Search Results

Search found 2911 results on 117 pages for 'restore'.

Page 95/117 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• How to bypass resume from hibernate [closed]

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• I flashed my DS4700 with a 7 series firmware, now my DS4300 cannot read the disks I moved to that lo

  - by Daniel Hoeving

  In preparation for adding a number of 1Tb SATA disks to our DS4700 I flashed the controller firmware from a 6 series (which only supports up to 2Tb logical drives) to a 7 series (which supports larger than 2Tb logical drives). Attached to this DS4700 was a EXP710 expansion drawer that we had planned to migrate out to our co-location to allieviate the storage issues we were having there. Unfortunately these two projects were planned in isolation to one another so I was at the time unaware of the issue that this would cause. Prior to migrating the drawer I was reading the "IBM TotalStorage DS4000 EXP700 and EXP710 Storage Expansion EnclosuresInstallation, User’s, and Maintenance Guide" and discovered this: Controller firmware 6.xx or earlier has a different metadata (DACstore) data structure than controller firmware 7.xx.xx.xx. Metadata consists of the array and logical drive configuration data. These two metadata data structures are not interchangeable. When powered up and in Optimal state, the storage subsystem with controller firmware level 7.xx.xx.xx can convert the metadata from the drives configured in storage subsystems with controller firmware level 6.xx or earlier to controller firmware level 7.xx.xx.xx metadata data structure. However, the storage subsystem with controller firmware level 6.xx or earlier cannot read the metadata from the drives configured in storage subsystems with controller firmware level 7.xx.xx.xx or later. I had assumed that if I deleted the logical drives and array information on the EXP710 prior to migrating it to the DS4300 (6.60.22 firmware) this would satisfy the above, unfortunately I was wrong. So my question is a) Is it possible to restore the DAC information to its factory settings, b) What tool(s) would I use to accomplish this, or c) is this a lost cause? Daniel.

  Read the article

• Error occurs when Win 7 opens

  - by user1708748

  I have an HP customized laptop barely a week old. Since yesterday it has given me an error message while opening Windows- every time. it gives error code (0x40000015) refers to an exception at location (0x0033fa4d). I have 64 bit Win 7 and had been transferring files. And installing programs. 8 GB Ram 650 gb hard drive. Not sure which program caused this. Q's that I've seen with this error code all say it occurs while shutting down. A search re. error code told me to use a removal tool. When I downloaded the tool,I got a message saying it is not compatible with Windows 7. Is that really possible? Search re. location code yielded nothing I am an intermediate user. I can restore to an earlier time but I don't know which program might do this again.

  Read the article

• Updated XAMPP with MySQL, all my tables are missing

  - by user371699

  I just updated XAMPP to a newer version, which included updating MySQL from 5.5 to 5.6. Using phpMyAdmin, however, all of my tables within my databases still appear on the left navigation panel, but the main window shows that all my databases are empty (except for information_schema, and a couple other default tables.) Clicking on a table in the navigation panel gives me a "table doesn't exist" message. It does looks like information_schema.tables doesn't have my tables, either. Can anyone assist me with this? I did make a complete backup of all my databases before the upgrade, but I first want to see if I can fix this the "normal" way. Furthermore, I'm not sure if the MySQL upgrade involved making changes to the information/performance databases, so I don't know if I can restore the old ones. Thank you. EDIT: Continuing my searching, I realized that only the INNODB databases are missing. I've tried running the following with no avail: /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp and /opt/lampp/bin $ sudo ./mysql_install_db --basedir=/opt/lampp --datadir=/opt/lampp/var/mysql The my.cnf file in /opt/lampp/etc contains the following InnoDB settings: innodb_data_home_dir = /opt/lampp/var/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_log_group_home_dir = /opt/lampp/var/mysql/ # You can set .._buffer_pool_size up to 50 - 80 % # of RAM but beware of setting memory usage too high innodb_buffer_pool_size = 16M # Deprecated in 5.6 #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size innodb_log_file_size = 5M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 What could possibly be wrong? Why is the information_schema not updating correctly? It looks like /opt/lampp/var/mysql has all my tables in it within the database directories, but they're still not showing up in information_schema.

  Read the article

• Configuring port forwarding for SSH - no response outside LAN [migrated]

  - by WinnieNicklaus

  I recently moved, and at the same time purchased a new router (Linksys E1200). Prior to the move, I had my old router set up to forward a port for SSH to servers on my LAN, and I was using DynDNS to manage the external IP address. Everything worked great. I moved and set up the new router (unfortunately, the old one is busted so I can't try things out with it), updated the DynDNS address, and attempted to restore my port forwarding settings. No joy. SSH connections time out, and pings go unanswered. But here's the weird part (i.e., key to the whole thing?): I can ping and SSH just fine from within this LAN. I'm not talking about the local 192.168.1.* addresses. I can actually SSH from a computer on my LAN to the DynDNS external address. It's only when the client is outside the LAN that connections are dropped. This surely suggests a particular point of failure, but I don't know enough to figure out what it is. I can't figure out why it would make a difference where the connections originate, unless there's a filter for "trusted" IP addresses, which is perhaps just restricted to my own. No settings have been touched on the servers, and I can't find any settings suggesting this on the router admin interface. I disabled the router's SPI firewall and "Filter anonymous traffic" setting to no avail. Has anyone heard of this behavior, and what can I do to get past it?

  Read the article

• Vista failing to load after apparently being repaired

  - by Joomaz

  Hi, I apologise if I'm a litre vague and can give more info if needed. My vista machine has been working fine until today when I tried booting it. Vista loads showing the loading bar then goes to a black screen with the cursor on which you can move. It then remains like this for several minutes, during this time the computer doesn't sound like it's doing much, it is relatively quiet. Finally the welcome screen appears. It stays on this for several minutes again and the computer reboots. This keeps happening and the machine fails to load in safe mode - the same happens. I booted the pc with the vista disk in and ran repair your computer and used the system repair. It took about 20 minutes saying it was repairing damaged giles. I booted the pc again and the same happened. I loaded the pc with yeh vista disk again and chose repair my computer again. System repair seemed to run automatically this time and agian it did the same. I rebooted and the problem persisted. I then tried system restore to a few days ago. After half a hour as it finished it said it failed due to a portion being corrupt. I am really not sure what to do now. Any advice appreciated!

  Read the article

• Browser history, by window

  - by Alex

  I use Chrome --but can switch to another browser if the feature I am about to describe is available. Browsing history, AFAIK in Chrome is sorted exclusively chronologically. Very often however, I will be working on a particular task on my laptop and have multiple (read: a lot) of tabs open in a single Chrome window for that task. Before finishing that task, I may need to work on something else --so I will open another window and minimize the other one, and start researching an entirely different issue. Over the course of a day, I may end up with 10-15 windows with many tabs each. This raises two issues: (a) memory usage and (b) quickly switching between the most relevant two or three windows. I solve these two problems like any regular guy probably would --closing windows. I want to be able to reopen specific windows that I have closed, such that the tabs that were open in that window at the time the window was closed will reopen. Ideally, closed windows will be sorted by the time they were closed and identified by the tabs that were open (even more ideally, I would be able to name these windows (contemporaneously or in the history menu)). Now that I describe this, what I am asking is: does any browser offer the ability to "save and close" windows? (This is distinct from an option to auto-restore tabs upon reopening the browser) Thank you.

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• Networking lost after update from Debian Wheezy to Jessie

  - by Charaf

  I am currently setting a Virtual Machine for development purposes. I did a big part of this configuration under Wheezy, but I need some debs that were available only on Jessie. So, I've updated the sources.list and did a dist-upgrade. Everything went well, but after the reboot, I noticed that I lost all the networking. Repositories are unreachable, as well as a simple ping google.fr returns nothing. What can I do to quickly restore networking so that I can continue my working. I have a poor connexion and can not afford to download the whole install DVDs. root@vm~# ifconfig lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:65536 Metric 1 RX packets:452 errors:0 dropped:0 overruns:0 frame:0 TX packets:452 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:164238 (160.3 KiB) TX bytes:164238 (160.3 KiB) root@vm~# I am running VMware 1.0.1 build 1379776 and the last update of Jessie (debian 3.14.4-1) Please help. Thanks.

  Read the article

• SpamAssassin bayesian score discrepancies

  - by CaptSaltyJack

  This makes my brain hurt. For some reason, SpamAssassin is giving high scores to certain emails, but when I test them on the command line, they get a low score. This one particular email has this in the header: X-Spam-Flag: YES X-Spam-Score: 8.521 X-Spam-Level: ******** X-Spam-Status: Yes, score=8.521 tagged_above=-9999 required=5 tests=[BAYES_99=3.5, BAYES_999=0.2, HTML_MESSAGE=0.001, NO_RECEIVED=-0.001, NO_RELAYS=-0.001, RAZOR2_CF_RANGE_51_100=0.5, RAZOR2_CF_RANGE_E8_51_100=1.886, RAZOR2_CHECK=0.922, URIBL_RHS_DOB=1.514] autolearn=no Yet when I dump the raw email into a file msg and run sudo su amavis -c 'spamassassin -t msg', I get this output: Content analysis details: (3.8 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 1.5 URIBL_RHS_DOB Contains an URI of a new domain (Day Old Bread) [URIs: cliobeads.com] -1.0 ALL_TRUSTED Passed through trusted hosts only via SMTP 0.0 HTML_MESSAGE BODY: HTML included in message -0.0 BAYES_20 BODY: Bayes spam probability is 5 to 20% [score: 0.1855] 1.9 RAZOR2_CF_RANGE_E8_51_100 Razor2 gives engine 8 confidence level above 50% [cf: 100] 0.5 RAZOR2_CF_RANGE_51_100 Razor2 gives confidence level above 50% [cf: 100] 0.9 RAZOR2_CHECK Listed in Razor2 (http://razor.sf.net/) I'm really confused as to why when the email comes in, it gets a completely different score attached to it than when I run spamassassin -t. Is there some other way I should be testing emails? Also, my users have the ability to drag false positives into a folder called "False Positives," and every day a cron job fires off that runs this on every message in every user's folder: sa-learn --dbpath=/var/lib/amavis/.spamassassin --ham /tmp/*-*.eml >/dev/null I ran sudo locate bayes_toks and there's definitely only one bayes DB on the system, in /var/lib/amavis/.spamassassin. I'm clueless, any help would be great and may help restore my sanity!

  Read the article

• Moving MySQL directory on an Amazon EC2 machine

  - by Traveling Tech Guy

  I'm trying to have MySQL point to a directory on an EBS volume I mounted on my EC2 machine. I took th following steps: Stopped MySQL (/etc/init.d/mysqld stop) - successful Created a MySQL directory on my volume, mounted on /vol (mkdir /vol/mysql) Copied the contents of /var/lib/mysql to /vol/mysql (cp -R /var/lib/mysql /vol/mysql) Chanded the owner and group of that directory to match the original (chown -R mysql:mysql /vol/mysql) - after this step, the 2 directories are identical. Edited the /etc/my.cnf file (commented 2 original lines): [mysqld] #datadir=/var/lib/mysql #socket=/var/lib/mysql/mysql.sock datadir=/vol/mysql socket=/vol/mysql/mysql.sock` Started MySQL (/etc/init.d/mysqld start) - FAILED The error file /var/log/mysqld.log contains the following lines: 100205 20:52:54 mysqld started 100205 20:52:54 InnoDB: Started; log sequence number 0 43665 100205 20:52:54 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.0.45' socket: '/vol/mysql/mysql.sock' port: 3306 Source distribution No other errors are available. What am I doing wrong? Where can I find the error/s encountered by MySql? If I restore the original lines, MySQL starts, leading me to believe it may be a permissions issue - but permissions are the same for both directories? Thanks!

  Read the article

• Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

  - by neezer

  For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

  Read the article

• Firebird database corruption causes

  - by Rytis

  I am running several different Firebird versions (2.0, 2.1) on multiple entry level Windows-based servers with wildly varying hardware. The only matching thing between them is that they are running same home built application with the same database structure. Lately I've been seeing massive slowdowns on multiple servers. Turns out that database gets corrupted, so each time it breaks, I get to mend, backup and restore the database, and it all is fine for some time (1-2 weeks), and then it repeats once again. Thankfully, I haven't seen any data loss or damage... yet. The thing is that every such downtime results in lost productivity, and often quite some driving for me as some of the databases are in remote locations. I've been trying to find out what's causing the corruption, but I haven't been able to. The fact that it's running on different hardware hints that it should not be a hardware based problem. If we rule out hardware issues, I have a bad feeling that it's a bug in Firebird as I'm not doing anything fancy via SQL. Do you have any idea how to find out exactly what's causing the corruption and hopefully fix the problem?

  Read the article

• OS X Hard drive recovery

  - by Adam

  I am trying to recover data from a bad Seagate 1TB hard drive in a 2010 iMac. One day the iMac wouldn't boot (stuck at gray screen on startup). I removed the hard drive from the iMac and connected it to a MacBook using a 3.5" HDD to USB adapter. The hard drive wouldn't mount but it did display in Disk Utility that that there were 2 partitions on the disk. I tried to run Disk Warrior and it showed thousands of errors but still wouldn't mount. At this time the hard drive only show one partition in Disk Utility. Next I tried putting the hard drive in a desktop PC and running Spin Rite - which then gave me several division overflow errors (even with running Spin Rite with a newer version of DOS). The SMART status on the drive reports that the drive has had failures and HD Tune referenced the drive had once hit 59 degrees celsius. Disk Utility gives me the following message when running a pair: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Overall, the hard drive spins up and sounds OK - there are no clicking noises but the hard drive won't mount and displays as a light gray "Macintosh HD" in disk utility. Any tips or advice on how to recover data on this drive would be GREATLY appreciated! Are there any other tools I can try before calling it quits on this drive? Thank you

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Need help diagnosing my machine

  - by Tom Collins

  I have something that just slows my computer to a crawl sometimes. Not running anything big. Yesterday all I had running (besides background apps) were Firefox & Windows Explorer and could barely even switch screens. Nothing showing up in the task manager as hogging CPUs. I have all non-essential services stopped (MySQl & MSSQL) unless I need them. I made some restore points not long ago, but they disappeared. This is a development mach with a LOT of apps installed, so I really, really do not want to re-install Windows. So, what I'm looking for are ideas or tools I can use to help diagnose this problem. The only clues I have is this started right after I installed Office 2013 (with Office 2010 still installed as well) installed Visual Studio 2012 (also keeping 2010 as a co-install) and installed MSSQL 2012 (upgrade from 2008, no co-install) Also, computer runs fine in Safe Mode. I've just ran out of ideas of what to check. Any help / suggestions would much appreciated. Thanks P.S. I'm running Win 7 Pro (x64). Office is also 64 bit. Visual Studio & MSSQL are 64 bit if that option was available (not sure).

  Read the article

• Flushing iptables broke my pipe, how can I save my instance?

  - by Niels

  I was setting up my iptables when I performed a iptables -F and my ssh pipe broke. This is the last output of my session: root@alfapaints:~# iptables -L Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW,ESTABLISHED tcp dpt:2222 ACCEPT tcp -- li465-68.members.linode.com anywhere state NEW,ESTABLISHED tcp dpt:nrpe ACCEPT tcp -- anywhere anywhere tcp dpt:9200 state NEW,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http state NEW,ESTABLISHED ACCEPT udp -- anywhere anywhere udp spt:domain Chain FORWARD (policy DROP) target prot opt source destination Chain OUTPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state ESTABLISHED tcp spt:2222 ACCEPT tcp -- anywhere anywhere state ESTABLISHED tcp spt:nrpe ACCEPT tcp -- anywhere anywhere tcp spt:9200 state ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp spt:http state ESTABLISHED ACCEPT udp -- anywhere anywhere udp dpt:domain root@alfapaints:~# iptables -F Write failed: Broken pipe I tested my connection just before and I was able to connect with ssh. Now I did a nmap scan and not a single port is open anymore. I know my VPS is running on VMWare ESXi, could a reboot help? Or if not could I attach and mount the disk to another vm to save the data? Does anybody have some advise? And maybe an explanation what happend or what could have cause my pipe to break? ps: I didn't save my rules on the config directories of iptables. But used a file I stored in ~/rules.config to apply my rules like this: iptables-restore < rules.config So probably a reboot would help? Thanks a lot in advance.

  Read the article

• redirect temporarily STDOUT to another file descriptor, but still to screen

  - by Carlos Campderrós

  I'm making a script that executes some commands inside, and these commands show some output on STDOUT (and STDERR as well, but that's no problem). I need that my script generates a .tar.gz file to STDOUT, so the output of some commands executed in the script also go to STDOUT and this ends with a not valid .tar.gz file in the output. So, in short, it's possible to output the first commands to the screen (as I still want to see the output) but not via STDOUT? Also I would like to keep the STDERR untouched so only error messages appear there. A simple example of what I mean. This would be my script: #!/bin/bash # the output of these commands shouldn't go to STDOUT, but still appear on screen some_cmd foo bar other_cmd baz #the following command creates a tar.gz of the "whatever" folder, #and outputs the result to STDOUT tar zc whatever/ I've tried messing with exec and the file descriptors, but I still can't get it to work: #!/bin/bash # save STDOUT to #3 exec 3>&1 # the output of these commands should go to #3 and screen, but not STDOUT some_cmd foo bar other_cmd baz # restore STDOUT exec 1>&3 # the output of this command should be the only one that goes to STDOUT tar zc whatever/ I guess I'm lacking closing STDOUT after the first exec and reopen it again or something, but I can't find the right way to do it (right now the result is the same as if I didn't add the execs

  Read the article

• Windows Server 2003 DC hangs after network drivers update

  - by tcv

  Earlier today, we attempted to update the Broadcom BCM5716C network drivers on a Windows Server 2003. (Dell PowerEdge T310, FWIW). Since then we have not been able to boot the server in any normal mode. Safe Mode works. Safe Mode with Networking and regular bootups hang at "Applying Network Settings." I haven't tried Last Known Good Configuration nor have I tried Directory Services Restore Mode. I should also mention that the longest I've allowed "Applying Network Settings" was perhaps 30 minutes. I spoke to Dell since the server is under a basic warranty. They sent me the original Broadcom drivers. The trouble seems to be, however, that since I can only boot in Safe Mode, I can't install the application package as given. In safe mode, I receive the error: "The system administrator has set policies to prohibit this installation." I can install the drivers independently, but that doesn't allow the NICs to work. The most I've been able to get are Code 10 errors on each NIC. I plan to get back to the site tomorrow to attempt installation of a different NIC. I'm wondering what else I can try.

  Read the article

• SQL Server 2008 R2 mirroring failing

  - by andriusn

  I have two Windows 2008 R2 (Amazon EC2) instances running SQL Server 2008 R2. I use 9TB striped disks (9x1TB EBS volumes) for storage. One server is running as principal and second one as mirror. Both started from the same image, database and tlog files located on striped disk. Mirror server failed 3 times in last 2 months with errors: EventID 823 The operating system returned error 2(The system cannot find the file specified.) to SQL Server during a write at offset 0x00000048058a00 in file 'D:\TLogs***_log.ldf'. Additional messages in the SQL Server error log and system event log may provide more detail. This is a severe system-level error condition that threatens database integrity and must be corrected immediately. Complete a full database consistency check (DBCC CHECKDB). This error can be caused by many factors; for more information, see SQL Server Books Online. and EventID 1454 Database mirroring will be suspended. Server instance 'xxxxxxxxxx' encountered error 823, state 6, severity 24 when it was acting as a mirroring partner for database '***'. The database mirroring partners might try to recover automatically from the error and resume the mirroring session. For more information, view the error log for additional error messages. followed by EventID 19019 The MSSQLSERVER service terminated unexpectedly. After this rebooting instance is necessary to restore mirroring. First two times I thought it was hardware related (striped disk failure) and relaunched instance on new hardware. But the issue is back after few weeks again. It only affects mirror instances. Any help would be really appreciated. Thanks.

  Read the article

• Why does this batch script terminate unexpectedly?

  - by neurolysis

  This batch script terminates when %CHECKCONTINUE% is given a null value by not inputting anything on line 13 (SET /p CHECKCONTINUE=Okay to continue? (y/n):), why is this? @ECHO OFF SETLOCAL TITLE Registry restore script REM Restores registry settings and disables the cloud SET %CHECKCONTINUE%= :listaction ECHO I'm about to... ECHO 1.) Remove the registry data that specifies settings for TF2 ECHO 2.) Forcibly disable Steam Cloud. ECHO. SET /p CHECKCONTINUE=Okay to continue? (y/n): REM No? IF %CHECKCONTINUE%==n GOTO exit IF %CHECKCONTINUE%==no GOTO exit REM Yes? IF %CHECKCONTINUE%==y GOTO start IF %CHECKCONTINUE%==yes GOTO start REM Did they put something else? IF DEFINED %CHECKCONTINUE% GOTO loop-notvalid REM Did they not put anything at all? IF NOT DEFINED %CHECKCONTINUE% GOTO loop-noreply :start REM Delete application specific data REG DELETE HKEY_CURRENT_USER\Software\Valve\Source\tf\Settings /f REG DELETE HKEY_CURRENT_USER\Software\Valve\Steam\Apps\440 /f REM Disable Steam Cloud for TF2 REG ADD HKEY_CURRENT_USER\Software\Valve\Steam\Apps\440 /v Cloud /t REG_DWORD /d "0x0" /f :exit ENDLOCAL EXIT :loop-notvalid ECHO. ECHO That's not a valid reply. Try again. ECHO. SET %CHECKCONTINUE%= GOTO listaction :loop-noreply ECHO. ECHO You must enter a reply. ECHO. SET %CHECKCONTINUE%= GOTO listaction

  Read the article

• Uninstall IIS on Windows 7

  - by CJM

  I've just rebuilt my development machine and installed IIS. I then installed the Web Deployment tool and used this to restore my previously-backed-up websites to the clean machine. Unfortunately the restoration didn't work correctly/fully. I couldn't easily correct the problem, so I decided to uninstall/reinstall IIS and recreate the sites manually. I uninstalled IIS and rebooted, but there was still plenty of stuff left around such as various files in /windows/system32/inetsrv/ which I tried to delete manually (with limited success!). I rebooted again and tried to reinstall IIS - it reported an error (no meaningful message) and requested another reboot. The event log includes the following errors: The World Wide Web Publishing Service (WWW Service) did not register the URL prefix http://*:80/gallery for site 1. The site has been disabled. and Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. I'd like to avoid another rebuild. Can I completely remove IIS, such that I can reinstall it from scratch? Or can I 'fix' the current setup so that IIS will reinstall over what is already there?

  Read the article

• Android failure to boot on LG [migrated]

  - by Ukavi

  I need to recover data from my AT&T LG Thrill Android Phone Background: My AT&T LG Thrill phone's battery died a couple of days ago because I forgot to charge it. When I charged the phone and tried to turn it on, it showed the LG logo followed by the dropping balls and the AT&T "Rethink Possible" screen. I then get a mesage that the Application Google Services Framework has crashed and the phone goes into a loop with the dropping balls showing again followed by "Rethink Possible" screen. This sequence repeats itself over and over and the phone does not get out of this loop. I have been able to go into the recovery screen (both Safe Mode and the Android Recovery Service) and have cleared cache, etc. However, I DO NOT want to wipe user data and restore to factory settings as this will wipe all of my data (pictures, application data, etc). Solution Needed: I need a suggestion to a way of accessing my data so that I can back it up onto an SD card/computer. I DO NOT want to root the phone as this may void the warranty. What I'm looking for is a way of perhaps putting the original flash image on the micro SD card and then have the phone read that image. Or some other similar solution that will get the phone out of this loop and allow me to get to the data.

  Read the article

• How is Apache still working?

  - by PJ

  Recently, I decided to set up a local development environment for my work projects. I'm a PHP developer, with just enough knowledge of Linux and Apache to break things mightily. To get the local environment looking like my work environment, I had to upgrade PHP. When I did, Apache wouldn't restart. I decided I wanted to start fresh (this is where things went wrong) and that I'd reinstall Apache and PHP using MacPorts. So, I went through and tried to delete all the Apache files. Yup. I ran locate apache2 and deleted any folders that looked important. (I know, I know) Then I did a /usr/libexec/locate.updatedb to make sure everything was up to date. I even restarted my machine, just to make sure. The issue is, http://localhost still works. As does an alias I set up, http://butler. Shouldn't they not work? Now that I'm this far in, are there any tips for how to completely remove Apache so I can start over? Worst case, I have a timemachine backup, so I can always just restore that... Thanks in advance.

  Read the article

• Set default tab url in firefox 14

  - by sebster

  In the latest firefox update, new tabs show -instead of the previously default blank page- a window of recently viewed pages. Before this was available, I had installed an 'addon' to allow this (called 'fvd speed dial'). It worked fine however I have since delete.d this as it is no longer needed but still loads the page where the addon was housed:'chrome://fvd.speeddial/content/fvd_about_blank.html'. I have reinstalled firefox yet the same problem still occurs. On the 'about:config' page I have found the setting 'browser.newtab.url' but do not know the default url. Is there any way to remedy this? I will just add, I appologise if this is not the case with the new tab feature. It is all I have gathered from the firefox update page. Also, I do not want to, ideally, simply restore my settings as I have changed some of them (such as the search bar, that work fine. I am on windows-xp, home edition. Not sure of what service pack.

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >