Search Results

Search found 272 results on 11 pages for 'blade chassis'.

Page 10/11 | < Previous Page | 6 7 8 9 10 11  | Next Page >

• erratic response times with Apache 2.0.52 on redhat 4.

  - by Kevin

  Under load, we've noticed response times from Apache vary greatly for the same 7k image. It can range anywhere from .01 seconds to 25 seconds or greater. Unfortunately, due to corporate policy constraints we are pretty much stuck on Apache 2.0.52. I'm at best an Apache novice so I'm in over my head with this problem. My focus recently has turned to our choice of MPM modules. We use the worker model on a dual core hyper threaded blade. It doesn't appear that swapping is an issue, and I don't see any signs of a hardware problem. I've read that worker is optimal on hardware with many CPU's where prefork it more suitable for our specific hardware profile. I can see conceptually how choosing the wrong MPM could result in this erratic behavior, but I'm not confident that it's the root cause here. Has anyone else seen this type of range in your response times for simple static content? What else should I be looking into here?

  Read the article

• How do I speed up and cache mmap file access over NFS on Linux?

  - by Zan Lynx

  The server and client are both 64-bit Ubuntu 10.04 LTS. The application in question is a custom app that uses mmap() for fast random file access. Its ideal state is when the entire file is cached in RAM. The network connections are really fast 10Gb Ethernet. It is a virtual server blade setup. It isn't the network connections slowing things down because everything performs superbly when using a virtual disk (iSCSI to the SAN). But when we run the application on a NFS home directory mount, performance goes to the dogs. It appears that the Linux kernel isn't caching anything. So it is reading every single disk block needed by mmap() accesses over and over and over again. The NFS mount is done through autofs, which has only default settings. /proc/mounts shows the NFS mount is done with the following options: rw,relatime,vers=3,rsize=131072,wsize=131072,namlen=255,hard,proto=tcp,timeo=600,retrans=2,sec=sys,mountaddr=192.168.11.52,mountvers=3,mountproto=tcp,addr=192.168.11.52 How can I make Ubuntu 10.04 cache the file instead of reloading it all the time?

  Read the article

• 20 1TB drives vs. 10 2TB drives in RAID5/6 server

  - by Hunter

  Hi everyone, I will be setting up a server at work and I need some advice on some details. The setup will be one blade-type server (8-core, 16GB RAM) with two subsystems - one for the main storage the other to back it up. I'm shooting for a 20TB array (I know it'll be less after formatting and parity drives). So is there any advantage one way or the other with either 20 1TB drives or 10 2TB drives? I'm not sure right now how many controllers I should have either (in the quote I have is a dual-port controller). I would think two controllers for a server of this size would be a better choice than the dual-port controller (but I really don't know). And would an array of this size have any performance issues in RAID 5 or 6 (I know RAID 5 or 6 are "slower" because of all the parity calculations). Also, these will be either WD RE3 (1TB) or the RE4 (2TB). Oh, also, for the backup array would it be ok to use the WD 2TB green drives (also in RAID5 or 6)?

  Read the article

• Should I buy more RAM for my computer or a better CPU?

  - by Reijer The Coder

  I have recently bought a new laptop, an ASUS N56VJ-S4149H. I bought it to use it in all possible ways I could want, so that would be gaming downloading and streaming movies browsing the web and programming software. So far it has been running great but one thing annoys me a little bit. I frequently play Mount&Blade: Warband, it's a great game and you should check it out. Everything runs smoothly but only when I turn down the 'Texture Detail'. Otherwise it will lag a lot and I can't really play. Now my question is: Is this a problem of not enough RAM? At first I was really sure it was but after thinking about for a while I'm not anymore. My computer only has 4 Gigabytes of RAM and there is still a slot open. So will it improve when I buy another 8 Gigabytes? EDIT: It has an Nvidia GeForce GT 635M inside. and an Intel Core i5 3230M CPU with 2,6 GHz. Help and answers are really appreciated. Thanks to all.

  Read the article

• Oracle’s New Memory-Optimized x86 Servers: Getting the Most Out of Oracle Database In-Memory

  - by Josh Rosen, x86 Product Manager-Oracle

  With the launch of Oracle Database In-Memory, it is now possible to perform real-time analytics operations on your business data as it exists at that moment – in the DRAM of the server – and immediately return completely current and consistent data. The Oracle Database In-Memory option dramatically accelerates the performance of analytics queries by storing data in a highly optimized columnar in-memory format.  This is a truly exciting advance in database technology.As Larry Ellison mentioned in his recent webcast about Oracle Database In-Memory, queries run 100 times faster simply by throwing a switch.  But in order to get the most from the Oracle Database In-Memory option, the underlying server must also be memory-optimized. This week Oracle announced new 4-socket and 8-socket x86 servers, the Sun Server X4-4 and Sun Server X4-8, both of which have been designed specifically for Oracle Database In-Memory.  These new servers use the fastest Intel® Xeon® E7 v2 processors and each subsystem has been designed to be the best for Oracle Database, from the memory, I/O and flash technologies right down to the system firmware.Amongst these subsystems, one of the most important aspects we have optimized with the Sun Server X4-4 and Sun Server X4-8 are their memory subsystems.  The new In-Memory option makes it possible to select which parts of the database should be memory optimized.  You can choose to put a single column or table in memory or, if you can, put the whole database in memory.  The more, the better.  With 3 TB and 6 TB total memory capacity on the Sun Server X4-4 and Sun Server X4-8, respectively, you can memory-optimize more, if not your entire database.   Sun Server X4-8 CMOD with 24 DIMM slots per socket (up to 192 DIMM slots per server) But memory capacity is not the only important factor in selecting the best server platform for Oracle Database In-Memory.  As you put more of your database in memory, a critical performance metric known as memory bandwidth comes into play.  The total memory bandwidth for the server will dictate the rate in which data can be stored and retrieved from memory.  In order to achieve real-time analysis of your data using Oracle Database In-Memory, even under heavy load, the server must be able to handle extreme memory workloads.  With that in mind, the Sun Server X4-8 was designed with the maximum possible memory bandwidth, providing over a terabyte per second of total memory bandwidth.  Likewise, the Sun Server X4-4 also provides extreme memory bandwidth in an even more compact form factor with over half a terabyte per second, providing customers with scalability and choice depending on the size of the database.Beyond the memory subsystem, Oracle’s Sun Server X4-4 and Sun Server X4-8 systems provide other key technologies that enable Oracle Database to run at its best.  The Sun Server X4-4 allows for up 4.8 TB of internal, write-optimized PCIe flash while the Sun Server X4-8 allows for up to 6.4 TB of PCIe flash.  This enables dramatic acceleration of data inserts and updates to Oracle Database.  And with the new elastic computing capability of Oracle’s new x86 servers, server performance can be adapted to your specific Oracle Database workload to ensure that every last bit of processing power is utilized.Because Oracle designs and tests its x86 servers specifically for Oracle workloads, we provide the highest possible performance and reliability when running Oracle Database.  To learn more about Sun Server X4-4 and Sun Server X4-8, you can find more details including data sheets and white papers here. Josh Rosen is a Principal Product Manager for Oracle’s x86 servers, focusing on Oracle’s operating systems and software.  He previously spent more than a decade as a developer and architect of system management software. Josh has worked on system management for many of Oracle's hardware products ranging from the earliest blade systems to the latest Oracle x86 servers. 

  Read the article

• Introducing Oracle System Assistant

  - by B.Koch

  by Josh Rosen One of the challenges with today's servers is getting the server up and running and understanding what all of the steps are once you plug the server in for the first time. So many different pieces come into play: installing drivers, updating firmware, configuring RAID, and provisioning the operating system. All of these steps must be done before you can even start using the server. Finding the latest firmware and drivers, making sure you have the right versions, and knowing that all the different software and firmware components work together properly can be a real challenge. If not done correctly, such as if you separately downloading disk firmware or controller firmware that doesn't match the existing OS drivers, you could experience bugs, performance problems, and incompatibilities. Gone are the days of having to locate the tools and drivers media that shipped with the server only to find out that newer versions of software and firmware are available on the web. Oracle has solved these challenges in the new X3-2 family of servers by introducing Oracle System Assistant. Oracle System Assistant is an innovative tool that is built-in to every new x86 server. It provides step-by-step assistance with configuring the server, updating firmware and drivers, and provisioning the operating system. Once you have completed all of the steps in the Oracle System Assistant tool, the server is ready to use. Oracle System Assistant was designed to be easy and straightforward. Starting it is as simple as pressing F9 when the server is booting. You'll need a keyboard, monitor, and mouse or you can use the remote console feature of Oracle ILOM (Integrated Lights Out Manager) to access a virtual KVM to the server from any machine. From there Oracle System Assistant will walk you through each of the steps necessary to set up your server. After configuring the network settings for Oracle System Assistant, the next step is to check for any new software or firmware for the server. Oracle System Assistant connects back to Oracle using your My Oracle Support account and downloads any updates that were made available to you for this specific server. This is where you really start to see the innovation that went into Oracle System Assistant. Firmware for Oracle ILOM and BIOS, operating system drivers, and other system firmware (including for option cards and disk drivers) come as a single bundle, downloading as a single unit, that has been engineered and tested to work together by Oracle. Oracle System Assistant figures out the right combination for your server, so you don't have to. Now that the server has the latest firmware, Oracle System Assistant will next walk you through configuring the hardware. From Oracle System Assistant, you can configure many Oracle ILOM settings, including the network settings and initial user accounts. This ensures that ILOM is accessible and ready to use. Oracle System Assistant is where all parts of the server come together. In addition to communicating with Oracle ILOM and interacting with BIOS, Oracle System Assistant understands and can configure the storage subsystem. Before installing the operating system, Oracle System Assistant can detect the storage configuration and configure RAID for all disks in the system. At this point, the server is ready to be provisioned with the host operating system. You can use Oracle System Assistant to provision a supported OS, including Oracle Linux, Oracle VM, RHEL, SuSe Linux, and Windows. And by using Oracle System Assistant, you can be sure that the proper OS drivers are installed for each of the installed hardware components. With Oracle System Assistant, initial setup of the server has never been easier. If we can innovate around problems and find solutions to make our servers easier to manage, this reduces IT costs and makes managing servers simpler. I think with Oracle System Assistant we have done just that. Josh Rosen is a Principal Product Manager at Oracle and previously spent more than a decade as a developer and architect of system management software. Josh has worked on system management for many of Oracle's hardware products ranging from the earliest blade systems to the latest Oracle x86 servers.

  Read the article

• bluez 5.19 PS4 controller

  - by Athanase

  I currently have a problem when pairing my computer with a PS4 remote. On my Ubuntu 14.04 I removed everything related with bluez and bluetooth, and I built and installed bluez 5.19. Here are some useful command outputs: jean@system ~ hcitool hcitool - HCI Tool ver 5.19 jean@system ~ hcitool dev Devices: hci0 00:15:83:4C:0C:BB jean@system ~ bluetoothctl [bluetooth]# version Version 5.19 jean@system ~ bluetoothctl [NEW] Controller 00:15:83:4C:0C:BB BlueZ [default] jean@system ~ lsusb Bus 003 Device 012: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) So here is what happens. When I try to hard pair the controller with the computer, by holding the share and ps button for a while, everything works as expected and the pairing is done properly. After a hard pairing if I try the pairing by pressing the ps button only, nothings happen. In order to go it, I first power up the bluetooth dongle: jean@system ~ sudo hciconfig hciX up and then I run the bluetooh deamon bluetoothd: jean@system /usr/libexec/bluetooth ~ ./bluetoothd -d -n bluetoothd[11270]: Bluetooth daemon 5.19 bluetoothd[11270]: src/main.c:parse_config() parsing main.conf bluetoothd[11270]: src/main.c:parse_config() discovto=0 bluetoothd[11270]: src/main.c:parse_config() pairto=0 bluetoothd[11270]: src/main.c:parse_config() auto_to=60 bluetoothd[11270]: src/main.c:parse_config() name=%h-%d bluetoothd[11270]: src/main.c:parse_config() class=0x000100 bluetoothd[11270]: src/main.c:parse_config() Key file does not have key 'DeviceID' bluetoothd[11270]: src/gatt.c:gatt_init() Starting GATT server bluetoothd[11270]: src/adapter.c:adapter_init() sending read version command bluetoothd[11270]: Starting SDP server bluetoothd[11270]: src/sdpd-service.c:register_device_id() Adding device id record for 0002:1d6b:0246:0513 ... bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_sink_server_probe() path /org/bluez/hci0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_source_server_probe() path /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:btd_adapter_unblock_address() hci0 00:00:00:00:00:00 bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_C1_0D_2A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_88_5E_9A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:load_link_keys() hci0 keys 2 debug_keys 0 bluetoothd[11270]: src/adapter.c:load_ltks() hci0 keys 0 bluetoothd[11270]: src/adapter.c:load_connections() sending get connections command for index 0 bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: src/adapter.c:set_did() hci0 source 2 vendor 1d6b product 246 version 513 bluetoothd[11270]: src/adapter.c:adapter_register() Adapter /org/bluez/hci0 registered bluetoothd[11270]: src/adapter.c:set_dev_class() sending set device class command for index 0 bluetoothd[11270]: src/adapter.c:set_name() sending set local name command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:adapter_start() adapter /org/bluez/hci0 has been enabled bluetoothd[11270]: src/adapter.c:trigger_passive_scanning() bluetoothd[11270]: plugins/hostname.c:property_changed() static hostname: system bluetoothd[11270]: plugins/hostname.c:property_changed() pretty hostname: bluetoothd[11270]: plugins/hostname.c:update_name() name: system bluetoothd[11270]: src/adapter.c:adapter_set_name() name: system bluetoothd[11270]: plugins/hostname.c:property_changed() chassis: desktop bluetoothd[11270]: plugins/hostname.c:update_class() major: 0x01 minor: 0x01 bluetoothd[11270]: src/adapter.c:load_link_keys_complete() link keys loaded for hci0 bluetoothd[11270]: src/adapter.c:load_ltks_complete() LTKs loaded for hci0 bluetoothd[11270]: src/adapter.c:get_connections_complete() Connection count: 0 And then I press the ps button of the PS4 controller bluetoothd[11270]: src/adapter.c:connected_callback() hci0 device A4:15:66:C1:0D:2A connected eir_len 5 bluetoothd[11270]: profiles/input/server.c:connect_event_cb() Incoming connection from A4:15:66:C1:0D:2A on PSM 17 bluetoothd[11270]: profiles/input/device.c:input_device_set_channel() idev (nil) psm 17 bluetoothd[11270]: Refusing input device connect: No such file or directory (2) bluetoothd[11270]: profiles/input/server.c:confirm_event_cb() bluetoothd[11270]: Refusing connection from A4:15:66:C1:0D:2A: unknown device bluetoothd[11270]: src/adapter.c:dev_disconnected() Device A4:15:66:C1:0D:2A disconnected, reason 3 bluetoothd[11270]: src/adapter.c:adapter_remove_connection() bluetoothd[11270]: plugins/policy.c:disconnect_cb() reason 3 bluetoothd[11270]: src/adapter.c:bonding_attempt_complete() hci0 bdaddr A4:15:66:C1:0D:2A type 0 status 0xe bluetoothd[11270]: src/device.c:device_bonding_complete() bonding (nil) status 0x0e bluetoothd[11270]: src/device.c:device_bonding_failed() status 14 bluetoothd[11270]: src/adapter.c:resume_discovery() So I don't know what is happening here and a bit of help would be appreciated.

  Read the article

• How can I test blades in MVC Turbine with Rhino Mocks?

  - by Brandon Linton

  I'm trying to set up blade unit tests in an MVC Turbine-derived site. The problem is that I can't seem to mock the IServiceLocator interface without hitting the following exception: System.BadImageFormatException: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B) at System.Reflection.Emit.TypeBuilder._TermCreateClass(Int32 handle, Module module) at System.Reflection.Emit.TypeBuilder.CreateTypeNoLock() at System.Reflection.Emit.TypeBuilder.CreateType() at Castle.DynamicProxy.Generators.Emitters.AbstractTypeEmitter.BuildType() at Castle.DynamicProxy.Generators.Emitters.AbstractTypeEmitter.BuildType() at Castle.DynamicProxy.Generators.InterfaceProxyWithTargetGenerator.GenerateCode(Type proxyTargetType, Type[] interfaces, ProxyGenerationOptions options) at Castle.DynamicProxy.DefaultProxyBuilder.CreateInterfaceProxyTypeWithoutTarget(Type interfaceToProxy, Type[] additionalInterfacesToProxy, ProxyGenerationOptions options) at Castle.DynamicProxy.ProxyGenerator.CreateInterfaceProxyTypeWithoutTarget(Type interfaceToProxy, Type[] additionalInterfacesToProxy, ProxyGenerationOptions options) at Castle.DynamicProxy.ProxyGenerator.CreateInterfaceProxyWithoutTarget(Type interfaceToProxy, Type[] additionalInterfacesToProxy, ProxyGenerationOptions options, IInterceptor[] interceptors) at Rhino.Mocks.MockRepository.MockInterface(CreateMockState mockStateFactory, Type type, Type[] extras) at Rhino.Mocks.MockRepository.CreateMockObject(Type type, CreateMockState factory, Type[] extras, Object[] argumentsForConstructor) at Rhino.Mocks.MockRepository.Stub(Type type, Object[] argumentsForConstructor) at Rhino.Mocks.MockRepository.<>c__DisplayClass1`1.<GenerateStub>b__0(MockRepository repo) at Rhino.Mocks.MockRepository.CreateMockInReplay<T>(Func`2 createMock) at Rhino.Mocks.MockRepository.GenerateStub<T>(Object[] argumentsForConstructor) at XXX.BladeTest.SetUp() Everything I search for regarding this error leads me to 32-bit vs. 64-bit DLL compilation issues, but MVC Turbine uses the service locator facade everywhere and we haven't had any other issues, just with using Rhino Mocks to attempt mocking it. It blows up on the second line of this NUnit set up method: IRotorContext _context; IServiceLocator _locator; [SetUp] public void SetUp() { _context = MockRepository.GenerateStub<IRotorContext>(); _locator = MockRepository.GenerateStub<IServiceLocator>(); _context.Expect(x => x.ServiceLocator).Return(_locator); } Just a quick aside; I've tried implementing a fake implementing IServiceLocator, thinking that I could just keep track of calls to the type registration methods. This won't work in our setup, because we extend the service locator's interface in such a way that if the type isn't Unity-based, the registration logic is not invoked.

  Read the article

• python / sqlite - database locked despite large timeouts

  - by Chris Phillips

  Hi, I'm sure I'm missing something pretty obvious, but I can't for the life of me stop my pysqlite scripts crashing out with a database is locked error. I have two scripts, one to load data into the database, and one to read data out, but both will frequently, and instantly, crash depending on what the other is doing with the database at any given time. I've got the timeout on both scripts set to 30 seconds: cx = sqlite.connect("database.sql", timeout=30.0) and think I can see some evidence of the timeouts in that i get what appears to be a timing stamp (e.g 0.12343827e-06 0.1 - and how do I stop that being printed?) dumped occasionally in the middle of my curses formatted output screen, but no delay that ever gets remotely near the 30 second timeout, but still one of the other keeps crashing again and again from this. I'm running RHEL5.4 on a 64 bit 4 cpu HS21 IBM blade, and have heard some mention about issues about multi-threading and am not sure if this might be relevant. Packages in use are sqlite-3.3.6-5 and python-sqlite-1.1.7-1.2.1, and upgrading to newer versions outside of RedHat's official provisions is not a great option for me. Possible, but not desirable due to the environment in general. I have had autocommit=1 on previously on both scripts, but have since disabled on both, and am now cx.commit()ing on the inserting script and not committing on the select script. Ultimately as I only ever have one script actually making any modifications, I don't really see why this locking should ever ever happen. I have noticed that this is significantly worse over time when the database has gotten larger. It was recently at 13mb with 3 equal sized tables, which was about 1 day's worth of data. creating a new file has significantly improved this, which seems understandable, but the timeout ultimately just doesn't seem to be being obeyed. Any pointers very much appreciated. Thanks Chris

  Read the article

• String method crashes program...

  - by TimothyTech

  Alright so i have two identical string methods... string CreateCust() { string nameArray[] ={"Tom","Timo","Sally","Kelly","Bob","Thomas","Samantha","Maria"}; int d = rand() % (8 - 1 + 1) + 1; string e = nameArray[d]; return e; } string CreateFood() { string nameArray[] = {"spagetti", "ChickenSoup", "Menudo"}; int d = rand() % (3 - 1 + 1) + 1; string f = nameArray[d]; return f; } however no matter what i do it the guts of CreateFood it will always crash. i created a test chassis for it and it always fails at the cMeal = CreateFood(); Customer Cnow; cout << "test1" << endl; cMeal = Cnow.CreateFood(); cout << "test1" << endl; cCustomer = Cnow.CreateCust(); cout << "test1" << endl; i even switched CreateCust with CreateFood and it still fails at the CreateFood Function... NOTE: if i make createFood a int method it does work...

  Read the article

• Laravel4: Checking many-to-many relationship attribute even when it does not exist

  - by Simo A.

  This is my first time with Laravel and also Stackoverflow... I am developing a simple course management system. The main objects are User and Course, with a many-to-many relationship between them. The pivot table has an additional attribute, participant_role, which defines whether the user is a student or an instructor within that particular course. class Course extends Eloquent { public function users() { return $this->belongsToMany('User')->withPivot('participant_role')->withTimestamps(); } } However, there is an additional role, system admin, which can be defined on the User object. And this brings me mucho headache. In my blade view I have the following: @if ($course->pivot->participant_role == 'instructor') { // do something here... } This works fine when the user has been assigned to that particular $course and there is an entry for this user-course combination in the pivot table. However, the problem is the system administrator, who also should be able to access course details. The if-clause above gives Trying to get property of non-object error, apparently because there is no entry in the pivot table for system administrator (as the role is defined within the User object). I could probably solve the problem by using some off-the-shelf bundle for handling role-based permissions. Or I could (but don't want to) do something like this with two internal if-clauses: if (!empty($course->pivot)) { if ($course->pivot->participant_role == 'instructor') { // do something... } } Other options (suggested in partially similar entries in Stackoverflow) would include 1) reading all the pivot table entries to an array, and use in_array to check if a role exists, or even 2) SQL left join to do this on database level. However, ultimately I am looking for a compact one-line solution? Can I do anything similar to this, which unfortunately does not seem to work? if (! empty ($course->pivot->participant_role == 'instructor') ) { // do something... } The shorter the answer, the better :-). Thanks a lot!

  Read the article

• Random servers in Citrix servers suddenly bluescreens (mostly 0x0000008e and 0x0000007e)

  - by Rasmus Rask

  I'm responsible for a Citrix Presentation Server 4.5 farm. Starting Friday 30. November, my servers started to crash randomly. So far we've experienced 80 crashes, so it's obviously becoming an increasingly big problem for us. I have 12+ years experience with IT, so I know the difference between 0 and 1, but I have a hard time cracking this. We've rolled back any recent changes I can think of for different groups of servers, but all groups still seem to crash. I don't have the skills to interpret the memory dumps to find the culprit. Has anyone encountered the same or a similar problem? - might be a generic Windows issue Other than executing "analyze -v" in WinDbg, how do I work my way through the memory dumps to see what actually triggered the BSOD? Any suggested steps in getting to the bottom of this? Any help is greatly appreciated. I can also provide links to kernel memory dumps or WinDbg output if necessary. Thanks! Problem description The majority of the STOP errors we encounter are: 0x0000008e KERNEL_MODE_EXCEPTION_NOT_HANDLED (50%) 0x0000007e SYSTEM_THREAD_EXCEPTION_NOT_HANDLED (26%) 0x00000050 PAGE_FAULT_IN_NONPAGED_AREA (21%) We also see a few 0x0000000a IRQL_NOT_LESS_OR_EQUAL (3%). For both 0x0000008e and 0x0000007e bug checks, the exception code is 0xc0000005 (Access Violation). When opening dump files in WinDbg, most details are exactly the same, for all the 0x0000008e and 0x0000007e bug checks respectively: 0x0000008e Exception address: 0x808bc9e3 Trap frame: [varies] FAILURE_BUCKET_ID: 0x8E_nt!HvpGetCellMapped+97 Probably Caused by (IMAGE_NAME): ntkrpamp.exe 0x0000007e Exception address: 0x808369b6 Exception record address: 0xf70d3be0 Context record address: 0xf70d38dc FAILURE_BUCKET_ID: 0x7E_nt!MmPurgeSection+14 Probably Caused by: memory_corruption About 30% of the crashes happens between 17:00 and 19:00, which leads me to believe this tend to happen more often during logoffs. But then again, only ~15% occurs between 15:00 and 17:00. Summary of farm Citrix Presentation Server 4.5 R06 on Windows Server 2003 R2 SP2 All high priority patches, at least as of October installed Virtualized using VMWare ESX/vSphere 4.1 on HP Proliant BL460c G6 blade servers About 53 Presentation Servers in production, divided into three silos - only one of which, the largest, is affected 2 vCPU's (5 GHz reserved), 8 GB RAM (all reserved) for each Presentation Server Plenty of free disk space Very few printer drivers - automated deletion of non-approved drivers every night ~1.000 peak concurrent users, which is reached at around 10:30 (on weekdays) Number of sessions steadily decline between 15:00 and 19:00 to ~230

  Read the article

• The Koyal Group Info Mag News¦Charged building material could make the renewable grid a reality

  - by Chyler Tilton

  What if your cell phone didn’t come with a battery? Imagine, instead, if the material from which your phone was built was a battery. The promise of strong load-bearing materials that can also work as batteries represents something of a holy grail for engineers. And in a letter published online in Nano Letters last week, a team of researchers from Vanderbilt University describes what it says is a breakthrough in turning that dream into an electrocharged reality. The researchers etched nanopores into silicon layers, which were infused with a polyethylene oxide-ionic liquid composite and coated with an atomically thin layer of carbon. In doing so, they created small but strong supercapacitor battery systems, which stored electricity in a solid electrolyte, instead of using corrosive chemical liquids found in traditional batteries. These supercapacitors could store and release about 98 percent of the energy that was used to charge them, and they held onto their charges even as they were squashed and stretched at pressures up to 44 pounds per square inch. Small pieces of them were even strong enough to hang a laptop from—a big, fat Dell, no less. Although the supercapacitors resemble small charcoal wafers, they could theoretically be molded into just about any shape, including a cell phone’s casing or the chassis of a sedan. They could also be charged—and evacuated of their charge—in less time than is the case for traditional batteries. “We’ve demonstrated, for the first time, the simple proof-of-concept that this can be done,” says Cary Pint, an assistant professor in the university’s mechanical engineering department and one of the authors of the new paper. “Now we can extend this to all kinds of different materials systems to make practical composites with materials specifically tailored to a host of different types of applications. We see this as being just the tip of a very massive iceberg.” Pint says potential applications for such materials would go well beyond “neat tech gadgets,” eventually becoming a “transformational technology” in everything from rocket ships to sedans to home building materials. “These types of systems could range in size from electric powered aircraft all the way down to little tiny flying robots, where adding an extra on-board battery inhibits the potential capability of the system,” Pint says. And they could help the world shift to the intermittencies of renewable energy power grids, where powerful batteries are needed to help keep the lights on when the sun is down or when the wind is not blowing. “Using the materials that make up a home as the native platform for energy storage to complement intermittent resources could also open the door to improve the prospects for solar energy on the U.S. grid,” Pint says. “I personally believe that these types of multifunctional materials are critical to a sustainable electric grid system that integrates solar energy as a key power source.”

  Read the article

• SAS Expanders vs Direct Attached (SAS)?

  - by jemmille

  I have a storage unit with 2 backplanes. One backplane holds 24 disks, one backplane holds 12 disks. Each backplane is independently connected to a SFF-8087 port (4 channel/12Gbit) to the raid card. Here is where my question really comes in. Can or how easily can a backplane be overloaded? All the disks in the machine are WD RE4 WD1003FBYX (black) drives that have average writes at 115MB/sec and average read of 125 MB/sec I know things would vary based on the raid or filesystem we put on top of that but it seems to be that a 24 disk backplane with only one SFF-8087 connector should be able to overload the bus to a point that might actually slow it down? Based on my math, if I had a RAID0 across all 24 disks and asked for a large file, I should, in theory should get 24*115 MB/sec wich translates to 22.08 GBit/sec of total throughput. Either I'm confused or this backplane is horribly designed, at least in a perfomance environment. I'm looking at switching to a model where each drive has it's own channel from the backplane (and new HBA's or raid card). EDIT: more details We have used both pure linux (centos), open solaris, software raid, hardware raid, EXT3/4, ZFS. Here are some examples using bonnie++ 4 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 194MB/s 19% 92MB/s 11% 200MB/s 8% 310/sec 194MB/s 19% 93MB/s 11% 201MB/s 8% 312/sec --------- ---- --------- ---- --------- ---- --------- 389MB/s 19% 186MB/s 11% 402MB/s 8% 311/sec 8 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 324MB/s 32% 164MB/s 19% 346MB/s 13% 466/sec 324MB/s 32% 164MB/s 19% 348MB/s 14% 465/sec --------- ---- --------- ---- --------- ---- --------- 648MB/s 32% 328MB/s 19% 694MB/s 13% 465/sec 12 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 377MB/s 38% 191MB/s 22% 429MB/s 17% 537/sec 376MB/s 38% 191MB/s 22% 427MB/s 17% 546/sec --------- ---- --------- ---- --------- ---- --------- 753MB/s 38% 382MB/s 22% 857MB/s 17% 541/sec Now 16 Disk RAID-0, it's gets interesting WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 359MB/s 34% 186MB/s 22% 407MB/s 18% 1397/sec 358MB/s 33% 186MB/s 22% 407MB/s 18% 1340/sec --------- ---- --------- ---- --------- ---- --------- 717MB/s 33% 373MB/s 22% 814MB/s 18% 1368/sec 20 Disk RAID-0, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 371MB/s 37% 188MB/s 22% 450MB/s 19% 775/sec 370MB/s 37% 188MB/s 22% 447MB/s 19% 797/sec --------- ---- --------- ---- --------- ---- --------- 741MB/s 37% 376MB/s 22% 898MB/s 19% 786/sec 24 Disk RAID-1, ZFS WRITE CPU RE-WRITE CPU READ CPU RND-SEEKS 347MB/s 34% 193MB/s 22% 447MB/s 19% 907/sec 347MB/s 34% 192MB/s 23% 446MB/s 19% 933/sec --------- ---- --------- ---- --------- ---- --------- 694MB/s 34% 386MB/s 22% 894MB/s 19% 920/sec 28 Disk RAID-0, ZFS 32 Disk RAID-0, ZFS 36 Disk RAID-0, ZFS More details: Here is the exact unit: http://www.supermicro.com/products/chassis/4U/847/SC847E1-R1400U.cfm

  Read the article

• Are FC and SAS DAS devices standard enough?

  - by user222182

  Before I ask my questions, here is some background info that may or may not be useful: For the first time I find myself needing a DAS solution. My priority is data through-put in a single direction. I can write large blocks, and I don't need to read at the same time. The server (the data producing device) is not really a typical server, its a very powerful single board computer. As such I have limited options when it comes to the add-in cards I can install since it must use the fairly uncommon interface, XMC. Currently I believe I am limited PCIex8 gen 1 which means that the likely bottle neck for me will be this 16gbps connection. XMC Boards I have found so far offer the following connections: a) Dual 10GBE ethernet controller, total throughput 20gbps b) Dual Quad SAS 2.0 Connectors (SFF-8XXX) HBA (no raid), total throughput 48 gbps c) Dual FC 8gb HBA (no raid), total throughput 16gbps My questions for you guys are: 1) Are SAS and/or FC, and by extension their HBAs, standard enough that I could purchase a Dell or Aberdeen storage server with a raid controller that has external SAS or FC ports and expect that I can connect it to my SAS or FC HBA, be presented with a single volume (if I so configured the storage server), all without having to check for HBA compatibility? 2) On a device like a Dell PowerVault (either DAS or NAS) is there an OS on it to concern myself with, or is it meant to be remotely managed? Is there a local interface in case I cant remotely manage it (i.e. if my single board computer uses an OS not supported by Dell OpenManage). Would this be true of nearly any device which calls itself a DAS? 3) If I purchase some sort of Supermicro storage chassis, installed a raid controller with external connections, is there a nice lightweight OS I can run just for management of the controller? Would I even need an OS since the raid card would be configured pre-boot anyway? 4) It is much easier to buy XMC based 10gigabit ethernet cards (generally dual port). In what ways would I be getting into trouble by using iSCSI as a DAS are direct cabling with SFP+ cables? Thanks in advance

  Read the article

• Custom built machine has much higher power consumption than expected

  - by foraidt

  I built a machine according to the specs of a computer magazine (c't, Germany). According to the magazine, the power consumption should be at around 10W. I don't want to go into the specifics of the hardware but rather ask for general advice on where to look: I updated the BIOS/UEFI version to the latest version, installed all the recommended drivers and unplugged all hardware that's not necessary to boot into Windows. All that was left is the power supply, mainboard, cpu, cpu cooler and one SSD drive. But still I measured a power consumption of 50W, which is 40W more than it should be. I tried booting Linux Mint from a USB stick, so I don't think it's some Windows-related problem.. Where else could I look? Update 1 I dind't want the question to get closed for being too localized but if more details are necessary, here they are: The system is a desktop PC. The power consumption is measured using a Brennenstuhl PM 231 device, which was tested also by c't and they found it quite accurate. The PSU is an Enermax ETL300AWT, the mainboard Intel DH87RL (Socket 1150) and the CPU Intel G3220 (Haswell). Update 2 There is no online version of the article*. The most details I found can be read on its project page (in German, though...) (*)You can pay for downloadable PDFs, however. English translation of that project page Update 3 Regarding the sceptics: It may sound ridiculous but apparently 10W idle consumption is possible with Intel's Haswell architecture. As a kind of proof, there's an additional Blog article explicitly listing the steps needed to reduce the idle consumption to 10W. Additional hardware: I measured the consumption without the HDD, and as expected the usage dropped by around 10W. I have no chassis fans and the CPU fan is a "Scythe Mugen 4" model. It runs at around 600rpm so I think it won't draw much. When stripping off all my extra components I should be at 10W. But I'm not getting anywhere near that. I would be happy to see "just" 15W in the stripped down version but currently I'm not getting below 50W no matter which component I remove. As I see it this cannot be explained by the PSU being less efficient at lower consumption. I also waited half an hour or so (also checked that no Windows updates were running in the background) and the consumption dind't drop by more than a few watts.

  Read the article

• HP UX can not boot from Ignite Tape

  - by Spirit

  We have hp rp2470 server running hp-ux 11.00, with LVM mirroring. As for redundancy we have second rp2470 same hw (same two processors, same ram, same two hdd’s, same number of lan cards). I want to clone first one to the second. For that purpose I am making ignite tape with the following command: make_tape_recovery -x inc_entire=vg00 Ignite tape finishes without problems. When I boot second server from this ignate tape, server is starting to boot, and ignite restore finishes without any errors, only few notes, which are normal. However vmunix is not booting and when restore finishes, it boot to ISL prompt. From this I cannot boot /stand/vmunix. I tried to run recovery shell but no success. When recovery shell ask to do frecover to restore critical files, then I receive error: frecover(5405): unable to open /dev/rmt/0m At first I thought that the problem might be in the difference of the firmware version of the servers: fw version of production server is: Firmware Version 43.50 and fw version of backup server is: Firmware Version 42.19 So i did a fw upgrade of my backup server so that both servers are v43.50, and tried a recovery but again cant boot the system. Next I did another archive tape with -I (Interactive) flag: make_tape_recovery -I -x inc_entire=vg00 and tried recovery with it, again no good. I cannot find any error or warnings on ignite log, and I cannot boot hpux. I am only on ISL prompt. This is what i've noticed on the gsp logs: ************* SYSTEM ALERT ************** SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:18:49 ALERT LEVEL: 6 = Boot possible, pending failure - action required REASON FOR ALERT SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF ON ON ON LED State: Boot Failed. Running non-OS code. Check Chassis and Console Logs for error messages. 0x00000060860010B0 00000000 00000000 - type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A1231 - type 11 = Timestamp 07/27/2003 10:18:49 And another gsp log: Log Entry # 3 : SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:12:20 ALERT LEVEL: 6 = Boot possible, pending failure - action required SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail CALLER ACTIVITY: 1 = test STATUS: 0 CALLER SUBACTIVITY: 0B = implementation dependent REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00 0x00000060860010B0 00000000 00000000 type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A0C14 type 11 = Timestamp 07/27/2003 10:12:20 Type CR for next entry, - CR for previous entry, Q CR to quit. Please note that I can not change anything on the production server. I can only make changes to the backup server. Any help is appreciated.

  Read the article

• Suggestions for splitting server roles amongst Hyper-V virtual servers / RAID6 or RAID10? / AppAssure

  - by Anon

  We have 2 Hyper-V hosts at present running 1 virtual server that was converted from a physical box running all roles. My plan is to split the roles over various virtual machines, upgrading to the latest software versions as I go, and use the backup server as a standby in case the main server fails. AppAssure backup software has a feature called Virtual Standby, so the VHD's can be ready to be fired up on the backup server if necessary. Off-site backups will be done via external USB drive for now. I'm just seeking some input/suggestions into how I'm planning to split the roles out amongst various virtual servers. Also, I'm curious how to setup the storage on the servers. We do not have any NAS's, SAN'S or any budget for this. What would the best RAID level be to use? I'm thinking either RAID6 (which is currently used) however I'm concerned about the write speeds, or RAID10 but again I'm worried that I can only lose 1 drive (from the same mirror) as opposed to any 2 with RAID6. I realise I have a hot swap for this, but what if a further drive fails during a rebuild? Is the write penalty of RAID6 worth the extra reliability over RAID10? Or will it be too slow with all the roles I am planning, therefore RAID10 is my only real option? The reason for the needed redundancy is I am the only technician and I'm not always on-site. Options I've considered: 1) 5 drives in RAID6 set, 200gb for host OS, rest for VM storage. 1 drive for hot swap - this is how it is currently setup 2) 4 drives in RAID10 set, 200gb for host OS, rest for VM storage. 2 drives for hot swap 3) 4 drives in RAID10 set for VM storage, 2 drives in RAID1 set for host OS. No drives for hot swap - While this is probably the best option with the amount of drives I have, I don't like the idea of having no hot swap 4) 3 drives in RAID6 set for VM storage, 2 drives in RAID1 set for host OS. 1 drive for hot swap All options give us enough storage capacity for our files, etc. We don't have any budget for extra drives or extra hot swap HD chassis for the servers. We have about 70 clients and about 150 users. MAIN SERVER Intel Xeon 5520 @ 2.27 GHz (2 processors) 16GB RAM 6 x 1TB Seagate Barracuda ES.2 Enterprise SATA drives Intel SRCSATAWB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: DC01 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM DC02 - Active Directory Domain Controller / DNS server / Global catalog - 1GB RAM Member Server - DHCP server, File server, Print server - 1GB RAM SCCM Member Server - 4GB RAM Third Party Software Member Server - A/V server, Ticketing software, etc - 4GB RAM Exchange 2007 - 4GB RAM - however we are probably migrating to a hosted solution, therefore freeing up resources BACKUP SERVER Intel Xeon E5410 @ 2.33GHz (2 processors) 16GB RAM 6 x 2TB WD RE4 SATA drives Intel SRCSASRB RAID controller Virtual machine workload using Hyper-V on Windows Server 2008 R2: AppAssure backup software - 8GB RAM

  Read the article

• lshw tells me my processor is a 64 bits but my motherboard has a 32 bits width

  - by bpetit

  Recently I noticed lshw tells me a strange thing. Here is the first part of my lshw output: bpetit-1025c description: Notebook product: 1025C (1025C) vendor: ASUSTeK COMPUTER INC. version: x.x serial: C3OAAS000774 width: 32 bits capabilities: smbios-2.7 dmi-2.7 smp-1.4 smp configuration: boot=normal chassis=notebook cpus=2 family=Eee PC... *-core description: Motherboard product: 1025C vendor: ASUSTeK COMPUTER INC. physical id: 0 version: x.xx serial: EeePC-0123456789 slot: To be filled by O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 1025C.0701 date: 01/06/2012 size: 64KiB capacity: 1984KiB capabilities: pci upgrade shadowing cdboot bootselect socketedrom edd... *-cpu:0 description: CPU product: Intel(R) Atom(TM) CPU N2800 @ 1.86GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 slot: CPU 1 size: 798MHz capacity: 1865MHz width: 64 bits clock: 533MHz capabilities: x86-64 boot fpu fpu_exception wp vme de pse tsc ... configuration: cores=2 enabledcores=1 id=2 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 24KiB capacity: 24KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 2.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 13 slot: System board or motherboard size: 2GiB *-bank:0 description: SODIMM [empty] product: [Empty] vendor: [Empty] physical id: 0 serial: [Empty] slot: DIMM0 *-bank:1 description: SODIMM DDR3 Synchronous 1066 MHz (0.9 ns) product: SSZ3128M8-EAEEF vendor: Xicor physical id: 1 serial: 00000004 slot: DIMM1 size: 2GiB width: 64 bits clock: 1066MHz (0.9ns) *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 size: 798MHz capacity: 798MHz capabilities: ht cpufreq configuration: id=2 *-logicalcpu:0 description: Logical CPU physical id: 2.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 capabilities: logical So here I see my processor is effectively a 64 bits one. However, I'm wondering how my motherboard can have a "32 bits width". I've browsed the web to find an answer, without success. I imagine it's just a technical fact that I don't know about. Thanks.

  Read the article

• HTG Explains: Why is Printer Ink So Expensive?

  - by Chris Hoffman

  Printer ink is expensive, more expensive per drop than fine champagne or even human blood. If you haven’t gone paperless, you’ll notice that you’re paying a lot for new ink cartridges — more than seems reasonable. Purchasing the cheapest inkjet printer and buying official ink cartridge replacements is the most expensive thing you can do. There are ways to save money on ink if you must continue to print documents. Cheap Printers, Expensive Ink Ink jet printers are often very cheap. That’s because they’re sold at cost, or even at a loss — the manufacturer either makes no profit from the printer itself or loses money. The manufacturer will make most of its money from the printer cartridges you buy later. Even if the company does make a bit of money from each printer sold, it makes a much larger profit margin on ink. Rather than selling you a printer that may be rather expensive, they want to sell you a cheap printer and make money on an ongoing basis by providing expensive printer ink. It’s been compared to the razor model — sell a razor cheaply and mark up the razor blades. Rather than making a one-time profit on the razor, you’ll make continuing profit as the customer keeps buying razor blade replacements — or ink, in this case. Many printer manufacturers go out of their way to make it difficult for you to use unofficial ink cartridges, building microchips into their official ink cartridges. If you use an unofficial cartridge or refill an official cartridge, the printer may refuse to use it. Lexmark once argued in court that unofficial microchips that enable third-party ink cartridges would violate their copyright and Lexmark has argued that creating an unofficial microchip to bypass this restriction on third-party ink would violate Lexmark’s copyright and be illegal under the US DMCA. Luckily, they lost this argument. What Printer Companies Say Printer companies have put forth their own arguments in the past, attempting to justify the high cost of official ink cartridges and microchips that block any competition. In a Computer World story from 2010, HP argued that they spend a billion dollars each year on “ink research and development.” They point out that printer ink “must be formulated to withstand heating to 300 degrees, vaporization, and being squirted at 30 miles per hour, at a rate of 36,000 drops per second, through a nozzle one third the size of a human hair. After all that it must dry almost instantly on the paper.” They also argue that printers have become more efficient and use less ink to print, while third-party cartridges are less reliable. Companies that use microchips in their ink cartridges argue that only the microchip has the ability to enforce an expiration date, preventing consumers from using old ink cartridges. There’s something to all these arguments, sure — but they don’t seem to justify the sky-high cost of printer ink or the restriction on using third-party or refilled cartridges. Saving Money on Printing Ultimately, the price of something is what people are willing to pay and printer companies have found that most consumers are willing to pay this much for ink cartridge replacements. Try not to fall for it: Don’t buy the cheapest inkjet printer. Consider your needs when buying a printer and do some research. You’ll save more money in the long run. Consider these basic tips to save money on printing: Buy Refilled Cartridges: Refilled cartridges from third parties are generally much cheaper. Printer companies warn us away from these, but they often work very well. Refill Your Own Cartridges: You can get do-it-yourself kits for refilling your own printer ink cartridges, but this can be messy. Your printer may refuse to accept a refilled cartridge if the cartridge contains a microchip. Switch to a Laser Printer: Laser printers use toner, not ink cartridges. If you print a lot of black and white documents, a laser printer can be cheaper. Buy XL Cartridges: If you are buying official printer ink cartridges, spend more money each time. The cheapest ink cartridges won’t contain much ink at all, while larger “XL” ink cartridges will contain much more ink for only a bit more money. It’s often cheaper to buy in bulk. Avoid Printers With Tri-Color Ink Cartridges: If you’re printing color documents, you’ll want to get a printer that uses separate ink cartridges for all its colors. For example, let’s say your printer has a “Color” cartridge that contains blue, green, and red ink. If you print a lot of blue documents and use up all your blue ink, the Color cartridge will refuse to function — now all you can do is throw away your cartridge and buy a new one, even if the green and red ink chambers are full. If you had a printer with separate color cartridges, you’d just have to replace the blue cartridge. If you’ll be buying official ink cartridges, be sure to compare the cost of cartridges when buying a printer. The cheapest printer may be more expensive in the long run. Of course, you’ll save the most money if you stop printing entirely and go paperless, keeping digital copies of your documents instead of paper ones. Image Credit: Cliva Darra on Flickr     

  Read the article

• Recent Innovations to ILOM

  - by B.Koch

  by Josh Rosen If you are wondering how Oracle can make some of the most advanced, reliable, and fault tolerant servers on the market, look no further than Oracle Integrated Lights Out Manager or ILOM.  We build ILOM into every server we create, from Oracle x86 Systems such as X3-2 to the SPARC T-Series family. Oracle ILOM is an embedded service processor, but it's really more than that.  It's a computer within a computer.  It's smart, it's tightly integrated into all aspects of the server's operation, and it's a big reason why Oracle servers are used for some of the most mission-critical workloads out there. To understand the value of ILOM, there is no better place to start than its fault management capability.  We have taken the sophisticated fault management architecture from Solaris, developed and refined over a decade, and built it into each and every ILOM. ILOM detects a potential issue at its earliest stage, watching low-level sensors.   If the root cause of a problem is not clear from a single error reading, ILOM will look for other clues and combine multiple pieces of information to correctly identify a failing component. ILOM provides peace of mind. We tailor our fault management for each new server platform that we produce.  You can rest assured that it's always actively keeping the server healthy.  And if there is a problem, you can be confident it will let you know by sending you a notification by e-mail or trap. We also heard IT managers tell us they needed a Ph.D. in computer engineering to manage today's servers. It doesn't have to be that way.  Thanks to the latest innovations to Oracle ILOM, we present hardware inventory and status in way that makes sense – to anyone.  Green means everything is healthy and red means something is wrong.  When a component needs to be replaced a clear message indicates where the problem is and points you at a knowledge article about that problem.  It's that simple. Simpler management and simple interfaces mean reduced complexity and lower costs to manage.  And we know that's really important. ILOM does all this while also providing advanced service processor features you depend on for managing enterprise class systems.  You can remotely control the server power, interact with a virtual video console for the server, and mount media on the server remotely.  There is no need to spend money on a KVM switch to get this functionality. And when people hear how advanced ILOM is, they can't believe ILOM is free.  All features are enabled and included with each Oracle server that you buy.  There are no advanced licenses you need to purchase or features to unlock. Configuring ILOM has also never been easier.  It is now possible to configure almost all aspects of the server directly from ILOM.  This includes changing BIOS settings, persistently modifying boot order, and optimizing power settings -- all directly from ILOM. But Oracle's innovation does not stop with ILOM.  Oracle has engineered Oracle Enterprise Manager Ops Center to integrate directly with ILOM, providing centralized management across all of our servers. Ops Center will discover each of your Oracle servers over the network by searching for ILOMs.  When it finds one, it knows how to communicate with ILOM to monitoring and configure that server from application to disk. Since every server that Oracle produces, from x86 Systems to SPARC T-Series up and down the line, comes with Oracle ILOM, you can manage all Oracle servers in the same way.  And while all of our servers may have different components on the inside, each with their specialized functions, the way you integrate them and the way you monitor and manage them is exactly the same. Oracle ILOM is state-of-art.  If you are looking for a server that make systems management simple and is easy to integrate and maintain, check out the latest advances to Oracle ILOM. Josh Rosen is a Principal Product Manager at Oracle and previously spent more than a decade as a developer and architect of system management software. Josh has worked on system management for many of Oracle's hardware products ranging from the earliest blade systems to the latest Oracle x86 servers.

  Read the article

• Implementing a Custom Coherence PartitionAssignmentStrategy

  - by jpurdy

  A recent A-Team engagement required the development of a custom PartitionAssignmentStrategy (PAS). By way of background, a PAS is an implementation of a Java interface that controls how a Coherence partitioned cache service assigns partitions (primary and backup copies) across the available set of storage-enabled members. While seemingly straightforward, this is actually a very difficult problem to solve. Traditionally, Coherence used a distributed algorithm spread across the cache servers (and as of Coherence 3.7, this is still the default implementation). With the introduction of the PAS interface, the model of operation was changed so that the logic would run solely in the cache service senior member. Obviously, this makes the development of a custom PAS vastly less complex, and in practice does not introduce a significant single point of failure/bottleneck. Note that Coherence ships with a default PAS implementation but it is not used by default. Further, custom PAS implementations are uncommon (this engagement was the first custom implementation that we know of). The particular implementation mentioned above also faced challenges related to managing multiple backup copies but that won't be discussed here. There were a few challenges that arose during design and implementation: Naive algorithms had an unreasonable upper bound of computational cost. There was significant complexity associated with configurations where the member count varied significantly between physical machines. Most of the complexity of a PAS is related to rebalancing, not initial assignment (which is usually fairly simple). A custom PAS may need to solve several problems simultaneously, such as: Ensuring that each member has a similar number of primary and backup partitions (e.g. each member has the same number of primary and backup partitions) Ensuring that each member carries similar responsibility (e.g. the most heavily loaded member has no more than one partition more than the least loaded). Ensuring that each partition is on the same member as a corresponding local resource (e.g. for applications that use partitioning across message queues, to ensure that each partition is collocated with its corresponding message queue). Ensuring that a given member holds no more than a given number of partitions (e.g. no member has more than 10 partitions) Ensuring that backups are placed far enough away from the primaries (e.g. on a different physical machine or a different blade enclosure) Achieving the above goals while ensuring that partition movement is minimized. These objectives can be even more complicated when the topology of the cluster is irregular. For example, if multiple cluster members may exist on each physical machine, then clearly the possibility exists that at certain points (e.g. following a member failure), the number of members on each machine may vary, in certain cases significantly so. Consider the case where there are three physical machines, with 3, 3 and 9 members each (respectively). This introduces complexity since the backups for the 9 members on the the largest machine must be spread across the other 6 members (to ensure placement on different physical machines), preventing an even distribution. For any given problem like this, there are usually reasonable compromises available, but the key point is that objectives may conflict under extreme (but not at all unlikely) circumstances. The most obvious general purpose partition assignment algorithm (possibly the only general purpose one) is to define a scoring function for a given mapping of partitions to members, and then apply that function to each possible permutation, selecting the most optimal permutation. This would result in N! (factorial) evaluations of the scoring function. This is clearly impractical for all but the smallest values of N (e.g. a partition count in the single digits). It's difficult to prove that more efficient general purpose algorithms don't exist, but the key take away from this is that algorithms will tend to either have exorbitant worst case performance or may fail to find optimal solutions (or both) -- it is very important to be able to show that worst case performance is acceptable. This quickly leads to the conclusion that the problem must be further constrained, perhaps by limiting functionality or by using domain-specific optimizations. Unfortunately, it can be very difficult to design these more focused algorithms. In the specific case mentioned, we constrained the solution space to very small clusters (in terms of machine count) with small partition counts and supported exactly two backup copies, and accepted the fact that partition movement could potentially be significant (preferring to solve that issue through brute force). We then used the out-of-the-box PAS implementation as a fallback, delegating to it for configurations that were not supported by our algorithm. Our experience was that the PAS interface is quite usable, but there are intrinsic challenges to designing PAS implementations that should be very carefully evaluated before committing to that approach.

  Read the article

• How build my own Application Setting

  - by adisembiring

  I want to build a ApplicationSetting for my application. The ApplicationSetting can be stored in a properties file or in a database table. The settings are stored in key-value pairs. E.g. ftp.host = blade ftp.username = dummy ftp.pass = pass content.row_pagination = 20 content.title = How to train your dragon. I have designed it as follows: Application settings reader: interface IApplicationSettingReader { read(); } DatabaseApplicationSettingReader { dao appSettingDao; AppSettings read() { List<AppSettingEntity> listEntity = appSettingsDao.findAll(); Map<String, String> map = new HaspMap<String, String>(); foreach (AppSettingEntity entity : listEntity) { map.put(entity.getConfigName(), entity.getConfigValue()); } return new AppSettings(map); } } DatabaseApplicationSettingReader { dao appSettingDao; AppSettings read() { //read from some properties file return new AppSettings(map); } } Application settings class: AppSettings { private static AppSettings instance; private Map map; Public AppSettings(Map map) { this.map = map; } public static AppSettings getInstance() { if (instance == null) { throw new RuntimeException("Object not configure yet"); } return instance; } public static configure(IApplicationSettingReader reader) { instance = reader.read(); } public String getFtpSetting(String param) { return map.get("ftp." + param); } public String getContentSetting(String param) { return map.get("content." + param); } } Test class: AppSettingsTest { IApplicationSettingReader reader; @Before public void setUp() throws Exception { reader = new DatabaseApplicationSettingReader(); } @Test public void getContentSetting_should_get_content_title() { AppSettings.configure(reader); Instance settings = AppSettings.getInstance(); String title = settings.getContentSetting("title"); assertNotNull(title); Sysout(title); } } My questions are: Can you give your opinion about my code, is there something wrong? I configure my application setting once, while the application start, I configure the application setting with appropriate reader (DbReader or PropertiesReader), I make it singleton. The problem is, when some user edit the database or file directly to database or file, I can't get the changed values. Now, I want to implement something like ApplicationSettingChangeListener. So if the data changes, I will refresh my application settings. Do you have any suggestions how this can be implemented?

  Read the article

• HP SmartArray P400: How to repair failed logical drive?

  - by TegtmeierDE

  I have a HP Server with SmartArray P400 controller (incl. 256 MB Cache/Battery Backup) with a logicaldrive with replaced failed physicaldrive that does not rebuild. This is how it looked when I detected the error: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, Failed) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) unassigned physicaldrive 2I:1:8 (port 2I:box 1:bay 8, SATA, 750 GB, OK) ~# I thought that I had drive 2I:1:8 configured as a spare for Array A and Array B, but it seems this was not the case :-(. I noticed the problem due to I/O errors on the host, even if only 1 physicaldrive of the RAID5 is failed. Does someone know why this could happen? The logicaldrive should go into "Degraded" mode but still be fully accessible from the host os!? I first tried to add the unassigned drive 2I:1:8 as a spare to logicaldrive 2, but this was not possible: ~# /usr/sbin/hpacucli ctrl slot=0 array B add spares=2I:1:8 Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# Interestingly it is possible to add the unassigned drive to the first array without problems. I thought maybe the controller put the array into "failed" state due to the missing spare and protects failed arrays from modification. So I tried was to reenable the logicaldrive (to add the spare afterwards): ~# /usr/sbin/hpacucli ctrl slot=0 ld 2 modify reenable Warning: Any previously existing data on the logical drive may not be valid or recoverable. Continue? (y/n) y Error: This operation is not supported with the current configuration. Use the "show" command on devices to show additional details about the configuration. ~# But as you can see, re-enabling the logicaldrive this was not possible. Now I replaced the failed drive by hotswapping it with the unassigned drive. The status now looks like this: ~# /usr/sbin/hpacucli ctrl slot=0 show config Smart Array P400 in Slot 0 (Embedded) (sn: XXXX) array A (SATA, Unused Space: 0 MB) logicaldrive 1 (698.6 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SATA, 750 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SATA, 750 GB, OK) array B (SATA, Unused Space: 0 MB) logicaldrive 2 (2.7 TB, RAID 5, Failed) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SATA, 750 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SATA, 750 GB, OK) physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SATA, 750 GB, OK) physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SATA, 750 GB, OK) physicaldrive 2I:1:7 (port 2I:box 1:bay 7, SATA, 750 GB, OK) ~# The logical drive is still not accessible. Why is it not rebuilding? What can I do? FYI, this is the configuration of my controller: ~# /usr/sbin/hpacucli ctrl slot=0 show Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: XXXX Cache Serial Number: XXXX RAID 6 (ADG) Status: Enabled Controller Status: OK Chassis Slot: Hardware Revision: Rev E Firmware Version: 5.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Analysis Inconsistency Notification: Disabled Raid1 Write Buffering: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True ~# Thanks for you help in advance.

  Read the article

• Windows 2008 Unknown Disks

  - by Ailbe

  I have a BL460c G7 blade server with OS Windows 2008 R2 SP1. This is a brand new C7000 enclosure, with FlexFabric interconnects. I got my FC switches setup and zoned properly to our Clariion CX4, and can see all the hosts that are assigned FCoE HBAs on both paths in both Navisphere and in HP Virtual Connect Manager. So I went ahead and created a storage group for a test server, assigned the appropriate host, assigned the LUN to the server. So far so good, log onto server and I can see 4 unknown disks.... No problem, I install MS MPIO, no luck, can't initialize the disks, and the multiple disks don't go away. Still no problem, I install PowerPath version 5.5 reboot. Now I see 3 disks. One is initialized and ready to go, but I still have 2 disks that I can't initialize, can't offline, can't delete. If I right click in storage manager and go to properties I can see that the MS MPIO tab, but I can't make a path active. I want to get rid of these phantom disks, but so far nothing is working and google searches are showing up some odd results, so obviously I'm not framing my question right. I thought I'd ask here real quick. Does anyone know a quick way to get rid of these unknown disks. Another question, do I need the MPIO feature installed if I have PowerPath installed? This is my first time installing Windows 2008 R2 in this fashion and I'm not sure if that feature is needed or not right now. So some more information to add to this. It seems I'm dealing with more of a Windows issue than anything else. I removed the LUN from the server, uninstalled PowerPath completely, removed the MPIO feature from the server, and rebooted twice. Now I am back to the original 4 Unknown Disks (plus the local Disk 0 containing the OS partition of course, which is working fine) I went to diskpart, I could see all 4 Unknown disks, I selected each disk, ran clean (just in case i'd somehow brought them online previously as GPT and didn't realize it) After a few minutes I was no longer able to see the disks when I ran list disk. However, the disks are still in Disk Management. When I try and offline the disks from Disk Management I get an error: Virtual Disk Manager - The system cannot find the file specified. Accompanied by an error in System Event Logs: Log Name: System Source: Virtual Disk Service Date: 6/25/2012 4:02:01 PM Event ID: 1 Task Category: None Level: Error Keywords: Classic User: N/A Computer: hostname.local Description: Unexpected failure. Error code: 2@02000018 Event Xml: 1 2 0 0x80000000000000 4239 System hostname.local 2@02000018 I feel sure there is a place I can go in the Registry to get rid of these, I just can't recall where and I am loathe to experiement. So to recap, there are currently no LUNS attached at all, I still have the phantom disks, and I'm getting The system cannot find the file specified from Virtual Disk Manager when I try to take them offline. Thanks!

  Read the article

< Previous Page | 6 7 8 9 10 11  | Next Page >