone?

  - by crunchyt

  I use a statically linked library for Sqlite in an iPhone Xcode project. I am now trying to include a .C extension to Sqlite in this project. However, I am having trouble making the Sqlite in the build SEE the extension. The statically linked Sqlite library works fine. Also the .C extension works on my desktop, and builds fine as a statically linked library in Xcode. However, the custom functions it defines are missing when called. For example, I load the extension as so with no errors. SELECT load_extension('extension_name.so'); But when I try to call a function defined in the extension, I get this message DB Error: 1 "no such function: custom_function" Does anyone know much about linking a Sqlite extension into an Xcode project?

  Read the article

• xp_smtp_sendmail blank space added to html randomly

  - by Igor Timofeyev

  I have a proc where I generate small html doc with a link and send it out via xp_smtp_sendmail proc. Link is generated based on query results and is long. This works in most cases. However, sometimes the link gets broken due to spaces being inserted into querystring variable names, i.e. &Na me=John. This might vary between email clients(same link works in Gmail, but might not work in comcast due to spaces. The space seems to be randomly inserted, so in each broken email link space might break other querystring variables. When I do PRINT from proc the link is clean, no spaces. Here's my sample of the mail proc being executed within main proc(that gets query results and generates html for @Message). The space seems to be inserted regardless of whether I encode the url or not. Thank you in advance for your help. I can send a cleaner version of the code if it's not displayed properly here. ....query results above SET @Message = NULL SET @Message = @Message + + '<br/>Dear ' + @FirstName + ' ' + @LastName + ',' + '<br/><br/>Recently you took "' + @Title + '". ' + 'In response to the question "What is it?" ' + 'you responded "' + @Response + '".' + '<br/><br/>Following up on previous mailing' + '<br/><br/>Please click on the link below' + '<br/><br/><a href="' + @Link + '">Please click here</a>' + '<br/><br/>plain text' + '<br/><br/>plain text,' + '<br/><br/>plain text<br/> plain text<br/> plain text<br/> plain text<br/> plain text<br/> plain text EXEC @rc = master.dbo.xp_smtp_sendmail @FROM = '[email protected]', @FROM_NAME = 'Any User', @TO = @Email, @priority = N'NORMAL', @subject = N'My email', @message = @Message, @messagefile = N'', @type = N'text/html', @attachment = N'', @attachments = N'', @codepage = 0, @server = 'smtp.server.any'

  Read the article

• How come my email link in drupal footer message doesn't work?

  - by Behrooz Karjooravary

  This is what I have typed in the footer message section from the site configuration, sight information page: Copyright Sage 2010 | Contact Us: < a ="mailto:[email protected]" [email protected]< / a | < a="www.mysite.org/contactoptions" other contact options< / a However, when i click on the links nothing happens. I was told all I need to do is set input format to 'Full HTML' in drupal to make that work. But it still doesn't work.

  Read the article

• How many javascript link I can have in Facebook?

  - by Murvinlai

  Is there a limit of how many js file I can include () in facebook? I include 5 files. no problem.. the 6th one not loaded. Then I have to put the code in the 6th one into the 5th file. then works. so, is it 5 files in max? BY THE WAY, I'm developing the apps now, not in production. so it is not in the stage of compressing JS / minizing it. :) so it is kinda annoying to got missing js files or files not loaded..etc so, what is the limit from FB? what is the file size limit? I know that the JSON request call back data limit is 5000.. but not sure about the js include.

  Read the article

• Routing data through VPN in linux

  - by Shadyabhi

  I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

  Read the article

• Why modules link is not coming on Administrator Main page?

  - by Nitz

  I have added two modules in my drupal site called.... 1. me alias 2. Mime mail Whenever we add new modules to our site, it has links on admin page. but after activating modules, i can't see the links on admin page. but this happens only on server but on my localhost i can see the modules links on admin page. i have put screenshot of the problem, in image you can see that, i have activated both modules but on admin page....i can't see its links. why is not activated. i have tried to clear all the cache and then try again but its not coming then also. Here is the screen shot

  Read the article

• Where is the latest link Eric meyer's reset? and pls explain his reset.

  - by metal-gear-solid

  How many version are eric meyer created of his CSS reset and where is latest and what is difference in each version? and please explain his CSS reset's each declaration, What is the benefit of each selector?

  Read the article

• Create a many to many relationship in Entity Framework skipping extra data in the link table.

  - by Paul Smith

  I would like to model the following many to many relationship. Table A ID Field1 Field2 Table B ID Field1 Field2 LinkTable A_ID B_ID Field_I_want_to_ignore As I understand it, if LinkTable.Field_I_want_to_ignore was not present, the Entity Model Designer would automatically create a Many to Many relationship between entity A and entity B. However, because this field exists in the database the designer won't do it for me. I can delete the Field_I_want_to_ignore from the LinkTable Entity that the designer created for me, but how do I eliminate the LinkTable entity altogether and create the many to many relationship I want? I'm not averse to digging through the XML, just at the moment I can't see how to achieve what I want.

  Read the article

• How do you make hovering over a link produce a sound.

  - by Behrooz Karjooravary

  I have a client who requested piano keys as links and he wants them to sound when the mouse hovers over the keys. How can this be done without using flash?

  Read the article

• Hibernate: How do I link a subclass to its superclass?

  - by Markus

  Hey there! I'm having a little problem setting up my webshop project. Thing is, I have a User() superclass and two subclasses, PrivateUser and BusinessUser. Now, I'm not quite sure how to get my head around storing this relationship via hibernate. For the purpose of this question, the User() class contains only one field: String address; the PrivateUser contains: String firstName; and the BusinessUser contains: String CompanyName; Each field has its getter and setter. As is right now, I would only store and be able to get firstName and companyName. When I fetch a user from my DB using Hibernate I would get a PrivateUser/BusinessUser with a null address. Bottom line is, could someone point me towards a useful tutorial or better yet show a similar example code? Thanks!

  Read the article

• Matching a Repeating Sub Series using a Regular Expression with PowerShell

  - by Hinch

  I have a text file that lists the names of a large number of Excel spreadsheets, and the names of the files that are linked to from the spreadsheets. In simplified form it looks like this: "Parent File1.xls" Link: ChildFileA.xls Link: ChildFileB.xls "ParentFile2.xls" "ParentFile3.xls" Blah Link: ChildFileC.xls Link: ChildFileD.xls More Junk Link: ChildFileE.xls "Parent File4.xls" Link: ChildFileF.xls In this example, ParentFile1.xls has embedded links to ChildFileA.xls and ChildFileB.xls, ParentFile2.xls has no embedded links, and ParentFile3.xls has 3 embedded links. I am trying to write a regular expression in PowerShell that will parse the text file producing output in the following form: ParentFile1.xls:ChildFileA.xls,ChildFileB.xls ParentFile3.xls:ChildFileC.xls,ChildFileD.xls,ChildFileE.xls etc The task is complicated by the fact that the text file contains a lot of junk between each of the lines, and a parent may not always have a child. Furthermore, a single file name may pass over multiple lines. However, it's not as bad as it sounds, as the parent and child file names are always clearly demarcated (the parent with quotes and the child with a prefix of Link: ). The PowerShell code I've been using is as follows: $content = [string]::Join([environment]::NewLine, (Get-Content C:\Temp\text.txt)) $regex = [regex]'(?im)\s*\"(.*)\r?\n?\s*(.*)\"[\s\S]*?Link: (.*)\r?\n?' $regex.Matches($content) | %{$_.Groups[1].Value + $_.Groups[2].Value + ":" + $_.Groups[3].Value} Using the example above, it outputs: ParentFile1.xls:ChildFileA.xls ParentFile2.xls""ParentFile3.xls:ChildFileC.xls ParentFile4.xls:ChildFileF.xls There are two issues. Firstly, the inclusion of the "" instead of a newline whenever a Parent without a Child is processed. And the second issue, which is the most important, is that only a single child is ever shown for each parent. I'm guessing I need to somehow recursively capture and display the multiple child links that exist for each parent, but I'm totally stumped as to how to do this with a regular expression. Amy help would be greatly appreciated. The file contains 100's of thousands of lines, and manual processing is not an option :)

  Read the article

• My pay pal button will not link to pay pal. It only refreshes page, why?

  - by JPJedi

  I have the following code in my registration page to go to a paypal button. But when I click on the button it just refreshes the page. Is their something I am missing? I should be able to include a paypal button on an aspx page right? <asp:Content ID="Content1" ContentPlaceHolderID="head" Runat="Server"> </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="ContentPlaceHolder1" Runat="Server"> <asp:Panel runat="server" ID="pnlRegisterPage" CssClass="registerPage"> <table> <tr> <td><p>Plain text</p></td> <td> <form action="https://www.paypal.com/cgi-bin/webscr" method="post"> <input type="hidden" name="cmd" value="_s-xclick"> <input type="hidden" name="hosted_button_id" value="Z8TACKRHQR722"> <table> <tr><td><input type="hidden" name="on0" value="Registration Type">Registration Type</td></tr><tr><td><select name="os0"> <option value="Team">Team $80.00</option> <option value="Individual">Individual $40.00</option> </select> </td></tr> </table> <input type="hidden" name="currency_code" value="USD"> <input type="image" src="https://www.paypal.com/en_US/i/btn/btn_buynowCC_LG.gif" border="0" name="submit" alt="PayPal - The safer, easier way to pay online!"> <img alt="" border="0" src="https://www.paypal.com/en_US/i/scr/pixel.gif" width="1" height="1"> </form> </td> </tr> </table> </asp:Panel> </asp:Content> Master Page <body> <form id="form1" runat="server"> <asp:ToolkitScriptManager ID="ToolkitScriptManager1" runat="server"> </asp:ToolkitScriptManager> <div class="masterbody"> <center> <asp:Image runat="server" ID="imgLogo" ImageUrl="" /></center> <div class="menubar"> <div class="loginview"> <asp:LoginView ID="MenuBar" runat="server"> <AnonymousTemplate> </AnonymousTemplate> <LoggedInTemplate> </LoggedInTemplate> </asp:LoginView> </div> </div> <div> <asp:ContentPlaceHolder ID="ContentPlaceHolder1" runat="server"> </asp:ContentPlaceHolder> </div> </div> <div class="footer"></div> </form> </body>

  Read the article

• How do you link to an action that takes an array as a parameter (RedirectToAction and/or ActionLink)

  - by Andrew

  I have an action defined like so: public ActionResult Foo(int[] bar) { ... } Url's like this will work as expected: .../Controller/Foo?bar=1&bar=3&bar=5 I have another action that does some work and then redirects to the Foo action above for some computed values of bar. Is there a simple way of specifying the route values with RedirectToAction or ActionLink so that the url's get generated like the above example? These don't seem to work: return RedirectToAction("Foo", new { bar = new[] { 1, 3, 5 } }); return RedirectToAction("Foo", new[] { 1, 3, 5 }); <%= Html.ActionLink("Foo", "Foo", new { bar = new[] { 1, 3, 5 } }) %> <%= Html.ActionLink("Foo", "Foo", new[] { 1, 3, 5 }) %> However, for a single item in the array, these do work: return RedirectToAction("Foo", new { bar = 1 }); <%= Html.ActionLink("Foo", "Foo", new { bar = 1 }) %> When setting bar to an array, it redirects to the following: .../Controller/Foo?a=System.Int32[] Finally, this is with ASP.NET MVC 2 RC. Thanks.

  Read the article

• add target="_blank" to all link with a certain a div.

  - by kakkalo

  so lets say i got these following codes <div id="link_other"> <ul> <li><a href="http://www.google.com/">google</a></li> <li><div class="some_class">dsalkfnm sladkfm <a href="http://www.yahoo.com/">yahoo</a></div> </li> </ul> </div> so in this case script will add target="_blank" to all links within "link_other" div. how can i do that? thank you

  Read the article

• Possible to link an image in a playlist to a URL, with Flowplayer?

  - by Yegor

  I have a simple Flowplayer playlist. First one plays a short clip, which then cuts off, and an image is displayed. Is there a way to make the image clickable? here is what I have: <a style="display:block;width:640px;height:360px" id="player"> </a> <script> flowplayer("player", "../flowplayer-3.1.5.swf", { playlist: [ {url: 'http://e1h13.simplecdn.net/flowplayer/flowplayer.flv', duration: 10}, {url: 'http://www.domain.com/image.jpg', duration: 100000}, ], plugins: { controls: null } }); </script> If there is another way of doing this, Im all ears. I need a video to play for 10 seconds (or entirely, since the file is gonna be 10 seconds long), and then display some text + a URL.

  Read the article

• How do link the first level like localhost/About and localhost/Faq.

  - by alex

  I make Views/About/Index.aspx and Views/Faq/Index.aspx + Controllers/AboutController.cs and Controllers/FaqController.cs controllers for these purposes. I want to have one controller Controllers/DefaultController.cs + Views/About.aspx and Views/Faq.aspx in the root, for example. How to set it up?

  Read the article

• How does Wordpress link posts to categories in its database?

  - by bcmcfc

  At present I am displaying a list of the last 5 posts in a site's blog in its footer using this mysql query: SELECT post_title, guid, post_date FROM wp_posts WHERE post_type = 'post' AND post_status = 'Publish' ORDER BY post_date DESC LIMIT 5 How can I edit this query to restrict the search to a particular category id? I thought it would be as simple as looking for a category field in the posts table but it isn't!

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >