Search Results

Search found 249 results on 10 pages for 'asa'.

Page 1/10 | 1 2 3 4 5 6 7 8 9 10  | Next Page >

• Cisco ASA Act as a Hardware Security Module?

  - by Derek

  Hello, We have a partner that is requiring us to get a HSM for a web application that we host for them. This is something new for us, we've always installed our SSL certificates on our web servers and never needed a hardware device. We currently have 2 Cisco ASA 5510 firewalls in an active/standby configuration. Both ASAs have a ASA-SSM-10 security module installed in them. The web application is a standard HTTPS webpage with no authentication required. I was wondering if we could use our Cisco ASAs to meet this requirement or if we'll have to buy another device. I was doing some searching and read about Cisco's clientless webvpn feature. It sounds like it might work, but I'm not sure. We basically want the ASA to handle the SSL and proxy the connection to our web servers. We do not want to prompt for a username or password to connect or show any portals, just display the web page. If the ASA cannot do this, does any one have any recommendations for network attached hardware security modules? We are using VMware vCenter, so we'd rather have an external device attached to the network, rather than buying HSM cards for every ESXi host. Thanks, Derek

  Read the article

• Cisco ASA not forwarding traffic from one interface to another

  - by Antoine Benkemoun

  Hello ServerFault, I am needing help in the configuration process of my Cisco ASA 5510. I have set up 4 Cisco ASA interconnected together via a big LAN. Each Cisco ASA has 3 or 4 LANs attached to them. The IP routing part is taken care of by OSPF. My problem is on another level. A computer connected to one of the LANs attached to an ASA has no problem communicating with the outside world. The outside world being anything "after" the ASA. My problem is that I am completely unable to have them communicate with another LAN connected to the same ASA. To rephrase this, I am unable to send traffic from one interface of a given ASA to another interface of the same ASA. My configuration is the following : ! hostname Fuji ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 10.0.0.2 255.255.255.0 no shutdown ! interface Ethernet0/1 speed 100 duplex full nameif cs4 no shutdown security-level 100 ip address 10.1.4.1 255.255.255.0 ! interface Ethernet0/2 speed 100 duplex full no shutdown ! interface Ethernet0/2.15 vlan 15 nameif cs5 security-level 100 ip address 10.1.5.1 255.255.255.0 ! interface Ethernet0/2.16 vlan 16 nameif cs6 security-level 100 ip address 10.1.6.1 255.255.255.0 ! interface Management0/0 speed 100 duplex full nameif management security-level 100 ip address 10.6.0.252 255.255.255.0 ! access-list nat_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list acl_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list nat_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list acl_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list nat_cs6 extended permit ip 10.1.6.0 255.255.255.0 any access-list acl_cs6 extended permit ip 10.1.6.0 255.255.255.0 any ! access-list nat_outside extended permit ip any any access-list acl_outside extended permit ip any 10.1.4.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.5.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.6.0 255.255.255.0 ! nat (outside) 0 access-list nat_outside nat (cs4) 0 access-list nat_cs4 nat (cs5) 0 access-list nat_cs5 nat (cs6) 0 access-list nat_cs6 ! static (outside,cs4) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs5) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs6) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 ! static (cs4,outside) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs5) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs6) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 ! static (cs5,outside) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs4) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs6) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 ! static (cs6,outside) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs4) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs5) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 ! access-group acl_outside in interface outside access-group acl_cs4 in interface cs4 access-group acl_cs5 in interface cs5 access-group acl_cs6 in interface cs6 ! router ospf 1 network 10.0.0.0 255.255.255.0 area 1 network 10.1.4.0 255.255.255.0 area 1 network 10.1.5.0 255.255.255.0 area 1 network 10.1.6.0 255.255.255.0 area 1 log-adj-changes ! There is nothing really complicated in this configuration. It just NATs from one interface to another and that's it. I have tried enabling same-security-traffic permit inter-interface but that doesn't help. I therefore must be missing something a little bit more complicated. Does anyone know why I cannot foward traffic from one interface to another ? Thank you in advance for your help, Antoine

  Read the article

• Cisco ASA 5510 Time of Day Based Policing

  - by minamhere

  I have a Cisco ASA 5510 setup at a boarding school. I determined that many (most?) of the students were downloading files, watching movies, etc, during the day and this was causing the academic side of our network to suffer. The students should not even be in their rooms during the day, so I configured the ASA to police their network segment and limit their outbound bandwidth. This resolved all of our academic issues, and everyone was happy. Except the resident students. I have been asked to change/remove the policing policy at the end of the day, to allow the residents access to the unused bandwidth at night. There's no reason to let bandwidth sit unused at night just because it would be abused during the day. Is there a way to setup Time of Day based Policies on the ASA? Ideally I'd like to be able to open up the network at night and all day during weekends. If I can't set Time based policies, is is possible to schedule the ASA to load a set of commands at a specific time? I suppose I could just setup a scheduled task on one of our servers to log in and make the changes with a simple script, but this seems like a hack, and I'm hoping there is a better or more standard way to accomplish this. Thanks. Edit: If there is a totally different solution that would accomplish a similar goal, I'd be interested in that as well. Free/Cheap would be ideal, but if a separate internet connection is my only other option, it might be worth fighting for money for hardware or software to do this better or more efficiently.

  Read the article

• ASA 5510 Need to filter traffic log events to my iPhone

  - by drpcken

  For some reason I cannot update apps or download apps to any ios devices on my network (tried both iphone and ipads). When I'm at home on my own network everything works fine. This started about a week ago. I've configured my iphone with a static IP address and even used 4.2.2.2 as my dns to rule out that the issue is with my DNS Server. I'm looking at the SYSLOG in ASDM (Cisco ASA 5510) but Im not sure it is providing me enough info. It seems to be showing ACL blocks on my public ip address, but not individual client IP's, so I can't see whats going on. How can I setup a way to filter any incoming/outgoing traffic to my iPhone's static IP and try and troubleshoot this?

  Read the article

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

  - by milkandtang

  I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

  Read the article

• Cisco ASA intermittently fails to see traffic

  - by DrStalker

  users | Mikrotik -- Internet | ASA | ServerA and ServerB I'm trying to troubleshoot a problem with a new Cisco ASA 5505. The network design is as above - the Microtik is the existing router, ServerA and ServerB used to plug directly into it. ServerA has IP 10.30.1.10, ServerB has IP 10.30.1.11 The ASA is configured with no NAT, a "allow anything" firewall, and uses the microtik as its default gateway. In effect, it is currently a simple IP router; the firewall and VPN stuff will all come later once the basics are working. Th problem is access to ServerA and ServerB is erratic - sometimes it will work, sometimes it will fail. It can fail for either one of the servers only, or both. When it is working: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show the incoming connections. When it is failing: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show nothing reaching the ASA. This can fail for one server only (e.g.: the Mikrotik is putting out packets to 10.30.1.10 and 10.30.1.11, but the ASA is only seeing packets arrive destined for 10.30.1.11) It can fail for one source only (e.g.: ClientA on the users network can ping 10.30.1.11, but clientB cannot) The problem can also be seen from the mikrotik router itself; sometimes it can ping ServerA and ServerB, sometimes it can only ping one of them What could be causing this? I can't think of any possible cause that is intermittent and could explain why the problem may occur for one destination server and not others. edit: Link to ASA config

  Read the article

• Enable Cisco ASA as an SSH Tunneling

  - by Jim

  I am trying to utilize my Cisco ASA as a SSH Tunnel. I've configured this before when using a Linux server as the SSH target, however I cannot seem to get it to work with the ASA. I have configured and enabled SSH on the Cisco ASA, as well as a username that I can SSH to the console, however the SSH Tunneling feature does not work. For example, on my PC I use Putty with a Local Tunnel defined to a server behind the ASA. I should be able to (if SSH connected to the ASA) be able to access the server. See screenshot of putty. has anyone come across this before? Again this is to use my Cisco ASA as a SSH tunnel, this is not a port forwarding. -Jim

  Read the article

• static routes, cisco ASA, remote locations

  - by Jeff

  192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

  Read the article

• Cisco ASA 5505 allowing inbound ICMPv6

  - by Astron

  I am trying to allow inbound unsolicited ICMPv6 requests from an external link-local address to my outside (external) interfaces link-local address. I can ping (echo-request) the external address and receive a pong (echo-reply) but ICMPv6 messages initiated on the far side are dropped. I am running 9.0(1) in order to use some of the newer features. Does the Cisco ASA not allow unsolicited inbound requests from a link-local address? Should it matter if all ICMPv6 is allowed? Statements being denied: %ASA-3-313008: Denied IPv6-ICMP type=129, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside %ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside %ASA-3-313008: Denied IPv6-ICMP type=131, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside %ASA-3-313008: Denied IPv6-ICMP type=136, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside %ASA-3-313008: Denied IPv6-ICMP type=136, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside %ASA-3-313008: Denied IPv6-ICMP type=136, code=0 from fe80::XXXX:XXXX:XXXX:XXXX on interface outside I created both an inbound ACL and ICMP permit statements: access-list OUTSIDE-IN extended permit icmp6 any any access-list OUTSIDE-IN extended permit icmp6 any any membership-report access-list OUTSIDE-IN extended permit icmp6 any any membership-report 0 access-list OUTSIDE-IN extended permit icmp6 any any echo-reply 0 access-list OUTSIDE-IN extended permit icmp6 any any echo-reply access-list OUTSIDE-IN extended permit icmp6 any interface outside membership-report access-list OUTSIDE-IN extended permit icmp6 any interface outside membership-report 0 access-list OUTSIDE-IN extended permit icmp6 any6 any6 echo-reply access-list OUTSIDE-IN extended permit icmp6 any6 any6 membership-report access-list OUTSIDE-IN extended permit icmp6 any6 any6 echo-reply 0 access-list OUTSIDE-IN extended permit icmp6 any6 any6 membership-report 0 snip access-group OUTSIDE-IN in interface outside ipv6 icmp permit any inside ipv6 icmp permit any membership-report outside ipv6 icmp permit any echo-reply outside ipv6 icmp permit any router-advertisement outside ipv6 icmp permit any neighbor-solicitation outside ipv6 icmp permit any neighbor-advertisement outside ipv6 icmp permit any outside

  Read the article

• Cisco ASA and SixXS IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• Cisco ASA and static IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• Cisco ASA site-to-site vpn not initiating phase 1 (not sending udp 500 packets)

  - by Sean Steadman

  I am hoping someone here can help me with my problem. I am trying to setup an IPSEC site-to-site VPN between two cisco ASA 5520's in GNS3 (both using 8.4.2). I have been unsuccesful in getting the tunnel up and it appears neither ASA is sending packets out,in regards to phase 1 and phase 2 (tested by using wireshark and seeing NO udp 500 packets). Doing show ipsec sa and such shows nothing. CALIFORNIA(config)# show ipsec sa There are no ipsec sas FLA-ASA# show ipsec sa There are no ipsec sas I will attach both configurations in two different pastebin files as to keep this post a bit cleaner. Essentially California side has 172.20.1.0/24 and Florida side has 10.10.10.0/24. California ASA config: http://pastebin.com/v0pngYzF Florida ASA config: http://pastebin.com/E2geybta Please let me know if there is any other vital information that could help. I have gotten IPSEC tunnels to work using openSwan (linux) and cisco routers but cannot for the life of me get ASA IPSEC tunnels to work. The ASDM is out of the question I only use cli. Thanks for any useful help!

  Read the article

• Monitoring Bandwidth Usage (Per Internal IP) - Cisco ASA 5505

  - by Joseph Sturtevant

  I manage a small network with a Cisco ASA 5505 and a shared DSL connection. I would like to be able monitor the bandwidth usage of the various users/devices on my network (by IP). Can I do that using the ASA? Has anyone got this working? What is the best way to do this? Some Ideas I Have Seen Online: SNMP with a tool like Cacti Does this give per IP usage with an ASA or just overall usage? Netflow with a tool like ntop Couldn't get this to work. It seems that the Netflows sent by ASA are not exactly standard. Ntop receives them, but doesn't seem to know what do with them.

  Read the article

• Cisco ASA: Routing packets based on where the connections started from

  - by DrStalker

  We have a Cisco ASA 5505 (version 8.2(2)) with three interfaces: outside: IP address 11.11.11.11, this is the default route inside: IP address 10.1.1.1, this is the local subnet newlink: 22.22.22.22, this is a new internet connection. We need to move VPN users from the 11.11.11.11 address to the 22.22.22.22 address, and we're using SSH on the ASA as to test and sort out the routing. The problem we have is this: If we define a particular IP as being on a static route out the newlink interface then it can SSH to 22.22.22.22 fine. If we do not define a static route then the traffic hits the ASA, but the return traffic does not come back over newlink; presumably it gets sent over the outside interfcae as that is the default route. We can't define a static route for each remote endpoint because there are dialup VPN users, who obviously change IP a lot What we need to do is configure the ASA so if a connection comes in on the newlink interface then the outgoing packets for that go over the newlink interface, not the default route. With iptables this should be do-able by marking the connection and doing mark-routing, but what is the equivalent for a Cisco ASA?

  Read the article

• ASA Slow IPSec Performance with Inconsistent Window Size

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremely poor performance when traffic passes over the IPSec VPN. CPU on the devices is ~13%, Memory at 408 MB, and active VPN sessions 2. The load on both of the the devices is particularly low. Latency between the two sites is ~40ms. Screenshot of wireshark file transfer between the two hosts over the firewall IPSec VPN performing at 10MBPS. Note the changing window size. http://imgur.com/wGTB8Cr Screenshot of wireshark file transfer between the two hosts over the firewall not going over IPSec performing at 55MBPS. Constant window size. http://imgur.com/EU23W1e I'm showing an inconsistent window size when transferring over the IPSec VPN ranging in 46,796 to 65535. When performing at 55+MBPS, the window size is consistently 65,535. Does this show a problem in my configuration of the IPSec VPN in the ASA or a Layer1/2 issue? Using ping xxxxxx -f -l I finally get a non-fragment at 1418 bytes so 1418+28 for IP/ICMP headers = 1446. I know that I have 1500 set on the ASA and Ethernet. I do have "Force Maximum segment size for TCP proxy connection to be" "1380" bytes set under Configuration Advanced TCP Options on the ASA. Using IPERF, I am getting a "TCP Window Full" every few seconds and ~3 MBPS performance. http://imgur.com/elRlMpY Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• ASA 5505 8.4 open ports for subnet

  - by fwrawx

  I have an ASA 5505 running 8.4 with its outside interface plugged into our internal network. I want to open up access to hosts on one of the vlans behind that ASA to hosts on our internal network. I was just starting to grasp NAT on our older PIX but the ASA 8.4 has me confused now. Given a clean ASA with an outside vlan of 10.0.0.1/24 and test vlan of 10.0.1.1/24 what's the basic configuration needed to allow any hosts on the outside network to have access to any of the hosts on the test network?

  Read the article

• configure a Cisco ASA to use MS-CHAP v2 for RADIUS authentication

  - by DrStalker

  Cisco ASA5505 8.2(2) Windows 2003 AD server We want to configure our ASA (10.1.1.1) to authenticate remote VPN users through RADIUS on the Windows AD controller (10.1.1.200) We have the following entry on the ASA: aaa-server SYSCON-RADIUS protocol radius aaa-server SYSCON-RADIUS (inside) host 10.1.1.200 key ***** radius-common-pw ***** When I test a login using the account COMPANY\username I see the users credentials are correct in the security log, but I get the following in the windows system logs: User COMPANY\myusername was denied access. Fully-Qualified-User-Name = company.com/CorpUsers/AU/My Name NAS-IP-Address = 10.1.1.1 NAS-Identifier = <not present> Called-Station-Identifier = <not present> Calling-Station-Identifier = <not present> Client-Friendly-Name = ASA5510 Client-IP-Address = 10.1.1.1 NAS-Port-Type = Virtual NAS-Port = 7 Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = <undetermined> Policy-Name = VPN Authentication Authentication-Type = PAP EAP-Type = <undetermined> Reason-Code = 66 Reason = The user attempted to use an authentication method that is not enabled on the matching remote access policy. My assumption is that the ASA is using PAP authentication, instead of MS-CHAP v2; the credentials are confirmed, the proper Remote Access Policy is being used, but this policy is set to only allow MS-CHAP2. What do we need to do on the ASA to make it us MS-CHAP v2? In the ADSM GUI The "Microsoft CHAP v2 compatible" tickbox is enabled, but I don't know what this corresponds to in the config.

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Route traffic on vpn to another interface on an ASA 5510

  - by Dave

  I have a ASA 5510 that has about 60-70 vpn tunnels. I have four interfaces on the device: 1)External, 2)192.168.1.0, 3)192.168.2.0, 4) 192.168.3.0 A VPN tunnel is configured from the remote site (192.168.200.0) to the 192.168.2.0 subnet on the ASA. I have remote applications I would like the users at the remote site to be able to access which are hosted on the 192.168.3.0 subnet. I can route traffic between the subnets that are located on the ASA. Any way I can route traffic from the remote site to the 192.168.3.0?

  Read the article

• Monitoring ASA packet loss via SNMP

  - by dunxd

  I want to monitor packet loss on my ASA 5505 VPN endpoints using SNMP. This is so I can graph the rates in Cacti and/or get alerts in Nagios. However, I am not sure what SNMP values I should use to measure packet loss. In the ASA I can run sh interface Internet stats to show traffic statistics for the interface connected to the Internet. This shows 1 minute and 5 minute drop rates. Are these measures an indicator of packet loss? Are there SNMP values I can access that correspond to those values? Should I be looking at different values? Is the ASA even able to measure packet loss?

  Read the article

• Firewalling a Cisco ASA Split tunnel

  - by dunxd

  I have a Cisco ASA 5510 at head office, and Cisco ASA 5505 in remote offices. The remote offices are connected over a split tunnelled VPN - the ASA 5505s use "Easy VPN" Client type VPN in Network Extension Mode (NEM). I'd like to set firewall rules for the non-tunnelled traffic only. Traffic over the VPN to head office should not have any firewall rules applied. I might want to apply different firewall rules to different remote offices. All the documentation I have been able to find assumes the Client VPN is a software endpoint, and all the configuration is done at the 5510. When using a Cisco 5505 as the VPN client, is it possible to configure any firewalling at the Client end, or does it all have to come from the 5510? Are there any other issues to look out for when split-tunnelling a VPN by this method?

  Read the article

• Cisco ASA - Unable to create "range" type of network object on 8.2

  - by j2k4j

  I'm wanting to block a range of ip addresses on my Cisco ASA 5520 (8.2) using ASDM 6.4. In the help files/cisco documentation, it says, just create a network object with a "range" type, and use that in a blocking access rule... When I'm accessing the ASA (8.2) with ASDM 6.4, I go to configfirewallobjectnetwork objects & groups, then click "add" to add the IP range as a "network object", I get the following 4 fields to fill out: Name: IP address: Netmask: Description: That's all... In the context-sensitive help files, it says that there should be a Type drop-down to select, with "range" being one of the options, but there is no "Type" drop-down list... If I try to create a "network object group" instead of just "network object", then I get a "Type" drop down list, but it only contains two options: network & host (No "Range" option here either) Can someone help me figure out how to block a range of IP's, using the current 8.2 version on the ASA? Thanks for any pointers or tips!

  Read the article

• Cisco ASA - NAT'ing VPN traffic

  - by DrStalker

  I have an IPsec VPN setup like this: [Remote users]-[Remote ASA] <-VPN-> [My ASA]-[Subnet A]-[Router 2]-[Subnet B] The VPN is set to handle traffic between [remote users] and [Subnet A]; it does not include [Subnet B]. Pretend the firewall rules for all routers are to permit everything. Now I want to redirect traffic that comes over the VPN to a specific IP on [subnet A] (192.168.1.102) to an IP on [Subnet B] (10.1.1.133) If I add a rule on [My ASA] to NAT traffic to original IP 192.168.1.102 to new IP 10.1.1.133, 1) Will this affect the connections coming in over the VPN? (ie: the VPN packets are unencrypted and then NAT is applied) 2) Will this work when the post-NAT target is on Subnet-B, which is not part of the VPN traffic selection?

  Read the article

• Outbound Traffic Logging on ASA 5520 possible?

  - by j2k4j

  Taking a look at the ASDM (6.4) for my ASA 5520, I get a nice summary of the traffic status, with items like "interface traffic usage", and "connections per second". This works well, but only shows the data for the last 5-6 minutes or so. Recently, I've been asked whether it's possible to pull up this same type of traffic data for a particular time in the past. (Such as: Find the traffic usage for a 3 minute period from date xx:xx:xx @ time xx:xx:xx) I've noticed that my ASA 5520 is logging the warning, errors, etc that it is processing. But traffic data is not logged (yet) according to my search through the ASA. Is logging the traffic data amounts (as wondered above) actually a possibility? Is there any way to find out the past data for traffic and such values? Thanks!

  Read the article

1 2 3 4 5 6 7 8 9 10  | Next Page >