Search Results

Search found 14873 results on 595 pages for 'hard drives'.

Page 93/595 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• How should I configure grub for booting linux kernel from a USB hard drive?

  - by skolima

  I have a laptop hard drive in an external enclosure which I use as a large pendrive. For an added twist, I have installed Linux on it, so I can boot any machine with my distribution of choice (e.g. for data recovery or repairing a b0rked system or just using a borrowed laptop without destroying the preinstalled Windows). The problem is that, depending on the hardware configuration, the USB hard drive may be visible under different paths. For grub configuration I just use (hda0,0) as it is relative to the device the grub was launched from. I have UUID entries in /etc/fstab. I also specify rootwait in the kernel parameters so that it waits for the USB subsystem to settle down before trying to mount the device. What should I pass to the kernel as root= ? Currently boot from the pendrive once, check the debug messages to see what /dev/sdX device has been assigned to the USB drive by the kernel, then reboot and edit the grub configuration. I can't change anything on the PC besides enabling Boot from USB hard drive in BIOS and setting it to higher priority than internal hard drives. There are various initrd generating scripts which include support for UUID in root device path, unfortunately the Gentoo native one (genkernel) does not support rootwait and I had no luck trying to use others. The boot process goes like this (it is quite similar in Windows): The BIOS chooses the boot device and loads whatever is its MBR (which happens to be grub stage-1). Grub loads it's configuration and stage-2 files from device it has set as root, using (hd0) for the device it was loaded from by BIOS. Grub loads and starts a kernel (still the same numbering, so I can use (hd0,0) again ). Kernel initializes all built-in devices (rootwait does it's magic now). Kernel mounts the partition it was passed as root (this is a kernel parameter, not grub parameter). init.d starts the userland booting process, including mounting things from /etc/fstab. Part 5 is the one giving me problems.

  Read the article

• Can the Dell PowerEdge T320 boot from a USB stick in hard drive emulation mode?

  - by Icydog

  I am trying to install FreeNAS on a Dell PowerEdge T320. I've followed the instructions here (http://doc.freenas.org/index.php/Burning_an_IMG_File) to write the .img file to four different USB sticks with dd if=FreeNAS-9.2.1.5-RELEASE-x64.img of=/dev/sde, but I can't boot off of any of them. When I try to boot, I get the following screen: F1 FreeBSD F2 FreeBSD F3 Drive 0 Then it auto-selects F1 and either prints # about once a second forever, or it sits with a blinking cursor doing nothing. Forum posts and the wiki page linked above say to set the USB boot emulation mode to hard disk (as opposed to auto or CD/DVD/floppy), and older Dell PowerEdge models including the T310 have this option in the BIOS settings, but I cannot find it on the T320 with the latest BIOS 2.1.2. I have even tried writing the USB image to a USB hard disk, but with the same lack of success. Has anyone been able to find this USB boot setting on a T320, or been able to boot FreeNAS/FreeBSD from USB in some other way on a T320?

  Read the article

• Does the Win XP/7 dual boot "missing restore points" problem apply to systems with separate hard disks for each O/S?

  - by Robert Oschler

  I'm in the process of installing Windows 7/64 on a system with Windows XP/32 on it. During my research, I read about a problem that occurs in the dual boot scenario where Windows XP deletes Windows 7's restore points when it accesses the Windows 7 volume: http://support.microsoft.com/kb/926185 I found a workaround but it seems pretty painful since it appears to involve using the registry to make the Windows 7 volume appear invisible or "offline" to Windows XP, making sharing disk data between the two O/S annoying since you have to use something like an external storage device to get it done: http://www.vistax64.com/tutorials/127417-system-restore-points-stop-xp-dual-boot-delete.html I was wondering if this problem only occurs with systems that have both O/S installed on the same physical hard drive (in different partitions)? In my case, I will have each O/S on a completely separate physical hard drive. Any other tips would be appreciated. -- roschler

  Read the article

• Iomega Home Media Network Hard Drive: Accesing the data in the disk?

  - by JJarava

  Hi all! I have an Iomega Home Media Network Hard Drive, 1TB, and lately I can't access the data on the drive. The shares (both built-in and created by me) are there, the security works, but when trying to access the data I get a "The network path was not found" message which is worrying, to say the least. I'd like to know if there is a way to get the data off the disks somehow, as some of the data in the drive (ie, pictures and videos of my 1.5 yrs old son) is hard if not impossible to find otherwise. Thanks a lot Javier

  Read the article

• Exchange Server 2007 Setup

  - by AlamedaDad

  Hi, I'm working on a upgrade to Exchange 2007 and I wanted to get some advise on hardware choices. We currently have an Exchange 2003 STD server with 400 users split between 6 AD Sites, that is housed on a single server. We need to move to a redundant, fault tolerant system to support our users. I'm planning on installing 2 Dell 1950 servers with W2k8-std to act as CAS and Hub servers, with NLB to allow abstraction of the actual server name to the users. There won't be an edge system since we have a Barracuda box already that will handle in/out spam/virus filtering. Backend I'm planning on 2 mailbox servers which will be Dell 2950s with 16GB RAM, 2 either dual-core or quad-core CPUs and 6 300GB SAS drives in some RAID config. These systems will be clustered using W2k8 Ent clustering and running CCR in Exchange. My questions are as follows: Is 16GB enough RAM for serving that many mailboxes along with the windows clustering and ccr? I'm trying to figure out disk layouts and I'm unsure of whether to use all local disk or some local and some SAN, via an OpenFiler iSCSI server. The SAN would be a Dell 2850 with 6 - 300GB SCSI drives and a PERC controller to slice as I want, with 8GB RAM. Option 1: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 1 - Mail stores Option 2: 2 drives, RAID 1 - OS and logs 4 drives, RAID 5 - Mail Stores and scratch space for eseutil. Option 3: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 0 - scratch space ~300GB iSCSI volume for mail stores Option 4: 2 drives, RAID 1 - OS 4 drives, RAID 5 - scratch space ~300GB iSCSI volume for mail stores ~300GB iSCSI volume for logs I have 2 sockets for CPUs and need to chose between dual and quad cores. The dual core have faster clocks but less cache and I'm thinking older architecture. Am I better off with more cores and cache while sacraficing clock speed? I am planning on adding the new E2K7 cluster to the E2K3 server and then move each mailbox over, all at once, then remove the old server. This seems more complicated than simply getting rid of the 2003 server and then adding the 2007 cluster and restoring the mailboxes using PowerControls or exmerge. The migration option lets me do this on my time, where a cutover means it all needs to work at once. If I go with the cutover method, how can I prebuild the servers and add them to the domain right after removing the 2003 server, or can't I? I think the answer is no and the migration is my only real option if I want to prebuild. I need to also migrate about 30GB of Public Folders. Is there anything special about this, other than specifying in the E2K7 install that I want older Outlook clients and PF's setup? I guess I could even keep the E2K3 server to host just the PFs? Lastly, if I have a mix of Outlook 200, 2003 and 2007 what do I need to do to make sure they all have access to the GAL and OAB? At time of cutover, we'll be at like 90% 2007, but we will have some older stuff around. My plan is to use Outlook Anywhere on laptops that are used outside the physical network. Are there any gotchas involved in that? I'm even thinking about using is for all Outlook clients, does anyone do that? The reason I'm considering it is that our WAN is really VPN tunnels over internet connections, so not a fully messhed, stable WAN. Thank you all very much for the assistance in advance and I look forward to discussion of these points! Regards...Michael

  Read the article

• Best alternatives to recover lost directories in FAT32 external hard drive?

  - by Sergio

  Hi: I have an 320 GB ADATA CH91 external hard drive. I guess it has some problems with the connector of the USB jack. The point is that in certain occasions it fails in write operations generating data losses. Right now I lost a directory with several GB's of very useful information. Since then I have not attempted to write to the disk any more. What tool would you recommend to recover the lost data? The disk is FAT32 formatted (only one partition) and I use both Linux and Windows. What filesystem format would you recommend to avoid future data losses? I currently only use this external hard drive in Linux so there are several available choices (FAT, NTFS, ext3, ext4, reiser, etc.). Regards, Sergio

  Read the article

• sfdisk restore partition table if two hardisk have different sizes

  - by MA1

  What will happen if i try to restore the partition table of a larger hard disk to smaller hard disk, for example: partition table of 250GB hard disk to a 80GB hard disk using sfdisk like this. sfdisk /dev/sda < PartitionTable250.txt Will sfdisk detect it? I think there will be no problem if the partition table of a smaller hard disk is going to be restored on a larger hard disk?

  Read the article

• Physically moving a hard drive from older iMac (c2d) to new iMac (i7) ?

  - by Inshim

  Instead of my usual habit of using superduper to mirror my drive to a new computer, I just physically moved the hard drive from an older iMac to a new one. But... it now doesn't boot, getting stuck at the apple logo screen. Since the hard drive that came with the new iMac works well, and my old drive works well when I return it to the older iMac, I conclude that there is some problem at the system/kernel level due to the different hardware. In the past I did similar things (e.g. starting a C2D machine from a Core Duo in target disk mode), so perhaps the change in architecture to the i5/i7 is too problematic? The main point: do you know of any way to get the system to rebuild for itself the proper versions of the system components when booting? Are there certain directories that I can safely delete to make that happen? Thanks

  Read the article

• I used my ntfs formatted hard drive, copied files from a mac using a bridge program, but now i can't

  - by Marc

  I used my ntfs formatted hard drive, copied files from a mac using a bridge program, but now i can't see any of the files on my pc help? I brought it from home, (NTFS HD) found that it was only read only.. so i got a bridge program (don't remember) and was able to copy files from the mac to the hard drive. I took it home and went to get into those files, and they do not even show up.. it copied, and did everything it was supposed to do to let me know it was working, but now i can't find any of those files. am I FUBAR? :(

  Read the article

• Can't change permission/ownership/group of external hard drive on Ubuntu.

  - by MikeN

  I have an external hard drive connected to my Linux box. I wanted to setup a web server to access files on it, but the permission on all files and directories on the drive are "rwx" for the owner which is my local login, and the group is the "root" group. I need the files readable by the apache user, I was trying to set all files to be "chmod a+rwx -R *", but this doesn't do anything (gives no errros, just has no effect.) I tried chaning the group using "chgrp" to my user group, but that won't work either, it gives me errors that I lack permission even when I run all those commands as sudo! What's up with this hard drive??? "sudo chmod a+rwx *" should work on anything, right?

  Read the article

• machine crash when connecting to external harddisk

  - by Gnot

  i recently had a problem with my laptop. when i booted up the machine, i would get a SMART failure error message and when i pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. thinking that my hard disk was dying, i bought a new hard disk and installed on my laptop and so now my laptop is alright. however i need to recover data from that old hard disk, so i bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. the first few times when i connected, i could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. but now whenever i connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. do you think my old hard disk is dead beyond repair? or you can offer some help here? any assistance would be appreciated!

  Read the article

• Moving files from Public folder to C: takes a minute, even though they are same hard drive and same

  - by Jian Lin

  I have a big file, like 2GB, and would like to move it from Network -> Bookroom -> Users -> Public (this is the computer in the bookroom in the house) to c:\myfiles and they are actually on the SAME hard drive (and same partition). But copying still takes a minute or so? I thought if on the same hard drive and partition, then it is a "move" and it should take 2, 3 seconds only. that public folder also is \\Bookroom\Users\Public Update: Sorry, I actually mean "move" all the way... so it is not copy but move. So that's why I thought it should take 2, 3 seconds only.

  Read the article

• Has anyone had luck getting an external hard drive working with a PCMCIA USB card?

  - by Carl

  I would like to know if anyone has had any success in getting and external 2.5" IDE hard drive in an external case (w/USB cable) working when plugged into a PCMCIA USB card. My hard drive doesn't work when plugged into my HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My MP3 player will work fine when plugged into it. I tried plugging in both of the USB cables that are one one end (Y cable), and it doesn't make a difference. I read the problem may be insufficient power.

  Read the article

• Copying files from Public folder to C: takes a minute, even though they are same hard drive and same

  - by Jian Lin

  I have a big file, like 2GB, and would like to copy it from Network -> Bookroom -> Users -> Public (this is the computer in the bookroom in the house) to c:\myfiles and they are actually on the SAME hard drive (and same partition). But copying still takes a minute or so? I thought if on the same hard drive and partition, then it is a "move" and it should take 2, 3 seconds only. that public folder also is \\Bookroom\Users\Public

  Read the article

• DISK BOOT FAILURE after upgrading power supply

  - by Phenom

  After upgrading my power supply, I get the following error message when trying to boot into Windows 7. DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER My Windows 7 installation is on a SATA hard drive. I'm able to fix this problem if I hook up my IDE hard drive, then it boots the SATA hard drive fine. I don't like this solution though because then that means my IDE hard drive is drawing power even though it isn't being used. Why would a newer power supply need the IDE hard drive hooked up just to boot into the SATA hard drive? There are no boot files on the IDE hard drive; it is completely empty. My old power supply did not need it hooked up in order to boot the SATA hard drive.

  Read the article

• How to configure Time Machine to also backup an connected external hard drive?

  - by Another Registered User

  I've inserted a sweet SSD into my MacBook Pro, but it had limited space. So I had to export 60 GB of Data to an external hard drive. But now, when I run TimeMachine to backup my stuff, of course it only backups what's on the system disk. Is there a way how to also backup the connected external hard drive together with TimeMachine? Maybe there's a trick to get this work, with a fake folder that's actually the mounted drive? What could I do?

  Read the article

• Laptop crashes when connecting to external harddisk

  - by Gnot

  I recently had a problem with my laptop. when I booted up the machine, I would get a SMART failure error message and when I pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. Thinking that my hard disk was dying, I bought a new hard disk and installed on my laptop and so now my laptop is alright. However I need to recover data from that old hard disk, so I bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. The first few times when I connected, I could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. But now whenever I connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. Do you think my old hard disk is dead beyond repair? Or you can offer some help here? Any assistance would be appreciated!

  Read the article

• How do I get a USB hard-disk adaper to work with a PCMCIA USB card?

  - by Carl

  I have a PCMCIA (Cardbus) 32bit USB 2.0 2-port card. If I plug my MP3 player in it works fine. I have a USB adapter for a hard disk drive. When I plug that into the PCMCIA USB slot the light on that hard disk flashed between red and green - it should stay green. "USB Mass Storage device" is added in the Device Manager, but no drive letter appears in My Computer. The installing device icon down by the clock never goes away. (Windows XP SP3.)

  Read the article

• Best alternatives to recover lost directories in FAT32 external hard drive?

  - by Sergio

  I have an 320 GB ADATA CH91 external hard drive. I guess it has some problems with the connector of the USB jack. The point is that in certain occasions it fails in write operations generating data losses. Right now I lost a directory with several GB's of very useful information. Since then I have not attempted to write to the disk any more. What tool would you recommend to recover the lost data? The disk is FAT32 formatted (only one partition) and I use both Linux and Windows. What filesystem format would you recommend to avoid future data losses? I currently only use this external hard drive in Linux so there are several available choices (FAT, NTFS, ext3, ext4, reiser, etc.).

  Read the article

• I know this is a stupid question but... How many websites can my server potentially hold?

  - by Daniel Kindler

  Sorry for the "noob" question, but... About how many medium-sized websites with average traffic could this server hold? Just like the average website, kind of like a small business site. How many sites could this server hold, but still maintain nice, decent speed? PowerEdge R510 PE R510 Chassis for Up to Four 3.5" Cabled Hard Drives, LED edit Processor Intel® Xeon® E5630 2.53Ghz, 12M Cache,Turbo, HT, 1066MHz Max Mem edit Memory 8GB Memory (4x2GB), 1333MHz Single Ranked UDIMMs for 1 Procs, Optimized edit Operating System SUSE Linux Enterprise Server 10, SP3, Up To 32 CPU Lic, 1 YR Sub, DIB, Media edit Red Hat Enterprise Linux Licensing Hard Drives 250GB 7.2K RPM SATA 3.5" Cabled Hard Drive edit Hard Drives 1TB 7.2K RPM SATA 3.5" Cabled Hard Drive edit Hard Drives 2 X 2TB 7.2K RPM SATA 3.5in Cabled Hard Drive Hard Drive Configuration No RAID, Embedded SATA Controller for x4 Chassis edit Power Supply 480 Watt Non-Redundant Power Supply edit Thank you!

  Read the article

• How many websites can my server potentially hold?

  - by Daniel Kindler

  Sorry for the "noob" question, but... About how many medium-sized websites with average traffic could this server hold? Just like the average website, kind of like a small business site. How many sites could this server hold, but still maintain nice, decent speed? PowerEdge R510 PE R510 Chassis for Up to Four 3.5" Cabled Hard Drives, LED edit Processor Intel® Xeon® E5630 2.53Ghz, 12M Cache,Turbo, HT, 1066MHz Max Mem edit Memory 8GB Memory (4x2GB), 1333MHz Single Ranked UDIMMs for 1 Procs, Optimized edit Operating System SUSE Linux Enterprise Server 10, SP3, Up To 32 CPU Lic, 1 YR Sub, DIB, Media edit Red Hat Enterprise Linux Licensing Hard Drives 250GB 7.2K RPM SATA 3.5" Cabled Hard Drive edit Hard Drives 1TB 7.2K RPM SATA 3.5" Cabled Hard Drive edit Hard Drives 2 X 2TB 7.2K RPM SATA 3.5in Cabled Hard Drive Hard Drive Configuration No RAID, Embedded SATA Controller for x4 Chassis edit Power Supply 480 Watt Non-Redundant Power Supply edit Thank you!

  Read the article

• I have a "ghost drive" Local Disk (Q:) under my "Hard Disk Drives" category which cannot be deleted

  - by Fabian

  I think it happened after I connected my dad's external hard drive to my PC. Its capacity is 0 bytes, it cannot be formatted, and under Disk Management I can't find it. How do I remove it?

  Read the article

• How do you do the offsite hard drive backups?

  - by kentchen

  I have been doing hard drive backups for a while, which I believe a lot of you guys do as well, but am having trouble figuring out a better way storing them offsite. I am wondering how you guys out there do that. Any policy or tips & tricks when it comes to offsite store your backups, mainly hard drives not tapes. Thanks in advance. [update] Thanks for mentioning the online backup. We are actually in the middle of this process. And I 100% agree that it's the ultimate way to go. However, considering the cost, sometimes it may not be the option, as it's a quite expensive option if you also consider the application level. I guess online backup can be a very good one in the separate topic. :)

  Read the article

• PC won't boot, even into bios

  - by divided

  Here's the deal: I cleaned a hard drive of some viruses (externally) and put it back into the original pc. This hard drive will boot in any other pc except the original pc. When I try other hard drives in the original pc, they are able to boot. The drive has Windows XP. What is the problem? How can I get this hard drive to work properly? The original hard drive works in other PCs. The PC boots with other hard drives acting as the master. If I boot with no hard drive, I still can't get into the BIOS These are all IDE hard drives The PC doesn't beep, it just boots into a black screen with a cursor blinking in the upper left of the screen

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >