Search Results

Search found 2740 results on 110 pages for 'blue river'.

Page 95/110 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

  • GRUB 2 freezing at OS selection screen, what could be the cause?

    - by Michael Kjörling
    Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

    Read the article

  • NTPD seems to delete all network interfaces

    - by Aurelin
    We have a couple of virtual interfaces configured on eth0 on a CentOS, and every now and then, they went down seemingly out of the blue. Now after going through the log files, I found out that apparently ntpd deletes all eth0 interfaces, and that dhclient automatically brings eth0 back up. The virtual interfaces, however, stay down which causes several of our websites to be inaccessible. Can someone explain to me why ntpd deletes interfaces? Can / should that be turned off, or can / should I configure dhclient to bring the virtual interfaces back up automatically, too? EDIT// The log files that I should've posted : Nov 12 13:10:28 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x6a825e97) Nov 12 13:10:42 raptor dhclient[20048]: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPOFFER from 96.126.108.78 Nov 12 13:10:42 raptor dhclient[20048]: DHCPREQUEST on eth0 to 255.255.255.255 port 67 (xid=0x24554092) Nov 12 13:10:42 raptor dhclient[20048]: DHCPACK from 96.126.108.78 (xid=0x24554092) Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #31 eth0, 50.116.50.97#123, interface stats: received=3255, sent=3256, dropped=0, active_time=1559394 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #32 eth0:0, 50.116.53.56#123, interface stats: received=3, sent=0, dropped=0, active_time=1559391 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #33 eth0:1, 66.175.211.192#123, interface stats: received=2, sent=0, dropped=0, active_time=1559389 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #34 eth0:2, 50.116.53.95#123, interface stats: received=3, sent=0, dropped=0, active_time=1559387 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #35 eth0:3, 97.107.132.32#123, interface stats: received=2, sent=0, dropped=0, active_time=1559385 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #36 eth0:4, 50.116.56.201#123, interface stats: received=2, sent=0, dropped=0, active_time=1559383 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #37 eth0:5, 66.175.212.121#123, interface stats: received=2, sent=0, dropped=0, active_time=1559381 secs Nov 12 13:10:42 raptor ntpd[2109]: Deleting interface #38 eth0:6, 66.175.215.137#123, interface stats: received=2, sent=0, dropped=0, active_time=1559379 secs Nov 12 13:10:44 raptor NET[1573]: /sbin/dhclient-script : updated /etc/resolv.conf Nov 12 13:10:44 raptor dhclient[20048]: bound to 50.116.50.97 -- renewal in 32692 seconds. Nov 12 13:10:45 raptor ntpd[2109]: Listening on interface #39 eth0, 50.116.50.97#123 Enabled The eth0 config : DEVICE="eth0" ONBOOT="yes" BOOTPROTO="dhcp" IPV6INIT="no" IPADDR=50.116.50.97 NETMASK=255.255.255.0 GATEWAY=50.116.50.1 And the virtual interfaces (I posted the first one only, they look the same for the most part) : # Configuration for eth0:0 DEVICE=eth0:0 BOOTPROTO=none # This line ensures that the interface will be brought up during boot. ONBOOT=yes # eth0:0 IPADDR=50.116.53.56 NETMASK=255.255.255.0

    Read the article

  • Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

    - by user95917
    hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

    Read the article

  • Archlinux/atheros WLAN configuration troubles

    - by GrinReaper
    I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

    Read the article

  • Optimal setup for ASUS P6X58D Premium BIOS (no OC)?

    - by rumtscho
    Normally, I'd trust the mainboard manufacturer to choose the best options as defaults. But I had trouble with the board, because even with Quick Boot enabled, it booted twice as slowly as a Pentium 4 Celeron. Then I changed lots of options at once (most of them weren't explained in the manual, just mentioned with a single sentence) and the boot time is only marginally worse than the Pentium 4 (54 sec against 46 sec from button to pw entering screen). Now I don't know if I have turned something off which should have stayed on. I guess I even won't be able to boot from a CD now, because even though it is present in the boot sequence, I took off a timeout I think it needs to check whether there is a disk in the drive. The second reason is that I don't have an internal HDD, only a SSD. I forgot my sources blush but I am under the impression that today's BIOS and OS options are geared toward booting from a HDD, which is often less than optimal when one boots from a SSD, especially when there are functions which cause avoidable writing cycles, as a SSD wears out after too many writing cycles. Most of the things I've read concern the OS, but there are some BIOS-relevant options too. I am especially confused about the disk mode. The board supports AHCI, IDE-simulation and RAID, but of the different articles I've read, there is a proponent for each and no clear arguments for any. So can one tell me which options are important in general and which are important for a SSD-only system? I don't want to overclock the CPU, so you don't have to say anything about this (yes I know the board is meant for OC:)). I am thinking of overclocking the RAM, since they sold me 1600er heatsinked modules which are running at 1066 now, but I'm not sure yet about that. The rest of the system: i7-930, Intel X25-m G2, 6 GB RAM, GTS 250, some no-name Blue-ray ROM. 2 external HDDs over USB 2.0. Lots of other USB-connected hardware (12 devices I think), no SATA 3 drives (will disabling the controller have an impact on performance?), no LAN, only WiFi. Lucid Lynx 64 bit, no dual boot, no virtual installations. The main uses of the system are: managing and playing/showing all the media stored on the external disks, lots of image manipulation, some video editing, a bit of (non-demanding) gaming, rarely development. Lots of Internet surfing too, but this shouldn't have much impact on performance.

    Read the article

  • SSD Fresh Does Not Start

    - by Jim Fell
    I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fress from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried shutting down the Spybot Resident and disabling the firewall and virus scanner with no luck. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

    Read the article

  • installing windows XP in Samsung SENS 145 plus notebook (no CD drive)

    - by user13267
    Hi I was trying to install Windows XP in a Samsung SENS 145 plus Notebook. It does not have a cd drive and I already managed to format it and semi install Windows XP, so now it does not even boot up either. This is what I did: Since it supports USB booting, I first made a bootable USB of Windows XP (Korean version; SP2 I think, may be SP 3) using Novicorp WinToFlash enter link description here. It managed to boot up at first and I was able to format the C driveand get Windows install to start up. It took forever to copy all the files from the USB and after the first reboot, before installation started, I cancelled the reboot from windows install, went to BIOS and changed the boot device priority from USB to internal hard drive. But now on bootup it showed me a list with two options for booting windows XP (much like in the case of a multi OS system) so I assumed that I had formatted drive D by mistake and installed XP there, instead of on C drive. Anyway, I chose one of them and it continued my Windows installation. I got the blue installation screen that shows ads about Windows XP on the right frame and estimated remaining time on the left. However, after completing the process, after the first reboot, instead of showing the Windows XP logo, it says \system32\hall.dll is missing (or corrupted I'm not sure, I needed to install the Korean version of windows and I could not exactly read the error message, however it was one that I have already seen in an English version installation, and I am sure it says either missing or corrupted). The problem is, now it shows the same error again when I try to reboot it from the USB drive as well. I tried to boot a portable version of Linux I made in another USB, but the computer does not boot up from that USB, and it shows hal.dll error when I try to boot it using the WIN XP installation USB I made, as well as when I try to boot it from the hard drive, where I suppose Win XP is now semiinstalled. So now I can't get the computer to start up at all, except going to the BIOS. What else can I try to solve this? Also, would it be possible to install XP on this computer by connecting it to another one running Windows 7 ultimate, through the ethernet card? That is, network just the two computers together, then install windows XP on the notebook from the desktop running windows 7? Please help, I'm running out of ideas on this one. If Korean version of windows XP is the problem then I am willing to install English version as well. (but I need to make sure if that is the real cause of the problem)

    Read the article

  • My computer's dying :(

    - by j-t-s
    Hi All I have a sweet computer and have never had any real problems with it until now. I recently formatted my computer and all was well. But now my monitor randomly flickers. The monitor will just go black for about a second or two, then it'll return back to its normal state with all the stuff still on the screen. This is getting progressively worse. Another problem that has started is my computer randomly restarts. (I've managed to prevent it from restarting by removing the check in Automatically Restart from the Startup and Recovery Dialog. But I know this doesn't solve the problem). It also completely freezes up on me. One last thing, this morning I got a big blue screen. I can't remember what it said, but if it happens again I will take note of it and repost. Or if I can find some kind of a log file containing that bluescreen error I will post. I have checked all cords, and they're all fine. Nothing's loose. My computer isn't overheating either. I've taken the case off for 3 whole days and haven't used the computer for those 3 days, which has had no effect. I've checked the connections inside and nothing's loose there either. I know there's nothing wrong with my monitor because my friend has 2 computers and it works perfectly on those computers. I don't understand how my computer could suddenly become so unstable. I'm almost certain that I have no viruses; I full-scan my pc everyday for nastys, and have strict firewall settings. Anyway, I don't see how it could be a virus anyway simply due to the fact that I had these problems right after I formatted, and before I even had the chance to install or copy anything or even connect to the internet. I know it has nothing to do with the way I formatted the computer too, I've been fixing computers for years. Sorry for rambling on, just making sure I don't leave anything out. Has anybody else had this problem? Can somebody please try to help me with this? Thank you :)

    Read the article

  • Win 8: Adding a boot volume to an MBR dynamic disk [NOT about changing to basic disks]

    - by Stilez
    (This is NOT aiming to convert to basic disk. In this question, the disk stays dynamic but becomes bootable) There doesn't seem to be a clear, well stated answer I can find, for the question "What are the criteria for Windows 8 to successfully boot from an MBR dynamic disk", or "how do I fix a dynamic MBR partition that's failing boot"? I've tried to educate myself but can't find crucial information to clear it all up. My existing HDD/SSD setup: DISK 0 ~ 60GB SSD/MBR/basic: (350MB recovery)(60GB windows 8 bootable) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISK 2 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISKS 3, 4, 5: (ignored for simplicity: 2xHDD RAID1 + caching SSD) I'm heavy duty on data crunching and virtualisation, just maxxed out 32GB RAM @ 2133 and moved to 4960X + 64GB. Disk 0 is a pure system disk of little value, and virtualisations runs off mirrored SSDs (Samsung 840 Pro 512 x 2) for double speed reading and so they snapshot in reasonable time. I'm using 4 SATA3 ports and the board only has two decent Intel ports (onboard Marvell are poorer quality). I'm wary of choosing between LSI, HighPoint and other 3rd party controllers as I'm unfamiliar with the maze of decent RAID cards (that's a whole other issue!). I want to cut down my SSD needs by moving the boot volume and caching volume to the 840 pros, giving a setup with 2 fewer SSDs: DISK 0 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB boot)(410GB mirrored data) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(30GB cache for the ICH10R mirror)(30GB temp)(410GB mirrored data) DISKS 2, 3: (2xHDD RAID1) Intel's RST allows this, Win 8 allows booting off a MBR/dynamic disk, and the two 60GB SSDs are hardly the fastest SSDs anyway, they'll get repurposed. Moving the caching volume is easy. Moving the boot volume has me stumped. The difficulty is, I'm hitting a wall of knowledge here. I have a UEFI Asus motherboard with an previous traditional MBR/basic boot disk, and I want it to boot from a disk and volume that's MBR/dynamic. The disk copy is physically ok (Partition Wizard Server will copy to dynamic volumes) but then hits a light blue 0xc000000e boot error. No real surprise, I expected to have some boot fixing, but had expected Windows to boot-fix it (all drivers exist), or the usual manual fixes to work. Specifically, I don't know enough, to know what's got to be manually checked and perhaps corrected for the disk to boot (legacy/uefi/bios, odd partitions, boot tables, disk IDs, hidden boot files, oh my!), or if I need to change any of this secure boot/UEFI/legacy stuff in the bios, convert a 512 SSD to basic and then back to dynamic when working, or if the issue is pure OS config using "diskpart", "bootsect" and "bootrec" from the Win8 DVD. The old system disk still boots but I don't know enough to figure what to fix, to make the system boot as I want. The answers probably aren't hard but the real issue is my confusion and missing information. Thanks for helping!

    Read the article

  • CPU overheating after cleaning it

    - by Roberts
    I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

    Read the article

  • Expectations for NTFS file recovery

    - by Fred Hamilton
    Yesterday I booted my XP system, and as I looked up a minute later I saw the light blue screen and tail-end of that pre-boot diskcheck Windows sometimes does if it finds an error (or was previously told to run a diskcheck drung the next boot). I didn't worry about it at the moment... But then I looked at my "scratch" disk, which was a 70% full, 750GB hard disk...and it now looks like it has been freshly formatted. It doesn't have a single file on it, just the hidden "System Volume Information" file and 750GB of freedom from data. I looked at some of the recovery tools from the Free NTFS partition recovery question and decided to try PC INSPECTOR™ File Recovery 4.x initially. It ran overnight and afterwards returned a list of thousands of files it could recover. The odd thing was that the filenames were lost, but the file extensions were not (WTF?). And all of the files were exactly 1,472kB in size. I recovered a dozen PDFs as a test, and 80% of them displayed OK despite being padded out to 1.5MB (though I assume any files 1472kB are hosed). My primary question is: Is this the best I can expect from any file recovery software when trying to recover NTFS files? Or is there perhaps something better out there? I assume this is as good as it gets, but wanted to check in with the experts first. Bonus questions: What might have happened to my drive? I didn't intentionally format it. I've never seen a disk error cause the drive to suddenly become a clean, reformatted drive. Could some malicious/confused software have told my PC to format my disk on reboot? Is that even a function Windows XP has? Why can the file extensions be recovered but not the filename? Does NTFS really treat them as separate entities? I thought I had 8.3 naming turned off, but maybe that had something to do with it. Or maybe it looks at the data in the file and guesses the extension?

    Read the article

  • Recover harddrive data

    - by gameshints
    I have a dell laptop that recently "died" (It would get the blue screen of death upon starting) and the hard drive would make a weird cyclic clicking noises. I wanted to see if I could use some tools on my linux machine to recover the data, so I plugged it into there. If I run "fdisk" I get: Disk /dev/sdb: 20.0 GB, 20003880960 bytes 64 heads, 32 sectors/track, 19077 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Disk identifier: 0x64651a0a Disk /dev/sdb doesn't contain a valid partition table Fine, the partition table is messed up. However if I run "testdisk" in attempt to fix the table, it freezes at this point, making the same cyclical clicking noises: Disk /dev/sdb - 20 GB / 18 GiB - CHS 19078 64 32 Analyse cylinder 158/19077: 00% I don't really care about the hard drive working again, and just the data, so I ran "gpart" to figure out where the partitions used to be. I got this: dev(/dev/sdb) mss(512) chs(19077/64/32)(LBA) #s(39069696) size(19077mb) * Warning: strange partition table magic 0x2A55. Primary partition(1) type: 222(0xDE)(UNKNOWN) size: 15mb #s(31429) s(63-31491) chs: (0/1/1)-(3/126/63)d (0/1/32)-(15/24/4)r hex: 00 01 01 00 DE 7E 3F 03 3F 00 00 00 C5 7A 00 00 Primary partition(2) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) (BOOT) size: 19021mb #s(38956987) s(31492-38988478) chs: (4/0/1)-(895/126/63)d (15/24/5)-(19037/21/31)r hex: 80 00 01 04 07 7E FF 7F 04 7B 00 00 BB 6F 52 02 So I tried to mount just to the old NTFS partition, but got an error: sudo mount -o loop,ro,offset=16123904 -t ntfs /dev/sdb /mnt/usb NTFS signature is missing. Ugh. Okay. But then I tried to get a raw data dump by running dd if=/dev/sdb of=/home/erik/brokenhd skip=31492 count=38956987 But the file got up to 59885568 bytes, and made the same cyclical clicking noises. Obviously there is a bad sector, but I don't know what to do about it! The data is still there... if I view that 57MB file in textpad... I can see raw data from files. How can I get my data back? Thanks for any suggestions, Solution: I was able to recover about 90% of my data: Froze harddrive in freezer Used Ddrescue to make a copy of the drive Since Ddrescue wasn't able to get enough of my drive to use testdisk to recover my partitions/file system, I ended up using photorec to recover most of my files

    Read the article

  • How should I use my new SSD drive?

    - by jasondavis
    I just built a new PC the other day. Specs... Processor: Intel i7-930 quad core CPU CPU Cooler: COOLER MASTER Hyper 212 Motherboard: AsRock X58 Extreme 3 RAM/Memory: 6gb G-Skill tripple channel DDR3 memory (3 sticks of 2gb planning to get another kit to make it 12gb total soon) Operating System Hard drive: Intel X25-M 80GB Mainstream SATA2 Solid State Drive Video Cards: 2 XFX ATI Redeon HD 4650 cards to run 3-4 monitors Case: Lian Li PC-B10 Midtower case Power Supply: Antec TruePower New TP-750 Blue 750W Operating System Windows 7 Pro 64bit Not sure if the specs are helpful at all but I posted them just in case. So I got everything put together and running great so far but I need some advice/ideas/help/tips. I got the SSD drive in hopes of using it strictly for my windows 7 install along with all my other programs I install. I am then going to get another drive or 2 just for data (video,music,photos, etc). So my plan is to just install the new data drives and then in windows 7 I will change my "My documents" "My Music" "My Video" "MY Photos" library's to be located on the data drives instead of the OS SSD drive. I would ultimately like to install all my programs with my windows install on the SSD drive and then create an IMAGE of the drive and then 6 months down the road if things are sluggish I can just wipe the drive and restore my IMAGE with all my programs and settings in tact still. So here are some questions now. 1) How can I verify that TRIM is working on my new SSD? 2) Is there anything above that I missed that I should be doing? I think I once read that there is a page file or some sort of file that windows changes a lot and that it should be moved off f an SSD an onto my data drives. DOes anyone know what I might of heard? If you do can you explain the pros and cons of doing such a thing as well as how to possibly? 3) Any tips or advice to get the best performance from all this, I built a pretty nice system and I just want to make it stay that way as long as I can.

    Read the article

  • Recognizing Dell EquilLogic with Nagios

    - by user3677595
    EDIT: All firmware and models are compatible, that is why nothing is posted about it. Okay, so there will be a lot here, so please bare with me. I've been working on this now for a few hours (reading manuals and such) so I'm not just coming here right out of the blue. I am working on a PRE-EXISTING Nagios server where there are several other existing plugins and checks running and working. Now I want to add another server there to check so I made the following modifications: First and foremost, I added a file to /usr/local/nagios/libexec named: check_equallogic.sh. The permissions are 755, the same as all others. I have chowned to nagios:nagios and in the listing it shows the Owner as Nagios. I then added a command to the commands.cfg file in \usr\local\nagios\etc\objects that shows the following: # 'check_equallogic' command definition define command{ command_name check_equallogic command_line $USER1$/check_equallogic -H $HOSTADDRESS$ -C $ARG1$ -t $ARG2$ $ARG3$ } Following this, I created a file named equallogic.cfg in the objects directory and it contains (more or less): define host{ use linux-server ; Inherit default values from a template host_name 172.16.50.11 ; The name we're giving to this device alias EqualLogic ; A longer name associated with the device address 172.16.50.11 ; IP address of the device contact_groups admins } Check Equallogic Information define service{ use generic-service host_name 172.16.50.11 service_description General Information check_command check_equallogic!public!info } After ensuring that permissions are okay for all files, I restart the nagios service, no errors. When I go into the WebGUI, I get the following errors AFTER the check runs: (Return code of 127 is out of bounds - plugin may be missing) Extra, probably unrelated problem Furthermore, when I log into the EquilLogic server, under Audit logs I get the following error: Level: AUDIT Time: 26/05/2014 3:59:13 PM Member: ps4100-1 Subsystem: agent Event ID: 22.7.1 SNMP packet validation failed, request received from 172.16.10.11 An snmpwalk receives a timeout, whereas others succeed. I will work on importing the MIBs tomorrow. The reason why I am mentioning it is because I want to make sure that it is only a MIB issue for the SNMP. If it is, then ignore this area. I am entirely unsure of what to do here.

    Read the article

  • How do Windows 7 encrypted files look like?

    - by Sean Farrell
    Ok this is kind of an odd question: How do Windows 7 (Home Premium) encrypted files look like "from the outside"? Now here is the story. An acquaintance of a freind of mine got a nasty virus / scareware. So I wiped out my PC technician cap and went to work on it. What I did was remove the drive from the laptop and put drive into my external drive bay. I scanned the drive and yes it was loaded with stuff. That basically cured the infection and I could start the system back up. To check if it cured the problem I wanted to see the system while running. There where two user accounts, on with a password and one without (both admin users !?!). So I logged into the unprotected user and cleaned up the residual issues, like proxy server to localhost in the browser config. Now I wanted to do the same for the password protected user. What I noticed that from my system and the unprotected user account the files of the protected user looked garbled. The files are something like 12 random alphanum chars, but the folders looked ok. Naive as was thought this might be how encrypted files looked "from the outside". (I never use Microsoft's own security features, so how would I know. TrueCrypt is one big blob.) Since the second user could not be reached, I though sod it and removed the password from the account. (That might have been a mistake, I know.) Now I did the same clean up tasks and all nice and fine; except for the files which where still "encrypted". So I looked into many Windows Encrypted Files recovery posts and not all hope is lost, since I should be able to extract the certificate and with the password regain access to the files. Also note that windows did "only" prompt me that removing the password would be insecure, not that access to encrypted files would be lost, like it is claimed in most recovery articles. Resetting the password did not help and I gave up for the night. The question that nagged me half of the last night was, what if the files are not encrypted, but the scare-ware encrypted / destroyed the files? I don't want to spend hours of work trying to recover files that are not recoverable. The ting is that the user does not remember turning it on and aren't the files marked in blue and the filename is readable? Many thanks for input from users who have more knowledge about WEF...

    Read the article

  • Alienware m15x (older model) BSOD investigation

    - by Crishu
    A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

    Read the article

  • How to install RAID drivers on already installed Windows 7?

    - by happysencha
    64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

    Read the article

  • Computer randomly reboots during "intensive activity".

    - by Reznor
    My friend has been playing games on his new build for some time now. However, lately, his computer will randomly reboot out of nowhere, so far only happening in game, and presumably only to happen in game as it happens nowhere else. This can happen in game during play or even in the options. Note, it isn't a crash or blue screen. It's just a normal reboot. This started today, I believe, and has only occured in two games: Dead Space and Stalker: Shadow of Chernobyl. He has played a handful of games before these, for about a week or so, without this problem. We theorized on two possibilities: Maybe something is overheating? Maybe the power supply is inadequate? These two were quickly dismissed, as all his components were operating at normal temperatures when he got back to his desktop from the reboot, and we all know these parts don't exactly cool down quickly, especially if they get hot enough to trigger a reboot. Besides, I know at-least my motherboard reports processor overheating at start-up, and requests I press f1 to continue into boot. The PSU one was dismissed too. He has an 850w power supply on a rig that was estimated to take only 720 some watts, that's with some overcompensating to be safe. He opened up his case to make sure nothing was seated wrong or in the way. All was fine, but he did notice a sticker on his video card. It had a giant barcode on it and some numbers. Now, I'm used to seeing these stickers, they're the warranty stickers, right, and removal voids the warranty? Yeah, well, we find it odd because this sticker is slapped right over the circuits of the video card, not on a block or anything. Is this normal? Should he remove it? Right now, I am concerned with the memory. Could that be at fault? Here are his specs: Windows 7 Home Premium, 64-Bit Intel i7 950 EVGA GeForce 570 GTX 4 GB DDR3 PC10666 dual-channel Corsair RAM Corsair 850w PSU Gigabyte GA-X58A-UD3R Western Digital 1 TB WD1001FALS

    Read the article

  • Delphi - Proper way to page though data.

    - by Brad
    I have a string list (TStrings) that has a couple thousand items in it. I need to process them in groups of 100. I basically want to know what the best way to do the loop is in Delphi. I'm hitting a brick wall when I'm trying to figure it out. Thanks unit Unit2; interface uses Windows, Messages, SysUtils, Variants, Classes, Graphics, Controls, Forms, Dialogs, StdCtrls; type TForm2 = class(TForm) Memo1: TMemo; Memo2: TMemo; Button1: TButton; procedure Button1Click(Sender: TObject); private { Private declarations } public { Public declarations } end; var Form2: TForm2; implementation Uses math; {$R *.dfm} procedure TForm2.Button1Click(Sender: TObject); var I:Integer; pages:Integer; str:string; begin pages:= ceil(memo1.Lines.Count/100) ; memo2.Lines.add('Total Pages: '+inttostr(pages)); memo2.Lines.add('Total Items: '+inttostr(memo1.Lines.Count)); // Should just do in batches of 100 VS entire list for I := 0 to memo1.lines.Count - 1 do begin if str '' then str:= str+#10+ memo1.Lines.Strings[i] else str:= memo1.Lines.Strings[i]; end; //I need to stop here every 100 items, then process the items. memo2.Lines.Add(str); end; end. Example form object Form2: TForm2 Left = 0 Top = 0 Caption = 'Form2' ClientHeight = 245 ClientWidth = 527 Color = clBtnFace Font.Charset = DEFAULT_CHARSET Font.Color = clWindowText Font.Height = -11 Font.Name = 'Tahoma' Font.Style = [] OldCreateOrder = False PixelsPerInch = 96 TextHeight = 13 object Memo1: TMemo Left = 16 Top = 8 Width = 209 Height = 175 Lines.Strings = ( '4xlt columbia thunder storm jacket' '5 things about thunder storms' 'a thunder storm with a lot of thunder ' 'and lighting sccreensaver' 'a thunder storm with a lot of thunder ' 'and lighting screensaver with no nag ' 'screens' 'all about thunder storms' 'all about thunderstorms for kids' 'amazing tornado videos and ' 'thunderstorm videos' 'are thunder storms louder in ohio?' 'bad thunder storms' 'bathing in thunder storm' 'best thunderstorm pictures' 'cartoon thunder storms' 'celtic thunder storm' 'central valley thunder storm' 'chicago thunderstorm pictures' 'cool thunderstorm pictures' 'current thunderstorm warnings' 'does thunder storms in december mean ' 'snow will be coming' 'facts about thunderstorms for kids' 'facts on thunderstorms for kids' 'fedex thunderstorm video' 'florida thunderstorms facts' 'free relaxing thunderstorm music' 'free soothing thunderstorm sounds ' 'online' 'free thunderstorm mp3' 'free thunderstorm mp3 download' 'free thunderstorm mp3 downloads' 'free thunderstorm mp3s' 'free thunderstorm music' 'free thunderstorm pictures' 'free thunderstorm sound effects' 'free thunderstorm sounds' 'free thunderstorm sounds cd' 'free thunderstorm sounds mp3' 'free thunderstorm sounds online' 'free thunderstorm soundscape' 'free thunderstorm video' 'free thunderstorm video download' 'free thunderstorm videos' 'god of storm and thunder' 'horses storm thunder rain' 'how do thunder storms form' 'how far away is a thunder storm' 'how long do thunder storms last' 'ice cube in a thunder storm' 'indoor thunderstorm safety tips' 'information about thunderstorms for kids' 'interesting thunderstorm facts' 'is it dangerous to shower during thunder ' 'storm' 'is there frequently thunder during snow ' 'storms' 'isolated thunderstorms' 'it'#39's just a thunder storm baby there is ' 'nothing you should fear lyrics' 'lightning & thunder storm safety' 'lightning and thunderstorm facts' 'lightning and thunderstorms facts' 'lightning and thunderstorms for kids' 'listen to thunderstorm sounds online' 'mississauga thunder storm' 'nature sounds free mp3 thunder storm' 'only about thunderstorms facts' 'original storm deep thunderstick' 'phone use during thunder storms' 'pictures of thunderstorms' 'pocono thunder storm' 'posters of thunder storms' 'power rangers ninja storm' 'power rangers thunder storm' 'power rangers thunder storm cast' 'power rangers thunder storm games' 'power rangers thunder storm morphers' 'power rangers thunder storm part 1' 'power rangers thunder storm part 2' 'power rangers thunderstorm' 'power rangers thunderstorm cannon' 'power rangers thunderstorm deluxe ' 'megazord' 'power rangers thunderstorm games' 'power rangers thunderstorm megazord' 'power rangers thunderstorm part 2' 'power rangers thunderstorm pictures' 'power rnager ninja storm thunder staff' 'powerful thunder and lightning storms' 'precambrian thunder storms' 'rain thunderstorm mp3' 'rain thunderstorm pictures' 'relaxing thunderstorm music' 'reminds me of ohio river thunder lighten ' 'storms' 'sacramento thunder storm' 'safety tips for when your caught in a ' 'thunder storm' 'scattered thunderstorms' 'schemer puts his head in the thunder ' 'storm' 'sedative thunder storm' 'server thunder storms' 'severe supercell thunderstorm pictures' 'severe thunder storm pictures' 'severe thunder storms' 'severe thunderstorm facts' 'severe thunderstorm pictures' 'severe thunderstorm pictures hail' 'severe thunderstorm pictures in alberta' 'severe thunderstorm pictures tornado' 'severe thunderstorm safety' 'severe thunderstorm safety tips' 'severe thunderstorm videos' 'severe thunderstorm warning' 'severe thunderstorm warning los ' 'angeles' 'severe thunderstorm warning signs' 'severe thunderstorm warnings' 'severe thunderstorms' 'severe thunderstorms facts' 'shakespeare use thunder storm for ' 'cosmic disorder julius caesar' 'soothing thunderstorm sounds online' 'sound effects of severe thunder storm' 'sound of rain storm finger snapping ' 'thunder chorus' 'split thunder storm' 'storm 3d thunder power' 'storm dark thunder' 'storm dark thunder bowling ball' 'storm dark thunder bowling ball sale' 'storm dark thunder for sale' 'storm dark thunder pearl' 'storm dark thunder pearl bowling ball' 'storm dark thunder review' 'storm dark thunder shirt' 'storm dark thunderball' 'storm deep thunder' 'storm deep thunder 11' 'storm deep thunder 15' 'storm deep thunder 15 lure' 'storm deep thunder 2' 'storm deep thunder lures' 'storm deep thunderstick' 'storm deep thunderstick crankbaits' 'storm deep thunderstick dts09' 'storm deep thunderstick jr' 'storm deep thunderstick lures' 'storm deep thundersticks' 'storm rolling thunder 3 ball roller' 'storm rolling thunder bowling bag' 'storm rolling thunder three ball bowling ' 'bag' 'storm shallow thunder' 'storm shallow thunder 15' 'storm thunder claw' 'storm thunder craw' 'storm watches thunder' 'storms with constant lightning and ' 'thunder non-stop' 'supercell thunder storms' 'supercell thunderstorm pictures' 'supercell thunderstorms' 'swimming pools thunder storms' 'tampa + lightning strikes + thunder ' 'storms' 'texas thunderstorm pictures' 'texas thunderstorm warnings' 'thunder and lightning storm' 'thunder and lighting storms' 'thunder and lightning storms' 'thunder bay snow storm video' 'thunder storm' 'thunder storm and windmill' 'thunder storm cd' 'thunder storm cloud' 'thunder storm clouds' 'thunder storm dog peppermint oil' 'thunder storm in winter' 'thunder storm in winter and weather ' 'prediction' 'thunder storm lx-3 & road blaster psx ' 'download' 'thunder storm occurances' 'thunder storm photos' 'thunder storm poems' 'thunder storm safety' 'thunder storm sign' 'thunder storm sounds' 'thunder storms' 'thunder storms and deaths' 'thunder storms and ilghting' 'thunder storms and lighting' 'thunder storms cd' 'thunder storms in the arctic arctic ' 'weather' 'thunder storms in winter' 'thunder storms on you tub' 'thunder storms pics' 'thunder storms with rain' 'thunderstorm' 'thunderstorm backgrounds' 'thunderstorm capital' 'thunderstorm capital 2008 dorfman' 'thunderstorm capital in boston' 'thunderstorm capital llc' 'thunderstorm capital of canada' 'thunderstorm capital of the us' 'thunderstorm capital of the world' 'thunderstorm facts' 'thunderstorm facts for kids' 'thunderstorm facts hail' 'thunderstorm facts tornadoes' 'thunderstorm mp3' 'thunderstorm mp3 download' 'thunderstorm mp3 download free' 'thunderstorm mp3 downloads' 'thunderstorm mp3 downloads free' 'thunderstorm mp3 files' 'thunderstorm mp3 free' 'thunderstorm mp3 free download' 'thunderstorm mp3 free downloads' 'thunderstorm mp3 torrent' 'thunderstorm mp3s' 'thunderstorm music' 'thunderstorm music cd' 'thunderstorm music downloads' 'thunderstorm music free' 'thunderstorm music playlists' 'thunderstorm music rain' 'thunderstorm pics' 'thunderstorm pictures' 'thunderstorm pictures for kids' 'thunderstorm safety' 'thunderstorm safety for kids' 'thunderstorm safety precautions' 'thunderstorm safety procedures' 'thunderstorm safety rules' 'thunderstorm safety tips' 'thunderstorm safety tips for kids' 'thunderstorm safety tips shelter' 'thunderstorm safety tips trees' 'thunderstorm sound effects' 'thunderstorm sound effects cd' 'thunderstorm sound effects download' 'thunderstorm sound effects free' 'thunderstorm sound effects free ' 'download' 'thunderstorm sound effects free music ' 'feature audio' 'thunderstorm sound effects mp3' 'thunderstorm sound effects rain' 'thunderstorm sounds' 'thunderstorm sounds cd' 'thunderstorm sounds download' 'thunderstorm sounds for sleep' 'thunderstorm sounds for sleeping' 'thunderstorm sounds free' 'thunderstorm sounds free download' 'thunderstorm sounds free downloads' 'thunderstorm sounds mp3' 'thunderstorm sounds mp3 download' 'thunderstorm sounds mp3 free' 'thunderstorm sounds online' 'thunderstorm sounds online for free' 'thunderstorm sounds online free' 'thunderstorm sounds sleep' 'thunderstorm sounds streaming' 'thunderstorm sounds torrent' 'thunderstorm soundscape' 'thunderstorm soundscapes' 'thunderstorm video' 'thunderstorm video clips' 'thunderstorm video download' 'thunderstorm video downloads' 'thunderstorm videos' 'thunderstorm videos for kids' 'thunderstorm videos lightning' 'thunderstorm videos online' 'thunderstorm wallpaper' 'thunderstorm warning' 'thunderstorm warning brisbane' 'thunderstorm warning definition' 'thunderstorm warning los angeles' 'thunderstorm warning san diego' 'thunderstorm warning san mateo county' 'thunderstorm warning santa barbara' 'thunderstorm warning santa clara' 'thunderstorm warning santa clara ' 'county' 'thunderstorm warning signal' 'thunderstorm warning signs' 'thunderstorm warning vs watch' 'thunderstorm warnings' 'thunderstorm warnings and watches' 'thunderstorm warnings for nj' 'thunderstorm warnings qld' 'thunderstorms' 'thunderstorms facts' 'thunderstorms facts for kids' 'thunderstorms for kids' 'tornados and thunder storms animated' 'understanding thunderstorms for kids' 'watch thunderstorm videos' 'weather underground forecast ' 'thunderstorms' 'what causes thunder storms' 'what is a thunder storm' 'where d thunder storms occur') TabOrder = 0 end object Memo2: TMemo Left = 240 Top = 8 Width = 265 Height = 129 Lines.Strings = ( 'Memo2') TabOrder = 1 end object Button1: TButton Left = 384 Top = 184 Width = 75 Height = 25 Caption = 'Button1' TabOrder = 2 OnClick = Button1Click end end

    Read the article

  • Why keylistener is not working here?

    - by swift
    i have implemented keylistener interface and implemented all the needed methods but when i press the key nothing happens here, why? package swing; import java.awt.Color; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Graphics2D; import java.awt.GridLayout; import java.awt.Point; import java.awt.RenderingHints; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.awt.event.KeyEvent; import java.awt.event.KeyListener; import java.awt.event.MouseEvent; import java.awt.event.MouseListener; import java.awt.event.MouseMotionListener; import java.awt.event.WindowAdapter; import java.awt.event.WindowEvent; import java.awt.image.BufferedImage; import javax.swing.BorderFactory; import javax.swing.BoxLayout; import javax.swing.ImageIcon; import javax.swing.JButton; import javax.swing.JFrame; import javax.swing.JLayeredPane; import javax.swing.JPanel; import javax.swing.JTextArea; class Paper extends JPanel implements MouseListener,MouseMotionListener,ActionListener,KeyListener { static BufferedImage image; String shape; Color color=Color.black; Point start; Point end; Point mp; Button elipse=new Button("elipse"); int x[]=new int[50]; int y[]=new int[50]; Button rectangle=new Button("rect"); Button line=new Button("line"); Button roundrect=new Button("roundrect"); Button polygon=new Button("poly"); Button text=new Button("text"); ImageIcon erasericon=new ImageIcon("images/eraser.gif"); JButton erase=new JButton(erasericon); JButton[] colourbutton=new JButton[9]; String selected; Point label; String key; int ex,ey;//eraser //DatagramSocket dataSocket; JButton button = new JButton("test"); JLayeredPane layerpane; Point p=new Point(); int w,h; public Paper() { JFrame frame=new JFrame("Whiteboard"); frame.setVisible(true); frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); frame.setSize(640, 480); frame.setBackground(Color.black); layerpane=frame.getLayeredPane(); setWidth(539,444); setBounds(69,0,555,444); layerpane.add(this,new Integer(2)); layerpane.add(this.addButtons(),new Integer(0)); setLayout(null); setOpaque(false); addMouseListener(this); addMouseMotionListener(this); setFocusable(true); addKeyListener(this); System.out.println(isFocusable()); setBorder(BorderFactory.createLineBorder(Color.black)); } public void paintComponent(Graphics g) { try { super.paintComponent(g); g.drawImage(image, 0, 0, this); Graphics2D g2 = (Graphics2D)g; if(color!=null) g2.setPaint(color); if(start!=null && end!=null) { if(selected==("elipse")) g2.drawOval(start.x, start.y,(end.x-start.x),(end.y-start.y)); else if(selected==("rect")) g2.drawRect(start.x, start.y, (end.x-start.x),(end.y-start.y)); else if(selected==("rrect")) g2.drawRoundRect(start.x, start.y, (end.x-start.x),(end.y-start.y),11,11); else if(selected==("line")) g2.drawLine(start.x,start.y,end.x,end.y); else if(selected==("poly")) g2.drawPolygon(x,y,2); } } catch(Exception e) {} } //Function to draw the shape on image public void draw() { Graphics2D g2 = image.createGraphics(); g2.setPaint(color); if(start!=null && end!=null) { if(selected=="line") g2.drawLine(start.x, start.y, end.x, end.y); else if(selected=="elipse") g2.drawOval(start.x, start.y, (end.x-start.x),(end.y-start.y)); else if(selected=="rect") g2.drawRect(start.x, start.y, (end.x-start.x),(end.y-start.y)); else if(selected==("rrect")) g2.drawRoundRect(start.x, start.y, (end.x-start.x),(end.y-start.y),11,11); else if(selected==("poly")) g2.drawPolygon(x,y,2); } if(label!=null) { JTextArea textarea=new JTextArea(); if(selected==("text")) { textarea.setBounds(label.x, label.y, 50, 50); textarea.setMaximumSize(new Dimension(100,100)); textarea.setBackground(new Color(237,237,237)); add(textarea); g2.drawString("key",label.x,label.y); } } start=null; repaint(); g2.dispose(); } public void text() { System.out.println(label); } //Function which provides the erase functionality public void erase() { Graphics2D pic=(Graphics2D) image.getGraphics(); Color erasecolor=new Color(237,237,237); pic.setPaint(erasecolor); if(start!=null) pic.fillRect(start.x, start.y, 10, 10); } //To set the size of the image public void setWidth(int x,int y) { System.out.println("("+x+","+y+")"); w=x; h=y; image = new BufferedImage(w, h, BufferedImage.TYPE_INT_ARGB); } //Function to add buttons into the panel, calling this function returns a panel public JPanel addButtons() { JPanel buttonpanel=new JPanel(); buttonpanel.setMaximumSize(new Dimension(70,70)); JPanel shape=new JPanel(); JPanel colourbox=new JPanel(); shape.setLayout(new GridLayout(4,2)); shape.setMaximumSize(new Dimension(70,140)); colourbox.setLayout(new GridLayout(3,3)); colourbox.setMaximumSize(new Dimension(70,70)); buttonpanel.setLayout(new BoxLayout(buttonpanel,BoxLayout.Y_AXIS)); elipse.addActionListener(this); elipse.setToolTipText("Elipse"); rectangle.addActionListener(this); rectangle.setToolTipText("Rectangle"); line.addActionListener( this); line.setToolTipText("Line"); erase.addActionListener(this); erase.setToolTipText("Eraser"); roundrect.addActionListener(this); roundrect.setToolTipText("Round rect"); polygon.addActionListener(this); polygon.setToolTipText("Polygon"); text.addActionListener(this); text.setToolTipText("Text"); shape.add(elipse); shape.add(rectangle); shape.add(line); shape.add(erase); shape.add(roundrect); shape.add(polygon); shape.add(text); buttonpanel.add(shape); for(int i=0;i<9;i++) { colourbutton[i]=new JButton(); colourbox.add(colourbutton[i]); if(i==0) colourbutton[0].setBackground(Color.black); else if(i==1) colourbutton[1].setBackground(Color.white); else if(i==2) colourbutton[2].setBackground(Color.red); else if(i==3) colourbutton[3].setBackground(Color.orange); else if(i==4) colourbutton[4].setBackground(Color.blue); else if(i==5) colourbutton[5].setBackground(Color.green); else if(i==6) colourbutton[6].setBackground(Color.pink); else if(i==7) colourbutton[7].setBackground(Color.magenta); else if(i==8) colourbutton[8].setBackground(Color.cyan); colourbutton[i].addActionListener(this); } buttonpanel.add(colourbox); buttonpanel.setBounds(0, 0, 70, 210); return buttonpanel; } public void mouseClicked(MouseEvent e) { if(selected=="text") { label=new Point(); label=e.getPoint(); draw(); } } @Override public void mouseEntered(MouseEvent arg0) { } public void mouseExited(MouseEvent arg0) { } public void mousePressed(MouseEvent e) { if(selected=="line"||selected=="erase"||selected=="text") { start=e.getPoint(); } else if(selected=="elipse"||selected=="rect"||selected=="rrect") { mp = e.getPoint(); } else if(selected=="poly") { x[0]=e.getX(); y[0]=e.getY(); } } public void mouseReleased(MouseEvent e) { if(start!=null) { if(selected=="line") { end=e.getPoint(); } else if(selected=="elipse"||selected=="rect"||selected=="rrect") { end.x = Math.max(mp.x,e.getX()); end.y = Math.max(mp.y,e.getY()); } else if(selected=="poly") { x[1]=e.getX(); y[1]=e.getY(); } draw(); } } public void mouseDragged(MouseEvent e) { if(end==null) end = new Point(); if(start==null) start = new Point(); if(selected=="line") { end=e.getPoint(); } else if(selected=="erase") { start=e.getPoint(); erase(); } else if(selected=="elipse"||selected=="rect"||selected=="rrect") { start.x = Math.min(mp.x,e.getX()); start.y = Math.min(mp.y,e.getY()); end.x = Math.max(mp.x,e.getX()); end.y = Math.max(mp.y,e.getY()); } else if(selected=="poly") { x[1]=e.getX(); y[1]=e.getY(); } repaint(); } public void mouseMoved(MouseEvent arg0) {} public void actionPerformed(ActionEvent e) { if(e.getSource()==elipse) selected="elipse"; else if(e.getSource()==line) selected="line"; else if(e.getSource()==rectangle) selected="rect"; else if(e.getSource()==erase) { selected="erase"; System.out.println(selected); erase(); } else if(e.getSource()==roundrect) selected="rrect"; else if(e.getSource()==polygon) selected="poly"; else if(e.getSource()==text) selected="text"; if(e.getSource()==colourbutton[0]) color=Color.black; else if(e.getSource()==colourbutton[1]) color=Color.white; else if(e.getSource()==colourbutton[2]) color=Color.red; else if(e.getSource()==colourbutton[3]) color=Color.orange; else if(e.getSource()==colourbutton[4]) color=Color.blue; else if(e.getSource()==colourbutton[5]) color=Color.green; else if(e.getSource()==colourbutton[6]) color=Color.pink; else if(e.getSource()==colourbutton[7]) color=Color.magenta; else if(e.getSource()==colourbutton[8]) color=Color.cyan; } @Override public void keyPressed(KeyEvent e) { System.out.println("pressed"); } @Override public void keyReleased(KeyEvent e) { System.out.println("key released"); } @Override public void keyTyped(KeyEvent e) { System.out.println("Typed"); } public static void main(String[] a) { new Paper(); } } class Button extends JButton { String name; public Button(String name) { this.name=name; } public void paintComponent(Graphics g) { super.paintComponent(g); Graphics2D g2 = (Graphics2D)g; g2.setRenderingHint(RenderingHints.KEY_ANTIALIASING, RenderingHints.VALUE_ANTIALIAS_ON); //g2.setStroke(new BasicStroke(1.2f)); if (name == "line") g.drawLine(5,5,30,30); if (name == "elipse") g.drawOval(5,7,25,20); if (name== "rect") g.drawRect(5,5,25,23); if (name== "roundrect") g.drawRoundRect(5,5,25,23,10,10); int a[]=new int[]{20,9,20,23,20}; int b[]=new int[]{9,23,25,20,9}; if (name== "poly") g.drawPolyline(a, b, 5); if (name== "text") g.drawString("Text",5, 22); } }

    Read the article

  • How do I ensure that a JPanel Shrinks when the parent frame is resized?

    - by dah
    I have a basic notes panel that I'm looking to shrink the width of when the parent jframe is resized but it isn't happening. I'm using nested gridbaglayouts. package com.protocase.notes.views; import com.protocase.notes.controller.NotesController; import com.protocase.notes.model.Subject; import com.protocase.notes.model.Note; import com.protocase.notes.model.database.PMSNotesAdapter; import java.awt.Color; import java.awt.GridBagConstraints; import java.awt.GridBagLayout; import javax.swing.BorderFactory; import javax.swing.JButton; import javax.swing.JLabel; import javax.swing.JPanel; import javax.swing.JScrollPane; /** * @author DavidH */ public class NotesViewer extends JPanel { // <editor-fold defaultstate="collapsed" desc="Attributes"> private Subject subject; private NotesController controller; //</editor-fold> // <editor-fold defaultstate="collapsed" desc="Getters N' Setters"> /** * Gets back the current subject. * @return */ public Subject getSubject() { return subject; } public NotesController getController() { return controller; } public void setController(NotesController controller) { this.controller = controller; } /** * Should clear the panel of the current subject and load the details for * the other object. * @param subject */ public void setSubject(Subject subject) { this.subject = subject; } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="Constructor"> /** * -- Sets up a note viewer with a subject and a controller. Likely this * would be the constructor used if you were passing off from another * NoteViewer or something else that used a notes adapter or controller. * @param subject * @param controller */ public NotesViewer(Subject subject, NotesController controller) { this.subject = subject; this.controller = controller; initComponents(); } /** * -- Sets up a note view with a subject and creates a new controller. This * would be the constructor typically chosen if choosing notes was * infrequent and only one or two notes needs to be displayed. * @param subject */ public NotesViewer(Subject subject) { this(subject, new NotesController(new PMSNotesAdapter())); } /** * -- Sets up a note view without a subject and creates a new controller. * This would be for a note viewer without any notes, perhaps populating * as you choose values in another form. * @param subject */ public NotesViewer() { this(null); } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="initComponents()"> /** * Sets up the view for the NotesViewer */ private void initComponents() { // -- Make a new panel for the header JPanel panel = new JPanel(); panel.setLayout(new GridBagLayout()); GridBagConstraints c = new GridBagConstraints(); c.gridx = 0; c.fill = GridBagConstraints.HORIZONTAL; c.gridy = 0; c.weightx = .5; //c.anchor = GridBagConstraints.NORTHWEST; JLabel label = new JLabel("Viewing Notes for [Subject]"); label.setAlignmentX(JLabel.LEFT_ALIGNMENT); label.setBorder(BorderFactory.createLineBorder(Color.YELLOW)); panel.add(label); JButton newNoteButton = new JButton("New"); c = new GridBagConstraints(); // c.fill = GridBagConstraints.HORIZONTAL; c.gridx = 1; c.gridy = 0; c.weightx = .5; c.anchor = GridBagConstraints.EAST; panel.add(newNoteButton, c); // -- NotePanels c = new GridBagConstraints(); c.fill = GridBagConstraints.HORIZONTAL; c.weightx = 1; c.weighty = 1; c.gridx = 0; c.gridwidth = 2; int y = 1; for (Note n : subject.getNotes()) { c.gridy = y++; panel.add(new NotesPanel(n, controller), c); } this.setLayout(new GridBagLayout()); GridBagConstraints pc = new GridBagConstraints(); pc.gridx = 0; pc.gridy = 0; pc.weightx = 1; pc.weighty = 1; pc.fill = GridBagConstraints.BOTH; panel.setBackground(Color.blue); JScrollPane scroll = new JScrollPane(); scroll.setViewportView(panel); //scroll.setHorizontalScrollBarPolicy(JScrollPane.HORIZONTAL_SCROLLBAR_NEVER); this.add(scroll, pc); //this.add(panel, pc); // -- Add it all to the layout } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="private methods"> //</editor-fold> } package com.protocase.notes.views; import com.protocase.notes.controller.NotesController; import com.protocase.notes.model.Note; import java.awt.CardLayout; import java.awt.Color; import java.awt.Component; import java.awt.Dimension; import java.awt.GridBagConstraints; import java.awt.GridBagLayout; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.text.DateFormat; import java.text.SimpleDateFormat; import javax.swing.BorderFactory; import javax.swing.JButton; import javax.swing.JLabel; import javax.swing.JPanel; import javax.swing.JScrollPane; import javax.swing.JTextArea; import javax.swing.JTextField; import javax.swing.border.BevelBorder; import javax.swing.border.Border; import javax.swing.border.MatteBorder; /** * @author dah01 */ public class NotesPanel extends JPanel { // <editor-fold defaultstate="collapsed" desc="Attributes"> private Note note; private NotesController controller; private CardLayout cardLayout; private JTextArea viewTextArea; private JTextArea editTextArea; //</editor-fold> // <editor-fold defaultstate="collapsed" desc="Getters N' Setters"> public NotesController getController() { return controller; } public void setController(NotesController controller) { this.controller = controller; } public Note getNote() { return note; } public void setNote(Note note) { this.note = note; } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="Constructor"> /** * Sets up a note panel that shows everything about the note. * @param note */ public NotesPanel(Note note, NotesController controller) { this.note = note; cardLayout = new CardLayout(); this.setLayout(cardLayout); // -- Setup the layout manager. this.setBackground(new Color(199, 187, 192)); this.setBorder(new BevelBorder(BevelBorder.RAISED)); // -- ViewPanel this.add("ViewPanel", initViewPanel()); this.add("EditPanel", initEditPanel()); } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="EditPanel"> private JPanel initEditPanel() { JPanel editPanel = new JPanel(); editPanel.setLayout(new GridBagLayout()); GridBagConstraints c = new GridBagConstraints(); c.fill = GridBagConstraints.HORIZONTAL; c.gridy = 0; c.weightx = 1; c.weighty = 0.3; editPanel.add(initCreatorLabel(), c); c.gridy++; editPanel.add(initEditTextScroll(), c); c.gridy++; c.anchor = GridBagConstraints.WEST; c.fill = GridBagConstraints.NONE; editPanel.add(initEditorLabel(), c); c.gridx++; c.anchor = GridBagConstraints.EAST; editPanel.add(initSaveButton(), c); return editPanel; } private JScrollPane initEditTextScroll() { this.editTextArea = new JTextArea(note.getContents()); editTextArea.setLineWrap(true); editTextArea.setWrapStyleWord(true); JScrollPane scrollPane = new JScrollPane(editTextArea); scrollPane.setAlignmentX(JScrollPane.LEFT_ALIGNMENT); Border b = scrollPane.getViewportBorder(); MatteBorder mb = BorderFactory.createMatteBorder(2, 2, 2, 2, Color.BLUE); scrollPane.setBorder(mb); return scrollPane; } private JButton initSaveButton() { final CardLayout l = this.cardLayout; final JPanel p = this; final NotesController c = this.controller; final Note n = this.note; final JTextArea noteText = this.viewTextArea; final JTextArea textToSubmit = this.editTextArea; ActionListener al = new ActionListener() { @Override public void actionPerformed(ActionEvent e) { //controller.saveNote(n); noteText.setText(textToSubmit.getText()); l.next(p); } }; JButton saveButton = new JButton("Save"); saveButton.addActionListener(al); saveButton.setPreferredSize(new Dimension(62, 26)); return saveButton; } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="ViewPanel"> private JPanel initViewPanel() { JPanel viewPanel = new JPanel(); viewPanel.setLayout(new GridBagLayout()); GridBagConstraints c = new GridBagConstraints(); c.fill = GridBagConstraints.HORIZONTAL ; c.gridy = 0; c.weightx = 1; c.weighty = 0.3; viewPanel.add(initCreatorLabel(), c); c.gridy++; viewPanel.add(this.initNoteTextArea(), c); c.fill = GridBagConstraints.NONE; c.anchor = GridBagConstraints.WEST; c.gridy++; viewPanel.add(initEditorLabel(), c); c.gridx++; c.anchor = GridBagConstraints.EAST; viewPanel.add(initEditButton(), c); return viewPanel; } private JLabel initCreatorLabel() { DateFormat formatter = new SimpleDateFormat("yyyy-MM-dd"); if (note != null) { String noteBy = "Note by " + note.getCreator(); String noteCreated = formatter.format(note.getDateCreated()); JLabel creatorLabel = new JLabel(noteBy + " @ " + noteCreated); creatorLabel.setAlignmentX(JLabel.LEFT_ALIGNMENT); return creatorLabel; } else { System.out.println("NOTE IS NULL"); return null; } } private JScrollPane initNoteTextArea() { // -- Setup the notes area. this.viewTextArea = new JTextArea(note.getContents()); viewTextArea.setEditable(false); viewTextArea.setLineWrap(true); viewTextArea.setWrapStyleWord(true); JScrollPane scrollPane = new JScrollPane(viewTextArea); scrollPane.setAlignmentX(JScrollPane.LEFT_ALIGNMENT); return scrollPane; } private JLabel initEditorLabel() { // -- Setup the edited by label. JLabel editorLabel = new JLabel(" -- Last edited by " + note.getLastEdited() + " at " + note.getDateModified()); editorLabel.setAlignmentX(Component.LEFT_ALIGNMENT); return editorLabel; } private JButton initEditButton() { final CardLayout l = this.cardLayout; final JPanel p = this; ActionListener ar = new ActionListener() { @Override public void actionPerformed(ActionEvent e) { l.next(p); } }; JButton editButton = new JButton("Edit"); editButton.setPreferredSize(new Dimension(62,26)); editButton.addActionListener(ar); return editButton; } //</editor-fold> // <editor-fold defaultstate="collapsed" desc="Grow Width When Resized"> @Override public Dimension getPreferredSize() { int fw = this.getParent().getSize().width; int fh = super.getPreferredSize().height; return new Dimension(fw,fh); } //</editor-fold> }

    Read the article

  • Add Zune Desktop Player to Windows 7 Media Center

    - by DigitalGeekery
    Are you a Zune owner who prefers the Zune player for media playback? Today we’ll show you how to integrate the Zune player with WMC using Media Center Studio. You’ll need to download Media Center Studio and the Zune Desktop player software. (See download links below) Also, make sure you have Media Center closed. Some of the actions in Media Center Studio cannot be performed while WMC is open. Open Media Center Studio and click on the Start Menu tab at the top of the application.   Click the Application button. Here we will create an Entry Point for the Zune player so that we can add it to Media Center. Type in a name for your entry point in the title text box. This is the name that will appear under the tile when added to the Media Center start menu. Next, type in the path to the Zune player. By default this should be C:\Program Files\Zune\Zune.exe. Note: Be sure to use the original path, not a link to the desktop icon.   The Active image is the image that will appear on the tile in Media Center. If you wish to change the default image, click the Browse button and select a different image. Select Stop the currently playing media from the When launched do the following: dropdown list.  Otherwise, if you open Zune player from WMC while playing another form of media, that media will continue to play in the background.   Now we will choose a keystroke to use to exit the Zune player software and return to Media Center. Click on the the green plus (+) button. When prompted, press a key to use to the close the Zune player. Note: This may also work with your Media Center remote. You may want to set a keyboard keystroke as well as a button on your remote to close the program. You may not be able to set certain remote buttons to close the application. We found that the back arrow button worked well. You can also choose a keystroke to kill the program if desired. Be sure to save your work before exiting by clicking the Save button on the Home tab.   Next, select the Start Menu tab and click on the next to Entry points to reveal the available entry points. Find the Zune player tile in the Entry points area. We want to drag the tile out onto one of the menu strips on the start menu. We will drag ours onto the Extras Library strip. When you begin to drag the tile, green plus (+) signs will appear in between the tiles. When you’ve dragged the tile over any of the green plus signs, the  red “Move” label will turn to a blue “Move to” label. Now you can drop the tile into position. Save your changes and then close Media Center Studio. When you open Media Center, you should see your Zune tile on the start menu. When you select the Zune tile in WMC, Media Center will be minimized and Zune player will be launched. Now you can enjoy your media through the Zune player. When you close Zune player with the previously assigned keystroke or by clicking the “X” at the top right, Windows Media Center will be re-opened. Conclusion We found the Zune player worked with two different Media Center remotes that we tested. It was a times a little tricky at times to tell where you were when navigating through the Zune software with a remote, but it did work. In addition to managing your music, the Zune player is a nice way to add podcasts to your Media Center setup. We should also mention that you don’t need to actually own a Zune to install and use the Zune player software. Media Center Studio works on both Vista and Windows 7. We covered Media Center Studio a bit more in depth in a previous post on customizing the Windows Media Center start menu. Are you new to Zune player? Familiarize yourself a bit more by checking out some of our earlier posts like how to update your Zune player, and experiencing your music a whole new way with Zune for PC.   Downloads Zune Desktop Player download Media Center Studio download Similar Articles Productive Geek Tips How To Rip a Music CD in Windows 7 Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Fixing When Windows Media Player Library Won’t Let You Add FilesBuilt-in Quick Launch Hotkeys in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation" Enable or Disable the Task Manager Using TaskMgrED Explorer++ is a Worthy Windows Explorer Alternative Error Goblin Explains Windows Error Codes Twelve must-have Google Chrome plugins

    Read the article

  • Add Background Images and Themes to Windows 7 Media Center

    - by DigitalGeekery
    Are you tired of the same Windows Media Center look and feel? Today we’ll show you how change the background and apply themes to WMC. Changing the Basic Color Scheme in WMC There are a couple of very basic color scheme options built in to Windows 7 Media Center. From the WMC Start Menu, select Settings on the Tasks strip and then select General. On the General settings screen select Visual and Sound Effects.   Under Color scheme you’ll find options for Windows Media Center standard, High contrast white, and High contrast black. Simply select a color scheme and click Save before exiting.   If you have used Media Center before you are familiar with the standard blue default theme. There is also the high contrast white. And, the high contrast black. Changing the Background Image with Media Center Studio Themes and custom backgrounds need to be added with the third-party software, Media Center Studio. You can find the download link at the end of this article. You can use your own high resolution photo, or download one from the Internet. For best results, you’ll want to find an image that meets or exceeds the resolution of your monitor. Also, using a darker colored background image is ideal as it should contrast better with the lighter colored text of the start menu. Once you’ve downloaded and installed Media Center Studio (link below), open the application select the Home tab on the ribbon and make sure you are on the Themes tab below. Click New. Select Biography from the left pane and type in a name for your new theme.   Next, click on the triangle next to Images to expand the list below. You’ll want to browse to Images > Common > Background. You should see a list of PNG image files located below Background. We will want to swap out the COMMON.ANIMATED.BACKGROUND.PNG and the COMMON.BACKGROUND.PNG images. Select COMMON.ANIMATED.BACKGROUND.PNG and click on the Browse button on the right.   Browse for your photo and click Open. Your selected image will appear on the left pane. Now, do the same for the COMMON.BACKGROUND.PNG. When finished, select the Home tab on the ribbon at the top and click Save.   Now switch to the Themes tab on the ribbon and the Themes tab below. (There are two Themes tabs which can be a bit confusing). Select your theme on the right pane and click Apply. Note: You won’t see the image backgrounds displayed. Your theme will be applied to Media Center. Close out of Media Center Studio and open Windows Media Center to check out your new background.   You can load multiple backgrounds images and switch them periodically as your mood changes. You might like to find a nice background featuring your favorite movie or TV show.   Perhaps you can even find a background of your favorite sports team.   Installing Themes with Media Center Studio Theme7MC has made available a small group of Media Center Studio Theme packs that are simple to download and install. You can find the download link below. Note: Before installing a theme, turn off any extenders and close Windows Media Center. Download any (or all) of the Theme7MC theme packages to your Media Center PC. Open Media Center Studio, select the Themes tab (the one at the top) and click Import Theme.   Browse for the theme you wish to import and click Open. Select your theme from the themes pane and click Apply. Media Center Studio will proceed to apply your theme. You should then see your new theme appear under Current theme on the left theme pane. Close out of Media Center Studio. Open Media Center and enjoy your new theme. Conclusion Media Center Studio runs on Windows 7 or Vista and gives users a solution for personalizing their Media Center backgrounds. It is a Beta application, however, so it still has a few bugs. Currently, there are only a handful of themes available at Themes7MC, but what they have is pretty slick. If you’d like to further customize the look of Media Center, check out our previous article on how to customize the Media Center start menu with Media Center Studio. Downloads Media Center Studio Theme7MC Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)How To Rip a Music CD in Windows 7 Media CenterAutomatically Mount and View ISO files in Windows 7 Media CenterSchedule Updates for Windows Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox) Backup Outlook 2010 Daily Motivator (Firefox) FetchMp3 Can Download Videos & Convert Them to Mp3

    Read the article

  • Diagnose PC Hardware Problems with an Ubuntu Live CD

    - by Trevor Bekolay
    So your PC randomly shuts down or gives you the blue screen of death, but you can’t figure out what’s wrong. The problem could be bad memory or hardware related, and thankfully the Ubuntu Live CD has some tools to help you figure it out. Test your RAM with memtest86+ RAM problems are difficult to diagnose—they can range from annoying program crashes, or crippling reboot loops. Even if you’re not having problems, when you install new RAM it’s a good idea to thoroughly test it. The Ubuntu Live CD includes a tool called Memtest86+ that will do just that—test your computer’s RAM! Unlike many of the Live CD tools that we’ve looked at so far, Memtest86+ has to be run outside of a graphical Ubuntu session. Fortunately, it only takes a few keystrokes. Note: If you used UNetbootin to create an Ubuntu flash drive, then memtest86+ will not be available. We recommend using the Universal USB Installer from Pendrivelinux instead (persistence is possible with Universal USB Installer, but not mandatory). Boot up your computer with a Ubuntu Live CD or USB drive. You will be greeted with this screen: Use the down arrow key to select the Test memory option and hit Enter. Memtest86+ will immediately start testing your RAM. If you suspect that a certain part of memory is the problem, you can select certain portions of memory by pressing “c” and changing that option. You can also select specific tests to run. However, the default settings of Memtest86+ will exhaustively test your memory, so we recommend leaving the settings alone. Memtest86+ will run a variety of tests that can take some time to complete, so start it running before you go to bed to give it adequate time. Test your CPU with cpuburn Random shutdowns – especially when doing computationally intensive tasks – can be a sign of a faulty CPU, power supply, or cooling system. A utility called cpuburn can help you determine if one of these pieces of hardware is the problem. Note: cpuburn is designed to stress test your computer – it will run it fast and cause the CPU to heat up, which may exacerbate small problems that otherwise would be minor. It is a powerful diagnostic tool, but should be used with caution. Boot up your computer with a Ubuntu Live CD or USB drive, and choose to run Ubuntu from the CD or USB drive. When the desktop environment loads up, open the Synaptic Package Manager by clicking on the System menu in the top-left of the screen, then selecting Administration, and then Synaptic Package Manager. Cpuburn is in the universe repository. To enable the universe repository, click on Settings in the menu at the top, and then Repositories. Add a checkmark in the box labeled “Community-maintained Open Source software (universe)”. Click close. In the main Synaptic window, click the Reload button. After the package list has reloaded and the search index has been rebuilt, enter “cpuburn” in the Quick search text box. Click the checkbox in the left column, and select Mark for Installation. Click the Apply button near the top of the window. As cpuburn installs, it will caution you about the possible dangers of its use. Assuming you wish to take the risk (and if your computer is randomly restarting constantly, it’s probably worth it), open a terminal window by clicking on the Applications menu in the top-left of the screen and then selection Applications > Terminal. Cpuburn includes a number of tools to test different types of CPUs. If your CPU is more than six years old, see the full list; for modern AMD CPUs, use the terminal command burnK7 and for modern Intel processors, use the terminal command burnP6 Our processor is an Intel, so we ran burnP6. Once it started up, it immediately pushed the CPU up to 99.7% total usage, according to the Linux utility “top”. If your computer is having a CPU, power supply, or cooling problem, then your computer is likely to shutdown within ten or fifteen minutes. Because of the strain this program puts on your computer, we don’t recommend leaving it running overnight – if there’s a problem, it should crop up relatively quickly. Cpuburn’s tools, including burnP6, have no interface; once they start running, they will start driving your CPU until you stop them. To stop a program like burnP6, press Ctrl+C in the terminal window that is running the program. Conclusion The Ubuntu Live CD provides two great testing tools to diagnose a tricky computer problem, or to stress test a new computer. While they are advanced tools that should be used with caution, they’re extremely useful and easy enough that anyone can use them. Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDCreate a Persistent Bootable Ubuntu USB Flash DriveAdding extra Repositories on UbuntuHow to Share folders with your Ubuntu Virtual Machine (guest)Building a New Computer – Part 3: Setting it Up TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause

    Read the article

  • Using the new CSS Analyzer in JavaFX Scene Builder

    - by Jerome Cambon
    As you know, JavaFX provides from the API many properties that you can set to customize or make your components to behave as you want. For instance, for a Button, you can set its font, or its max size.Using Scene Builder, these properties can be explored and modified using the inspector. However, JavaFX also provides many other properties to have a fine grained customization of your components : the css properties. These properties are typically set from a css stylesheet. For instance, you can set a background image on a Button, change the Button corners, etc... Using Scene Builder, until now, you could set a css property using the inspector Style and Stylesheet editors. But you had to go to the JavaFX css documentation to know the css properties that can be applied to a given component. Hopefully, Scene Builder 1.1 added recently a very interesting new feature : the CSS Analyzer.It allows you to explore all the css properties available for a JavaFX component, and helps you to build your css rules. A very simple example : make a Button rounded Let’s take a very simple example:you would like to customize your Buttons to make them rounded. First, enable the CSS Analyzer, using the ‘View->Show CSS Analyzer’ menu. Grow the main window, and the CSS Analyzer to get more room: Then, drop a Button from the Library to the ContentView: the CSS Analyzer is now showing the Button css properties: As you can see, there is a ‘-fx-background-radius’ css property that allow to define the radius of the background (note that you can get the associated css documentation by clicking on the property name). You can then experiment this by setting the Button style property from the inspector: As you can see in the css doc, one can set the same radius for the 4 corners by a simple number. Once the style value is applied, the Button is now rounded, as expected.Look at the CSS Analyzer: the ‘-fx-background-radius’ property has now 2 entries: the default one, and the one we just entered from the Style property. The new value “win”: it overrides the default one, and become the actual value (to highlight this, the cell background becomes blue). Now, you will certainly prefer to apply this new style to all the Buttons of your FXML document, and have a css rule for this.To do this, save you document first, and create a css file in the same directory than the new document.Create an empty css file (e.g. test.css), and attach it the the root AnchorPane, by first selecting the AnchorPane, then using the Stylesheets editor from the inspector: Add the corresponding css rule to your new test.css file, from your preferred editor (Netbeans for me ;-) and save it. .button { -fx-background-radius: 10px;} Now, select your Button and have a look at the CSS Analyzer. As you can see, the Button is inheriting the css rule (since the Button is a child of the AnchorPane), and still have its inline Style. The Inline style “win”, since it has precedence on the stylesheet. The CSS Analyzer columns are displayed by precedence order.Note the small right-arrow icons, that allow to jump to the source of the value (either test.css, or the inspector in this case).Of course, unless you want to set a specific background radius for this particular Button, you can remove the inline Style from the inspector. Changing the color of a TitledPane arrow In some cases, it can be useful to be able to select the inner element you want to style directly from the Content View . Drop a TitledPane to the Content View. Then select from the CSS Analyzer the CSS cursor (the other cursor on the left allow you to come back to ‘standard’ selection), that will allow to select an inner element: height: 62px;" align="LEFT" border="0"> … and select the TitledPane arrow, that will get a yellow background: … and the Styleable Path is updated: To define a new css rule, you can first copy the Styleable path : .. then paste it in your test.css file. Then, add an entry to set the -fx-background-color to red. You should have something like: .titled-pane:expanded .title .arrow-button .arrow { -fx-background-color : red;} As soon as the test.css is saved, the change is taken into account in Scene Builder. You can also use the Styleable Path to discover all the inner elements of TitledPane, by clicking on the arrow icon: More details You can see the CSS Analyzer in action (and many other features) from the Java One BOF: BOF4279 - In-Depth Layout and Styling with the JavaFX Scene Builder presented by my colleague Jean-Francois Denise. On the right hand, click on the Media link to go to the video (streaming) of the presa. The Scene Builder support of CSS starts at 9:20 The CSS Analyzer presentation starts at 12:50

    Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >