Search Results

Search found 19382 results on 776 pages for 'multiple'.

Page 97/776 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• conhost.exe shows multiple times

  - by kimberly montgomery

  I have windows 7 and task mgr shows about 20 conhost.exe's running???????

  Read the article

• IPMI queries to multiple nodes at once

  - by lorin

  I'm using IPMI to manage some nodes in a cluster. I'd like to be able to submit IPMI queries to all of the nodes in parallel. Something similar to Cluster SSH or tentakel, except that it wraps ipmitool instead of ssh. Are there any tools like that?

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• Resolving ambiguous this pointer in C++

  - by Paul Tevis

  I'm trying to derive a new class from an old one. The base class declaration looks like this: class Driver : public Plugin, public CmdObject { protected: Driver(); public: static Driver* GetInstance(); virtual Engine& GetEngine(); public: // Plugin methods... virtual bool InitPlugin (Mgr* pMgr); virtual bool Open(); virtual bool Close(); // CmdObject virtual bool ExecObjCmd(uint16 cmdID, uint16 nbParams, CommandParam *pParams, CmdChannelError& error); Mgr *m_pMgr; protected: Services *m_pServices; Engine m_Engine; }; Its constructor looks like this: Driver::Driver() : YCmdObject("Driver", (CmdObjectType)100, true), m_Engine("MyEngine") { Services *m_pServices = NULL; Mgr *m_pMgr = NULL; } So when I created my derived class, I first tried to simply inherit from the base class: class NewDriver : public Driver and copy the constructor: NewDriver::NewDriver() : CmdObject("NewDriver", (EYCmdObjectType)100, true), m_Engine("MyNewEngine") { Services *m_pServices = NULL; Mgr *m_pMgr = NULL; } The compiler (VisualDSP++ 5.0 from Analog Devices) didn't like this: ".\NewDriver.cpp", line 10: cc0293: error: indirect nonvirtual base class is not allowed CmdObject("NewDriver", (EYCmdObjectType)100, true), That made sense, so I decided to directly inherit from Plugin and CmdObject. To avoid multiple inheritance ambiguity problems (so I thought), I used virtual inheritance: class NewDriver : public Driver, public virtual Plugin, public virtual CmdObject But then, in the implementation of a virtual method in NewDriver, I tried to call the Mgr::RegisterPlugin method that takes a Plugin*, and I got this: ".\NewDriver.cpp", line 89: cc0286: error: base class "Plugin" is ambiguous if (!m_pMgr->RegisterPlugin(this)) How is the this pointer ambiguous, and how do I resolve it? Thanks, --Paul

  Read the article

• Redirect audio from multiple Terminal Services sessions

  - by DougN

  When logged into a Remote Desktop session, you can request the audio be brought to the local computer (redirected audio). You hear the audio generated by your session. Is there anyway to have the audio generated by other sessions also redirected and forwarded to the local computer?

  Read the article

• SSH: Tunnel multiple ports to remote server

  - by user1594322

  See attached diagram. Host A - Windows server Host B - Linux server Host C - VMWare ESXi server From host A I can SSH to host B over the VPN tunnel. I can ping host C from host B, but not from host A. I am assuming this is because host C has lost its default gateway. Host C is a VMWware ESXi server, so I would need to tunnel several ports (80,443,902) in order to reach host C from host A. What is the correct ssh syntax to create the tunnel in order to reach host C from host A, and can I do it using a single command, or do I need to run three commands (one for each port, 80,443,902)?

  Read the article

• Combine multiple unix commands into one output

  - by Ben McCormack

  I need to search our mail logs for a specific e-mail address. We keep a current file named maillog as well as a week's worth of .bz2 files in the same folder. Currently, I'm running the following commands to search for the file: grep [email protected] maillog bzgrep [email protected] *.bz2 Is there a way combine the grep and bzgrep commands into a single output? That way, I could pipe the combined results to a single e-mail or a single file.

  Read the article

• IPcop Multiple WAN Subnets

  - by obsidian

  We have an IPcop firewall and have had no issues with it. We've had a block of 10 IP addresses from our colocation provider and have been able port forward from those to internal servers as needed. We've recently needed additional IPs and the colocation provider issued an additional block of 10. The problem: The 10 new IP addresses issued are in a different subnet with a different gateway. The question: How do I add the new gateway into IPcop? How do I make it so that any outbound traffic in response to any inbound traffic from a new IP go back out through the new gateway? I attempted to add a static route via the console using the following command: route add -net x.x.x.x gw x.x.x.x netmask 255.255.255.192 I also added the new IPs as aliases and setup port forwarding as I've done with the existing IP block. However, when I attempt to access a web server from an external workstation, it just times out. Thanks in advance for your assistance.

  Read the article

• Rails + Nginx + Unicorn multiple apps

  - by Mikhail Nikalyukin

  I get the server where is currently installed two apps and i need to add another one, here is my configs. nginx.conf user www-data www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Disable unknown domains ## server { listen 80 default; server_name _; return 444; } ## # Virtual Host Configs ## include /home/ruby/apps/*/shared/config/nginx.conf; } unicorn.rb deploy_to = "/home/ruby/apps/staging.domain.com" rails_root = "#{deploy_to}/current" pid_file = "#{deploy_to}/shared/pids/unicorn.pid" socket_file= "#{deploy_to}/shared/sockets/.sock" log_file = "#{rails_root}/log/unicorn.log" err_log = "#{rails_root}/log/unicorn_error.log" old_pid = pid_file + '.oldbin' timeout 30 worker_processes 10 # ????? ???? ? ??????????? ?? ????????, ???????? ??????? ? ??????? ???? ???? listen socket_file, :backlog => 1024 pid pid_file stderr_path err_log stdout_path log_file preload_app true GC.copy_on_write_friendly = true if GC.respond_to?(:copy_on_write_friendly=) before_exec do |server| ENV["BUNDLE_GEMFILE"] = "#{rails_root}/Gemfile" end before_fork do |server, worker| defined?(ActiveRecord::Base) and ActiveRecord::Base.connection.disconnect! if File.exists?(old_pid) && server.pid != old_pid begin Process.kill("QUIT", File.read(old_pid).to_i) rescue Errno::ENOENT, Errno::ESRCH end end end after_fork do |server, worker| defined?(ActiveRecord::Base) and ActiveRecord::Base.establish_connection end Also im added capistrano to the project deploy.rb # encoding: utf-8 require 'capistrano/ext/multistage' require 'rvm/capistrano' require 'bundler/capistrano' set :stages, %w(staging production) set :default_stage, "staging" default_run_options[:pty] = true ssh_options[:paranoid] = false ssh_options[:forward_agent] = true set :scm, "git" set :user, "ruby" set :runner, "ruby" set :use_sudo, false set :deploy_via, :remote_cache set :rvm_ruby_string, '1.9.2' # Create uploads directory and link task :configure, :roles => :app do run "cp #{shared_path}/config/database.yml #{release_path}/config/database.yml" # run "ln -s #{shared_path}/db/sphinx #{release_path}/db/sphinx" # run "ln -s #{shared_path}/config/unicorn.rb #{release_path}/config/unicorn.rb" end namespace :deploy do task :restart do run "if [ -f #{unicorn_pid} ] && [ -e /proc/$(cat #{unicorn_pid}) ]; then kill -s USR2 `cat #{unicorn_pid}`; else cd #{deploy_to}/current && bundle exec unicorn_rails -c #{unicorn_conf} -E #{rails_env} -D; fi" end task :start do run "cd #{deploy_to}/current && bundle exec unicorn_rails -c #{unicorn_conf} -E #{rails_env} -D" end task :stop do run "if [ -f #{unicorn_pid} ] && [ -e /proc/$(cat #{unicorn_pid}) ]; then kill -QUIT `cat #{unicorn_pid}`; fi" end end before 'deploy:finalize_update', 'configure' after "deploy:update", "deploy:migrate", "deploy:cleanup" require './config/boot' nginx.conf in app shared path upstream staging_whotracker { server unix:/home/ruby/apps/staging.whotracker.com/shared/sockets/.sock; } server { listen 209.105.242.45; server_name beta.whotracker.com; rewrite ^/(.*) http://www.beta.whotracker.com/$1 permanent; } server { listen 209.105.242.45; server_name www.beta.hotracker.com; root /home/ruby/apps/staging.whotracker.com/current/public; location ~ ^/sitemaps/ { root /home/ruby/apps/staging.whotracker.com/current/system; if (!-f $request_filename) { break; } if (-f $request_filename) { expires -1; break; } } # cache static files :P location ~ ^/(images|javascripts|stylesheets)/ { root /home/ruby/apps/staging.whotracker.com/current/public; if ($query_string ~* "^[0-9a-zA-Z]{40}$") { expires max; break; } if (!-f $request_filename) { break; } } if ( -f /home/ruby/apps/staging.whotracker.com/shared/offline ) { return 503; } location /blog { index index.php index.html index.htm; try_files $uri $uri/ /blog/index.php?q=$uri; } location ~ \.php$ { try_files $uri =404; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/php-fastcgi/php-fastcgi.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } location / { proxy_set_header HTTP_REFERER $http_referer; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; # If the file exists as a static file serve it directly without # running all the other rewite tests on it if (-f $request_filename) { break; } if (!-f $request_filename) { proxy_pass http://staging_whotracker; break; } } error_page 502 =503 @maintenance; error_page 500 504 /500.html; error_page 503 @maintenance; location @maintenance { rewrite ^(.*)$ /503.html break; } } unicorn.log executing ["/home/ruby/apps/staging.whotracker.com/shared/bundle/ruby/1.9.1/bin/unicorn_rails", "-c", "/home/ruby/apps/staging.whotracker.com/current/config/unicorn.rb", "-E", "staging", "-D", {5=>#<Kgio::UNIXServer:/home/ruby/apps/staging.whotracker.com/shared/sockets/.sock>}] (in /home/ruby/apps/staging.whotracker.com/releases/20120517114413) I, [2012-05-17T06:43:48.111717 #14636] INFO -- : inherited addr=/home/ruby/apps/staging.whotracker.com/shared/sockets/.sock fd=5 I, [2012-05-17T06:43:48.111938 #14636] INFO -- : Refreshing Gem list worker=0 ready ... master process ready ... reaped #<Process::Status: pid 2590 exit 0> worker=6 ... master complete Deploy goes successfully, but when i try to access beta.whotracker.com or ip-address i get SERVER NOT FOUND error, while others app works great. Nothing shows up in error logs. Can you please point me where is my fault?

  Read the article

• Split Excel worksheet into multiple worksheets based on a column with VBA (Redux)

  - by Ceeder

  I'm rather new to VBA and I've been working with the code generously displayed and explained by Nixda: Split Excel Worksheet... My only challenge is I've been trying desperately to find a way to include the top 3 rows as a title bu it seems to only allow for one. Here's the code have: Dim Titlesheet As Worksheet iCol = 23 '### Define your criteria column strOutputFolder = (Sheets("Operations").Range("D4")) '### <--Define your path of output folder Set ws = ThisWorkbook.ActiveSheet Set rngLast = Columns(iCol).Find("*", Cells(3, iCol), , , xlByColumns, xlPrevious) Set Titlesheet = Sheets("Input") ws.Columns(iCol).AdvancedFilter Action:=xlFilterInPlace, Unique:=True Set rngUnique = Range(Cells(4, iCol), rngLast).SpecialCells(xlCellTypeVisible) If Dir(strOutputFolder, vbDirectory) = vbNullString Then MkDir strOutputFolder For Each strItem In rngUnique If strItem < "" Then Sheets("Input").Select Range("A1:V3").Select Selection.Copy ws.UsedRange.AutoFilter Field:=iCol, Criteria1:=strItem.Value Workbooks.Add Sheets("Sheet1").Select ActiveSheet.PasteSpecial ws.UsedRange.SpecialCells(xlCellTypeVisible).Copy Destination:=[A4] strFilename = strOutputFolder & "\" & strItem ActiveWorkbook.SaveAs Filename:=strFilename, FileFormat:=xlWorkbookNormal ActiveWorkbook.Close savechanges:=False End If Next ws.ShowAllData Is there something I can change to include these lines? Thanks so much, this code provided by Nixda has taught me a great deal!

  Read the article

• Why does rsync spawn multiple processes for me?

  - by Yoga

  I am using the following cron statement to backup from one folder to another folder in the same machine: 19 21 * * * root rsync -ac --delete /source/folder /dest/folder When I use pstree, I see the cron forked three processes +-cron---cron---rsync---rsync---rsync And ps 9972 ? Ds 1:00 rsync -ac --delete /source/folder /dest/folder 9973 ? S 0:29 rsync -ac --delete /source/folder /dest/folder 9974 ? S 0:09 rsync -ac --delete /source/folder /dest/folder Why are three processes? Can I limit to only one?

  Read the article

• Perforce Restore From Multiple Checkpoint Files?

  - by AJ

  Hi all, I am working with a very large (~11GB) checkpoint file and trying to do a -jr (journal restore) operation. About half way through the file, I'm hitting an entry which causes an error to occur. I'm unable to come up with a conventional way to print, edit, and save changes to the offending line. So right now I'm splitting the checkpoint into files of 500k lines each...up to 47 files and counting. My question is, once I have these separate files: Can I run journal restore on each one separately to check for errors? Once fixed, is it necessary to merge them back together again to do my full journal restore? Any other ideas on how to tackle this problem would be appreciated. Thanks in advance, -aj

  Read the article

• Using dnsmasq for accessing multiple nameservers assigned by DHCP

  - by Ash

  At my work desktop running openSUSE 11.4, I have a local network which gets its address, domain (work.site) and nameservers (10.100.1.1, 10.100.1.2) info through DHCP - which get written into /etc/resolv.conf I get to access the internet using the work network, and these 2 nameservers end up returning the entries for any public domain name lookups on the internet. I also have a private VPN that I end up connecting. The nameserver (10.111.1.1) and domain (private.site) are rarely bound to change for this network, but currently they're pushed by the openVPN client into networkmanager, and which also gets merged with the existing /etc/resolv.conf My resolv.conf ultimately ends up looking like this: search private.site work.site nameserver 127.0.0.1 nameserver 10.111.1.1 nameserver 10.100.1.1 As you can see the 2nd nameserver from my work network was pushed out because of the max 3 entry limitations. It is fine still, but would be a problem if that nameserver goes down for maintenance or something. So I found out that dnsmasq could help me here, and hence I setup dnsmasq just as a local DNS resolver without any DHCP support. So right now this is my /etc/dnsmasq.conf: resolv-file=/etc/resolv.conf server=/private.site/10.111.1.1 server=/1.111.10.in-addr.arpa/10.111.1.1 listen-address=127.0.0.1 bind-interfaces log-queries I've made dnsmasq get the list of nameservers from /etc/resolv.conf since NetworkManager seems to be updating this list correctly (for a max of 3 nameservers). I'm able to resolve the host names in both the networks correctly. So these are the questions I have: Is there a way I can make either NetworkManager or dhclient write out the list of nameservers somewhere else which I can make dnsmasq use as resolv-file ? How do I make dnsmasq use certain nameservers as the default for all queries ? Right now I notice that lookups for public domains on the internet are usually sent to both the nameservers - the one on work.site as well as private.site. It would be good if I can limit this only to work.site.

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

• Multiple syslog-ng destination loghosts

  - by pablo808

  I am currently forwarding logs to one remote destination loghost. filter f_windows { program("Security-Audit*"); }; log { source(r_sys); filter(f_windows); destination(d_windows); }; log { source(r_sys); filter (f_windows); destination(d_loghost); }; I would like to forward these logs to two additional remote destination loghost's. The manual defines destination syntax as: destination <identifier> { destination-driver(params); destination-driver(params); ... }; Tried these different configs: Define additional destinations hosts in d_loghost: destination d_loghost { udp("server1" port(514)); udp("server2" port(514)); udp("server3" port(514));}; filter f_windows { program("Security-Audit*"); }; log { source(r_sys); filter (f_windows); destination(d_loghost); }; Define addtional destination hosts in their own d_loghost definitions: destination d_loghost1 { udp("server1" port(514)); destination d_loghost2 { udp("server2" port(514)); destination d_loghost3 { udp("server3" port(514)); filter f_windows { program("Security-Audit*"); }; log { source(r_sys); filter (f_windows); destination(d_loghost1); }; log { source(r_sys); filter (f_windows); destination(d_loghost2); }; log { source(r_sys); filter (f_windows); destination(d_loghost3); }; Both fail unfortuantly, what am I missing? Thanks.

  Read the article

• Use multiple WSGI mount points in Apache with an Nginx reverse proxy

  - by Thomas

  I am trying to set up multiple virtual hosts on the same server with Nginx and Apache and have run into a curious configuration issue. I have nginx is configured with a generic upstream to apache. upstream backend { server 1.1.1.1:8080; } I'm trying to set up multiple subdomains in nginx that hit different mountpoints in apache. Each would act like the following examples. server { listen 80; server_name foo.yoursite.com; location / { proxy_pass http://backend/bar/; include /etc/nginx/proxy.conf; } ... } server { listen 80; server_name delta.yoursite.com; location / { proxy_pass http://backend/gamma/; include /etc/nginx/proxy.conf; } ... } These mountpoints are pointed at django projects, however each of the url entries are coming back prepended with the apache mountpoint path. So, if I called the django url entry for foo.yoursite.com/wiki/biz/, django appears to be returning foo.yoursite.com/bar/wiki/biz/. Similarly, if I call for the url entry for delta.yoursite.com/wiki/biz/, I get delta.yoursite.com/gamma/wiki/biz/. Is there any way get rid of the prefix being returned on the url entries by django and apache?

  Read the article

• Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

  - by franklundy

  Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

  Read the article

• Multiple public IPs through DD-WRT without 1-to-1 NAT

  - by Stephen Touset

  I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

  Read the article

• Assigning multiple IPv6 addresses on a Server

  - by andrewk

  Let me uncover my intent. My host provides hundreds of IPV6 addresses free, but charge for an IPV4 address. I have several sites under one server and I was wondering if I can give each site/domain it's own ipv6 address. Is that even possible? If so how? I've read quite a bit about ipv6 but I do not understand it as clear as I'd like. My main goal is, for each domain/site to have it's own unique IP, so someone can't do a reverse ip look up and see what sites I have on that server. Thanks in advance for the patience.

  Read the article

• Multiple vlans access to shared pbx system

  - by Matt

  I'm new to networking and was looking for some assistance. First off I'm using packet tracer to diagram my scenario as I will be receiving my equipment next week to deploy. Hardware to be used: 2 catalyst 3560 switches all connect to a sonic wall router I have two companies that work in the same office space. I need to keep these companies separate on their own vlan. They will however need to share the phone system. (Packet tracer file uploaded to give those who have the time to see what I put together.) http://dl.dropbox.com/u/86234623/network%20build.pkt Here is my current test scenario: on switch 0 I have: company A on vlan 2 computers 172.16.1.100 and 101 255.255.0.0 FA0/10 FA0/11 company B on vlan 3 computers 172.16.2.102, 255.255.0.0 FA0/12 PBX on a trunk port 172.16.0.5, 255.255.0.0 FA0/5 trunk port on FA0/1 to connect the switches on switch 1 I have: company A on vlan 2 computers 172.16.1.102, 255.255.0.0 company B on vlan 3 computers 172.16.2.100 and 101, 255.255.0.0 trunk port on FA0/1 to connect the switches I can ping the respective computers on the same vlan but cant ping company A to B which is what I want. However neither company can talk (ping) the PBX. Here are the commands I used to configure what I have: switch 0 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 2 int fa0/11 switchport mode access switchport access vlan 2 int fa0/12 switchport mode access switchport access vlan 3 int fa0/5 switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3 Switch 1 en conf t vlan 2 name A vlan 3 name B int fa0/10 switchport mode access switchport access vlan 3 int fa0/11 switchport mode access switchport access vlan 3 int fa0/12 switchport mode access switchport access vlan 2 int fa0/1 (to connect the switches) switchport trunk encapsulation dot1q switchport mode trunk switchport trunk allowed vlan 1-3

  Read the article

• multiple php compiler on single apache installation

  - by getmizanur

  elloo, i have some old php scripts which runs on php-5.2.x and the current server has php-5.3.x. to get around this problem,i have got two options one is to downgrade php-5.3.x or install php-5.2.x and php-5.3.x at the same time where php-5.2.x serve cgi script. i have decided go for the second option i have followed this tutorial and i can get most of it working however except execution of shell script which selects php-cgi version. i cannot get apache to execute this script. how do i get apache to execute #!/bin/sh # you can change the PHP version here. version="5.2.6" # php.ini file location, */php-5.2.6/lib equals */php-5.2.6/lib/php.ini. PHPRC=/etc/php/phpfarm/inst/php-${version}/lib/php.ini export PHPRC PHP_FCGI_CHILDREN=3 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=5000 export PHP_FCGI_MAX_REQUESTS # which php-cgi binary to execute exec /etc/php/phpfarm/inst/php-${version}/bin/php-cgi my apache vhost.conf <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 </Directory> </VirtualHost> can some one tell me what am i doing wrong? thanks in advance. solution: if i did a2dismod php5 then the above configuration worked. when a2enmod php5 had been activated, apache was executing php5.3 instead of php5.2 even after telling apache to execute php5.2 shell script. to solve my problem, i had to change my virtualhost configuration <VirtualHost *:80> ServerName 526.localhost DocumentRoot /home/getmizanur/public_html/www DirectoryIndex index.php <Directory "/home/getmizanur/public_html/www"> AddHandler php-cgi .php Action php-cgi /php-fcgi/php-cgi-5.2.6 <FilesMatch "\.php"> SetHandler php-cgi </FilesMatch> </Directory> </VirtualHost> presto, it started working.

  Read the article

• How to host multiple mail domains with courier?

  - by Dave Vogt

  I had my server set up with generic aliases in /etc/courier/aliases/users, which worked fine. But today I wanted to host some new domains, where addresses overlap. What I need is that [email protected] goes to account "dv", but [email protected] goes to account "d2". So I set up a new file containing fully qualified addresses ([email protected]: dv) instead of the previous dave: dv. But somehow, courier-smtpd doesn't accept mail to these addresses anymore. makealiases -dump prints all the aliases the way they should be.. so i'm a bit stuck.

  Read the article

• HP Procurve Issue Passing Multiple VLANs over a link

  - by MichaelRwat

  Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2910-24 port switch. This switch is then (Cisco Trunking) to a 2626 switch passing vlan (1 untagged and 100 tagged)between them. I created SVI's on each of the switches for both VLAN's for testing purposes. I can not get vlan 100 to pass across this link. I also have trunks configured to AP's off of the switch and can not ping the vlan 100 BVI on the AP's but can reach the vlan 1 BVI. Port 25 on Access layer (2626) connects (trunks) with port A1 of 2610. STP is not running at all on any switch (this is not my network I can't change this nor did I design this) Distribution Sw: MP1-0# show run ip default-gateway 10.100.100.100 vlan 1 name "DATA" untagged 1-22,24-A1,B1 ip address 10.100.100.6 255.255.255.0 no untagged 23 exit vlan 100 name "GUEST" untagged 23 tagged 24-A1 ip address 10.100.102.6 255.255.255.0 exit Access Sw: ip default-gateway 10.100.100.100 vlan 1 name "DEFAULT_VLAN" untagged 1-26 ip address 10.100.100.5 255.255.255.0 exit vlan 100 name "GUEST" ip address 10.100.102.5 255.255.255.0 tagged 15,25 exitt From the ASA I can ping the vlan 100 address of the 2610 but not the 2626 (10.100.102.6)[Not passing the "trunk"] If I plug into an access port vlan 100 of the 2626 I can ping the SVI for vlan 100 as intended. I can not ping across the "trunk" over vlan 100 but I can across vlan 1. There may be something obvious I'm missing but please review my configuration and thank you for the assistance.

  Read the article

• How do I host multiple independent, secured SharePoint sites (WSS 3.0) without using Active Director

  - by Kyle Noland

  I have a SharePoint site set up on one of my networks to service Active Directory users. To be clear, this is a Windows SharePoint Services 3.0 installation running on Windows Server 2003 Standard. It is not an option to upgrade the server or SharePoint version. Management would like to create several new sites, one for each of a handful of clients. These sites will be used like "dropboxes" or FTP sites so that my company can make large files available to outside contacts, and vice versa. Here are my requirements: I do not want to have to create Active Directory accounts for each external contact. If possible, I would like to store the external usernames and passwords in a database that I can write a small GUI for so that management can handle adding their own external contacts. Each client site must be sandboxed from each other and from my main company SharePoint site. I would like to keep everything running on port 80 and be able to access the sites as either clientname.mycompany.com or www.mycompany.com/clientname If anybody has ever done this I would really appreciate hearing about any lessons you learned and suggestions for how to set this up. Kyle

  Read the article

• Sonicwall with failover, multiple subnets, and preferred WAN interface per subnet

  - by Dan

  I am trying to set up my Sonicwall TZ-210 as follows: Two WAN interfaces (different ISPs), set up in failover mode. Two LAN interfaces with different subnets Each LAN subnet will have a preferred outbound WAN interface, but would failover when necessary. In this way, each ISP is being used for a separate subnet of my network, but both subnets could failover to the other ISP if their primary went down. I know how to do 1 and 2, but I don't know how to do 3. I could set up a route for each subnet to go through a specific interface, but what would happen in the event of a failover? Would it automatically update those routes? Thanks!

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >