Search Results

Search found 2516 results on 101 pages for 'gigabit ethernet'.

Page 10/101 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Can I connect a switch to a router?

    - by jasondavis
    Ok sorry if this is the most basic question in the world but for years I have needed more ethernet ports in my room and my whole house is wired with 1 ethernet port in each room, I also wanted to be able to plug into the room ethernet port with another router to get more plugins and that wasn't possibe I don't think. So can you plug a switch into this and have more ports with just as much speed?

    Read the article

  • OpenVPN Server Ethernet Bridging Question

    - by Hooplad
    Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

    Read the article

  • Cat 6 Only 100mbit speed

    - by Stu2000
    I tried two different cat6 cables directly connected between my two ubuntu machines. This one I ordered online: http://www.amazon.co.uk/gp/product/B002SQPDXS/ref=wms_ohs_product only achieves 100mbit speeds, but does appear to be supporting cross-talk (direct pc to pc), the other cat 6 cable, worked perfectly and gets the full 1gigabit speed. Both tests were performed using ftp and checking the network monitor with direct pc to pc connection. Did the product from amazon lie to me or do I need to manually set a setting somewhere in ubuntu for some cables? I had thought 10 quid for 20m of gigabit ethernet cable was a bit cheap, you get what you pay for... Regards, Stu Update: It seems that after rebooting, the device is set to 1000mbit sec when looking it up with sudo ethtool eth0 However after a while, this will drop down to just 100, after which to reset it to 1000 again, I have to reboot, and simply unpugging and re-plugging in the cable doesn't do it. I tried setting this in networking config file as suggested here: auto eth0 iface eth0 inet static pre-up /usr/sbin/ethtool -s eth0 speed 1000 duplex full but that resulted in my networking failing to start. Is there a problem with my 'auto-negotiation' or something? Can I manually override a setting to 1000mbit?

    Read the article

  • System network service uncompatable after harddrive change and format

    - by NStephenH
    After changing out the hard drive in my dell optiplex 750, and reinstalling ubuntu, my computer tells me the system network services are not compatable. Because my cd drive does not work, I installed this by placing the hard drive in another computer an dusign the mini.iso to install it. I need networking capabilities becuase I want to use this computer as a web server. The on-board ethernet card is a intel 82566 something. If you need more information, and can tell me how to get it, just ask. Please help.

    Read the article

  • 12.04 drops Wired Network if Wireless connects

    - by mitt10tim
    This is a little different then most of the questions I have seen here. When I am at my office I keep my Lenovo Thinkpad t61p running Ubuntu 12.04 x64 connected via wired Ethernet. I also typically leave the wireless radios on. After a recent update the behavior of laptop in regards to the networks has changed. It used to be that if the laptop had a wired connection, the wired would supersede the wireless. Now, when I get to work and plug the laptop in and power it up, it connects via wired (correct behavior), shortly after the wireless begins searching for its favorite network (also correct) but as soon as it finds a network to connect to, I lose Internet. If I disconnect from the wireless network, leaving the wireless radios powered on, and refresh the wired connection, all is well again. Powering down the wireless radios also corrects the problem. How can I set this up so that the wired network (if available) always has precedence over the wireless?

    Read the article

  • how to connect to ethernet printer throught python?

    - by Prasanth
    How can i connect and send data to a Ethernet receipt printer Epson-T88V through python2.7, i have set the ipaddress of the Ethernet printer manually and the utility software communication is also successful. How do i detect and connect to these printers and send data to print. Is there and module for Ethernet connection in python. Using more than one Ethernet printer and separate data to be printed simultaneously from a single system, i am using windows xp and python 2.7 hope i am clear Thanks.

    Read the article

  • How to Set Linux Bonding Interface to Gigabit

    - by Kyle Brandt
    I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

    Read the article

  • Linux/bsd tcp load balancing with 10 gigabit ethernet

    - by user37899
    Okay, I've been looking at layer 4 load balancing solutions for 10 gigabit links. I need the following properties Works at 10Gig ethernet speeds. Can support long live tcp connections. up to 1mil live tcp connections. Balancer not involved in the return path. Fault tolerant with tcp session fail over. low latency and good through put. can be scripted. Either a software or hardware solution. Can it be done? Anyone doing this?

    Read the article

  • Looking for a good 16 to 24 gigabit switch for home office

    - by MartinB
    Hi I currently working on my new home office and I want to take that occasion to wire some parts of my house with cat6 Ethernet. To make all this work, I'm looking for a gigabit switch with at least 16 ports (but I would prefer 24 to have some room to grow) that is reliable and quiet. I've about 250$ to put on that. The options I'm looking for now are - DLink 1024D - Netgear JGS524 Would you recommend (or not) one of these switches ? Have you some other suggestions ? Thanks

    Read the article

  • Slow write speeds on new Gigabit home file server

    - by Ryan Holder
    So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

    Read the article

  • Using VLC to Unicast High Definition Webcam over local gigabit LAN with low/zero delay

    - by Robin Day
    We're setting up a webcam "window" between two offices in the same buildilng. The two PC's are connected to the same gigabit switch. We're using VLC to stream the webcam over HTTP using the following commands. vlc dshow:// :dshow-caching="0" :dshow-size="640x480" :sout=#transcode{vcodec=h264,vb=0,scale=0}:http{mux=ffmpeg{mux=flv},dst=:8080/} :no-sout-rtp-sap :no-sout-standard-sap :ttl=1 :sout-keep vlc http://192.168.0.1:8080 :http-caching="0" Even with the caching set to zero, the delay in the image is a good 2-3 seconds. The CPU usage of each pc is also maxed. I'm guessing it's the transcoding that's causing much of the delay. Can anyone give me some changes to these command lines that will reduce the transcoding power, or send the webcam over a different protocol, or anything that will reduce the delay of the cameras? Bandwidth is not an issue at all as the pc's can be connected to a dedicated switch/vlan if required.

    Read the article

  • Hyper-V Virtual Ethernet Adapter not working probperly - Code 31 on Host

    - by Chris S
    I have a Windows 8.1 machine with Hyper-V installed. From a "clean" Hyper-V configuration I open Virtual Switch Manager, create an External switch with "Allow management operating system to share this network adapter", click OK. Everything seems to work properly but the host loses network connectivity. Opening Device Manager, the "Hyper-V Virtual Ethernet Adapter" is shown under the Network Adapter section with a yellow triangle, and the following message: This device is not working properly because Windows cannot load the drivers required for this device. (Code 31) An object ID was not found in the file. I tried "Uninstalling" the device, seems to work, but the device doesn't actually remove. I tried removing and re-adding the Hyper-V feature completely, no difference. Tried scf /scannow, no problems. System and Application logs show no errors. The Hyper-V-VMMS Networking log shows the following: Log Name: Microsoft-Windows-Hyper-V-VMMS-Networking Source: Microsoft-Windows-Hyper-V-VMMS Date: 10/24/2013 10:53:07 AM Event ID: 26088 Description: Failed to apply static IP settings to internal Ethernet adapter {A813DE9A-BE70-4FAE-AD31-BE4D54505A4B} ('885435B8-BE65-4EE9-826D-AB56035237ED'): Unspecified error (0x80004005). If I try to remove the Virtual Switch in Hyper-V Virtual Switch Manager I get this in that same log: Log Name: Microsoft-Windows-Hyper-V-VMMS-Networking Source: Microsoft-Windows-Hyper-V-VMMS Date: 10/24/2013 11:19:47 AM Event ID: 26142 Description: Failed while removing virtual Ethernet switch. Trying to remove the Virtual Switch leads to an error: Error applying Virtual Switch Properties changes Failed while removing virtual Ethernet switch. VM Networking does work.

    Read the article

  • Fast Ethernet module for Cisco 2620

    - by Kenny Rasschaert
    I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

    Read the article

  • Portable, battery-powered, wireless access point, ethernet adapter

    - by Jed
    I am in need of an adapter that will convert an ethernet port into a wireless access point. I have found a handful of devices, but I'm unable to find a device that is battery powered. Does a self-powered wireless access point even exist? The particular scenario that I will be using the device for is not your typical computer/PC scenario. For the curious, here's a bit of background on the problem I'm trying to solve: I make devices (controllers) that monitor water systems. Our controllers have a Webserver that serves out web pages so that users can configure the controller's settings. Typically, the user will use a cross-over cable to connect directly to the controller's ethernet port with their laptop to gain access to the controller's web pages. Now that tablets (devices that don't have an ethernet port - iPad, for example) are becoming more common, I need to find a device that will convert the controller's ethernet port into a wireless access point so that the user can connect to the controller's web pages via Wi-Fi or Bluetooth. It's worth noting that this wireless device that I'm looking for will NOT be permanently installed on the controller. It will be a portable device that the user will use on any of his controllers when he needs to make a connection to the controller. If you know of a device that will solve the scenario that I mention above, please share your info.

    Read the article

  • How do I connect my NetXtreme BCM5755M Gigabit Ethernet PCI Express in y Dell latitude d630?

    - by Stanton.Sculpture
    Trying to get my 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02) working with my wifi. I just installed Raring Ringtail on this dell latitude D630 and I can't get it to connect without a wifi dongle. This is what I got when I typed sudo lshw -c network: *-network description: Ethernet interface product: NetXtreme BCM5755M Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 02 serial: 00:21:70:98:04:32 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 firmware=5755m-v3.29 latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:fe8f0000-fe8fffff *-network description: Wireless interface physical id: 2 bus info: usb@2:1 logical name: wlan0 serial: 7c:dd:90:11:a0:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.8.0-31-generic firmware=0.29 ip=10.0.0.8 link=yes multicast=yes wireless=IEEE 802.11bgn Also, when I go to additional drivers in the software and updates settings, no proprietary drivers show up. I've tried sudo apt-get install b43-fwcutter firmware-b43-installer because it worked on a bunch of old Dell laptops that I converted over before, but it didn't work on this one. Is this driver even compatible with wifi? Please help.

    Read the article

  • Wired connection to windows ISC stopped working

    - by cmpickle
    I have had my Linux box connected to the internet through a Windows computer by wiring them together with a cat5 cable then the Windows is connected wireless to a router. This setup has worked since I got the Linux box but just yesterday stopped working. The changes that occurred were: I changed networking so that I was connecting the Linux box and Windows computer through a second router so during that time the Linux box went through a router to connect to the Windows computer that was still connected wireless to the first router. The Internet didn't work on the Linux box at the time they second router was involved when I removed it and directly connected the Linux box and Windows the Internet worked again. Another thing that changed was that I had disconnected my Windows computer from all network connections and deleted them to make my Ethernet work better. Also at that time my dad had I connect the Windows to a third router and changed some settings in it. After reconnecting this time the connection between the router and the windows would not establish. If anyone has any ideas as to why this is I would greatly appreciate it!

    Read the article

  • How to make ip Address static (eth0)

    - by Jordan Angelucci
    I'm having a really hard time configuring ubuntu 13.04 to have a static ip address. I have tried multiple solutions but everytime I reboot (can't do the network reset command because ubuntu freezes) I end up with no connection. Here is what I get when i type ifconfig into the terminal: eth0 Link encap:Ethernet HWaddr 10:bf:48:bc:07:cb inet addr:192.168.0.8 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::12bf:48ff:febc:7cb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1763067 errors:0 dropped:0 overruns:0 frame:0 TX packets:1024326 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2284491220 (2.2 GB) TX bytes:136809317 (136.8 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1840 errors:0 dropped:0 overruns:0 frame:0 TX packets:1840 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:185688 (185.6 KB) TX bytes:185688 (185.6 KB) I have also tried this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.160 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 24.222.0.94 dns-nameservers 24.222.0.95 If anyone could help me it would be very much appreciated.

    Read the article

  • How do I choose which Ethernet Adapter to bridge in VMPlayer

    - by Catherine MacInnes
    I am running vmplayer 3.1.0 on Ubuntu. The host machine has four ethernet adapters that are configured to run on four different subnets. I need to run four VMs each with a single ethernet adapter bridged onto a specific one of the physical ethernet adapters. Does anyone know how to do this? Am I simply exceeding the capabilities of vmplayer and have to go to one of the other vmware products, if so, which one. Note that I have no need to create additional VMs, these are VMs that are being given to me by companies that want us to develop software for their products.

    Read the article

  • How to connect laptop with telephone using WI-FI? (ethernet)

    - by rmaster
    What I did: 1)added new wireless network in wireless network settings and gave it SSID 2)gave laptop the IP like 192.168.0.1, mask: 255.255.255.0, gateway: 192.168.0.2 3)gave the telephone with wifi the same mask but IP and gateway rewersed But telephone can not find my new wireless network(it can find all other networks), computer also can not find it. where is error? how to make it visible and working? if my steps are wrong tell me correct way to establish this connection via wi-fi

    Read the article

  • Encryption over gigabit carrier ethernet

    - by Roy
    I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

    Read the article

  • House Wiring for Ethernet/Coax/Power

    - by Adam Kragt
    Hoping this is the right place to post, the rest didn't seem to fit. If not, I apologize. Remodeling my house and want to wire up each room with Ethernet/coax wall ports. Both Ethernet, coax and power will be running through the sub-floor. I've read that there needs to be 2 ft between power cables and Ethernet to limit/prevent interference. Is this true? If not, does anyone know what the distance is? Thanks!

    Read the article

  • cheap gigabit switch for small business

    - by neoice
    my friend's business is currently borrowing my Adtran 1224R and is very happy with it. it's configured with a few VLANs to segment customers, internal traffic and public wifi. port 1 is a "trunk" port to the router, a chunky Linux box with iptables+NAT. they push a lot of traffic over the LAN (data backups) and really need gigabit. besides, I'd like my Adtran back :P my goal is to find a cheap(ish) switch that can function as a drop-in replacement. it looks like VLAN trunking is actually part of the 802.1q spec, so anything with VLAN support should cover the current trunk-to-router setup. it's nice to have both a web interface and SSH, but I can configure it either way if needed. things like the Netgear GS724T have caught my eye, but it seems like none of the hardware in the $300-500 range have really solid reviews. I'm concerned that "cheaper" hardware might not work for a network full of power users. does anyone have a recommendation for the Netgear GS724T or a switch that will meet my needs?

    Read the article

  • Bonding: works only for download

    - by Crazy_Bash
    I would like to install bonding with 4 links with mode 4. but only "download/receiving" works with bondig. for transmitting the system chooses one link. ifconfig bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB) those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0 /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 mode 6

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >