Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 98/114 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

  • PPTP VPN on Server 2008 Enterprise

    - by Mike K
    I asked this question on Server fault and was told that was not allowed so im moving it here. I am running Windows Server 2008 enterprise in my HOME network inside of vmware workstation. I am running this on my home network to setup a PPTP VPN connection at home. I have correctly setup everything I needed to make it work, including opening all the ports, 1723 and 43 (GRE). I am able to connect just fine, but when I connect I dont have internet unless I uncheck use remote gateway. The thing is, I want to use the remote gateway to route all my traffic through that connection. Can someone tell me why this isnt working and how to get it to work. When I have remote gateway checked, and I do an ipconfig I dont get a remote gateway for the VPN connection, its 0.0.0.0 when id assume if connected properly should be 192.168.1.254 (my ATT Home Router). Also, if I cant get the remote gateway issue to work, and I have to uncheck that box to get internet, does this mean my VPN session is no longer encrypted? I am fully aware the PPTP VPN is the weakest VPN encryption out there but still having that extra layer of security when im on an unsecure wifi connection makes me feel a bit better. Thank you for all your help in advance. Someone told me I need to setup a gateway or router configured on the server. If thats the case, how go I go about telling the remote co

    Read the article

  • My Ubuntu 10.04 server kills all WAN bandwidth when it's attached to my LAN. Where do you begin troubleshooting?

    - by rrc7cz
    First I should say that my Linux knowledge is minimal; just enough to set up some servers (Apache, Tomcat, Couch, etc). I built a MiniITX server to host some simple sites, act as an SSH tunnel while I'm away, and act as a torrent server. It was not properly secured for a long time (iptables was empty, all ports open, no firewall) though my router did not have much port forwarding set up beyond HTTP, FTP, and SSH. A week or two ago my bandwidth at home dropped from around 27Mbps to 2Mbps and my upload went from 7Mbps to 0.06Mbps. When I unplug the server from the LAN, by bandwidth shoots back up. I threw up a restrictive iptables, removed most of the port forwarding, and checked my router logs to see if there were any open connections from the server (malware?) but there were none. What would you do? What are the first things you'd check? I can of course reinstall everything from scratch, but I'd like to find the root cause.

    Read the article

  • Is it possible (and how if it is) dump two concatenaded disks in a new disk using DD?

    - by pedromarce
    Hi, I have a Lacie enclosure that has a setup with 2 500gb disks configured as 1 drive of 1TB, the only partition created for the whole drive is HFS+ journaled, but the controller in the enclosure is gone and so the drive refuses to mount anymore. I have been able to remove those two disks from the enclosure and connect them using USB ports and a program called R-studio (Raid recovery program) check that the setup the controller in the enclosure was using was both disks concatenated (Not Striped). And so configuring that option in R-studio I could be able to get back all the information. But before I got a license for r-studio for just one use, I would rather buying a new 1TB disk and try to write all the information of those two disks in this new one. I can use Mac or linux machines to do it, and I think it should be ok use DD command in linux to concatenate those two drives into the new one in the right order to get it working again in the new disk and I will reformat the old ones, but I am not sure. So, is it possible in this scenario to write both disks into a new one using DD? Any hints how the command would look? Thanks,

    Read the article

  • How to turn a DSL wireless modem to a wifi hub

    - by my_question
    I used to use DSL for my home internet and used Qwest Q1000 wireless modem. Now I switched to cable and use wireless router to cover the home. One problem is I just bought a desktop and I like to put it in a place far away from the router. The desktop only has cable interface, it does not receive wifi. The obvious solution is I go buy that little USB dongle which can receive wifi and plug it to the desktop. But before doig that, I am wondering if somehow I can re-use the Q1000 modem. The modem has 4 LAN ports and it has wifi antenna. I tried connecting the desktop to Q1000's LAN port, the system shows wire connection is in place, but I cannot access internet. It seems to me Q1000's wifi function is to broadcast the wifi signal out instead of receiving signal. I went to the Q1000 configuration page by going to web page of "192.168.0.1", it is not clear how to set it up. I also wonder one thing, my home wifi is encrypted, so if I want to let Q1000 to join the wifi, I need to somehow type in the password, I am not sure how to do that either. Anyway, maybe this thing cannot be used in this fashion. If you have any suggestion, please shed some light. Thanks.

    Read the article

  • Cannot browse Visual SVN Repositories

    - by user1783560
    I went through Unable to browse repository after setting visual SVN Server and tried to implement the answer suggested but even the IP address is not solving my problem. I have 1) Turned off firewall 2) Set the directory C:\Program Files (x86)\VisualSVN Server security rights to "full control" for all groups including "Network service" group. 3) Set the directory D:\Repositories security rights to "full control" for most groups including "Network service" group. 4) Tried switching between secure and non-secure connection option in visual svn server manager. 5) Tried different with port numbers. Including 443 (with https) and 80 (http). Also tried giving random ports with/without https. Using computer name/ IP address in the url doesn't help. Windows network diagnostics - Troubleshooting report has following message for me. Security policy settings or firewall settings on this computer might be blocking the connection. = Detected Can someone guide me please? I have spent more than two weeks on this now without any solution. Thanks in advance! I appreciate your responses.

    Read the article

  • Private subnet for VM server host-only network

    - by Derek Pressnall
    At my current job, we distribute a product based on a Linux server with multiple VMs defined (using KVM / libvirt). We are planning to expose limited ports to the customer's network, and use iptables to direct inbound traffic to the appropriate internal VM. My question: is there a class of private subnets that I can use for the internal host-only network that is least likely to conflict with a client IP subnet? Specifically, if I choose a /24 out of any of the RFC-1918 defined private subnets (such as 192.168.x.x), there is a chance of conflicting with a customer-used range. I noticed that several current VM implementations default to 192.168.122.x -- is this due to an RFC that I'm not familiar with, and therefore this is a safe range to use (that most network admins would avoid)? Or did the various VM vendors just pick that range randomly? I guess I'm looking for an IP range that is more private than the existing private (RFC1918) addresses. The only other thought I had was to use one of the "Test Net" IP ranges reserved for documentation purposes (RFC 5737). Note, that I'm not worried about a customer's network blocking these IPs, as this is only internal to our server (packets get NATted before leaving the box). However this does seem more unorthodox than just sticking with the default 192.168.122.x/24 subnet.

    Read the article

  • How do I change the default ftp folder in Mac OS X 10.6?

    - by Wild_Eep
    I'm running WordPress 2.9.1 from a Mac running 10.6.3. WordPress is installed to the /Library/WebServer/Documents folder. WordPress has a feature called Auto Update. Clicking an auto update button will download and install updated versions of the WordPress software, or third-party plugin tools. It's a convenient way to keep things up to date. WordPress uses FTP to download the files. I've enabled FTP and set up a user account and opened the requisite ports in my firewall for FTP traffic. This doesn't seem to be enough for my self-hosted installation, though. I'm sure this feature was originally designed for someone who has access to a remote shared webserver, and that it's merely a configuration challenge related to the FTP setup. I feel that if I can adjust the initial directory that the FTP service presents to the AutoUpdate feature, everything else will work properly. So, my question is, how do I adjust what folder is presented when a given user connects to a Mac running 10.6.3 via FTP?

    Read the article

  • Domain name is bringing up wrong site

    - by daniel0mullins
    I have a VPS that hosts several domains. I have set up Apache in the following manner: First VirtualHost /etc/apache2/sites-available/somedomain.com <VirtualHost somedomain.com:80> ServerName somedomain.com ServerAlias www.somedomain.com ... </VirtualHost> Second VirtualHost /etc/apache2/sites-available/someotherdomain.com <VirtualHost someotherdomain.com:80> ServerName someotherdomain.com ServerAlias www.someotherdomain.com ... </VirtualHost> Then I symlink the config files from sites-available to sites-enabled and all is well. I had a need to 'turn off' someotherdomain.com, so I removed the symlink to /etc/apache2/sites-available/someotherdomain.com from sites-enabled and the site no longer shows up... BUT typing someotherdomain.com into a web browser brings up somedomain.com!!! I need it to not resolve at all. Does somethiing need to be done in the VirtualHost to just automatically return a 500 or something along those lines. I really don't want people to reach one website from a different domain. Thanks! EDIT ports.conf looks like this NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> NameVirtualHost *:443 Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule>

    Read the article

  • Solaris OpenStack Horizon customizations

    - by GirishMoodalbail-Oracle
    In Oracle Solaris OpenStack Havana, we have customized the Horizon BUI by modifying existing dashboard and panels to reflect only those features that we support. The modification mostly involves:  --  disabling an widget (checkbox, button, textarea, and so on) --  removal of a tab from a panel --  removal of options from pull-down menus The following table lists the customizations that we have made. |-----------------------------+-----------------------------------------------------| | Where                       | What                                                | |-----------------------------+-----------------------------------------------------| | Project => Instances =>     | Post-Creation tab is removed.                       | | Launch Instance             |                                                     | |                             |                                                     | | Project => Instances =>     | Security Groups tab is removed.                     | | Actions => Edit Instance    |                                                     | |                             |                                                     | | Project => Instances =>     | Console tab is removed.                             | | Instance Name               |                                                     | |                             |                                                     | | Project => Instances =>     | Following actions Console, Edit Security Groups,    | | Actions                     | Pause Instance, Suspend Instance, Resize Instance,  | |                             | Rebuild Instance, and Migrate Instance are removed. | |                             |                                                     | | Project =>                  | Security Groups tab is removed.                     | | Access and Security         |                                                     | |                             |                                                     | | Project =>                  | Create Volume action is removed.                    | | Images and Snapshots =>     |                                                     | | Images => Actions           |                                                     | |                             |                                                     | | Project => Networks =>      | Admin State is disabled and its value is always     | | Create Network              | true.                                               | |                             |                                                     | | Project => Networks =>      | Disable Gateway checkbox is disabled, and its       | | Create Network =>           | value is always false.                              | | Subnet                      |                                                     | |                             |                                                     | | Project => Networks =>      | Allocation Pools and Host Routes text area are      | | Create Network =>           | disabled.                                      | | Subnet Detail               |                                                     | |                             |                                                     | | Project => Networks =>      | Edit Subnet action is removed.                      | | Network Name => Subnet =>   |                                                     | | Actions                     |                                                     | |                             |                                                     | | Project => Networks =>      | Edit Port action is removed.                        | | Network Name => Ports =>    |                                                     | | Actions                     |                                                     | |                             |                                                     | | Admin => Instnaces =>       | Following actions Console, Pause Instance,          | | Actions                     | Suspend Instance, and Migrate Instance are removed. | |                             |                                                     | | Admin => Networks =>        | Edit Network action is removed                      | | Actions                     |                                                     | |                             |                                                     | | Admin => Networks =>         | Edit Subnet action is removed                       | | Subnets => Actions          |                                                     | |                             |                                                     | | Admin => Networks =>         | Edit Port action is removed                         | | Ports => Actions            |                                                     | |                             |                                                     | | Admin => Networks =>         | Admin State and Shared check box are disabled.      | | Create Network              | Network's Admin State is always true, and Shared is | |                             | always false.                                       | |                             |                                                     | | Admin => Networks =>        | Admin State check box is disabled and its value     | | Network Name => Create Port | is always true.                                     | |-----------------------------+-----------------------------------------------------|

    Read the article

  • unexplainable packet drops with 5 ethernet NICs and low traffic on Ubuntu

    - by jon
    I'm stuck on problem where my machine started to drops packets with no sign of ANY system load or high interrupt usage after an upgrade to Ubuntu 12.04. My server is a network monitoring sensor, running Ubuntu LTS 12.04, it passively collects packets from 5 interfaces doing network intrusion type stuff. Before the upgrade I managed to collect 200+GB of packets a day while writing them to disk with around 0% packet loss depending on the day with the help of CPU affinity and NIC IRQ to CPU bindings. Now I lose a great deal of packets with none of my applications running and at very low PPS rate which a modern workstation NIC would have no trouble with. Specs: x64 Xeon 4 cores 3.2 Ghz 16 GB RAM NICs: 5 Intel Pro NICs using the e1000 driver (NAPI). [1] eth0 and eth1 are integrated NICs (in the motherboard) There are 2 other PCI-X network cards, each with 2 Ethernet ports. 3 of the interfaces are running at Gigabit Ethernet, the others are not because they're attached to hubs. Specs: [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm uptime 17:36:00 up 1:43, 2 users, load average: 0.00, 0.01, 0.05 # uname -a Linux nms 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I also have the CPU governor set to performance mode and irqbalance off. The problem still occurs with them on. # lspci -t -vv -[0000:00]-+-00.0 Intel Corporation E7520 Memory Controller Hub +-02.0-[01-03]--+-00.0-[02]----0e.0 Dell PowerEdge Expandable RAID controller 4 | \-00.2-[03]-- +-04.0-[04]-- +-05.0-[05-07]--+-00.0-[06]----07.0 Intel Corporation 82541GI Gigabit Ethernet Controller | \-00.2-[07]----08.0 Intel Corporation 82541GI Gigabit Ethernet Controller +-06.0-[08-0a]--+-00.0-[09]--+-04.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | | \-04.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-00.2-[0a]--+-02.0 Digium, Inc. Wildcard TE210P/TE212P dual-span T1/E1/J1 card 3.3V | +-03.0 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) | \-03.1 Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) +-1d.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 +-1d.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 +-1d.2 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 +-1d.7 Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller +-1e.0-[0b]----0d.0 Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] +-1f.0 Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge \-1f.1 Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller I believe the NIC nor the NIC drivers are dropping the packets because ethtool reports 0 under rx_missed_errors and rx_no_buffer_count for each interface. On the old system, if it couldn't keep up this is where the drops would be. I drop packets on multiple interfaces just about every second, usually in small increments of 2-4. I tried all these sysctl values, I'm currently using the uncommented ones. # cat /etc/sysctl.conf # high net.core.netdev_max_backlog = 3000000 net.core.rmem_max = 16000000 net.core.rmem_default = 8000000 # defaults #net.core.netdev_max_backlog = 1000 #net.core.rmem_max = 131071 #net.core.rmem_default = 163480 # moderate #net.core.netdev_max_backlog = 10000 #net.core.rmem_max = 33554432 #net.core.rmem_default = 33554432 Here's an example of an interface stats report with ethtool. They are all the same, nothing is out of the ordinary ( I think ), so I'm only going to show one: ethtool -S eth2 NIC statistics: rx_packets: 7498 tx_packets: 0 rx_bytes: 2722585 tx_bytes: 0 rx_broadcast: 327 tx_broadcast: 0 rx_multicast: 1504 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 1504 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 0 tx_tcp_seg_failed: 0 rx_flow_control_xon: 0 rx_flow_control_xoff: 0 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 2722585 rx_csum_offload_good: 0 rx_csum_offload_errors: 0 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 01 # ifconfig eth0 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:373348 errors:16 dropped:95 overruns:0 frame:16 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:356830572 (356.8 MB) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:11:43:e0:e2:8d UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:13616 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8690528 (8.6 MB) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 00:04:23:e1:77:6a UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:7750 errors:0 dropped:471 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2780935 (2.7 MB) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 00:04:23:e1:77:6b UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:5112 errors:0 dropped:206 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:639472 (639.4 KB) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 00:04:23:b6:35:6c UP BROADCAST RUNNING NOARP PROMISC ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:961467 errors:0 dropped:935 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:958561305 (958.5 MB) TX bytes:0 (0.0 B) eth5 Link encap:Ethernet HWaddr 00:04:23:b6:35:6d inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4264 errors:0 dropped:16 overruns:0 frame:0 TX packets:699 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:572228 (572.2 KB) TX bytes:124456 (124.4 KB) I tried the defaults, then started to play around with settings. I wasn't using any flow control and I increased the RxDescriptor count to 4096 before the upgrade as well without any problems. # cat /etc/modprobe.d/e1000.conf options e1000 XsumRX=0,0,0,0,0 RxDescriptors=4096,4096,4096,4096,4096 FlowControl=0,0,0,0,0 debug=16 Here's my network configuration file, I turned off checksumming and various offloading mechanisms along with setting CPU affinity with heavy use interfaces getting an entire CPU and light use interfaces sharing a CPU. I used these settings prior to the upgrade without problems. # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet manual pre-up /sbin/ethtool -G eth0 rx 4096 tx 0 pre-up /sbin/ethtool -K eth0 gro off gso off rx off pre-up /sbin/ethtool -A eth0 rx off autoneg off up ifconfig eth0 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/48/smp_affinity down ifconfig eth0 down post-down /sbin/ethtool -G eth0 rx 256 tx 256 post-down /sbin/ethtool -K eth0 gro on gso on rx on post-down /sbin/ethtool -A eth0 rx on autoneg on auto eth1 iface eth1 inet manual pre-up /sbin/ethtool -G eth1 rx 4096 tx 0 pre-up /sbin/ethtool -K eth1 gro off gso off rx off pre-up /sbin/ethtool -A eth1 rx off autoneg off up ifconfig eth1 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/49/smp_affinity down ifconfig eth1 down post-down /sbin/ethtool -G eth1 rx 256 tx 256 post-down /sbin/ethtool -K eth1 gro on gso on rx on post-down /sbin/ethtool -A eth1 rx on autoneg on auto eth2 iface eth2 inet manual pre-up /sbin/ethtool -G eth2 rx 4096 tx 0 pre-up /sbin/ethtool -K eth2 gro off gso off rx off pre-up /sbin/ethtool -A eth2 rx off autoneg off up ifconfig eth2 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "1" > /proc/irq/82/smp_affinity down ifconfig eth2 down post-down /sbin/ethtool -G eth2 rx 256 tx 256 post-down /sbin/ethtool -K eth2 gro on gso on rx on post-down /sbin/ethtool -A eth2 rx on autoneg on auto eth3 iface eth3 inet manual pre-up /sbin/ethtool -G eth3 rx 4096 tx 0 pre-up /sbin/ethtool -K eth3 gro off gso off rx off pre-up /sbin/ethtool -A eth3 rx off autoneg off up ifconfig eth3 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "2" > /proc/irq/83/smp_affinity down ifconfig eth3 down post-down /sbin/ethtool -G eth3 rx 256 tx 256 post-down /sbin/ethtool -K eth3 gro on gso on rx on post-down /sbin/ethtool -A eth3 rx on autoneg on auto eth4 iface eth4 inet manual pre-up /sbin/ethtool -G eth4 rx 4096 tx 0 pre-up /sbin/ethtool -K eth4 gro off gso off rx off pre-up /sbin/ethtool -A eth4 rx off autoneg off up ifconfig eth4 0.0.0.0 -arp promisc mtu 1500 allmulti txqueuelen 0 up post-up echo "4" > /proc/irq/77/smp_affinity down ifconfig eth4 down post-down /sbin/ethtool -G eth4 rx 256 tx 256 post-down /sbin/ethtool -K eth4 gro on gso on rx on post-down /sbin/ethtool -A eth4 rx on autoneg on auto eth5 iface eth5 inet static pre-up /etc/fw.conf address 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 192.168.1.2 192.168.1.3 up ifconfig eth5 up post-up echo "8" > /proc/irq/77/smp_affinity down ifconfig eth5 down Here's a few examples of packet drops, i ran one after another, probabling totaling 3 or 4 seconds. You can see increases in the drops from the 1st and 3rd. This was a non-busy time, very little traffic. # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 505 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 225 lo: 0 eth2: 507 eth1: 0 eth5: 17 eth0: 105 eth4: 1034 # awk '{ print $1,$5 }' /proc/net/dev Inter-| face drop eth3: 227 lo: 0 eth2: 512 eth1: 0 eth5: 17 eth0: 105 eth4: 1039 I tried the pci=noacpi options. With and without, it's the same. This is what my interrupt stats looked like before the upgrade, after, with ACPI on PCI it showed multiple NICs bound to an interrupt and shared with other devices such as USB drives which I didn't like so I think i'm going to keep it with ACPI off as it's easier to designate sole purpose interrupts. Is there any advantage I would have using the default i.e. ACPI w/ PCI. ? # cat /etc/default/grub | grep CMD_LINE GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 noacpi pci=noacpi" GRUB_CMDLINE_LINUX="" # cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 0: 45 0 0 16 IO-APIC-edge timer 1: 1 0 0 7936 IO-APIC-edge i8042 2: 0 0 0 0 XT-PIC-XT-PIC cascade 6: 0 0 0 3 IO-APIC-edge floppy 8: 0 0 0 1 IO-APIC-edge rtc0 9: 0 0 0 0 IO-APIC-edge acpi 12: 0 0 0 1809 IO-APIC-edge i8042 14: 1 0 0 4498 IO-APIC-edge ata_piix 15: 0 0 0 0 IO-APIC-edge ata_piix 16: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb2 18: 0 0 0 1350 IO-APIC-fasteoi uhci_hcd:usb4, radeon 19: 0 0 0 0 IO-APIC-fasteoi uhci_hcd:usb3 23: 0 0 0 4099 IO-APIC-fasteoi ehci_hcd:usb1 38: 0 0 0 61963 IO-APIC-fasteoi megaraid 48: 0 0 1002319 4 IO-APIC-fasteoi eth0 49: 0 0 38772 3 IO-APIC-fasteoi eth1 77: 0 0 130076 432159 IO-APIC-fasteoi eth4 78: 0 0 0 23917 IO-APIC-fasteoi eth5 82: 1329033 0 0 4 IO-APIC-fasteoi eth2 83: 0 4886525 0 6 IO-APIC-fasteoi eth3 NMI: 5 6 4 5 Non-maskable interrupts LOC: 61409 57076 64257 114764 Local timer interrupts SPU: 0 0 0 0 Spurious interrupts IWI: 0 0 0 0 IRQ work interrupts RES: 17956 25333 13436 14789 Rescheduling interrupts CAL: 22436 607 539 478 Function call interrupts TLB: 1525 1458 4600 4151 TLB shootdowns TRM: 0 0 0 0 Thermal event interrupts THR: 0 0 0 0 Threshold APIC interrupts MCE: 0 0 0 0 Machine check exceptions MCP: 16 16 16 16 Machine check polls ERR: 0 MIS: 0 Here's sample output of vmstat, showing the system. Barebones system right now. root@nms:~# vmstat -S m 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 14992 192 1029 0 0 56 2 419 29 1 0 99 0 0 0 0 14992 192 1029 0 0 0 0 922 27 0 0 100 0 0 0 0 14991 192 1029 0 0 0 36 763 50 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 646 35 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 722 54 0 0 100 0 0 0 0 14991 192 1029 0 0 0 0 793 27 0 0 100 0 ^C Here's dmesg output. I can't figure out why my PCI-X slots are negotiated as PCI. The network cards are all PCI-X with the exception of the integrated NICs that came with the server. In the output below it looks as if eth3 and eth2 negotiated at PCI-X speeds rather than PCI:66Mhz. Wouldn't they all drop to PCI:66Mhz? If your integrated NICs are PCI, as labeled below (eth0,eth1), then wouldn't all devices on your bus speed drop down to that slower bus speed? If not, I still don't know why only one of my NICs ( each has two ethernet ports) is labeled as PCI-X in the output below. Does that mean it is running at PCI-X speeds are is it showing that it's capable? # dmesg | grep e1000 [ 3678.349337] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 3678.349342] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3678.349394] e1000 0000:06:07.0: PCI->APIC IRQ transform: INT A -> IRQ 48 [ 3678.409725] e1000 0000:06:07.0: Receive Descriptors set to 4096 [ 3678.409730] e1000 0000:06:07.0: Checksum Offload Disabled [ 3678.409734] e1000 0000:06:07.0: Flow Control Disabled [ 3678.586409] e1000 0000:06:07.0: eth0: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8c [ 3678.586419] e1000 0000:06:07.0: eth0: Intel(R) PRO/1000 Network Connection [ 3678.586642] e1000 0000:07:08.0: PCI->APIC IRQ transform: INT A -> IRQ 49 [ 3678.649854] e1000 0000:07:08.0: Receive Descriptors set to 4096 [ 3678.649859] e1000 0000:07:08.0: Checksum Offload Disabled [ 3678.649863] e1000 0000:07:08.0: Flow Control Disabled [ 3678.826436] e1000 0000:07:08.0: eth1: (PCI:66MHz:32-bit) 00:11:43:e0:e2:8d [ 3678.826444] e1000 0000:07:08.0: eth1: Intel(R) PRO/1000 Network Connection [ 3678.826627] e1000 0000:09:04.0: PCI->APIC IRQ transform: INT A -> IRQ 82 [ 3679.093266] e1000 0000:09:04.0: Receive Descriptors set to 4096 [ 3679.093271] e1000 0000:09:04.0: Checksum Offload Disabled [ 3679.093275] e1000 0000:09:04.0: Flow Control Disabled [ 3679.130239] e1000 0000:09:04.0: eth2: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6a [ 3679.130246] e1000 0000:09:04.0: eth2: Intel(R) PRO/1000 Network Connection [ 3679.130449] e1000 0000:09:04.1: PCI->APIC IRQ transform: INT B -> IRQ 83 [ 3679.397312] e1000 0000:09:04.1: Receive Descriptors set to 4096 [ 3679.397318] e1000 0000:09:04.1: Checksum Offload Disabled [ 3679.397321] e1000 0000:09:04.1: Flow Control Disabled [ 3679.434350] e1000 0000:09:04.1: eth3: (PCI-X:133MHz:64-bit) 00:04:23:e1:77:6b [ 3679.434360] e1000 0000:09:04.1: eth3: Intel(R) PRO/1000 Network Connection [ 3679.434553] e1000 0000:0a:03.0: PCI->APIC IRQ transform: INT A -> IRQ 77 [ 3679.704072] e1000 0000:0a:03.0: Receive Descriptors set to 4096 [ 3679.704077] e1000 0000:0a:03.0: Checksum Offload Disabled [ 3679.704081] e1000 0000:0a:03.0: Flow Control Disabled [ 3679.738364] e1000 0000:0a:03.0: eth4: (PCI:33MHz:64-bit) 00:04:23:b6:35:6c [ 3679.738371] e1000 0000:0a:03.0: eth4: Intel(R) PRO/1000 Network Connection [ 3679.738538] e1000 0000:0a:03.1: PCI->APIC IRQ transform: INT B -> IRQ 78 [ 3680.046060] e1000 0000:0a:03.1: eth5: (PCI:33MHz:64-bit) 00:04:23:b6:35:6d [ 3680.046067] e1000 0000:0a:03.1: eth5: Intel(R) PRO/1000 Network Connection [ 3682.132415] e1000: eth0 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.224423] e1000: eth1 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.316385] e1000: eth2 NIC Link is Up 100 Mbps Half Duplex, Flow Control: None [ 3682.408391] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.500396] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 3682.708401] e1000: eth5 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX At first I thought it was the NIC drivers but I'm not so sure. I really have no idea where else to look at the moment. Any help is greatly appreciated as I'm struggling with this. If you need more information just ask. Thanks! [1]http://www.cs.fsu.edu/~baker/devices/lxr/http/source/linux/Documentation/networking/e1000.txt?v=2.6.11.8 [2] http://support.dell.com/support/edocs/systems/pe2850/en/ug/t1390aa.htm

    Read the article

  • .htaccess not working (mod_rewrite)

    - by Mike Curry
    Edit: I am pretty sure my .htaccess file is NOT being executed, and the problem is NOT with my rewrite rules. I have not having any luck getting my .htaccess with mod_rewrite working. Basically all I am trying to do is remove 'www' from "http://www.site.com" and "https://www.site.com". If there is anything I am missing (conf files, etc let me know I willl update this) I jsut can't see whats wrong here... I am using a 1&1 VPS III Virtual private server... anyone ever have this issue? I am using Ubuntu 8.04 Server LTS. Here is my .htaccess file (located @ /var/www/site/trunk/html/) Options +FollowSymLinks RewriteEngine on RewriteCond %{HTTP_HOST} ^www\.(.*) [NC] RewriteRule (.*) //%1/$1 [L,R=301] My mod_rewrite is enabled: The auto regenerated sym link is there in mods-available and /usr/lib/apache2/modules/ contains mod_rewrite.so root@s15348441:/etc/apache2/mods-available# more rewrite.load LoadModule rewrite_module /usr/lib/apache2/modules/mod_rewrite.so root@s15348441:/var/log# apache2ctl -t -D DUMP_MODULES Loaded Modules: core_module (static) log_config_module (static) logio_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) auth_basic_module (shared) authn_file_module (shared) authz_default_module (shared) authz_groupfile_module (shared) authz_host_module (shared) authz_user_module (shared) autoindex_module (shared) cgi_module (shared) dir_module (shared) env_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK My apache config files: apache2.conf # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "/var/log/apache2/foo.log" # with ServerRoot set to "" will be interpreted by the # server as "//var/log/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs-2.1/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # #<IfModule !mpm_winnt.c> #<IfModule !mpm_netware.c> LockFile /var/lock/apache2/accept.lock #</IfModule> #</IfModule> # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 15 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog /var/log/apache2/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf # Include all the user configurations: Include /etc/apache2/httpd.conf # Include ports listing Include /etc/apache2/ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # # ServerTokens # This directive configures what you return as the Server HTTP response # Header. The default is 'Full' which sends information about the OS-Type # and compiled in modules. # Set to one of: Full | OS | Minor | Minimal | Major | Prod # where Full conveys the most information, and Prod the least. # ServerTokens Full # # Optionally add a line containing the server version and virtual host # name to server-generated pages (internal error documents, FTP directory # listings, mod_status and mod_info output etc., but not CGI generated # documents or custom error documents). # Set to "EMail" to also include a mailto: link to the ServerAdmin. # Set to one of: On | Off | EMail # ServerSignature On # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http://www.example.com/subscription_info.html # # # Putting this all together, we can internationalize error responses. # # We use Alias to redirect any /error/HTTP_<error>.html.var response to # our collection of by-error message multi-language collections. We use # includes to substitute the appropriate text. # # You can modify the messages' appearance without changing any of the # default HTTP_<error>.html.var files by adding the line: # # Alias /error/include/ "/your/include/path/" # # which allows you to create your own set of files by starting with the # /usr/share/apache2/error/include/ files and copying them to /your/include/path/, # even on a per-VirtualHost basis. The default include files will display # your Apache version number and your ServerAdmin email address regardless # of the setting of ServerSignature. # # The internationalized error documents require mod_alias, mod_include # and mod_negotiation. To activate them, uncomment the following 30 lines. # Alias /error/ "/usr/share/apache2/error/" # # <Directory "/usr/share/apache2/error"> # AllowOverride None # Options IncludesNoExec # AddOutputFilter Includes html # AddHandler type-map var # Order allow,deny # Allow from all # LanguagePriority en cs de es fr it nl sv pt-br ro # ForceLanguagePriority Prefer Fallback # </Directory> # # ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var # ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var # ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var # ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var # ErrorDocument 405 /error/HTTP_METHOD_NOT_ALLOWED.html.var # ErrorDocument 408 /error/HTTP_REQUEST_TIME_OUT.html.var # ErrorDocument 410 /error/HTTP_GONE.html.var # ErrorDocument 411 /error/HTTP_LENGTH_REQUIRED.html.var # ErrorDocument 412 /error/HTTP_PRECONDITION_FAILED.html.var # ErrorDocument 413 /error/HTTP_REQUEST_ENTITY_TOO_LARGE.html.var # ErrorDocument 414 /error/HTTP_REQUEST_URI_TOO_LARGE.html.var # ErrorDocument 415 /error/HTTP_UNSUPPORTED_MEDIA_TYPE.html.var # ErrorDocument 500 /error/HTTP_INTERNAL_SERVER_ERROR.html.var # ErrorDocument 501 /error/HTTP_NOT_IMPLEMENTED.html.var # ErrorDocument 502 /error/HTTP_BAD_GATEWAY.html.var # ErrorDocument 503 /error/HTTP_SERVICE_UNAVAILABLE.html.var # ErrorDocument 506 /error/HTTP_VARIANT_ALSO_VARIES.html.var # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ My default config file for www on apache NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] #SSLEnable #SSLVerifyClient none #SSLCertificateFile /usr/local/ssl/crt/public.crt #SSLCertificateKeyFile /usr/local/ssl/private/private.key DocumentRoot /var/www/site/trunk/html <Directory /> Options FollowSymLinks AllowOverride all </Directory> <Directory /var/www/site/trunk/html> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My ssl config file NameVirtualHost *:443 <VirtualHost *:443> ServerAdmin [email protected] #SSLEnable #SSLVerifyClient none #SSLCertificateFile /usr/local/ssl/crt/public.crt #SSLCertificateKeyFile /usr/local/ssl/private/private.key DocumentRoot /var/www/site/trunk/html <Directory /> Options FollowSymLinks AllowOverride all </Directory> <Directory /var/www/site/trunk/html> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn SSLEngine On SSLCertificateFile /usr/local/ssl/crt/public.crt SSLCertificateKeyFile /usr/local/ssl/private/private.key CustomLog /var/log/apache2/access.log combined ServerSignature On Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My /etc/apache2/httpd.conf is blank The directory /etc/apache2/conf.d has nothing in it but one file (charset) contents of /etc/apache2/conf.dcharset # Read the documentation before enabling AddDefaultCharset. # In general, it is only a good idea if you know that all your files # have this encoding. It will override any encoding given in the files # in meta http-equiv or xml encoding tags. #AddDefaultCharset UTF-8 My apache error.log [Wed Jun 03 00:12:31 2009] [error] [client 216.168.43.234] client sent HTTP/1.1 request without hostname (see RFC2616 section 14.23): /w00tw00t.at.ISC.SANS.DFind:) [Wed Jun 03 05:03:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:03:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:48 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:13:57 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:17:28 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 05:26:23 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 05:26:34 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 06:03:41 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 06:03:51 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 06:25:07 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 06:25:17 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 12:09:25 2009] [error] [client 61.139.105.163] File does not exist: /var/www/site/trunk/html/fastenv [Wed Jun 03 15:04:42 2009] [notice] Graceful restart requested, doing restart [Wed Jun 03 15:04:43 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations [Wed Jun 03 15:29:51 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:29:54 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:30:32 2009] [error] [client 99.247.237.46] File does not exist: /var/www/site/trunk/html/favicon.ico [Wed Jun 03 15:45:54 2009] [notice] caught SIGWINCH, shutting down gracefully [Wed Jun 03 15:46:05 2009] [notice] Apache/2.2.8 (Ubuntu) PHP/5.2.4-2ubuntu5.6 with Suhosin-Patch mod_ssl/2.2.8 OpenSSL/0.9.8g configured -- resuming normal operations

    Read the article

  • SQLAuthority News – Tips for Traveling to Nepal

    - by pinaldave
    If you are a regular reader of this blog, you might know that I travel nearly 20+ days out of 30 days in a month. There are cases when I don’t have a chance to go home for an entire month and my family has to travel to different cities just to meet me. During my recent visit, one of my acquaintances suggested that I should blog about my travel experiences as well. This can be helpful to others who are traveling to the country or city. I have previously written about my experience about all the airlines in India. I would be writing about a few tips about traveling to the beautiful country Nepal today. Kathmandu, the capital of Nepal is very scenic. There are lots of historical places to see and visit. I was fortunate enough to stopover the Pashupatinath Temple, Bhaktapur, Vasantpur and the temple of Kumari Goddess. I also visited casinos there, but even if  I have stayed in Las Vegas for 3 and a half years before, I was not keen on them so I left the casinos just like what I did in Las Vegas . I also traveled to the famous Thamel area by car. Here are my quick tips for anyone who is planning to visit Nepal. They are not categorized but just written in the order that came to my mind. Please note that if you are an Indian, you will get a special privilege everywhere in Nepal, beginning right from the Indian airports. Use the expression “Nameste!” If you want to greet any Indian or Nepali. Indian Nationals do not need visa/passport to enter Nepal. In fact, Indian Nationals can just walk in to Nepal without any passport; but should have any valid Indian ID. There is no use of a passport since it will not be stamped at any immigration ports, whether in India or Nepal. Indian currency is widely accepted everywhere. However, please bring only Rs. 100 bills/notes as Rs. 500 or Rs. 1000 are not accepted. However, casinos there will accept larger bills. Indian National Language – Hindi is widely spoken and understood everywhere. I did not find a single person who had trouble speaking it. Nepali language uses the scripting language as Devnagari, which is similar to Hindi. Here, you will find food of almost every country.  The taste of Nepali food is authentic and very delicious. It is very safe to travel and move around in Kathmandu (despite what media suggests). However, it will really help if you have a friend who speaks Nepali. You can negotiate a few deals and cut off to almost 1/5 of the original quoted price of products sold here. If you are from Gujarat, India – you will find Nepali language sharing many common words. Temples are everywhere, so do not miss to visit a few of them. Pashupatinath is a must. Only followers of Hindu religion (from Nepal and India only) are allowed in most of the holy places. Camera is allowed everywhere except on the holy places. Now it is your turn to share your opinions or any suggestions. I think Nepal is a great country as there are lots of places to visit. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, T SQL, Technology

    Read the article

  • Oracle Announces Oracle Exadata X3 Database In-Memory Machine

    - by jgelhaus
    Fourth Generation Exadata X3 Systems are Ideal for High-End OLTP, Large Data Warehouses, and Database Clouds; Eighth-Rack Configuration Offers New Low-Cost Entry Point ORACLE OPENWORLD, SAN FRANCISCO – October 1, 2012 News Facts During his opening keynote address at Oracle OpenWorld, Oracle CEO, Larry Ellison announced the Oracle Exadata X3 Database In-Memory Machine - the latest generation of its Oracle Exadata Database Machines. The Oracle Exadata X3 Database In-Memory Machine is a key component of the Oracle Cloud. Oracle Exadata X3-2 Database In-Memory Machine and Oracle Exadata X3-8 Database In-Memory Machine can store up to hundreds of Terabytes of compressed user data in Flash and RAM memory, virtually eliminating the performance overhead of reads and writes to slow disk drives, making Exadata X3 systems the ideal database platforms for the varied and unpredictable workloads of cloud computing. In order to realize the highest performance at the lowest cost, the Oracle Exadata X3 Database In-Memory Machine implements a mass memory hierarchy that automatically moves all active data into Flash and RAM memory, while keeping less active data on low-cost disks. With a new Eighth-Rack configuration, the Oracle Exadata X3-2 Database In-Memory Machine delivers a cost-effective entry point for smaller workloads, testing, development and disaster recovery systems, and is a fully redundant system that can be used with mission critical applications. Next-Generation Technologies Deliver Dramatic Performance Improvements Oracle Exadata X3 Database In-Memory Machines use a combination of scale-out servers and storage, InfiniBand networking, smart storage, PCI Flash, smart memory caching, and Hybrid Columnar Compression to deliver extreme performance and availability for all Oracle Database Workloads. Oracle Exadata X3 Database In-Memory Machine systems leverage next-generation technologies to deliver significant performance enhancements, including: Four times the Flash memory capacity of the previous generation; with up to 40 percent faster response times and 100 GB/second data scan rates. Combined with Exadata’s unique Hybrid Columnar Compression capabilities, hundreds of Terabytes of user data can now be managed entirely within Flash; 20 times more capacity for database writes through updated Exadata Smart Flash Cache software. The new Exadata Smart Flash Cache software also runs on previous generation Exadata systems, increasing their capacity for writes tenfold; 33 percent more database CPU cores in the Oracle Exadata X3-2 Database In-Memory Machine, using the latest 8-core Intel® Xeon E5-2600 series of processors; Expanded 10Gb Ethernet connectivity to the data center in the Oracle Exadata X3-2 provides 40 10Gb network ports per rack for connecting users and moving data; Up to 30 percent reduction in power and cooling. Configured for Your Business, Available Today Oracle Exadata X3-2 Database In-Memory Machine systems are available in a Full-Rack, Half-Rack, Quarter-Rack, and the new low-cost Eighth-Rack configuration to satisfy the widest range of applications. Oracle Exadata X3-8 Database In-Memory Machine systems are available in a Full-Rack configuration, and both X3 systems enable multi-rack configurations for virtually unlimited scalability. Oracle Exadata X3-2 and X3-8 Database In-Memory Machines are fully compatible with prior Exadata generations and existing systems can also be upgraded with Oracle Exadata X3-2 servers. Oracle Exadata X3 Database In-Memory Machine systems can be used immediately with any application certified with Oracle Database 11g R2 and Oracle Real Application Clusters, including SAP, Oracle Fusion Applications, Oracle’s PeopleSoft, Oracle’s Siebel CRM, the Oracle E-Business Suite, and thousands of other applications. Supporting Quotes “Forward-looking enterprises are moving towards Cloud Computing architectures,” said Andrew Mendelsohn, senior vice president, Oracle Database Server Technologies. “Oracle Exadata’s unique ability to run any database application on a fully scale-out architecture using a combination of massive memory for extreme performance and low-cost disk for high capacity delivers the ideal solution for Cloud-based database deployments today.” Supporting Resources Oracle Press Release Oracle Exadata Database Machine Oracle Exadata X3-2 Database In-Memory Machine Oracle Exadata X3-8 Database In-Memory Machine Oracle Database 11g Follow Oracle Database via Blog, Facebook and Twitter Oracle OpenWorld 2012 Oracle OpenWorld 2012 Keynotes Like Oracle OpenWorld on Facebook Follow Oracle OpenWorld on Twitter Oracle OpenWorld Blog Oracle OpenWorld on LinkedIn Mark Hurd's keynote with Andy Mendelsohn and Juan Loaiza - - watch for the replay to be available soon at http://www.youtube.com/user/Oracle or http://www.oracle.com/openworld/live/on-demand/index.html

    Read the article

  • Make Your PC Look Like Windows Phone 7

    - by Matthew Guay
    Windows Phone 7 offers a unique and exciting UI that displays lots of information efficiently on the screen.  And with a simple Rainmeter theme, you can have the same UI and content directly on your Windows 7 desktop. Turn your Desktop into a Windows Phone 7 lookalike To give your Windows 7 desktop a Windows Phone 7 makeover, first you need to have the free Rainmeter application installed.  If you do not have it installed, download it from the link below and run the setup.  Accept the license agreement, and install it with the default settings. By default Rainmeter will automatically run when you start your computer.  If you do not want this, you can uncheck the box during the setup. Now, download the Omnimo UI theme for Rainmeter (link below).  You will need to unzip the folder first. This theme uses the Segoe UI and the Segoe UI Light font, so Windows Vista users need to install the segoeuil.ttf font first, and XP users need to install both the segoeui.ttf and the segoeuil.ttf font first.  Copy the appropriate fonts to C:\Windows\Fonts, or in Vista double-click on the font and select Install. Now, run the Rainmeter theme setup.  Double-click on the Rainstaller.exe in the Omnimo folder. Click Express install to add the theme and skin to Rainmeter. Click Finish, and by default Rainmeter will open with your new theme. When the new theme opens the first time, you will be asked to read the readme, or simply go to the gallery. When you open the gallery, you can choose from a wide variety of tiles and gadgets to place on your desktop.  You can also choose a different color scheme for your tiles. Once you’re done, click the X in the top right hand corner to close the Gallery.  Welcome to your Windows Phone 7 desktop!  Many of the gadgets are dynamic, and you can change the settings for most of them.  The only thing missing is the transition animations that Windows Phone 7 shows when you launch an application. To make it look even more like Windows Phone 7, you can change your background to black.  This makes the desktop theme really dramatic. And, if you want to add gadgets or change the color scheme, simply click on the + logo on the top. Windows Phone 7 Desktop Wallpapers If you’d prefer to simply change your background, My Microsoft Life has several very nice Windows Phone 7 wallpapers available for free.  Click the link below to download these and other Microsoft-centric wallpapers. If you can’t wait to get the new Windows phone 7, this is a great way to start experiencing the beauty of the phone UI on your desktop. Links Download Rainmeter Download the Omnimo UI Rainmeter theme Download Windows Phone 7 inspired wallpapers Similar Articles Productive Geek Tips Try out Windows Phone 7 on your PC todayTest All Features of Windows Phone 7 On Your PCHow-To Geek on Lifehacker: How to Make Windows Vista Less AnnoyingCreate a Shortcut or Hotkey to Mute the System Volume in WindowsMake Ubuntu Automatically Save Changes to Your Session TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Norwegian Life If Web Browsers Were Modes of Transportation Google Translate (for animals) Roadkill’s Scan Port scans for open ports Out of 100 Tweeters Out of band Security Update for Internet Explorer

    Read the article

  • BizTalk 2009 - BizTalk Benchmark Wizard: Installation

    - by StuartBrierley
    As previously detailed, I have completed a single server installation of BizTalk Server 2009 standard on my development laptop; a MacBook Pro Core2Duo running at 2.16Ghz with 2Gb of RAM.  Following this I also posted on my use of the BizTalk Server Best Practices Anaylser and how to configure the BizTalk SQL Server Jobs.  All of which means that I should have some confidence that I have a decent working BizTalk Server 2009 environment, Next I thought that it would be a good idea to try and get some idea of how this setup performs by carrying out some baseline tests that can then be replicated on the test and live servers. The aim of this would be to allow confident predictions to be made of how any solutions developed on a single "server" installation may be expected to perform when deployed to these multi-server BizTalk Server 2009 standard installations. The BizTalk Benchmark Wizard would seem to be the perfect tool for the job. The BizTalk Benchmark Wizard is a ultility that can be used to gain some validation of a BizTalk installation, giving a level of guidance on whether it is performing as might be expected. This utility should be used after BizTalk Server has been installed and before any solutions are deployed to the environment.  This will ensure that you are getting consistent and clean results from the BizTalk Benchmark Wizard. The BizTalk Benchmark Wizard applies load to the BizTalk Server environment under a choice of specific scenarios. During these scenarios performance counter information is collected and assessed against statistics that are appropriate to the BizTalk Server environment: "The executed scenarios may or may not be relative to any realistic scenario, and is only intended for testing. The BizTalk Benchmark Wizard has been developed in relation to the BizTalk Server 2009 Scale Out Testing Study. More information about the study can be found here: http://msdn.microsoft.com/en-us/library/ee377068(BTS.10).aspx" After downloading and installing the wizard you will need set up the Hosts, Instances and Adapter handlers.  This is done by running a script file using the “cscript” detailed below.  To do this you will need to open a command prompt window and navigate to the script folder; assuming the default installation location this would be C:\Program Files\Blogical\BizTalk Benchmark Wizard\Artefacts\BizTalk. In this folder you should find an InstallHosts.vbs file which can be executed using the following parameters: NTGroupName - The name of the Windows NT group. UserName – The name of the user account running the service instances. Password – The password of the user account running the service instances. Receive Host – The name of the server where you want to run the receive host instance.  Send Host - The name of the server where you want to run the sen host instance. Processing Host - The name of the server where you want to run the process host instance. By default the script is set up for 64 bit hosts, so if you are running in 32 bit environment make sure that you change the following line in the script before continuing: from:   objHS.IsHost32BitOnly = False to:    objHS.IsHost32BitOnly = True If you have a single box installation, your script command might look like this: cscript InstallHosts.vbs "BizTalk Application Users" “\MyUser” “MyPassword” “BtsServer1” “BtsServer1” “BtsServer1” If you have a multi server installation, your script command might look like this: cscript InstallHosts.vbs "MyDomain\BizTalk Application Users" “MyDomain\MyUser” “MyPassword” “BtsServer1” “BtsServer2” “BtsServer2” Running this script will create: Three hosts (BBW_RxHost, BBW_TxHost and BBW_PxHost) Three host instances One send and one receive adapter handler for the WCF NetTcp adapter. You will then need to import the BizTalk MSI via the BizTalk Administration Console.  Open the BizTalk Administration Console, point to the “Applications” node and import the BizTalk Benchmark Wizard.msi found in the same folder as the script above. This will create a “BizTalk Benchmark Wizard” application along with all ports and orchestrations needed. To finish the installation you will need to run the BizTalk Benchmark Wizard.msi on all BizTalk servers to add the assemblies to the Global Assembly Cache (GAC). Next I will look at running the BizTalk Benchmark Wizard.

    Read the article

  • Add a Hovering Image Toolbar to Firefox

    - by Asian Angel
    When you work with webpage images in Firefox you normally have to use the Context Menu to do anything with them. The Image Toolbar extension provides an extra toolbar to use when you hover your mouse over webpage images. Note: This extension will not function if you have the NoScript extension installed/enabled unless JavaScript has permission to be active on that page. Before You can see the available “Context Menu” options for working with images here. Not bad but it would be nice if some other convenient options were available as well. Image Toolbar in Action Once you have installed the extension you will be able to view the toolbar whenever you hover your mouse over an image. All of the commands are active by default but you can choose what is available in the options. The toolbar will also appear in the upper left region of the image but can be set to appear relative to the cursor. Note: The default minimum image size for the toolbar to appear over is “260 x 260 pixels” so you will probably want to change it to a much smaller size (see options below). Here is what is available in the Image Toolbar: Save – Choose between being prompted when saving or automatically saving to a specified location Copy – Copies image and image URL so that you can paste the image or URL depending on the app pasted into Print – Provides print preview and printing capabilities Info – Opens a window with “properties information” about the image Folder – Opens browser’s download folder in Windows Explorer The “Save, Copy, Print, & Folder Commands” are all pretty clear in what you can expect from them but what about the “Info Command”? This is what you will see if you use the “Info Command” and expand the window out all the way. Very nice… Options There are quite a few options available for what appears to be such a small toolbar. The first “Tab Area” lets you set up the “Save Scheme” that best suits your personal needs. You can choose which commands are available in the toolbar, decide if you would like text labels visible, and enable small icons if desired. As mentioned above the default image size for the toolbar to appear is “260 x 260 pixels”…we set ours for “10 x 10 pixels”. If you would like the toolbar to appear relative to your mouse cursor as opposed to the upper left corner of the image then you can select for that here. Conclusion If you have been wanting more options for working with webpage images in Firefox then this will make a very useful and convenient addition to your browser. Links Download the Image Toolbar extension (Mozilla Add-ons) Similar Articles Productive Geek Tips Conserve Space in Firefox by Combining ToolbarsShow Alexa Ranking in FirefoxLightweight Extension to Show PageRank in FirefoxSwitch Windows by Hovering the Mouse Over a Window in Windows 7 or VistaQuick Tip: Show PageRank in Firefox while Google Toolbar is Hidden TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Roadkill’s Scan Port scans for open ports Out of 100 Tweeters Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy

    Read the article

  • SOA Suite 11g Asynchronous Testing with soapUI

    - by Greg Mally
    Overview The Enterprise Manager test harness that comes bundled with SOA Suite 11g is a great tool for doing smoke tests and some minor load testing. When a more robust testing tool is needed, often times soapUI is leveraged for many reasons ranging from ease of use to cost effective. However, when you want to start doing some more complex testing other than synchronous web services with static content, then the free version of soapUI becomes a bit more challenging. In this blog I will show you how to test asynchronous web services with soapUI free edition. The following assumes that you have a working knowledge of soapUI and will not go into concepts like setting up a project etc. For the basics, please review the documentation for soapUI: http://www.soapui.org/Getting-Started/ Asynchronous Web Service Testing in soapUI When invoking an asynchronous web service, the caller must provide a callback for the response. Since our testing will originate from soapUI, then it is only natural that soapUI would provide the callback mechanism. This mechanism in soapUI is called a MockService. In a nutshell, a soapUI MockService is a simulation of a Web Service (aka, a process listening on a port). We will go through the steps in setting up the MockService for a simple asynchronous BPEL process. After creating your soapUI project based on an asynchronous BPEL process, you will see something like the following: Notice that soapUI created an interface for both the request and the response (i.e., callback). The interface that was created for the callback will be used to create the MockService. Right-click on the callback interface and select the Generate MockService menu item: You will be presented with the Generate MockService dialogue where we will tweak the Path and possibly the port (depends upon what ports are available on the machine where soapUI will be running). We will adjust the Path to include the operation name (append /processResponse in this example) and the port of 8088 is fine: Once the MockService is created, you should have something like the following in soapUI: This window acts as a console/view into the callback process. When the play button is pressed (green triangle in the upper left-hand corner), soapUI will start a process running on the configured Port that will accept web service invocations on the configured Path: At this point we are “almost” ready to try out the asynchronous test. But first we must provide the web service addressing (WS-A) configuration on the request message. We will edit the message for the request interface that was generated when the project was created (SimpleAsyncBPELProcessBinding > process > Request 1 in this example). At the bottom of the request message editor you will find the WS-A configuration by left-clicking on the WS-A label: Here we will setup WS-A by changing the default values to: Must understand: TRUE Add default wsa:Action: Add default wsa:Action (checked) Reply to: ${host where soapUI is running}:${MockService Port}${MockService Path} … in this example: http://192.168.1.181:8088/mockSimpleAsyncBPELProcessCallbackBinding/processResponse We now are ready to run the asynchronous test from soapUI free edition. Make sure that the MockService you created is running and then push the play button for the request (green triangle in the upper left-hand corner of the request editor). If everything is configured correctly, you should see the response show up in the MockService window: To view the response message/payload, just double-click on a response message in the Message Log window of the MockService: At this point you can now expand the project to include a Test Suite for some load balance tests etc. This same topic has been covered in various detail on other sites/blogs, but I wanted to simplify and detail how this is done in the context of SOA Suite 11g. It also serves as a nice introduction to another blog of mine: SOA Suite 11g Dynamic Payload Testing with soapUI Free Edition.

    Read the article

  • Ubuntu 10.04 & IBM DS3524 with FC multipath, inactive path is [failed][faulty] instead of [active][ghost]

    - by Graeme Donaldson
    OK, this is my setup: FC Switches IBM/Brocade, Switch1 and Switch2, independent fabrics. Server IBM x3650 M2, 2x QLogic QLE2460, 1 connected to each FC Switch. Storage IBM DS3524, 2x controllers with 4x FC ports each, but only 2x connected on each. +-----------------------------------------------------------------------+ | HBA1 Server HBA2 | +-----------------------------------------------------------------------+ | | | | | | +-----------------------------+ +------------------------------+ | Switch1 | | Switch2 | +-----------------------------+ +------------------------------+ | | | | | | | | | | | | | | | | | | | | +-----------------------------------+-----------------------------------+ | Contr A, port 3 | Contr A, port 4 | Contr B, port 3 | Contr B, port 4 | +-----------------------------------+-----------------------------------+ | Storage | +-----------------------------------------------------------------------+ My /etc/multipath.conf is from the IBM redbook for the DS3500, except I use a different setting for prio_callout, IBM uses /sbin/mpath_prio_tpc, but according to http://changelogs.ubuntu.com/changelogs/pool/main/m/multipath-tools/multipath-tools_0.4.8-7ubuntu2/changelog, this was renamed to /sbin/mpath_prio_rdac, which I'm using. devices { device { #ds3500 vendor "IBM" product "1746 FAStT" hardware_handler "1 rdac" path_checker rdac failback 0 path_grouping_policy multibus prio_callout "/sbin/mpath_prio_rdac /dev/%n" } } multipaths { multipath { wwid xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx alias array07 path_grouping_policy multibus path_checker readsector0 path_selector "round-robin 0" failback "5" rr_weight priorities no_path_retry "5" } } The output of multipath -ll with controller A as the preferred path: root@db06:~# multipath -ll sdg: checker msg is "directio checker reports path is down" sdh: checker msg is "directio checker reports path is down" array07 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) dm-2 IBM ,1746 FASt [size=4.9T][features=1 queue_if_no_path][hwhandler=0] \_ round-robin 0 [prio=2][active] \_ 5:0:1:0 sdd 8:48 [active][ready] \_ 5:0:2:0 sde 8:64 [active][ready] \_ 6:0:1:0 sdg 8:96 [failed][faulty] \_ 6:0:2:0 sdh 8:112 [failed][faulty] If I change the preferred path using IBM DS Storage Manager to Controller B, the output swaps accordingly: root@db06:~# multipath -ll sdd: checker msg is "directio checker reports path is down" sde: checker msg is "directio checker reports path is down" array07 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) dm-2 IBM ,1746 FASt [size=4.9T][features=1 queue_if_no_path][hwhandler=0] \_ round-robin 0 [prio=2][active] \_ 5:0:1:0 sdd 8:48 [failed][faulty] \_ 5:0:2:0 sde 8:64 [failed][faulty] \_ 6:0:1:0 sdg 8:96 [active][ready] \_ 6:0:2:0 sdh 8:112 [active][ready] According to IBM, the inactive path should be "[active][ghost]", not "[failed][faulty]". Despite this, I don't seem to have any I/O issues, but my syslog is being spammed with this every 5 seconds: Jun 1 15:30:09 db06 multipathd: sdg: directio checker reports path is down Jun 1 15:30:09 db06 kernel: [ 2350.282065] sd 6:0:2:0: [sdh] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 1 15:30:09 db06 kernel: [ 2350.282071] sd 6:0:2:0: [sdh] Sense Key : Illegal Request [current] Jun 1 15:30:09 db06 kernel: [ 2350.282076] sd 6:0:2:0: [sdh] <<vendor>> ASC=0x94 ASCQ=0x1ASC=0x94 ASCQ=0x1 Jun 1 15:30:09 db06 kernel: [ 2350.282083] sd 6:0:2:0: [sdh] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 Jun 1 15:30:09 db06 kernel: [ 2350.282092] end_request: I/O error, dev sdh, sector 0 Jun 1 15:30:10 db06 multipathd: sdh: directio checker reports path is down Jun 1 15:30:14 db06 kernel: [ 2355.312270] sd 6:0:1:0: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 1 15:30:14 db06 kernel: [ 2355.312277] sd 6:0:1:0: [sdg] Sense Key : Illegal Request [current] Jun 1 15:30:14 db06 kernel: [ 2355.312282] sd 6:0:1:0: [sdg] <<vendor>> ASC=0x94 ASCQ=0x1ASC=0x94 ASCQ=0x1 Jun 1 15:30:14 db06 kernel: [ 2355.312290] sd 6:0:1:0: [sdg] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 Jun 1 15:30:14 db06 kernel: [ 2355.312299] end_request: I/O error, dev sdg, sector 0 Does anyone know how I can get the inactive path to show "[active][ghost]" instead of "[failed][faulty]"? I assume that once I can get that right then the spam in my syslog will end as well. One final thing worth mentioning is that the IBM redbook doc targets SLES 11 so I'm assuming there's something a little different under Ubuntu that I just haven't figured out yet. Update: As suggested by Mitch, I've tried removing /etc/multipath.conf, and now the output of multipath -ll looks like this: root@db06:~# multipath -ll sdg: checker msg is "directio checker reports path is down" sdh: checker msg is "directio checker reports path is down" xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxdm-1 IBM ,1746 FASt [size=4.9T][features=0][hwhandler=0] \_ round-robin 0 [prio=1][active] \_ 5:0:2:0 sde 8:64 [active][ready] \_ round-robin 0 [prio=1][enabled] \_ 5:0:1:0 sdd 8:48 [active][ready] \_ round-robin 0 [prio=0][enabled] \_ 6:0:1:0 sdg 8:96 [failed][faulty] \_ round-robin 0 [prio=0][enabled] \_ 6:0:2:0 sdh 8:112 [failed][faulty] So its more or less the same, with the same message in the syslog every 5 minutes as before, but the grouping has changed.

    Read the article

  • Oracle Enterprise Manager 11g is Here!

    - by chung.wu
    We hope that you enjoyed the launch event. If you missed it, you may still watch it via our on demand webcast, which is being produced and will be posted very shortly. 11gR1 is a major release of Oracle Enterprise Manager, and as one would expect from a big release, there are many new capabilities that appeal to a broad set of audience. Before going into the laundry list of new features, let's talk about the key themes for this release to put things in perspective. First, this release is about Business Driven Application Management. The traditional paradigm of component centric systems management simply cannot satisfy the management needs of modern distributed applications, as they do not provide adequate visibility of whether these applications are truly meeting the service level expectations of the business users. Business Driven Application Management helps IT manage applications according to the needs of the business users so that valuable IT resources can be better focused to help deliver better business results. To support Business Driven Application Management, 11gR1 builds on the work that we started in 10g to provide better support for user experience management. This capability helps IT better understand how users use applications and the experience that the applications provide so that IT can take actions to help end users get their work done more effectively. In addition, this release also delivers improved business transaction management capabilities to make it faster and easier to understand and troubleshoot transaction problems that impact end user experience. Second, this release includes strengthened Integrated Application-to-Disk Management. Every component of an application environment, from the application logic to the application server, to database, host machines and storage devices, etc... can affect end user experience. After user experience improvement needs are identified, IT needs tools that can be used do deep dive diagnostics for each of the application environment component, analyze configurations and deploy changes. Enterprise Manager 11gR1 extends coverage of key application environment components to include full support for Oracle Database 11gR2, Exadata V2, and Fusion Middleware 11g. For composite and Java application management, two key pieces of technologies, JVM Diagnostic and Composite Application Monitoring and Modeler, are now fully integrated into Enterprise Manager so there is no need to install and maintain separate tools. In addition, we have delivered the first set of integration between Enterprise Manager Grid Control and Enterprise Manager Ops Center so that hardware level events can be centrally monitored via Grid Control. Finally, this release delivers Integrated Systems Management and Support for customers of Oracle technologies. Traditionally, systems management tools and tech support were separate silos. When problems occur, administrators used internally deployed tools to try to solve the problems themselves. If they couldn't fix the problems, then they would use some sort of support website to get help from the vendor's support staff. Oracle Enterprise Manager 11g integrates problem diagnostic and remediation workflow. Administrators can use Oracle Enterprise Manager's various diagnostic tools to begin the troubleshooting process. They can also use the integrated access to My Oracle Support to look up solutions and download software patches. If further help is needed, administrators can open service requests from right within Oracle Enterprise Manager and track status update. Oracle's support staff, using Enterprise Manager's configuration management capabilities, can collect important configuration information about customer environments in order to expedite problem resolution. This tight integration between Oracle Enterprise Manager and My Oracle Support helps Oracle customers achieve a Superior Ownership Experience for their Oracle products. So there you have it. This is a brief 50,000 feet overview of Oracle Enterprise Manager 11g. We know you are hungry for the details. We are going to write about it in the coming days and weeks. For those of you that absolutely can't wait to find out more, you may download our software to try it out today. In fact, for the first time ever, the initial release of Oracle Enterprise Manager is available for both 32 and 64 bit Linux. Additional O/S ports will arrive in the coming weeks. Please stay tuned on the Oracle Enterprise Manager blog for additional updates.

    Read the article

  • Juju stuck in "pending" state when using LXC

    - by Andre
    So I'm trying to get started with Juju, and tried to do this locally using LXC. I followed the instructions here: How do I configure juju for local usage? Unfortunately this doesn't seem to work for me. status shows the following: $ juju status machines: 0: agent-state: running dns-name: localhost instance-id: local instance-state: running services: mysql: charm: cs:precise/mysql-1 relations: db: - wordpress units: mysql/0: agent-state: pending machine: 0 public-address: null wordpress: charm: cs:precise/wordpress-0 exposed: true relations: db: - mysql units: wordpress/0: agent-state: pending machine: 0 open-ports: [] public-address: null 2012-05-10 14:09:38,155 INFO 'status' command finished successfully As you can see the agent-state is 'pending' and there is no public address where I'm able to access the newly created site. Am I missing something here? UPDATE: Tried destroying the environment an doing everything again (multiple times). This is the output for debug-log: ~$ juju debug-log 2012-05-11 08:50:23,790 INFO Enabling distributed debug log. 2012-05-11 08:50:23,806 INFO Tailing logs - Ctrl-C to stop. 2012-05-11 08:50:42,338 Machine:0: juju.agents.machine DEBUG: Units changed old:set([]) new:set(['mysql/0']) 2012-05-11 08:50:42,339 Machine:0: juju.agents.machine DEBUG: Starting service unit: mysql/0 ... 2012-05-11 08:50:42,459 Machine:0: unit.deploy DEBUG: Downloading charm cs:precise/mysql-1 to /home/andre/.juju/data/andre-local/charms 2012-05-11 08:50:42,620 Machine:0: unit.deploy DEBUG: Using <juju.machine.unit.UnitContainerDeployment object at 0x9c54b6c> for mysql/0 in /home/andre/.juju/data/andre-local 2012-05-11 08:50:42,648 Machine:0: unit.deploy DEBUG: Starting service unit mysql/0... 2012-05-11 08:50:42,649 Machine:0: unit.deploy DEBUG: Creating master container... 2012-05-11 08:54:33,992 Machine:0: unit.deploy DEBUG: Created master container andre-local-0-template 2012-05-11 08:54:33,993 Machine:0: unit.deploy INFO: Creating container mysql-0... 2012-05-11 08:56:18,760 Machine:0: unit.deploy INFO: Container created for mysql/0 2012-05-11 08:56:19,466 Machine:0: unit.deploy DEBUG: Charm extracted into container 2012-05-11 08:56:19,569 Machine:0: unit.deploy DEBUG: Starting container... 2012-05-11 08:56:22,707 Machine:0: unit.deploy INFO: Started container for mysql/0 2012-05-11 08:56:22,707 Machine:0: unit.deploy INFO: Started service unit mysql/0 2012-05-11 08:56:23,012 Machine:0: juju.agents.machine DEBUG: Units changed old:set(['mysql/0']) new:set(['wordpress/0', 'mysql/0']) 2012-05-11 08:56:23,039 Machine:0: juju.agents.machine DEBUG: Starting service unit: wordpress/0 ... 2012-05-11 08:56:23,154 Machine:0: unit.deploy DEBUG: Downloading charm cs:precise/wordpress-0 to /home/andre/.juju/data/andre-local/charms 2012-05-11 08:56:23,396 Machine:0: unit.deploy DEBUG: Using <juju.machine.unit.UnitContainerDeployment object at 0x9c519cc> for wordpress/0 in /home/andre/.juju/data/andre-local 2012-05-11 08:56:23,620 Machine:0: unit.deploy DEBUG: Starting service unit wordpress/0... 2012-05-11 08:56:23,621 Machine:0: unit.deploy INFO: Creating container wordpress-0... 2012-05-11 08:58:24,739 Machine:0: unit.deploy INFO: Container created for wordpress/0 2012-05-11 08:58:25,163 Machine:0: unit.deploy DEBUG: Charm extracted into container 2012-05-11 08:58:25,397 Machine:0: unit.deploy DEBUG: Starting container... 2012-05-11 08:58:27,982 Machine:0: unit.deploy INFO: Started container for wordpress/0 2012-05-11 08:58:27,983 Machine:0: unit.deploy INFO: Started service unit wordpress/0 This is the result for the status command (with verbose flag): ~$ juju -v status 2012-05-11 08:51:53,464 DEBUG Initializing juju status runtime 2012-05-11 08:51:53,625:4030(0xb7345b00):ZOO_INFO@log_env@658: Client environment:zookeeper.version=zookeeper C client 3.3.5 2012-05-11 08:51:53,625:4030(0xb7345b00):ZOO_INFO@log_env@662: Client environment:host.name=andre-ufo 2012-05-11 08:51:53,625:4030(0xb7345b00):ZOO_INFO@log_env@669: Client environment:os.name=Linux 2012-05-11 08:51:53,625:4030(0xb7345b00):ZOO_INFO@log_env@670: Client environment:os.arch=3.2.0-24-generic-pae 2012-05-11 08:51:53,625:4030(0xb7345b00):ZOO_INFO@log_env@671: Client environment:os.version=#37-Ubuntu SMP Wed Apr 25 10:47:59 UTC 2012 2012-05-11 08:51:53,626:4030(0xb7345b00):ZOO_INFO@log_env@679: Client environment:user.name=andre 2012-05-11 08:51:53,626:4030(0xb7345b00):ZOO_INFO@log_env@687: Client environment:user.home=/home/andre 2012-05-11 08:51:53,626:4030(0xb7345b00):ZOO_INFO@log_env@699: Client environment:user.dir=/home/andre 2012-05-11 08:51:53,626:4030(0xb7345b00):ZOO_INFO@zookeeper_init@727: Initiating client connection, host=192.168.122.1:41779 sessionTimeout=10000 watcher=0xb7780620 sessionId=0 sessionPasswd=<null> context=0x9242ee8 flags=0 2012-05-11 08:51:53,627:4030(0xb6b90b40):ZOO_INFO@check_events@1585: initiated connection to server [192.168.122.1:41779] 2012-05-11 08:51:53,649:4030(0xb6b90b40):ZOO_INFO@check_events@1632: session establishment complete on server [192.168.122.1:41779], sessionId=0x1373ae057d90007, negotiated timeout=10000 2012-05-11 08:51:53,651 DEBUG Environment is initialized. machines: 0: agent-state: running dns-name: localhost instance-id: local instance-state: running services: mysql: charm: cs:precise/mysql-1 relations: db: - wordpress units: mysql/0: agent-state: pending machine: 0 public-address: null wordpress: charm: cs:precise/wordpress-0 relations: db: - mysql units: wordpress/0: agent-state: pending machine: 0 public-address: null

    Read the article

  • Beginner Geek: How to Burn an ISO Image to a Disc

    - by Mysticgeek
    There may be a time when you have an ISO image that you need to burn to a CD or DVD for use in a computer or other device. Today we show you how to do it using ImgBurn, ISO Recorder, and Windows Disc Image Burner in Windows 7. You might need to burn an ISO of an operating system, software app, CD, DVD…etc. It doesn’t matter what the ISO image is, burning an image is a fairly straight-forward process and here we’ll take a look at three free options to accomplish it. Using ImgBurn ImgBurn is an awesome free utility that will create ISO images, allow out burn almost anything, and a lot more. Although there are a lot advanced features available, burning an ISO to disc is easy. Download and install ImgBurn (link below) taking the defaults in the install wizard. The main thing to watch for and uncheck during installation is when it offers the worthless Ask Toolbar. The easiest way to use ImgBurn is to burn an image to disc is pop in a blank disc to the CD/DVD drive, right-click on the ISO file, and select Burn using ImgBurn. ImgBurn opens up with the source and destination fields already filled in. You can leave the default settings, then click the Write button. You’ll notice that the ImgBurn Log screen opens, this is by default and is meant to show error messages you may receive during the writing process.   A successful burn! That is all there is to it…click Ok and close out of ImgBurn. Use ISO Recorder ISO Recorder (link below) is another great utility for burning ISO images to disc. They have a version for XP, Vista, and Windows 7 (32 & 64-bit Versions). Pop your blank disc into your CD/DVD drive and right-click on the ISO image file and select Copy image to CD from the Context Menu. In the next screen the image file path is in the Source Image file field. Under Recorder select the drive with your blank disc, select a recording speed and click Next. You’ll see a progress screen while the data is written to the disc and finalizing… That’s it! Your disc will pop out and you can click Finish to close out of ISO Recorder. Use Windows 7 If You’re using Windows 7, use the built in Windows Disc Image Burner feature to burn ISO images to disc. The process is very straight-forward, and for a full walkthrough on this, check out our article on how to burn an ISO image in Windows 7. Conclusion You don’t need an expensive commercial application to burn an ISO image to disc. Using any one of these free utilities will get the job done quite nicely. Download ImgBurn Download ISO Recorder Similar Articles Productive Geek Tips How to Make a Windows Vista Repair Disk If You Don’t Have OneHow to Create a Windows ISO from a Disc Using ImgBurnEasily Burn Discs With BurnAware Free EditionCreate A Windows Home Server Home Computer Restore DiscWhy is Amarok’s "Burn This Album" Disabled in Ubuntu? TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Google Translate (for animals) Out of 100 Tweeters Roadkill’s Scan Port scans for open ports Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows If it were only this easy

    Read the article

  • Using the Onboard VGA output with a PCIe video card. Both nVidia

    - by sebikul
    I have 2 video cards, one On board, a nVidia 6150SE nForce 430 and a PCIe nVidia GeForce GT 220 1GB DDR2 RAM I have already configured the PCIe card to use the dual monitor feature, using the VGA and HDMI ports, but now I want to add a third monitor, using the On board VGA port I have managed to enable the On board graphics processor, which is taking 400MB of ram, but I cant manage to use it, nvidia-settings does not detect it, like it's not usable (but is there) My questions are the following: How can I manage to get the On board VGA display to work together with the PCIe graphics card? If possible, how can I recover those 400 MB the on board card is taking (even without being used) or how can I get it to use the PCIe card available memory? System Details: Linux 2.6.35-28-generic i686 Ubuntu 10.10 (All updates installed) NVIDIA Driver Version: 260.19.06 (Official) If more info is needed please let me know. Here is the lspci output when the On board card is disabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) And this is when both are enabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) Output of lshw -class display: *-display description: VGA compatible controller product: GT216 [GeForce GT 220] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:02:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:df000000-dfffffff memory:c0000000-cfffffff memory:da000000-dbffffff ioport:ef80(size=128) memory:def80000-deffffff *-display description: VGA compatible controller product: C61 [GeForce 6150SE nForce 430] vendor: nVidia Corporation physical id: d bus info: pci@0000:00:0d.0 version: a2 width: 64 bits clock: 66MHz capabilities: pm msi vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:22 memory:dd000000-ddffffff memory:b0000000-bfffffff memory:dc000000-dcffffff memory:deb40000-deb5ffff If what I'm looking for is not possible, please tell me, so I can disable the On board card and recover those 400MB of wasted RAM Thanks for your help!

    Read the article

  • RPi and Java Embedded GPIO: Writing Java code to blink LED

    - by hinkmond
    So, you've followed the previous steps to install Java Embedded on your Raspberry Pi ?, you went to Fry's and picked up some jumper wires, LEDs, and resistors ?, you hooked up the wires, LED, and resistor the the correct pins ?, and now you want to start programming in Java on your RPi? Yes? ???????! OK, then... Here we go. You can use the following source code to blink your first LED on your RPi using Java. In the code you can see that I'm not using any complicated gpio libraries like wiringpi or pi4j, and I'm not doing any low-level pin manipulation like you can in C. And, I'm not using python (hell no!). This is Java programming, so we keep it simple (and more readable) than those other programming languages. See: Write Java code to do this In the Java code, I'm opening up the RPi Debian Wheezy well-defined file handles to control the GPIO ports. First I'm resetting everything using the unexport/export file handles. (On the RPi, if you open the well-defined file handles and write certain ASCII text to them, you can drive your GPIO to perform certain operations. See this GPIO reference). Next, I write a "1" then "0" to the value file handle of the GPIO0 port (see the previous pinout diagram). That makes the LED blink. Then, I loop to infinity. Easy, huh? import java.io.* /* * Java Embedded Raspberry Pi GPIO app */ package jerpigpio; import java.io.FileWriter; /** * * @author hinkmond */ public class JerpiGPIO { static final String GPIO_OUT = "out"; static final String GPIO_ON = "1"; static final String GPIO_OFF = "0"; static final String GPIO_CH00="0"; /** * @param args the command line arguments */ public static void main(String[] args) { FileWriter commandFile; try { /*** Init GPIO port for output ***/ // Open file handles to GPIO port unexport and export controls FileWriter unexportFile = new FileWriter("/sys/class/gpio/unexport"); FileWriter exportFile = new FileWriter("/sys/class/gpio/export"); // Reset the port unexportFile.write(GPIO_CH00); unexportFile.flush(); // Set the port for use exportFile.write(GPIO_CH00); exportFile.flush(); // Open file handle to port input/output control FileWriter directionFile = new FileWriter("/sys/class/gpio/gpio"+GPIO_CH00+"/direction"); // Set port for output directionFile.write(GPIO_OUT); directionFile.flush(); /*--- Send commands to GPIO port ---*/ // Opne file handle to issue commands to GPIO port commandFile = new FileWriter("/sys/class/gpio/gpio"+GPIO_CH00+"/value"); // Loop forever while (true) { // Set GPIO port ON commandFile.write(GPIO_ON); commandFile.flush(); // Wait for a while java.lang.Thread.sleep(200); // Set GPIO port OFF commandFile.write(GPIO_OFF); commandFile.flush(); // Wait for a while java.lang.Thread.sleep(200); } } catch (Exception exception) { exception.printStackTrace(); } } } Hinkmond

    Read the article

  • Using 3G/UMTS in Mauritius

    After some conversation, threads in online forum and mailing lists I thought about writing this article on how to setup, configure and use 3G/UMTS connections on Linux here in Mauritius. Personally, I can only share my experience with Emtel Ltd. but try to give some clues about how to configure Orange as well. Emtel 3G/UMTS surf stick Emtel provides different surf sticks from Huawei. Back in 2007, I started with an E220 that wouldn't run on Windows Vista either. Nowadays, you just plug in the surf stick (ie. E169) and usually the Network Manager will detect the new broadband modem. Nothing to worry about. The Linux Network Manager even provides a connection profile for Emtel here in Mauritius and establishing the Internet connection is done in less than 2 minutes... even quicker. Using wvdial Old-fashioned Linux users might not take Network Manager into consideration but feel comfortable with wvdial. Although that wvdial is primarily used with serial port attached modems, it can operate on USB ports as well. Following is my configuration from /etc/wvdial.conf: [Dialer Defaults]Phone = *99#Username = emtelPassword = emtelNew PPPD = yesStupid Mode = 1Dial Command = ATDT[Dialer emtel]Modem = /dev/ttyUSB0Baud = 3774000Init2 = ATZInit3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Init4 = AT+cgdcont=1,"ip","web"ISDN = 0Modem Type = Analog Modem The values of user name and password are optional and can be configured as you like. In case that your SIM card is protected by a pin - which is highly advised, you might another dialer section in your configuration file like so: [Dialer pin]Modem = /dev/ttyUSB0Init1 = AT+CPIN=0000 This way you can "daisy-chain" your command to establish your Internet connection like so: wvdial pin emtel And it works auto-magically. Depending on your group assignments (dialout), you might have to sudo the wvdial statement like so: sudo wvdial pin emtel Orange parameters As far as I could figure out without really testing it myself, it is also necessary to set the Access Point (AP) manually with Orange. Well, although it is pretty obvious a lot of people seem to struggle. The AP value is "orange". [Dialer orange]Modem = /dev/ttyUSB0Baud = 3774000Init2 = ATZInit3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0Init4 = AT+cgdcont=1,"ip","orange"ISDN = 0Modem Type = Analog Modem And you are done. Official Linux support from providers It's just simple: Forget it! The people at the Emtel call center are completely focused on the hardware and Mobile Connect software application provided by Huawei and are totally lost in case that you confront them with other constellations. For example, my wife's netbook has an integrated 3G/UMTS modem from Ericsson. Therefore, no need to use the Huawei surf stick at all and of course we use the existing software named Wireless Manager instead of. Now, imagine to mention at the help desk: "Ehm, sorry but what's Mobile Connect?" And Linux after all might give the call operator sleepless nights... Who knows? Anyways, I hope that my article and configuration could give you a helping hand and that you will be able to connect your Linux box with 3G/UMTS surf sticks here in Mauritius.

    Read the article

  • How to set default xrandr settings?

    - by echo-flow
    I'm trying to enable dual monitors in Ubuntu. This is working fine, but every time I do it, desktop effects is disabled. I think I've found the reason why, though: https://wiki.ubuntu.com/X/Config/Multihead/ As with the GNOME XRandR configuration method, setting Virtual to too large a value may result in a loss of hardware acceleration, and thus an inability to use Compiz and its desktop effects. When I use the GNOME monitor applet, or the Monitors configuration in the System menu, the default xrandr settings puts the second monitor to the right of the first, and, as I found with this bug, for most monitors this creates a virtual desktop larger than the maximum 2048 horizontal resolution needed for hardware acceleration on my netbook hardware. So, it seems like if I can modify xrandr's default settings so that it places the new desktop above or below (north or south of) the main LVDS display, then hardware acceleration, and therefore compiz will continue to work. Can anyone tell me, what is the easiest way to achieve this? UPDATE: I have confirmed that multihead support with desktop effects and hardware acceleration works when I move the external monitor display north of the main LVDS display. Right now this involves the following process: plugging in the external monitor, starting the Monitors configuration menu, desktop effects are disabled automatically (and all of the windows on my workspaces are moved to the first workspace), repositioning the external display so that it is north of LVDS display and clicking apply, and then navigating to the Appearance menu and telling it to reenable desktop effects. Is there a simpler way do this? UPDATE 2: OK, so I thought that perhaps the GNOME Monitors configuration screen was trying to be clever, and might be disbling desktop effects. So, I just tried using the xrandr command-line client instead, as follows: xrandr --output VGA1 --above LVDS1 When I do that, desktop effects are still disabled, and I need to manually reenable them. This, despite the fact that hardware acceleration works, and there is never a point where hardware acceleration stops working because the horizontal dimension of the virtual display is too large. So what program is trying to be clever, and is turning off desktop effects when it doesn't need to? And how do I make it stop? If there were a way to re-enable desktop effects from the command line, which I could then put into a script along with the proper xrandr invocation, I would accept that as a workaround. UPDATE 3: OK, here's my script to enable a second monitor with desktop effects. It might be evil, I'm not sure: second-monitor.sh xrandr --output VGA1 --above LVDS1 sleep 3 compiz --replace & The sleep statement might not be necessary. If there's a better way to do this, please let me know. UPDATE 4: This is a Dell Mini Inspiron 1012. Here are my system specifications: lspci -vv 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 29 Region 0: Memory at f0b00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at 18d0 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at f0900000 (32-bit, non-prefetchable) [size=1M] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: Dell Device 041a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0b80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> lsmod | grep i915 i915 287458 2 drm_kms_helper 29329 1 i915 drm 162409 3 i915,drm_kms_helper intel_agp 24375 2 i915 i2c_algo_bit 5028 1 i915 video 17375 1 i915

    Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >