Search Results

Search found 2489 results on 100 pages for 'hp laserjet'.

Page 93/100 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Proper end of day sequence to maintain monitor config

  - by WarmBeer

  I've got an HP EliteBook 6930p that travels from home, where it is connected to individual cables, and work where there is a docking station. At both locations I have an external monitor as the secondary monitor and like to have the laptop screen as the primary, i.e. with the task bar. At the end of the day I close the laptop, which is supposed to set it to standby. When I get home I plug in the power cord and the external monitor cord and open the computer. When heading into work I close the computer and unplug everything. Inevitably when I open the computer at the new location the monitors are reversed, i.e. the primary, task bar display is on the external monitor and the laptop shows the secondary, even though when i click identify the laptop has the 1. I then have to disable the secondary display, switch the primary to the laptop and re-enable the secondary. I've tried locking the computer before closing and occasionally that works to keep the setup in place but not always. Any suggestions for how to keep the config in place during transport? ed

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Touchpad does not respond when I am holding key on the keyboard

  - by Tadeck

  I am experiencing strange problem with using my touchpad and keyboard simultaneously under Windows 7. I have HP tx2550ew (convertible tablet), and when I hold some key under Windows 7 (eg. space, a, s etc.), the touchpad seems to be blocking. I spotted this while playing Counter Strike. I am not playing much games, and I haven't been playing CS since January, so I am not sure when it started behaving like that. I have tested it also outside the game - when I hold space (eg. when on some web page and entering text into input field) or some letter key, the cursor is not able to move. The problem seems to not be occuring when I hold Shift, Ctrl nor Alt. Did any of you experience similar problem? Do you know what may have caused this? Is there any way I could check what is wrong with my laptop? I have been looking for a solution, but it seems I haven't been looking in right places. This is why I ask question here. Ps. I am unable to test whether this is touchpad-specific, because I have no mouse at my disposal at the moment (got used to touchpad so much I even find it more efficient and haven't been using a mouse with my laptop for months).

  Read the article

• Is there any way to limit the turbo boost speed / intensity on i7 lap?

  - by Anonymous

  I've just got a used i7 laptop, one of these overheating pavilions from HP with quad cores. And I really want to find a compromise between the temp and performance. If I use linpack, or some other heavy benchmark, the temp easily gets to 95+, and having a TJ of 100 Degrees, for a 2630QM model, it really gets me throttling, that no cooling pad or even an industrial fan could solve. I figured later that it is due to turbo boost, and if I set my power settings to use 99% of the CPU instead of 100%, and it seems to disable the turbo boost, so the temp gets better. But then again it loses quite a bit of performance. The regular clock is 2GHz, and in turbo boost it gets to 2.6Ghz, but I just wonder if I could limit it to around 2.3Ghz, that would be a real nice thing. Also there is another question I've hard time getting answer to. It seems to me that clocks are very quickly boosting up to max even when not needed, eg, it's ok if the CPU has 0% load, the clocks get to their 800MHz, but even if it gets to about 5% it quickly jumps to a max and even popping up turbo, which seems very strange to me. So I wonder if there is any way to adjust the sensitivity of the Speed Step feature. I believe it would be more logical to demand increased clock if it hits let's say 50% load. I do understand that most of these features are probably hardwired somewhere in the CPU itself or the MB, which has no tuning options just like on many laptops. But I would appreciate if you could recommend some thing, or some software. Thanks

  Read the article

• What is the proper way of debugging a slow Windows installation?

  - by Niklas

  You know the drill - you've been asked to check why you cousin's computer is running slow. I was there yesterday. Being a Mac user since 2007 I haven't really dug deep in Windows internals in the past five years. Googling for answers reveals many, many different answers: broken registry, spyware, antivirus program, fragmented disk, turning of visual effects etc. In this particular case I was asked to look at a two year old HP laptop with Vista. Windows was running incredibly slow and even opening up a new explorer window took almost a minute. I ended up doing everything of the above: running cc cleaner, defragmenting the disk, turning off visual effects, turning off norton and a bunch of other things people believe have an impact on Windows performance. Now I'd like to understand this in depth. Is there a proper, "scientific" if you so will, way of debugging and understanding where the problem with a slow running Windows installation lies? (In my particular case this concerned Windows Vista but let's try to create general guide for XP and Windows 7 too). To me, it seems wrong to just run a bunch of different tools without understanding the underlying cause of the error.

  Read the article

• Looking for way to log process terminations on OS X (Mac)

  - by Stan Sieler

  I'm looking for a way to log all process terminations on my Mac (OS X 10.6.8). (And see pid, timestamp, process name) I've implemented something similar for HP-UX, but it required a kernel-level driver and intercepting several variations of "exit()" (the normal one, and the one invoked on behalf of a process while it's aborting). Why do I want the info? I've been seeing messages in my system log file (dmesg) like: CODE SIGNING: cs_invalid_page(0x1000): p=91550[GoogleSoftwareUp] clearing CS_VALID CODE SIGNING: cs_invalid_page(0x1000): p=92088[GoogleSoftwareUp] clearing CS_VALID Although dmesg lacks timestamps, apps/Utilities/Console : Database : all : search for CS_VALID shows that the messages appears about once every 58 1/2 minutes. I suspect the number after "p=" is a process id (pid) ... but for a process that has long since terminated by the time I see the message. So, if there was a process termination log mechanism that recorded the pid, the time of termination, the reason for termination, and the process name (at time of termination), that would probably allow me to determine who's causing those errors to be logged! (No, I'm not running Chrome on my Mac, and "ps -ef | grep -i goog" gets no hits either ... I'm not consciously running any Google apps on the Mac) thanks, Stan [email protected]

  Read the article

• How can I get Windows 8 to automatically disable touch when I am using my Wacom pen and turn it back on when I am not

  - by Robert

  I have an HP convertible tablet computer which I just upgraded to Windows 8. The problem (which existed under Windows 7 as well) is that this tablet has both a capacitive touch screen (with multi-touch) AND a wacom-type tablet built in to the screen that works using electro-magnetic resonance with the provided stylus. My Use Case: Most of the time I am happy using my fingers and the touch interface for navigation and whatnot. However, when I want to get down to serious note-taking/drawing, I want to use the wacom functionality. The problem is that any comfortable writing position has me resting my arm/hand on the screen, which activates the touch technology (despite supposed palm-detection algorithms) and completely screws up my input paradigm. My Ideal Solution: Ideallly, since wacom technology senses when the pen is "close" to the screen, I would love to have touch be automatically disabled whenever the wacom pen is detected, and turned back on when it is out of range. this would allow me to seamless switch between the two input methods, and since I NEVER want to use both at once would work perfectly for me. An acceptable alternative: As a next best option, It would be great to be able to turn off the touch functionality (leaving the wacom in place) whenever I entered specific apps (e.g. OneNote, Photoshop, Gimp, Pencil, etc.) and then have it turn back on when I left that app.... As a worst case at least lets me use my PC option: If I could create a shortcut (tile or otherwise) that flips the touch on and off without going all the way through the nested computer settings, that would be better than nothing. Thanks in advance for the help with 1 or more of the above.

  Read the article

• Copying files between linux machines with strong authentication but without encryption

  - by Zizzencs

  I'm looking for a suitable program to copy files from one linux machine to another one. The program should be able to do authentication but it should not do encryption. The reason behind the latter is the lack of CPU power to do the encryption. I copy backups from ~70 machines to a single backup server simultaneously. The single server is an HP Proliant DL360 G7, with 10 Gbps ethernet connection and an FC storage backend that can do 4 Gbps. Through FTP I can write ~400MB/sec to the storage (that's about what I want) but through ssh with arcfour I can only do ~100MB/sec while having 100% CPU usage. That's why I want file transfers not to be encrypted. The alternatives that I found not really suitable: rcp: no authentication, forget it FTP: making the authentication "secure" (at least preventing plain-text password exchange) is possible but not really easy and I haven't found a method to force any FTP daemon to encrypt the control channel (for the authentication) and not to encrypt the data channel (for data transfers) SCP/SFTP: in farely recent ssh(d) implementations you can't turn off encryption. The best you can do is to use the arcfour cypher for the encryption but it sill uses too much CPU power for my needs. rsync over ssh: same problems as with SCP/SFTP. plain rsync: from the documentation of rsyncd: "The authentication protocol used in rsync is a 128 bit MD4 based challenge response system. This is fairly weak protection, though (with at least one brute-force hash-finding algorithm publicly available), so if you want really top-quality security, then I recommend that you run rsync over ssh." It's a no-go. Is there a protocol/program that can do exactly what I want? (A big plus would be if it could work on windows as well and/or if it would support rsync-stlye copying/synchronization (e.g. copy only the differences).)

  Read the article

• Trobleshooting extremely slow opening times in Win7 for documents on Win2k8 server

  - by Mazupan

  Hello. It's hard even to describe my problem. It seems there's only problem with extreme slow openings (up to 10 minutes) on Windows 7 (on XP things works fine) for files that are stored on Windows Server 2008. And now what I discovered up till now. If I open (some files, not all, not allways) .doc and .xls files with doubleclicking it takes up to 10 minutes to finaly open the file. In that time, file seems to be locked for all other users. If I cancel opening, file remains locked for some time. Owner on that files is the one who last wrote changes in them. If I change the owner to larger group, which I am member of file gets opened super fast. When opened file can be saved normaly and fast. That file reopens fast. One other user reports that there is only problem when opening the files for the first time in a day. When he openes first file he has no problems with other files at all (or so he says). He also states that when accessing files from home via VPN he has no such problems with files. And now: anybody has a clue where to start looking? I suppose that is misconfiguration problem. But where? File system? Permissions? DFS? VMWare network config? My setup is as follows: Physical server: HP Prolian ML350 G6 Virtual host: VMWare ESXi 4 Guest: Windows Server 2008 Standard Files are accessed via DFS shares. Please help me. Thanks. Mazupan

  Read the article

• Mac OS X in Virtualbox says "You need to restart your computer"

  - by humoeba

  I've been trying to figure out for the past week how to get Snow Leopard reliably running in a VM. Right now I am using VirtualBox, and it runs fine for a while, but every once in a while (happened 3 times in the last few hours) I get the "You need to restart your computer" message. Unfortunately, it hasn't even lasted long enough to finish installing the operating system yet. I first tried VMWare, which was a pain to set up. I got it running ok, operating system installed, with the guest tools. Every once in a while though, it just stops running. I click inside the VM, and there's no mouse. It doesn't respond to keyboard input either. I have to reset the VM to get a response. I'm wondering if this is the same error. This happens with both Workstation and Player. Here is the tutorial I used for VirtualBox: http://www.sysprobs.com/iboot-loader-virtualbox-install-snow-leopard Here's the tutorial I used for VMWare: http://bobhood.wordpress.com/2009/12/18/welcome-to-snow-leopard-mac-os-x-10-6-and-vmware-workstation-7/ I'm using an iso for Mac OS X 10.6.3. I have an HP Pavilion dm4 with an Intel Core i7 M640 running Windows 7; VT is turned on. Using VirtualBox 4.0.4 and VMWare Workstation 7.0.1 and VMWare Player 3.0.1 Does anyone know what might be causing this error or how I can fix it? Thanks.

  Read the article

• How to create a static IP on Windows Server 2008 R2 so I can access the server remotely

  - by Aesir

  I have just purchased a HP Proliant N40L which I am intending to use as a NAS, learning tool and just in general something to mess around with. As a student via the Microsoft dreamspark program I can get a free copy of Windows Server 2008 R2 which I am using as the OS. So that I can remote to the box from outside of my local network and so that I can stream media from it to my PS3, I have read that I need to create a static IP for the server and use port forwarding to forward to this IP so I can remote in. Is this correct? I am not really sure how to do this and if I need to make these changes on my router configuration, on the OS or both. I am a novice when it comes to networking however most resources for Windows server 2008 R2 seem to assume a fair amount of experience already. I realise that using this particular OS may seem like overkill for what I currently wish to do with it (stream content to other devices and backup) but as I can get a copy for free it seems sensible. Edit: From reading answers posted I feel I should give more information. I have now tried to add a static IP address using my router configuration settings. I have used the getmac command to get the mac address of the server. My ISP is Virgin Media and I have gone to the LAN IP section and I have added an IP address to the DHCP Reservation Lease Info. I can now use remote desktop connection internally to remote to the server (so I am assuming assigning this IP has worked). How do I configure this on the OS as well? I am also unsure on how I would remote to this machine outside of my local network?

  Read the article

• Ignore non-unicode programs language when installing software

  - by mitya

  This is something that is driving me nuts for a while and I haven't been able to find a solution for this problem anywhere. I am running Windows 7 and my "Language for non-Unicode programs" setting is set to Russian. I need for some non-unicode software that has a Russian UI. However, for most of my software I prefer to use the English UI. A lot of software out there is multilingual and is too smart for my liking. When installing, it switches the UI to Russian and the software UI stays in Russian after the installation without an option to change that, besides setting the "non-unicode language" to English. It switches back to Russian once I revert the setting and reboot. Most of the time it is driver software, i.e: Intel, HP, etc. How can force the installation to run English and stay that way after install, ignoring the "Language for non-Unicode programs" setting? Now, I understand this might be specific to the installer: MSI, Install Shield, etc. But any solution will be good, even if I have to apply it for every software installation. Thanks in advance for any helpful information!

  Read the article

• Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

  - by ZiGi

  i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

  Read the article

• What is the oldest hardware still in production use? How is it kept running?

  - by sleske

  In the spirit of the question What is your oldest hardware that still works?, I'd like to ask: What is the oldest hardware you know that is still in production use? And what challenges did you (or someone else) face in keeping it running (scarce documentation, no support, no spare parts available...)? Most organizations will retire / upgrade software and hardware after 5-10 years, but sometimes old software is kept running on old boxes, because it "just works". I once worked at a client site that was running a critical piece of (in-house developed) business software on a single server running HP-UX. The server was old (ca. 12-13 years), but fortunately still running without problems; however, getting spares would have been very difficult, and since software installation was undocumented, any significant system changes or even new hardware might have caused significant downtime and data loss. We eventually managed to replace it, but this is not always possible. I also read that many organizations still run decade-old mainframe hardware, particularly for highly customized systems controlling industrial machines or power plants. Which old hardware have you encountered? How did you manage these challenges? Related question: http://serverfault.com/questions/82467/should-old-servers-be-retired

  Read the article

• DVD-burner disappears when using grub

  - by drblah

  This is a rather annoying problem I have with Linux on my laptop. Whenever I install any Linux distro that relies on grub (which is about 99 % apparently) it will mess up my DVD-drive and the drive will not be recognized after booting, no matter the OS (Ubunntu, Arch, Windows Vista or 7). I know the problem has nothing to do the DVD-drive itself, because I bought a new one a few months ago. I am also sure that grub is messing the drive up, because I have tried to use LILO, which worked fine (except for horrible boot times.) This problem have persisted through about 3-4 years and it is a pretty bad show stopper whenever I want to work with Linux. I had hoped it would get fixed over time, but no one seems to have the exact problem I have. The drive is connected with an IDE connection. Update: The old drive was a Toshiba Samsung SN-S082. I don't know the model number of the new one, but it is HP (I think). Things I have tried to fix it: Mess about with some BIOS settings like enabling AHCI and change some IDE settings. Installing a different boot loader DOES fix the problem but I would like to use grub.

  Read the article

• Can not mount my USB disk-- Ubuntu nor windows[dmesg including]

  - by EthanZ6174

  first, here is my dmesn|tail result right after i plugged the disk: $ dmesg | tail [ 2578.697224] scsi 6:0:0:0: Direct-Access HP v100w PMAP PQ: 0 ANSI: 0 CCS [ 2578.698322] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 2578.916464] sd 6:0:0:0: [sdb] 3921920 512-byte logical blocks: (2.00 GB/1.87 GiB) [ 2578.916950] sd 6:0:0:0: [sdb] Write Protect is off [ 2578.916956] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 2578.916961] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922460] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922470] sdb: [ 2578.969570] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.969578] sd 6:0:0:0: [sdb] Attached SCSI removable disk there is nothing after 'sdb:' ... at the meantime, the lsusb shows: $ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 03f0:3207 Hewlett-Packard Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:0737 Microsoft Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub so... can anyone help me? what's wrong with my USB disk? THX

  Read the article

• What should the memory configuration be?

  - by AngryHacker

  We have a server (ProLiant DL585 G1 by HP), which hosts Windows 2003 x64 R2 with SQL Server 2005 x64 and a host of other apps. It currently has 6GB of RAM. We are currently very memory constrained and it's clear that we need to get more memory. 8GB will probably do the trick, however, we are not sure as to what memory configuration will give us the biggest performance buck. Currently all 8 memory slots are filled (4 slots have 1GB chip, while the other 4 slots have 512MB chips). Should we throw the 512MB sticks away and just replace them all with 1GB sticks? If we decided to go with a higher memory configuration (e.g. 10GB or 12GB or 16GB), is it advisable to keep all the sticks of the same size or it does not matter? I was once told that interleaved memory requires (for better performance) that memory should be in multiples (e.g. 2 or 4 or 8 or 16, etc...). I am not even sure that the server has an interleaved configuration (and don't know how to find out), but is this true? Thanks.

  Read the article

• What could be wrong with my VLAN?

  - by Matt

  I've got a VLAN 10 setup as a management VLAN. The management VLAN comes off port 48 and links to another set of switches that do not support VLAN's so it was I believe set up as an untagged access port. In the past this was a different brand of switch and this worked fine. However, since changing to the HP V1910-48G series I can't seem to get this working. I must point out that as far as I'm aware it is wired up properly (I can't check this physically as I'm working remote and have asked the tech who's got access to double check for me). Now I don't have a huge amount of experience with VLAN environments but AFAIK this is right. I've set the port 48 (linked to the management switches) as an untagged port with PVID 10 and access link type. Is this all I'd need to do from a configuration perspective to ensure all devices connected to port 48 would end up being on VLAN 10 and not needing to tag their frames. i.e. the tag would be added by the switch before being forwarded.

  Read the article

• How can laptop keyboard keys be removed and replaced?

  - by Lord Torgamus

  I'm trying to fix a laptop keyboard that has issues with keys on its left side. Just by feel, it's clear that something sticky got under there. There could be something crunchy too, but that might just be the sound of the key's spring releasing itself from the sticky. I don't know the cause because it's not my computer and the owner isn't sure, but I'm guessing soda spill for now. The computer is an HP dv2500. I've removed the keyboard and blown under it but that hasn't helped. I didn't use compressed air because I just don't have any available, but I suspect it wouldn't help with sticky. So, I'd like to pop they keys off and clean with damp cotton swabs or similar. Is there a proper way to remove the keys? I've found some instructions via Google for non-laptop keyboards, but they don't seem like they'd work for me. Alternate solutions to the problem also welcome, but I've been curious about how to remove the keys for some time for other reasons.

  Read the article

• How can I measure actual memory usage from my running processes?

  - by NullUser

  I have two servers, server1 and server2. Both of them are identical HP blades, running the exact same OS (RHEL 5.5). Here's the output of free for both of them: ### server1: total used free shared buffers cached Mem: 8017848 2746596 5271252 0 212772 1768800 -/+ buffers/cache: 765024 7252824 Swap: 14188536 0 14188536 ### server2: total used free shared buffers cached Mem: 8017848 4494836 3523012 0 212724 3136568 -/+ buffers/cache: 1145544 6872304 Swap: 14188536 0 14188536 If I understand correctly, server2 is using significantly more memory for disk I/O caching, which still counts as memory used. But both are running the same OS and if I remember correctly, I configured both with the same parameters when they were installed. I did a diff on /etc/sysctl.conf and they are identical. The problem is, I am collecting memory usage and other metrics over a period of time, (eg: vmstat, iostat, etc.) while a load is generated on the system. The memory used for caching is throwing off my calculations on the results. How can I measure actual memory usage from my running processes, rather than system usage? Is used - (buffers + cached) a valid way to measure this?

  Read the article

• W7-pro indexing mydoc on disk partition does not work

  - by Yvan Thery

  I am working on a HP-7100 mini tower running W7 Pro 64bits. My Local HD includes C:/ + 2 disk partitions : all my documents are located on disk partition L:/ and all my media files are on disk partition M:/ The indexing process works well on C:/ and M:/ but does not index the L:/ any more also all of them are allowed to be indexed, also the system is present on all drive security tabs. I have tested to rebuilt the indexing file with a new setting including few directories present on drive C/M/L but still with L: does not work ! One more thing I can tell you is that even after rebuilding the indexing file, I can find some residual directories or files which are out of the test selection. It is like unerased components remaining in the indexing database. As I do not know precisely how the indexing process works it is hard to know what to do ... Recently I had a bad time after using a past restoration procedure ... maybe it did corrupt the indexing file ???? If I start indexing the all L:/ disk partition the system stop at 39 found index also many more are existing .... Does any one from you guys could advise the process to create a new indexing database ... ? Any idea to get out of this mess ? Many thanks for assistance Yvan

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

• I can't connect to internet via lan cable because 2032 battery died and my bios bios info is now empty [closed]

  - by Rand Om Guy

  I have a compaq CQ61-112SL from about 5 years now... the main battery is almost dead, doesn't keep more then 10 minutes. anyway my problem is that my motherboard battery didn't have any more energy left a few days ago and since then I can't access internet through lan cable but only via wifi. I need cable though. I saw that on my BIOS setup page there were a bunch of parameters missing like serial number, UUID, product number and stuff like that. Also when I start the notebook it prints something like : No serial found. or something like that. I don't really know if the reason why my lan cable doesn't work is the empty BIOS but i assume that's it. If it's not please enlighten me. Or anyway tell me how to update the serial number and product number to the real ones (instead of the 0000000000000 that is now in my bios). I downloaded HP DMI which should make it possible to set these variables on the BIOS but i'm on Windows 8 64bit and the executable file that I need to open for my laptop model says it can't run on 64 bit.

  Read the article

• Windows 8 preinstall downgrade to Win 7: UEFI problems :/

  - by Tim Flemming

  I have a friend who has a Hp Laptop with UEFI booting. He locked himself out of windows 8 (forgot his password)... so he called me. Well after trying to use the latest version of chntpw in UBCD5.2.6, i came to the conclusion i needed to wipe the drive and install windows 7. A little googling suggested using certain versions of chntpw, but i decided to not waste the time burning endless CDs. Anyway, He agreed to installing Win7 "I hate the big tile thingys". So i attacked with Gparted. Wiped the whole drive. Set flags to boot. Set part table as MBR. However upon trying to install win7, it still claimed i had a GPT style disk. unable to install. the only thing i can think of I'm doing wrong is not changing the bios/UEFI to legacy... My question is, If I enable legacy, somehow get the drive to actually be MBR, and use my X86 DVD, should I be good? Is there some common glitches ppl miss when dealing with GPT/EFI/UEFI? I need answers cuz he now has a blank laptop which I am responsible for. Another question. windows 8 came installed on a GPT disk. SO WHY WHEN I BOOT THE INSTALL DVD DOES IT SAY IT CANT INSTALL TO A GPT STYLE DISK??? WTF??? talk about the bleeding edge man.

  Read the article

• Partition problem tyring to install window 7 starter

  - by ant2009

  Hello HP Mini 210 I am trying to install windows starter 7. Currently I have installed fedora 14 xfce. And I have allocated 24 GB NTFS for hard disk for the windows partition. My current partitions are as follows: /dev/sda2 97G 4.9G 91G 6% / tmpfs 494M 92K 494M 1% /dev/shm /dev/sda1 485M 68M 392M 15% /boot /dev/sda5 169G 26G 135G 16% /home I have created a boot USD to install windows starter 7. When the computer boots into the windows setup and I selected the partition I want to install windows on. I get the following message: "Setup was unable to create a new system partition or locate an existing system partition." This is setup displaying all my partitions: Disk 0 Partition 1 500MB 0 Primary Disk 0 Partition 2 97.7GB 0 Primary Disk 0 Partition 3 4GB 0 Primary Disk 0 Partition 4 171.3GB 0 Logical Disk 0 Partition 5 24.6GB 24.5 Logical <-- Trying install on this partition NTFS I have also tried to delete the partition in setup and create a new one. And also tried to format the partition. However, I still get the same error message. Many thanks for any advice,

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >