Search Results

Search found 4906 results on 197 pages for 'ssh tunnel'.

Page 98/197 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• VPN using Zywall

  - by Rune FS

  I've played around with a certificate based VPN (normally I don't do hardware) we've manged to setup the connection and the tunnel between the routers is working correctly. We now need the last step. There's no connection to the computers on the other end. What could we have forgotten? (we're testing with two standard configured Win7 machines) EDIT: Just to clarify the tunnel is working I can ping the router on the other end. I can't access the computers on the other side of that router and vice versa. (It's also possible to access the remotemangement console of the remote router on the LAN IP)

  Read the article

• Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

  - by Lock

  I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Allow VMWare client to connect only via VPN

  - by Frank Meulenaar

  I have a VMWare (currently using Workstation on Vista, but thinking about switching to ESX) client with Windows XP. I've installed OpenVPN in the client and it connects to the corporate VPN server. I want to make sure that all traffic from the Windows XP machine goes trough this VPN tunnel, but I can't change any settings on the corporate VPN server. Is it possible to restrict the internet connectivity of the Windows XP client in such a way that it can only send packets to the IP of the corporate VPN server? In that way it'd be impossible for packets to bypass the tunnel. I've looked at NAT configurations but couldn't see how I could make this setup.

  Read the article

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• EC2 server in VPC stops responding joining domain

  - by Geoff

  We have a EC2 Windows Server set up and running in our VPC, connected to our network via a Juniper 5GT. This is working well, with the tunnel up and stable. If I then join the server to our local domain, it appears to work - I can then log on using domain credentials, and use domain accounts when applying security to folders etc. After I log out, if I give it around an hour, the box becomes unresponsive. I can't ping it, although a tracert goes all the way barring the last hop - so the tunnel is ok. I can't RDP into it. If I reboot it, then it works for a while before doing the same thing. Un-joining it from the domain fixes the problem, and it stays up and stable. The event logs don't show anything obvious, at least to me. Any ideas?

  Read the article

• vagrant fails to bring up additional adapter for centos vm using virtual box provider

  - by Anadi Misra

  this is in continuation of the question asked here about host only adapter on dhcp I upgraded to vagrant 1.6.3 and the updated Vagrantfile to following setting for multiple adapters # add additional adapter for inter machine networking dev.vm.network :private_network, :type => "dhcp", :adapter => "2", :netmask => "255.255.255.0" it goes through creating adapters but then fails bringing up the mic on vm Anadis-MacBook-Pro:full-stack-env anadi$ vagrant up Bringing machine 'full-stack-env' up with 'virtualbox' provider... ==> full-stack-env: Clearing any previously set forwarded ports... ==> full-stack-env: Clearing any previously set network interfaces... ==> full-stack-env: Preparing network interfaces based on configuration... full-stack-env: Adapter 1: nat full-stack-env: Adapter 2: hostonly ==> full-stack-env: Forwarding ports... full-stack-env: 22 => 4223 (adapter 1) full-stack-env: 8080 => 8090 (adapter 1) ==> full-stack-env: Running 'pre-boot' VM customizations... ==> full-stack-env: Booting VM... ==> full-stack-env: Waiting for machine to boot. This may take a few minutes... full-stack-env: SSH address: 127.0.0.1:4223 full-stack-env: SSH username: vagrant full-stack-env: SSH auth method: private key full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Remote connection disconnect. Retrying... ==> full-stack-env: Machine booted and ready! ==> full-stack-env: Checking for guest additions in VM... ==> full-stack-env: Setting hostname... ==> full-stack-env: Configuring and enabling network interfaces... The following SSH command responded with a non-zero exit status. Vagrant assumes that this means the command failed! ARPCHECK=no /sbin/ifup eth 2> /dev/null Stdout from the command: Device eth does not seem to be present, delaying initialization. Stderr from the command: how ever when I log in to the environment I see two network interfaces as expected Anadis-MacBook-Pro:full-stack-env anadi$ vagrant ssh Last login: Wed Jun 4 12:54:47 2014 from 10.0.2.2 [vagrant@full-stack-env ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:BD:39:57 inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:febd:3957/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:511 errors:0 dropped:0 overruns:0 frame:0 TX packets:360 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54574 (53.2 KiB) TX bytes:46675 (45.5 KiB) eth1 Link encap:Ethernet HWaddr 08:00:27:A3:86:C9 inet addr:172.28.128.3 Bcast:172.28.128.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:86c9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1360 (1.3 KiB) TX bytes:894 (894.0 b) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) I am bit confused here on why it is trying to add another mic (eth2)? In the VM I used for creating this vagrant box, I had added two NICs already.

  Read the article

• EC2 server in VPC stops responding after joining domain

  - by Geoff

  We have a EC2 Windows Server set up and running in our VPC, connected to our network via a Juniper 5GT. This is working well, with the tunnel up and stable. If I then join the server to our local domain, it appears to work - I can then log on using domain credentials, and use domain accounts when applying security to folders etc. After I log out, if I give it around an hour, the box becomes unresponsive. I can't ping it, although a tracert goes all the way barring the last hop - so the tunnel is ok. I can't RDP into it. If I reboot it, then it works for a while before doing the same thing. Un-joining it from the domain fixes the problem, and it stays up and stable. The event logs don't show anything obvious, at least to me. Any ideas?

  Read the article

• Security Access Control With Solaris Virtualization

  - by Thierry Manfe-Oracle

  Numerous Solaris customers consolidate multiple applications or servers on a single platform. The resulting configuration consists of many environments hosted on a single infrastructure and security constraints sometimes exist between these environments. Recently, a customer consolidated many virtual machines belonging to both their Intranet and Extranet on a pair of SPARC Solaris servers interconnected through Infiniband. Virtual Machines were mapped to Solaris Zones and one security constraint was to prevent SSH connections between the Intranet and the Extranet. This case study gives us the opportunity to understand how the Oracle Solaris Network Virtualization Technology —a.k.a. Project Crossbow— can be used to control outbound traffic from Solaris Zones. Solaris Zones from both the Intranet and Extranet use an Infiniband network to access a ZFS Storage Appliance that exports NFS shares. Solaris global zones on both SPARC servers mount iSCSI LU exported by the Storage Appliance.  Non-global zones are installed on these iSCSI LU. With no security hardening, if an Extranet zone gets compromised, the attacker could try to use the Storage Appliance as a gateway to the Intranet zones, or even worse, to the global zones as all the zones are reachable from this node. One solution consists in using Solaris Network Virtualization Technology to stop outbound SSH traffic from the Solaris Zones. The virtualized network stack provides per-network link flows. A flow classifies network traffic on a specific link. As an example, on the network link used by a Solaris Zone to connect to the Infiniband, a flow can be created for TCP traffic on port 22, thereby a flow for the ssh traffic. A bandwidth can be specified for that flow and, if set to zero, the traffic is blocked. Last but not least, flows are created from the global zone, which means that even with root privileges in a Solaris zone an attacker cannot disable or delete a flow. With the flow approach, the outbound traffic of a Solaris zone is controlled from outside the zone. Schema 1 describes the new network setting once the security has been put in place. Here are the instructions to create a Crossbow flow as used in Schema 1 : (GZ)# zoneadm -z zonename halt ...halts the Solaris Zone. (GZ)# flowadm add-flow -l iblink -a transport=TCP,remote_port=22 -p maxbw=0 sshFilter  ...creates a flow on the IB partition "iblink" used by the zone to connect to the Infiniband.  This IB partition can be identified by intersecting the output of the commands 'zonecfg -z zonename info net' and 'dladm show-part'.  The flow is created on port 22, for the TCP traffic with a zero maximum bandwidth.  The name given to the flow is "sshFilter". (GZ)# zoneadm -z zonename boot  ...restarts the Solaris zone now that the flow is in place.Solaris Zones and Solaris Network Virtualization enable SSH access control on Infiniband (and on Ethernet) without the extra cost of a firewall. With this approach, no change is required on the Infiniband switch. All the security enforcements are put in place at the Solaris level, minimizing the impact on the overall infrastructure. The Crossbow flows come in addition to many other security controls available with Oracle Solaris such as IPFilter and Role Based Access Control, and that can be used to tackle security challenges.

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• got VPN l2l connect between a site & HQ but not traffice using ASA5505 on both ends

  - by vinlata

  Hi, Could anyone see what did I do wrong here? this is one configuration of site1 to HQ on ASA5505, I can get connected but seems like no traffic going (allowed) between them, could it be a NAT issue? any helps would much be appreciated Thanks interface Vlan1 nameif inside security-level 100 ip address 172.30.205.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address pppoe setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! passwd .dIuXDIYzD6RSHz7 encrypted ftp mode passive dns server-group DefaultDNS domain-name errg.net object-group network HQ network-object 172.22.0.0 255.255.0.0 network-object 172.22.0.0 255.255.128.0 network-object 172.22.0.0 255.255.255.128 network-object 172.22.1.0 255.255.255.128 network-object 172.22.1.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_20_cryptomap extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list inside_nat0_outbound extended permit ip 172.30.205.0 255.255.255.0 o bject-group HQ access-list policy-nat extended permit ip 172.30.205.0 255.255.255.0 172.22.0.0 255.255.0.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) 172.30.205.0 access-list policy-nat access-group inside_access_in in interface inside access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute username errgadmin password Os98gTdF8BZ0X2Px encrypted privilege 15 http server enable http 64.42.2.224 255.255.255.240 outside http 172.22.0.0 255.255.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 190 match address outside_20_cryptomap crypto map outside_map 190 set pfs crypto map outside_map 190 set peer 66.7.249.109 crypto map outside_map 190 set transform-set ESP-3DES-SHA crypto map outside_map 190 set phase1-mode aggressive crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp nat-traversal 190 crypto isakmp ipsec-over-tcp port 10000 tunnel-group 66.7.249.109 type ipsec-l2l tunnel-group 66.7.249.109 ipsec-attributes pre-shared-key * telnet timeout 5 ssh 172.30.205.0 255.255.255.0 inside ssh 172.22.0.0 255.255.0.0 outside ssh 64.42.2.224 255.255.255.240 outside ssh 172.25.0.0 255.255.128.0 outside ssh timeout 5 console timeout 0 management-access inside vpdn group PPPoEx request dialout pppoe vpdn group PPPoEx localname [email protected] vpdn group PPPoEx ppp authentication pap vpdn username [email protected] password ********* dhcpd address 172.30.205.100-172.30.205.131 inside dhcpd dns 172.22.0.133 68.94.156.1 interface inside dhcpd wins 172.22.0.133 interface inside dhcpd domain errg.net interface inside dhcpd enable inside ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! end

  Read the article

• Generating random tunnels

  - by IVlad

  What methods could we use to generate a random tunnel, similar to the one in this classic helicopter game? Other than that it should be smooth and allow you to navigate through it, while looking as natural as possible (not too symmetric but not overly distorted either), it should also: Most importantly - be infinite and allow me to control its thickness in time - make it narrower or wider as I see fit, when I see fit; Ideally, it should be possible to efficiently generate it with smooth curves, not rectangles as in the above game; I should be able to know in advance what its bounds are, so I can detect collisions and generate powerups inside the tunnel; Any other properties that let you have more control over it or offer optimization possibilities are welcome. Note: I'm not asking for which is best or what that game uses, which could spark extended discussion and would be subjective, I'm just asking for some methods that others know about or have used before or even think they might work. That is all, I can take it from there. Also asked on stackoverflow, where someone suggested I should ask here too. I think it fits in both places, since it's as much an algorithm question as it is a gamedev question, IMO.

  Read the article

• All email directed to 3rd party vendor except for one specific domain. How?

  - by jherlitz

  So we setup a site to site vpn tunnel with another company. We then proceeded to setup a DNS zone on each others dns servers and entered in each others Mail server name and IP, MX record and WWW record. This allowed us to send emails to each others mail servers through the site to site vpn. Now recently the other company started using MX Logic to scan all outbound and incoming mail. So all outbound email is directed to MX Logic. However we still want email between us to travel across the the Site to Site VPN tunnel. How can we specify that to happen for just one domain not to be directed to MX Logic? Stump on both ends and looking for help.

  Read the article

• VPNs - The ins and outs of IPSec & VPNs in general [on hold]

  - by Magus

  I have to decided to mess around with VPNs on my home router, to access a couple of servers in the back room of my house, however, I went into this thinking happy thoughts and easy-peasy-lemon-squeezy... Now I feel like doing drugs, as if maybe that will help me understand the myriad of terms which come with this nifty little tool. Basically, I do understand WHAT a VPN is, but I have no idea how to set one up. I have a Cisco router ( will supply more info if needed ), and would prefer to use IPSec for this ordeal. I'd like to have the following terms explained ( and yes, I have used the famous Google to help, close but no cigar ) : "Local Secure Group", "Remote Secure Group", "Remote Secure Gateway", how different types of "Keys" work ( again, I know the basics ), and for the "Add VPN Config" screen on the connecting device: "Server, does it have to be an address, or just an IP?", "Account; is this the tunnel name?", I am going to assume 'Password' means the Key, "Group Name; or is THIS the tunnel name?", and "Secret; I halfish know what this is..." I would really appreciate any contribution made, no matter how small, even if it includes a redirect. I just want to learn. Thanks in advance! Magus

  Read the article

• Usage of putty in command line from Hudson

  - by kij

  Hi, I'm trying to use putty in command line from an hudson job. The command is the following one: putty -ssh -2 -P 22 USERNAME@SERVER_ADDR -pw PASS -m command.txt Where 'command.txt' is a shell script to execute in the server through SSH. If i launch this command from the Window command prompt, it works, the shell script is executed on the server machine. If i launch a build of the hudson job configured with this batch command, it doesn't work. The build is running... and running... and running.. without doing anything, and i have to stop it manually. So my question is: Is it possible to launch an external programm (i.e. putty) from an hudson job ? ps: i tried SSH plugin but... not a really good plugin (pre/post build, fail status of the commands launched not caught by hudson, etc.) Thanks in advance for your help. Best regards. kij EDIT: These are the build logs: [workspace] $ cmd /c call C:\WINDOWS\TEMP\hudson7429256014041663539.bat C:\Hudson\jobs\Artifact deployer\workspace>putty -ssh -2 -P 22 USER@SERV_ADD -pw PASS -m com.txt Le build a été annulé Finished: ABORTED And the Hudson.err.log file at the same time (after a stop): 3 juin 2010 18:27:28 hudson.model.Run run INFO: Artifact deployer #6 aborted java.lang.InterruptedException at java.lang.ProcessImpl.waitFor(Native Method) at hudson.Proc$LocalProc.join(Proc.java:179) at hudson.Launcher$ProcStarter.join(Launcher.java:278) at hudson.tasks.CommandInterpreter.perform(CommandInterpreter.java:83) at hudson.tasks.CommandInterpreter.perform(CommandInterpreter.java:58) at hudson.tasks.BuildStepMonitor$1.perform(BuildStepMonitor.java:19) at hudson.model.AbstractBuild$AbstractRunner.perform(AbstractBuild.java:601) at hudson.model.Build$RunnerImpl.build(Build.java:174) at hudson.model.Build$RunnerImpl.doRun(Build.java:138) at hudson.model.AbstractBuild$AbstractRunner.run(AbstractBuild.java:416) at hudson.model.Run.run(Run.java:1241) at hudson.model.FreeStyleBuild.run(FreeStyleBuild.java:46) at hudson.model.ResourceController.execute(ResourceController.java:88) at hudson.model.Executor.run(Executor.java:124) My shell script only write "hello" in a "hello.txt" file on the server, and nothing is done.

  Read the article

• Pushing to bare Git repository (remote) causes it to stop being bare

  - by NSD

  I have a local repository called TestRepo. I clone it with the --bare option, zip this clone up, and throw it on my server. Unzip it, and it's still bare. I then clone the bare remote repository locally over ssh with something like git clone ssh://[email protected]/~/TestRepo.git TestRepoCloned The local TestRepoCloned is not bare and has a remote called "origin." It appears to be tracking correctly from the looks of its config file [core] repositoryformatversion = 0 filemode = true bare = false logallrefupdates = true ignorecase = true [remote "origin"] fetch = +refs/heads/*:refs/remotes/origin/* url = ssh://[email protected]/~/TestRepo.git [branch "master"] remote = origin merge = refs/heads/master I edit an existing file. I commit the change to the current branch (master) via git commit -a -m "Edited a file." The commit succeeds and all is well. I decide to push this change to the remote repository via SSH with a git push The remote repository is now no longer bare, but has a complete working directory, and I get continuous error messages on all further attempts to push to it. Everything I've read seems to suggest that what I'm doing is correct, but it simply is not working. How am I supposed to push changes to a bare remote repo and actually keep it bare?

  Read the article

• SVN authz, path-based authentication woes

  - by Ronny

  [groups] developer = a,b,c doc = r,x [/doc] @doc = rw @developer = rw [/] @developer = rw * = If now a member of the group doc tries to check out the documentation, it does not work. I want members of doc just to be able to check out the sub-dir doc, anything else is forbidden. Any ideas howto achieve this? kind regards ronny [update] client: svn, version 1.5.4 (r33841) server: svn, Version 1.4.6 (r28521) access via svn+ssh:/user@host/fullpath-to-repos 1 perfectly works for two years 2 might be - see version numbers above (I'll contant our admin, immediatelly) 3 no? just ssh 4 nope 5 nope [update] using client version svn 1.4.6 (r28521) does not work either - same errors I use plain command line access. svn co svn+ssh://.... [update] server:Linux 2.6.16.60-0.39.3-default9 i686 athlon i386 GNU/Linux - suse 10? or something like that I think client: Kubuntu 9.04 connection via OpenSSH SSH client the server rejects svn:// connections from localhost - any connection --- gotta try it with a copy at home time soon [update 4] * this is not my own server, I cannot do what I want with it. It is a very old server 10 years at least running, with hundreds of users. Standard things should work. correct me if I am missing something. [update 5] believe it or not. I was using the wrong path and now everything works perfectly well, I am sorry to have wasted your time. I'll give the bounty to FoxyBOA for his efford.

  Read the article

• IPMI queries to multiple nodes at once

  - by lorin

  I'm using IPMI to manage some nodes in a cluster. I'd like to be able to submit IPMI queries to all of the nodes in parallel. Something similar to Cluster SSH or tentakel, except that it wraps ipmitool instead of ssh. Are there any tools like that?

  Read the article

• OpenVPN Clients using server's connection (with no default gateway)

  - by Branden Martin

  I wanted an OpenVPN server so that I could create a private VPN network for staff to connect to the server. However, not as planned, when clients connect to the VPN, it's using the VPN's internet connection (ex: when going to whatsmyip.com, it's that of the server and not the clients home connection). server.conf local <serverip> port 1194 proto udp dev tun ca ca.crt cert x.crt key x.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 9 client.conf client dev tun proto udp remote <srever> 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert x.crt key x.key ns-cert-type server comp-lzo verb 3 Server's route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 69.64.48.0 * 255.255.252.0 U 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 Server's IP Tables Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-proftpd tcp -- anywhere anywhere multiport dports ftp,ftp-data,ftps,ftps-data fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-proftpd (1 references) target prot opt source destination RETURN all -- anywhere anywhere Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- anywhere anywhere My goal is that clients can only talk to the server and other clients that are connected. Hope I made sense. Thanks for the help!

  Read the article

• backup of KVM VM's running on Ubuntu 12.4.1 precise edition from a remote machine

  - by Dr. Death

  I am creating a library API which will take the backup of all the VM's running on KVM hypervisor. My VM's can be of any type. I am taking this backup from a remote machine and need to put the backup at remote server. I have KVM, Libvirt installed on my system. Some of my VM's are LVM based and some are normal VM's running on KVM. I research and found out an excellent perl script for taking the backup http://pof.eslack.org/2010/12/23/best-solution-to-fully-backup-kvm-virtual-machines/ but since I am developing this library in C++ I cannot use it however it has given me a good understanding of how it will work. One thing I didnot able to sort out is if my VM's are not created using virt-manager or are created using any other tool them virsh system list command does not give them in the list of running VM's however they are running perfectly on my KVM server. Is there a way to list these VM's in my system list anyhow? secondly, when I am taking backup from the remote machine I am getting out of my ssh mode as soon as my libvirt command finishes and for every command I need to ssh again, Is there a way that I do not need to ssh each and every time? I have already used the rsa key for ssh but when once my command finishes my control moves to the remote machine again and try to find out my source VM location in remote machine's local drives which in turn fails it. here is the main problem I am facing. also for the LVM based VM I am able to take the live backup but for non LVM based my machines are getting suspended and not been able to take the live backup. Since my library will work on the remote machine only I might not know the VM's configruation on the KVM server. so need to make it consistent for all the VM's. Please share any thing related to this issue so that I may be able to take the live backup of the non lvm vm's also. I'll update my working and any research findings time to time to all of you. Thanks in advance for your suggestions in these regards.

  Read the article

• What is the ip range of EC2

  - by Nicolas Kassis

  I'd like to setup a rule to block ssh request from EC2 since I've been seeing a large amount of ssh base attack from there and was wondering if anyone knew what their IP ranges are.

  Read the article

• My server freezes within a few hours of logging out. Staying logged in keeps the server running

  - by HappyEngineer

  I have an Ubuntu Godaddy server I use to host mail and webapps. It started having problems a couple months ago. It would lock up and stop responding to anything. I couldn't ssh into it, so I'd have godaddy power cycle the server. I have never seen anything that looked suspicious in the var logs (although I'm no expert at reading them). An fsck turned up no problems. Godaddy replaced the ram, but found no hardware problems. I started logging the output from "top" to a log file and found that even that stops running when the server freezes. Now, here is the crazy part: It got so bad that it would actually go down every few hours, but then it stopped going down. I eventually realized I had left an ssh terminal logged into the machine running top. This seemed unlikely to be a reason, but after the server was up with no problems for a full week (remember, it had been going down after just a few hours), I disconnected from the ssh session. Lo and behold, within a few hours the server froze again! I had them power cycle again and then left another ssh session open with top. It has been going without problems for 8 days now. I told others about this and they hardly believe me. I simply can't imagine what is going on. I don't know what else to try other than to just get a new server and reinstall everything. Does anyone have any ideas about what I can look for to determine what the cause is? Is it possible there's some sort of exploit on the server which only runs if everyone is logged out of the system? EDIT: The power management gone haywire sounds plausible, so I've modified the /boot/grub/menu.lst to boot with acpi=off and apm=off. It appears to have prevented kacpid and kacpid_notify from being in the process list, so I assume I did that right. I've disconnected all my sessions from the server. I'll check later tonight to see if it's still up. If it goes down then I'll try the pinging process idea. EDIT: It went down again. It lasted about a day. I've had them reboot, so now I'll try running "nohup ping -i 5 google.com &" and then disconnect. If it goes down again I'll come back. Hopefully someone will have some more ideas.

  Read the article

• How can I prevent Virtualmin from storing passwords in cleartext?

  - by Josh

  I am really surprised at this behavior. In Virtualmin, I can see the password for any SSH user by clicking the "(Show..)" link next to the "Password ( ) Leave unchanged" option in a variety of locations. I have found that the passwords for all users including users with SSH access are stored in cleartext files in /etc/webmin/... This seems like an unnecessary risk! How can I prevent Virtualmin from storing passwords in this manner?

  Read the article

• top does not run

  - by Horace Ho

  Sorry that I can't be very specific, only symtoms are provided: Monday morning a CentOS box, 1GB ram, Pentium 4 web server (thin, rails) does not response (too slow) to a browser of another PC ping it, ok ssh into it, ok a few minutes later, the web server is back to normal speed, serving web requests well ping it, ok ssh into it, ok however, top does not run what should I look at, about this 'top does not run' symptom? thx

  Read the article

• open-sshd service withou pam support !! How can I add pam support to sshd? Ubuntu

  - by marc.riera

  Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >