Search Results

Search found 7756 results on 311 pages for '64'.

Page 95/311 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Styles of games that work at low-resolution

  - by Brendan Long

  I'm taking a class on compilers, and the goal is to write a compiler for Meggy Jr devices (Arduino). The goal is just to make a simple compilers with loops and variables and stuff. Obviously, that's lame, so the "real goal" is to make an impressive game on the device. The problem is that it only has 64 pixels to work with (technically 72, but the top 8 are single-color and not part of the main display, so they're really only useful for displaying things like money). My problem is thinking of something to do on a device that small. It doesn't really matter if it's original, but it can't be something that's already available. My first idea was "snake", but that comes with the SDK. Same with a side-scrolling shooter. Remaining ideas include a tower defense game (hard to write, hard to control), an RPG (same), tetris (lame).. The problem is that all of the games I like require a high-resolution screen because they have a lot of text. Even a really simple game like nethack would be hard because each creature would be a single color. tl;dr What styles of games require a. No text; and b. Few enough objects that representing them each with a single color is acceptable? EDIT: To clarify, the display is 8x8 for a total of 64 pixels, not 64x64.

  Read the article

• correct Installation and configuration of openJDK and R

  - by Marco K

  I am relatively new to Ubuntu so I wont know a lot of commands that probably became standard to a lot of you guys. I am trying to set up R and with it the necessary java dependencies to install e.g. JGR, rjava, etc. I read through quite a few instructions to do that but somehow I must have done sth wrong. Here is the state of R and java: R --version R version 2.14.1 (2011-12-22) Copyright (C) 2011 The R Foundation for Statistical Computing ISBN 3-900051-07-0 Platform: x86_64-pc-linux-gnu (64-bit) java -version java version "1.6.0_23" OpenJDK Runtime Environment (IcedTea6 1.11pre) (6b23~pre11-0ubuntu1.11.10.1) OpenJDK 64-Bit Server VM (build 20.0-b11, mixed mode) R CMD javareconf Java interpreter : /usr/bin/java Java version : 1.6.0_23 Java home path : /usr/lib/jvm/java-6-openjdk/jre Java compiler : /usr/bin/javac Java headers gen.: /usr/bin/javah Java archive tool: /usr/bin/jar Java library path: /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/server:/usr/lib/jvm/java-6-openjdk/jre/lib/amd64:/usr/lib/jvm/java-6-openjdk/jre/../lib/amd64:/usr/java/packages/lib/amd64:/usr/lib/jni:/lib:/usr/lib JNI linker flags : -L/usr/lib/jvm/java-6-openjdk/jre/lib/amd64/server -L/usr/lib/jvm/java-6-openjdk/jre/lib/amd64 -L/usr/lib/jvm/java-6-openjdk/jre/../lib/amd64 -L/usr/java/packages/lib/amd64 -L/usr/lib/jni -L/lib -L/usr/lib -ljvm JNI cpp flags : But when I try to install 'JavaGD' in R, which is a dependency for JGR I get: ... checking Java support in R... present: interpreter : '/usr/bin/java' cpp flags : '' java libs : '-L/usr/lib/jvm/java-6-openjdk/jre/lib/amd64/server -L/usr/lib/jvm/java-6-openjdk/jre/lib/amd64 -L/usr/lib/jvm/java-6-openjdk/jre/../lib/amd64 -L/usr/java/packages/lib/amd64 -L/usr/lib/jni -L/lib -L/usr/lib -ljvm' configure: error: One or more Java configuration variables are not set. Make sure R is configured with full Java support (including JDK). Run R CMD javareconf as root to add Java support to R. ... Any help would be greatly appreciated. Thanks!

  Read the article

• Backup Failed, need help not failing

  - by Costa

  Backup (Deja Dup) failed to do an initial backup to my Amazon S3, and despite my best Googling efforts, I could not find a solution : ( Here's the error message: BackendException: Error uploading s3+http://deja-dup-auto-akiaiksyiqi3buaaz26a/My-Archive/duplicity-full.20130805T143807Z.vol1.difftar.gpg I'm running Ubuntu 12.04 LTS on a System76. The folder I'm trying to backup to in S3 is set to store as Amazon Glacier Storage. Any help would rock! Update: better debugging info: DUPLICITY: . Failed to create bucket (attempt #1) 'deja-dup-auto-axxxxxxxxxxxa' failed (reason: S3ResponseError: S3ResponseError: 403 Forbidden DUPLICITY: . <?xml version="1.0" encoding="UTF-8"?> DUPLICITY: . <Error><Code>SignatureDoesNotMatch</Code><Message>The request signature we calculated does not match the signature you provided. Check your key and signing method.</Message><StringToSignBytes>47 00 54 0a 0a 0a 4d 6f 6e 00 20 30 35 20 00 75 67 20 32 30 31 00 00 35 00 32 34 3a 31 32 20 47 4d 00 0a 2f 64 65 6a 61 2d 64 75 70 2d 61 75 74 6f 2d 61 6b 69 00 6b 73 79 69 71 69 33 62 75 61 00 7a 32 36 61 2f</StringToSignBytes><RequestId>8000000000003</RequestId><HostId>Uxxxxxxxxxxxxxxxxx/xxxxxxxxxxxxxxxxRF</HostId><SignatureProvided>yxxxxxxxxxxxxxxxxxxxxx</SignatureProvided><StringToSign>GET

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• [Kubuntu 14.04][Eclipse] (ADT) crashes at button OK from Project properties

  - by nouseforname

  Since i upgraded to kubuntu 14.04, my Eclipse crashes at different situations. Mostly i can "simulate" it when going to project properties and press ok. Then it always crashes. My system: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=14.04 DISTRIB_CODENAME=trusty DISTRIB_DESCRIPTION="Ubuntu 14.04.1 LTS" My Java: java version "1.8.0_05" Java(TM) SE Runtime Environment (build 1.8.0_05-b13) Java HotSpot(TM) 64-Bit Server VM (build 25.5-b02, mixed mode) My ADT Version: Android Development Toolkit Version: 23.0.0.1245622 I already tried to add this in adt-bundle-linux-x86_64/eclipse/configuration/configuration.ini org.eclipse.swt.browser.DefaultType=mozilla -Dorg.eclipse.swt.browser.DefaultType=mozilla Error: # # A fatal error has been detected by the Java Runtime Environment: # # SIGSEGV (0xb) at pc=0x00007fe049eb1718, pid=5964, tid=140601811232512 # # JRE version: Java(TM) SE Runtime Environment (8.0_05-b13) (build 1.8.0_05-b13) # Java VM: Java HotSpot(TM) 64-Bit Server VM (25.5-b02 mixed mode linux-amd64 compressed oops) # Problematic frame: # C [libgobject-2.0.so.0+0x19718] g_object_get_qdata+0x18 # # Core dump written. Default location: /home/maddin/core or core.5964 # # An error report file with more information is saved as: # /home/maddin/hs_err_pid5964.log Compiled method (nm) 28866 4166 n 0 org.eclipse.swt.internal.gtk.OS::_g_object_get_qdata (native) total in heap [0x00007fe051da6790,0x00007fe051da6af0] = 864 relocation [0x00007fe051da68b0,0x00007fe051da68f8] = 72 main code [0x00007fe051da6900,0x00007fe051da6ae8] = 488 oops [0x00007fe051da6ae8,0x00007fe051da6af0] = 8 # # If you would like to submit a bug report, please visit: # http://bugreport.sun.com/bugreport/crash.jsp # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # Now, as soon as i change SystemSettings - Application Apperance - GTK - GTKn-Design to something else but "oxygen-gtk" this crash doesn't happen anymore. But the application appearance also is ugly. Beside that i get a lot of errors/warnings like that: (SWT:6148): GLib-GObject-CRITICAL **: g_closure_add_invalidate_notifier: assertion 'closure->n_inotifiers < CLOSURE_MAX_N_INOTIFIERS' failed or other GTK warnings from the particular design, not having theme-engine. Which actually doesn't cause any crahs it seems so far. So i have 3 options: accept crashes accept warnings (maybe the best choice) accept ugly design What can i do to solve this issue without changing the design settings?

  Read the article

• Screen flickering when using midrange brightness values on Dell XPS

  - by Eliran Malka

  After a fresh Ubuntu install on my laptop, I discovered the function keys for screen brightness control (Fn+F4 and Fn+F5) are not working. Digging around here, I managed to get it to work by following the solution suggested on this post and that one, but alas — after applying it, a strange problem occurred: Setting the brightness level to any value other than minimum or maximum, the screen starts flickering back and forth from the selected level to full brightness, apparently due to Dell's power saver attempting to dim the screen to adjust the brightness levels. I looked up for a solution here on the site, and possibly everywhere, with no avail. Also tried: To manually control the brightness by configuring the ACPI level (setting values by echo [some_value] | sudo tee /sys/class/backlight/[vendor]_backlight/[some_key], without success. Installing the Intel graphics driver, thinking it's missing. Realized it's installed out of the box by installing Mesa Utils. How to resolve this? Environment Model: Dell Studio XPS 13 OS: Windows 7 64bit / Ubuntu 12.04 32bit (dual boot) Graphics Driver: Intel HD 3000 (Sandybridge Mobile x86/MMX/SSE2) lshw -C display output: *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:f0000000-f03fffff memory:e0000000-efffffff ioport:2000(size=64)

  Read the article

• can't run sqldeveloper on Ubuntu

  - by nazar_art

  I tried to install sqldeveloper by following way: Download SQL Developer from Oracle website (I chose Other Platforms download). Extract file to /opt: sudo unzip sqldeveloper-*-no-jre.zip -d /opt/ sudo chmod +x /opt/sqldeveloper/sqldeveloper.sh Linking over an in-path launcher for Oracle SQL Developer: sudo ln -s /opt/sqldeveloper/sqldeveloper.sh /usr/local/bin/sqldeveloper Edit /usr/local/bin/sqldeveloper.sh replace it's content to: #!/bin/bash cd /opt/sqldeveloper/sqldeveloper/bin ./sqldeveloper "$@" Run SQL Developer: sqldeveloper But it shows next output: nazar@lelyak-desktop:/opt/sqldeveloper? ./sqldeveloper.sh Oracle SQL Developer Copyright (c) 1997, 2014, Oracle and/or its affiliates. All rights reserved. LOAD TIME : 401# # A fatal error has been detected by the Java Runtime Environment: # # SIGSEGV (0xb) at pc=0x00007f3b2dcacbe0, pid=20351, tid=139892273444608 # # JRE version: Java(TM) SE Runtime Environment (7.0_65-b17) (build 1.7.0_65-b17) # Java VM: Java HotSpot(TM) 64-Bit Server VM (24.65-b04 mixed mode linux-amd64 compressed oops) # Problematic frame: # C 0x00007f3b2dcacbe0 # # Core dump written. Default location: /opt/sqldeveloper/sqldeveloper/bin/core or core.20351 # # An error report file with more information is saved as: # /tmp/hs_err_pid20351.log # # If you would like to submit a bug report, please visit: # http://bugreport.sun.com/bugreport/crash.jsp # /opt/sqldeveloper/sqldeveloper/bin/../../ide/bin/launcher.sh: line 1193: 20351 Aborted (core dumped) ${JAVA} "${APP_VM_OPTS[@]}" ${APP_ENV_VARS} -classpath ${APP_CLASSPATH} ${APP_MAIN_CLASS} "${APP_APP_OPTS[@]}" 134 nazar@lelyak-desktop:/opt/sqldeveloper? java -version java version "1.7.0_65" Java(TM) SE Runtime Environment (build 1.7.0_65-b17) Java HotSpot(TM) 64-Bit Server VM (build 24.65-b04, mixed mode) Here is content of /tmp/hs_err_pid20351.log How to solve this trouble?

  Read the article

• cpufreq not available 11.10

  - by code shogan

  on 11.04 I had cpufreq working on my "AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02" processors, however now on oneiric cpufreq won't load. The core temperature of my cpu is normally 40 c, but lately it's cooking away at 75-80+ c and the fan is always extremely loud even when cpu usage has at 0.4%. and after this dmesg | grep -i cpu I got: Brought up 2 CPUs Switch to broadcast mode on CPU1 Switch to broadcast mode on CPU0 Switched to NOHz mode on CPU #1 Switched to NOHz mode on CPU #0 ACPI: acpi_idle registered with cpuidle cpufreq-nforce2: No nForce2 chipset. cpuidle: using governor ladder cpuidle: using governor menu powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-50 (2 cpu cores) (version 2.20.00) I see something about governors and ladder there, does this mean the OS is able to scale my cpu's or not? If so is there a way I can determine it's working? I saw that for other users that the wrong module had been loaded and by disabling it they were able to get cpufreq loaded. How can I tell what scaling module is loaded? stats: Ubuntu Oneiric 32bit Dell Inspiron 1501

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• Why am I not getting an sRGB default framebuffer?

  - by Aaron Rotenberg

  I'm trying to make my OpenGL Haskell program gamma correct by making appropriate use of sRGB framebuffers and textures, but I'm running into issues making the default framebuffer sRGB. Consider the following Haskell program, compiled for 32-bit Windows using GHC and linked against 32-bit freeglut: import Foreign.Marshal.Alloc(alloca) import Foreign.Ptr(Ptr) import Foreign.Storable(Storable, peek) import Graphics.Rendering.OpenGL.Raw import qualified Graphics.UI.GLUT as GLUT import Graphics.UI.GLUT(($=)) main :: IO () main = do (_progName, _args) <- GLUT.getArgsAndInitialize GLUT.initialDisplayMode $= [GLUT.SRGBMode] _window <- GLUT.createWindow "sRGB Test" -- To prove that I actually have freeglut working correctly. -- This will fail at runtime under classic GLUT. GLUT.closeCallback $= Just (return ()) glEnable gl_FRAMEBUFFER_SRGB colorEncoding <- allocaOut $ glGetFramebufferAttachmentParameteriv gl_FRAMEBUFFER gl_FRONT_LEFT gl_FRAMEBUFFER_ATTACHMENT_COLOR_ENCODING print colorEncoding allocaOut :: Storable a => (Ptr a -> IO b) -> IO a allocaOut f = alloca $ \ptr -> do f ptr peek ptr On my desktop (Windows 8 64-bit with a GeForce GTX 760 graphics card) this program outputs 9729, a.k.a. gl_LINEAR, indicating that the default framebuffer is using linear color space, even though I explicitly requested an sRGB window. This is reflected in the rendering results of the actual program I'm trying to write - everything looks washed out because my linear color values aren't being converted to sRGB before being written to the framebuffer. On the other hand, on my laptop (Windows 7 64-bit with an Intel graphics chip), the program prints 0 (huh?) and I get an sRGB default framebuffer by default whether I request one or not! And on both machines, if I manually create a non-default framebuffer bound to an sRGB texture, the program correctly prints 35904, a.k.a. gl_SRGB. Why am I getting different results on different hardware? Am I doing something wrong? How can I get an sRGB framebuffer consistently on all hardware and target OSes?

  Read the article

• New SQLOS features in SQL Server 2012

  - by SQLOS Team

  Here's a quick summary of SQLOS feature enhancements going into SQL Server 2012. Most of these are already in the CTP3 pre-release, except for the Resource Governor enhancements which will be in the release candidate. We've blogged about a couple of these items before. I plan to add detail. Let me know which ones you'd like to see more on: - Memory Manager Redesign: Predictable sizing and governing SQL memory consumption: sp_configure ‘max server memory’ now limits all memory committed by SQL ServerResource Governor governs all SQL memory consumption (other than special cases like buffer pool) Improved scalability of complex queries and operations that make >8K allocations Improved CPU and NUMA locality for memory accesses Single memory manager that handles page allocations of all sizes Consistent Out-of-memory handling & management across different internal components - Optimized Memory Broker for Column Store indexes (Project Apollo) - Resource Governor Support larger scale multi-tenancy by increasing Max. number of resource pools20 -> 64 [for 64-bit] Enable predictable chargeback and isolation by adding a hard cap on CPU usage Enable vertical isolation of machine resources Resource pools can be affinitized to individual or groups of schedulers or to NUMA nodes New DMV for resource pool affinity  - CLR 4 support, adds .NET Framework 4 advantages - sp_server_dianostics Captures diagnostic data and health information about SQL Server to detect potential failures Analyze internal system state Reliable when nothing else is working   - New SQLOS DMVs (in 2008 R2SP1) SQL Server related configuration - New DMVsys.dm_server_services OS related resource configurationNew DMVssys.dm_os_volume_statssys.dm_os_windows_infosys.dm_server_registry XEvents for SQL and OS related Perfmon counters Extend sys.dm_os_sys_info See previous blog posts here and here. - Scale / Mission critical Increased scalability: Support Windows 8 max memory and logical processorsDynamic Memory support in Standard Edition - Hot-Add Memory enabled when virtualized - Various Tier1 Performance Improvements, including reduced instructions for superlatches. Originally posted at http://blogs.msdn.com/b/sqlosteam/

  Read the article

• A Consol Application or Windows Application in VS 2010 for Sharepoint 2010 : A common Error

  - by Gino Abraham

  I have seen many Sharepoint Newbies cracking their head to create a Console/Windows  application in VS2010 and make it talk to Sharepoint 2010 Server. I had the same problem when i started with Sharepoint in the begining. It is important for you to acknowledge that SharePoint 2010 is based on .NET Framework version 3.5 and not version 4.0. In VS 2010 when you create a Console/Windows application, Make Sure you select .Net Framework 3.5 in the New Project Dialog Window.If you have missed while creating new Project Go to the Application tab of project properties and verify that .NET Framework Version 3.5 is select as the Target Framework. Now that you have selected the correct framework, will it work? Nope if the application is configured as x86 one it will not work. Sharepoint is a 64 Bit application and when you create a windows application to talk to Sharepoint it should also be a 64 Bit one. Go to Configuration Manager, Select x64. If x64 is not available select <New…> and in the New Solution Platform dialog box select x64 as the new platform copying settings from x86 and checking the Create new project platforms check box. This is not applicable if you are making a console application to talk to sharepoint with Client Object Model.

  Read the article

• I cannot install anything in ubuntu that has dependency problem

  - by phpGeek

  I wanted to install teamviewer on linux 64-bit system. What I did was to download teamviewer.deb file and install it as below: sudo dpkg -i install teamviewer.deb Then I wanted to correct dependency problem so I issued the following command: sudo apt-get install libc6:i386 libgcc1:i386 libasound2:i386 libfreetype6:i386 zlib1g:i386 libsm6:i386 libxdamage1:i386 libxext6:i386 libxfixes3:i386 libxrender1:i386 libxtst6:i386 I got the following error: E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies I then tried: sudo apt-get install -f Again I got the following error: E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies Even I tried to install gdebi, but I got the above error again. I emptied archives folder: sudo apt-get clean sudo apt-get update sudo apt-get upgrade Again I have problem installing my deb package. Is there anything I could do now to solve this problem? I've read the below article as well: Install Teamviewer using a 64-bits system but I get a dependency error EDIT: I found libperl5.14:amd64 as a broken package. I used: sudo apt-get remove libperl5.14:amd64 I got the following message: E: Unable to locate package Broken

  Read the article

• Leveraging .Net 4.0 Framework Tools For Encrypting Web Configuration Sections

  - by Sam Abraham

  I would like to share a few points with regards to encrypting web configuration sections in .Net 4.0. This information is also applicable to .Net 3.5 and 2.0. Two methods can work perfectly for encrypting connection strings in a Web project configuration file:   1-Do It All Yourself! In this approach, helper functions for encrypting/decrypting configuration file content are implemented. Program would explicitly retrieve appropriate content from configuration file then decrypt it appropriately.  Disadvantages of this implementation would be the added overhead for maintaining the encryption/decryption code as well the burden of always ensuring sections are appropriately decrypted before use and encrypted appropriately whenever edited.   2- Leverage the .Net 4.0 Framework (The Way to go!) Fortunately, all needed tools for protecting configuration files are built-in to the .Net 2.0/3.5/4.0 versions with very little setup needed. To encrypt connection strings, one can use the ASP.Net IIS Registration Tool (Aspnet_regiis.exe). Note that a 64-bit version of the tool also exists under the Framework64 folder for 64-bit systems. The command we need to encrypt our web.config file connection strings is simply the following:   Aspnet_regiis –pe “connectionstrings” –app “/sampleApplication” –prov “RsaProtectedConfigurationProvider”   To later decrypt this configuration section:   Aspnet_regiis –pd “connectionstrings” –app “/SampleApplication”   The following is a brief description of the command line options used in the example above. Aspnet_regiis supports many more options which you can read about in the links provided for reference below.   Option Description -pe  Section name to encrypt -pd  Section name to decrypt -app  Web application name -prov  Encryption/Decryption provider   ASP.Net automatically decrypts the content of the Web.Config file at runtime so no programming changes are needed.   Another tool, aspnet_setreg.exe is to be used if certain configuration file sections pertinent to the .Net runtime are to be encrypted. For more information on when and how to use aspnet_setreg, please refer to the references below.   Hope this helps!   Some great references concerning the topic:   http://msdn.microsoft.com/en-us/library/ff650037.aspx http://msdn.microsoft.com/en-us/library/zhhddkxy.aspx http://msdn.microsoft.com/en-us/library/dtkwfdky.aspx http://msdn.microsoft.com/en-us/library/68ze1hb2.aspx

  Read the article

• Unity 3D does not work on Dell system with a AMD Radeon HD 6470M

  - by VeeKay

  I am running 64 bit Ubuntu on Dell with 1GB graphic card. I login with "Ubuntu" hoping to see Unity 3d but it doesn't. Unity 2D runs instead. when I type in echo "$DESKTOP_SESSION" it confirms the Unity-2D. I've checked the System info that shows like : The graphics row shows itself as empty. SO I've presumed that the graphic drivers aren't detected and hence I went to Unity- Additional Drivers and installed the fglrx driver that the UI has suggested. Even after installing so, the graphics part in System info details shows nothing and still Unity 2D runs in spite of all the effort. Please help! How can I get my Unity 3D back? Hardware Info Video Card : AMD Radeon™ HD 6470M - 1GB (For ICC) RAM : 6GB (1 X 2GB + 1 X 4GB) 2 DIMM DDR3 1333Mhz OS : 64 bit Ubuntu 11.10 Edit : Output for /usr/lib/nux/unity_support_test -p X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 155 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 21 Current serial number in output stream: 21

  Read the article

• Can't Start ISC DHCP IPv6 Server

  - by MrDaniel

  Trying to enable the ISC DHCP server for just IPv6 on Ubuntu 12.04 LTS. I have downloaded and installed the DHCP server via the following command: $ sudo apt-get install isc-dhcp-server Then I have followed the instructions in the following resources, Ubuntu Wiki DHCPv6, SixXS - Configuring ISC DHCPv6 Server and Linux IPv6 HOWTO - Configuration of the ISC DHCP server for IPv6 . So from review all those resources it seems like I need to: set a static IPv6 address for the Interface I want to run the DHCPv6 server from that is part of the IPv6 network subnet outside the DHCP range. Edit the /etc/dhcp/dhcpd6.conf file to configure the DHCPv6 range etc. Create the /var/lib/dhcp/dhcpd6.leases Manually start the DHCPv6 server. Setting the Static IP for eth0 $ sudo ifconfig eth0 inet6 add 2001:db8:0:1::128/64 My dhcpd6.conf default-lease-time 600; max-lease-time 7200; log-facility local7; subnet6 2001:db8:0:1::/64 { #Range for clients range6 2001:db8:0:1::129 2001:db8:0:1::254; } Created the dhcpd6.leases file As indicated in the dhcpd.leases man page. $ touch /var/lib/dhcp/dhcpd6.leases #Tried with sudo as well Manually starting the DHCPv6 server. Attempted to start the server using the following command: $ sudo dhcp -6 -f -cf /etc/dhcp/dhcpd6.conf eth0 The problem, the DHCP will not start, with an append error for the dhcpd6.leases file as indicated below when running the manual start command noted above. Can't open /var/lib/dhcp/dhcpd6.leases for append. Any ideas what I might be missing?

  Read the article

• Accessing second hard drive

  - by Jonathan

  Hi, So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris

  Read the article

• Cannot establish Wired connection on Acer Aspire 5930G

  - by drakos46

  I use an Acer Aspire 5930G, dual booted with Windows 7 and Ubuntu 13.10. My problem is that i cannot establish wired connection on my ubuntu. Wireless connection works in both of my OSs but the Wired connection does not, only on the Ubuntu. I have already tried the common fix: echo on | sudo tee /sys/class/net/eth0/device/power/control but without any results. Any ideas? eth0 Link encap:Ethernet HWaddr 00:1d:72:c2:21:a5 inet6 addr: fe80::21d:72ff:fec2:21a5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:945 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:204318 (204.3 KB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:7241 errors:0 dropped:0 overruns:0 frame:0 TX packets:7241 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:645874 (645.8 KB) TX bytes:645874 (645.8 KB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:57:7b:cc inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::216:eaff:fe57:7bcc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:19937 errors:0 dropped:0 overruns:0 frame:0 TX packets:16933 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10877245 (10.8 MB) TX bytes:3131378 (3.1 MB) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8071 PCI-E Gigabit Ethernet Controller (rev 16)

  Read the article

• Struggles to connect to network when using WPA with a BCM43225

  - by pst007x

  When booting my laptop, it will try to connect to my wireless network, however a window keeps popping up asking me for my security password, which has already been saved. I have to keep deleting my network settings, and reconnecting, otherwise it keeps failing to connect. My wireless is set up with a WPA, I do not want to lower my security because of this, but it is a pain and can take me 15mins plus to finally connect. The problem has only become apparent since a fresh install of 11.10. IPV6 disabled. System info: 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) Subsystem: Acer Incorporated [ALI] Device 036d Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at b3400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: tg3 Kernel modules: tg3 02:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) Subsystem: Broadcom Corporation Device 04da Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at b2400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: wl, brcmsmac ADDITIONAL: In terminal I get this: pst007x@pst007x-ubuntu64:~$ nm-applet start ** Message: applet now removed from the notification area ** (nm-applet:2816): DEBUG: old state indicates that this was not a disconnect 0 ** Message: using fallback from indicator to GtkStatusIcon ** Message: applet now embedded in the notification area ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. ** (nm-applet:2816): DEBUG: foo_client_state_changed_cb Note this line: ** Message: No keyring secrets found for Auto Access 01/802-11-wireless-security; asking user. At this point is where I am asked for the password. Please report WPA issues with Ubuntu 11.10 here: https://bugs.launchpad.net/ubuntu/+source/network-manager/+bug/892727

  Read the article

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• Video game "Gish" will only launch from command line

  - by aberration

  Platform: Lubuntu 11.10 x64 Program: Gish When I try to launch Gish from the command line (/opt/gish/gi.sh), there are no problems. But when I try to launch it from the LXDE menu, it will not start. Contents of /usr/share/applications/gish.desktop: [Desktop Entry] Categories=Game;ActionGame;AdventureGame;ArcadeGame; Exec=/opt/gish/gi.sh Path=/opt/gish Icon=x-gish Terminal=false Type=Application Name=Gish I tried changing Terminal=false to Terminal=true to debug it, but then I just got a blank terminal, and the game didn't start. Edit: Here is some additional information, as requested by Eliah Kagan below: I tried editing /usr/share/applications/gish.desktop, as recommended, but it had no effect However, ~/.xsession-errors contained the following error: [: 8: x86_64: unexpected operator ./gish_32: error while loading shared libraries: libGL.so.1: wrong ELF class: ELFCLASS64 I think there's a problem with the /opt/gish/gi.sh shell script. This is its contents: cd /opt/gish/ MACHINE_TYPE=`uname -m` if [ ${MACHINE_TYPE} == 'x86_64' ]; then ./gish_64 else ./gish_32 fi I'm not too familiar with Bash, so hopefully someone else can point out the error. I have a 64-bit machine. I think that when the script is run from the command line, it's properly launching the 64-bit version (/opt/gish/gish_64), but when it's run from the LXDE menu, it's launching the 32-bit version (/opt/gish/gish_32), which is causing the libGL.so.1 error. However, this may be related to my libGL.so.1 problems with 2 other games.

  Read the article

• How to get a Toshiba L505 to boot USB or CD

  - by ShroudedCloud

  OK, have a Toshiba L505 (not sure of the extended model number) that got a virus on Windows and will no longer will boot into that, so I'm trying to revive it with Ubuntu. Problem is, when I tell it to boot into a USB image of 12.04 32- or 64-bit, 13.04 64-bit, or elementary Luna 32-bit, it gives me some screen with a copyright from 2000 for Intel, invariably spits out a "media not recognized" type of error and then says PXE-ROM exiting. Well, that's annoying. So I went in with a CD (12.04 x86_64 having tried 32-bit in the past as well). Boot menu, select, starts running. Seeing the loading screen for Ubuntu, going well... until it's not. Again, invariably, it fails. The CD drive will cease spinning at around the same time each time and then the laptop will stop doing everything altogether (at least, everything spins down and it goes quiet). As far as I can tell, it's not to do with what function is being loaded from the CD at the time (because that bit is variable). I'd love to be able to boot from USB (since it will be all but required going forward), but getting the CD to work would be wondrous too. Anyone have any ideas of where I can go from here to try to fix this? My friends and I have turned up nothing.

  Read the article

• pppoe connection to dsl model

  - by VJo

  Hello, I am connecting to the internet through a pppoe connection, but for some reason I can not connect to my modem (it's address is 192.168.1.1). Before I set my pppoe connection, I could connect. So, is there a way? EDIT The output of ifconfig is : r@PlaviZec:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:13:d4:f7:02:d4 inet6 addr: fe80::213:d4ff:fef7:2d4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2811 errors:0 dropped:0 overruns:0 frame:0 TX packets:2801 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2538831 (2.5 MB) TX bytes:448591 (448.5 KB) Interrupt:21 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:28 errors:0 dropped:0 overruns:0 frame:0 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1600 (1.6 KB) TX bytes:1600 (1.6 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:92.229.42.177 P-t-P:213.191.64.59 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:2794 errors:0 dropped:0 overruns:0 frame:0 TX packets:2741 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:2476277 (2.4 MB) TX bytes:381240 (381.2 KB)

  Read the article

• A Console Application or Windows Application in VS 2010 for Sharepoint 2010 : A common Error

  - by Gino Abraham

  I have seen many Sharepoint Newbies cracking their head to create a Console/Windows  application in VS2010 and make it talk to Sharepoint 2010 Server. I had the same problem when i started with Sharepoint in the begining. It is important for you to acknowledge that SharePoint 2010 is based on .NET Framework version 3.5 and not version 4.0. In VS 2010 when you create a Console/Windows application, Make Sure you select .Net Framework 3.5 in the New Project Dialog Window.If you have missed while creating new Project Go to the Application tab of project properties and verify that .NET Framework Version 3.5 is select as the Target Framework. Now that you have selected the correct framework, will it work? Nope if the application is configured as x86 one it will not work. Sharepoint is a 64 Bit application and when you create a windows application to talk to Sharepoint it should also be a 64 Bit one. Go to Configuration Manager, Select x64. If x64 is not available select <New…> and in the New Solution Platform dialog box select x64 as the new platform copying settings from x86 and checking the Create new project platforms check box. This is not applicable if you are making a console application to talk to sharepoint with Client Object Model.

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >