Search Results

Search found 3293 results on 132 pages for 'vmware workstation'.

Page 95/132 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• Linux Live CD for old computer

  - by Joel Coehoorn

  I have a pentium II (that's right, pentium II) with a scant 200MB of ram. This was a high-end workstation in it's day. The machine currently runs dos on a raid array, and I need to pull some data from it. I figure my best chance at this is to use a linux live cd to copy the data to one of our active directory network shares (there is a network card in the machine). Unfortunately, my linux skills are abysmal, so I'm not sure where to get started: Where should I look to find a linux cd that will run well on such an old system Since I'm likely gonna need to be command-line only, what do I need to do to configure the network card and mount the network share via the command line? Bonus points: exact syntax needed to copy and convert the entire volume for use in VMware server 2.0, but really just copying all the data should be enough.

  Read the article

• Slow LAN transfer from 3rd party computer

  - by Chris

  Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

  Read the article

• Machine account authentication on Radius server

  - by O.Shevchenko

  My workstation is under Linux. I have an Active Directory domain controller + Radius server on Windows 2008. I can verify user account 'radius-01' using 'radtest' tool: $ radtest -t pap radius-01 password123 195.234.133.32 1812 password123 Sending Access-Request of id 98 to 195.234.73.2 port 1812 User-Name = "radius-01" User-Password = "password123" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 rad_recv: Access-Accept packet from host 195.234.133.32 port 1812, id=98, length=84 Framed-MTU = 1344 Framed-Protocol = PPP Service-Type = Framed-User Class = 0x537004f00000013700010200ac1c0... I have joined my Linux PC to Active Directory domain ARB-HRK using Samba: [root@shev-arb]# net ads testjoin Join is OK I can dump machine password: [root@shev-arb]# tdbdump /var/lib/samba/private/secrets.tdb { key(34) = "SECRETS/MACHINE_PASSWORD/ARB-HRK" data(15) = "yGgXJsquRnpT0g\00" } How can i authenticate my machine account on Radius server? Do anybody know any tools for this, like: radtest shev-arb$ yGgXJsquRnpT0g 195.234.133.32 1812 password123 (this command fails)

  Read the article

• emacs and putty on windows 7

  - by twilbrand

  My workstation was recently updated to Windows 7. I've downloaded putty and have configured it to the same settings I had under Vista. Whenever I ssh to a vm running Centos 5.4 and try to run emacs on a file, I'm getting an error about a connection to an X server: [ecto1 ~]$ emacs foo.bar Connection lost to X server `localhost:10.0' I never received this error message when I had Vista. I can get around it by aliasing emacs to 'emacs -nw', but I don't feel that I should have to do this. My co-worker has the same hardware that had the same upgrade and his sessions do not seem to be doing this. Any advice? I can't find anything on google and don't know where else to start. [ecto1 ~]$ emacs -version GNU Emacs 21.4.1

  Read the article

• DNS is resolving fine but can't access the server (unless changing /etc/hosts)

  - by victor hugo

  Hi all, I have a VPS server with a public IP, I added some A entries in my name server like svn.example.com - 1.1.1.1 Also I added some entries in my workstation /etc/hosts file in order to work with the domains meanwhile the DNSs were refreshed. It's been around 3 days from this and I configures everything in my server (using the hosts file), the DNSs are ready and I removed the entries but for my surprise I can access the servers nor anything in my domain or sub-domains (even a ping doesn't work). I've triple checked and the DNSs are OK. I don't know too much about DNSs . Any help would be appreciated. The IP address of my VPS is 74.63.223.43 I have these domain names, all pointing to the same IP (using A entries) hartoingenio.com www.hartoingenio.com svn.hartoingenio.com

  Read the article

• SSH not working after Restoring Running-Config to a Replacement Cisco Router

  - by Kyle Brandt

  One of my Cisco routers died over the weekend, Cisco sent the replacement and I restored the the config using copy tftp: running-config. Everything seems to work fine but I can no longer ssh into the router (I can telnet). The connection is refused, so it isn't listening on port 22 it seems like. I had previously backed up the config by just doing ssh router 'show run' > backup_config from my workstation. So: Is there anything wrong with my method of backup vs copy running-config tftp:? I know I haven't given any debug information, but is there something typical I need to do to get ssh working?

  Read the article

• How to lock the c prompt?

  - by allindal

  Is there anyway to lock the command prompt? I need my computer to require a password to use the command prompt. I lock the workstation occasionally but sometimes I forget and if I could just prevent my roommate from doing the "c: net user user *" to change my password it would be great. I do not want to have to use the rundll.32 user command with script to automatically lock the computer. Just a way to lock the c prompt. Sorry for not saying this earlier, I'm running a vista 32bit Asus gene II motherboard with a core i7 CPU

  Read the article

• NAT and ISP Subnet when load balancing on pfsense?

  - by dannymcc

  I have a pfsense box that I'm trying to plan the configuration for. I am going to be load balancing two ISP's, each with their own /29 static IP subnet. The question I have is in relation to the way those IP's are associated with workstations on the local network. Currently I have some workstations with local (192.168.1.0/29) IP addresses, and other more complicated workstation setups have their own public IP address. Some of the more complicated systems have a NAT 1:1 configuration where I forward a public IP address to a local IP address. Others however are directly on the ISP subnet and cannot be seen on our local network. Is this configuration possible with pfsense? If so, what terms should I be looking through the documentation for? Here is a simple/brief diagram of what I am trying to achieve.

  Read the article

• Why does Apache ignore my Directory block?

  - by Codemonkey

  I just moved my projects into a new workstation. I'm having trouble getting my Apache installation to acknowledge my .htaccess files. This is my /etc/apache2/conf.d/dev config file: <Directory /home/codemonkey/dev/myproject/> Options -Indexes AllowOverride All Order Allow,Deny Deny from all </Directory> I know the config file is being included by Apache because it complains if I put erroneous syntax in it (Action 'configtest' fails). My project is reachable through Apache by a symlink in the /var/www directory. The server is running with my user and group, so it has my permissions. My entire dev folder has permissions set to 770 recursively. Despite all this, I'm still getting an indexed display of my project folder when I visit http://localhost/myproject. Why isn't the above config making it impossible to view the folder in the browser?

  Read the article

• Does HyperV allow binding physical NIC on virtual machine with promiscues mode?

  - by MadBoy

  I have HyperV on Windows 2008 Enterprise R2 installed with some Virtual Server running that I wanted to have ISA or NTOP to monitor traffic. I've added additional physical NIC to server and wanted to use this NIC as traffic monitor (I've enabled port mirroring on switch). I can see on physical machine that runs HyperV a lot of traffic coming to the NIC so port mirroring works fine. However in virtual machine even thou I've assigned that NIC to only this one and only server it sees 0 packets. In VWMare Workstation it worked without problem and I could see mirrored traffic on VM. Should this be possible or HyperV is crippled?

  Read the article

• Lenovo ThinkPad: What does the PWMDBSVC.exe service do? It's writing a C:\Log.txt file.

  - by thinkPadUser

  I found a file that keeps popping up in my C:\ drive root, Log.txt ... after installing Process Monitor and seeing what process was writing to it, I came across PWMDBSVC.exe, which appears to be part of the Lenovo ThinkPad software. Even if I delete it, I can get it to re-create the Log.txt when I lock and unlock my workstation. Does anybody know what this software does and whether it is safe to disable? I searched Google already and got the usual pile of useless hits on the process name but nothing seemingly definitive!

  Read the article

• Command-line access for Apple Time Machine?

  - by Stefan Lasiewski

  We use Apple's Time Machine to back up our workstations at the office. If I want to restore a file, I need to open up the Time Machine GUI and browse files there. The GUI is ugly eye-candy and gets in my way. Is there a way to browse the Time Machine archive using the Mac's command-line? I'm used to Netapps and other storage appliances. I use backintime for my Ubuntu workstation. To restore a file with one of those systems, you can restore a file with a simple command like: cp .snapshot/daily.0/filename.txt . or cp /backup/backintime/20100611-000002/backup/etc/shadow /etc/shadow Is there an equivalent for Apple's Time Machine?

  Read the article

• Windows 8 mail cause event 529 when connect to exchange

  - by holian

  I set my company exchange mailbox in Windows 8.1 mail. (outsite). Everything works fine, but after i start the Windows 8.1 mail i get event with id 529 in the security log continously. Reason: Unknown user name or bad password Username: [email protected] range: Type of login: 8 Logon Process: Advapi Authentication Package: Negotiate Workstation Name: SERVERNAME Caller User Name: SERVERNAME $ Calling range BAR NUL Caller Logon ID: (0x0, 0x3E7) Caller Process ID: 4384 Transmitted services: - Source Network Address: 56.43.213.122 Source Port: 55 698 If i close windows mail, events stop flooding the security log in the server. Connection parameters in windwos 8: email:[email protected] password domain:company.local username:myemail server:mydomain.dyndns.org SSL:yes. Any idea whats the problem? I can check my mail, with the same setting on my android phone without any problem. Thank you

  Read the article

• Ubuntu Server 10.10 vs. Fedora Server 14 for Mono.NET app hosting in VM

  - by Abbas

  Ubuntu Server 10.10 vs. Fedora Server 14 I want to create a web-server running Mono, MySQL 5.5 and OpenLDAP running as a VM (on VMWare Workstation). Searching “Ubuntu Server vs. Fedora Server” mostly yields flame wars and noise. There are a few good articles available but they are either out-of-date or don’t offer very convincing arguments. I know the answer is most likely to be “it depends” but I wanted to harness the collective wisdom on ServerFault and get opinions, experiences and factual information to the extent possible. My selection criteria would be (other than what is mentioned above): Ease of use Ease of development Reliability Security

  Read the article

• Is there anything that can be done to make X forwarding over LAN less painful?

  - by Earlz

  I have two *nix machines that I like to remotely do graphical things sometimes with. One of those machines is my Arch Linux media server, and another is my OpenBSD router/general server. My current task was installing a Windows XP over virtual box on my media server. I preferred to do the installation from my main workstation so that I could continue to watch TV from my media server on it's "actual" display. I soon noticed that X forwarding is quite painful though, even over low-latency LAN connections. Are there any settings I can tweak to make it a bit less painfully slow, jittery, and laggy? My LAN is rather small, 100Mbit, and ping times to the other box average at about 0.15ms. Also, I know Virtualbox has a VNC mode it can use instead of doing X forwarding, but this particular task was just an example

  Read the article

• Workflow: suggest a versioning and file control for Designer and Developer

  - by Pennf0lio

  Our company are having hard time managing project files and managing versions of PSD, HTML, PHP, and CSS files. Can anyone recommend a good software or workflow to handle files and versions. Here's my common scenario: I work for a project in my computer, it could be a Website mockup or a coding project. I then save all the files locally in my workstation. I'll then upload all the project files in the server connected in our network to have a backup. In my files, I usually append a "r1" for revisions, like "WebsiteMockup_r1" or "WebsiteMockup_r2". I need somehow to synchronize all my local files to the server and have some versions options.

  Read the article

• Motherboard memory question

  - by JERiv

  I am currently drawing up specs on a new workstation for my office. I am considering the Asus P6X58D for a motherboard. This board's specs list it as supporting 24 gigs of memory. Suppose I were to use six four gig memory cards and then two video cards with 1 gig of memory apiece. Is the maximum supported memory similar to how 32 bit operating systems only have enough address space for 4 gigs of memory? Simply: Will the board post? If so, will the system be able to address all the memory, both the 24 gigs on the ddr3 bus and the 3 gigs on the graphics card?

  Read the article

• Do you work in your server room?

  - by Gary Richardson

  I once had a job offer from a company that wanted my workstation to be in the AC controlled, noisy server room with no natural light. I'm not sure what their motivation was. Possibly it made sense to them for me to be close to the servers, or possibly they wanted to save the desk space for other employees. I turned down the job (for many reasons, including the working environment). Is this a common practice? Do you work in your LAN room? How do you cope?

  Read the article

• script Disk Management configuration

  - by Joseph

  I have 10 workstations with large monitors that have USB slots and several card readers built in. The card readers cannot be disabled and will map to drive letters when I image the computers. I go into Disk Management and delete the drive mappings and add mappings to a single folder in C:\ with a folder for each slot. I have to do this because of scripts that run that are expecting specific letter drive mappings to network resources. Is there a way to script the deleting and adding of drive mappings instead of having to use the Disk Management GUI manually on each workstation? The workstations are running XP Professional.

  Read the article

• How To: Transfer Categories in Outlook 2007 from One Installation to Another Using Google Sync

  - by nicorellius

  I use Outlook 2007 for email. I also happen to use the categories for organizing my mail. This function is cool, because you can use keyboard shortcuts that make categorizing mail quick and easy. The problem I am having is that, since I use Google Apps Sync at home and at work, I can't seem to figure out how to transfer the existing category assignments that I spent months creating at work. As my email comes and goes, I assign this and that, with thousands of messages all belonging to specific categories. When I finally installed and started using Google Apps Sync at home, the synchronization process works great, but all my messages are blank, i.e., don't have the color categories I assigned at work. What's worse, I actually changed computers at work, and now am facing the same problem on the new workstation. Using: Windows XP Pro, Outlook 2007, Google Apps. Anyone run into this and find a solution?

  Read the article

• Quick and dirty user management service for Linux VMs?

  - by quack quixote

  Background I have a home server running Debian, and a workstation that runs various VirtualBox VMs (mostly Linuxen but some Windows). At the moment, I'm creating my main user account anew for every new Linux VM. I'd like to make use of a centralized user-management scheme instead, so I can just configure the new VMs for the directory technology and let them handle user lookups automatically. The last time I worked with anything like this, NIS+ was still in fashion. I have a vague notion of what LDAP and Active Directory are, but no knowledge of how to configure them for what I want. Question What user-management/network-directory technology should I use for providing user accounts to my network? The server must run on Debian Lenny. Client configuration should be simple point-at-server-and-go. I need an example configuration for one sample user account. (nice-to-have) I may want to mount the user's home directory from the server. (nice-to-have) The same configuration works with Windows clients.

  Read the article

• Logon script does not run for all users

  - by Herohtar

  We have a standalone common-use workstation running Windows XP Pro SP3 and have created a script using Javascript (scriptname.js) that is to be run for each user. The file was added as a user logon script via gpedit.msc and tested using a newly created user account as well as an existing user account. The script ran and functioned as intended on both accounts; however, a few existing users have informed us that the script is not running on their accounts. All user accounts are members of the same groups and have identical permissions. We already have an existing script (but in this case, a batch file) that is applied in the same manner and it runs for all accounts without any problems. Furthermore, on the accounts where the new script does not run during logon, it can still be run manually and works fine. So the question is: what would cause this script to not run during logon on certain accounts? Thanks!

  Read the article

• Cross-Forest Trust

  - by cdalley

  I am looking at testing a cross-domain trust we can have two domain controllers (with different forests and domain names) setup so we can move everyone onto the new domain. We do NOT run exchange on site and we do not have any links to O365 to AD currently. Onto the problem: I have setup two DCs in a Virtual Machine: They are on the same network 192.168.0.* The Windows 2003 server: Name: OLDSRVR "Clone" of our current Domain Controller IP: 192.168.0.1 Domain: internal.test.com The Windows 2012 server: Name: ADCTEST01 Brand new domain setup from scratch separate to internal.test.com Domain: internal.test2.com IP: 192.168.0.2 OLDSRVR can only see ADCTEST if it has dynamic IP set. If I set a static IP it cannot see it. If I try using the dynamic IP and try to join it gets to the end then complains "??The trust relationship between this workstation and the primary domain failed" Any ideas?

  Read the article

• What is a preferred method for automatically configuring and setting up an Ubuntu instance?

  - by sutch

  I am tired of manually configuring instances of Ubuntu for testing web applications and for setting up workstations. I'm even more frustrated by the issues caused by inconsistent configurations. Is there a method (hopefully not too time consuming to learn and setup) that allows for automation of the setup and configuration of an Ubuntu server or workstation from an ISO. This is primarily for virtual machine instances, but it would be helpful to also create instances on hardware. I am specifically looking for a method to automate the installation of libraries (apt-get), configure services (such as Apache and MySQL), add 3rd party software (download, extract and build), and add libraries to scripting languages (for example, Ruby Gems or CPAN packages for Perl).

  Read the article

• Why am I getting 'undefined method' exceptions when executing 'run_list add', 'run_list remove' and 'rackspace server delete'?

  - by Peter Groves

  [Originally posted this to opscode forum, got no response] I’m testing out a free hosted chef-server account and multiple subcommands are failing with ‘Unexpected Errors’. Perhaps my version and the server version are incompatible? OS: Ubuntu 12.04LTS Local Chef: 10.12.0 (Installed through gem) Local Ruby: 1.8.7 Also, the workstation machine has been manually configured, but the client(s) I’ve been experimenting with are launched with the Rackspace plugin (using ‘knife rackspace server create…’) The problem commands seem to fail when talking to the host chef-server, however, before it ever tries to modify the client, so I don’t believe that’s where the problem exists. The virtual-servers that are launched by ‘knife rackspace server create’ are launched properly but then deleting them with knife fails. If I include a recipe in the run_list when I create the server, the recipe is properly added to the run_list. If I try to add it later or remove the one that there server was initialized with, those commands fail. Here is the output of a few relevant commands (with stacktraces): https://gist.github.com/7100ada3fd6690113697

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >