Search Results

Search found 30912 results on 1237 pages for 'load path'.

Page 93/1237 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100 | Next Page >

Cannot load from raid with grub

- by Andrew Answer

I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

Read the article
Need a recommendation for shared storage on auto-scaling ec2 w/ scalr

- by john h.

I have come across so many answers to this question that I am completely lost! I am moving our 2 sites to a load balanced ec2 system with scalr as our cloud manager. Now the question is coming up about persistent storage for the user's uploaded content and other files. Could someone please give me a suggestion and possible a link to a tutorial for the following setup and goals. 2 websites (1 Forum, 1 ecommerce). 1 LB 1 App server (to scale out to as many as needed) 1 DB server (to scale out to as many as needed) Our sites will need to autoscale and according to what I am learning about scalr, that means as new instances load up, I need to run a script to set the basics up on that server (git,php mods, pull site from git, move keys, etc) What I don't understand is how should I handle user uploaded content like profile pictures, avatars, product images, themes, etc... Do I mount an EBS or s3fs folder to hold the websites (maybe /var/www/websitefolder) or do I do something like mount the avatar folders /var/www/websitefolder/images/avatars) I am not sure where to go with this. Could someone give me some detailed help? -John

Read the article
SSH tunnel for socks5 proxy is slow with concurrent load

- by RawwrBag

I ssh to a remote AWS server using Ubuntu. I use ssh's port forwarding capabilities to do this. I have tried forwarding a dynamic port (ssh -D) or a single port (ssh -L with dante running as a remote socks server). Both are equally slow. I also tried different ciphers (ssh -c). Concurrent TCP connections pretty much do not work. For example, I can go to speedtest.net and start a test (which is fairly fast, probably maxes out my line speed) and if I try and do anything (i.e. load google.com) while the test is still running, all the additional connections seem to hang until the speed test is over. I realize OpenSSH is single-threaded. Is this the problem? It doesn't even show up on my top. Same goes for sshd on the remote server -- no processor hit. Is there anyway to bump ssh performance or should I step up to OpenVPN or something better suited for this?

Read the article
Firefox takes a really long time to load some sites on Ubuntu

- by Dave

Hello guys, I have an issue here. Some sites - just a few - takes a really long time to load on Firefox. One example is A List Apart (http://www.alistapart.com/) which takes more than 30 minutes (yes, minutes, not seconds). On Opera, ou even through a telnet session, the problematic sites run without problem, fast as expected. I am using Linux 8.04, running Firefox 3.6.3 downloaded from mozilla site, with a 10M ADSL connection. I tried many tweaks I found googling, like disable IPv6, and change http pipelining settings on FF's about:config. None worked. I also used Firebug to find what phase during negotiation is the bottleneck. Findings are in the screenshot. Well guys, any idea what is the issue? And how to solve it? I repeat, this only happens with firefox (3.6.3 and prior versions), for a few sites only (even sites with much more requests, images, javascripts, stylesheets work fine), and http pipelines and IPv6 tweaks on about:config didn't work. Thanks

Read the article
Syntax error on line 494 of httpd.conf: Cannot load .../php5apache2_2.dll into server

- by pikachu

I have been learning PHP. I had installed Apache-server (not in a combination-suite like USBWebserver). Now I'm trying to put my sites on a portable stick, using USBWebserver. I already used that program before to carry MySQL databases with me (and Apache worked as well, cause I used the included PHPMyAdmin for managing the databases.), but now it doesn't work anymore. When I start the program, I keep having the text saying Apache is offline. I've tried to open Apache using the command line (don't know what that would do, but, it's just a try). I got an error message saying Syntax error on line 494 of C:/.../httpd.conf: Cannot load C:/.../php5apache2_2.dll into server: (The following is translated from Dutch) An initialization routine of the dynamic link library (dll-file) has failed. Line 494 says this: LoadModule php5_module "C:/Users/School/Downloads/USBWebserver v8_en/php/php5apache2_2.dll" My first Apache installation (its service) is not running. The ports are different. And I also uninstalled the service (using the httpd.exe -k uninstall command); What can be the problem? Thanks for help.

Read the article
Trying to install datastax opscenter - Failed to load application: cannot import name _parse

- by gansbrest

I'm not familiar with python, maybe someone could explain what's going on here? ec2-user@prod-opscenter-01:~ % java -version java version "1.7.0_45" Java(TM) SE Runtime Environment (build 1.7.0_45-b18) Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode) ec2-user@prod-opscenter-01:~ % python -V Python 2.6.8 ec2-user@prod-opscenter-01:~ % openssl version OpenSSL 1.0.1e-fips 11 Feb 2013 And now the error ec2-user@prod-opscenter-01:~ % sudo /etc/init.d/opscenterd start Starting Cassandra cluster manager opscenterd Starting opscenterdUnhandled Error Traceback (most recent call last): File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 652, in run runApp(config) File "/usr/lib64/python2.6/site-packages/twisted/scripts/twistd.py", line 23, in runApp _SomeApplicationRunner(config).run() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 386, in run self.application = self.createOrGetApplication() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 451, in createOrGetApplication application = getApplication(self.config, passphrase) --- <exception caught here> --- File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 462, in getApplication application = service.loadApplication(filename, style, passphrase) File "/usr/lib64/python2.6/site-packages/twisted/application/service.py", line 405, in loadApplication application = sob.loadValueFromFile(filename, 'application', passphrase) File "/usr/lib64/python2.6/site-packages/twisted/persisted/sob.py", line 210, in loadValueFromFile exec fileObj in d, d File "bin/start_opscenter.py", line 1, in <module> from opscenterd import opscenterd_tap File "/usr/lib/python2.6/site-packages/opscenterd/opscenterd_tap.py", line 37, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/OpsCenterdService.py", line 13, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/ClusterServices.py", line 22, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/WebServer.py", line 40, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/Agents.py", line 18, in <module> exceptions.ImportError: cannot import name _parse Failed to load application: cannot import name _parse Maybe there are open source alternatives to monitoring cassandra I should look at? Thanks a lot

Read the article
Windows + Django + mod_wsgi = "DLL load failed"

- by Kyle MacFarlane

For a long time I was using Python 2.5 to do all this fine but recently upgraded to 2.7 since building stuff for 2.5 is a real pain. I also updated mod_wsgi to 3.3 for Python 2.7. Everything is working fine with Apache + mod_wsgi on CentOS and also in the Django runserver on both Windows and CentOS, but not with Apache + mod_wsgi on Windows. Whenever I try to access a page in my Django app I get the following (note that Apache starts fine): ImportError at / DLL load failed: The specified module could not be found. Which is caused by things like: from Crypto.Cipher import AES Etree and others cause the exact same error and it is not limited to any specific packages. Anything with pyd files fails. Googling around suggests reinstalling Python "for all users", but the installer doesn't give you that option anymore anyway. For good measure I've tried reinstalling Python 2.7 as an administrator and also told it to register itself as the default version of Python but neither helped. I think the solution might have something to do with: The fact that I have 2.5, 2.6 and 2.7 installed on this machine and mod_wsgi might be loading the DLLs for 2.5 instead of 2.7. Something to do with WSGIPythonPath, which I usually don't need to set.

Read the article
"iostat" command different in two equal machines

- by Oz.

We have several machines on Amazon (ec2) of the type c1.xlarge with 8 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are - 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st. Mem is about 1.5GB free. Any idea what could it be, or where else can we check? iostat command on the proper machine: avg-cpu: %user %nice %system %iowait %steal %idle 8.97 0.03 4.46 0.19 0.14 86.23 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.60 0.69 55.38 587620 47254184 xvdfp2 2.64 1.10 61.04 934786 52091056 xvdfp4 0.86 0.19 41.72 163866 35601920 xvdfp1 4.37 36.59 73.89 31220810 63051504 xvdfp3 8.03 7.08 94.63 6045402 80749184 iostat command on problematic machine: avg-cpu: %user %nice %system %iowait %steal %idle 9.29 0.04 5.55 0.26 0.11 84.74 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.13 3.34 68.85 246244 5077888 xvdfp1 7.60 74.31 104.88 5480362 7734840 xvdfp3 13.22 73.67 125.00 5433386 9218600 xvdfp4 1.11 0.76 65.08 55762 4799248 xvdfp2 4.16 3.31 99.17 243818 7313264 Many thanks for the help.

Read the article
Screen occasionally flashes black when under load, sometimes does not recover

- by Oak

I've built a brand new machine, but to my horror my monitor occasionally flashes black for around a second, then returning to normal. This happens under load (watching videos / playing games) but only sometimes; e.g. it doesn't occur in "Batman: Arkham City" but does in "XCOM: Enemy Unknown". When watching videos, it also occurs when not watching them full-screen, and it sometimes even occurs when the machine isn't doing anything, just sitting at the desktop and moving the mouse around. Has anyone ran into this problem and knows of any solution? Additionally, sometimes after the black screen, it won't return to normal, instead turning completely corrupt. In these cases even quitting the application doesn't help, but physically disconnecting and reconnecting the monitor fixes the problem. This problem did not occur on my earlier machine which used the same physical monitor. Additional details: Windows Server 2012, configured as Windows 8, with latest updates installed NVIDIA GeForce GTX 660 Ti, with latest driver installed Ample amounts of CPU and RAM for playing the above games and for watching videos. I've read about similar problems elsewhere but could not find a working solution: http://www.youtube.com/watch?v=Zt00C-HXFbA&noredirect=1 http://www.sevenforums.com/hardware-devices/59126-monitor-flashing-black.html https://eu.battle.net/d3/en/forum/topic/4079098908?page=4 http://www.tomshardware.com/forum/347422-33-screen-flickering-black-nvidia-driver-update

Read the article
How can I use HAproxy with SSL and get X-Forwarded-For headers AND tell PHP that SSL is in use?

- by Josh

I have the following setup: (internet) ---> [ pfSense Box ] /-> [ Apache / PHP server ] [running HAproxy] --+--> [ Apache / PHP server ] +--> [ Apache / PHP server ] \-> [ Apache / PHP server ] For HTTP requests this works great, requests are distributed to my Apache servers just fine. For SSL requests, I had HAproxy distributing the requests using TCP load balancing, and it worked however since HAproxy didn't act as a proxy, it didn't add the X-Forwarded-For HTTP header, and the Apache / PHP servers didn't know the client's real IP address. So, I added stunnel in front of HAproxy, reading that stunnel could add the X-Forwarded-For HTTP header. However, the package which I could install into pfSense does not add this header... also, this apparently kills my ability to use KeepAlive requests, which I would really like to keep. But the biggest issue which killed that idea was that stunnel converted the HTTPS requests into plain HTTP requests, so PHP didn't know that SSL was enabled and tried to redirect to the SSL site. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to both know the client's IP address and know that SSL is in use? And if possible, how can I do it on my pfSense server? Or should I drop all this and just use nginx?

Read the article
Chrome will not load a web page with an <embed> element

- by rossmcm

I have been trying to get a simple sound web page going: Sound.html <script> function PlaySound () { var sounder = document.getElementById ("ToneA") ; sounder.Play () ; } </script> <embed id="ToneA" height="1" width="1" src="https://dl.dropboxusercontent.com/u/311035/ToneA.mp3" autostart="false" enablejavascript="true"//> <button onclick="PlaySound () ;">Play</button> The test web page is here. It plays in IE, but not in Firefox or Chrome. My problem: Chrome reports "Could not load VLC Plugin". It seems to be a known problem that the VLC community don't necessarily feel like fixing at the moment, and is a result of Google choosing not to allow some certain kind of plugin. If I disable the plugin I no longer get the message but nothing happens when I click the button. Looking at the console in a debug window I see Uncaught TypeError: undefined is not a function Sound.html:7 PlaySound Sound.html:7 onclick which suggests Chrome could not find anything else to handle the sound file. How to I tell Chrome to use (e.g.) Windows Media Player? * UPDATE * This is apparently because the VLC plugin is a NPAPI plugin and Chrome no longer supports these. I have uninstalled VLC and this has removed the error on loading the webpage with an embedded sound element, but it still doesn't invoke WMP instead.

Read the article
Linux 2.6.24-gentoo-r3-comtrance on x86_64 high Useage for unknown reasons

- by Dorjan

Hello everyone, I'm a complete rookie when it comes to all things Linux related so please treat me as such and assume I know nothing. That being said my Top says this: top - 12:08:03 up 11 days, 15:36, 0 users, load average: 5.47, 5.53, 5.46 Tasks: 296 total, 2 running, 294 sleeping, 0 stopped, 0 zombie Cpu(s): 6.3%us, 1.4%sy, 0.0%ni, 71.3%id, 20.6%wa, 0.0%hi, 0.3%si, 0.0%st Mem: 8176880k total, 8118236k used, 58644k free, 89312k buffers Swap: 1004052k total, 0k used, 1004052k free, 7235652k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1229 root 15 -5 0 0 0 D 1 0.0 199:28.63 kjournald 2946 root 20 0 1716 676 552 D 1 0.0 145:02.94 syslogd 14553 root 20 0 2644 1268 876 R 1 0.0 0:00.34 top 14609 postfix 20 0 7896 1884 1460 D 1 0.0 0:00.02 bounce 14630 postfix 20 0 7896 1876 1452 R 0 0.0 0:00.00 bounce And my hard drives says: > df -k Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda3 4925556 4474836 200508 96% / /dev/sda5 489992 36090 428602 8% /tmp /dev/sda6 377951852 236171160 122581816 66% /var none 4088440 0 4088440 0% /dev/shm It has been like it for a few days now... I know not what is causing the high server load (Normally around 1.3) can anyone give any tips on how to track down the culprit? Many thanks,

Read the article
Difference between all servers in one cluster and more than one cluster with servers?

- by silla

Not sure I understand what´s the difference or how it works when servers a running in one cluster or if there are more than one clusters with servers in it - regard High availability & Load Balancing. For me they are somehow the same, there is not really a big difference. Let´s make a simple example: 2 Servers in 1 Cluster 2 Clusters with each 1 Server - 1. If one Server failure, the other one is able to continue the work. The same for Load Balancing, these two Servers are able to balance the work together. - 2. The same thing! If one Server failure... The only thing that could be a problem with point 1. is if the Cluster fails (then both of the Server are dead). But is this even possible? I was reading stuff about clustering and high availability but I think I do not get this really. Probably I did not really understand how a cluster is working. Are these 2 points with 1 Cluster and 2 Clusters somehow the same or are there really some big differences? What should I know about it? Thank you

Read the article
Zero downtime deployment (Tomcat), Nginx or HAProxy, behind hardware LB - how to "starve" old server?

- by alexeypro

Currently we have the following setup. Hardware Load Balancer (LB) Box A running Tomcat on 8080 (TA) Box B running Tomcat on 8080 (TB) TA and TB are running behind LB. For now it's pretty complicated and manual job to take Box A or Box B out of LB to do the zero downtime deployment. I am thinking to do something like this: Hardware Load Balancer (LB) Box A running Nginx on 8080 (NA) Box A running Tomcat on 8081 (TA1) Box A running Tomcat on 8082 (TA2) Box B running Nginx on 8080 (NB) Box B running Tomcat on 8081 (TB1) Box B running Tomcat on 8082 (TB2) Basically LB will be directing traffic between NA and NB now. On each of Nginx's we'll have TA1, TA2 and TB1, TB2 configured as upstream servers. Once one of the upstreams's healthcheck page is unresponsive (shutdown) the traffic goes to another one (HttpHealthcheckModule module on Nginx). So the deploy process is simple. Say, TA1 is active with version 0.1 of the app. Healthcheck on TA1 is OK. We start TA2 with Healthcheck on it as ERROR. So Nginx is not talking to it. We deploy app version 0.2 to TA2. Make sure it works. Now, we switch the Healthcheck on TA2 to OK, switch Healthcheck to TA1 to ERROR. Nginx will start serving TA2, and will remove TA1 out of rotation. Done! And now same with the other box. While it sounds all cool and nice, how do we "starve" the Nginx? Say we have pending connections, some users on TA1. If we just turn it off, sessions will break (we have cookie-based sessions). Not good. Any way to starve traffic to one of the upstream servers with Nginx? Thanks!

Read the article
Redirect without changing URL

- by Coobadivin

Here's the setup. We have a hardware load balancer with an http virtual cluster. Let's call this virtual cluster example1.com. This virtual cluster load balances between two squid reverse proxies which are also on the same physical servers as the web servers. Squid listens on 80 and points to itself as the cache_peer web server which listens on 81. We also have a standalone web server which we will call example2.com. What we are trying to do is create a subdirectory on example1.com called example1.com/example2. This will point to example2.com, but we want our users to stay at example1.com/example2 in their browser. So, it's like a redirect without actually being a redirect. How the hell do I go about doing this? Is this even possible? I'm looking at squid docs in the meantime. example1.com is running a proprietary web server - not Apache :( We can't host example2.com's content in example1.com's file system. These are two very different platforms.

Read the article
3 Server, is this a cluster scenario?

- by HornedBeast

Hello, At the moment I have one Ubuntu server, 9.10, running with a simple Samba share, a mail server, DNS server and DHCP server. Mostly its just there for file sharing and email server. I also have 2 other servers that are exactly the same hardware and spec as the first, which have an rsync set up to retrieve the shared folders and backs them up. However, if the first server goes down, all of our shares disappear along with our mail and the system must be rebuilt. Also I tend to find if people are downloading a large amount from the file server, no-one can access there emails - especially in the morning when everyone is signing in at once. Would it be more beneficial for me to have all 3 servers, all running the same services, doing the same thing with some sort of cluster with load balancing? In short, how can I get the best out of my 3 hardware servers? I'm not really sure where to begin looking, or how to go about such a setup where 3 servers are all identical, but perhaps one acts as the main load balancer?? If someone can point me in the right direction, or if this simply sounds like one of those Enterprise Cloud's that is now a default setup in Ubuntu Server 9.10+, then I'll go down that route. Cheers in advance. Andy

Read the article
not able to write log file to specified path(Microsoft Enterprise Library Logging)

- by prince23

hi, i am trying to implement the logging Configuration using Microsoft Enterprise Library Logging class Program { static void Main(string[] args) { LogEntry entry = new LogEntry() { Message = "Hello Ent. Lib. Logging" }; Logger.Write(entry); } } here the entry conyain she details. but these details are not written in the file i web config i have the settings done like this. <?xml version="1.0" encoding="utf-8"?> <configuration> <configSections> <section name="loggingConfiguration" type="Microsoft.Practices.EnterpriseLibrary.Logging.Configuration.LoggingSettings, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <section name="exceptionHandling" type="Microsoft.Practices.EnterpriseLibrary.ExceptionHandling.Configuration.ExceptionHandlingSettings, Microsoft.Practices.EnterpriseLibrary.ExceptionHandling, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> <section name="dataConfiguration" type="Microsoft.Practices.EnterpriseLibrary.Data.Configuration.DatabaseSettings, Microsoft.Practices.EnterpriseLibrary.Data, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" /> </configSections> <loggingConfiguration name="Logging Application Block" tracingEnabled="true" defaultCategory="General" logWarningsWhenNoCategoriesMatch="true"> <listeners> <add fileName="C:\Inetpub\wwwroot\trace.log" header="----------------------------------------" footer="----------------------------------------" formatter="" listenerDataType="Microsoft.Practices.EnterpriseLibrary.Logging.Configuration.FlatFileTraceListenerData, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" traceOutputOptions="None" filter="All" type="Microsoft.Practices.EnterpriseLibrary.Logging.TraceListeners.FlatFileTraceListener, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" name="FlatFile TraceListener" /> <add source="Enterprise Library Logging" formatter="Text Formatter" log="Application" machineName="" listenerDataType="Microsoft.Practices.EnterpriseLibrary.Logging.Configuration.FormattedEventLogTraceListenerData, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" traceOutputOptions="None" filter="All" type="Microsoft.Practices.EnterpriseLibrary.Logging.TraceListeners.FormattedEventLogTraceListener, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" name="Formatted EventLog TraceListener" /> </listeners> <formatters> <add template="Timestamp: {timestamp}
Message: {message}
Category: {category}
Priority: {priority}
EventId: {eventid}
Severity: {severity}
Title:{title}
Machine: {machine}
Application Domain: {appDomain}
Process Id: {processId}
Process Name: {processName}
Win32 Thread Id: {win32ThreadId}
Thread Name: {threadName}
Extended Properties: {dictionary({key} - {value}
)}" type="Microsoft.Practices.EnterpriseLibrary.Logging.Formatters.TextFormatter, Microsoft.Practices.EnterpriseLibrary.Logging, Version=4.1.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" name="Text Formatter" /> </formatters> <categorySources> <add switchValue="All" name="General"> <listeners> <add name="Formatted EventLog TraceListener" /> </listeners> </add> </categorySources> <specialSources> <allEvents switchValue="All" name="All Events" /> <notProcessed switchValue="All" name="Unprocessed Category" /> <errors switchValue="All" name="Logging Errors & Warnings"> <listeners> <add name="Formatted EventLog TraceListener" /> </listeners> </errors> </specialSources> </loggingConfiguration> <exceptionHandling> <exceptionPolicies> <add name="Exception Policy"> <exceptionTypes> <add type="System.Exception, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089" postHandlingAction="NotifyRethrow" name="Exception" /> </exceptionTypes> </add> </exceptionPolicies> </exceptionHandling> </configuration> i am trying by best to solve this from past 2 days. if any one knw what is the issue here. why my log file is not written in the specified path. and even the details of log are not written in the file path fileName="C:\Inetpub\wwwroot\trace.log"

Read the article
Problem with script substitution when running script

- by tucaz

Hi! I'm new to Linux so this probably should be an easy fix, but I cannot see it. I have a script downloaded from official sources that is used to install additional tools for fsharp but it gives me a syntax error when running it. I tried to replace ( and ) by { and } but eventually it lead me to another error so I think this is not the problem since the script works for everybody. I read some articles that say that my bash version maybe is not the right one. I'm using Ubuntu 10.10 and here is the error: install-bonus.sh: 28: Syntax error: "(" unexpected (expecting "}") And this is line 27, 28 and 29: { declare -a DIRS=("${!3}") FILE=$2 And the full script: #! /bin/sh -e PREFIX=/usr BIN=$PREFIX/bin MAN=$PREFIX/share/man/man1/ die() { echo "$1" &2 echo "Installation aborted." &2 exit 1 } echo "This script will install additional material for F# including" echo "man pages, fsharpc and fsharpi scripts and Gtk# support for F#" echo "Interactive (root access needed)" echo "" # ------------------------------------------------------------------------------ # Utility function that searches specified directories for a specified file # and if the file is not found, it asks user to provide a directory RESULT="" searchpaths() { declare -a DIRS=("${!3}") FILE=$2 DIR=${DIRS[0]} for TRYDIR in ${DIRS[@]} do if [ -f $TRYDIR/$FILE ] then DIR=$TRYDIR fi done while [ ! -f $DIR/$FILE ] do echo "File '$FILE' was not found in any of ${DIRS[@]}. Please enter $1 installation directory:" read DIR done RESULT=$DIR } # ------------------------------------------------------------------------------ # Locate F# installation directory - this is needed, because we want to # add environment variable with it, generate 'fsharpc' and 'fsharpi' and also # copy load-gtk.fsx to that directory # ------------------------------------------------------------------------------ PATHS=( $1 /usr/lib/fsharp /usr/lib/shared/fsharp ) searchpaths "F# installation" FSharp.Core.dll PATHS[@] FSHARPDIR=$RESULT echo "Successfully found F# installation directory." # ------------------------------------------------------------------------------ # Check that we have everything we need # ------------------------------------------------------------------------------ [ $(id -u) -eq 0 ] || die "Please run the script as root." which mono /dev/null || die "mono not found in PATH." # ------------------------------------------------------------------------------ # Make sure that all additional assemblies are in GAC # ------------------------------------------------------------------------------ echo "Installing additional F# assemblies to the GAC" gacutil -i $FSHARPDIR/FSharp.Build.dll gacutil -i $FSHARPDIR/FSharp.Compiler.dll gacutil -i $FSHARPDIR/FSharp.Compiler.Interactive.Settings.dll gacutil -i $FSHARPDIR/FSharp.Compiler.Server.Shared.dll # ------------------------------------------------------------------------------ # Install additional files # ------------------------------------------------------------------------------ # Install man pages echo "Installing additional F# commands, scripts and man pages" mkdir -p $MAN cp *.1 $MAN # Export the FSHARP_COMPILER_BIN environment variable if [[ ! "$OSTYPE" =~ "darwin" ]]; then echo "export FSHARP_COMPILER_BIN=$FSHARPDIR" fsharp.sh mv fsharp.sh /etc/profile.d/ fi # Generate 'load-gtk.fsx' script for F# Interactive (ask user if we cannot find binaries) PATHS=( /usr/lib/mono/gtk-sharp-2.0 /usr/lib/cli/gtk-sharp-2.0 /Library/Frameworks/Mono.framework/Versions/2.8/lib/mono/gtk-sharp-2.0 ) searchpaths "Gtk#" gtk-sharp.dll PATHS[@] GTKDIR=$RESULT echo "Successfully found Gtk# root directory." PATHS=( /usr/lib/mono/gtk-sharp-2.0 /usr/lib/cli/glib-sharp-2.0 /Library/Frameworks/Mono.framework/Versions/2.8/lib/mono/gtk-sharp-2.0 ) searchpaths "Glib" glib-sharp.dll PATHS[@] GLIBDIR=$RESULT echo "Successfully found Glib# root directory." PATHS=( /usr/lib/mono/gtk-sharp-2.0 /usr/lib/cli/atk-sharp-2.0 /Library/Frameworks/Mono.framework/Versions/2.8/lib/mono/gtk-sharp-2.0 ) searchpaths "Atk#" atk-sharp.dll PATHS[@] ATKDIR=$RESULT echo "Successfully found Atk# root directory." PATHS=( /usr/lib/mono/gtk-sharp-2.0 /usr/lib/cli/gdk-sharp-2.0 /Library/Frameworks/Mono.framework/Versions/2.8/lib/mono/gtk-sharp-2.0 ) searchpaths "Gdk#" gdk-sharp.dll PATHS[@] GDKDIR=$RESULT echo "Successfully found Gdk# root directory." cp bonus/load-gtk.fsx load-gtk1.fsx sed "s,INSERTGTKPATH,$GTKDIR,g" load-gtk1.fsx load-gtk2.fsx sed "s,INSERTGDKPATH,$GDKDIR,g" load-gtk2.fsx load-gtk3.fsx sed "s,INSERTATKPATH,$ATKDIR,g" load-gtk3.fsx load-gtk4.fsx sed "s,INSERTGLIBPATH,$GLIBDIR,g" load-gtk4.fsx load-gtk.fsx rm load-gtk1.fsx rm load-gtk2.fsx rm load-gtk3.fsx rm load-gtk4.fsx mv load-gtk.fsx $FSHARPDIR/load-gtk.fsx # Generate 'fsharpc' and 'fsharpi' scripts (using the F# path) # 'fsharpi' automatically searches F# root directory (e.g. load-gtk) echo "#!/bin/sh" fsharpc echo "exec mono $FSHARPDIR/fsc.exe --resident \"\$@\"" fsharpc chmod 755 fsharpc echo "#!/bin/sh" fsharpi echo "exec mono $FSHARPDIR/fsi.exe -I:\"$FSHARPDIR\" \"\$@\"" fsharpi chmod 755 fsharpi mv fsharpc $BIN/fsharpc mv fsharpi $BIN/fsharpi Thanks a lot!

Read the article
What exactly is the 'Anonymously Hosted DynamicMethods Assembly' and how can I make it load manually

- by dbaw

As a .NET developer, the line '<process>' (Managed): Loaded 'Anonymously Hosted DynamicMethods Assembly' probably is familiar to you. My question is simple and straightforward: what exactly is this 'Anonymously Hosted DynamicMethods Assembly' and can I make it (pre)load manually? If so, how? Can this be done via Assembly.Load(...)?

Read the article
Could not load file or assembly 'System.Web.Ajax, Version=3.0.31106.0

- by Jonesy

HI folks, I have a .net application (vb.net) and I'm using the ajax control toolkit. It works fine on my production machine but when I upload it to the host (fasthosts) i get this error: Could not load file or assembly 'System.Web.Ajax, Version=3.0.31106.0, Culture=neutral, PublicKeyToken=28f01b0e84b6d53e' or one of its dependencies. The module was expected to contain an assembly manifest. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.BadImageFormatException: Could not load file or assembly 'System.Web.Ajax, Version=3.0.31106.0, Culture=neutral, PublicKeyToken=28f01b0e84b6d53e' or one of its dependencies. The module was expected to contain an assembly manifest. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Assembly Load Trace: The following information can be helpful to determine why the assembly 'System.Web.Ajax, Version=3.0.31106.0, Culture=neutral, PublicKeyToken=28f01b0e84b6d53e' could not be loaded. WRN: Assembly binding logging is turned OFF. To enable assembly bind failure logging, set the registry value [HKLM\Software\Microsoft\Fusion!EnableLog] (DWORD) to 1. Note: There is some performance penalty associated with assembly bind failure logging. To turn this feature off, remove the registry value [HKLM\Software\Microsoft\Fusion!EnableLog]. Stack Trace: [BadImageFormatException: Could not load file or assembly 'System.Web.Ajax, Version=3.0.31106.0, Culture=neutral, PublicKeyToken=28f01b0e84b6d53e' or one of its dependencies. The module was expected to contain an assembly manifest.] AjaxControlToolkit.ToolkitScriptManager.ApplyAssembly(ScriptReference script, Boolean isComposite) +0 AjaxControlToolkit.ToolkitScriptManager.OnResolveScriptReference(ScriptReferenceEventArgs e) +167 System.Web.UI.ScriptManager.RegisterScripts() +191 System.Web.UI.ScriptManager.OnPagePreRenderComplete(Object sender, EventArgs e) +113 System.Web.UI.Page.OnPreRenderComplete(EventArgs e) +8698462 System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +1029 Here is my web.conf file. Its very simple: <system.web> <customErrors mode="Off"/> <compilation debug="true"> <assemblies> <add assembly="System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> <add assembly="System.Web.Extensions.Design, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> <add assembly="System.Design, Version=2.0.0.0, Culture=neutral, PublicKeyToken=B03F5F7F11D50A3A"/> <add assembly="System.Windows.Forms, Version=2.0.0.0, Culture=neutral, PublicKeyToken=B77A5C561934E089"/></assemblies></compilation></system.web> Does anyone know whats up? -- Billy

Read the article
WebView load css from local file

- by ADAM

[[self mainFrame] loadHTMLString:@"<html><body><link href='main.css' rel='stylesheet' type='text/css' /></body></html>" baseURL:nil]; I am trying to load a css file called main.css from the application Resources folder as below from a WebView, how do i get the path of the resources folder correct so i can load the css?

Read the article
Could not load Assembly 'Microsoft.Office.Server.Search'

- by Hitesh Wadekar

Hi I have got following error: "Could not load file or assembly 'Microsoft.Office.Server.Search, Version=12.0.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c' or one of its dependencies. An attempt was made to load a program with an incorrect format." Does anybody know solution for this? or Does anybody gonn through this error? Any input greatly appretiated?

Read the article
Load image in device independent and screen independent fashion into a layout view using 1.6 SDK

- by Mark Wigzell

I'm having trouble getting an asset image to scale up when I load it. The new call to BitmapDrawable(Resources, BitmapDrawable) is not available on 1.6 SDK. Is there a workaround to load the BitmapDrawable the old way and then somehow manipulate it? I have tried calling setTargetDensity() to no avail. My code (which doesn't scale properly) is: ImageView iv = (ImageView)view.findViewById(R.id.image); iv.setImageDrawable(new BitmapDrawable(view.getContext().getAssets().open(path)));

Read the article
Delphi Imagelist: Load icons with ResourceLoad from a .res

- by ben

Hi guys, I', trying to load an icon from a res file into an image list. I created the res file with the delphi ImageEditor. And this way I'm trying to load the icon: //if ImageList1.ResourceLoad(rtIcon, 'TEXT_BOLD', clWhite) then if imagelist1.GetResource(rtIcon, 'TEXT_BOLD', 0, [lrDefaultColor], clRed) then showmessage('loaded') else showmessage('not loaded'); Both ways doesn't work. Any ideas? Thanks!

Read the article
Load a png resource into a CBitMap

- by Rohit Sasikumar

How do i load a png resource into a CBitMap? When i try this it doesnt work. CImage image; image.LoadFromResource(AfxGetInstanceHandle(), IDB_PNG1); bitmap.Attach(image.Detach()); It gives me an error resource type not found. Is there any other way to load a PNG resource?

Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100 | Next Page >