Search Results

Search found 249 results on 10 pages for 'asa'.

Page 2/10 | < Previous Page | 1 2 3 4 5 6 7 8 9 10  | Next Page >

• Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

  - by franklundy

  Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

  Read the article

• How do you configuring vlans/trunk on a Cicso ASA 5510

  - by Sam Sanders

  I have a Cicso ASA 5510 that I want to connect to 2 Dell PowerConnect 5500 linked in a Switch Stack. I want to connect a trunking line to each switch so if one switch dies the other works. The problem is I can't seem to do anything thing with vlans on the 5510 using the "Cisco ASDM 6.4 for ASA" . Do I need to use CLI for this, or is it just not possible? I'm new at networking so any advice would be helpful.

  Read the article

• ASA 5505 BGP not supported?

  - by sorrrydoctorforlove

  Hey, I need to configure BGP on an ASA 5505, according to certain sources it isn't supported, yet I can find resources on the internet giving information on how to configure BGP. I'd really like an expert to answer some queries for me. Can you configure BGP on the ASA 5505? 1b. if you can't, what can you use in its place?

  Read the article

• DynDNS updating IP address via Cisco ASA 5505

  - by yonatan

  I'm setting up an ASA 5505 where the ISP provides a dynamic IP address (rarely changes.) I would like to start using some of the services provided by DynDNS such as Custom DNS. I've come across some information regarding Cisco Routers and DynDNS, but nothing definitive on the ASA platform. My question is whether I can configure the ASA5505 to update the IP address rather than install the DynDNS Updater software on a machine running on the LAN? Thanks

  Read the article

• LACP : Cisco ASA 5515 & Switch ProCurve 2920

  - by user979276

  I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

  Read the article

• Why do I start at privilege level 1 when logging into a Cisco ASA 5510?

  - by Alain O'Dea

  I have created a test user that is set to privilege 15 in the config: username test password **************** encrypted privilege 15 When I log in to the ASA 5510 I am in privilege 1 according to sh curpriv: login as: test [email protected]'s password: Type help or '?' for a list of available commands. asa> sh curpriv Username : test Current privilege level : 1 Current Mode/s : P_UNPR Attempting enable fails even though I know I have the correct enable password: asa> en Password: ************************* Password: ************************* Password: ************************* Access denied. Logging in from unprivileged puts me on privilege 15 and I can do as a please: asa> login Username : test Pasword: ************************* asa> sh curpriv Current privilege level : 15 Current Mode/s : P_PRIV asa> The only thing I can track this to is a configuration change I made where I removed a VPN user we no longer needed. Why do I start at privilege level 1 when logging into a Cisco ASA 5510?

  Read the article

• VPN Trunk Between Cisco ASA 5520 and DrayTek Vigor 2930

  - by David Heggie

  I'm a bit of a VPN newbie, so please go easy on me ... I'm trying to use the VPN trunking capabilities of the DrayTek Vigor 2930 firewall to bond two IPSec VPN connections to a Cisco ASA 5520 device and I'm getting myself tied in knots and hope someone here with more knowledge / experience can help. I have a remote site with two ADSL connections and the DrayTek box. The main office site has the Cisco ASA device. I am able to setup a single IPSec connection between the two sites on either of the ADSL connections' public IP addresses, but as soon as I try to use the VPN bonding, nothing works. The VPN tunnels are both still up, but the traffic is getting lost somewhere. I suspect it's due to the ASA not knowing how to route the traffic back over the VPN - one minute, traffic from my remote office's network is coming from public ip address #1, the next it's coming from public address #2 and it doesn't know what to do. Well, that's my newbie impression of what's going wrong, but I don't really know: If this is really what's happening If what I'm trying to do (bond two VPN connections from a single remote network to improve the bandwidth / resiliency) is possible with the kit I've got Could anyone help?

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

• Cisco ASA 8.2 ACL For NAT

  - by javano

  Sadly I have gone back in time to ASA 8.2(5)33 which I am not so familiar with. I have configured NAT between two interfaces but traffic isn't passing becasue I can't get the ACL to work; (The full config which isn't very big is here but to keep this post tidy I have just pasted the important parts below); interface Ethernet0/0 switchport access vlan 108 ! interface Ethernet0/6 switchport access vlan 104 ! interface Ethernet0/7 switchport access vlan 105 ! interface Vlan104 description BUILDING2 nameif BUILDING2 security-level 0 ip address 10.104.0.1 255.255.255.0 ! interface Vlan105 description BUILDING1 nameif BUILDING1 security-level 0 ip address 10.105.0.1 255.255.255.0 ! interface Vlan108 description Main LAN VLAN nameif lan security-level 0 ip address 172.22.0.215 255.255.255.0 ! object-group network obj_net_Remote_Hosts network-object host 111.111.111.3 network-object host 111.111.111.65 object-group network obj_host_pc1_eth1 network-object host 10.104.0.111 object-group network obj_host_pc2_eth1 network-object host 10.104.0.112 object-group network obj_host_pc3_eth1 network-object host 10.104.0.106 object-group network obj_host_pc4_eth1 network-object host 10.104.0.107 object-group network obj_net_PCs description IPs of PCs group-object obj_host_pc1_eth1 group-object obj_host_pc2_eth1 group-object obj_host_pc3_eth1 group-object obj_host_pc4_eth1 access-list acl_NAT_pc1_91 extended permit tcp host 10.104.0.111 host 111.111.111.3 eq 8101 access-list acl_Permit_PCs extended permit tcp object-group obj_net_PCs object-group obj_net_Remote_Hosts eq 8101 ! global (BUILDING1) 11 111.111.222.91 netmask 255.255.255.255 nat (BUILDING2) 11 access-list acl_NAT_pc1_91 access-group acl_Permit_PCs in interface BUILDING2 route BUILDING1 111.111.111.3 255.255.255.255 10.105.0.2 1 route BUILDING1 111.111.111.65 255.255.255.255 10.105.0.2 1 When I try and connect from PC1 to ip 111.111.111.3 I see the following error logged on the ASA console; %ASA-2-106001: Inbound TCP connection denied from 10.104.0.111/38495 to 111.111.111.3/8101 flags SYN on interface blades What the duce!

  Read the article

• Shrinking TCP Window Size to 0 on Cisco ASA

  - by Brent

  Having an issue with any large file transfer that crosses our Cisco ASA unit come to an eventual pause. Setup Test1: Server A, FileZilla Client <- 1GBPS - Cisco ASA <- 1 GBPS - Server B, FileZilla Server TCP Window size on large transfers will drop to 0 after around 30 seconds of a large file transfer. RDP session then becomes unresponsive for a minute or two and then is sporadic. After a minute or two, the FTP transfer resumes, but at 1-2 MB/s. When the FTP transfer is over, the responsiveness of the RDP session returns to normal. Test2: Server C in same network as Server B, FileZilla Client <- local network - Server B, FileZilla Server File will transfer at 30+ MB/s. Details ASA: 5520 running 8.3(1) with ASDM 6.3(1) Windows: Server 2003 R2 SP2 with latest patches Server: VMs running on HP C3000 blade chasis FileZilla: 3.3.5.1, latest stable build Transfer: 20 GB SQL .BAK file Protocol: Active FTP over tcp/20, tcp/21 Switches: Cisco Small Business 2048 Gigabit running latest 2.0.0.8 VMware: 4.1 HP: Flex-10 3.15, latest version Notes All servers are VMs. Thoughts Pretty sure the ASA is at fault since a transfer between VMs on the same network will not show a shrinking Window size. Our ASA is pretty vanilla. No major changes made to any of the settings. It has a bunch of NAT and ACLs. Wireshark Sample No. Time Source Destination Protocol Info 234905 73.916986 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131981791 Win=65535 Len=0 234906 73.917220 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234907 73.917224 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234908 73.917231 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131984551 Win=64155 Len=0 234909 73.917463 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234910 73.917467 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234911 73.917469 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234912 73.917476 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131988691 Win=60015 Len=0 234913 73.917706 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234914 73.917710 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234915 73.917715 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131991451 Win=57255 Len=0 234916 73.917949 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234917 73.917953 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234918 73.917958 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131994211 Win=54495 Len=0 234919 73.918193 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234920 73.918197 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234921 73.918202 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131996971 Win=51735 Len=0 234922 73.918435 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234923 73.918440 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234924 73.918445 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131999731 Win=48975 Len=0 234925 73.918679 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234926 73.918684 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234927 73.918689 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132002491 Win=46215 Len=0 234928 73.918922 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234929 73.918927 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234930 73.918932 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132005251 Win=43455 Len=0 234931 73.919165 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234932 73.919169 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234933 73.919174 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132008011 Win=40695 Len=0 234934 73.919408 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234935 73.919413 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234936 73.919418 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132010771 Win=37935 Len=0 234937 73.919652 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234938 73.919656 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234939 73.919661 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132013531 Win=35175 Len=0 234940 73.919895 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234941 73.919899 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234942 73.919904 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132016291 Win=32415 Len=0 234943 73.920138 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234944 73.920142 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234945 73.920147 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132019051 Win=29655 Len=0 234946 73.920381 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234947 73.920386 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234948 73.920391 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132021811 Win=26895 Len=0 234949 73.920625 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234950 73.920629 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234951 73.920632 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234952 73.920638 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132025951 Win=22755 Len=0 234953 73.920868 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234954 73.920871 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234955 73.920876 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132028711 Win=19995 Len=0 234956 73.921111 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234957 73.921115 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234958 73.921120 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132031471 Win=17235 Len=0 234959 73.921356 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234960 73.921362 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234961 73.921370 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132034231 Win=14475 Len=0 234962 73.921598 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234963 73.921606 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234964 73.921613 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132036991 Win=11715 Len=0 234965 73.921841 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234966 73.921848 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234967 73.921855 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132039751 Win=8955 Len=0 234968 73.922085 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234969 73.922092 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234970 73.922099 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132042511 Win=6195 Len=0 234971 73.922328 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234972 73.922335 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234973 73.922342 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132045271 Win=3435 Len=0 234974 73.922571 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234975 73.922579 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234976 73.922586 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132048031 Win=675 Len=0 234981 75.866453 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 675 bytes 234985 76.020168 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0 234989 76.771633 2.2.2.2 1.1.1.1 TCP [TCP ZeroWindowProbe] ivecon-port ftp-data [ACK] Seq=132048706 Ack=1 Win=65535 Len=1 234990 76.771648 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0 234997 78.279701 2.2.2.2 1.1.1.1 TCP [TCP ZeroWindowProbe] ivecon-port ftp-data [ACK] Seq=132048706 Ack=1 Win=65535 Len=1 234998 78.279714 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0

  Read the article

• Shrinking Windows Size to 0 on Cisco ASA

  - by Brent

  Having an issue with any large file transfer that crosses our Cisco ASA unit come to an eventual pause. Setup Test1: Server A, FileZilla Client <- 1GBPS - Cisco ASA <- 1 GBPS - Server B, FileZilla Server TCP Window size on large transfers will drop to 0 after around 30 seconds of a large file transfer. RDP session then becomes unresponsive for a minute or two and then is sporadic. After a minute or two, the FTP transfer resumes, but at 1-2 MB/s. When the FTP transfer is over, the responsiveness of the RDP session returns to normal. Test2: Server C in same network as Server B, FileZilla Client <- local network - Server B, FileZilla Server File will transfer at 30+ MB/s. Details ASA: 5520 running 8.3(1) with ASDM 6.3(1) Windows: Server 2003 R2 SP2 with latest patches Server: VMs running on HP C3000 blade chasis FileZilla: 3.3.5.1, latest stable build Transfer: 20 GB SQL .BAK file Protocol: Active FTP over tcp/20, tcp/21 Switches: Cisco Small Business 2048 Gigabit running latest 2.0.0.8 VMware: 4.1 HP: Flex-10 3.15, latest version Notes All servers are VMs. Thoughts Pretty sure the ASA is at fault since a transfer between VMs on the same network will not show a shrinking Window size. Our ASA is pretty vanilla. No major changes made to any of the settings. It has a bunch of NAT and ACLs. Wireshark Sample No. Time Source Destination Protocol Info 234905 73.916986 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131981791 Win=65535 Len=0 234906 73.917220 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234907 73.917224 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234908 73.917231 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131984551 Win=64155 Len=0 234909 73.917463 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234910 73.917467 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234911 73.917469 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234912 73.917476 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131988691 Win=60015 Len=0 234913 73.917706 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234914 73.917710 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234915 73.917715 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131991451 Win=57255 Len=0 234916 73.917949 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234917 73.917953 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234918 73.917958 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131994211 Win=54495 Len=0 234919 73.918193 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234920 73.918197 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234921 73.918202 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131996971 Win=51735 Len=0 234922 73.918435 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234923 73.918440 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234924 73.918445 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=131999731 Win=48975 Len=0 234925 73.918679 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234926 73.918684 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234927 73.918689 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132002491 Win=46215 Len=0 234928 73.918922 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234929 73.918927 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234930 73.918932 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132005251 Win=43455 Len=0 234931 73.919165 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234932 73.919169 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234933 73.919174 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132008011 Win=40695 Len=0 234934 73.919408 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234935 73.919413 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234936 73.919418 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132010771 Win=37935 Len=0 234937 73.919652 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234938 73.919656 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234939 73.919661 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132013531 Win=35175 Len=0 234940 73.919895 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234941 73.919899 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234942 73.919904 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132016291 Win=32415 Len=0 234943 73.920138 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234944 73.920142 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234945 73.920147 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132019051 Win=29655 Len=0 234946 73.920381 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234947 73.920386 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234948 73.920391 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132021811 Win=26895 Len=0 234949 73.920625 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234950 73.920629 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234951 73.920632 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234952 73.920638 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132025951 Win=22755 Len=0 234953 73.920868 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234954 73.920871 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234955 73.920876 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132028711 Win=19995 Len=0 234956 73.921111 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234957 73.921115 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234958 73.921120 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132031471 Win=17235 Len=0 234959 73.921356 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234960 73.921362 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234961 73.921370 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132034231 Win=14475 Len=0 234962 73.921598 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234963 73.921606 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234964 73.921613 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132036991 Win=11715 Len=0 234965 73.921841 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234966 73.921848 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234967 73.921855 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132039751 Win=8955 Len=0 234968 73.922085 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234969 73.922092 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234970 73.922099 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132042511 Win=6195 Len=0 234971 73.922328 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234972 73.922335 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234973 73.922342 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132045271 Win=3435 Len=0 234974 73.922571 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234975 73.922579 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 1380 bytes 234976 73.922586 1.1.1.1 2.2.2.2 TCP ftp-data ivecon-port [ACK] Seq=1 Ack=132048031 Win=675 Len=0 234981 75.866453 2.2.2.2 1.1.1.1 FTP-DATA FTP Data: 675 bytes 234985 76.020168 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0 234989 76.771633 2.2.2.2 1.1.1.1 TCP [TCP ZeroWindowProbe] ivecon-port ftp-data [ACK] Seq=132048706 Ack=1 Win=65535 Len=1 234990 76.771648 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0 234997 78.279701 2.2.2.2 1.1.1.1 TCP [TCP ZeroWindowProbe] ivecon-port ftp-data [ACK] Seq=132048706 Ack=1 Win=65535 Len=1 234998 78.279714 1.1.1.1 2.2.2.2 TCP [TCP ZeroWindowProbeAck] [TCP ZeroWindow] ftp-data ivecon-port [ACK] Seq=1 Ack=132048706 Win=0 Len=0

  Read the article

• Cisco VPN Client Behind ASA 5505

  - by fdf33

  I'm trying to get connected to another ASA via Cisco VPN Client. I am behind an ASA 5505 myself and I am tryihng to VPN to a 5510. I get the message: Secure VPN Connection terminated locally by the Client. Reason 412: The remote peer is no longer responding. I can connect to the other ASA if I use a normal cheap Linksys. Here's the version of my ASA: Result of the command: "sh ver" Cisco Adaptive Security Appliance Software Version 8.4(1) Any help would be great. Thanks running-config : Saved : Written by enable_15 at 23:12:32.378 UTC Fri Jul 1 2011 ! ASA Version 8.4(1) ! hostname aaaasa domain-name aaa.local enable password xxxxxxxxxxxxxxx encrypted passwd xxxxxxxxxxxxxxxxxxxx encrypted names ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address xxx.xxx.xxx.xxx 255.255.254.0 ! interface Vlan5 no nameif security-level 50 ip address 172.16.0.254 255.255.255.0 ! interface Vlan500 no nameif security-level 100 ip address 10.10.10.1 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! boot system disk0:/asa841-k8.bin ftp mode passive dns domain-lookup inside dns domain-lookup outside dns server-group DefaultDNS name-server 4.2.2.2 domain-name aaa.local same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network A_93.97.168.1 host 93.97.168.1 object network rdp host 192.168.1.2 object network NETWORK_OBJ_192.168.1.0_24 subnet 192.168.1.0 255.255.255.0 access-list 101 extended permit tcp any host 192.168.1.2 eq 3389 access-list 101 extended permit icmp any any echo-reply access-list 101 extended permit icmp any any source-quench access-list 101 extended permit icmp any any time-exceeded access-list 101 extended permit icmp any any unreachable access-list 102 extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1492 ip local pool VPNPool 192.168.2.200-192.168.2.210 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-641.bin no asdm history enable arp timeout 14400 ! object network rdp nat (inside,outside) static interface service tcp 3389 3389 ! nat (inside,outside) after-auto source dynamic any interface access-group 101 in interface outside access-group 102 out interface outside ! router ospf 1 network 192.168.1.0 255.255.255.0 area 0 log-adj-changes ! route outside 0.0.0.0 0.0.0.0 93.97.168.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=ciscoasa proxy-ldc-issuer crl configure crypto ca certificate chain ASDM_TrustPoint0 certificate 8877d64d 30820248 308201b1 a0030201 02020488 77d64d30 0d06092a 864886f7 0d010105 05003036 3111300f 06035504 03130863 6973636f 61736131 21301f06 092a8648 86f70d01 09021612 63697363 6f617361 2e6e6a64 2e6c6f63 616c301e 170d3131 30353231 30383533 34325a17 0d323130 35313830 38353334 325a3036 3111300f 06035504 03130863 6973636f 61736131 21301f06 092a8648 86f70d01 09021612 63697363 6f617361 2e6e6a64 2e6c6f63 616c3081 9f300d06 092a8648 86f70d01 01010500 03818d00 30818902 818100ea 1aa95141 480e616c efee6816 a96d6511 313b6776 cd3dd57b cd84b4d2 5e108aee 7c980086 4d92e2eb b6c7bf66 4585af0a ccbf153a db9270be c6f5c67b db9dd8d1 2f78d033 3348b056 df4be0da 70e08953 53adf294 9db6c020 597d250f bf448b43 b90179c8 ff0b15d8 744632d9 31c1945f 0b11e258 b4c1d224 692efff4 7b2f5102 03010001 a3633061 300f0603 551d1301 01ff0405 30030101 ff300e06 03551d0f 0101ff04 04030201 86301f06 03551d23 04183016 8014493c 19db183a ab1af9e9 b1e44ad4 2a408b3c 89d1301d 0603551d 0e041604 14493c19 db183aab 1af9e9b1 e44ad42a 408b3c89 d1300d06 092a8648 86f70d01 01050500 03818100 1dd1760a fdd15941 4803fb9a cd6f44a7 2e275854 a1c0fbe1 d19f2cc9 182d43ef a547f854 8df96d15 3ea79c62 cf3fcb1c 5820360b c607dbfc 4de8bb16 19f727e9 b928a085 665816d8 138e4a35 ed610950 7910dd4a 0b1a9dd9 0e26f1c8 b78bc0cc cbf19eb2 4c4c3931 45199ea5 249e3266 661e44fd 7a00d376 dcfc6e4e d43f10b8 quit crypto isakmp nat-traversal 30 crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.1.0 255.255.255.0 inside ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.5-192.168.1.36 inside dhcpd dns 4.2.2.2 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host number-of-rate 3 threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server 82.219.4.31 source outside prefer ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside anyconnect image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 anyconnect profiles AnyConnectVPN_client_profile disk0:/AnyConnectVPN_client_profile.xml anyconnect profiles SSLAnyConnectVPN_client_profile disk0:/SSLAnyConnectVPN_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_AnyConnectVPN internal group-policy GroupPolicy_AnyConnectVPN attributes wins-server none dns-server value 4.2.2.2 vpn-tunnel-protocol ikev2 ssl-client ssl-clientless default-domain value aaa.local webvpn url-list none anyconnect profiles value AnyConnectVPN_client_profile type user group-policy GroupPolicy_SSLAnyConnectVPN internal group-policy GroupPolicy_SSLAnyConnectVPN attributes wins-server none dns-server value 4.2.2.2 vpn-tunnel-protocol ikev2 ssl-client default-domain value aaa.local webvpn anyconnect profiles value SSLAnyConnectVPN_client_profile type user username testuser password xxxxxxxxxxxxxxxxx encrypted privilege 0 username testuser attributes vpn-group-policy GroupPolicy_AnyConnectVPN tunnel-group SSLPOL type remote-access tunnel-group SSLPOL general-attributes default-group-policy GroupPolicy_AnyConnectVPN tunnel-group SSLAnyConnectVPN type remote-access tunnel-group SSLAnyConnectVPN general-attributes address-pool VPNPool default-group-policy GroupPolicy_SSLAnyConnectVPN tunnel-group SSLAnyConnectVPN webvpn-attributes group-alias SSLAnyConnectVPN enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect sip inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect xdmcp ! service-policy global_policy global prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:94a65341aa27d3929d5e92a32ba22120 : end

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• IPSEC site-to-site Openswan to Cisco ASA

  - by Jim

  I recieved a list of commands that were run on the right side of the VPN tunnel which is where the Cisco ASA resides. On my side, I have a linux based firewall running debian with openswan installed. I am having an issue with getting to Phase 2 of the VPN negotiation. Here is the Cisco Information I was sent: {my_public_ip} = left side of connection tunnel-group {my_public_ip} type ipsec-l2l tunnel-group {my_public_ip} ipsec-attributes pre-shared-key fakefake crypto map vpn1 1 match add customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside static (outside,inside) 10.2.1.200 {my_public_ip} netmask 255.255.255.255 crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map vpn1 1 match address customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 Myside ipsec.conf config setup klipsdebug=none plutodebug=none protostack=netkey #nat_traversal=yes conn cisco #name of VPN connection type=tunnel authby=secret #left side (myside) left={myPublicIP} leftsubnet=172.16.250.0/24 #net subnet on left sdie to assign to right side leftnexthop=%defaultroute #right security gateway (ASA side) right={CiscoASA_publicIP} #cisco ASA rightsubnet=10.2.1.0/24 rightnexthop=%defaultroute #crypo stuff keyexchange=ike ikelifetime=86400s auth=esp pfs=no compress=no auto=start ipsec.secrets file {CiscoASA_publicIP} {myPublicIP}: PSK "fakefake" When I start ipsec from the left side/my side I don't recieve any errors, however when I run the ipsec auto --status command: 000 "cisco": 172.16.250.0/24==={left_public_ip}<{left_public_ip}>[+S=C]---{left_public_ip_gateway}...{left_public_ip_gateway}--{right_public_ip}<{right_public_ip}>[+S=C]===10.2.1.0/24; prospective erouted; eroute owner: #0 000 "cisco": myip=unset; hisip=unset; 000 "cisco": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cisco": policy: PSK+ENCRYPT+TUNNEL+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,24; interface: eth0; 000 "cisco": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 000 #2: "cisco":500 STATE_MAIN_I1 (sent MI1, expecting MR1); EVENT_RETRANSMIT in 10s; nodpd; idle; import:admin initiate 000 #2: pending Phase 2 for "cisco" replacing #0 Now I'm new to setting up an site-to-site IPSEC tunnel so the status informatino I am unsure what it means. All I know is it sits at this "pending Phase 2" and I can't ping the other side, Another question I have is, if I do a route -n, should I see anything relating to this connection? Also, I read a few artilcle where configs contained the interface="ipsec0=eth0", is this an interface that I have to create on the linux debian firewall on my side? Appreciate your time to look at this.

  Read the article

• Exposing Exchange 2010 OWA via Cisco ASA 5520

  - by Gir

  Has anyone experience with exposing the web access (OWA) of an Exchange 2010 server through a Cisco ASA (my goal is to something like a DMZ)? If so could you give me some advice? I know that Exchange doesn't support DMZ and that MS recommends using TMG. Still, I'd like to know if someone has managed this (I've tried and wasn't very successsful so far). Or would it be better to ditch (read: sell) the ASA and use a TMG server instead? We're completely on Windows Server 2008 R2 and some remaining 2003 server running mostly as file servers. We don't use the VPN features much at the moment but plan on doing that in the future, but OWA should be there if VPN is not possible from outside. Thank you very much!

  Read the article

• Cisco ASA - VPN and Hairpinning....

  - by Nordberg

  Hi, We have 2 sites that will be linked by a IPSEC VPN between 2 Cisco ASAs: Site 1 8Mb ADSL Connection Cisco ASA 505 Site 2 2Mb SDSL Connection Cisco ASA 505 Basically, both sites need access to a service at the end of another IPSEC VPN, Site 3, which I plan to terminate at Site 2. This is due to the way the service is sold - it's billed per gateway. So if both Site 1 and Site 2 had their own VPN connection to Site 3, it would cost us twice as much... Anyway, my idea is to have all traffic from Site 1 destined for Site 3 to go via the VPN between Site 1 and Site 2. The end result being all traffic that hits Site 3 has come via Site 2. I understand this is known as hairpinning but I'm struggling to find a great deal of information on how this is setup. So, firstly, can anyone confirm that what I'm trying to achieve is possible and, secondly, can anyone point me in the direction of an example of such a configuration? Many Thanks.

  Read the article

• Cisco ASA 5505 and slow download speeds for Apple devices

  - by James

  For traffic routing through my ASA 5505, downloads for all Apple devices, including AppleTV iPad gen 1 IMac MacBook Pro are very slow. speedof.me show less than 1 Mbps download (where I should have 20 Mbps +), yet for any Windows-based device, the download speeds are in excess of 20 Mbps. The Windows device, including the iMac and MacBook Pro machines, are connected via ethernet cable. Why are Apple devices experiencing such pain? Is it an ASA setting, or something else? Thanks.

  Read the article

• Is span monitoring on Cisco ASA 5520 possible?

  - by Brent

  From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• MAC to IP binding in ASA 5510 / SG 300-52

  - by Sampsa

  I am trying to configure a Cisco ASA 5510 to assign specific IP-addresses to specific MACs. Firmware on my ASA is 8.2(5). I have used this feature in our previous device (Cisco SA-520W). I have also read that this feature is (not yet) implemented. How do I work around this problem, if not by direct assignment? Do I need to specify fixed IP's on concerned devices themselves? I also have a SG 300-52 switch for our LAN. We cannot specify IP-addresses to ports, because we have further switches down the line. Thank you for your help!

  Read the article

• Taking stock of an existing ASA Firewall

  - by Nate

  Imagine you are given an existing network using an ASA firewall. The network works, but you aren't sure of anything else. The firewall may be completely improperly configured, with "outside" actually being inside and "inside" actually being outside, for all you know. My question is this: what are the commands to take stock of an existing ASA firewall setup? With only CLI access, how do I figure out: What interfaces are available The names of the interfaces The security levels attached to the interfaces The access-lists attached to the interfaces, including rules and directions I know how to set these things (interface, nameif, security-level, and access-list/access-group), but I don't know how to figure them out given an existing system. On a related note, is there anything else that I should worry about checking to make sure that the network isn't wide open? Thanks!

  Read the article

• ASA Slow IPSec Performance

  - by Brent

  I have a IPSec link between two sites over ASA 5520s running 8.4(3) and I am getting extremly poor performance when traffic passes over the VPN. CPU on the device is 13%, Memory at 408 MB, and active VPN sessions 2 so the load on the device is particularly low. Screenshot of wireshark file transfer between the two hosts over the VPN: The large amount of Header checksum failures is alarming, but I am not sure what to check now. I perf is showing around 4-5 Mbit/sec with differing TCP window sizes. Show Run on the ASA http://pastebin.com/uKM4Jh76 Show cry accelerator stats http://pastebin.com/xQahnqK3

  Read the article

• cisco asa query dns external

  - by Alpacino

  my lab network asa firewall below 10.10.10.20 -- ASA --- 192.168.1.10 -- website external my client 10.10.10.20 want to access website external and i create nat nat (inside,outside) static 192.168.1.10 and access list access-list outside-acl extended permit tcp any host 10.10.10.20 eq www access-list outside-acl extended permit tcp any host 10.10.10.20 eq domain access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq www access-list inside-acl extended permit tcp 10.10.10.0 255.255.255.0 any eq domain access-group outside-acl in interface outside access-group inside-acl in interface inside when i access to website with domain name it can't access but i access website with ip address it work please help me to solve problem thank you

  Read the article

• ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

  - by user223833

  I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

  Read the article

• Secondary fallback/failover network on Cisco ASA

  - by tyranitar

  In my network there is a Cisco ASA 55x0 with "inside" interface (network 192.168.79.0/24) and "outside" interface (network 89.x.x.48/29) There is this nat rule: object network NAToutside nat (inside,outside) dynamic interface and the static route route outside 0.0.0.0 0.0.0.0 89.x.x.49 1 and all ACL rules. Now I have another new outside network by another ISP called "outside2", this network is already natted and the Cisco ASA in in the network 192.168.70.0/24. I would use this network as a fallback one. So I set the nat rule: object network NAToutside2 nat (inside,outside2) dynamic interface and the static route with a different metric route outside2 0.0.0.0 0.0.0.0 192.168.70.1 2 Clearly it doesn't work: when I disconnect the outside ethernet cable no workstation can connect to the Internet throught the outside2 network... What do I need more?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10  | Next Page >