Search Results

Search found 3956 results on 159 pages for 'scripting bridge'.

Page 1/159 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• linux container bridge filters ARP reply

  - by Dani Camps

  I am using kernel 3.0, and I have configured a linux container that is bridged to a tap interface in my host computer. This is the bridge configuration: :~$ brctl show bridge-1 bridge name bridge id STP enabled interfaces bridge-1 8000.9249c78a510b no ns3-mesh-tap-1 vethjUErij My problem is that this bridge is dropping ARP replies that come from the ns3-mesh-tap-1 interface. Instead, if I statically populate the ARP tables and ping directly everything works, so it has to be something related to ARP. I have read about similar problems in related posts, and I have tried with the solutions explained therein but nothing seems to work. Specifically: ~$ grep net.bridge /etc/sysctl.conf net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 arptables and ebtables are not installed. iptables FORWARD is all set to accept: Chain FORWARD (policy ACCEPT) target prot opt source destination The bridged interfaces are set to PROMISC: ~$ ifconfig ns3-mesh-tap-1 Link encap:Ethernet HWaddr 1a:c7:24:ef:36:1a ... UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 vethjUErij Link encap:Ethernet HWaddr aa:b0:d1:3b:9a:0a .... UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 The macs learned by the bridge are correct (checked with brctl showmacs). Any insight on what I am doing wrong would be greatly appreciated. Best Regards Daniel

  Read the article

• 6-core Sandy Bridge-E vs. 4-core Ivy Bridge

  - by Alexander Ilyin

  I am currently choosing between Intel Core i7-3770 (quad, Ivy) and Intel Core i7-3930K (6 cores, Sandy Bridge-E). This machine will be used for both work (Adobe, Autodesk software, graphic and coding-related) and gaming. Even if some applications I will use are capable to utilize all 6 cores at once, is it worth preferring Sandy Bridge-E to newer Ivy Bridge? Games aren't and probably will perform better on Ivy, won't they? 6-core is also twice as expensive as a quad Ivy.

  Read the article

• Script to setup Ubuntu as a wireless access point on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless access point. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• Script to setup ubuntu as a wireless accesspoint on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless accesspoint. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• What does (Lua) game scripting mean?

  - by Gerenuk

  I've read that Lua is often used for embedded scripting and in particular game for scripting. I find it hard to picture how it is used exactly. Can you describe why and for which features and for which audience it is used? This questions isn't specifically addressing Lua, but rather any embedded scripting that serves a purpose similar to Lua scripting. Is it used for end-users to make custom adjustments? Is it used for game developers to speed up creation of game logic (levels, AI, ...)? Is it used to script game framework code since scripting can be faster? Basically I'm wondering how deep between plain configuration and framework logic such scripting usage goes. And how much scripting is done. A few configuration lines or a considerable amount?

  Read the article

• openwrt uses a single interface bridge?

  - by timbo

  My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

  Read the article

• My laptop can not access internet after setup bridge with wired NIC and wireless NIC

  - by Victor S

  I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup steps: $ sudo killall hostapd hostapd: no process found $ sudo hostapd -B hostapd.conf Configuration file: hostapd.conf Using interface wlan0 with hwaddr 00:26:5e:e8:4f:8e and ssid 'myAP' $ sudo brctl addbr br0 device br0 already exists; can't create bridge with the same name $ sudo ifconfig eth0 0.0.0.0 up $ sudo ifconfig wlan0 0.0.0.0 up $ sudo brctl addif br0 eth0 $ sudo brctl addif br0 wlan0 device wlan0 is already a member of a bridge; can't enslave it to bridge br0. $ sudo ifconfig br0 192.168.1.110 netmask 255.255.255.0 $ sudo route add default gw 192.168.1.1

  Read the article

• tap interfaces always disabled in linux bridge

  - by Dani Camps

  I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

  Read the article

• Most transparent way to connect two LANS using a WET610N Wireless Bridge

  - by Spencer Ruport

  I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

  Read the article

• Show both routers SSID with Wireless bridge [closed]

  - by Valter Henrique

  I have two router 'GVT-1' (the main router) and 'GVT-2' (the second router), this seconds router is used as a repeater only, so I setup a wireless bridge but after I did that it only show 'GVT-2' and if I go closer the 'GVT-1' the signal gets weak cause I'm far from the second router. What I wish is to had the same connection with a wide signal, there's something that I cand do about it ? Thanks.

  Read the article

• How to make sysctl network bridge settings persist after a reboot?

  - by Zack Perry

  I am setting up a notebook for software demo purpose. The machine has 8GB RAM, a Core i7 Intel CPU, a 128GB SSD, and runs Ubuntu 12.04 LTS 64bit. The notebook is used as a KVM host and runs a few KVM guests. All such guests use the virbr0 default bridge. To enable them to communicate with each other using multicast, I added the following to the host's /etc/sysctl.conf, as shown below net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Afterwards, following man sysctl(8), I issued the following: sudo /sbin/sysctl -p /etc/sysctl.conf My understanding is that this should make these settings persist over reboots. I tested it, and was surprised to find out the following: root@sdn1 :/proc/sys/net/bridge# more *tables :::::::::::::: bridge-nf-call-arptables :::::::::::::: 1 :::::::::::::: bridge-nf-call-ip6tables :::::::::::::: 1 :::::::::::::: bridge-nf-call-iptables :::::::::::::: 1 All defaults are coming back! Yes. I can use some kludgy "get arounds" such as putting a /sbin/sysctl -p /etc/sysctl.conf into the host's /etc/rc.local but I would rather "do it right". Did I misunderstand the man page or is there something that I missed? Thanks for any hints. -- Zack

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• Developer Preview available for the Java Access Bridge is now included in Java SE 7 Update 6

  - by Ragini Prasad

  The Java Access Bridge product is now being included with Java SE 7u6. Manual installation of the Java Access Bridge will no longer be required. All Access Bridge files will be automatically installed by the JRE and the JDK.             The Developer Preview for this feature is now available and can be downloaded from http://jdk7.java.net/download.html.            By default, the Java Access Bridge is disabled. In order to use the Java Access Bridge, enable it using the steps mentioned below and test your applications for accessibility.             Enable the Java Access Bridge: Use one of these mechanism:             1. Ease Of Access control panel.     On Windows Vista and later the Java Access Bridge can be enabled     from Ease of Access Center.     Select "Use the computer without a display". In "Other programs     installed" section , select the check box to     "Enable Java Access Bridge" and apply. 2. Or run the following command in the Command Window.     %JRE_HOME%\bin\jabswitch -enable Note: You must restart your Assistive Technology software and Java application after enabling the bridge.             Test the Java Access Bridge: 1. Enable the Java Access Bridge as described above. 2. Run an Assistive Technology that supports the Java Access Bridge. 3. Run a Java application. Ensure that the Assistive Technology  reads    the values of your application. Disable the Java Access Bridge:             Run the following command from the Command Window.     %JRE_HOME%\bin\jabswitch -disable                 Note: The Ease Of Access control panel cannot be used to disable the bridge. You must use jabswitch from the Command window to disable the Java Access Bridge.

  Read the article

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

• Copy all bridge traffic to a specific interface

  - by Azendale

  I have a bridge/switch set up an a machine that has multiple ports. Occasionally, I have a vm running through virtualbox, and I'll have it use a virtual adapter and then I add the adapter to the bridge. I have heard that some switches can copy all the traffic they see to a specific port on the bridge, usually for network monitoring. I would like to be able to run some windows based network tools. I do not want to run Windows on the actual hardware, because it would be lots of work to duplicate my setup in windows, so I was thinking if I can copy all traffic to a port, I can send it to a VM with windows. How can I set this up? I think this might be ebtables area, but I don't know ebtables well enough to know for sure, and it always seems like (from my understanding of ebtables) ebtables does something with the traffic (drop, accept, etc), but never copies it.

  Read the article

• Advantages to Server Scripting languages over Client Side Scripting languages

  There are numerous advantages to server scripting languages over client side scripting languages in regards to creating web sites that are more compelling compared to a standard static site. Server side scripts are executed on a web server during the compilation of data to return to a client. These scripts allow developers to modify the content that is being sent to the user prior to the return of the data to the user as well as store information about the user. In addition, server side scripts allow for a controllable environment in which they can be executed. This cannot be said for client side languages because the developer cannot control the users’ environment compared to a web server. Some users may turn off client scripts, some may be only allow limited access on the system and others may be able to gain full control of the environment.  I have been developing web applications for over 9+ years, and I have used server side languages for most of the applications I have built.  Here is a list of common things I have developed with server side scripts. List of Common Generic Functionality: Send Email FTP Files Security/ Access Control Encryption URL rewriting Data Access Data Creation I/O Access The one important feature server side languages will help me with on my website is Data Access because my component will be backed with a SQL server database. I believe that form validation is one instance where I might see server side and client side scripts used interchangeably because it does not matter how or where the data is validated as long as the data that gets inserted is valid.

  Read the article

• Cracking Websites with Cross Site Scripting

  - by Akemi Iwaya

  You may have heard the term ‘cross site scripting’ before, but what exactly is ‘it’ and why is it dangerous for a website? YouTube channel Computerphile presents a nice primer on the ‘how and why’ of cross site scripting and the dangers it presents in their latest video. Cracking Websites with Cross Site Scripting – Computerphile [YouTube]     

  Read the article

• First 10 programs in a new scripting languge

  - by pro_metedor

  When a peron is learning a new scripting language like: bash python perl pike What kind of simple (yet practical) problem solutions to get through to make say that a person is comprehend with this scripting language enough to approach some complex yet still practical problems encountered in everyday job. In other words, which problems would you give that person to solve to make sure that he/she is familiar with the scripting language.

  Read the article

• Hanging of host network connections when starting KVM guest on bridge

  - by Chris Phillips

  Hi, I've a KVM system upon which I'm running a network bridge directly between all VM's and a bond0 (eth0, eth1) on the host OS. As such, all machines are presented on the same subnet, available outside of the box. The bond is doing mode 1 active / passive, with an arp_ip_target set to the default gateway, which has caused some issues in itself, but I can't see the bond configs mattering here myself. I'm seeing odd things most times when I stop and start a guest on the platform, in that on the host I lose network connectivity (icmp, ssh) for about 30 seconds. I don't lose connectivity on the other already running VM's though... they can always ping the default GW, but the host can't. I say "about 30 seconds" but from some tests it actually seems to be 28 seconds usually (or at least, I lose 28 pings...) and I'm wondering if this somehow relates to the bridge config. I'm not running STP on the bridge at all, and the forwarding delay is set to 1 second, path cost on the bond0 lowered to 10 and port priority of bond0 also lowered to 1. As such I don't think that the bridge should ever be able to think that bond0 is not connected just fine (as continued guest connectivity implies) yet the IP of the host, which is on the bridge device (... could that matter?? ) becomes unreachable. I'm fairly sure it's about the bridged networking, but at the same time as this happens when a VM is started there are clearly loads of other things also happening so maybe I'm way off the mark. Lack of connectivity: # ping 10.20.11.254 PING 10.20.11.254 (10.20.11.254) 56(84) bytes of data. 64 bytes from 10.20.11.254: icmp_seq=1 ttl=255 time=0.921 ms 64 bytes from 10.20.11.254: icmp_seq=2 ttl=255 time=0.541 ms type=1700 audit(1293462808.589:325): dev=vnet6 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.604:326): dev=vnet7 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.618:327): dev=vnet8 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x130079 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0xc1 data 0xffdd694a kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x530079 64 bytes from 10.20.11.254: icmp_seq=30 ttl=255 time=0.514 ms 64 bytes from 10.20.11.254: icmp_seq=31 ttl=255 time=0.551 ms 64 bytes from 10.20.11.254: icmp_seq=32 ttl=255 time=0.437 ms 64 bytes from 10.20.11.254: icmp_seq=33 ttl=255 time=0.392 ms brctl output of relevant bridge: # brctl showstp brdev brdev bridge id 8000.b2e1378d1396 designated root 8000.b2e1378d1396 root port 0 path cost 0 max age 19.99 bridge max age 19.99 hello time 1.99 bridge hello time 1.99 forward delay 0.99 bridge forward delay 0.99 ageing time 299.95 hello timer 0.50 tcn timer 0.00 topology change timer 0.00 gc timer 0.04 flags vnet5 (3) port id 8003 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags vnet0 (2) port id 8002 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags bond0 (1) port id 0001 state forwarding designated root 8000.b2e1378d1396 path cost 10 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 0001 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags I do see the new port listed as learning, but in line with the forward delay, only for 1 or 2 seconds when polling the brctl output on a loop. All pointers, tips or stabs in the dark appreciated.

  Read the article

• Scripting a sophisticated RTS AI with Lua

  - by T. Webster

  I'm planning to develop a somewhat sophisticated RTS AI (eg see BWAPI). have experience programming, but none in game development, so it seems easiest to start by scripting the AI of an existing game I've played, Warhammer 40k: Dawn of War (2004). As far as I can tell, the game AI is scripted with some variant of Lua (by the file extension .ai or .scar). The online documentation is sparse and the community isn't active anymore. I'd like to get some idea of the difficulty of this undertaking. Is it practical with a scripting language like Lua to develop a RTS AI that includes FSMs, decision trees, case-based reasoning, and transposition tables? If someone has any experience scripting Dawn of War, that would also help.

  Read the article

• Xen Bridge only working when IP Assigned

  - by m.sr

  Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

  Read the article

• Importance of scripting engine at Cocos2d Game Engine

  - by Mahbubur R Aaman

  Each Game Engine is different and solves different problems in different ways, so the engine design does vary greatly from engine to engine (even though a lot of principles are shared from engine to engine). Cocos2D is a great product on it’s own, but it doesn’t expose engine functionality to a scripting Language like Lua, JavaScript etc. My Question: How much important to integrate a Scripting Engine at Cocos2d?

  Read the article

• Scripting the Vim editor, Part 5: Event-driven scripting and automation

  <b>IBM Developerworks:</b> "Why repeat yourself? You can configure Vim&#8217;s comprehensive event model to execute time-saving scripts whenever particular editing events&#8212;such as loading a file or switching between editor modes&#8212;occur."

  Read the article

• A good tool for browser automation/client-side Web scripting

  - by hardmath

  I'm interested in adopting a tool/scripting language to automate some daily tasks connected with fighting forum spammers. A brief overview of these tasks: analyze new registrations and posts on a phpBB forum, and delete or deactivate spammers using a website/community that collects such spam reports. Typically such automation is integrated into the phpBB installation itself, which certainly has its advantages. My approach has the advantage of independent operation, etc. One way to think about this is in terms of browser automation. I've used iOpus iMacros for Firefox (the free version) in the past to respond to individual spammers, but current attacks are highly distributed. My "logic" for pigeonholing spammers vs. nonspammers seems beyond the easy reach of the free version of iMacros. From a more technical perspective one can think about dispensing with the browser altogether and programming GET/POST requests directed to my forum and other Web-based resources. I'm familiar with some scripting languages like Ruby and Lua, but I could be persuaded that a compiled application is better suited for these tasks. However in my experience the dynamic flexibility of interpreted environments is very useful in prototyping and debugging the application logic. So I'm leaning in the direction of scripting languages. Among browsers I favor Firefox and Chrome. I use both Windows and Linux platforms, and if the tool can adapt to an Android platform, it would make a neat demonstration of skills, yes? Thanks in advance for your suggestions!

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >