Search Results

Search found 47251 results on 1891 pages for 'web storage'.

Page 924/1891 | < Previous Page | 920 921 922 923 924 925 926 927 928 929 930 931  | Next Page >

• Motherboard/PSU crippling USB and Sata

  - by celebdor

  I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

  Read the article

• Explain the Peak and Flag Algorithm

  - by Isaac Levin

  EDIT Just was pointed that the requirements state peaks cannot be ends of Arrays. So I ran across this site http://codility.com/ Which gives you programming problems and gives you certificates if you can solve them in 2 hours. The very first question is one I have seen before, typically called the Peaks and Flags question. If you are not familiar A non-empty zero-indexed array A consisting of N integers is given. A peak is an array element which is larger than its neighbours. More precisely, it is an index P such that 0 < P < N - 1 and A[P - 1] < A[P] A[P + 1] . For example, the following array A: A[0] = 1 A[1] = 5 A[2] = 3 A[3] = 4 A[4] = 3 A[5] = 4 A[6] = 1 A[7] = 2 A[8] = 3 A[9] = 4 A[10] = 6 A[11] = 2 has exactly four peaks: elements 1, 3, 5 and 10. You are going on a trip to a range of mountains whose relative heights are represented by array A. You have to choose how many flags you should take with you. The goal is to set the maximum number of flags on the peaks, according to certain rules. Flags can only be set on peaks. What's more, if you take K flags, then the distance between any two flags should be greater than or equal to K. The distance between indices P and Q is the absolute value |P - Q|. For example, given the mountain range represented by array A, above, with N = 12, if you take: two flags, you can set them on peaks 1 and 5; three flags, you can set them on peaks 1, 5 and 10; four flags, you can set only three flags, on peaks 1, 5 and 10. You can therefore set a maximum of three flags in this case. Write a function that, given a non-empty zero-indexed array A of N integers, returns the maximum number of flags that can be set on the peaks of the array. For example, given the array above the function should return 3, as explained above. Assume that: N is an integer within the range [1..100,000]; each element of array A is an integer within the range [0..1,000,000,000]. Complexity: expected worst-case time complexity is O(N); expected worst-case space complexity is O(N), beyond input storage (not counting the storage required for input arguments). Elements of input arrays can be modified. So this makes sense, but I failed it using this code public int GetFlags(int[] A) { List<int> peakList = new List<int>(); for (int i = 0; i <= A.Length - 1; i++) { if ((A[i] > A[i + 1] && A[i] > A[i - 1])) { peakList.Add(i); } } List<int> flagList = new List<int>(); int distance = peakList.Count; flagList.Add(peakList[0]); for (int i = 1, j = 0, max = peakList.Count; i < max; i++) { if (Math.Abs(Convert.ToDecimal(peakList[j]) - Convert.ToDecimal(peakList[i])) >= distance) { flagList.Add(peakList[i]); j = i; } } return flagList.Count; } EDIT int[] A = new int[] { 7, 10, 4, 5, 7, 4, 6, 1, 4, 3, 3, 7 }; The correct answer is 3, but my application says 2 This I do not get, since there are 4 peaks (indices 1,4,6,8) and from that, you should be able to place a flag at 2 of the peaks (1 and 6) Am I missing something here? Obviously my assumption is that the beginning or end of an Array can be a peak, is this not the case? If this needs to go in Stack Exchange Programmers, I will move it, but thought dialog here would be helpful. EDIT

  Read the article

• open source reputation system framework

  - by cometta

  any web reputation framework to recommend for java developer?

  Read the article

• Most efficient way to extract bit flags

  - by Hallik

  I have these possible bit flags. 1, 2, 4, 8, 16, 64, 128, 256, 512, 2048, 4096, 16384, 32768, 65536 So each number is like a true/false statement on the server side. So if the first 3 items, and only the first 3 items are marked "true" on the server side, the web service will return a 7. Or if all 14 items above are true, I would still get a single number back from the web service which is is the sum of all those numbers. What is the best way to handle the number I get back to find out which items are marked as "true"?

  Read the article

• How do you disable SMB printing support?

  - by evilpenguin

  Hi, I'm running CentOS on a storage server that has to do file sharing for with Windows machines. SMB version is smbd version 3.5.5-68.fc13 I'm getting a lot of error messages in /var/log/messages regarding failed attempts to connect to a CUPS server. They look like this: Nov 30 18:49:34 big03 smbd[9927]: [2010/11/30 18:49:34.850620, 0] printing/print_cups.c:108(cups_connect) Nov 30 18:49:34 big03 smbd[9927]: Unable to connect to CUPS server localhost:631 - Connection refused I understand that the issue is generated by the fact that SMB comes with printer sharing support, but I'm really not interested in that. I just want to disable the feature to get rid of the messages. Any idea how I can do that?

  Read the article

• How to build Lucene / Solr from source code in windows environment in order to add patches

  - by Simon

  I have successfully implemented Apache’s Solr for free text searching a database driven web site build for windows platforms using Visual Studio in c#. I am trying to get a version Solr working with field collapsing (which is not in the release version). There are patches available from apache and discussions on the web of people successfully doing this for the version I am using but my problem is cannot get the build to work. I am a c# coder on windows platforms so java development is new to me. I understand I need to get the correct source code (and revision) from SVN, add the appropriate patches, then build the war file to deploy to my system. I cannot seem to get the source to build and produce the deployment code including jar (and subsequent war) files. My system is: Windows 7 Ultimate for development Visual Studio 2010 for c# / javascript development MyEclipse 8.6 / Eclipse 3.5 for the java build from source Subecplise 1.6x SVN plugin to get the source from apache’s SVN Apache Solr 1.4.1 So far I have: Found the right patches for the function I need: https://issues.apache.org/jira/browse/SOLR-236 Specifically I need to patch: field_collapsing_1.1.0.patch HTTPS //issues.apache.org/jira/secure/attachment/12357681/field_collapsing_1.1.0.patch and SOLR-236-1_4_1.patch HTTPS //issues.apache.org/jira/secure/attachment/12448216/SOLR-236-1_4_1.patch I downloaded the Lucene trunk version from the day before the patch was released (revision 958303 from 28/6/10) via subeclipse into a java package in myeclipse from: HTTPS //svn.apache.org/repos/asf/lucene/dev/trunk (Solr is the web implementation of Lucene and is in the subfolder solr/) I can apply patches to the solr directory once it has downloaded but the parent Lucene project doesn’t build the war files, copy the jar or other files into the bin folder (it stays empty). The build process starts, but doesn’t do anything apart from creating the folders bin and src. I am building the whole Lucene project, which contains Solr. I have tried building the source without patching and the same happens. If I copy out the Solr directory into a new project, it runs the build and copies all the related files, tests, etc but fails with 4,500 errors and does not produce the jar files or war file, which I assume is because it can’t find the Lucene trunk files which it depends on. I have two interrelated problems 1) I can't get the Lucene downloaded trunk to build 2) The jar, war and associated files are not created Can anyone help with what I am missing to build the war file? I have spent 2 days to get this far as the help online is extremely patchy and I can’t find a walk though tutorial on building a java war file from source in a windows environment. Any help will be much appreciated. Simon

  Read the article

• Flex Inheriting Logged in User

  - by Nick

  I am trying to secure my Flex application within my Java web application. Currently my Java web application, handles logging and managing user accounts and the like. I was wondering if there is a way to essentially share that user credentials with the Flash movie in a secure mechanism? For instance, if you log in, we want you to be able to save items in the Flex application for that user, only if that user is logged in of course. Any ideas? Any help is greatly appreciated.

  Read the article

• custom tag 'cannot be resolved to a type'

  - by lotus99t

  I have a custom tag, packaged into a library jar that is included in my web apps war file. I get the following error: An error occurred at line: 66 in the jsp file: /WEB-INF/jsp/portlet/portfolio/operations/operationsInfo.jsp org.apache.jsp.tag.meta.form.WidgetFactory_tag cannot be resolved to a type 63: <c:forEach var="fldCfg" items="${config.page.fields}" > 64: <tr> 65: <td><form:Label fld="${fldCfg}"/></td> 66: <td><form:WidgetFactory fld="${fldCfg}" decodesMap="${decodesMap}" command="${operationsInfoBean}" dateFormat="${preferredDateFormat}"/></td> 67: </tr> 68: </c:forEach> 69: </table> But it doesn't seem to complain about Label which is in the same taglib. I've confirmed that the jar is in the war and that the tag file is in the jar and the that the TLD (in META-INF) expressly defines 'WidgetFactory' Why am I getting this error?

  Read the article

• Why Banks or Financial Companies prefer Oracle than other RDBMS for their "Core" systems?

  - by edwin.nathaniel

  I'd like to know why most Banks or Financial companies prefer Oracle than other RDBMS for their core systems (the absolutely minimum features that a Bank must support). I found a few answers that didn't satisfy me. For example: Oracle has more features. But features for what? Can't you implement that in application level if you were not using Oracle? Could someone please describe a bit more technical but still on high-level overview of what the bank needs and how Oracle would solve it and the others can't or don't have the features yet? I came from the web-app (web 2.0) crowd who normally hear news about MySQL, PostgreSQL or even key-value/column-oriented storage solution. I have almost zero knowledge on how Banks or Financial companies operates from technical perspective. Thank you, Ed

  Read the article

• What to filter when providing very limited open WiFi to a small conference or meeting?

  - by Tim Farley

  Executive Summary The basic question is: if you have a very limited bandwidth WiFi to provide Internet for a small meeting of only a day or two, how do you set the filters on the router to avoid one or two users monopolizing all the available bandwidth? For folks who don't have the time to read the details below, I am NOT looking for any of these answers: Secure the router and only let a few trusted people use it Tell everyone to turn off unused services & generally police themselves Monitor the traffic with a sniffer and add filters as needed I am aware of all of that. None are appropriate for reasons that will become clear. ALSO NOTE: There is already a question concerning providing adequate WiFi at large (500 attendees) conferences here. This question concerns SMALL meetings of less than 200 people, typically with less than half that using the WiFi. Something that can be handled with a single home or small office router. Background I've used a 3G/4G router device to provide WiFi to small meetings in the past with some success. By small I mean single-room conferences or meetings on the order of a barcamp or Skepticamp or user group meeting. These meetings sometimes have technical attendees there, but not exclusively. Usually less than half to a third of the attendees will actually use the WiFi. Maximum meeting size I'm talking about is 100 to 200 people. I typically use a Cradlepoint MBR-1000 but many other devices exist, especially all-in-one units supplied by 3G and/or 4G vendors like Verizon, Sprint and Clear. These devices take a 3G or 4G internet connection and fan it out to multiple users using WiFi. One key aspect of providing net access this way is the limited bandwidth available over 3G/4G. Even with something like the Cradlepoint which can load-balance multiple radios, you are only going to achieve a few megabits of download speed and maybe a megabit or so of upload speed. That's a best case scenario. Often it is considerably slower. The goal in most of these meeting situations is to allow folks access to services like email, web, social media, chat services and so on. This is so they can live-blog or live-tweet the proceedings, or simply chat online or otherwise stay in touch (with both attendees and non-attendees) while the meeting proceeds. I would like to limit the services provided by the router to just those services that meet those needs. Problems In particular I have noticed a couple of scenarios where particular users end up abusing most of the bandwidth on the router, to the detriment of everyone. These boil into two areas: Intentional use. Folks looking at YouTube videos, downloading podcasts to their iPod, and otherwise using the bandwidth for things that really aren't appropriate in a meeting room where you should be paying attention to the speaker and/or interacting.At one meeting that we were live-streaming (over a separate, dedicated connection) via UStream, I noticed several folks in the room that had the UStream page up so they could interact with the meeting chat - apparently oblivious that they were wasting bandwidth streaming back video of something that was taking place right in front of them. Unintentional use. There are a variety of software utilities that will make extensive use of bandwidth in the background, that folks often have installed on their laptops and smartphones, perhaps without realizing.Examples: Peer to peer downloading programs such as Bittorrent that run in the background Automatic software update services. These are legion, as every major software vendor has their own, so one can easily have Microsoft, Apple, Mozilla, Adobe, Google and others all trying to download updates in the background. Security software that downloads new signatures such as anti-virus, anti-malware, etc. Backup software and other software that "syncs" in the background to cloud services. For some numbers on how much network bandwidth gets sucked up by these non-web, non-email type services, check out this recent Wired article. Apparently web, email and chat all together are less than one quarter of the Internet traffic now. If the numbers in that article are correct, by filtering out all the other stuff I should be able to increase the usefulness of the WiFi four-fold. Now, in some situations I've been able to control access using security on the router to limit it to a very small group of people (typically the organizers of the meeting). But that's not always appropriate. At an upcoming meeting I would like to run the WiFi without security and let anyone use it, because it happens at the meeting location the 4G coverage in my town is particularly excellent. In a recent test I got 10 Megabits down at the meeting site. The "tell people to police themselves" solution mentioned at top is not appropriate because of (a) a largely non-technical audience and (b) the unintentional nature of much of the usage as described above. The "run a sniffer and filter as needed" solution is not useful because these meetings typically only last a couple of days, often only one day, and have a very small volunteer staff. I don't have a person to dedicate to network monitoring, and by the time we got the rules tweaked completely the meeting will be over. What I've Got First thing, I figured I would use OpenDNS's domain filtering rules to filter out whole classes of sites. A number of video and peer-to-peer sites can be wiped out using this. (Yes, I am aware that filtering via DNS technically leaves the services accessible - remember, these are largely non-technical users attending a 2 day meeting. It's enough). I figured I would start with these selections in OpenDNS's UI: I figure I will probably also block DNS (port 53) to anything other than the router itself, so that folks can't bypass my DNS configuration. A savvy user could get around this, because I'm not going to put a lot of elaborate filters on the firewall, but I don't care too much. Because these meetings don't last very long, its probably not going to be worth the trouble. This should cover the bulk of the non-web traffic, i.e. peer-to-peer and video if that Wired article is correct. Please advise if you think there are severe limitations to the OpenDNS approach. What I Need Note that OpenDNS focuses on things that are "objectionable" in some context or another. Video, music, radio and peer-to-peer all get covered. I still need to cover a number of perfectly reasonable things that we just want to block because they aren't needed in a meeting. Most of these are utilities that upload or download legit things in the background. Specifically, I'd like to know port numbers or DNS names to filter in order to effectively disable the following services: Microsoft automatic updates Apple automatic updates Adobe automatic updates Google automatic updates Other major software update services Major virus/malware/security signature updates Major background backup services Other services that run in the background and can eat lots of bandwidth I also would like any other suggestions you might have that would be applicable. Sorry to be so verbose, but I find it helps to be very, very clear on questions of this nature, and I already have half a solution with the OpenDNS thing.

  Read the article

• Custom Types in WCF Rest

  - by user316341

  I am using the Rest Singleton WCF Service temple from the Rest Starter Kit. The temples uses sample item as its sample Item. i am attempting to replace that sample ITem with a custom type from web reference in my ASP.Net project .dll. The types and name spaces are found and i can replace the sample item in the code. when i run the application i get this error: "Exception has been thrown by the target of an invocation." when this line is executed "return new SingletonServiceHost(serviceType, baseAddresses);" <%@ ServiceHost Language="C#" Debug="true" Service="SAUDServices.Service" Factory="SAUDServices.AppServiceHostFactory"%> using System; using System.ServiceModel; using System.ServiceModel.Activation; using Microsoft.ServiceModel.Web.SpecializedServices; using Stretchatyourdesk; namespace SAUDServices { class AppServiceHostFactory : ServiceHostFactory { protected override ServiceHost CreateServiceHost(Type serviceType, Uri[] baseAddresses) { return new SingletonServiceHost(serviceType, baseAddresses); } } }

  Read the article

• uploading multiple files from client to server with asp.net

  - by Maestro1024

  uploading multiple files from client to server with asp.net I have been looking at the asp.net upload control but that is for one file (unless someone knows a better way to do it). http://msdn.microsoft.com/en-us/library/system.web.ui.webcontrols.fileupload.aspx For what I want to do I don't even really need a browse. I know the files off of the client are at a certain location. Is it possible to create a collection of *HttpPostedFile*s and upload those? http://msdn.microsoft.com/en-us/library/system.web.httppostedfile.aspx I don't think it is possible but would be glad to be proven wrong. Is there a different asp.net method or control that will easily allow uploading multiple files from client to server?

  Read the article

• Strategy for Offline/Online data synchronization

  - by Adi

  My requirement is I have server J2EE web application and client J2EE web application. Sometimes client can go offline. When client comes online he should be able to synchronize changes to and fro. Also I should be able to control which rows/tables need to be synchronized based on some filters/rules. Is there any existing Java frameworks for doing it? If I need to implement on my own, what are the different strategies that you can suggest? One solution in my mind is maintaining sql logs and executing same statements at other side during synchronization. Do you see any problems with this strategy?

  Read the article

• How to create Raid 10 with megacli

  - by Henno

  I have OpenFiler storage server. Without installing Windows and MSM, I want to create raid10 array from disks 2 to 21. I have already successfully installed MegaCli to OpenFiler but I'm stuck in figuring out the correct command line for creating a raid 10 array. The documentations says that the syntax for creating a raid 10 is: MegaCli -CfgSpanAdd -r10 -Array0[E:S,E:S] -Array1[E:S,E:S] -aN My enclosure ID is 25, so: [root@linux-h5ut ~]# MegaCli -CfgSpanAdd -r10 -Array0[E25:S02,E25:S21] -Array1[E25:S02,E25:S21] WB Cached NoCachedBadBBU -a0 Invalid input at or near token E I have googled high and low but there doesn't seem to be any example doing raid10 with megaraid (only the syntax). Can anyone explain what is wrong?

  Read the article

• what might cause a print error in perl?

  - by Mark J Seger

  I have a long running script that every hour opens a file, prints to it and closes the file. I've recently found very rarely, the print is failing, not because I'm testing the status of the print itself but rather due to the fact of missing entries in the file until the system is actually rebooted! I do trap for file open failures and write a message to syslog when that happens and I'm not seeing any open failures so I'm now guessing it may be the print that is failing. I'm not trapping the print failures, which I suspect most people don't but am now going to update that one print. Meanwhile, my question is does anyone know what types of situations could cause a print statement to fail when there is plenty of disk storage and no contention for a file which has been successfully opened in append mode?

  Read the article

• How to impelement messaging services in a website?

  - by Alex

  There's a website which currently has only web interfaces for all the users. However, new requirement has emerged which says that there is a need in providing an alternative interface for a certain group of website users who want to regularly receive pushed notifications(messages) that would inform them about new events(news) in their field of interest. What sort of interface would it be?Is it all about using a MOM(message-oriented middleware) like JMS and deploying it withing an application server on a website using publish/subscribe model?Is it the correct way how to meet these sort of requirements?And if it's not a web-based interface,would kind of interface would it be then for the users? Thanks

  Read the article

• Implementing website messaging services

  - by Alex

  There's a website which currently has only web interfaces for all the users. However, new requirement has emerged which says that there is a need in providing an alternative interface for a certain group of website users who want to regularly receive pushed notifications(messages) that would inform them about new events(news) in their field of interest. What sort of interface would it be?Is it all about using a MOM(message-oriented middleware) like JMS and deploying it withing an application server on a website using publish/subscribe model?Is it the correct way how to meet these sort of requirements?And if it's not a web-based interface,would kind of interface would it be then for the users? Thanks

  Read the article

• mysql and .net: when using tableadapters I'm getting MySqlException "insert command denied for user"

  - by Deveti Putnik

  Hi! I am using mysql as db for my asp.net application. Here are the facts: I am using connection string from web.config which has both username and password. I can do SELECT with tableadapter. When I am trying to do INSERT with tableadapter, I am getting "mysqlexception insert command denied for user" error When I try to do INSERT programatically, i.e. using connection, command object, etc. everything is fine. In this case, I'm reading connection string from web.config, too. This can be only applied to GoDaddy hosting, but on local machine I don't have this kind of problems. Can anyone suggest what can I do to make it work on GoDaddy hosting? Regards, D

  Read the article

• Any ideas for automatic initial/scripted configuration of a NetApp?

  - by maddenca

  The background is to make a solution where we can automate as much as possible the building up of ‘pods’ that include server/network/storage and that will be built at remote sites. In an ideal world would be that we create a single management server which is preconfigured with DHCP/TFTP/or whatever. This management server is racked with a CISCO UCS, FAS31x0, etc. at a build site and is then transported to the final customer site where on power it almost configures itself, or at least bootstraps itself far enough that a remote skilled 'expert' can complete the setup of the pod. Ideas (doesn't have to resemble 100% of the above) would be helpful.

  Read the article

• Chart Control Inside SSRS ReportViewer is Viewable From Localhost But Not Internet

  - by Daniel Coffman

  A project I own was just moved from an older server to a new one, and in the process of moving the web folder, re-deploying the SSRS reports, restoring the database, configuring IIS, etc... I have lost the ability to view the Microsoft Chart Controls that are embedded in the SSRS reports, that are then displayed by a Microsoft.ReportViewer. I could view them both locally and remotely (via the internet) on the old server. I can view them if I preview the SSRS report in Visual Studio. The report displays fine, only missing all the embedded charts. I can still view them locally through the web browser, just not from the internet. What am I missing? I tried giving permissions to the ChartImageHandler temp storage folder, but it didn't work. I'm getting the Javascript error: Error: ClientReport380ec8ca0c294a809e9986c1bef9db1c is undefined

  Read the article

• TrueCrypt & upgrading your hard drive?

  - by Danielb

  I currently use TrueCrypt to encrypt the hard drive in a Win7 laptop (everything in a single partition). I am looking to upgrade the hard drive to a model with significantly more storage capacity. I've had a look through the documentation but I couldn't see anything about this particular scenario. I assume I need to do something like the following: Remove the encryption from the existing drive. Clone the existing drive image onto the new hard drive. Physically install the new drive into the laptop. Resize the single partition to use all the space in the new drive. Encrypt all of the new bigger drive with TrueCrypt.

  Read the article

• How to create a SOAP REQUEST using ASP.NET (VB) without using Visual

  - by user311691

  Hi all , I urgently need your help . I am new to consuming a web service using SOAP protocol. I have been given a demo webservice URL which ends in .WSDL and NOT .asml?WSDL. The problem is I cannot add a web reference using Visual studio OR Disco.exe or Wsdl.exe - This webservice has been created on a java platform and for security reasons the only way to make a invoke the webservice is at runtime using SOAP protocol IN asp.net (VB). I I have created some code but cannot seem to send the soap object to the receiving web service. If I could get a solution with step by step instructions on how I can send a SOAP REQUEST. Below is my code and all am trying to do is send a SOAP REQUEST and receive a SOAP RESPONSE which I will display in my browser. <%@ page language="vb" %> <%@ Import Namespace="System.Data"%> <%@ Import Namespace="System.Xml"%> <%@ Import Namespace="System.Net"%> <%@ Import Namespace="System.IO"%> <%@ Import Namespace="System.Text"%> <script runat=server> Private Sub Page_Load() Dim objHTTPReq As HttpWebRequest Dim WebserviceUrl As String = "http://xx.xx.xx:8084/asy/wsdl/asy.wsdl" objHTTPReq = CType(WebRequest.Create(WebserviceUrl), HttpWebRequest) Dim soapXML As String soapXML = "<?xml version='1.0' encoding='utf-8'?>" & _ " <soap:Envelope xmlns:xsi='http://www.w3.org/2001/XMLSchema-instance'" & _ " xmlns:xsd='http://www.w3.org/2001/XMLSchema'"& _ " xmlns:soap='http://schemas.xmlsoap.org/soap/envelope/' >"& _ " <soap:Body> "& _ " <validatePaymentData xmlns='http://asybanks.webservices.asycuda.org'> " & _ " <bankCode>"& bankCode &"</bankCode> " & _ " <PaymentDataType>" & _ " <paymentType>"& payment_type &"</paymentType> " & _ " <amount>"& ass_amount &"</amount> " & _ " <ReferenceType>" & _ " <year>"& year &"</year> " & _ " <customsOfficeCode>"& station &"</customsOfficeCode> " & _ " </ReferenceType>" & _ " <accountNumber>"& zra_account &"</accountNumber> " & _ " </PaymentDataType> " & _ " </validatePaymentData> " & _ " </soap:Body> " & _ " </soap:Envelope> " objHTTPReq.Headers.Add("SOAPAction", "http://asybanks.webservices.asycuda.org") objHTTPReq.ContentType = "text/xml; charset=utf-8" objHTTPReq.ContentLength = soapXML.Length objHTTPReq.Accept = "text/xml" objHTTPReq.Method = "POST" Dim objHTTPRes As HttpWebResponse = CType(objHTTPReq.GetResponse(), HttpWebResponse) Dim dataStream As Stream = objHTTPRes.GetResponseStream() Dim reader As StreamReader = new StreamReader(dataStream) Dim responseFromServer As String = reader.ReadToEnd() OurXml.text = responseFromServer End Sub </script> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title> XML TRANSACTION SIMULATION - N@W@ TJ </title> </head> <body> <form id="form1" runat="server"> <div> <p>ZRA test Feedback:</p> <asp:label id="OurXml" runat="server"/> </div> </form> </body> </html> the demo webservice looks like this: <?xml version="1.0" encoding="UTF-8" ?> - <!-- WEB SERVICE JAVA DEMO --> - <definitions targetNamespace="http://asybanks.webservices.asycuda.org" xmlns="http://schemas.xmlsoap.org/wsdl/" xmlns:apachesoap="http://xml.apache.org/xml-soap" xmlns:soap="http://schemas.xmlsoap.org/wsdl/soap/" xmlns:xs="http://www.w3.org/2001/XMLSchema" xmlns:y="http://asybanks.webservices.asycuda.org"> - <types> - <xs:schema elementFormDefault="qualified" targetNamespace="http://asybanks.webservices.asycuda.org" xmlns="http://www.w3.org/2001/XMLSchema"> SOME OTHER INFORMATION AT THE BOTTOM <soap:address location="http://xx.xx.xx:8084/asy/services/asy" /> </port> </service> </definitions> From the above excerpt of the wsdl url webservice, I am not sure which namespace to use for soapACTION - please advise.... Please if you could comment every stage of a soap request and provide a working demo - I would be most grateful as I would be learning rather than just assuming stuff :)

  Read the article

• Security exception with ASP.NET AJAX toolkit

  - by Rod

  I've got an ASP.NET WebForms app that I've written, which uses the ASP.NET AJAX Toolkit. I've put the MultiView control onto the web form, and it worked fine, when I had it under Vista. Well, I had to replace my machine (HD failed) and I went to Windows 7 Ultimate. I tried copying the ASP.NET app from the system (before it finally failed for good) and put it onto the Windows 7 machine. I can bring up the app fine, go to all pages, but the one with these controls on it. When I do I get the following error: Security Exception Description: The application attempted to perform an operation not allowed by the security policy. To grant this application the required permission please contact your system administrator or change the application's trust level in the configuration file. Exception Details: System.Security.SecurityException: Request for the permission of type 'System.Web.AspNetHostingPermission, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089' failed. What's going on? How do I fix it?

  Read the article

• eclise java internal webbrowser progress listener?

  - by deepthinker121

  Hi All, I need to open an internal web browser from a custom eclipse wizard I have created - and so I am using IWebBrowser webBrowser = browser.createBrowser (IWorkbenchBrowserSupport.LOCATION_BAR | IWorkbenchBrowserSupport.AS_EDITOR | IWorkbenchBrowserSupport.NAVIGATION_BAR | IWorkbenchBrowserSupport.STATUS, null,"TestBrowser", "TestBrowser"); URL url = new URL("http://localhost:8080/app"); webBrowser.openURL(url); Now the problem is - the openURL needs time to complete as it tries to load a page for a webapp and as I am not able to get the progress of the 'load page' operation of the URL - my wizard progressmonitor completes before the URL can be completely loaded . Is there any way to get the status of the page load operation - (to check if its complete or it failed) or add a listener to indicate completion of page load? It is okay for me to use some other implementations of internal web browsers - so please suggest some other approach we cannot add a listener to IWebBrowser.. Thanks for ur help !!

  Read the article

• Updating a Data Source with a Dataset

  - by Paul

  Hi, I need advice. I have asp.net web service and winforms client app. Client call this web method and get dataset. 1. [WebMethod] 2. public DataSet GetSecureDataSet(string id) 3. { 4. 5. 6. SqlConnection conn = null; 7. SqlDataAdapter da = null; 8. DataSet ds; 9. try 10. { 11. 12. string sql = "SELECT * FROM Tab1"; 13. 14. string connStr = WebConfigurationManager.ConnectionStrings["Employees"].ConnectionString; 15. 16. conn = new SqlConnection(connStr); 17. conn.Open(); 18. 19. da = new SqlDataAdapter(sql, conn); 20. 21. ds = new DataSet(); 22. da.Fill(ds, "Tab1"); 23. 24. return ds; 25. } 26. catch (Exception ex) 27. { 28. throw ex; 29. } 30. finally 31. { 32. if (conn != null) 33. conn.Close(); 34. if (da != null) 35. da.Dispose(); 36. } 37. } After he finish work he call this update web method. He can add, delete and edit rows in table in dataset. [WebMethod] public bool SecureUpdateDataSet(DataSet ds) { SqlConnection conn = null; SqlDataAdapter da = null; SqlCommand cmd = null; try { DataTable delRows = ds.Tables[0].GetChanges(DataRowState.Deleted); DataTable addRows = ds.Tables[0].GetChanges(DataRowState.Added); DataTable editRows = ds.Tables[0].GetChanges(DataRowState.Modified); string sql = "UPDATE * FROM Tab1"; string connStr = WebConfigurationManager.ConnectionStrings["Employees"].ConnectionString; conn = new SqlConnection(connStr); conn.Open(); cmd = new SqlCommand(sql, conn); da = new SqlDataAdapter(sql, conn); if (addRows != null) { da.Update(addRows); } if (delRows != null) { da.Update(delRows); } if (editRows != null) { da.Update(editRows); } return true; } catch (Exception ex) { throw ex; } finally { if (conn != null) conn.Close(); if (da != null) da.Dispose(); } } Code on client side 1. //on client side is dataset bind to datagridview 2. Dataset ds = proxy.GetSecureDataSet(""); 3. ds.AcceptChanges(); 4. 5. //edit dataset 6. 7. 8. //get changes 9. DataSet editDataset = ds.GetChanges(); 10. 11. //call update webmethod 12. proxy.SecureUpdateDataSet(editDataSet) But it finish with this error : System.Web.Services.Protocols.SoapException: Server was unable to process request. --- System.InvalidOperationException: Update requires a valid UpdateCommand when passed DataRow collection with modified rows. at WebService.Service.SecureUpdateDataSet(DataSet ds) in D:\Diploma.Work\WebService\Service1.asmx.cs:line 489 Problem is with SQL Commad, client can add, delete and insert row, how can write a corect SQL command.... any advice please? Thank you

  Read the article

< Previous Page | 920 921 922 923 924 925 926 927 928 929 930 931  | Next Page >