Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 10/1221 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Neighbour table overflow on Linux hosts related to bridging and ipv6

  - by tim

  Note: I already have a workaround for this problem (as described below) so this is only a "want-to-know" question. I have a productive setup with around 50 hosts including blades running xen 4 and equallogics providing iscsi. All xen dom0s are almost plain Debian 5. The setup includes several bridges on every dom0 to support xen bridged networking. In total there are between 5 and 12 bridges on each dom0 servicing one vlan each. None of the hosts has routing enabled. At one point in time we moved one of the machines to a new hardware including a raid controller and so we installed an upstream 3.0.22/x86_64 kernel with xen patches. All other machines run debian xen-dom0-kernel. Since then we noticed on all hosts in the setup the following errors every ~2 minutes: [55888.881994] __ratelimit: 908 callbacks suppressed [55888.882221] Neighbour table overflow. [55888.882476] Neighbour table overflow. [55888.882732] Neighbour table overflow. [55888.883050] Neighbour table overflow. [55888.883307] Neighbour table overflow. [55888.883562] Neighbour table overflow. [55888.883859] Neighbour table overflow. [55888.884118] Neighbour table overflow. [55888.884373] Neighbour table overflow. [55888.884666] Neighbour table overflow. The arp table (arp -n) never showed more than around 20 entries on every machine. We tried the obvious tweaks and raised the /proc/sys/net/ipv4/neigh/default/gc_thresh* values. FInally to 16384 entries but no effect. Not even the interval of ~2 minutes changed which lead me to the conclusion that this is totally unrelated. tcpdump showed no uncommon ipv4 traffic on any interface. The only interesting finding from tcpdump were ipv6 packets bursting in like: 14:33:13.137668 IP6 fe80::216:3eff:fe1d:9d01 > ff02::1:ff1d:9d01: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:9d01, length 24 14:33:13.138061 IP6 fe80::216:3eff:fe1d:a8c1 > ff02::1:ff1d:a8c1: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:a8c1, length 24 14:33:13.138619 IP6 fe80::216:3eff:fe1d:bf81 > ff02::1:ff1d:bf81: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:bf81, length 24 14:33:13.138974 IP6 fe80::216:3eff:fe1d:eb41 > ff02::1:ff1d:eb41: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:eb41, length 24 which placed the idea in my mind that the problem maybe related to ipv6, since we have no ipv6 services in this setup. The only other hint was the coincidence of the host upgrade with the beginning of the problems. I powered down the host in question and the errors were gone. Then I subsequently took down the bridges on the host and when i took down (ifconfig down) one particularly bridge: br-vlan2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5286 (5.1 KiB) TX bytes:726 (726.0 B) eth0.2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1801 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:126228 (123.2 KiB) TX bytes:1464 (1.4 KiB) bridge name bridge id STP enabled interfaces ... br-vlan2158 8000.0026b9fb162c no eth0.2158 br-vlan2159 8000.0026b9fb162c no eth0.2159 The errors went away again. As you can see the bridge holds no ipv4 address and it's only member is eth0.2159 so no traffic should cross it. Bridge and interface .2159 / .2157 / .2158 which are in all aspects identical apart from the vlan they are connected to had no effect when taken down. Now I disabled ipv6 on the entire host via sysctl net.ipv6.conf.all.disable_ipv6 and rebooted. After this even with bridge br-vlan2159 enabled no errors occur. Any ideas are welcome.

  Read the article

• How to install Archlinux on a acer emachines em350 ?

  - by zillion

  Do a 64 bits version will work better if the cpu is 64 bits capable ? Can I remove all added stuffs on Archbang or CTKArchLive to return to plain Archlinux with openbox that I can configure myself easily, so I can install Archlinux faster ? I tried and installed Arch properly but I need to install the broadcom bcm 4727 driver (b43,wl,sta,open source), which driver do I need and how can I install it by my usb on Archlinux CLI made with base, sudo and wireless_tools only ?

  Read the article

• Little girl friendly versions of Linux (or themes for Linux)

  - by Hamish Downer

  I'm going to install Linux on a PC for a daughter (age 7) of a friend of mine. I recently came across Hannah Montana Linux. The parents don't want a commercially branded thing going on, so no Hannah Montana. But I was wondering if there were other linux distros - or desktop themes - that would be cool for a 7 year old girl. All suggestions welcome.

  Read the article

• How to stop a infinite running process(ztail) started by a ssh session after that session is closed

  - by Sanath Adiga

  I have a peculiar problem. My server supports multiple ssh session simultaneously, so that multiple admins can manage it simultaneously. We have a command which calls ztail to show the compressed log files and when the current ssh session is closed (without pressing ctrlc, to stop the tail command), the command should ideally stop working. But what I observed when I start a new ssh session is that the process ztail is still running in the background and consuming CPU, even though the previous session was closed. How can I determine when the session is closed, so that I can use that variable/flag to close/stop any commands initiated by that previously closed session?

  Read the article

• Dropped connections between Linux Servers in Data Center

  - by Emil H

  I have a number of linux servers at a us-based datacenter. The servers were installed by the hosting company, and are running fedora core. We're experiencing problems with dropped connections. The issue seems to be that when we attempt to connect to one of the other servers after a period of inactivity, the first connection attempt will fail, and sometimes the second. However, after that the connection succeds and it works for a while. This happens for both mysql connections and raw socket connections, but only seems to occur when connecting to some of our servers. The confusing part is that it some of the servers for which we see different behaviors have identical hardware configuration and software. For example, it happens when connecting to a server called mysql2, but not for a server called mysql3. These servers were installed at the same time, but the same specifications. The problem can be reproduced somewhat reliably, but only after waiting fifteen minutes to half an hour. This makes it hard to diagnose, and even harder since I'm not really sure what to look for. I realize that connections sometimes failed, and that we should write our applications to compensate for this but these servers all in the same data center. Why would it matter if two servers haven't communicated for a while? Does anybody have an idea what might be causing this? Is it a server configuration problem or a network problem that I should contact the hosting company about. What do I tell them to look for? Unfortunately our experience has been that the support staff doesn't investigate problems in depth unless we give them detailed directions.

  Read the article

• Linux Newbie: SSH or VNC for linux admin tasks

  - by Dirk

  Longtime Windows user, looking to get my feet wet with Linux. Since Windows makes comparatively little use of the command line, I'm naturally more comfortable with GUI tools for remote server administration tasks. However, before i rush out and install a VNC server on my Linux box, I want to get a sense of how many of Linux's various packages actually offer GUI front end. If not many, then it's probably not worth the effort.

  Read the article

• rfkill unblock all does not activate a certain wireless card

  - by Davidos

  With an intel 1000 wireless card; rfkill list 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: yes Hard blocked: no rfkill unblock all 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no Why does my wireless card not turn on?

  Read the article

• Best Linux dist for .NET developer looking to learn Groovy (and never used Linux)

  - by blade7

  Hi, I am planning to learn Groovy, but I want to do so on a Linux OS (because such an open minded approach will teach me more about IT and I have Windows Server VMs). Anyway, which Linux distro is the easiest to use and requires the least amount of knowledge on commands etc? As I am new to Linux, I want a dist. which doesn't require command-level knowledge (I am not at this level with Linux but I am with Windows Server). Which dist would be most suitable for me and has development utilities built in? Thanks

  Read the article

• VNC Server running on Linux machine to access all the terminals open on the Linux

  - by goldenmean

  I have a Linux Ubuntu(11.10) box at work, on which I open 4 terminals and execute different processes(my code). I run vncserver on this Linux box, so as to access it remotely. When I login to my office Windows PC using vpn, I would like to connect to this office Linux desktop using VNC Client and be able to see all the Linxu desktop which had my 4 open terminals executing the programs. How to use VNC to view Desktop of Linux PC and all the terminals associated to that which I opened to execute my programs?

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Linux VLAN Bridge

  - by raspi

  I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Run a service after networking is ready on Ubuntu?

  - by TK Kocheran

  I'm trying to start a service that depends on networking being started, whenever the computer is rebooted. I have a few questions: Is this easily possible from an /etc/init.d script? I have tried creating a script here (conforming to the standards), but I'm really doubtful that it's even running on boot, let alone working. When I test it manually, it works. I've seen the new Upstart service, but as far as how that actually works, I'm completely in the dark. How can I make a script that runs on boot which runs after networking has been started? If I could run it after connected to wireless network, even better :)

  Read the article

• Linux Mint Wireless doesn't connect

  - by guisantogui

  I'm having a great problem, I've installed Linux mint debian edition (LMDE), and following this tutorial http://community.linuxmint.com/tutorial/view/161 I did installed the network driver. The available connections appears to me, but when i try to connect to my connection at first time, I got this message: "(4) Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken." And the following tries, I got this another message: "(32) Insufficient privileges." I'm accepting ideas. Thanks. EDIT: The last piece of the logs: Oct 5 00:22:38 gsouza-host ntpd[2116]: peers refreshed Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): bringing up device. Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: nl80211: 'nl80211' generic netlink not found Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: Failed to initialize driver 'nl80211' Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: rfkill: WLAN soft blocked Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> WiFi hardware radio set enabled Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> WiFi now enabled by radio killswitch Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): supplicant interface state: starting -> ready Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <info> (wlan0): supplicant interface state: ready -> inactive Oct 5 00:22:42 gsouza-host NetworkManager[2019]: <warn> Trying to remove a non-existant call id. Oct 5 00:22:42 gsouza-host wpa_supplicant[2055]: rfkill: WLAN unblocked Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: Joining mDNS multicast group on interface wlan0.IPv6 with address fe80::7ae4:ff:fe4a:13a9. Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: New relevant interface wlan0.IPv6 for mDNS. Oct 5 00:22:44 gsouza-host avahi-daemon[1827]: Registering new address record for fe80::7ae4:ff:fe4a:13a9 on wlan0.*. Oct 5 00:22:46 gsouza-host ntpd[2116]: Listen normally on 7 wlan0 fe80::7ae4:ff:fe4a:13a9 UDP 123 Oct 5 00:22:46 gsouza-host ntpd[2116]: peers refreshed

  Read the article

• Linksys WiFi usb dongle and linux woes

  - by MrStatic

  I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

  Read the article

• Easiest linux distro creation

  - by QAH

  Hello everyone! I have been trying to create my own customized distro of linux (preferably some kind of Debian system like Debian, Ubuntu, Knoppix, etc). I want to make it specifically for playing games. This is just a pet project for me and while I know linux pretty well (bash, gcc, g++, gdb, etc), I'm not that great with knowing the kernel. So that puts making my own distro from scratch out of the question. I went on to trying to create remasters of Knoppix and it worked for me but it was a very long process since knoppix is meant to be a live CD and I was running it in VirtualBox. So what is the easiest and fastest method of making your own distro? Also, can I install ubuntu or some kind of linux to a computer make changes to it, and then make a distro off of that installation? Please help me with this, Thanks

  Read the article

• Linux memory fragmentation

  - by Raghu

  Hi all, Is there a way to detect memory fragmentation on linux ? This is because on some long running servers I have noticed performance degradation and only after I restart process I see better performance. I noticed it more when using linux huge page support -- are huge pages in linux more prone to fragmentation ? I have looked at /proc/buddyinfo in particular. I want to know whether there are any better ways(not just CLI commands per se, any program or theoretical background would do) to look at it.

  Read the article

• mini linux to use dd and access HD and/or USB

  - by acidzombie24

  I was thinking about something. I want to install a 7gb partition and store 2 compress disk image and install linux to it. I want it to be light. What i would like to do is hide the grub loader (or anything) and if i want to reformat my PC press a certain key on startup. Which will then load the linux OS and then i can use dd to restore the partition i want I plan to use windows XP and windows 7 as my main OS and virtualize anything else i need (vista, dummy XP for testing, multiple linux distos, etc). Bonus points if you can tell me how to hide the partition in windows so XP and 7 cant touch it

  Read the article

• __modver_version_show undefined error when building linux kernel 3.0.4 version

  - by Jie Liu

  I tried to build the linux kernel 3.0.4 on ubuntu 11.10 in virtualbox. Here are my steps: Download the source code tar xjvf linux-source-3.0.0.tar.bz2 cd linux-source-3.0.0 make menuconfig, changed nothing but used the default config and save to .config make Actually I think it should be 3.0.4 because from the Makefile I could see VERSION = 3 PATCHLEVEL = 0 SUBLEVEL = 4 EXTRAVERSION = Then at stage 2 which is to make modules, an error happened: ERROR: "__modver_version_show" [drivers/staging/rts5139/rts5139.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 Perhaps because 3.0.4 is a new release so that I can not find any same problem asked nor any solution to it.

  Read the article

• how to save installs on linux usb

  - by user2508947

  I'm a new person at Linux and am running Linux mint 15 cinnamon from an 8GB sandisk pendrive. I cannot dualboot it with windows until my friend (who is a genius at computers) backs up my windows (apparently). The thing is, I cannot save what I have done on it. for example, if I install drpython on my Linux and switch off my laptop, the next time I switch it on, it's all gone. can anyone tell me how I can save what I have done? Thanks in advance.

  Read the article

• Linux and ClickPads

  - by John

  I just got my Arch / Windows 7 dual-boot setup running... except for one thing. I have an HP dv6-3127dx laptop, which is an issue when it comes to Linux because it does not have a traditional touchpad, but a "ClickPad." This means where the left and right buttons exist, it is also sensitive to moving the pointer. The issue comes in when I try to steady the mouse with one finger, while clicking the left click with another, because the mouse freaks out. It's also an issue because it's not recognizing the right click whatsoever. I am currently using the default Synaptics drivers downloaded from pacman on Arch Linux, running Linux v2.6.36. EDIT: The question of course is, how can I fix this?

  Read the article

• What is the sequence followed by the Linux kernel to configure a device?

  - by Jaime Soriano

  As I understood after reading the chapter related to The Linux Device Model in the Linux Device Drivers 3rd Edition, when a new device is configured, the kernel follows more or less this sequence: The Device is registered in the driver core (device_register(), what includes device initialization) A kobject is registered in the device model It provokes a hotplug event Bus and drivers are checked to see which one matches with the device Probe Device is binded to the driver My main doubt is, in step 1, when is device_register() called and what info should be yet in the device struct? Is it called by the bus to which the device is connected? Any example in the code? Have I misunderstood something? :)

  Read the article

• apt-get install was interrupted

  - by user3475299

  I am new to Ubuntu. I got the following lines after an interrupted apt-get install. Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/apt-auto-removal 3.13.0-29-generic /boot/vmlinuz-3.13.0-29-generic run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.13.0-29-generic /boot/vmlinuz-3.13.0-29-generic update-initramfs: Generating /boot/initrd.img-3.13.0-29-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.13.0-29-generic /boot/vmlinuz-3.13.0-29-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.13.0-29-generic /boot/vmlinuz-3.13.0-29-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.13.0-29-generic /boot/vmlinuz-3.13.0-29-generic /usr/sbin/grub-mkconfig: 14: /etc/default/grub: nouveau.modeset=0: not found run-parts: /etc/kernel/postinst.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postinst.d at /var/lib/dpkg/info/linux-image-3.13.0-29-generic.postinst line 1025. No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already dpkg: error processing package linux-image-3.13.0-29-generic (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of linux-image-extra-3.13.0-29-generic: linux-image-extra-3.13.0-29-generic depends on linux-image-3.13.0-29-generic; however: Package linux-image-3.13.0-29-generic is not configured yet. dpkg: error processing package linux-image-extra-3.13.0-29-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-image-generic: linux-image-generic depends on linux-image-3.13.0-29-generic; however: Package linux-image-3.13.0-29-generic is not configured yet. linux-image-generic depends on linux-image-extra-3.13.0-29-generic; however: Package linux-image-extra-3.13.0-29-generic is not configured yet. dpkg: error processing package linux-image-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-generic: linux-generic depends on linux-image-generic (= 3.13.0.29.35); however: Package linux-image-generic is not configured yet. dpkg: error processing package linux-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-image-extra-3.13.0-27-generic: linux-image-extra-3.13.0-27-generic depends on linux-image-3.13.0-27-generic; however: Package linux-image-3.13.0-27-generic is not configured yet. dpkg: error processing package linux-image-extra-3.13.0-27-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-signed-image-3.13.0-29-generic: linux-signed-image-3.13.0-29-generic depends on linux-image-3.13.0-29-generic (= 3.13.0-29.53); however: Package linux-image-3.13.0-29-generic is not configured yet. linux-signed-image-3.13.0-29-generic depends on linux-image-extra-3.13.0-29-generic (= 3.13.0-29.53); however: Package linux-image-extra-3.13.0-29-generic is not configured yet. dpkg: error processing package linux-signed-image-3.13.0-29-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-signed-image-generic: linux-signed-image-generic depends on linux-signed-image-3.13.0-29-generic; however: Package linux-signed-image-3.13.0-29-generic is not configured yet. dpkg: error processing package linux-signed-image-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-signed-generic: linux-signed-generic depends on linux-signed-image-generic (= 3.13.0.29.35); however: Package linux-signed-image-generic is not configured yet. dpkg: error processing package linux-signed-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-signed-image-3.13.0-27-generic: linux-signed-image-3.13.0-27-generic depends on linux-image-3.13.0-27-generic (= 3.13.0-27.50); however: Package linux-image-3.13.0-27-generic is not configured yet. linux-signed-image-3.13.0-27-generic depends on linux-image-extra-3.13.0-27-generic (= 3.13.0-27.50); however: Package linux-image-extra-3.13.0-27-generic is not configured yet. dpkg: error processing package linux-signed-image-3.13.0-27-generic (--configure): dependency problems - leaving unconfigured Setting up libxkbcommon-x11-0:amd64 (0.4.1-0ubuntu1) ... Setting up libqt5gui5:amd64 (5.2.1+dfsg-1ubuntu14.2) ... Processing triggers for libc-bin (2.19-0ubuntu6) ... Errors were encountered while processing: linux-image-3.13.0-27-generic linux-image-3.13.0-29-generic linux-image-extra-3.13.0-29-generic linux-image-generic linux-generic linux-image-extra-3.13.0-27-generic linux-signed-image-3.13.0-29-generic linux-signed-image-generic linux-signed-generic linux-signed-image-3.13.0-27-generic E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >