Search Results

Search found 13434 results on 538 pages for 'boot on power up'.

Page 93/538 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

  • What Is The Proper Laptop Battery Care While Running Laptop Solely On Battery?

    - by Boris_yo
    Because of convenience, I had to move my laptop to another room away from room where I always ran laptop on UPS without using battery. Since so far I always run laptop on battery, I question the proper usage to prolong battery life. Currently I run laptop on battery with power supply so battery is constantly being charged until it is full 100% and when it is, I disconnect power supply and continue working until battery meter shows 10% remaining. That's when I plug in power supply and let it charge until 100% once again while I work. But it takes a lot of time to fully charge laptop while working since my power supply is 60W which should be the reason of such slow charge and I think the kind of charger that I use is express charger. The thought of charging laptop until full, all while doing my work makes me think that if it takes way more time to charge, it might keep battery running warm for the period of charging time which brings me to question about whether I should keep running laptop as I've described above or it would be better to leave power supply constantly connected to laptop to keep battery between 99%-100%? On one hand it won't keep battery warm but it will try to frequently supply charge to battery once it gets 99% to replenish charge to 100% (which might reduce battery life?). On the other hand if I'll keep working solely on battery and recharge it when below 10%, the battery will get warm but only when charged. Can anybody suggest the correct way of running laptop on battery to ensure better battery life? Dell Latitude E6420 Windows 7 64-bit

    Read the article

  • Chassis fans and power LEDs still work in Hibernate

    - by Jaded
    I have ASRock Z68 Extreme3 Gen3 motherboard recently updated to 2.20 BIOS version. OS is Windows 7 x64. The problem is after that update full hibernation (by that i mean full system power off) stopped working although everything was fine before. Now when I press hibernate, sleep in initiated as usual, monitor goes to sleep, HDD and CPU fan stop spinning, but chassis fans (i have Gigabyte Aurora 3D 570 case with two rear and one front fans) still remain working. Also power leds are lit as if computer is turned on. Tried changing different UEFI settings related to sleep mode, and none of them change above described behaviour. I have "Deep Sleep" (Advanced-South Bridge Configuration) set to "Enabled in S4-S5", "Suspend to RAM" (Advanced-ACPI Configuration) set to "Auto", all fans settings in "H/W Monitor" set to "Auto".

    Read the article

  • Why does my screen dim on a desktop installation of Windows 7?

    - by Robert Cartaino
    Periodically, while using my Windows 7 Pro desktop installation, the screen suddenly dims. The brightness is about 75% normal (estimate). It's as if I am in a power-saving mode on a laptop running on batteries. But this is a full desktop installation. I know it is not a hardware glitch or monitor adjustment issue because the Windows cursor is still bright white while everything else goes dim. The Control Panel Power Options have not been changed. They are set to "Balanced [active]" and I have tried restoring the default settings. Flipping through the power and display settings, everything looks "normal." There is no screen saver or power-off-after settings apparent. Rebooting the system resets everything to full brightness but I can't find a way to restore it in Windows or to keep it from happening in the first place. Suggestions?

    Read the article

  • Laptop not powering down when lid is closed, but when lid is opened

    - by BENBUN
    Currently when I close the lid of my Acer laptop running Windows Vista, the laptop does not power down; however, when I open the lid it does. When looking at the power settings it is set to power down when closing the lid. The trigger to this seems to be the lid being opened not being closed. I seem to recall this behaviour changing when I installed Windows Media centre. Any ideas on how I can get the power down to work on the lid closing? Thanks.

    Read the article

  • Freebsd Box hangs on boot loader

    - by user19039
    I have a freebsd box that seems to not want to boot past the boot loader. It wont go past the initial boot loader phase and just lists the version number for the boot loader(btx loader). It hangs there. I am not a fluent freebsd admin and decent at command line, however I can tell clearly it wont get past and boot past the disk. Loaded up rescue cd, mounted the drive. Couldnt get fsck going without seg faulting How do i get this fixed? I have a live cd.... just curious which route to take.

    Read the article

  • How much money can I save from installing a 80 plus bronze or gold PSU? [closed]

    - by David
    Currently I've only a 300 watt PSU and my pc is working like a charm but with all the components it should use the psu to the max. Recently I've read about 80 plus certificate and I'm wondering if it's worth to buy a 80 plus certificate psu? My power cost last year was also higher then before and my pc turns almost 14/7 a day. I mean power cost in used power not in augmented prices. I'm also planing to buy a SLI video card.

    Read the article

  • Laptop changes closing lid power options based on media/music playing

    - by Backdraft
    Hi, This is on a Lenovo X60 running Windows 7 Professional. This is just a pet peeve of mine, but I was wondering if it were somehow possible to have my laptop autodetect whether any media/music is playing on and change/switch the "Close lid" options under Power Options, ie. when something is playing change state to "Do Nothing" otherwise change state to "Sleep". I guess I can probably set a some key combo up with AutoHotKey to do it, but was hoping Windows could detect and switch my Power Options automatically. Thanks.

    Read the article

  • Dell Power Edge R515 - Replacing a Bad Hard Drive in a RAID

    - by LonnieBest
    I've ordered a new hard drive to replace a bad one in a Dell Power Edge R515. The manual covers obvious topics regarding physical replacing of hard drives, but I've never done this before on a production server where RAID is involved. I've heard people talk about this topic, and I've heard that some servers have RAID controllers that are smart enough to allow you to just put in the new drive (hot swap), and then the server will know automatically how to rebuild that drive to be what the old one was to the system. Where do I find the proper procedure for replacing a failed hard drive on a live production Dell Power Edge R515? Can someone with experience tell me how easy or hard this usually is?

    Read the article

  • Enabling the Power State Change Beep

    - by digitxp
    I have a Thinkpad T430s. I found on other Thinkpads there's a beep when you plug or unplug the AC cord. While I hear a lot of people say it's annoying it seems like a very useful security feature. However, when I go into the Power Manager the option to beep on plugging/unplugging ("Power State Change Beep") isn't there, even though it's in the help file already. I know it would be easy to rig a software solution to this event, but it would kind of defeat the purpose if it doesn't beep when it's in sleep. Is there a way to get this beep on my laptop?

    Read the article

  • ESXi standalone host cannot power on any virtual machines

    - by Mark Henderson
    I have a standalone VMWare ESXi host on ESXi 5.1. It currently has a handful of VMs powered on, and they are running fine. If I try to power on any other VM - any VM at all - I am receiving the following message: Power On virtual machine:A general system error occurred: The virtual machine could not start I have been through everything on KB2001005 and KB1006232 and their steps are either not applicable, or don't change anything. Nothing is generated in the virtual machine's log file. Where can I troubleshoot from here?

    Read the article

  • CPU clock scales down so computer is unusable after switching to battery

    - by Ryan
    When I am plugged in my laptop runs great however when I unplug it and I'm on battery power my CPU clock speed scales down pretty much all the way. I know this is happening by monitoring the clock speed. When plugged in it will usually stay between 1000MHz and 3000MHz but when I unplug it it quickly scales down to less than 500MHz and will get as low as 100MHz and it will NEVER scale up at all on battery power. After I plug the power back in it will then begin operating normally in about a minute. I have tried setting the MIN and MAX CPU performance in power options to 100% and have tried messing around with cooling settings which seemed to be a problem with HP laptops. I have a Toshiba Satellite M500-ST6444 running Windows 7. The BIOS is up to date. I have tried two versions.

    Read the article

  • How to boot window from recovery partition?

    - by Zack
    Acer service center created recovery discs for my acer laptop. And they also created a partition in which contains the data from recovery discs. I can see that partition from disk management only. But how do I boot from it? Some months ago I have linux os installed. So when the laptop boot up I can see that partition. But not Now. How to boot from it? I can't see that drive when i press F12. F2 = enter BIOS setup F8 = Boot in safe mode F12 = choose the boot drive

    Read the article

  • How to disable monitor "sleep" on Ubuntu without access to X?

    - by exhuma
    I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

    Read the article

  • My 386sx refuses to start in cold days

    - by Armadillo
    My old computer refuses to start in cold days. So, in really hot days (about 40ºC / 104ºF ) or even hotter, this PC usually starts, but in cold days, it wont. When the temperature is not in the "sweet-spot" the power light turns on for an half a second and then the computer turns off. But when it's really cold, not even the power light turns on, nor even a blink. Sometimes I use an Hair dryer, pointed directly to the PSU and that works great. 5 to 10 minutes is enough, depending on the ambient temperature. I think something is going wrong in my AT power supply. I can't replace this PSU for another because it has a non-standard size and connectors to power the motherboard. Does anybody have a clue about what it's failing in my PSU, so I can change that component (resistor, capacitor, ??, etc) and rock on with my 80386? Thanks

    Read the article

  • House Wiring for Ethernet/Coax/Power

    - by Adam Kragt
    Hoping this is the right place to post, the rest didn't seem to fit. If not, I apologize. Remodeling my house and want to wire up each room with Ethernet/coax wall ports. Both Ethernet, coax and power will be running through the sub-floor. I've read that there needs to be 2 ft between power cables and Ethernet to limit/prevent interference. Is this true? If not, does anyone know what the distance is? Thanks!

    Read the article

  • PC doesn't POST with a certain model of PSU

    - by Core Xii
    I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

    Read the article

  • Shut down by pressing the power button twice

    - by iHarry
    I have set my laptop's power button to shut down the computer when it is pressed (Windows 7 x86). But I often hit the button accidentally, and it's a rare case that I'm able to actually prevent it from shutting down. I don't want to disable it though. Is there a way so that I get a confirmation whether I really want to shut down the computer (just like in Mac OS X Lion, where a confirmation appears when the power button is pressed)?. Is there some way to bring the same to Windows 7 (and 8)?

    Read the article

  • Which type of motherboard i should buy and why?

    - by metal gear solid
    If budged is not a problem. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor? Is the size of motherboard and number of Slots only difference between all form factors? Is there any differences among form factors, related to performance of motherboard? Is bigger in Size (ATX) motherboard always better? Is it so smaller in Size motherboard will consume less power? What are pros and cons of each Form factor? What there are so many Form factor were created?

    Read the article

  • APC UPS-5000 Power off remote servers

    - by Vishal
    Hi there, I have a UPS connected via the serial port to a server using PowerChute Business Edition. If a power outage occurs I would like this server to start shutting down all other servers within the network. Is there dedicated software to do this? I was thinking of creating a command file which runs a .bat file to run shut down commands to each server (using PSExec). I can set PowerChute to run this command file when a power failure occurs. Is there not anything APC provide which has this functionality and is more efficient than writing a .bat file to do this? Thanks,

    Read the article

  • Any reasonable UPS for a Desktop PC, just to shut it down?

    - by Michael Stum
    While I do have a surge protector to protect against overvoltage (hopefully), I have nothing against undervoltage. When a lightning storm hits, I had the lights flickering at some point. The PC continued to run, but it got me thinking of getting a UPS as a way to a) have a clean 120V/60Hz power source and b) have a way to shut down the PC in case something bad happens. I heard not all UPS' protect against power spikes, so I wonder if someone has a recommendation? It does not need to keep the PC on for a long time if the power goes out, it's good enough if it shuts down the PC after 5 minutes or so. There are 2 PCs connected. One is a Core i7-860 with a Radeon 5870 running Windows 7 Ultimate (so quite power hungry. It uses a 600W PSU but I have no measurements of the actual usage), the other one is a Windoes Home Server, running WHS/Windows Server 2003. Any recommendations in the low-price segment?

    Read the article

  • How can I tell if my UPS is functioning properly or not for my PC?

    - by prabha
    For the last two days, my Uninterruptable Power Supply (UPS) has failed to produce the actual back up. So, I charged it for 24hrs and again checked that when the power failed my PC was automatically shut down. But in the time of power no supply from ups bt .......is my ups is working properly or not else there is direct power. It will cause any harm to my pc. my questions are..... Is the UPS functioning properly or not? If not, then will it harm my pc? If it is functioning, will it regulate direct power to pc without any cause? Is my UPS battery not working? What should I do to make my UPS batteries last for at least a year? I am using FRONTECH UPS 600va (Warranty for both ups and battery is expired) I already changed the battery 8 months previously. Note from editor: Tried to make as much sense of this question as I could. I hope I didn't alter the meaning in any way.

    Read the article

  • Which type of motherboard i should by and why?

    - by metal gear solid
    If budged is not matter. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor? Is the size of motherboard and number of Slots only difference between all form factors? Is there any difference related to performance of motherboard? Is bigger in Size (ATX) motherboard always better?

    Read the article

  • Which type of Form factor (motherboard) i should buy and why?

    - by metal gear solid
    If budged is not a problem. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor, should i purchase PSU according to Form factor of motherboard? Is the size of motherboard and number of Slots only difference between all form factors? Is there any differences among form factors, related to performance of motherboard? Is bigger in Size (ATX) motherboard always better? Is it so smaller in Size motherboard will consume less power? What are pros and cons of each Form factor? What there are so many Form factor were created?

    Read the article

  • Soft lockup after upgrade - cannot install from live CD

    - by nbm
    I dual-boot MacIntel Core 2 duo. nVidia graphics. Ran upgrade from ubuntu 13.10 to 14.04 (64 bit). On restart ran into {numbers} Bug: soft lockup - CPU#0 stuck for 22s! [swapper/0:1] Tried loading earlier kernel: same problem Tried re-installing ubuntu from a liveCD that has worked in the past: version 13.04. Same problem. Tried re-partitioning hard drive using Mac OS X disk utility and then installing ubuntu 14.04LTS from liveCD. Same problem. Not possible to verify liveCD disk (creates same "soft lockup" bug.) Tried installing from the liveCD with version 13.04 that I know works (that's how I got Ubuntu on this machine in the first place.) Same problem. I know this is not a hardware problem as OS X works just fine, I am using it right now on the same machine. I have been using various versions of Ubuntu for 2 years. Things I cannot do: Open a terminal Verify CD image Start ubuntu from CD (same soft lockup problem) This problem is similar to some other questions, none of which have been satisfactorily answered: Ubuntu 14.04 soft lockup on Vostro 3500 Cannot do fresh install of Ubuntu 13.04 while booting from DVD: "soft lockup" bug Live CD stalls when installing Ubuntu 13.10 UPDATE 6/11/14: Following some much-appreciated advice from bain (see below) I burned a 12.04LTS disk and started with kernel parameters: noapic, no1apic, acpi=off, nomodeset, elevator=deadline, and clocksource=jiffies. With all of these parameters I was able to load the 12.04LTS CD ("Try without installing"). It worked fine. However, as soon as I tried to install Ubuntu from the CD, my wired ethernet (eth0) connection would hang. There are already various askubuntu questions and bug reports about this problem, none of which had answers for me. (E.g., dhclient eth0 does nothing, none of the various reset commands does anything, manually setting IP &etc does nothing. I could reliably kill the ethernet connection by clicking "install ubuntu" every single time.) I could go ahead and install 12.04 without an internet connection, but the install would freeze after mostly completing (I tried several times.) There were some relevant error messages in the details of the install output script that, IIRC, had to do with searching for missing files and not being able to access eth0 (internet) to get them. To be honest I gave up at that point and I'm not sure I wrote those down. If I find some notes I will post them. At this point I no longer have Ubuntu on my system. I wiped the partitions and am using exclusively OS X. I am leaving this question in case it helps anyone else with similar problems. I love open source and I love Linux, and the next machine I get I will probably just build from Arch. At the moment I miss repositories and a lot of other things about Ubuntu, but the OS X terminal is 'nix, I can pretty much use all the open source apps I like, and while I am not a fan of the Apple software it gets the job done for me. Unlike Ubuntu, which can't even install. I realize this isn't necessarily a place for a soapbox speech, but when I first installed 12.04 several years ago there were already people in the community complaining that Canonical was going too "commercial". But I loved it. Several years later and all I've seen is Canonical adding more not-so-useful bells and whistles to Ubuntu while continually failing to fix basic problems on upgrades. With a dual-boot (and sometimes triple-boot) system it always took me some tweaking to get an upgrade to work, and to some extent that is okay. But at this point I feel like Canonical ought to just put a price tag on Ubuntu. All I see is more commercialism and advertising and product tie-ins, and ongoing problems do not get fixed. I am a big fan of open-source, not-for profit enterprise. I am also a big fan of for-profit enterprise, which certainly has its place and usefulness. I am not a fan of companies who pretend to be in favor of open source but really are just out to make a buck, and IMNSHO that is what Canonical has become. This is a great community and I wish you all the best, but my next install of Linux will not be Ubuntu.

    Read the article

  • Is it possible to boot already installed version of Ubuntu from within Win7, e.g. with a vm?

    - by Fizzik
    I have both Ubuntu 12.10 and Win7 installed. I use the former mostly for scientific simulations and the latter for applications. The problem I came across with this configuration is that the simulations take quite a while, and I'm not satisfied enough with solutions like Wine to run the Windows apps while the simulation runs. I would rather not install the simulation programs again, since it took quite an effort. So, is it possible to boot the already installed version of Ubuntu from within Windows 7 via VirtualBox or or something else?

    Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >