Search Results

Search found 340 results on 14 pages for 'wlan'.

Page 1/14 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Transfer VLAN tagged packets over WLAN?

    - by stefan.at.wpf
    I have the following composition of devices: [selfmade router] - ethernet - [WLAN router 1] ----- wlan ------ [WLAN router 2] WLAN router 2 has 5 ethernet ports, each as an own VLAN, so 5 VLANs. I want to manage the routing and firewalling between those VLANs at selfmade router. What technique would I use to pass the tagged vlan packets from WLAN router 2 to selfmade router? Could I use a bridge from WLAN router 2 to WLAN router 1 which itself has a bridge from WLAN router 1 to selfmade router or do I have a wrong understanding of a bridge? Thanks for any hint on this :-)

    Read the article

  • Bridge virtual machines out WLAN interface

    - by Thomas
    It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

    Read the article

  • Using NPS to restrict access to WLAN

    - by eric.s
    We currently have one WLAN that only domain users can connect to. We will be adding a guest WLAN and would like all non-domain machines to use this, even if a user has a domain account. We have set up NPS and can log in against it, but we can not restrict the connection option to be a domain computer AND a domain account. As a network policy it states that it moves along through each policy until it finds one that it accepts or runs out. For connection request policies Domain Computers is not an option. This is where I thought I may be able to stop it. Has anyone been able to successfully restrict this without manually adding MACs to the WLAN Controller?

    Read the article

  • Bridge virtual machines out WLAN interface

    - by Thomas
    It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

    Read the article

  • Rate of UDP packet loss over WLAN

    - by Martin
    While testing something with TFTP I noticed lots of timeouts (and slow speed as result) when I used my WLAN - and no problems when using a network cable. A quick test program sending/receiving UDP revealed that there are about 3-5% packets lost. While it's obvious that WLAN has to be less reliable than LAN, I have no knowledge what loss rates are considered 'normal' - and when there is a need to further investigate the network infrastructure. Are there 'typical' packet loss rates on WLAN (and other network technologies e.g. PowerLAN, WAN, ...? Thanks

    Read the article

  • Mac WLAN 802.11b+g WPA1 connection issues

    - by Peto
    Hi, I have a Telewell TW-EA510v4 ADSL modem+WLAN router configured as follows: Mode: 802.11b+g Security Mode: WPA1 Pre-shared Key WPA Algorithms: TKIP Connections from only certain MAC addresses have been allowed and the MAC address of my Mac is in that list. The WLAN works just fine with iPhone and an old Acer laptop. It has worked for about two months or so with my MacBook Pro (year and a half or so old model). Ocassionally i've had minor problems with it, which have required either reboot of ADSL modem or reboot of my Mac. However now, for the last week or so I haven't been able to connect to it at all. This is what is what i get in the console when i try to connect: 5.5.2010 20.54.53 airportd[73731] Apple80211Associate() failed -3924 (Invalid PMK) 5.5.2010 20.54.53 Apple80211 framework[584] airportd MIG failed (Associate Event) = -3924 (Invalid PMK) (port = 104599) 5.5.2010 20.54.53 SystemUIServer[584] Error joining WLAN-M: Invalid password (-3924 Invalid master key) The pre-shared key I use is not incorrect. I'm 100% sure of that. The Error Log from the router only says this when I try to connect to it: May 05 21:09:54 home.gateway:i802_1x:none: <my mac address> associated May 05 21:10:00 home.gateway:i802_1x:none: <my mac address> disassociated May 05 21:10:01 home.gateway:i802_1x:none: <my mac address> disassociated Any ideas or tips to troubleshoot this further?

    Read the article

  • ndiswrapper wlan driver installed, but wlan still does not work

    - by mugetsu
    I'm trying to get my Atheros AR1111 EB-WG PCI wireless adapter to work. Right now wifi is not even detected. I'm on ubuntu 12.04 64bit and I managed to find a xp64bit driver. I followed the exact steps here: https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper And where I do ndiswrapper -l I get something like : {name of driver} : driver installed device ({Chipset ID}) present which shows that the driver installed properly However, after I load the new module : sudo modprobe ndiswrapper nothing happens, and iwconfig shows that I still have no wlan. I tried to do dmseg | grep ndiswrapper, but there were no driver loading errors or anything strange. I also have blacklist ath5k, ath8k in /etc/modprobe.d/blacklist.conf What am I doing wrong? What could be causing this?

    Read the article

  • netsh wlan add profile not importing passphrase

    - by sirlancelot
    I exported a wireless network connection profile from a Windows 7 machine correctly connected to a WiFi network with a WPA-TKIP passphrase. The exported xml file shows the correct settings and a keyMaterial node which I can only guess is the encrypted passphrase. When I take the xml to another Windows 7 computer and import it using netsh wlan add profile filename="WiFi.xml", it correctly adds the profile's SSID and encryption type, but a balloon pops up saying that I need to enter the passphrase. Is there a way to import the passphrase along with all other settings or am I missing something about adding profiles? Here is the exported xml with personal information removed: <?xml version="1.0"?> <WLANProfile xmlns="http://www.microsoft.com/networking/WLAN/profile/v1"> <name>[removed]</name> <SSIDConfig> <SSID> <hex>[removed]</hex> <name>[removed]</name> </SSID> <nonBroadcast>false</nonBroadcast> </SSIDConfig> <connectionType>ESS</connectionType> <connectionMode>auto</connectionMode> <autoSwitch>false</autoSwitch> <MSM> <security> <authEncryption> <authentication>WPAPSK</authentication> <encryption>TKIP</encryption> <useOneX>false</useOneX> </authEncryption> <sharedKey> <keyType>passPhrase</keyType> <protected>true</protected> <keyMaterial>[removed]</keyMaterial> </sharedKey> </security> </MSM> </WLANProfile> Any help or advice is appreciated. Thanks.

    Read the article

  • netsh wlan add profile not imported passphrase

    - by sirlancelot
    I exported a wireless network connection profile from a Windows 7 machine correctly connected to a WiFi network with a WPA-TKIP passphrase. The exported xml file shows the correct settings and a keyMaterial node which I can only guess is the encrypted passphrase. When I take the xml to another Windows 7 computer and import it using netsh wlan add profile filename="WiFi.xml", it correctly adds the profile's SSID and encryption type, but a balloon pops up saying that I need to enter the passphrase. Is there a way to import the passphrase along with all other settings?

    Read the article

  • Need instructions how to create wpa_supplicant.conf and add fast_reauth=0 to it // WPA 2 Enterprise & frequent wlan disconnects

    - by nutty about natty
    Like many other natty users on a university / academic network, I'm experiencing annoying frequent disconnects / hangs / delays. See, for instance: https://bugs.launchpad.net/ubuntu/+source/wpasupplicant/+bug/429370 I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: http://w1.fi/gitweb/gitweb.cgi?p=hostap.git;a=blob_plain;f=wpa_supplicant/README [quote] You will need to make a configuration file, e.g., /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. [unquote] Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

    Read the article

  • How to prevent WLAN connection from dropping permanently on a Fritz USB WLAN N stick?

    - by Chris
    I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

    Read the article

  • Installer says I'd need a wireless firmware, but WLAN works without it out of the box

    - by unor
    While installing 12.04.01 (Alternate) on a netbook (Samsung N150Plus), Ubuntu informed me that I'd need the firmware brcm/bcm43xx-0.fw. I skipped this step. If I understand this page correctly, the mentioned firmware is a WLAN driver. However, after the Ubuntu installation was completed, the WLAN worked out of the box. After a few minutes, Ubuntu informed me that there is a firmware update available, which would be the mentioned firmware. Do I need to install this? Is Ubuntu using some kind of "lite" WLAN driver and I might run into problems with certain networks in the future, if I don't use the firmware? Would there be benefits in using the firmware? (maybe longer runtime because of lower consumption?)

    Read the article

  • Wlan connection got lost permanent

    - by chris
    I have a desktop with a fritz usb wlan n tick and tried ubuntu 12.04. installlation is fine and wlan is working, however connection drops permanent. reconnecting manually fixes it but after a few minutes it drops again. it's connected to a vodafone 802 box with wlan n fix set. it seems that it works when i switch off n mode...but i need to test. can someone confirm or is there another solution? i have another machine with 12.04 (hp 625 laptop) running where connection is stable. any help much appreciated. thank chris

    Read the article

  • How to prevent WLAN connection from dropping permanently?

    - by Chris
    I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

    Read the article

  • How do you add a certificate for WLAN in Linux, at the command-line?

    - by Neil
    I'm using Maemo on a Nokia n810 Internet tablet, and when given a list of installed certificates to choose from when connecting to a PEAP wireless network, it's always blank. I've already installed a couple of certificates through the gui on the device, and only the certificate authorities show up. I've confirmed that Maemo's connection software that handles certificates is buggy, in such a way that certificates are never added, or properly added certificates cannot be found. Is there a way to add WLAN certificates at the command-line, and connect to a wireless network at the command-line as well? I used to use iwconfig to connect, but I never used it with PEAP. Note: I have nothing in /etc/ssl/certs

    Read the article

  • How do you add a certificate for WLAN in Linux, at the command-line?

    - by Neil
    I'm using Maemo on a Nokia n810 Internet tablet, and when given a list of installed certificates to choose from when connecting to a PEAP wireless network, it's always blank. I've already installed a couple of certificates through the gui on the device, and only the certificate authorities show up. I've confirmed that Maemo's connection software that handles certificates is buggy, in such a way that certificates are never added, or properly added certificates cannot be found. Is there a way to add WLAN certificates at the command-line, and connect to a wireless network at the command-line as well? I used to use iwconfig to connect, but I never used it with PEAP. Note: I have nothing in /etc/ssl/certs

    Read the article

  • MacMini (running Ubuntu 14.04) loses wlan connection when uploading larger files (several 100 mb) via ownCloud

    - by ManekenT
    I installed Ubuntu 14.04 on an old MacMini with the intention of running it as a homeserver. Additionally I installed ownCloud and tried to sync some files both from a laptop running elementaryOS and a desktop running windows 7. Syncing smaller files workes like a charm (4000 files at <10mb each) but when it comes to bigger files (1 GB ubuntu iso e.g.) the upload failes after 20-100mb. I can't ping the server anymore and the server can't ping me. It still shows up in our router as connected though. Disconnecting and reconnecting the wlan connection fixes the issue until the next attempt at syncing. Edit: I also had to install the wlan driver with this manual: https://help.ubuntu.com/community/MacBookPro8-2#Wireless

    Read the article

  • Manage Your WLAN from the Cloud

    Instead of organizations having to purchase, set up and maintain back-end servers, cloud-based WLAN management services offer hosted access that's cost effective and requires no installation.

    Read the article

  • Getting WLAN on my Laptop to work (Medion MD98300)

    - by Anand Böhmer
    Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

    Read the article

  • Nokia 5800 v50, getting "Invalid server name" with ad-hoc wlan with Windows 7

    - by Krunal
    After upgrading to v50 firmware in my Nokia 5800 xpress music phone. I am not able to connect to ad-hoc wlan network in my laptop(Windows 7 OS). I have a dialup internet connection and created wireless ad-hoc network to access the internet in my phone. But I am getting "invalid server name" in the phone and my wireless network access type in Windows 7 shows "no internet access". I am able to connect to wlan infrastructure network using 5800 in my office. So my phone is working with wlan and I m able to access internet on it. BUT The problem is "dial up with ICS enabled" and "AD-HOC wlan network" in Windows 7. Can anyone give some solution on it. Or can you provide a guide/tutorial to connect 5800 with adhoc network and dialup internet in Windows 7. System: Windows 7 Dial up internet connection with ICS enabled. Ad-Hoc wireless network with WEP Nokia 5800 Xpress Music phone Note: I have read other posts also and tried their solutions but didn't worked for me. the first solution is to bridge the network and access it. but how can I bridge the dialup and wlan netwok? second solution is manually configure IP and DNS addresses in phone. But what should I add as IP and DNS as my dial up and adhoc network have automatic addresses.

    Read the article

  • Wireless hotkey not working on samsung rv 509

    - by Nirmik
    I have a Samsung NP-RV509-A0GIN laptop and LINUX UBUNTU 11.10 installed on it. all the Fn key combinations work except for the Fn+F9 i.e the wireless or the WLAN key. I am not able to switch off my wireless port as the key is not working. I can switch off the bluetooth from the bluetooth menu and disable wireless from the networking menu but this doesnt switch off the port.The indication light for wireless still keeps glowing. I tried many things but it is not working still. Can anyone please help me out with the Fn+F9(WLAN) hotkey problem?

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >