Search Results

Search found 4300 results on 172 pages for 'mark virtue'.

Page 95/172 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

  • Hard Drive Bad Sector marking utility

    - by Kevin Boyd
    I already have Windows XP, During installing Ubuntu(dual boot) the disk drive just stuck up at one place and doesn't seem to move ahead.. Is there a disk bad sector mark utility that just marks these sectors so that the disk doesn't seek them later. I tried running Seagate Seatools on the drive but both the short test and long test fail even before they start even chkdsk /f/r doesn't seem to work as the system locks up at stage four.

    Read the article

  • How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

    - by user11955
    Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

    Read the article

  • How to change the language of dictionary in word for mac

    - by TheLearner
    My friend is using Microsoft Word for Mac (which is a total train smash). and we want to change the spell check from English (US) to English (UK). This is what I have tried: Make a spelling mistake otherwise you can't get to spelling options. Click Tools Spelling and Grammar Options Dictionaries Change language to English (UK) and click OK Type an English (US) word 'Categorize' Click Tools Spelling and Grammar - 'Spelling and Grammar check complete' i.e. it did not mark the work incorrect.

    Read the article

  • Running psexec against Window 7?

    - by Jimmy C
    I can't seem to get psexec commands to work on Windows 7 Enterprise. I'm trying to execute a command like this: psexec.exe \\172.16.165.157 -u jc -p testing123 -c -f -i cmd.exe But, I keep getting the error: PsExec v1.94 - Execute processes remotely Copyright (C) 2001-2008 Mark Russinovich Sysinternals - www.sysinternals.com Error copying C:\WINDOWS\system32\cmd.exe to remote system: Access is denied. I'm trying to execute the command from a machine running Windows XP Professional. Has anybody seen an issue like this?

    Read the article

  • iTunes lost my music after re-plugging my external harddisk

    - by AskAboutGadgets.com
    I am storing most of my music on an external hard disk and from time to time I need to unplug this disk. After reconnecting it to my computer and starting iTunes I noticed that the individual songs stored on the external drive are now lost (they have a little exclamation mark next to them). iTunes offers me to locate the songs one by one, but I have thousands of songs. Is there a better solution to reconnect my collection in iTunes?

    Read the article

  • Tool to test USB sticks?

    - by Tony_Henrich
    Some of the files I copy to a USB stick seems to be corrupted? Maybe the stick is bad but I haven't used it much and want to know for sure. Is there a Windows utility to test the stick? Mark bad areas as bad so the file system doesn't save to them? I format before I copy but I still get corrupted files? Does chkdsk work on USB sticks reliably?

    Read the article

  • How to protect custom shapes from being reused? Visio 2010

    - by Chris
    We are building a set of documentation for our business with Visio 2010. We need to make the Visio files accessible to external consultants for review, but we want to ensure that they cannot copy any of our custom shapes or formulas. How can we protect custom shapes/stencils so that they cannot be used outside of our documents? Or, if that's not possible, how can we mark our shapes in such a way that we could prove that they were created by us?

    Read the article

  • Notepad++ highlight transparency

    - by buchtak
    I use dark themes and when I select a word, Notepad++ highlights all the occurences of that word in the current document. But the highlight color for matches other than the current word is somehow blended with the background and the highlighted text is not as clearly visible as it could be. The same thing happens when using "Find all" option in the Find dialog to mark the occurences. Is there a way to change this behavior such that the matched text has the same (full) opacity as the selected text?

    Read the article

  • vim: remove previous code indentation and convert to another

    - by ramgorur
    I have a c project with multiple files (more than 100), the codes are written in Whitesmiths style, but I want to change them into K&R style indentation. Is it possible to do using vim in an automated way ? For example I have a emacs-lisp script to achieve this -- (progn (find-file "{}") (mark-whole-buffer) (setq indent-tabs-mode nil) (untabify (point-min) (point-max)) (indent-region (point-min) (point-max) nil) (save-buffer)) I was wondering if there is a similar trick that could be done with vim.

    Read the article

  • How should I interpret site analytics with 11 pageviews in an 3 second visit?

    - by Juank
    I'm using google analytics and recently i've noticed some weird trends going on. I have a lot of visits that last mere seconds but mark several page views... more than a normal human can see in that range of time. A specific case is that the only visitor from Ireland i've had until now recorded 11 pageviews in a 3 second visit. Are these crawlers? Shouldn't google analytics filter those out?

    Read the article

  • What to do before trying to benchmark

    - by user23950
    What are the things that I should do before trying to benchmark my computer: I've got this tools for benchmarking: 3dmark cinebench geekbench juarez dx10 open source mark Do I need to have a full spyware and virus scan before proceeding?What else should I do, in order to get accurate readings.

    Read the article

  • How can i see mac folder colours on pc?

    - by user398140
    My colleagues mark folders on mac server using their macs, and sometimes tell me i've marked those folders in green. I'm wondering if there's any mean to see what colours got assigned to what folders using PC. I'm connecting to the server using smb/ssh. Solution can be either windows or linux. Please not i'm not about to change those markings, neither looking for some robust solution, just quick hack.

    Read the article

  • Invalid command 'SSLRequireSSL',

    - by Bad Programmer
    An svn server that I managed crashed. The server is up and running again, but I can't manage to get svn running anymore. I followed the instructions listed here: http://mark.koli.ch/2010/03/howto-setting-up-your-own-svn-server-using-apache-and-mod-dav-svn.html Yet when I try to start apache using /etc/init.d/httpd start I get a [FAILED] message. There is no content in the error logs. Any suggestions?

    Read the article

  • Windows 7: Always remember UAC choice for an application

    - by Svish
    I have some applications that I open from time to time, and I always get this UAC message with Do you want to allow the following program from an unknown publisher to make changes to this computer? Is there a way I can mark a single program so that won't ask me that again? Like, I think it is good that it asks me the first time, but some programs I do launch more often, and I am ok with them making changes and don't want to be asked all the time.

    Read the article

  • Linux authentication via ADS -- allowing only specific groups in PAM

    - by Kenaniah
    I'm taking the samba / winbind / PAM route to authenticate users on our linux servers from our Active Directory domain. Everything works, but I want to limit what AD groups are allowed to authenticate. Winbind / PAM currently allows any enabled user account in the active directory, and pam_winbind.so doesn't seem to heed the require_membership_of=MYDOMAIN\\mygroup parameter. Doesn't matter if I set it in the /etc/pam.d/system-auth or /etc/security/pam_winbind.conf files. How can I force winbind to honor the require_membership_of setting? Using CentOS 5.5 with up-to-date packages. Update: turns out that PAM always allows root to pass through auth, by virtue of the fact that it's root. So as long as the account exists, root will pass auth. Any other account is subjected to the auth constraints. Update 2: require_membership_of seems to be working, except for when the requesting user has the root uid. In that case, the login succeeds regardless of the require_membership_of setting. This is not an issue for any other account. How can I configure PAM to force the require_membership_of check even when the current user is root? Current PAM config is below: auth sufficient pam_winbind.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth required pam_deny.so account sufficient pam_winbind.so account sufficient pam_localuser.so account required pam_unix.so broken_shadow password ..... (excluded for brevity) session required pam_winbind.so session required pam_mkhomedir.so skel=/etc/skel umask=0077 session required pam_limits.so session required pam_unix.so require_memebership_of is currently set in the /etc/security/pam_winbind.conf file, and is working (except for the root case outlined above).

    Read the article

  • Will a 2.4Ghz WAP intefere with a 5.0Ghz WAP if placed directly next to each other

    - by Dan
    This is mostly a curiosity question to people who know more about radio and wi-fi than I. The 2.4Ghz band is massively overpopulated near my house to the point of sometimes getting 1000ms pings to the router from only a few feet away. inSSIDer finds at least 10 broadcasting SSID's within around 15 seconds of starting, so this isn't a real surprise to me! Sometimes I can get good results by changing the channel to something like 3 or 8, but it's usually temporary as the others use Auto Channel and hop around. Now, the router I have is capable of 5.0Ghz, as is the laptop I type this on. Switching to 5.0Ghz gives superb results: I can download at ~90Mbps and get consistent 1ms pings. The problem is that only this laptop supports 5.0Ghz! My question: Would I still get decent 5.0Ghz performance if I place a 2.4Ghz access point directly next to my router? And, indeed, will 2.4Ghz continue working as 'normal'? Testing would be an obvious step, but I threw all my superfluous equipment out in a recent house move. My understanding is that I should get good performance, certainly in comparison to having two devices using the same frequency range, but I do believe there will be some impact by the virtue of them being directly next to each other. (Cabling is not an option due to it being a rented house)

    Read the article

  • ProCurve ACL to prevent a subnet from leaving the switch

    - by kce
    I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

    Read the article

  • How can I create a simple Exchange 2010 backup solution?

    - by bduncanj
    I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

    Read the article

  • Problem bash completion apt-get 12.10

    - by dadexix86
    I've got an annoying problem with completion and sudo apt-get. To give an example: $ sudo apt-get in[Tab][Tab] in intel_bios_reader includeres intel_disable_clock_gating indicator-multiload intel_dpio_read info intel_dpio_write infobrowser intel_error_decode infocmp intel_forcewaked infokey intel_gpu_abrt infotocap intel_gpu_time inimf intel_gpu_top init intel_gtt init-checkconf intel_l3_parity initctl intel_reg_checker initctl2dot intel_reg_dumper initex intel_reg_read inkscape intel_reg_snapshot inkview intel_reg_write inputattach intel_sprite_on insmod intel_stepping install intel_upload_blit_large install-docs intel_upload_blit_large_gtt installfont-tl intel_upload_blit_large_map install-info intel_upload_blit_small installkernel interdiff --More-- While is working right both with just apt-get or doing it in root: $ apt-get in[Tab]stall $ sudo -i [sudo] password for davide: root@brenna:~# apt-get in[Tab]stall So the problem is using autocompletion after sudo? Not really, because $ sudo apt-[Tab][Tab] apt-add-repository apt-extracttemplates apt-key apt-cache apt-file apt-mark apt-cdrom apt-ftparchive apt-sortpkgs apt-config apt-get Summing up, the problem seems to be using sudo and auto-completion for programs options together. Any good advice for that?

    Read the article

  • GWB | 30 Posts in 60 Days Update

    - by Staff of Geeks
    One month after the contest started, we definitely have some leaders and one blogger who has reached the mark.  Keep up the good work guys, I have really enjoyed the content being produced by our bloggers. Current Winners: Enrique Lima (37 posts) - http://geekswithblogs.net/enriquelima Almost There: Stuart Brierley (28 posts) - http://geekswithblogs.net/StuartBrierley Dave Campbell (26 posts) - http://geekswithblogs.net/WynApseTechnicalMusings Eric Nelson (23 posts) - http://geekswithblogs.net/iupdateable Coming Along: Liam McLennan (17 posts) - http://geekswithblogs.net/liammclennan Christopher House (13 posts) - http://geekswithblogs.net/13DaysaWeek mbcrump (13 posts) - http://geekswithblogs.net/mbcrump Steve Michelotti (10 posts) - http://geekswithblogs.net/michelotti Michael Freidgeim (9 posts) - http://geekswithblogs.net/mnf MarkPearl (9 posts) - http://geekswithblogs.net/MarkPearl Brian Schroer (8 posts) - http://geekswithblogs.net/brians Chris Williams (8 posts) - http://geekswithblogs.net/cwilliams CatherineRussell (7 posts) - http://geekswithblogs.net/CatherineRussell Shawn Cicoria (7 posts) - http://geekswithblogs.net/cicorias Matt Christian (7 posts) - http://geekswithblogs.net/CodeBlog James Michael Hare (7 posts) - http://geekswithblogs.net/BlackRabbitCoder John Blumenauer (7 posts) - http://geekswithblogs.net/jblumenauer Scott Dorman (7 posts) - http://geekswithblogs.net/sdorman   Technorati Tags: Standings,Geekswithblogs,30 in 60

    Read the article

  • Clean Up the New Ubuntu Grub2 Boot Menu

    - by Trevor Bekolay
    Ubuntu adopted the new version of the Grub boot manager in version 9.10, getting rid of the old problematic menu.lst. Today we look at how to change the boot menu options in Grub2. Grub2 is a step forward in a lot of ways, and most of the annoying menu.lst issues from the past are gone. Still, if you’re not vigilant with removing old versions of the kernel, the boot list can still end up being longer than it needs to be. Note: You may have to hold the SHIFT button on your keyboard while booting up to get this menu to show. If only one operating system is installed on your computer, it may load it automatically without displaying this menu. Remove Old Kernel Entries The most common clean up task for the boot menu is to remove old kernel versions lying around on your machine. In our case we want to remove the 2.6.32-21-generic boot menu entries. In the past, this meant opening up /boot/grub/menu.lst…but with Grub2, if we remove the kernel package from our computer, Grub automatically removes those options. To remove old kernel versions, open up Synaptic Package Manager, found in the System > Administration menu. When it opens up, type the kernel version that you want to remove in the Quick search text field. The first few numbers should suffice. For each of the entries associated with the old kernel (e.g. linux-headers-2.6.32-21 and linux-image-2.6.32-21-generic), right-click and choose Mark for Complete Removal. Click the Apply button in the toolbar and then Apply in the summary window that pops up. Close Synaptic Package Manager. The next time you boot up your computer, the Grub menu will not contain the entries associated with the removed kernel version. Remove Any Option by Editing /etc/grub.d If you need more fine-grained control, or want to remove entries that are not kernel versions, you must change the files located in /etc/grub.d. /etc/grub.d contains files that hold the menu entries that used to be contained in /boot/grub/menu.lst. If you want to add new boot menu entries, you would create a new file in this folder, making sure to mark it as executable. If you want to remove boot menu entries, as we do, you would edit files in this folder. If we wanted to remove all of the memtest86+ entries, we could just make the 20_memtest86+ file non-executable, with the terminal command sudo chmod –x 20_memtest86+ Followed by the terminal command sudo update-grub Note that memtest86+ was not found by update-grub because it will only consider executable files. However, instead, we’re going to remove the Serial console 115200 entry for memtest86+… Open a terminal window Applications > Accessories > Terminal. In the terminal window, type in the command: sudo gedit /etc/grub.d/20_memtest86+ The menu entries are found at the bottom of this file. Comment out the menu entry for serial console 115200 by adding a “#” to the start of each line. Save and close this file. In the terminal window you opened, enter in the command sudo update-grub Note: If you don’t run update-grub, the boot menu options will not change! Now, the next time you boot up, that strange entry will be gone, and you’re left with a simple and clean boot menu. Conclusion While changing Grub2’s boot menu may seem overly complicated to legacy Grub masters, for normal users, Grub2 means that you won’t have to change the boot menu that often. Fortunately, if you do have to do it, the process is still pretty easy. For more detailed information about how to change entries in Grub2, this Ubuntu forum thread is a great resource. If you’re using an older version of Ubuntu, check out our article on how to clean up Ubuntu grub boot menu after upgrades. Similar Articles Productive Geek Tips Clean Up Ubuntu Grub Boot Menu After UpgradesReinstall Ubuntu Grub Bootloader After Windows Wipes it OutChange the GRUB Menu Timeout on UbuntuHow To Switch to Console Mode for Ubuntu VMware GuestSet Windows as Default OS when Dual Booting Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Daily Motivator (Firefox) FetchMp3 Can Download Videos & Convert Them to Mp3 Use Flixtime To Create Video Slideshows Creating a Password Reset Disk in Windows Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation"

    Read the article

  • « Le rejet des DRM risque de cloisonner le Web » pour le PDG du W3C, qui trouve que la spécification EME est un juste compromis

    Le W3C étudie une norme pour la lecture du contenu protégé dans le HTML5 qualifiée de « contraire à l'éthique » par un membre du consortiumDes développeurs de Google, Microsoft et Netflix ont proposé une nouvelle norme pour le HTML5.Le futur standard du Web HTML5 qui est de plus en plus utilisé au détriment des technologies comme Flash ou Silverlight souffre encore de quelques manquements par rapport à celles-ci. C'est le cas par exemple pour la lecture du contenu vidéo protégé.Une nouvelle proposition a été faite au W3C par David Dorwin (Google), Adrian Bateman (Microsoft) et Mark Watson (Netflix) pour permettre au HTML5 de lire du contenu protégé DRM (Digital rights management ).Bapti...

    Read the article

  • Persistent Storage in Windows Phone 7

    - by Richard Jones
    Mark Arteaga – fellow MVP just helped me with this,  thought I’d share. Windows Phone 7 SilverLight supports persistent storage, which is a great way of saving settings betweens runs of your application. However I couldn’t get it to work. If you do this to create a persistant storage instance -    private IsolatedStorageSettings userSettings = IsolatedStorageSettings.ApplicationSettings; To retrieve settings do the following - string xx = userSettings[“SomeValue”].ToString();   Hiowever the bit that got me was how to save settings, you have todo this - userSettings.Add("Hello", DateTime.Now.ToShortTimeString());           userSettings.Save(); // <- This is the bit that got me   Hope this helps others

    Read the article

  • SOA Galore: New Books for Technical Eyes Only By Bob Rhubart

    - by JuergenKress
    In my part of the world the weather has taken its seasonal turn toward the kind of cold, damp, miserable stuff that offers a major motivation to stay indoors. While I plan to spend some of the indoor time working my way through the new 50th anniversary James Bond box set, I will also devote some time to improve my mind rather than my martini-mixing skills by catching up on my reading. If you are in a similar situation, you might want to spend some of your time with these new technical books written by our community members: Oracle SOA Suite 11g Administrator's Handbook by Ahmed Aboulnaga and Arun Pareek Oracle SOA Suite 11g Developer's Cookbook by Antony Oracle BPM Suite 11g: Advanced BPMN Topics by Mark Nelson and Tanya Williams SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit  www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Technorati Tags: SOA books,BPM books,education,SOA Community,Oracle SOA,Oracle BPM,Community,OPN,Jürgen Kress

    Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >