Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 94/370 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• Check packet vlan tag using Tap virtual interface

  - by ankit

  Hi all, I am trying to learn how to implement virtual interfaces using the Tap driver. So far my understanding is that using the tap driver I can create a virtual interface and then have a userspace program attach to this interface to analyse the data coming into this device. Now what if I attach a cisco switch to my LAN interface using a TRUNK link, forward all the packets coming into the LAN interface to the virtual tap interface and then in my program attached to this interface do some coding to analyze the vlan tag in the packet and only allow certain vlans to be forwarded to the WAN interface ? Does this sound plausible or is there is flaw in my basic understanding ? Thanks for the help! ankit

  Read the article

• Configuring VLAN's on two HP procurve switches

  - by pan

  Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this ISP is coming through my internal network, I plan on using a new vlan called "airspeed" only for this ISP traffic. Up until now I've just been using the Default_vlan on both HP switches (4108 + 2524). So far I've been unable to ping from my laptop to the ISP modem both of which are on the new vlan 2 ("Airspeed"). No traffic needs to cross from vlan 2 to vlan 1 so I've left the ports as untagged. I've used the subnet provide from my ISP as the new vlan 2 subnet. Can anybody see what I'm doing wrong here? I've added the configuration of both switch below. Rough diagram: Microwave modem (Gateway IP 77.75.00.49) | HP 2524 switch (port 24) | HP 2524 switch fibre link | HP 4108GL switch fibre link | HP 4108GL switch (port D1) | Laptop configured with IP 77.75.00.50 (for testing but will be connected to firewall) And my 4108GL config: ; J4865A Configuration Editor; Created on release #G.07.21 hostname "HP ProCurve Switch 4108GL" cdp run module 1 type J4864A module 2 type J4862B module 3 type J4862B module 4 type J4862B ip default-gateway 128.1.146.50 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged A1-A3,B1-B24,C1-C24,D2-D24 ip address 128.1.146.203 255.255.0.0 no untagged D1 exit vlan 2 name "Airspeed" untagged D1 ip address 77.75.00.51 255.255.255.248 exit Finally my 2524 config: ; J4813A Configuration Editor; Created on release #F.04.08 hostname "HP ProCurve Switch 2524" cdp run ip default-gateway 0.0.0.0 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.51 "public" snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged 1-23,25-26 no untagged 24 ip address 128.1.146.204 255.255.0.0 exit vlan 2 name "Airspeed" untagged 24 ip address 77.75.00.51 255.255.255.248 exit no aaa port-access authenticator active

  Read the article

• SQL instance through F5 BigIP VIP

  - by Sam

  We have a SQL 2008 instance Server01\instance02. The port is set to 1466. We've set up a VIP named Server1 Attempting to connect to Server1\instance02 does not work. Server1,1466 does work. We have ports 1433, 1434 and 1466 open. Can we configure this to be able to use the name without any changes to the SQL client. Thanks!!

  Read the article

• configuring two network interfaces in ubuntu 10.04.1

  - by Bill Smith

  I have got two NICs configured on a VM - each is tied to a specific network, one is a DMZ, the other is an internal network. I want MySQL to listen on the internal network only and Apache on the DMZ listening for HTTP and HTTPS. But as soon as I add the second interface I run into trouble. I can hit HTTP on either interface, but can not hit 3306 on the internal network for MySQL. Here's the config... could someone sanity check this please? auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.153.24.230 netmask 255.255.255.240 network 10.153.24.224 broadcast 10.153.24.239 dns-nameservers 8.8.8.8 auto eth1 iface eth1 inet static address 10.153.24.195 netmask 255.255.255.224 gateway 10.153.24.193 broadcast 10.153.23.223

  Read the article

• Windows user account just for accessing network shares on a Windows 7 machine

  - by Paulo

  I would like my Xbox (Xbmc) to access my Windows 7 shares without having Guest accounts enabled and without using my Administrator account login details. I have tried making it an account called Xbox and this works fine but the Xbox account appears on the login page for Windows. Is there a way to create an account that is purely for accessing shares without it appearing as a user account????

  Read the article

• connect two ESX hosts on private LAN

  - by maruti

  can a PC setup as W2K3 DC manage two ESX hosts connected to physical hub/switch? Services: DNS, DHCP, Domain distributed to host using a hub/switch. NIC2 on each host connected to switch/hub...spanning a virtual network inside each ESX host

  Read the article

• Changing subnet-mask of class-c network host to 255.255.0.0

  - by Prashant Mandhare

  We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

  Read the article

• windows 7 no internet access

  - by Kyle

  Just did a fresh install of Windows 7, and the network and sharing center says no internet access. Disabling and enabling the adapter seems to fix the issue temporarily, but the internet stops working shortly after. I have installed the latest NIC drivers and have installed all Windows updates. I have also tried manually setting the ip/gateway/dns and running netsh int ip reset in an elevated command prompt. I am running Windows 7 Home Premium 64bit with a wired connection. I have searched for hours, but have found no working solutions. Does anyone have any ideas?

  Read the article

• Setting up Windows 2008 with VPN and NAT

  - by Benson

  I have a Windows 2008 box set up with VPN, and that works quite well. NPS is used to validate the VPN clients, who are able to access the private address of the server, once connected. I can't for the life of me get NAT working for the VPN clients, though. I've added NAT as a routing protocol, and set the one on in the VPN address pool as private, and the other as public - but it still won't NAT connections when I add a route through the VPN server's IP on the client side (route add SomeInternetIp IpOfPrivateInterfaceOnServer). I know I can reach the server's private interface (which happens to be 10.2.2.1) with remote desktop client, so I can't think of any issues with the VPN.

  Read the article

• Vista ICS issue

  - by Bill Grey

  I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

  Read the article

• How to install Archlinux on a acer emachines em350 ?

  - by zillion

  Do a 64 bits version will work better if the cpu is 64 bits capable ? Can I remove all added stuffs on Archbang or CTKArchLive to return to plain Archlinux with openbox that I can configure myself easily, so I can install Archlinux faster ? I tried and installed Arch properly but I need to install the broadcom bcm 4727 driver (b43,wl,sta,open source), which driver do I need and how can I install it by my usb on Archlinux CLI made with base, sudo and wireless_tools only ?

  Read the article

• Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

  - by Nick G

  I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

  Read the article

• Best free (or cheap) ASP.NET based CMS for a club/association?

  - by marc_s

  I've been looking for a simple, intuitive ASP.NET based CMS to handle my club/association site. It should be based on ASP.NET so I can add some extra specific pages offer a membership system, e.g. I want to be able to define members which can e.g. comment posts, while anonymous users can only read (no active participation) have features like news, forums, blogs, picture gallery be simple and easy to use I've been looking at GraffitiCMS: so far my favorite, but it has no forum, and no membership system, and no future, it seems - no development whatsoever in over a year :-( Sitefinity: had extreme trouble even getting it installed, and when it's finally up and running, I find it overly complicated and not intuitive at all Umbraco: same problem - hard to install, hard to get up and running, the intro videos on their site are only available to paying subscribers (what's up with that deal???)..... DotNetNuke: seems like a major overkill Community Server: seems like a major overkill - and seems to be more and more commercial, only Any others I've missed that I should have definitely looked at ??

  Read the article

• Permanently change IP address on SuSE 10

  - by Long Ngo

  I am trying to change IP address of a SuSE 10 machine that is running Tomcat. I need to create a shell script to do this so could not use YaST. As some sites suggested on my Google search, I edited the files in /etc/sysconfig/network/ifcfg-eth-* to change the IP address. After that, I restarted the network service by calling /etc/init.d/network restart. The network card restarting just fine. I, then, restarted tomcat web service. However, when I browsed the new IP address using browser, I got an "Request denied" message. Can anyone please tell me how I could do this? Thanks

  Read the article

• Multi-Boot through IPMI possible?

  - by yoursort

  Hi, I want to setup a cluster. On each machine Windows XP and Linux should be installed and the OS should be selectable by a boat loader (e.g. grub). All machines have IPMI cards. Is it possible when starting the machines over IPMI to also select the OS to boot? And how? Thanks!

  Read the article

• ip namespace non-root shell

  - by user2730940

  I am trying to run ssh command to another ip namespace. I can do it right now, but it runs as root. I want to run it as a normal user. I want to know if there is a way to enter a non-root shell in another network namespace. I know you can use this to enter a root shell in another namespace: sudo ip netns exec <namespace> bash Alternatively, is there a way to run single commands as a non-root user? I know you can run commands as root with this: sudo ip netns exec <namespace> <command>

  Read the article

• Unable to browse Server 2008R2 from XP clinets

  - by Dave M

  We have just deployed a Windows 2008R2 server in our Windows 2003 domain. XP clinets are unable to browse in "entire network" and find the new server. It can be accessed by entering \\servername and it can be pinged by name and IP address. Users access shares without issue. Netbios over TCP/IP is enabled. Computer browser is running on the Windows 2008R2 system. Turn on Network Discovery is enabled. These services were started as a result of an MS article Computer Browser DNS Client Function Discovery Resource Publication SSDP Discovery UPnP Device Hosts

  Read the article

• How can I set up multiple dynamic users to update a single network's dynamic IP

  - by d3vid

  On my home network we are allocated a dynamic IP. I want to configure ddclient (or an equivalent) to send IP updates to DNS-O-Matic/OpenDNS only when I am on my home network. I do not want to send IP updates when I'm on my office network. Can this be done? I am prepared to use different FLOSS software or a different free DNS service. Additionally, there are multiple users who may be on the home network or away on other networks. How can we configure ddclient on each machine so that whoever is on the home network updates the IP (i.e. so we don't have to rely on a particular machine being on the network to update the IP). OpenDNS support have said we can't simply install updater software on each machine.

  Read the article

• Automatically repair network connection when it goes down.

  - by Spines

  Every hour or so my wireless router goes down, and everyone connected loses internet for a couple minutes. If I right click on my network connection and choose repair, I usually get internet back quicker. Is there a way I can automatically have it try to repair the connection once it goes down? Can I write a program to do this if there isn't a built in windows setting? BTW I'm using Windows XP. EDIT:My router is a Linksys WRT110 with Firmware Version: 1.0.04, and I have cable internet. The signal is 100%. I live in an apartment complex and there are about 15 other wifi networks visible to me, not sure if that has any effect.

  Read the article

• Filtering SNMP View

  - by Arie K

  We have several network interfaces in a machine. How to configure SNMP view to limit which interfaces could be shown to public community? We're using Ubuntu Server and default SNMPD from the repository. We have successfully limit the SNMPD agent to show only interfaces tree using this configuration: view system included .iso.org.dod.internet.mgmt.mib-2.interfaces

  Read the article

• Cisco 837 not passing UDP traffic properly (was: DNS query problem)

  - by TessellatingHeckler

  We have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch - LAN. It has been fine for years, suddenly DNS resolution stopped working from the LAN to public DNS servers. No changes that I know of, so I can't revert anything. Current behaviour: DNS requests from the LAN using TCP show up in the oubound firewall log, in the Cisco debug log, in the dns-server-firewall, in tcpdump on the DNS server, the answer comes back, it works fine. DNS requests from the LAN using UDP show up in the outbound firewall log, in the Cisco debug log, but does NOT show in the dns-server-firewall, not in tcpdump on the DNS server, times out. DNS requests from the Cisco using UDP show up in the dns-server-firewall and in tcpdump on the DNS server, answer received, works fine. netcat connections to port 53 or a random port by TCP show up in the dns-server-firewall netcat connections to port 53 or a random port by UDP do not show up in the dns-server-firewall Summary: TCP seems fine throughought. UDP works from the Cisco over the ADSL, and it works from the LAN to the Cisco, but it doesn't seem to cross the Cisco 837 properly. Update: confirmed with netcat that any UDP traffic from the LAN is affected, not just traffic to port 53. Update: If I change the firewall's external IP to any other IP in the subnet, this starts working. When I put it back, it stops working. I now suspect it's an ISP issue (does that sound plausible?), and am removing the Cisco config.

  Read the article

• Setting up a software access point on Gigabyte GN-WPKG x64

  - by Reckage

  I'm using a Gigabyte GN-WPKG card on Windows 7 64-bit and was thinking it would be good to turn it into a wireless AP (I have a wired internet connection). Connectify, which would normally be the solution, says it's not compatible. There are instructions for setting up an AP, but they seem to be for 32-bit. I found the equivalent drivers for 7 and they don't seem to do anything. Is there no SoftAP for Vista and later on a Gigabyte card?

  Read the article

• Clickonce applications being allowed through firewall

  - by DanielF

  The company I work for uses an application that is deployed through clickonce. This means that everytime they update said program the program regenerates in a new location ie: C:\Users\%username%\AppData\Local\Apps\2.0\89XCT43D.10T\WBZ8WE7L.927\trm8..tion_1ad39bb503bcb5df_0008.0005_14829906c9aa8611\%appname%.exe Recently the computers were updated to windows 7 machines and now everytime an update is pushed out the windows firewall see this as a new application and prompts the users to allow the program through the firewall. THis means I have to walk around to every computer and type in admin credentials. Does anyone know of a way to allow the application regardless of the path it is in? Google has not been very helpful so far.

  Read the article

• PPTP Client setup, Fedora 17

  - by Suarez Romina

  I am trying to connect to hidemyass.com VPN services via PPTP, but I am having issues understanding why it isn't working, since I don't get a warning or fatal error and my IP remains the same. This is how i create the connection: [root@lasvegas-nv-datacenter ~]# pptpsetup --create TUNNELNAME --server 199.58.165.20 --username MYUSERNAME --password MYPASSWORD --encrypt --start And this is the output: Using interface ppp0 Connect: ppp0 <-- /dev/pts/1 CHAP authentication succeeded MPPE 128-bit stateless compression enabled local IP address 10.200.21.14 remote IP address 10.200.20.1 After that, I check the log and this is what i get: [root@lasvegas-nv-datacenter ~]# tail -f /var/log/messages Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 1 'Start-Control-Connection-Request' Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:754]: Received Start Control Connection Reply Aug 24 11:25:33 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:788]: Client connection established. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_rep:pptp_ctrl.c:254]: Sent control packet type is 7 'Outgoing-Call-Request' Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:873]: Received Outgoing Call Reply. Aug 24 11:25:34 lasvegas-nv-datacenter pptp[3892]: anon log[ctrlp_disp:pptp_ctrl.c:912]: Outgoing call established (call ID 0, peer's call ID 20096). Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: CHAP authentication succeeded Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: MPPE 128-bit stateless compression enabled Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: local IP address 10.200.21.14 Aug 24 11:25:38 lasvegas-nv-datacenter pppd[3884]: remote IP address 10.200.20.1 Can someone help me? Basically, i Ieed to connect to the VPN and have my IP changed after the connection. I read a lot of guides but still cannot understand why I don't get a connection.

  Read the article

• Setup Linksys 3200 remote access

  - by Greg

  I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are: When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. Any idea's on what else I have to do to allow remote management access? UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >