Search Results

Search found 37 results on 2 pages for 'poweroff'.

Page 1/2 | 1 2  | Next Page >

  • Prevent EC2 machine from halt, poweroff, shutdown

    - by Adam Matan
    Hi, EC2 Ubuntu servers erase all disk contents when being shut down. Following an unfortunate accident, I have decided to prevent the command-live halt, poweroff and shutdown. What's the best way to do it? I thought about renaming these commands (at /sbin) to something like HALT_RENAMED___ERASES_ALL_DISK_CONTENTS. Are there any files, other than the three listed above, that needs to be handled? I've noticed that halt and poweroff are merely links to reboot. Should reboot be renamed, too? Adam

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • PC shut downs automatically after 10-20 second. No POST screen, no beeps

    - by emzero
    I have this not-so-old computer that's not being used for a year or so. Specs: Motherboard: ASUS PN5-E SLI CPU: Intel Core2Duo E4300 RAM:2x2GB SuperTalent DDR2-800 VGA: Zogis GeForce 7950GT PSU: Vitsuba San-55-S 550w HD: No hardrives yet When I power on the computer, everything seem to start, but right away the whole system shuts down. I've removed and changed the RAM sticks, take out the VGA, everything I could think of. So what could it be causing this? The PSU? The motherboard is dead? The CPU? Any help to isolate the problem will be useful. Thanks PS: Please don't close the question, this could be helpful to anybody having a similar problem, even with different hardware. UPDATE I've removed the old thermal paste and apply a brand new one. I also cleaned every dust using a high pressure gas dust remover. Checked for bad capacitors, all of them seem ok. Opened the PSU, removed big giant dust balls, cleaned with high pressure dust remover. Still the same problem, but now it stays powered on for almost 20 seconds maybe. But no POST screen, no beeps at all, nothing. So I suspect it's a motherboard or PSU failure. Unfortunately I don't have an energy tester to test the PSU... Don't know what else to try. I don't have another 775-motherboard to test the CPU, RAM and VGA with it.

    Read the article

  • PC shut downs automatically after a second

    - by emzero
    I have this not-so-old computer that's not being used for a year or so. Specs: Motherboard: ASUS PN5-E SLI CPU: Intel Core2Duo E4300 RAM:2x2GB SuperTalent DDR2-800 VGA: Zogis GeForce 7950GT PSU: Vitsuba San-55-S 550w HD: No hardrives yet When I power on the computer, everything seem to start, but right away the whole system shuts down. I've removed and changed the RAM sticks, take out the VGA, everything I could think of. So what could it be causing this? The PSU? The motherboard is dead? The CPU? Any help to isolate the problem will be useful. Thanks PS: Please don't close the question, this could be helpful to anybody having a similar problem, even with different hardware.

    Read the article

  • What could possibly cause my computer to power down at random times?

    - by geoffreydv
    I have recently bought a new Power Supply and a new graphics card. My PC ran smoothly for a few months now but since a couple of days I'm having a strange problem. I am trying to isolate the problem to a specific piece of hardware (because if it's either the Power Supply or the Graphics card they are still under warranty). The problem started when I was playing a game (diablo 3). My PC suddenly powered down. I was unable to turn it on again by pressing the power button. I unplugged the power cable for a few seconds and plugged it back in. This time the pc powered on but the indication light turned orange instead of white as it normally does. The fans were not spinning and I did not see anything on my screen. After trying a couple of times I gave up. Two days later I tried again and this time the PC did boot up as usual. Everything looked okay until I tested if the problem was resolved by starting Diablo again. After about two minutes it powered down again as it did the first time. If I don't run any games my PC does power down after about 3-5 hours. Another fact that might be relevant: One time the PC did not shut down immediatly, instead first my graphics "powered down" but the music I was playing kept on playing. After about 20 seconds the pc powered down completely as usual. What I also noticed is that when I boot instantly after a power down, the chance of another power down occuring is much higher. Does anyone have an idea what could be causing this kind of behaviour or has a certain tool to diagnose the specific hardware parts? Thanks Specs: Memory: 6GB Processor: Intel i5 OS: Windows 7 64 bit The PC is a Dell Studio XPS 8100 with a replaced PSU and Graphics card: PSU: Corsair CX500 (500 watt) Graphics card: AMD Radeon 6850

    Read the article

  • Can a hard poweroff / outage / crash corrupt VMware snapshots?

    - by basic6
    Assuming a host system is running virtual machines (in VMware Workstation) and all their data is on a reliable storage (so no data corruption due to hdd failure). If that host crashes (kernel panic) while a vm is running, files on the virtual filesystem could be corrupted. But there's a snapshot (of the vm), taken before the crash. Is it safe to assume that reverting to the snapshot, the vm will be back in a clean state - or is there any way that this snapshot could have been corrupted by the crash?

    Read the article

  • How to power off a Debian Linux box via console

    - by Luke Puplett
    Brand new to Linux. I need to turn my box off and put it in my server room. The help here and everywhere seems not to work for me: http://debianhelp.co.uk/shutdown.htm I get: lukepuplett@uktnlx01:~$ poweroff -bash: poweroff: command not found lukepuplett@uktnlx01:~$ shutdown -bash: shutdown: command not found lukepuplett@uktnlx01:~$ modprobe apm -bash: modprobe: command not found lukepuplett@uktnlx01:~$ I also tried halt, reboot, goaway, and pleasejustwork.

    Read the article

  • C# Windows CE 5.0 error: Can't find entry point ExitWindowsEx in PInvoke DLL coredll

    - by JackN
    I need to programatically shutdown a Windows CE 5.0 tablet using Microsoft.NET SDK CompactFramework v2.0. I tried using the solution here but got the error message Can't find entry point ExitWindowsEx in PInvoke DLL coredll Is there a way to add ExitWindowsEx to my build? Do I need a different coredll? [Flags] public enum ExitFlags { Reboot = 0x02, PowerOff = 0x08 } [DllImport("coredll")] public static extern int ExitWindowsEx(ExitFlags flags, int reserved); private static void buttonShutdown_Click(object sender, EventArgs e) { ExitWindowsEx(ExitFlags.PowerOff, 0); } private static void buttonRestart_Click(object sender, EventArgs e) { ExitWindowsEx(ExitFlags.Reboot, 0); }

    Read the article

  • What are some good examples of Powernap scripts and its use?

    - by shootingstars
    I would like to use powernap for putting my media server into suspend mode, and I haven't been able to find any example /etc/powernap/action scripts out there, except these: one two three Does anybody have a good script or recommend particular techniques with its use? From the comments of the default /etc/powernap/action script: # You may do one of: # 1) Write your own custom script below and make this file executable, # calling some specific action, such as: # /usr/sbin/pm-suspend # /usr/sbin/pm-hibernate # /sbin/poweroff # echo 'I am wasting electricity' | mail [email protected] # 2) Replace this file with an executable script or binary # 3) Symlink this file to some other executable script or binary

    Read the article

  • HP DL380 reboot problems

    - by dvoina
    I have recently installed RHEL 5.3 on a HP DL 380 G5. Then I installed HP's PSP(Proliant Support Pack). Since then I cannot reboot the system anymore. The system just stays in "Broadcast message from root (tty0). The system is going for reboot NOW" Neither halt, poweroff, reboot nor init 6 works.

    Read the article

  • "/etc/init.d/networking restart" with non-root user

    - by bonchen
    I have a thin client with 112mb RAM which boots ubuntu server 12.04.1 from a usb drive with openbox and it is to be used by students to communicate with cisco equipment. And because of this the students need to be able to reconfigure the network interface and then restart it without a reboot using the only user - cisco. This is what I have so far: adduser cisco usermod -a -G dialout cisco chown root:cisco /etc/network/interfaces chmod 664 /etc/network/interfaces chmod u+s /sbin/shutdown chmod u+s /sbin/reboot chmod u+s /sbin/poweroff chmod u+s /run/network/if* chmod u+s /sbin/ifdown chmod u+s /sbin/ifup And when I run /etc/init.d/networking restart as cisco I get: *Reconfiguring network interfaces... rm: cannot remove `eth0.dhclient': Permission denied Failed to send flush request: Operation not permitted RTNETLINK answers: Operation not permitted Any ideas on how to get this working? Thanks!

    Read the article

  • wakeonlan from remote host

    - by takeshin
    I have setup wake on lan service on my server. Everything works fine on local area network: root@server$: poweroff user@local$ wakeonlan AA:BB:CC:DD:EE:FF and the server wakes up. AA:BB:CC:DD:EE:FF is a MAC address of my server, which has IP 192.168.1.2 and hostname: example.com. It is connected to the router, which has IP 192.168.1.1 (public: xxx.xxx.xxx.xxx) When the server is up, I can ping: ping example.com or login via ssh: ssh [email protected] So far, so good. Now I'm able to wake the server up from local area, but how to wake the server from the remote location? I tried: user@local$ wakeonlan -i xxx.xxx.xxx.xxx AA:BB:CC:DD:EE:FF, but it does not work (nothing happens;). Do I have to configure my router somehow to forward magic packets? How?

    Read the article

  • How to safely shutdown Guest OS in VirtualBox using command line

    - by Bakhtiyor
    I have Ubuntu 10.10 and using VirtualBox 3.2. As a Guest OS I have another Ubuntu in the VirtualBox. I am starting Guest Ubuntu automatically using following command once my Host Ubuntu boots: VBoxHeadless -startvm Ubuntu --vrdp on Then I can access to it with ssh or tsclient. Now I need to shutdown automatically Guest Ubuntu once I shutdown my Host Ubuntu. Does anybody know any safe method to automatically shutdown Guest Ubuntu with a command line? I have found out two ways one can shutdown Guest OS but I am not sure whether they are safe or not. Here are they: VBoxManage controlvm Ubuntu acpipowerbutton or VBoxManage controlvm Ubuntu poweroff

    Read the article

  • Ubuntu 12.04 does not power off

    - by G K
    I'm not able to power off Ubuntu, which was working fine a couple of days ago. When I click shut down, a blank screen appears and stays like that forever. It does not power off by itself and I'm forced to physically power off using the power button. I've even tried 'sudo shutdown now' and 'sudo shutdown -h now' and both don't seem to work! Please suggest some fix for this problem. Thanx in advance. Edit: Restart works fine. Also 'sudo poweroff' doesn't work!

    Read the article

  • 12.04 reboots rather than shutting down

    - by Luca
    I have a ruvo with a fresh installation of 12.04. When I try and shutdown the computer reboots. Until I upgraded (by doing a fresh install) I ran it with Ubuntu 10.04 and I didn't have this issue. I have tried sudo shutdown -h now sudo shutdown -P now sudo init 0 sudo poweroff All of these cause a reboot. I have added acpi=norq to my grub file as suggested by someone in the first post below. This is being used as a mythtv frontend and I would like the power button to shut it down. I have modified the button to perform a shutdown -h now, but this too causes a reboot. I have studied the posts below and tried some of these ideas, but with no luck so far. Why do I get a reboot instead of a shutdown? Ubuntu 12.04 not shutting down properly Stuck on reboot and shutdown Shutdown does not power off computer

    Read the article

  • why does chkdsk always report errors on a bad shutdown

    - by rep_movsd
    Once in a while, Windows XP hangs on my laptop (usually when going into standby or hibernate and occasionally on startup) and I have to forcefully poweroff. Ususally chkdsk never runs automatically (I thought it should know that the partitions have nit been unmounted and do that). I religiously run chkdsk without /F after bad shutdowns like this, and invariably it reports that the drive has unfixed errors and must be checked with /F and I do that, and more often than not, the chdsk that runs on startup does not report fixing anything. I have had times in the past (and not only just on this system) when not running chkdsk leads to some strange errors like files not opening even though they exist and inability to save certain files, so I make it a point to always chkdsk after bad shutdown. I never understood why this is : Isnt the whole point of a journalling filesystem like NTFS to avoid file system corruption and endless chkdsks? I even tried once disabling write caching to see if it made any difference, but to no avail....

    Read the article

  • Clonezilla is not able to clone a RAID 1 disk

    - by Adrian
    I have a HP Server DL320 G5. There are two SATA hard disks configured as RAID 1 through HP embedded RAID controller. Server OS is running GNU/Linux (Fedora) Server booted up with clonezilla live CD. The image will be stored on a NAS connected through NFS. Clonezilla could mount the NFS share and could see the two hard disks /dev/sda and /dev/sdb. I selected /dev/sda for disk cloning. However I could not see the cloning progress and got straight into a prompt for reboot, poweroff, command line I tried to select /dev/sdb but the same issue.

    Read the article

  • How can I perform a controlled shutdown of a virtualbox guest using VBoxManage?

    - by Bryan
    I'm currently testing Ubuntu 10.04, and have install the VirtualBox software. I have also installed Ubuntu 10.04 as a VirtualBox guest running on the host system. I've installed the VirtualBox Utils into the guest OS, as follows: sudo apt-get install virtualbox-ose-guest-utils What I want to be able to do is to initiate a controlled shutdown of the guest, from the host system using the VBoxManage command. I first tried this command: VBoxManage controlvm guest poweroff which worked, but didn't initiate a controlled shutdown, it effectively pulls the plug on the guest. I've since found that this command should do the trick: VBoxManage controlvm guest acpipowerbutton but this doesn't appear to do anything. Can anyone tell me what I'm doing wrong? p.s. I don't want to use SSH & Certificates to do this, as I'm also going to be running Windows guests, and I want the solution to work for all guests.

    Read the article

  • Give root password for maintenance

    - by Jevgeni Smirnov
    After entering shutdown now in terminal I get everything running normally and then: All processes ended withing 2 seconds...done INIT: Going single user INIT: Sending processes the TERM signal INIT: Sending processes the KILL signal Give root password for maintenance(or.... I press Ctrl+D, and it shows me login screen Debian. Shutdown through GUI works properly. UPDATE 1 It seems some process hangs. Moreover I'v managed to poweroff server through several retries. Recently i'v installed only ntp and ntpdate. Nothing more. I suppose it might be it conflicting with iptables.

    Read the article

  • How to properly shutdown or reboot a Unix/Linux server

    - by hatorade
    What is the correct way to turn off a Unix/Linux server? From my googling, I have learned (hopefully) the following: shutdown: I should use this, with the parameter -h to halt, or the parameter -r to reboot halt: halts the computer (stops the processor? does this physically turn the power of the computer off?). I think this will call shutdown if not at init0, otherwise just halts. reboot: if not at init6, calls shutdown, otherwise just reboots the computer. if all that is correct, then the only thing I can't figure out is what exactly 'halt' does. Does it just stop the processor but not turn the computer physically off? How do I "poweroff" the computer? Thanks

    Read the article

  • Where should custom vmware-tools scripts go

    - by Cylindric
    I have installed the VMWare Tools into a test Ubuntu guest, and it's created the standard scripts as expected: poweroff-vm-default poweron-vm-default resume-vm-default suspend-vm-default I add some custom actions to the scripts, but it says in the top of the file ########################################################################## # DO NOT modify this file directly as it will be overwritten the next # time the VMware Tools are installed. ########################################################################## So where should the custom scripts go, if I'm not supposed to modify these ones? scriptsdir="`dirname $0`/scripts/`basename $0`.d" if [ -d "$scriptsdir" ]; then for scriptfile in "$scriptsdir"/*; do [ -x "$scriptfile" ] && "$scriptfile" poweron-vm done fi

    Read the article

  • Shutdown button doesn't work in Windows 8

    - by Yob
    Some time ago I installed Windows 8 64bit ready-to-market version (as a student I had access to it before premiere). What I discovered is that the "shutdown" button doesn't work. When I want to shutdown the computer it simply logs me out. In order to turn off my machine I have to click "restart" and then simply press the poweroff button. I installed some updates but this issue is still not resolved. Is there any way to shutdown the computer in a normal way?

    Read the article

1 2  | Next Page >