Search Results

Search found 47251 results on 1891 pages for 'web storage'.

Page 921/1891 | < Previous Page | 917 918 919 920 921 922 923 924 925 926 927 928  | Next Page >

• Secondary Domain Adds Extra Folder in URL during Postbacks

  - by Joshua

  My ASP.NET Website (C#, 3.5 framework, IIS7) is hosted at GoDaddy. There are multiple sites on the account. Currently when I perform postbacks or Response.Redirects on a secondary web site, the following URL appears in the address bar: www.mywebsite.com/webfolder/default.aspx Where the "webfolder" is the sub-directory on the server where the web site is hosted (i.e. SeverRoot/webfolder). The site seems to work with or without the folder in the URL. Is there a way to remove the folder from the URLs during postback? I think I have to use URL Rewriting (which GoDaddy supports using Microsoft's Rewrite Module) but I'm not sure how.

  Read the article

• What are the best options for a root filesystem hosted on SSD under Linux

  - by stsquad

  I'm working on an embedded system which is going to be booting and hosting it's rootfs on an SSD disk. We are currently looking at using Intel X-18M SSDs. The file system structure will have a fairly static /usr section (modulo software upgrades) and an active /var and /var/log for maintaining state and logging. Given the wear-levelling done by the underlying flash does having separate partitions help or hinder? As modern SSDs appear as straight block devices and hide their mapping magic behind their firmware is there any point trying to optimise the choice of file-system that sits on-top of the SSD? Finally does enable SMART monitoring make any sense in this context or are their SSD specific ways of determining the underlying health of the storage hardware?

  Read the article

• Exception when ASP.NET attempts to delete network file.

  - by Jordan Terrell

  Greetings - I've got an ASP.NET application that is trying to delete a file on a network share. The ASP.NET application's worker process is running under a domain account (confirmed this by looking in TaskManager and by using ShowContexts2.aspx¹). I've been assured by the network admins that the process account is a member of a group that has Modify permissions to the directory that contains the file I'm trying to delete. However, it is unable to do so, and instead I get an exception (changed the file path to all x's): System.Web.HttpUnhandledException: Exception of type 'System.Web.HttpUnhandledException' was thrown. --- System.UnauthorizedAccessException: Access to the path '\xxxxxxx\xxxxxxx\xxxxxxx\xxxxxx.xxx' is denied. Any ideas on how to diagnose/fix this issue? Thanks - Jordan ¹ http://www.leastprivilege.com/ShowContextsNET20Version.aspx

  Read the article

• Function to hide sloppy phone numbers..

  - by Frank Malina

  I need to hide phone numbers (and maybe other contact details) in user generated content to protect my users from anonymous web. Input is very random, therefore I'd be looking to replace anything that looks like a phone number (e.g.: string of 3 or more numbers) with just dots, and also perhaps remove some exotic notations of e-mail addresses. What is the best way to do this? Nice and slick, reusable. Give away your secret regexes. Write in any language. Except perhaps COBOL :) function privacy($str){ // protect phone numbers // protect e-mail addresses // protect web addresses }

  Read the article

• How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

  - by atticus

  I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83.

  Read the article

• Updating a deallocated UIWebView from a background thread

  - by Dan Ray

  As you can see from the title, I've programmed myself into a corner and I've got several things working against me... In a UIViewController subclass that manages a large and complex view. One part of it is a UIWebView that contains output from a web request that I had to build and execute, and manually assemble HTML from. Since it takes a second or two to run, I dropped it into the background by calling self performSelectorInBackground:. Then from that method I call there, I use self performSelectorOnMainThread: to get back to the surface of the thread stack to update the UIWebView with what I just got. Like this (which I've cut down to show only the relevant issues): -(void)locationManager:(CLLocationManager *)manager didUpdateToLocation:(CLLocation *)newLocation fromLocation:(CLLocation *)oldLocation { //then get mapquest directions NSLog(@"Got called to handle new location!"); [manager stopUpdatingLocation]; [self performSelectorInBackground:@selector(getDirectionsFromHere:) withObject:newLocation]; } - (void)getDirectionsFromHere:(CLLocation *)newLocation { NSAutoreleasePool *pool = [[NSAutoreleasePool alloc] init]; CLLocationCoordinate2D here = newLocation.coordinate; // assemble a call to the MapQuest directions API in NSString *dirURL // ...cut for brevity NSLog(@"Query is %@", dirURL); NSString *response = [NSString stringWithContentsOfURL:[NSURL URLWithString:dirURL] encoding:NSUTF8StringEncoding error:NULL]; NSMutableString *directionsOutput = [[NSMutableString alloc] init]; // assemble response into an HTML table in NSString *directionsOutput // ...cut for brevity [self performSelectorOnMainThread:@selector(updateDirectionsWithHtml:) withObject:directionsOutput waitUntilDone:NO]; [directionsOutput release]; [pool drain]; [pool release]; } - (void)updateDirectionsWithHtml:(NSString *)directionsOutput { [self.directionsWebView loadHTMLString:directionsOutput baseURL:nil]; } This all works totally great, UNLESS I've backed out of this view controller before CLLocationManager hits its delegate method. If this happens after I've already left this view, I get: 2010-06-07 16:38:08.508 EverWondr[180:760b] bool _WebTryThreadLock(bool), 0x1b6830: Tried to obtain the web lock from a thread other than the main thread or the web thread. This may be a result of calling to UIKit from a secondary thread. Crashing now... Despite what this says, I can repeatably cause this crash when I back out too early. I'm not at all convinced that attempting a UI update from a background thread is really the issue; I think it's that my UIWebView is deallocated. I suspect that the fact I was just IN a background thread makes the runtime suspect something's up about that, but I feel fairly sure that's not it. So how do I tell CLLocationManager not to worry about it, when I'm backing out of that view? I tried [self.locationManager stopUpdatingLocation] inside my viewWillDisappear method, but that didn't do it. (Incidentally, MapQuest's apis are FANTASTIC. Way WAY better than anything Google provides. I can't recommend them highly enough.)

  Read the article

• ASP.NET Client to Server communication

  - by Nelson

  Can you help me make sense of all the different ways to communicate from browser to client in ASP.NET? I have made this a community wiki so feel free to edit my post to improve it. Specifically, I'm trying to understand in which scenario to use each one by listing how each works. I'm a little fuzzy on UpdatePanel vs CallBack (with ViewState): I know UpdatePanel always returns HTML while CallBack can return JSON. Any other major differences? ...and CallBack (without ViewState) vs WebMethod. CallBack goes through most of the Page lifecycle, WebMethod doesn't. Any other major differences? IHttpHandler Custom handler for anything (page, image, etc.) Only does what you tell it to do (light server processing) Page is an implementation of IHttpHandler If you don't need what Page provides, create a custom IHttpHandler If you are using Page but overriding Render() and not generating HTML, you probably can do it with a custom IHttpHandler (e.g. writing binary data such as images) By default can use the .axd or .ashx file extensions -- both are functionally similar .ashx doesn't have any built-in endpoints, so it's preferred by convention Regular PostBack (System.Web.UI.Page : IHttpHandler) Inherits Page Full PostBack, including ViewState and HTML control values (heavy traffic) Full Page lifecycle (heavy server processing) No JavaScript required Webpage flickers/scrolls since everything is reloaded in browser Returns full page HTML (heavy traffic) UpdatePanel (Control) Control inside Page Full PostBack, including ViewState and HTML control values (heavy traffic) Full Page lifecycle (heavy server processing) Controls outside the UpdatePanel do Render(NullTextWriter) Must use ScriptManager If no client-side JavaScript, it can fall back to regular PostBack with no JavaScript (?) No flicker/scroll since it's an async call, unless it falls back to regular postback. Can be used with master pages and user controls Has built-in support for progress bar Returns HTML for controls inside UpdatePanel (medium traffic) Client CallBack (Page, System.Web.UI.ICallbackEventHandler) Inherits Page Most of Page lifecycle (heavy server processing) Takes only data you specify (light traffic) and optionally ViewState (?) (medium traffic) Client must support JavaScript and use ScriptManager No flicker/scroll since it's an async call Can be used with master pages and user controls Returns only data you specify in format you specify (e.g. JSON, XML...) (?) (light traffic) WebMethod Class implements System.Web.Service.WebService HttpContext available through this.Context Takes only data you specify (light traffic) Server only runs the called method (light server processing) Client must support JavaScript No flicker/scroll since it's an async call Can be used with master pages and user controls Returns only data you specify, typically JSON (light traffic) Can create instance of server control to render HTML and sent back as string, but events, paging in GridView, etc. won't work PageMethods Essentially a WebMethod contained in the Page class, so most of WebMethod's bullet's apply Method must be public static, therefore no Page instance accessible HttpContext available through HttpContext.Current Accessed directly by URL Page.aspx/MethodName (e.g. with XMLHttpRequest directly or with library such as jQuery) Setting ScriptManager property EnablePageMethods="True" generates a JavaScript proxy for each WebMethod Cannot be used directly in user controls with master pages and user controls Any others?

  Read the article

• $_GET encoding problem with cyrillic text

  - by T1000

  I'm trying this code (on my local web server) <?php echo 'the word is / ?????? ? '.$_GET['word']; ?> but I get corrupted result when enter ?word=????? the word is / ?????? ? ???? The document is saved as 'UTF-8 without BOM' and headers are also UTF-8. I have tried urlencode() and urldecode() but the effect was same. When upload it on web server, works fine...

  Read the article

• Website for prototyping OO class diagrams

  - by JavaRocky

  Do any web 2.0 like websites exist for prototyping object oriented class diagrams?

  Read the article

• Convert BLOB to Jpg using C#

  - by TGuimond

  Hello, I am currently developing a web application that receives data from an on-site oracle database. The database developers have developed some web-services that I am able to call and send/receive data to and from the the database. When I want to display an image the method returns the image in BLOB format. My question is: what is the best way to convert BLOB to .jpg or .bmp so I can display the image correctly? If someone could point me in the right direction that would be great! Cheers, Tristan

  Read the article

• Common MVC 2 Pitfalls

  - by mcass20

  I surprised this hasn't been asked before...or maybe I just don't see it. Anyway, I'm finally straying from the comfort of ASP.NET Web Forms and exploring the world of MVC2. I've done the nerdinner walk-through and it was fairly straightforward. Now I am getting a little more adventurous and building an MVC2 app on my own and would like to know if there are some common pitfalls that others can attest to. Please consider my background as an ASP.NET Web Forms developer. Thanks!

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• iPhone Options for reading item from XML?

  - by fuzzygoat

  I am accessing this data from a web server using NSURL, what I am trying to decide is should I read this as XML or should I just use NSScanner and rip out the [data] bit I need. I have looked around the web for examples of extracting fields from XML on the iPhone but it all seems a bit overkill for what I need. Can anyone make any suggestions or point me in the right direction. In an ideal world I would really like to just specify [data] and get a string back "2046 3433 5674 3422 4456 8990 1200 5284" <!DOCTYPE tubinerotationdata> <turbine version="1.0"> <status version="1.0" result="200">OK</status> <data version="1.0"> 2046 3433 5674 3422 4456 8990 1200 5284 </data> </turbine> any comments / ideas are much appreciated. gary

  Read the article

• Forcing a page to load itself in another page's iframe

  - by bufferz

  I'm a fairly inexperienced web designer learning css/html on the fly for a company's web site. I want to keep menus, banners, etc in one document so I don't have to repeat updates across many documents. My solution was to make an index.aspx file with the menus and headers, then have a simple iframe for content. This works quite well and updates easily. the format is: www.site.com/index.aspx?page=page1.htm www.site.com/index.aspx?page=page2.htm The problem -- Google is indexing my iframe'd pages and linking to them directly: www.site.com/page1.htm www.site.com/page2.htm How can I set up redirects to page1.htm forwards to index.aspx?page=page1.htm without creating a "hall of mirrors" effect inside the original iframe?

  Read the article

• Extend LDAP Membership to append a prefix/sufix to the username

  - by Romias

  Our web applications are using LDAP Membership Provider to authenticate and register users in Active Directory. In order to allow users to provide usernames that exist in other applications, we need to add a prefix in its username and it should be as transparent and painless as possible. What I need is a way to extend the LDAP Membership Provider to be able to add (concatenate) a prefix to the username just before Membership authenticate or register it. For example, if user input is "JohnS" in application 1... I want to authenticate: "App1_JohnS". How could I extend the membership to accomplish this? Any idea what is triggered just before authenticate and register (create user)? Update: Each web app has an "OU" in AD where create users to and authenticate from. But as it is just ONE Active Directory Controller the usernames must be unique. We need to solve this issue using Membership providers and not adding more ADs.

  Read the article

• What does a modern, standard Microsoft-based technology stack look like?

  - by Sean Owen

  Let's say I asked Microsoft to describe the perfect, modern, Microsoft-based technology stack to power a standard e-commerce web site, which perhaps has a simple 2-tier web/database architecture. What would it be like? Yes, I'm just looking for a list of product / technology names. For example, in the J2EE world, I might describe a stack that includes: J2EE 6 standard JavaServer Faces Glassfish 3 MySQL 5.1.x I'm guessing this stack includes some combination of .NET, SQL Server, ASP.NET, IIS, etc. but I am not familiar with this world. Looking for ideas on the equivalent in Microsoft-land.

  Read the article

• rsync creating thousands of ..ds_store files from mounted volume

  - by daniel Crabbe

  hello there - been using rsync on os x to sync all our website admins. it was working fine until the os x 10.6.3 update! Now it creates thousands of ZeroK folders. It only does it when synching to a mounted drive(which we need to do) as when i sync to my hd it works as usual! i've tried excludes which don't seem to be working... also tried different version of rsync so its an os x issue. echo "" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" echo " SYNCING up KINEMASTIK" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" /usr/local/bin/rsync -aNHAXv --progress --exclude-from 'exclude.txt' /Volumes/Groups/Projects/483_Modern_Activity_Website/web/youradmin/ /Users/dan/Dropbox/documents/WORK/kinemastik/WEBSITE/youradmin/ echo "" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" echo " SYNCING up CHRIS BROOKS YOURADMIN" echo "~*~*~*~*~*~*~*~*~*~*~*~*~*" /usr/local/bin/rsync -aNHAXv --progress --exclude-from 'exclude.txt' /Volumes/Groups/Projects/483_Modern_Activity_Website/web/youradmin/ /Volumes/Groups/Projects/516_ChrisBrooks/website/youradmin/ anyone experienced the same? many thnks, D.

  Read the article

• Can unexpected power loss harm a Linux install?

  - by Johan Elmander

  I am developing an application on a Linux embedded board (runs Debian) e.g. Raspberry Pi, Beagle Board/Bone, or olimex. The boards works on an environment that the electricity is cut unexpectedly (it is far complicated to place PSU, etc.) and it would happen every day couple times. I wonder if the unexpected power cuts would cause crash/problem on the Linux Operation System? If it is something that I should worry, what would you suggest to prevent the damages on OS against the unexpected power cuts? PS. The application needs to writes some data to the storage medium (SD card), I think it would not be suitable to mount it as read-only.

  Read the article

• Allow image upload - most efficient way?

  - by K-P

  Hey everyone, In my site, I currently only allow users to import images from other sites rather than uploading it themselves. The main reason for this is because I don't have much storage space on my host (relatively speaking). The host charges quite a bit for additional space. What are the alternatives to hosting images users upload (max 1mb size). Would it be a good idea to purchase separate cheap hosting with "unlimited space" (I know that's not true, but I'm guessing it's more than 1gb)? Or are there some caveats with this approach (e.g. security since the site should not be browsable, but accessed via another server)? Are there alternative ideas that I could employ? Thanks for any suggestions

  Read the article

• PHP Tag Cloud System

  - by deniz

  Hi, I am implementing a tag cloud system based on this recommendation. (However, I am not using foreign keys) I am allowing up to 25 tags. My question is, how can I handle editing on the items? I have this item adding/editing page: Title: Description: Tags: (example data) computer, book, web, design If someone edits an item details, do I need to delete all the tags from Item2Tag table first, then add the new elements? For instance, someone changed the data to this: Tags: (example data) computer, book, web, newspaper Do I need to delete all the tags from Item2Tag table, and then add these elements? It seems inefficient, but I could find a more efficient way. The other problem is with this way is, if someone edits description but does not change the tags box, I still need to delete all the elements from Item2Tag table and add the same element. I am not an experienced PHP coder, so could you suggest a better way to handle this? (pure PHP/MySQL solution is preferable) Thanks in advance,

  Read the article

• org.apache.jasper.JasperException: The absolute uri: http://java.sun.com/jsp/jstl/core cannot be res

  - by user291750

  I've been having the following problem with my GoDaddy's server. I am using JSPs with the JSTL Library. My /WEB-INF/lib folder contains the following libraries: jstl.jar standard.jar My JSP looks something like this: <%@ taglib prefix="c" uri="http://java.sun.com/jsp/jstl/core" %> <p>Hello! <% out.print(System.getProperty("java.class.path")); %></p> But I keep getting the following exception: org.apache.jasper.JasperException: The absolute uri: http://java.sun.com/jsp/jstl/core cannot be resolved in either web.xml or the jar files deployed with this application Any ideas as to why it is doing that? Thanks

  Read the article

• How do the routers communicate with each other ?

  - by Berkay

  Let's say that i want make a request a to a web page which is hosted in Europe (i live in USA).My packets only consist the IP address of the web page, first the domain name to ip address transformation is done, then my packets start their journey through to europe. i assume that MAC addresses never used in this situation? are they? First, my packets deal with many routers on way how these routers communicate with each other?, are router addresses added to my packet headers ? Second, is there a specific path router to router comminication or which conditions affect this route? Third to cross the Atlantic Ocean, are cables used or... ?

  Read the article

• Capistrano configuration

  - by Eli

  I'm having some issues with variable scope with the capistrano-ext gem's multistage module. I currently have, in config/deploy/staging.rb. set(:settings) { YAML.load_file("config/deploy.yml")['staging'] } set :repository, settings["repository"] set :deploy_to, settings["deploy_to"] set :branch, settings["branch"] set :domain, settings["domain"] set :user, settings["user"] role :app, domain role :web, domain role :db, domain, :primary => true My config/deploy/production.rb file is similar. This doesn't seem very DRY. Ideally, I think I'd like everything to be in the deploy.rb file. If there were a variable set with the current stage, everything would be really clean. UPDATE: I found a solution. I defined this function in deploy.rb: def set_settings(params) params.each_pair do |k,v| set k.to_sym, v end if exists? :domain role :app, domain role :web, domain role :db, domain, :primary => true end end Then my staging.rb file is just set_settings(YAML.load_file("config/deploy.yml")['staging'])

  Read the article

• Developer tool for configuring IIS6

  - by Marc Gravell

  edit: IIS6; I'm not sure IIS7 is an option in the immediate future... From a developer angle, I am constantly changing my IIS settings, or need to merge settings from other teams into different VMs. The "Save Configuration to Disk" has never really worked well for me. Because we are making lots of small changes, web installation projects have never really worked either... Tools aimed for the web-admin aren't necessarily a good fit for the developer - we have different aims and needs. Does anyone have a script / tool / utility that would allow us to quickly configure IIS? In particular: remove everything (start clean) add a load of virtual directories, each mapped to application base paths set as an application set the app-pool (we'll assume the app pool already exists) set the ASP.NET version to 2.x if needed from some find of flat input list (any format would do).

  Read the article

• Copy Structure To Another Program

  - by Steven

  Long story, long: I am adding a web interface (ASPX.NET: VB) to a data acquisition system developed with LabVIEW which outputs raw data files. These raw data files are the binary representation of a LabVIEW cluster (essentially a structure). LabVIEW provides functions to instantiate a class or structure or call a method defined in a .NET DLL file. I plan to create a DLL file containing a structure definition and a class with methods to transfer the structure. When the webpage requests data, it would call a LabVIEW executable with a filename parameter. The LabVIEW code would instantiate the structure, populate the structure from the data file, then call the method to transfer the data back to the website. Long story, short: How do you recommend I transfer (copy) an instance of a structure from one .NET program to a VB.NET program? Ideas considered: sockets, temp file, xml file, config file, web services, CSV, some type of serialization, shared memory

  Read the article

< Previous Page | 917 918 919 920 921 922 923 924 925 926 927 928  | Next Page >