Search Results

Search found 62 results on 3 pages for 'rj regenold'.

Page 1/3 | 1 2 3 | Next Page >

Why is my cat5e cable not okay?

- by torbengb

My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

Read the article
Does a USB to RJ-45 console cable exist?

- by Carl Flippin

I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

Read the article
regular expression for indian vehicle number

- by I Like PHP

i need validation for indian vehicle NUMBER here are condition list let expression is (x)(y)(z)(m)(a)(b)(c) 1. (x) contains only alphabets of length 2. 2. (y) may be - or single space ' ' 3. (z) contains only numbers of length 2 4. (m) may be or , or single space ' ' 5. length of (a) can be 2 or 3. contains alphanumeric value with minimum one alphabetic character. 6. (b) may be - or single space ' ' ( similar to (y) ) 7. (c) contains only numbers of length 4 i show you the various examples of vehicle number valid number RJ-14,NL-1234 RJ-01,4M-5874 RJ-07,14M-2345 RJ 07,3M 2345 RJ-07,3M-8888 RJ 07 4M 2345 RJ 07,4M 2933 invalid number RJ-07 3M 1234 ( both (y) and (b) should be same). RJ-07 M3-1234 ((a) must ends with alphabat). rj-07 M3-123 ( length of (c) must be 4).

Read the article
regular expression for indian vehicle number in javascript and php

- by I Like PHP

i need regular expression in java script as well as in PHP for Indian vehicle NUMBER here are conditions list let expression is (x)(y)(z)(m)(a)(b)(c) 1. (x) contains only alphabets of length 2. 2. (y) may be - or single space ' ' 3. (z) contains only numbers of length 2 4. (m) may be or , or single space ' ' 5. length of (a) can be 2 or 3. contains alphanumeric value with minimum one alphabetic character. 6. (b) may be - or single space ' ' ( similar to (y) ) 7. (c) contains only numbers of length 4 i show you the various examples of vehicle number valid number RJ-14,NL-1234 RJ-01,4M-5874 RJ-07,14M-2345 RJ 07,3M 2345 RJ-07,3M-8888 RJ 07 4M 2345 RJ 07,4M 2933 invalid number RJ-07 3M 1234 ( both (y) and (b) should be same). RJ-07 M3-1234 ((a) must ends with alphabat). rj-07 M3-123 ( length of (c) must be 4).

Read the article
"Modern" Ethernet over coax

- by Electrons_Ahoy

So, I've just bought a house. It's reasonably new - built in the early '00s. One of the features that got built in was a cable TV drop in every room. The cabling is gorgeous - there's even a wiring cabinet of sorts in a closet where the cables all tie together to the splitter to the outside line. Of course, my problem is that I only own the one TV. I do, however, own a few computers. What I would love to be able to do is drop a switch in the wiring closet and run 100/1000BASE-T ethernet over the coax in the walls I wouldn't otherwise be using. My fantasy would be if you could get some kind of adapter-plug-thing that would take a coax plug on one side and a cat5/RJ45 plug on the other. Had anyone else done this? Any suggestions? (There are a few other options that suggest themselves - first, I could just use the existing cabling channels and re-run cat5 or 6 through the walls. While tempting, that sounds like more work than I really want to put in, so I'm calling that Plan B. Also, I could just scare up a mess of old 10BASE2 cards and run the house on thinnet, all mid-90s style. While I think I'd get major style points for that, I don't think I can get a 10BASE2 adapter for the new laptop. Also, I have all these super-snazzy gigabit adaptors I'd like to be using. And so forth.)

Read the article
Can I directly open an MMF Cash Drawer through RJ-11 port?

- by roviuser

My aunt bought this cash drawer at an auction recently and has tasked me with figuring how to open it via a computer. We have the key (pictured) and can open it manually, but I'd like to be able to plug it directly into a computer and open it via some sort of program or script. It has a built in rj-11 cord coming out of the back of it. Initial research shows that it might usually be used with a printer, but I want to be able to connect it directly to the computer. Edit: this needs to be able to work with windows 7. Edit2: http://imgur.com/a/czEMs imgur gallery of the innards.

Read the article
A Question about .net Rfc2898DeriveBytes class?

- by IbrarMumtaz

What is the difference in this class? as posed to just using Encoding.ASCII.GetBytes(string object); I have had relative success with either approach, the former is a more long winded approach where as the latter is simple and to the point. Both seem to allow you to do the same thing eventually but I am struggling to the see the point in using the former over the latter. The basic concept I have been able to grasp is that you can convert string passwords into byte arrays to be used for e.g a symmetric encryption class, AesManaged. Via the RFC class but you get to use SaltValues and password when creating your rfc object. I assume its more secure but still thats an uneducated guess at best ! Also that it allows you to return byte arrays of a certain size, well something like that. heres a few examples to show you where I am coming from? byte[] myPassinBytes = Encoding.ASCII.GetBytes("some password"); or string password = "P@%5w0r]>"; byte[] saltArray = Encoding.ASCII.GetBytes("this is my salt"); Rfc2898DeriveBytes rfcKey = new Rfc2898DeriveBytes(password, saltArray); The 'rfcKey' object can now be used towards setting up the the .Key or .IV properties on a Symmetric Encryption Algorithm class. ie. RijndaelManaged rj = new RijndaelManaged (); rj.Key = rfcKey.Getbytes(rj.KeySize / 8); rj.IV = rfcKey.Getbytes(rj.Blocksize / 8); 'rj' should be ready to go ! The confusing part ... so rather than using the 'rfcKey' object can I not just use my 'myPassInBytes' array to help set-up my 'rj' object???? I have tried doing this in VS2008 and the immediate answer is NO ! but have you guys got a better educated answer as to why the RFC class is used over the other alternative I have mentioned above and why????

Read the article
replacing 3 Cisco Catalyst 4500

- by hoberion

Our network supplier recommends replacing our 3 cisco catalyst 4500's because they are EOL and dont speak OSPF (which we really want) Its not my area of expertise so I cant say for sure if we really need to replace these units but for my company the estimated costs of 250K euro is a huge problem. Is there any way to cut down on costs (without moving from cisco devices), I heard the 4500´s can speak ospf but would need an upgrade of sorts? edit: version: IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(20)EW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) supervisor: WS-X4013+ Cisco Catalyst 4500 Series Supervisor Engine II-Plus density: WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)

Read the article
Handling Special char such as ^ÛY, ^ÛR in java

- by RJ

Hi, Has anybody encountered special char such as ^ÛY, ^ÛR ? Q1. How do I do an ftp of the files containing these chars? The chars are not seen once I do a ftp on AIX (bi or ascii) and hence I am unable to see my program to replace these, working. Q2. My java program doesn't seem to recognise these or replace these if I search for these explicitly (^ÛY, ^ÛR ) in the file however a replace using regular expression seems to work (I could only see the difference in the length of the string). My program is executed on AIX. Any insights why java cannot recognise these? Q3. Does the Oracle database recognise these chars? An update is failing where my program indicates the string to be of lesser length and without these characters but the db complains "value too large for column" as the string to be updated contains these chars and hence longer. thanks in advance, RJ

Read the article
Where would a spam bot be located?

- by Tim

I have a hosted website using a free hosting service, I received an email this afternoon saying that I have been suspended because my account has been compromised. Basically, someone is using my email account to mass send spam. I've changed all the passwords and everything but when my Gmail pulls the emails from the host it's still downloading loads of spam messages that show like this: This message was created automatically by mail delivery software. A message that you sent could not be delivered to one or more of its recipients. This is a permanent error. The following address(es) failed: [email protected] SMTP error from remote mail server after end of data: host 198.91.80.251 [198.91.80.251]: 554 5.6.0 id=23634-03 - Rejected by MTA on relaying, from MTA([127.0.0.1]:10030): 554 Error: This email address has lost rights to send email from the system ------ This is a copy of the message, including all the headers. ------ Return-path: <[email protected]> Received: from keenesystems.com ([66.135.33.211]:2370 helo=server211) by absolut.x10hosting.com with esmtpsa (TLSv1:RC4-MD5:128) (Exim 4.77) (envelope-from <[email protected]>) id 1TGwSW-002hHe-Lc for [email protected]; Wed, 26 Sep 2012 13:35:44 -0500 MIME-Version: 1.0 Date: Wed, 26 Sep 2012 13:35:43 -0500 X-Priority: 3 (Normal) X-Mailer: Ximian Evolution 3.9.9 (8.5.3-6) Subject: New staff members wanted at Auction It Online From: [email protected] Reply-To: [email protected] To: "Nadia Monti" <[email protected]> Content-Type: text/plain Content-Transfer-Encoding: quoted-printable Message-ID: <OUTLOOK-IDM-9aed7054-6a3e-e1a4-1d5c-3e73377652a6@server211> Date : 26 September 2012=0ATime : 13:35=0ASender : Dennise Halcomb Head = Office Manager of RJ Auction Drop-Off Int.=0A=0ANice to meet you Nadia M= onti=0A=0ARJ ADO Ltd., a USA based company, offers a significant amount = of goods worldwide for our customers on eBay and other auction venues. = Our company's main target is to provide a suitable and cost-effective se= rvice for any person, company or fundraising company. The main purpose o= f the administrative assistant / sales support representative is to cont= ribute to the sales force and add convenience to our cost-effective serv= ice dedicated to individuals, businesses, and organizations worldwide. O= ur HR department obtained your resume from one of the various job-orient= ed websites just to offer you this post.=0A=0AWorking Schedule: This is = a part time and home-based offer. You won't need to spend more than 3 ho= urs each day. Your =0Aschedule will be flexible.=0A=0ASalary: At the end= of the trial period (it lasts for 1 month) you will be paid 1,800 EUR. = With the average volume of clients your overall income will raise up to = 3,000 EUR per month. After the trial period is over your base salary wil= l grow up to 2,500 EUR per month, so you will earn 5% commission from th= e transactions completed.=0A=0AWhere?: Italy Wide. As it is a stay at ho= me position all the communication will be carried out via email and via = phone.=0A=0ARequirements: Access to the internet during the workday and = basic microsoft office skills are needed. Basic knowledge of English is = required (most of the contacts will be in English).=0A=0ACosts and Fees:= There are NO costs at any time for our employees. All fees related to t= his position are covered by the RJ ADO Co. Ltd..=0A=0AFurther Hiring Pro= cess: If you are interested in position we offer, please reply to this e= mail and send us the copy of your resume for verification.=0A=0AAfter re= viewing all of the received applications we will reply to successful app= licants only. Then we'll offer to these successful applicants a position= within our firm on a trial period basis for one month beginning from th= e date you sign a trial agreement. During this trial period you will rec= eive full guidance and support. Employees on a one monthly trial period = are evaluated at least one week prior to the end of their trial. During = the trial, your supervisor can recommend termination. At the end of the = trial period, the supervisor can offer continued employment, extension o= f trial period, or termination. After the trial period you may ask for m= ore hours or continue full-time.=0A=0AIf you are interested in this posi= tion, just reply to this email and send any questions you have and the c= opy of your resume for verification.=0A=0AThank You,=0AHR-Manager of RJ = ADO Co. Ltd.=0A=0APermission Settings=0AYou have been referred to RJ Auc= tion Drop-Off If you feel you received this email in error or do not wis= h to receive future messages, please reply to this message with "remove"= in the subject field. We will immediately update our database according= ly. =0AWe apologize for any inconvenience caused.=0A=0ARJ Auction Drop-O= ff Co. Ltd. I'm not aware of how this has happened. I'm not sure how anyone could have got hold of my password. It's a simple wordpress install, at some point recently my host went down and there was a fresh install of wordpress with default admin accounts, I have a feeling it could be something to do with this. My question is, even though I've changed all my passwords it's all still happening, is there annywhere in paticular this script would be stored on my host. I really can't deal with having my hosting account suspended and my email account sending all this spam.

Read the article
Grails Liferay portlet not invoking action

- by RJ Regenold

I am trying to create a simple portlet for Liferay 5.2.2 using Grails 1.2.1 with the grails-portlets 0.7 and grails-portlets-liferay 0.2 plugins. I created and deployed a stock portlet (just updated title, description, etc...). It deploys correctly and the view renders correctly. However, when I submit the default form that is in view.gsp it never hits the actionView function. Here are the relevant code bits: SearchPortlet.groovy class SearchPortlet { def title = 'Search' def description = ''' A simple search portlet. ''' def displayName = 'Search' def supports = ['text/html':['view', 'edit', 'help']] // Liferay server specific configurations def liferay_display_category = 'Category' def actionView = { println "In action view" } def renderView = { println "In render view" //TODO Define render phase. Return the map of the variables bound to the view ['mykey':'myvalue'] } ... } view.gsp <%@ taglib uri="http://java.sun.com/portlet" prefix="portlet" %> <div> <h1>View Page</h1> The map returned by renderView is passed in. Value of mykey: ${mykey} <form action="${portletResponse.createActionURL()}"> <input type="submit" value="Submit"/> </form> </div> The tomcat terminal prints In render view whenever I view the portlet, and after I press the submit button. It never prints the In action view statement. Any ideas? Update I turned on logging and this is what I see whenever I click the submit button in the portlet: [localhost].[/gportlet] - servletPath=/Search, pathInfo=/invoke, queryString=null, name=null [localhost].[/gportlet] - Path Based Include portlets.GrailsDispatcherPortlet - DispatcherPortlet with name 'Search' received render request portlets.GrailsDispatcherPortlet - Bound render request context to thread: com.liferay.portlet.RenderRequestImpl@7a158e portlets.GrailsDispatcherPortlet - Testing handler map [org.codehaus.grails.portlets.GrailsPortletHandlerMapping@1f06283] in DispatcherPortlet with name 'Search' portlets.GrailsDispatcherPortlet - Testing handler adapter [org.codehaus.grails.portlets.GrailsPortletHandlerAdapter@74f72b] portlets.GrailsPortletHandlerAdapter - portlet.handleMinimised not set, proceeding with normal render portlet.SearchPortlet - In render view portlets.GrailsPortletHandlerAdapter - Couldn't resolve action view /search/null.gsp portlets.GrailsPortletHandlerAdapter - Trying to render mode view /search/view.gsp portlets.GrailsDispatcherPortlet - Setting portlet response content type to view-determined type [text/html;charset=ISO-8859-1] [localhost].[/gportlet] - servletPath=/WEB-INF/servlet/view, pathInfo=null, queryString=null, name=null [localhost].[/gportlet] - Path Based Include portlets.GrailsDispatcherPortlet - Cleared thread-bound render request context: com.liferay.portlet.RenderRequestImpl@7a158e portlets.GrailsDispatcherPortlet - Successfully completed request The fourth line in that log snippet says Bound render request..., which I don't understand because the action in the form that is in the portlet is to the action url. I would've thought that should be an action request.

Read the article
ASP.NET MVC Consume JSONResult in Bing Maps API

- by rockinthesixstring

I know there are a few topics on this, but I seem to be fumbling my way through with no results. I'm trying to use a controller to return JSON results to my Bin Maps functions. Here's what I have for my controller (yes it is properly returning JSON data. Function Regions() As JsonResult Dim rj As New List(Of RtnJson)() rj.Add(New RtnJson("135 Bow Meadows Drive, Cochrane, Alberta", "desc", "title")) rj.Add(New RtnJson("12 Bowridge Dr NW, Calgary, Alberta, Canada", "desc2", "title2")) Return Json(rj, JsonRequestBehavior.AllowGet) End Function Then in my script I have this, but it's not working. <script type="text/javascript"> var map = null; var centerLat = 51.045 ; var centerLon = -114.05722; var json_object = $.getJSON("<%: Url.Action("Regions", "Events")%>"); function LoadMap() { map = new VEMap('bingMap'); map.LoadMap(new VELatLong(centerLat, centerLon), 10); $.each(json_object, function () { alert(this.address); //this alert is returning "address is undefined" StartGeocoding(this.address, this.title, this.desc); }); } function StartGeocoding(address, title, desc) { map.Find(null, // what address, // where null, // VEFindType (always VEFindType.Businesses) null, // VEShapeLayer (base by default) null, // start index for results (0 by default) null, // max number of results (default is 10) null, // show results? (default is true) null, // create pushpin for what results? (ignored since what is null) true, // use default disambiguation? (default is true) false, // set best map view? (default is true) GeocodeCallback); // call back function } function GeocodeCallback(shapeLayer, findResults, places, moreResults, errorMsg) { var bestPlace = places[0]; // Add pushpin to the *best* place var location = bestPlace.LatLong; var newShape = new VEShape(VEShapeType.Pushpin, location); var desc = "Latitude: " + location.Latitude + "<br>Longitude:" + location.Longitude; newShape.SetDescription(desc); newShape.SetTitle(bestPlace.Name); map.AddShape(newShape); } $(document).ready(function () { LoadMap(); }); </script>

Read the article
internet connection occasionally stops, but can still ping .com sites

- by rj

hi, every half hour or so, for 1-2 minutes my browser will stop navigating to sites, "waiting for ... to respond.." within 2 minutes i will be able to connect to sites and browse like normal again. weird thing is, while i cannot connect to sites, i get ping replies from any .com i type in. this happens on my home wireless network, using FF and IE on a win7 desktop AND FF on an ubuntu laptop the network is wpa2 secured, these are the only connections.

Read the article
please demystify the 10Gb ethernet interfaces, cables

- by maruti

this really is a Dell question but tempted to ask the experts @ serverfault. choosen a Dell powerconnect 8024 10GbE switch. per the spec sheet this has 10GbaseT ports. "24x 10GBASE-T (10Gb/1Gb/100Mb) with 4x Combo Ports of SFP+ (10Gb/1Gb) or 10GBASE-T" the HBA on my storage server has 10G CX4 copper ports Dell does not sell any cables and this adds to my confusion. from the picture Dell 8024 seems to have RJ-45 type ports on the front panel? my question: is it a RJ-45 + CX4 cable or CX4 + CX4 cable?

Read the article
Cabling: What to keep in stock?

- by pehrs

I have worked a few different places, each one with a different solution, so I would like to hear your suggestions and ideas. I am looking at a situation with multiple server-rooms. We have a mixture of copper (both ethernet and telephone), multi-mode fibre and single-mode fibre. We have all types of connectors: RJ-11, RJ-45, LC, SC, FC, SMA and several I probably forgot about. We have a lot of people working in the area, and keeping track of cables is turning into a full time job. So, here are a the questions: What types and lengths of cable do you keep in stock on site? Do you make your own or buy pre-made? Adapters? Dampeners? How do you manage cable inventory? How do you label the cables? Any other tricks to stop this from driving me crazy?

Read the article
Wall jacks to patch panel?

- by rj454me

OK, I'm by no means a seasoned networking pro and I had no say so in the design of our current server room which is in dire need of an extreme makeover. Basically, in our server room we have 12 wall plates with 4 RJ-45 ports on each - 48 total RJ-45 ports. From these 48 ports is a spaghetti bowl of network cables feeding our servers located in a rack - there is no patch panel currently, just straight from the wall jack to each server. What I was wondering is, is it feasible to mount a 48 port patch panel in our server rack and feed into this patch panel from the wall jacks (of course nicely routing this cable through some new cable trays)? We really don't have the funds to mount the patch panel and have it fed directly from the switches in the telcom closet which is several hundred feet away. Current: Switch (Telcom Closet) - Wall Jacks - Servers Proposed: Switch (Telcom Closet) - Wall Jacks - Patch Panel - Servers

Read the article
Using USB to Ethernet with Linux Ubuntu 12.04

- by Sriram

Being a newbie, Please excuse if the technical Jargon used is not an universally accepted one :) I have a particular device (say device A) whose USB2.0 driver is available from Linux community. Linux UBUNTU12.04 based PC is able to detect that device via the available driver. My requirement is to ensure that PC can exchange the command as well as data with the device A over TCP/IP packets (In other words, instead of just a USB Based driver, there should be a TCP/IP wrapper over the device USB driver and still does the same job as the USB driver was doing before) Bought an USB (Female) to RJ-45 adapter,connected Device A (male) USB to the USB Female end of the adapter and the Ethernet end connected to the router. PC also is connected to the same router so that both Device A and the PC have the IP address in the same subnet range. So the packets produced by the device A can be routed to the PC via some binding( not sure how I can achieve this, but conceptual idea) Here are the issues I can see as of now 1) USB to RJ-45 is just a hardware signal conversion and not a NIC in itself and hence no MAC/IP ADDRESS assigned. Can we bind a virtual NIC created in PC with this connector? 2) Any available USB TO IP command as well as data translation wrappers available? e.g. command for the device A on Ethernet converted to command for the device A on USB which is then acted upon the device as a command from the USB driver There is some missing link in my understanding and hence it would be of great help if you can bounce off some ideas on how I can take this forward so that Device A and PC exchange data over IP. Thanks and Regards, Sriram

Read the article
Using javascript to limit survey choices to three unique values

- by leanne

I'm required to use a limited survey application, and have to adapt the provided code to meet more advanced functionality. I need to create a weighted ranking question, so users can select their top three choices and the data will go into the survey application and be accessible in the survey reports. The application only supports 2 types of questions (text fill & multiple choice) but I can alter the code, as long as it still sends the form data back to the survey application. The code is set up so it will show a drop-down menu of 0-3 for each option. Now I want to limit the user's choices so they can only select one "1" "2" or "3", three choices total. Ideally, if the user already had "2" selected for one option and they tried to select it for another option, it would set the first "2" as "0" or blank. Is this possible to do with javascript? If so, does anyone know of a site that might show code like this, or provide similar enough examples that I could adapt it? Current code here: <html> <head><title>Survey</title></head>  <link href="---" rel="stylesheet" type="text/css"> <body bgcolor="#3c76a3">  <table border="0" align="center" cellpadding="0" cellspacing="0" style="background-attachment: scroll; background-color: #3c76a3; background-repeat: no-repeat; background-position: left top;" bgcolor="#3c76a3" topmargin="0" marginwidth="0" marginheight="0" width="100%" height="100%"> <tr> <td> <table border="0" align="center" cellpadding="0" cellspacing="0" id="survey"> <tr> <td><p> </p>  <form name="survey" action="---" method="POST"> <FONT face="Verdana, Arial, Helvetica, sans-serif"> <b>survey</b><hr>  <input type=hidden name="Buy R.J. a DeLorean_multiple_answers" value="one"> <font size=2><select name="Buy R.J. a DeLorean" SIZE=1> <option value=""> <option value="0">0 <option value="1">1 <option value="2">2 <option value="3">3 </select></font> <input type="hidden" name="Buy R.J. a DeLorean_help" value=""> <b><font size=2>Buy R.J. a DeLorean</font></b> <hr size=1>  <input type=hidden name="Fill Lisa's office with marshmallows._multiple_answers" value="one"> <font size=2><select name="Fill Lisa's office with marshmallows." SIZE=1> <option value=""> <option value="0">0 <option value="1">1 <option value="2">2 <option value="3">3 </select></font> <input type="hidden" name="Fill Lisa's office with marshmallows._help" value=""> <b><font size=2>Fill Lisa's office with marshmallows.</font></b> <hr size=1>  <input type=hidden name="Install a beer fridge in everyone's filing cabinets._multiple_answers" value="one"> <font size=2><select name="Install a beer fridge in everyone's filing cabinets." SIZE=1> <option value=""> <option value="0">0 <option value="1">1 <option value="2">2 <option value="3">3 </select></font> <input type="hidden" name="Install a beer fridge in everyone's filing cabinets._help" value=""> <b><font size=2>Install a beer fridge in everyone's filing cabinets.</font></b> <hr size=1>  <input type=hidden name="Buy a company Cessna_multiple_answers" value="one"> <font size=2><select name="Buy a company Cessna" SIZE=1> <option value=""> <option value="0">0 <option value="1">1 <option value="2">2 <option value="3">3 </select></font> <input type="hidden" name="Buy a company Cessna_help" value=""> <b><font size=2>Buy a company Cessna</font></b><br> <hr size=1>  <input type=hidden name="Replace Conf2's chairs with miniature ponies._multiple_answers" value="one"> <font size=2><select name="Replace Conf2's chairs with miniature ponies." SIZE=1> <option value=""> <option value="0">0 <option value="1">1 <option value="2">2 <option value="3">3 </select></font> <input type="hidden" name="Replace Conf2's chairs with miniature ponies._help" value=""> <b><font size=2>Replace Conf2's chairs with miniature ponies.</font></b> <hr size=1> <input type="hidden" name="question_names" value="{Buy R.J. a DeLorean} {Fill Lisa's office with marshmallows.} {Install a beer fridge in everyone's filing cabinets.} {Buy a company Cessna} {Replace Conf2's chairs with miniature ponies.}"> <p align="right"><input type="image" BORDER=0 title="Save Changes" alt="Save Changes" src="---" name="button_save_changes"> <input type="hidden" name="showconfirm" value="T"> <input type="hidden" name="showresults" value="F"> <input type="hidden" name="preventdupesmemberid" value="T"> <input type="hidden" name="preventdupesip" value="F"> <input type="hidden" name="numberquestions" value="F"> <input type="hidden" name="destinationurl" value=""> <input type="hidden" name="original_survey_id" value="62"> </form>  </td> </tr> </table> </td> </tr> </table>  </body> </html>

Read the article
Stumped by "The remote server returned an error: (403) Forbidden" with WCF Service in https

- by RJ

I have a WCF Service that I have boiled down to next to nothing because of this error. It is driving me up the wall. Here's what I have now. A very simple WCF service with one method that returns a string with the value, "test". A very simple Web app that uses the service and puts the value of the string into a label. A web server running IIS 6 on Win 2003 with a SSL certificate. Other WCF services on the same server that work. I publish the WCF service to it's https location I run the web app in debug mode in VS and it works perfectly. I publish the web app to it's https location on the same server the WCF service resides under the same SSL certificate I get, "The remote server returned an error: (403) Forbidden" I have changed almost every setting in IIS as well as the WCF and Web apps to no avail. I have compared setting in the WCF services that work and everything is the same. Below are the setting in the web.config for the WCF Service and the WEB app: It appears the problem has to do with the Web app but I am out of ideas. Any ideas: WCF Service: <system.serviceModel> <bindings> <client /> <services> <service behaviorConfiguration="Ucf.Smtp.Wcf.SmtpServiceBehavior" name="Ucf.Smtp.Wcf.SmtpService"> <host> <baseAddresses> <add baseAddress="https://test.net.ucf.edu/webservices/Smtp/" /> </baseAddresses> </host> <endpoint address="" binding="wsHttpBinding" contract="Ucf.Smtp.Wcf.ISmtpService" bindingConfiguration="SSLBinding"> <identity> <dns value="localhost"/> </identity> </endpoint> <endpoint address="mex" binding="mexHttpsBinding" contract="IMetadataExchange"/> </service> </services> <behaviors> <serviceBehaviors> <behavior name="Ucf.Smtp.Wcf.SmtpServiceBehavior"> <serviceMetadata httpsGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="true" httpsHelpPageEnabled="True"/> </behavior> </serviceBehaviors> </behaviors> Web App: <system.serviceModel> <bindings><wsHttpBinding> <binding name="WSHttpBinding_ISmtpService" closeTimeout="00:01:00" openTimeout="00:01:00" receiveTimeout="00:10:00" sendTimeout="00:01:00" bypassProxyOnLocal="false" transactionFlow="false" hostNameComparisonMode="StrongWildcard" maxBufferPoolSize="524288" maxReceivedMessageSize="65536" messageEncoding="Text" textEncoding="utf-8" useDefaultWebProxy="true" allowCookies="false"> <readerQuotas maxDepth="32" maxStringContentLength="8192" maxArrayLength="16384" maxBytesPerRead="4096" maxNameTableCharCount="16384" /> <reliableSession ordered="true" inactivityTimeout="00:10:00" enabled="false" /> <security mode="Transport"> <transport clientCredentialType="None" proxyCredentialType="None" realm="" /> <message clientCredentialType="Windows" negotiateServiceCredential="true" establishSecurityContext="true" /> </security> </binding> <client> <endpoint address="https://net228.net.ucf.edu/webservices/smtp/SmtpService.svc" binding="wsHttpBinding" bindingConfiguration="WSHttpBinding_ISmtpService" contract="SmtpService.ISmtpService" name="WSHttpBinding_ISmtpService"> <identity> <dns value="localhost" /> </identity> </client> </system.serviceModel>

Read the article
How do I update ItemTemplate after scrambling ObservableCollection(Of ObservableCollection(Of object

- by user342195

I am learning vb.net, wpf and xaml with the help of sites like this one. The project I am currently working on is a 4 x 4 slide puzzle. I cannot get the buttons in the grid to scramble to start a new game when calling a new game event. Any help will be greatly appreciated. If no answer is can be provide, a good resource to research would help as well. Thank you for your time. XAML: <Window x:Class="SlidePuzzle" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="Slide Puzzle" Height="391" Width="300" Name="wdw_SlidePuzzle"> <Window.Resources> <DataTemplate x:Key="DataTemp_PuzzleButtons"> <Button Content="{Binding C}" Height="50" Width="50" Margin="2" Visibility="{Binding V}"/> </DataTemplate> <DataTemplate x:Key="DataTemplate_PuzzleBoard"> <ItemsControl ItemsSource="{Binding}" ItemTemplate="{DynamicResource DataTemp_PuzzleButtons}"> <ItemsControl.ItemsPanel> <ItemsPanelTemplate> <Canvas/> </ItemsPanelTemplate> </ItemsControl.ItemsPanel> <ItemsControl.ItemContainerStyle> <Style> <Setter Property="Canvas.Top" Value="{Binding Path=Y}" /> <Setter Property="Canvas.Left" Value="{Binding Path=X}" /> </Style> </ItemsControl.ItemContainerStyle> </ItemsControl> </DataTemplate> </Window.Resources> <DockPanel Name="dpanel_puzzle" LastChildFill="True"> <WrapPanel DockPanel.Dock="Bottom" Margin="5" HorizontalAlignment="Center"> <Button Name="bttnNewGame" Content="New Game" MinWidth="75" Margin="4" Click="NewGame_Click"></Button> <Button Name="bttnSolveGame" Content="Solve" MinWidth="75" Margin="4"></Button> <Button Name="bttnExitGame" Content="Exit" MinWidth="75" Margin="4" Click="ExitGame_Click"></Button> </WrapPanel> <WrapPanel DockPanel.Dock="Bottom" Margin="5" HorizontalAlignment="Center"> <Label>Score:</Label> <TextBox Name="tb_Name" Width="50"></TextBox> </WrapPanel> <StackPanel Name="SlidePuzzlePnl" HorizontalAlignment="Center" VerticalAlignment="Center" Height="206" Width="206" > <ItemsControl x:Name="lst" ItemTemplate="{DynamicResource DataTemplate_PuzzleBoard}"/> </StackPanel> </DockPanel> VB: Imports System.Collections.ObjectModel Class SlidePuzzle Dim puzzleColl As New ObservableCollection(Of ObservableCollection(Of SlidePuzzleBttn)) Dim puzzleArr(3, 3) As Integer Private Sub Window1_Loaded(ByVal sender As System.Object, ByVal e As System.Windows.RoutedEventArgs) Handles MyBase.Loaded For i As Integer = 0 To 3 puzzleColl.Add(New ObservableCollection(Of SlidePuzzleBttn)) For j As Integer = 0 To 3 puzzleArr(i, j) = (i * 4) + (j + 1) puzzleColl(i).Add(New SlidePuzzleBttn((i * 4) + (j + 1))) puzzleColl(i)(j).X = j * 52 puzzleColl(i)(j).Y = i * 52 Next Next lst.ItemsSource = puzzleColl End Sub Private Sub NewGame_Click(ByVal sender As System.Object, ByVal e As System.Windows.RoutedEventArgs) Dim rnd As New Random Dim ri, rj As Integer Dim temp As Integer For i As Integer = 0 To 3 For j As Integer = 0 To 3 ri = rnd.Next(0, 3) rj = rnd.Next(0, 3) temp = puzzleArr(ri, rj) puzzleArr(ri, rj) = puzzleArr(i, j) puzzleArr(i, j) = temp puzzleColl(i)(j).X = j * 52 puzzleColl(i)(j).Y = i * 52 puzzleColl(i)(j).C = puzzleArr(i, j) Next Next End Sub End Class Public Class SlidePuzzleBttn Inherits DependencyObject Private _c As Integer Private _x As Integer Private _y As Integer Private _v As String Public Shared ReadOnly ContentProperty As DependencyProperty = DependencyProperty.RegisterAttached("_c", GetType(String), GetType(SlidePuzzleBttn), New UIPropertyMetadata("")) Public Sub New() _c = 0 _x = 0 _y = 0 _v = SetV(_c) End Sub Public Sub New(ByVal cVal As Integer) _c = cVal _x = 0 _y = 0 _v = SetV(cVal) End Sub Public Property C() As Integer Get Return _c End Get Set(ByVal value As Integer) _c = value End Set End Property Public Property X() As Integer Get Return _x End Get Set(ByVal value As Integer) _x = value End Set End Property Public Property Y() As Integer Get Return _y End Get Set(ByVal value As Integer) _y = value End Set End Property Public Property V() As String Get Return _v End Get Set(ByVal value As String) _v = value End Set End Property Private Function SetV(ByRef cVal As Integer) As String If cVal = 16 Then Return "Hidden" Else Return "Visible" End If End Function End Class

Read the article
Newbie Objective C developer question

- by R.J.

I have been looking everywhere for an answer to this question - perhaps I'm looking in the wrong places. Also, I'm brand new to Objective C although I have around 10 years of experience as a developer. for this code: [receiver makeGroup:group, memberOne, memberTwo, memberThree]; what would the method definition look like? - (void)makeGroup:(Group *)g, (NSString *)memberOne, ...? Thanks for any help you can provide. I know this is probably very simple... Thanks, R

Read the article
Can I create a custom roleprovider through a WCF service?

- by RJ

I have a web application that accesses a database through a wcf service. The idea is to abstract the data from the web application using the wcf service. All that works fine but I am also using the built in roleprovider using the SqlRoleManager which does access the aspnetdb database directly. I would like to abstract the roleprovider by creating a custom roleprovider in a wcf service and then accessing it through the wcf service. I have created the custom role provider and it works fine but now I need to place it in a wcf service. So before I jump headlong into trying to get this to work through the WCF service, I created a second class in the web application that accessed the roleprovider class and changed my web config roleprovider parameters to use that class. So my roleprovider class is called, "UcfCstRoleProvider" and my web.config looks like this: <roleManager enabled="true" defaultProvider="UcfCstRoleProvider"> <providers> <add name="UcfCstRoleProvider" type="Ucf.Security.Wcf.WebTests.UcfCstRoleProvider, Ucf.Security.Wcf.WebTests" connectionStringName="SqlRoleManagerConnection" applicationName="SMTP" /> </providers> </roleManager> My class starts like this: public class UcfCstRoleProvider : RoleProvider { private readonly WindowsTokenRoleProvider _roleProxy = new WindowsTokenRoleProvider(); public override string ApplicationName { get { return _roleProxy.ApplicationName; } set { _roleProxy.ApplicationName = value; } } As I said, this works fine. So the second class is called BlRoleProvider that has identical properties and parameters as the roleprovide but does not implement RoleProvider. I changed the web.config to point to this class like this: <roleManager enabled="true" defaultProvider="BlRoleProvider"> <providers> <add name="UcfCstRoleProvider" type="Ucf.Security.Wcf.WebTests.BlRoleProvider, Ucf.Security.Wcf.WebTests" connectionStringName="SqlRoleManagerConnection" applicationName="SMTP" /> </providers> </roleManager> But I get this error. "Provider must implement the class 'System.Web.Security.RoleProvider'." I hope I have explained well enough to show what I am trying to do. If I can get the roleprovider to work through another class in the same application, I am sure it will work through the WCF service but how do I get past this error? Or maybe I took a wrong turn and there is a better way to do what I want to do??

Read the article
Add double tap action (presentModalViewController) to UISCOLLVIEW

- by R.J.

I have been wrestling this issue for a while now and cannot seem to get the following "touchesEnded" method to execute within a UISCROLLVIEW. I have read on many of the forums that UISCROLLVIEW will take control of all touch events unless it is subclassed, but I cannot seem to get the code right (still new to the SDK). Basically I have a scrollview made uo with several UIIMAGEVIEW's and currenlty have scrolling with paging (much like the photo app). I have been studying the SCROLLING MADDNESS example without success. All I want to do is anywhere in the UISCROLLVIEW have the user double tap to presentModalViewController back to my info page (i.e.) (void)touchesEnded:(NSSet *)touches withEvent:(UIEvent *)event { NSSet *allTouches = [event allTouches]; switch ([allTouches count]) { case 1: {// One finger touch UITouch *touch = [[allTouches allObjects] objectAtIndex:0]; if ([touch tapCount] == 2) {InfoButtonViewController *scroll = [[InfoButtonViewController alloc] initWithNibName:nil bundle:nil]; scroll.modalTransitionStyle = UIModalTransitionStyleFlipHorizontal; [self presentModalViewController:scroll animated:YES]; [scroll release]; } } } } Any code assistance would be greatly appreciated. The UISCROLLVIEW is implemented as follows (let me know if I need to provide additional details). Thank you in advance... MyViewController.h @interface MyViewController : UIViewController { } @end

Read the article
WCF REST POST XML

- by RJ

Whats the best way that I can create wcf rest post that accepts xml document(with out any query string)?

Read the article
Programmatically add IP(s) or domain(s) to Relay Restrictions in SMTP Virtual Server on IIS 6

- by RJ

I have been given a task to create an admin page to programmatically add IPs or domains to a SMTP Relay Restrictions using C#. I spent some time researching this since yesterday and finally traced this down to a few posts on several website that use the System.DirectoryServices.DirectoryEntr class. Using the examples I found, I can add or deny IPs or domains under Connection control but not Relay Restrictions. What would be the commands in C# to add IPs to the Relay Restrictions? Below is a pic of the GUI in IIS for reference.-

Read the article

1 2 3 | Next Page >