Search Results

Search found 1446 results on 58 pages for 'dropped'.

Page 10/58 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

  - by kce

  We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

  Read the article

• Ubuntu systematically losing wired connection

  - by Lukasz Baczynski

  I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

  Read the article

• Ubuntu Server Cannot Route to the Internet

  - by ejes

  I've been having this problem for weeks now, and I can't seem to figure out the problem. My server can route the local network and serves it well, however it cannot access the internet. It can't be the router because everything else on this lan can route through the router. I've even switched the ethernet port. Any help would be appreciated. I've tried all the usual places, anyway, here are the configs: root@uhs:~# uname -a Linux uhs 3.0.0-16-generic-pae #28-Ubuntu SMP Fri Jan 27 19:24:01 UTC 2012 i686 i686 i386 GNU/Linux root@uhs:~# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface # auto eth1 # iface eth1 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.3 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 root@uhs:~# ping -c 4 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.334 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.339 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.324 ms 64 bytes from 192.168.0.1: icmp_req=4 ttl=64 time=0.339 ms --- 192.168.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2997ms rtt min/avg/max/mdev = 0.324/0.334/0.339/0.006 ms root@uhs:~# ping -c 4 209.85.145.103 PING 209.85.145.103 (209.85.145.103) 56(84) bytes of data. --- 209.85.145.103 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3023ms root@uhs:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:0c:6e:a0:92:6e inet addr:192.168.0.3 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:6eff:fea0:926e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13131114 errors:0 dropped:0 overruns:0 frame:0 TX packets:10540297 errors:0 dropped:0 overruns:5 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3077922794 (3.0 GB) TX bytes:3827489734 (3.8 GB) Interrupt:10 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7721 errors:0 dropped:0 overruns:0 frame:0 TX packets:7721 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:551950 (551.9 KB) TX bytes:551950 (551.9 KB) root@uhs:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 root@uhs:~# # PRETEND Traceroute root@uhs:~# for i in {1..30}; do ping -t $i -c 1 209.85.145.103; done | grep "Time to live exceeded" root@uhs:~#

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• Bridging 10GbE with 12.04 - bridging works but the bridging computer has no internet access

  - by Donal

  I have been trying to get 12.04 bridging working with two 10GbE cards. I have 2 10GbE cards in a linux box being used only for this bridge, 1 with 2 10GbaseT ports and another with a single CX4 port. I have 2 client computers connected with 10GbaseT cards and the CX4 card connects to a procurve switch. I can get the bridging happening mostly the way that I want, The clients receive dhcp information from the dhcp server (not the bridging machine) and can connect to and properly see the rest of the network. Speeds are ok, not amazing but working on that is another matter. My problem is that the bridging machine has no internet access ... meaning I can't update anything or apt-get anything It can ping all other machines on the local network. I've tried the helpful hints from: https://help.ubuntu.com/community/NetworkConnectionBridge "Enabling Internet Use on the Bridging Computer" and get the following RTNETLINK answers: File exists but dhclient br0 does nothing for me :( I think if it is anything it a multiple route problem as both br0 and eth4 have ipaddresses ... even though I have only set it up so that br0 has one ... Bridge setup details: /etc/network/interface auto br0 iface br0 inet static address 192.168.0.246 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 dns-nameservers 192.168.0.1 dns-search example.com dns-domain example.com #(eth2 & eth3 are the 10GbaseT) #(eth4 is the CX4 connection) pre-up ip link set eth2 down pre-up ip link set eth3 down pre-up ip link set eth4 down pre-up brctl addbr br0 pre-up brctl addif br0 eth4 eth3 eth2 pre-up ip addr flush dev eth3 pre-up ip addr flush dev eth2 pre-up ip addr flush dev eth4 post-down ip link set eth4 down post-down ip link set eth2 down post-down ip link set eth3 down post-down ip link set br0 down post-down brctl delif br0 eth2 eth3 eth4 post-down brctl delbr br0 ifconfig -a br0 Link encap:Ethernet HWaddr 00:15:17:22:20:34 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:17ff:fe22:2034/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4957 errors:0 dropped:0 overruns:0 frame:0 TX packets:1077 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:596320 (596.3 KB) TX bytes:139952 (139.9 KB) eth4 Link encap:Ethernet HWaddr 00:60:dd:47:7c:05 inet addr:192.168.0.57 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:7c05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:15391 errors:0 dropped:51 overruns:0 frame:0 TX packets:1207 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5916769 (5.9 MB) TX bytes:154312 (154.3 KB) Interrupt:70 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth4 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth4

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• Is the TCP protocol good enough for real-time multiplayer games?

  - by kevin42

  Back in the day, TCP connections over dialup/ISDN/slow broadband resulted in choppy, laggy games because a single dropped packet resulted in a resync. That meant a lot of game developers had to implement their own reliability layer on top of UDP, or they used UDP for messages that could be dropped or received out of order, and used a parallel TCP connection for information that must be reliable. Given the average user has faster network connections now, can a real time game such as an FPS give good performance over a TCP connection?

  Read the article

• Several IPs for my VPS

  - by Serafim

  I bought vps on santrex.net but can't receive any reply from support. My Problem: I have 5 ip but it pings only 1!!! I can't setup DNS because I need 2 ip minimum . Could you help me to activate other my IPs? root@spnova:~# ifconfig eth0 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.100 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163342 errors:0 dropped:0 overruns:0 frame:0 TX packets:13585 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32862185 (32.8 MB) TX bytes:15189036 (15.1 MB) eth0:0 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.101 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.102 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:2 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.103 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:3 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01 inet addr:188.72.240.104 Bcast:188.72.240.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:11885 errors:0 dropped:0 overruns:0 frame:0 TX packets:11885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8124693 (8.1 MB) TX bytes:8124693 (8.1 MB) root@spnova:~# nano /etc/network/interfaces # Auto generated eth0 interfaces auto eth0 lo iface eth0 inet static address 188.72.240.100 netmask 255.255.255.0 up route add -net 188.72.225.0 netmask 255.255.255.0 dev eth0 up route add default gw 188.72.225.1 iface lo inet loopback auto eth0:0 iface eth0:0 inet static address 188.72.240.101 netmask 255.255.255.0 auto eth0:1 iface eth0:1 inet static address 188.72.240.102 netmask 255.255.255.0 auto eth0:2 iface eth0:2 inet static address 188.72.240.103 netmask 255.255.255.0 auto eth0:3 iface eth0:3 inet static address 188.72.240.104 netmask 255.255.255.0

  Read the article

• How do I tell ubuntu to send traffic to a single IP through eth6?

  - by flashnode

  I want to ensure that all IP traffic going to 172.16.60.62 uses eth6. Please provide complete commands because my linux-fu is rusty. The host is running Ubuntu Precise 12.04 user@host:~$ ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:e0:81:72:fe:c9 inet addr:172.16.60.122 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe72:fec9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:128500 errors:0 dropped:0 overruns:0 frame:0 TX packets:29082 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67524823 (67.5 MB) TX bytes:2217634 (2.2 MB) Interrupt:71 Base address:0x6000 user@host:~$ ifconfig eth6 eth6 Link encap:Ethernet HWaddr 00:60:dd:47:81:35 inet addr:172.16.60.61 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:8135/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:109610 errors:0 dropped:0 overruns:0 frame:0 TX packets:109388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10785630 (10.7 MB) TX bytes:10754350 (10.7 MB) Interrupt:70 user@host:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.60.1 0.0.0.0 UG 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth3

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Ubuntu-VirtualBox-LikeWiseOpen network disaster

  - by Sergio

  I've a virtual machine on VirtualBox 4.1.4 with Ubuntu 11.04. It was working perfectly, but after a reboot something really wrong happened: I wasn't able to connect to the internal network (same for NAT). $ sudo dhclient -v Internet Systems Consortium DHCP Client 4.1.1-P1 Copyright 2004-2010 Internet System Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Error creating socket to list interfaces; Permission denied Can't get list of interfaces. The network interface is PCnet-FAST III. Additional information: $ uname -a Linux LinuxFileServer 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/Linux Any ideas? Thanks EDIT: $ sudo ifconfig -a eth1 Link encap:Ethernet HWaddr 08:00:27:af:f2:c7 indirizzo inet6: fe80::a00:27ff:feaf:f2c7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:1000 Byte RX:0 (0 B) Byte TX:3870 (3.8 KB) Interrupt:10 lo Link encap:Loopback locale indirizzo inet:127.0.0.1 Maschera:255.0.0.0 indirizzo inet6: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisioni:0 txqueuelen:0 Byte RX:960 (960.0 B) Byte TX:960 (960.0 B)

  Read the article

• How can I find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• EC2 instance is blocking all outbound connections, how to diagnose/fix?

  - by Fraggle

  My EC2 instance is blocking all outbound connections. wget http://www.google.com ==> Hangs ping google.com ==>hangs ssh user@anyserver ==>hangs I ran : sudo iptables -F to eliminate all rules to no avail AWS Management console shows Security Group for that instance has Inbound rule allowing ssh and port 80. Can't find anything about Outbound rules there. Rebooted instance, no change. If anyone knows how to diagnose or fix, please help. Adding info: [ec2-user@ip-10-112-62-73 ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3D:06:31:BB inet addr:10.112.62.73 Bcast:10.112.63.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3dff:fe06:31bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1933 errors:0 dropped:0 overruns:0 frame:0 TX packets:1764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164075 (160.2 KiB) TX bytes:343256 (335.2 KiB) Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:672 (672.0 b) TX bytes:672 (672.0 b) [ec2-user@ip-10-112-62-73 ~]$ ip route show 10.112.62.0/23 dev eth0 proto kernel scope link src 10.112.62.73 default via 10.112.62.1 dev eth0

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• Configure static IPv6 on Ubuntu

  - by Charles Offenbacher

  I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• IPTables forward from only one ip on my server

  - by user1307079

  I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

  Read the article

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Ubuntu - wireless connection works great but wired is totally dead

  - by Dan

  I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

  Read the article

• "Network is unreachable" When pinging google, can connect to internal computers on debian VM

  - by musher

  Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >