Search Results

Search found 528 results on 22 pages for 'netmask'.

Page 10/22 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Can't connect to local IP address on OSX

  - by Alex Worden

  I'm trying to connect to a webserver that's running on my mac OSX 1.6. I'm able to connect to it locally using http://127.0.0.1:8888/myapp but when I attempt to connect to it using my machine's local IP address (http://192.168.1.15:8888/myapp IP shown below) from the same machine (or another on the network) I cannot connect. I can ping the LAN IP address. I've tried adding IP forwarding to my router for port 8888 but it didn't help. I've checked and the OSX firewall is disabled Can anyone suggest what else is blocking the connection? Here's what I get when I run ifconfig: ~ :ifconfig lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:e8:16:4d media: autoselect status: inactive supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::21e:c2ff:febf:4809%en1 prefixlen 64 scopeid 0x5 inet 192.168.1.15 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1e:c2:bf:48:09 media: autoselect status: active supported media: autoselect fw0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:1f:5b:ff:fe:2b:b3:3c media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en5: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500 ether 00:1e:c2:8e:0f:45 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> en2: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:1c:42:00:00:00 media: autoselect status: inactive supported media: autoselect en3: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:1c:42:00:00:01 media: autoselect status: inactive supported media: autoselect

  Read the article

• How to parse IP addresses with perl?

  - by Andrey Zentavr

  Hello! I have list of IPs: 238.51.208.96/28 238.51.209.180-199 238.51.209.100-109 238.51.213.2-254 ... How can I easily parse them? I need first and last IP from range. For First line I can use Net::Netmask CPAN module, but what can I do with others lines?

  Read the article

• How can I parse IP addresses and address ranges with perl?

  - by Andrey Zentavr

  I have list of IPs: 238.51.208.96/28 238.51.209.180-199 238.51.209.100-109 238.51.213.2-254 ... How can I easily parse them? I need first and last IP from range. For the first line I can use Net::Netmask CPAN module, but what can I do with others lines?

  Read the article

• Ubuntu 9.10 and Squid 2.7 Transparent Proxy TCP_DENIED

  - by user38400

  Hi, We've spent the last two days trying to get squid 2.7 to work with ubuntu 9.10. The computer running ubuntu has two network interfaces: eth0 and eth1 with dhcp running on eth1. Both interfaces have static ip's, eth0 is connected to the Internet and eth1 is connected to our LAN. We have followed literally dozens of different tutorials with no success. The tutorial here was the last one we did that actually got us some sort of results: http://www.basicconfig.com/linuxnetwork/setup_ubuntu_squid_proxy_server_beginner_guide. When we try to access a site like seriouswheels.com from the LAN we get the following message on the client machine: ERROR The requested URL could not be retrieved Invalid Request error was encountered while trying to process the request: GET / HTTP/1.1 Host: www.seriouswheels.com Connection: keep-alive User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.11 Safari/532.9 Cache-Control: max-age=0 Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,/;q=0.5 Accept-Encoding: gzip,deflate,sdch Cookie: __utmz=88947353.1269218405.1.1.utmccn=(direct)|utmcsr=(direct)|utmcmd=(none); __qca=P0-1052556952-1269218405250; __utma=88947353.1027590811.1269218405.1269218405.1269218405.1; __qseg=Q_D Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Some possible problems are: Missing or unknown request method. Missing URL. Missing HTTP Identifier (HTTP/1.0). Request is too large. Content-Length missing for POST or PUT requests. Illegal character in hostname; underscores are not allowed. Your cache administrator is webmaster. Below are all the configuration files: /etc/squid/squid.conf, /etc/network/if-up.d/00-firewall, /etc/network/interfaces, /var/log/squid/access.log. Something somewhere is wrong but we cannot figure out where. Our end goal for all of this is the superimpose content onto every page that a client requests on the LAN. We've been told that squid is the way to do this but at this point in the game we are just trying to get squid setup correctly as our proxy. Thanks in advance. squid.conf acl all src all acl manager proto cache_object acl localhost src 127.0.0.1/32 acl to_localhost dst 127.0.0.0/8 acl localnet src 192.168.0.0/24 acl SSL_ports port 443 # https acl SSL_ports port 563 # snews acl SSL_ports port 873 # rsync acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl Safe_ports port 631 # cups acl Safe_ports port 873 # rsync acl Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access allow localnet http_access deny all icp_access allow localnet icp_access deny all http_port 3128 hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid/cache1 1000 16 256 access_log /var/log/squid/access.log squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern (Release|Package(.gz)*)$ 0 20% 2880 refresh_pattern . 0 20% 4320 acl shoutcast rep_header X-HTTP09-First-Line ^ICY.[0-9] upgrade_http0.9 deny shoutcast acl apache rep_header Server ^Apache broken_vary_encoding allow apache extension_methods REPORT MERGE MKACTIVITY CHECKOUT cache_mgr webmaster cache_effective_user proxy cache_effective_group proxy hosts_file /etc/hosts coredump_dir /var/spool/squid access.log 1269243042.740 0 192.168.1.11 TCP_DENIED/400 2576 GET NONE:// - NONE/- text/html 00-firewall iptables -F iptables -t nat -F iptables -t mangle -F iptables -X echo 1 | tee /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -j MASQUERADE iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-port 3128 networking auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 142.104.109.179 netmask 255.255.224.0 gateway 142.104.127.254 auto eth1 iface eth1 inet static address 192.168.1.100 netmask 255.255.255.0

  Read the article

• Mpd as pppoe server with authorisation by freeradius2

  - by Korjavin Ivan

  I install freeradius2, add to raddb/users: test Cleartext-Password := "test1" Service-Type = Framed-User, Framed-Protocol = PPP, Framed-IP-Address = 10.36.0.2, Framed-IP-Netmask = 255.255.255.0, start radiusd, and check auth: radtest test test1 127.0.0.1 1002 testing123 Sending Access-Request of id 199 to 127.0.0.1 port 1812 User-Name = "test" User-Password = "test1" NAS-IP-Address = 127.0.0.1 NAS-Port = 1002 Message-Authenticator = 0x00000000000000000000000000000000 rad_recv: Access-Accept packet from host 127.0.0.1 port 1812, id=199, length=44 Service-Type = Framed-User Framed-Protocol = PPP Framed-IP-Address = 10.36.0.2 Framed-IP-Netmask = 255.255.255.0 Works fine. Next step. Add to mpd.conf: radius: set auth disable internal set auth max-logins 1 CI set auth enable radius-auth set radius timeout 90 set radius retries 2 set radius server 127.0.0.1 testing123 1812 1813 set radius me 127.0.0.1 create link template L pppoe set link action bundle B set link max-children 1000 set link no multilink set link no shortseq set link no pap chap-md5 chap-msv1 chap-msv2 set link enable chap set pppoe acname Internet load radius create link template em1 L set pppoe iface em1 set link enable incoming And trying to connect, auth failed, here is mpd log: mpd: [em1-2] LCP: auth: peer wants nothing, I want CHAP mpd: [em1-2] CHAP: sending CHALLENGE #1 len: 21 mpd: [em1-2] LCP: LayerUp mpd: [em1-2] CHAP: rec'd RESPONSE #1 len: 58 mpd: [em1-2] Name: "test" mpd: [em1-2] AUTH: Trying RADIUS mpd: [em1-2] RADIUS: Authenticating user 'test' mpd: [em1-2] RADIUS: Rec'd RAD_ACCESS_REJECT for user 'test' mpd: [em1-2] AUTH: RADIUS returned: failed mpd: [em1-2] AUTH: ran out of backends mpd: [em1-2] CHAP: Auth return status: failed mpd: [em1-2] CHAP: Reply message: ^AE=691 R=1 mpd: [em1-2] CHAP: sending FAILURE #1 len: 14 mpd: [em1-2] LCP: authorization failed Then i start freeradius as radiusd -fX, and get this log: rad_recv: Access-Request packet from host 127.0.0.1 port 46400, id=223, length=282 NAS-Identifier = "rubin.svyaz-nt.ru" NAS-IP-Address = 127.0.0.1 Message-Authenticator = 0x14d36639bed8074ec2988118125367ea Acct-Session-Id = "815965-em1-2" NAS-Port = 2 NAS-Port-Type = Ethernet Service-Type = Framed-User Framed-Protocol = PPP Calling-Station-Id = "00e05290b3e3 / 00:e0:52:90:b3:e3 / em1" NAS-Port-Id = "em1" Vendor-12341-Attr-12 = 0x656d312d32 Tunnel-Medium-Type:0 = IEEE-802 Tunnel-Client-Endpoint:0 = "00:e0:52:90:b3:e3" User-Name = "test" MS-CHAP-Challenge = 0xbb1e68d5bbc30f228725a133877de83e MS-CHAP2-Response = 0x010088746ae65b68e435e9d045ad6f9569b60000000000000000b56991b4f20704cb6c68e5982eec5e98a7f4b470c109c1b9 # Executing section authorize from file /usr/local/etc/raddb/sites-enabled/default +- entering group authorize {...} ++[preprocess] returns ok ++[chap] returns noop [mschap] Found MS-CHAP attributes. Setting 'Auth-Type = mschap' ++[mschap] returns ok [eap] No EAP-Message, not doing EAP ++[eap] returns noop [files] users: Matched entry DEFAULT at line 172 ++[files] returns ok Found Auth-Type = MSCHAP # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group MS-CHAP {...} [mschap] No Cleartext-Password configured. Cannot create LM-Password. [mschap] No Cleartext-Password configured. Cannot create NT-Password. [mschap] Creating challenge hash with username: test [mschap] Client is using MS-CHAPv2 for test, we need NT-Password [mschap] FAILED: No NT/LM-Password. Cannot perform authentication. [mschap] FAILED: MS-CHAP2-Response is incorrect ++[mschap] returns reject Failed to authenticate the user. Login incorrect: [test] (from client localhost port 2 cli 00e05290b3e3 / 00:e0:52:90:b3:e3 / em1) Using Post-Auth-Type REJECT # Executing group from file /usr/local/etc/raddb/sites-enabled/default +- entering group REJECT {...} [attr_filter.access_reject] expand: %{User-Name} -> test attr_filter: Matched entry DEFAULT at line 11 ++[attr_filter.access_reject] returns updated Delaying reject of request 2 for 1 seconds Going to the next request Waking up in 0.9 seconds. Sending delayed reject for request 2 Sending Access-Reject of id 223 to 127.0.0.1 port 46400 MS-CHAP-Error = "\001E=691 R=1" Why i have error "[mschap] No Cleartext-Password configured. Cannot create LM-Password." ? I define cleartext-password in users. I check raddb/sites-enabled/default authorize { chap mschap eap { ok = return } files } looks ok for me. Whats wrong with mpd/chap/radius ?

  Read the article

• Dhcpd Daemon is trying to lease itself?

  - by tommieb75

  I have a Slackware Linux 13.0 box with two interfaces, eth0 and eth1. I have set this box up to be on the 192.168.1.0/24 network, with subnet mask of 255.255.255.0. I am trying to run a dhcpd server on this box to service two interfaces above, so I subnetted the 192.168.1.0/24 network into two subnets. For eth0 192.168.1.1, subnet mask 255.255.255.128, broadcast mask 192.168.1.127. For eth1 192.168.1.129, subnet mask 255.255.255.128, broadcast mask 192.168.1.255. Both the interfaces are assigned manually. eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.1 Bcast:192.168.1.127 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:39 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1404 (1.3 KiB) Interrupt:11 Base address:0x8000 Memory:faffc000-faffcfff eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.128 Bcast:192.168.1.255 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10003 errors:0 dropped:0 overruns:0 frame:0 TX packets:13286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1589229 (1.5 MiB) TX bytes:9900005 (9.4 MiB) Interrupt:11 Here is the dhcpd.conf set up authoritative; ddns-update-style interim; ignore client-updates; subnet 192.168.1.0 netmask 255.255.255.128 { range 192.168.1.2 192.168.1.126; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.127; option subnet-mask 255.255.255.128; } subnet 192.168.1.128 netmask 255.255.255.128 { range 192.168.1.129 192.168.1.254; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.255; option subnet-mask 255.255.255.128; } This is what is showing in the log Apr 10 18:09:58 inspiron8600 dhcpd: DHCPDISCOVER from 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:09:58 inspiron8600 dhcpd: DHCPOFFER on 192.168.1.131 to 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:10:01 inspiron8600 dhcpcd[3832]: eth1: adding IP address 169.254.153.6/16 This is happening spuriously, and the log gets filled up with nonsense..so my question is this: How do I stop this from happening? And why would it be trying to give itself a lease? I am sure I have missed something but cannot see it and would appreciate a pair of eyes from the community to spot the obvious flaw!

  Read the article

• NIC Bonding/balance-rr with Dell PowerConnect 5324

  - by Branden Martin

  I'm trying to get NIC bonding to work with balance-rr so that three NIC ports are combined, so that instead of getting 1 Gbps we get 3 Gbps. We are doing this on two servers connected to the same switch. However, we're only getting the speed of one physical link. We are using 1 Dell PowerConnect 5324, SW version 2.0.1.3, Boot version 1.0.2.02, HW version 00.00.02. Both servers are CentOS 5.9 (Final) running OnApp Hypervisor (CloudBoot) Server 1 is using ports g5-g7 in port-channel 1. Server 2 is using ports g9-g11 in port-channel 2. Switch show interface status Port Type Duplex Speed Neg ctrl State Pressure Mode -------- ------------ ------ ----- -------- ---- ----------- -------- ------- g1 1G-Copper -- -- -- -- Down -- -- g2 1G-Copper Full 1000 Enabled Off Up Disabled Off g3 1G-Copper -- -- -- -- Down -- -- g4 1G-Copper -- -- -- -- Down -- -- g5 1G-Copper Full 1000 Enabled Off Up Disabled Off g6 1G-Copper Full 1000 Enabled Off Up Disabled Off g7 1G-Copper Full 1000 Enabled Off Up Disabled On g8 1G-Copper Full 1000 Enabled Off Up Disabled Off g9 1G-Copper Full 1000 Enabled Off Up Disabled On g10 1G-Copper Full 1000 Enabled Off Up Disabled On g11 1G-Copper Full 1000 Enabled Off Up Disabled Off g12 1G-Copper Full 1000 Enabled Off Up Disabled On g13 1G-Copper -- -- -- -- Down -- -- g14 1G-Copper -- -- -- -- Down -- -- g15 1G-Copper -- -- -- -- Down -- -- g16 1G-Copper -- -- -- -- Down -- -- g17 1G-Copper -- -- -- -- Down -- -- g18 1G-Copper -- -- -- -- Down -- -- g19 1G-Copper -- -- -- -- Down -- -- g20 1G-Copper -- -- -- -- Down -- -- g21 1G-Combo-C -- -- -- -- Down -- -- g22 1G-Combo-C -- -- -- -- Down -- -- g23 1G-Combo-C -- -- -- -- Down -- -- g24 1G-Combo-C Full 100 Enabled Off Up Disabled On Flow Link Ch Type Duplex Speed Neg control State -------- ------- ------ ----- -------- ------- ----------- ch1 1G Full 1000 Enabled Off Up ch2 1G Full 1000 Enabled Off Up ch3 -- -- -- -- -- Not Present ch4 -- -- -- -- -- Not Present ch5 -- -- -- -- -- Not Present ch6 -- -- -- -- -- Not Present ch7 -- -- -- -- -- Not Present ch8 -- -- -- -- -- Not Present Server 1: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:55 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:28:ae USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:28:af USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.52.1 NETMASK=255.255.0.0 GATEWAY=10.200.2.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:55 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:ae Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:28:af Server 2: cat /etc/sysconfig/network-scripts/ifcfg-eth3 DEVICE=eth3 HWADDR=00:1b:21:ac:d5:a7 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth4 DEVICE=eth4 HWADDR=68:05:ca:18:30:30 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-eth5 DEVICE=eth5 HWADDR=68:05:ca:18:30:31 USERCTL=no BOOTPROTO=none ONBOOT=yes MASTER=onappstorebond SLAVE=yes cat /etc/sysconfig/network-scripts/ifcfg-onappstorebond DEVICE=onappstorebond IPADDR=10.200.53.1 NETMASK=255.255.0.0 GATEWAY=10.200.3.254 NETWORK=10.200.0.0 USERCTL=no BOOTPROTO=none ONBOOT=yes cat /proc/net/bonding/onappstorebond Ethernet Channel Bonding Driver: v3.4.0-1 (October 7, 2008) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 00:1b:21:ac:d5:a7 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:30 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 68:05:ca:18:30:31 Here are the results of iperf. ------------------------------------------------------------ Client connecting to 10.200.52.1, TCP port 5001 TCP window size: 27.7 KByte (default) ------------------------------------------------------------ [ 3] local 10.200.3.254 port 53766 connected with 10.200.52.1 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 950 MBytes 794 Mbits/sec

  Read the article

• CentOS 6.2 Bridge Setup for KVM

  - by Gaia

  I'm trying to set up bridged networking with KVM on CentOS 6.2 to no avail. There are plenty of docs and tutorials about it, but they all seem to conflict or don't provide info specific enough to my situation. I just don't get it. I access the host via public IP "xxx.xxx.128.58". All other available IPs (/29) should be bridged and made available to the only KVM guest (running a public facing LAMP stack) that will be setup on this machine. The amazingly unhelpful NOC people assigned the extra IPs to eth1. Is this correct? Should br0 bridge to eth0 or eth1? How do I set this up? Here is the relevant info: eth0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BC inet6 addr: fe80::225:90ff:fe68:febc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:763 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:550811 (537.9 KiB) TX bytes:648 (648.0 b) Memory:fb980000-fba00000 eth1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.58 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 inet6 addr: fe80::225:90ff:fe68:febd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1806 errors:0 dropped:0 overruns:0 frame:0 TX packets:1505 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:133166 (130.0 KiB) TX bytes:106070 (103.5 KiB) Memory:fb900000-fb980000 eth1:0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.59 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.60 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:2 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.61 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:3 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.62 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) virbr0 Link encap:Ethernet HWaddr 52:54:00:62:55:68 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=XXXX.domain.com > brctl show bridge name bridge id STP enabled interfaces br0 8000.00259068febc no eth0 virbr0 8000.525400625568 yes virbr0-nic > ls -fl | grep ifcfg -rw-r--r-- 1 root root 198 Jun 7 10:58 ifcfg-eth0 -rw-r--r--. 1 root root 254 Oct 7 2011 ifcfg-lo -rw-r--r-- 1 root root 77 Jun 6 18:51 ifcfg-eth1-range0 -rw-r--r-- 1 root root 168 Jun 6 18:50 ifcfg-eth1 > cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO="static" BRIDGE="br0" HWADDR="00:25:90:68:FE:BC" IPV6INIT="yes" MTU="1500" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" IPADDR="yyy.yyy.216.131" NETMASK="255.255.255.128" > cat ifcfg-eth1 DEVICE="eth1" HWADDR="00:25:90:68:FE:BD" NM_CONTROLLED="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="xxx.xxx.128.58" NETMASK="255.255.255.248" GATEWAY="xxx.xxx.128.57" > cat ifcfg-eth1-range0 IPADDR_START="xxx.xxx.128.59" IPADDR_END="xxx.xxx.128.62" CLONENUM_START="0" Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xxx.xxx.128.56 * 255.255.255.248 U 0 0 0 eth1 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0 link-local * 255.255.0.0 U 1003 0 0 eth1 default xxx.xxx.128.57 0.0.0.0 UG 0 0 0 eth1

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• Simple Cisco ASA 5505 config issue

  - by Ben Sebborn

  I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

  Read the article

• OpenVPN on Tomato and Vista - can't see my network

  - by Ian

  I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

  Read the article

• Can't communicate between lan ports on openwrt router

  - by ScaryAardvark

  I've got a WBMR-HP-G300H Buffalo Airstation router on which I've installed the lates OpenWRT software. All is working well (ADSL, WIFI etc) except for one niggle. I can't communicate between lan ports. i.e. if I have one computer connected on lan port 1 and I try to ping another computer on lan port 2 then I get "destination unreachable". I can ping both computers from the router itself and can also ping each computer from a seperate laptop connected wirelessly. All computers are in the same subnet range (10.0.0.?/24). I suspect that I may need to configure a vlan on the switch but everytime I try and do this with various google'ed configuration I keep freezing out all lan-ports and I have to revert back using a wirelessly connected laptop. Here's my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ipaddr '10.0.0.1' option _orig_ifname 'eth0 wlan0' option _orig_bridge 'true' option ifname 'eth0' config adsl-device 'adsl' option fwannex 'a' option annex 'a2p' config interface 'wan' option _orig_ifname 'nas0' option _orig_bridge 'false' option proto 'pppoa' option encaps 'vc' option atmdev '0' option vci '38' option vpi '0' option username '?????????????' option password '??????????????' Any help would be warmly received. Here's some more config stuff. root@OpenWrt:~# ifconfig -a br-lan Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:226576 errors:0 dropped:346 overruns:0 frame:0 TX packets:269292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:26771676 (25.5 MiB) TX bytes:183986450 (175.4 MiB) eth0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb0 Link encap:Ethernet HWaddr 36:60:EC:DF:13:A1 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb1 Link encap:Ethernet HWaddr 4A:7B:75:67:54:E0 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:780 errors:0 dropped:0 overruns:0 frame:0 TX packets:780 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:58369 (57.0 KiB) TX bytes:58369 (57.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-24-A5-BD-66-08-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2424 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:320188 (312.6 KiB) TX bytes:0 (0.0 B) pppoa-wan Link encap:Point-to-Point Protocol inet addr:81.136.179.204 P-t-P:81.134.80.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:258894 errors:0 dropped:0 overruns:0 frame:0 TX packets:212976 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:177341656 (169.1 MiB) TX bytes:25192459 (24.0 MiB) wlan0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:204063 errors:0 dropped:0 overruns:0 frame:0 TX packets:245516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:26613140 (25.3 MiB) TX bytes:162799765 (155.2 MiB) root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 8000.0024a5bd6608 no wlan0 eth0 root@OpenWrt:~# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: pvid: 0 link: port:0 link:up speed:1000baseT full-duplex txflow rxflow Port 1: pvid: 0 link: port:1 link:down Port 2: pvid: 0 link: port:2 link:down Port 3: pvid: 0 link: port:3 link:down Port 4: pvid: 0 link: port:4 link:up speed:100baseT full-duplex txflow rxflow auto Port 5: pvid: 0 link: port:5 link:up speed:100baseT full-duplex txflow rxflow auto Regards Mark.

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

  - by Chris Drumgoole

  I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• ASA hairpining: I basicaly want to allow 2 spokes to be able to communicate with each other.

  - by Thirst4Knowledge

  ASA Spoke to Spoke Communication I have been looking at spke to spoke comms or "hairpining" for months and have posted on numerouse forums but to no avail. I have a Hub and spoke network where the HUB is an ASA Firewall version 8.2 * I basicaly want to allow 2 spokes to be able to communicate with each other. I think that I have got the concept of the ASA Config for example: same-security-traffic permit intra-interface access-list HQ-LAN extended permit ip ASA-LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list HQ-LAN extended permit ip 192.168.99.0 255.255.255.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 access-list no-nat extended permit ip 192.168.99.0 255.255.255.0 HQ-LAN 255.255.255.0 I think my problem may be that the other spokes are not CIsco Firewalls and I need to work out how to do the alternative setups. I want to at least make sure that my firewall etup is correct then I can move onto the other spokes here is my config: Hostname ASA domain-name mydomain.com names ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 1.1.1.246 255.255.255.224 ! interface Ethernet0/1 speed 100 duplex full nameif inside security-level 100 ip address 192.168.240.33 255.255.255.224 ! interface Ethernet0/2 description DMZ VLAN-253 speed 100 duplex full nameif DMZ security-level 50 ip address 192.168.254.1 255.255.255.0 ! interface Ethernet0/3 no nameif no security-level no ip address ! boot system disk0:/asa821-k8.bin ftp mode passive clock timezone GMT/BST 0 dns server-group DefaultDNS domain-name mydomain.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network ASA_LAN_Plus_HQ_LAN network-object ASA_LAN 255.255.248.0 network-object HQ-LAN 255.255.255.0 access-list outside_acl remark Exchange web access-list outside_acl extended permit tcp any host MS-Exchange_server-NAT eq https access-list outside_acl remark PPTP Encapsulation access-list outside_acl extended permit gre any host MS-ISA-Server-NAT access-list outside_acl remark PPTP access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq pptp access-list outside_acl remark Intra Http access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq www access-list outside_acl remark Intra Https access-list outside_acl extended permit tcp any host MS-ISA-Server-NAT eq https access-list outside_acl remark SSL Server-Https 443 access-list outside_acl remark Https 8443(Open VPN Custom port for SSLVPN client downlaod) access-list outside_acl remark FTP 20 access-list outside_acl remark Http access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT object-group DM_INLINE_TCP_1 access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq 8443 access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq www access-list outside_acl remark For secure remote Managment-SSH access-list outside_acl extended permit tcp any host OpenVPN-Srvr-NAT eq ssh access-list outside_acl extended permit ip Genimage_Anyconnect 255.255.255.0 ASA_LAN 255.255.248.0 access-list ASP-Live remark Live ASP access-list ASP-Live extended permit ip ASA_LAN 255.255.248.0 192.168.60.0 255.255.255.0 access-list Bo remark Bo access-list Bo extended permit ip ASA_LAN 255.255.248.0 192.168.169.0 255.255.255.0 access-list Bill remark Bill access-list Bill extended permit ip ASA_LAN 255.255.248.0 Bill.15 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 Bill.5 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.149.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.160.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.165.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.144.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.140.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.152.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.153.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.163.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.157.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.167.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.156.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 North-Office-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.161.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.143.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.137.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.159.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.169.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.150.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.162.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.166.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.168.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.174.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.127.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.173.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.175.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.176.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.100.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 192.168.99.0 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 10.10.10.0 255.255.255.0 access-list no-nat extended permit ip host 192.168.240.34 Cisco-admin-LAN 255.255.255.0 access-list no-nat extended permit ip ASA_LAN 255.255.248.0 Genimage_Anyconnect 255.255.255.0 access-list no-nat extended permit ip host Tunnel-DC host HQ-SDSL-Peer access-list no-nat extended permit ip HQ-LAN 255.255.255.0 North-Office-LAN 255.255.255.0 access-list no-nat extended permit ip North-Office-LAN 255.255.255.0 HQ-LAN 255.255.255.0 access-list Car remark Car access-list Car extended permit ip ASA_LAN 255.255.248.0 192.168.165.0 255.255.255.0 access-list Che remark Che access-list Che extended permit ip ASA_LAN 255.255.248.0 192.168.144.0 255.255.255.0 access-list Chi remark Chi access-list Chi extended permit ip ASA_LAN 255.255.248.0 192.168.140.0 255.255.255.0 access-list Cla remark Cla access-list Cla extended permit ip ASA_LAN 255.255.248.0 192.168.152.0 255.255.255.0 access-list Eas remark Eas access-list Eas extended permit ip ASA_LAN 255.255.248.0 192.168.149.0 255.255.255.0 access-list Ess remark Ess access-list Ess extended permit ip ASA_LAN 255.255.248.0 192.168.153.0 255.255.255.0 access-list Gat remark Gat access-list Gat extended permit ip ASA_LAN 255.255.248.0 192.168.163.0 255.255.255.0 access-list Hud remark Hud access-list Hud extended permit ip ASA_LAN 255.255.248.0 192.168.157.0 255.255.255.0 access-list Ilk remark Ilk access-list Ilk extended permit ip ASA_LAN 255.255.248.0 192.168.167.0 255.255.255.0 access-list Ken remark Ken access-list Ken extended permit ip ASA_LAN 255.255.248.0 192.168.156.0 255.255.255.0 access-list North-Office remark North-Office access-list North-Office extended permit ip ASA_LAN 255.255.248.0 North-Office-LAN 255.255.255.0 access-list inside_acl remark Inside_ad access-list inside_acl extended permit ip any any access-list Old_HQ remark Old_HQ access-list Old_HQ extended permit ip ASA_LAN 255.255.248.0 HQ-LAN 255.255.255.0 access-list Old_HQ extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 access-list She remark She access-list She extended permit ip ASA_LAN 255.255.248.0 192.168.150.0 255.255.255.0 access-list Lit remark Lit access-list Lit extended permit ip ASA_LAN 255.255.248.0 192.168.143.0 255.255.255.0 access-list Mid remark Mid access-list Mid extended permit ip ASA_LAN 255.255.248.0 192.168.137.0 255.255.255.0 access-list Spi remark Spi access-list Spi extended permit ip ASA_LAN 255.255.248.0 192.168.162.0 255.255.255.0 access-list Tor remark Tor access-list Tor extended permit ip ASA_LAN 255.255.248.0 192.168.166.0 255.255.255.0 access-list Tra remark Tra access-list Tra extended permit ip ASA_LAN 255.255.248.0 192.168.168.0 255.255.255.0 access-list Tru remark Tru access-list Tru extended permit ip ASA_LAN 255.255.248.0 192.168.174.0 255.255.255.0 access-list Yo remark Yo access-list Yo extended permit ip ASA_LAN 255.255.248.0 192.168.127.0 255.255.255.0 access-list Nor remark Nor access-list Nor extended permit ip ASA_LAN 255.255.248.0 192.168.159.0 255.255.255.0 access-list Nor extended permit ip ASA_LAN 255.255.248.0 192.168.173.0 255.255.255.0 inactive access-list ST remark ST access-list ST extended permit ip ASA_LAN 255.255.248.0 192.168.175.0 255.255.255.0 access-list Le remark Le access-list Le extended permit ip ASA_LAN 255.255.248.0 192.168.161.0 255.255.255.0 access-list DMZ-ACL remark DMZ access-list DMZ-ACL extended permit ip host OpenVPN-Srvr any access-list no-nat-dmz remark DMZ -No Nat access-list no-nat-dmz extended permit ip 192.168.250.0 255.255.255.0 HQ-LAN 255.255.255.0 access-list Split_Tunnel_List remark ASA-LAN access-list Split_Tunnel_List standard permit ASA_LAN 255.255.248.0 access-list Split_Tunnel_List standard permit Genimage_Anyconnect 255.255.255.0 access-list outside_cryptomap_30 remark Po access-list outside_cryptomap_30 extended permit ip ASA_LAN 255.255.248.0 Po 255.255.255.0 access-list outside_cryptomap_24 extended permit ip ASA_LAN 255.255.248.0 192.168.100.0 255.255.255.0 access-list outside_cryptomap_16 extended permit ip ASA_LAN 255.255.248.0 192.168.99.0 255.255.255.0 access-list outside_cryptomap_34 extended permit ip ASA_LAN 255.255.248.0 10.10.10.0 255.255.255.0 access-list outside_31_cryptomap extended permit ip host 192.168.240.34 Cisco-admin-LAN 255.255.255.0 access-list outside_32_cryptomap extended permit ip host Tunnel-DC host HQ-SDSL-Peer access-list Genimage_VPN_Any_connect_pix_client remark Genimage "Any Connect" VPN access-list Genimage_VPN_Any_connect_pix_client standard permit Genimage_Anyconnect 255.255.255.0 access-list Split-Tunnel-ACL standard permit ASA_LAN 255.255.248.0 access-list nonat extended permit ip HQ-LAN 255.255.255.0 192.168.99.0 255.255.255.0 pager lines 24 logging enable logging timestamp logging console notifications logging monitor notifications logging buffered warnings logging asdm informational no logging message 106015 no logging message 313001 no logging message 313008 no logging message 106023 no logging message 710003 no logging message 106100 no logging message 302015 no logging message 302014 no logging message 302013 no logging message 302018 no logging message 302017 no logging message 302016 no logging message 302021 no logging message 302020 flow-export destination inside MS-ISA-Server 2055 flow-export destination outside 192.168.130.126 2055 flow-export template timeout-rate 1 flow-export delay flow-create 15 mtu outside 1500 mtu inside 1500 mtu DMZ 1500 mtu management 1500 ip local pool RAS-VPN 10.0.0.1.1-10.0.0.1.254 mask 255.255.255.255 icmp unreachable rate-limit 1 burst-size 1 icmp permit any unreachable outside icmp permit any echo outside icmp permit any echo-reply outside icmp permit any outside icmp permit any echo inside icmp permit any echo-reply inside icmp permit any echo DMZ icmp permit any echo-reply DMZ asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 nat-control global (outside) 1 interface global (inside) 1 interface nat (inside) 0 access-list no-nat nat (inside) 1 0.0.0.0 0.0.0.0 nat (DMZ) 0 access-list no-nat-dmz static (inside,outside) MS-ISA-Server-NAT MS-ISA-Server netmask 255.255.255.255 static (DMZ,outside) OpenVPN-Srvr-NAT OpenVPN-Srvr netmask 255.255.255.255 static (inside,outside) MS-Exchange_server-NAT MS-Exchange_server netmask 255.255.255.255 access-group outside_acl in interface outside access-group inside_acl in interface inside access-group DMZ-ACL in interface DMZ route outside 0.0.0.0 0.0.0.0 1.1.1.225 1 route inside 10.10.10.0 255.255.255.0 192.168.240.34 1 route outside Genimage_Anyconnect 255.255.255.0 1.1.1.225 1 route inside Open-VPN 255.255.248.0 OpenVPN-Srvr 1 route inside HQledon-Voice-LAN 255.255.255.0 192.168.240.34 1 route outside Bill 255.255.255.0 1.1.1.225 1 route outside Yo 255.255.255.0 1.1.1.225 1 route inside 192.168.129.0 255.255.255.0 192.168.240.34 1 route outside HQ-LAN 255.255.255.0 1.1.1.225 1 route outside Mid 255.255.255.0 1.1.1.225 1 route outside 192.168.140.0 255.255.255.0 1.1.1.225 1 route outside 192.168.143.0 255.255.255.0 1.1.1.225 1 route outside 192.168.144.0 255.255.255.0 1.1.1.225 1 route outside 192.168.149.0 255.255.255.0 1.1.1.225 1 route outside 192.168.152.0 255.255.255.0 1.1.1.225 1 route outside 192.168.153.0 255.255.255.0 1.1.1.225 1 route outside North-Office-LAN 255.255.255.0 1.1.1.225 1 route outside 192.168.156.0 255.255.255.0 1.1.1.225 1 route outside 192.168.157.0 255.255.255.0 1.1.1.225 1 route outside 192.168.159.0 255.255.255.0 1.1.1.225 1 route outside 192.168.160.0 255.255.255.0 1.1.1.225 1 route outside 192.168.161.0 255.255.255.0 1.1.1.225 1 route outside 192.168.162.0 255.255.255.0 1.1.1.225 1 route outside 192.168.163.0 255.255.255.0 1.1.1.225 1 route outside 192.168.165.0 255.255.255.0 1.1.1.225 1 route outside 192.168.166.0 255.255.255.0 1.1.1.225 1 route outside 192.168.167.0 255.255.255.0 1.1.1.225 1 route outside 192.168.168.0 255.255.255.0 1.1.1.225 1 route outside 192.168.173.0 255.255.255.0 1.1.1.225 1 route outside 192.168.174.0 255.255.255.0 1.1.1.225 1 route outside 192.168.175.0 255.255.255.0 1.1.1.225 1 route outside 192.168.99.0 255.255.255.0 1.1.1.225 1 route inside ASA_LAN 255.255.255.0 192.168.240.34 1 route inside 192.168.124.0 255.255.255.0 192.168.240.34 1 route inside 192.168.50.0 255.255.255.0 192.168.240.34 1 route inside 192.168.51.0 255.255.255.128 192.168.240.34 1 route inside 192.168.240.0 255.255.255.224 192.168.240.34 1 route inside 192.168.240.164 255.255.255.224 192.168.240.34 1 route inside 192.168.240.196 255.255.255.224 192.168.240.34 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server vpn protocol radius max-failed-attempts 5 aaa-server vpn (inside) host 192.168.X.2 timeout 60 key a5a53r3t authentication-port 1812 radius-common-pw a5a53r3t aaa authentication ssh console LOCAL aaa authentication http console LOCAL http server enable http 0.0.0.0 0.0.0.0 inside http 1.1.1.2 255.255.255.255 outside http 1.1.1.234 255.255.255.255 outside http 0.0.0.0 0.0.0.0 management http 1.1.100.198 255.255.255.255 outside http 0.0.0.0 0.0.0.0 outside crypto map FW_Outside_map 1 match address Bill crypto map FW_Outside_map 1 set peer x.x.x.121 crypto map FW_Outside_map 1 set transform-set SECURE crypto map FW_Outside_map 2 match address Bo crypto map FW_Outside_map 2 set peer x.x.x.202 crypto map FW_Outside_map 2 set transform-set SECURE crypto map FW_Outside_map 3 match address ASP-Live crypto map FW_Outside_map 3 set peer x.x.x.113 crypto map FW_Outside_map 3 set transform-set SECURE crypto map FW_Outside_map 4 match address Car crypto map FW_Outside_map 4 set peer x.x.x.205 crypto map FW_Outside_map 4 set transform-set SECURE crypto map FW_Outside_map 5 match address Old_HQ crypto map FW_Outside_map 5 set peer x.x.x.2 crypto map FW_Outside_map 5 set transform-set SECURE WG crypto map FW_Outside_map 6 match address Che crypto map FW_Outside_map 6 set peer x.x.x.204 crypto map FW_Outside_map 6 set transform-set SECURE crypto map FW_Outside_map 7 match address Chi crypto map FW_Outside_map 7 set peer x.x.x.212 crypto map FW_Outside_map 7 set transform-set SECURE crypto map FW_Outside_map 8 match address Cla crypto map FW_Outside_map 8 set peer x.x.x.215 crypto map FW_Outside_map 8 set transform-set SECURE crypto map FW_Outside_map 9 match address Eas crypto map FW_Outside_map 9 set peer x.x.x.247 crypto map FW_Outside_map 9 set transform-set SECURE crypto map FW_Outside_map 10 match address Ess crypto map FW_Outside_map 10 set peer x.x.x.170 crypto map FW_Outside_map 10 set transform-set SECURE crypto map FW_Outside_map 11 match address Hud crypto map FW_Outside_map 11 set peer x.x.x.8 crypto map FW_Outside_map 11 set transform-set SECURE crypto map FW_Outside_map 12 match address Gat crypto map FW_Outside_map 12 set peer x.x.x.212 crypto map FW_Outside_map 12 set transform-set SECURE crypto map FW_Outside_map 13 match address Ken crypto map FW_Outside_map 13 set peer x.x.x.230 crypto map FW_Outside_map 13 set transform-set SECURE crypto map FW_Outside_map 14 match address She crypto map FW_Outside_map 14 set peer x.x.x.24 crypto map FW_Outside_map 14 set transform-set SECURE crypto map FW_Outside_map 15 match address North-Office crypto map FW_Outside_map 15 set peer x.x.x.94 crypto map FW_Outside_map 15 set transform-set SECURE crypto map FW_Outside_map 16 match address outside_cryptomap_16 crypto map FW_Outside_map 16 set peer x.x.x.134 crypto map FW_Outside_map 16 set transform-set SECURE crypto map FW_Outside_map 16 set security-association lifetime seconds crypto map FW_Outside_map 17 match address Lit crypto map FW_Outside_map 17 set peer x.x.x.110 crypto map FW_Outside_map 17 set transform-set SECURE crypto map FW_Outside_map 18 match address Mid crypto map FW_Outside_map 18 set peer 78.x.x.110 crypto map FW_Outside_map 18 set transform-set SECURE crypto map FW_Outside_map 19 match address Sp crypto map FW_Outside_map 19 set peer x.x.x.47 crypto map FW_Outside_map 19 set transform-set SECURE crypto map FW_Outside_map 20 match address Tor crypto map FW_Outside_map 20 set peer x.x.x.184 crypto map FW_Outside_map 20 set transform-set SECURE crypto map FW_Outside_map 21 match address Tr crypto map FW_Outside_map 21 set peer x.x.x.75 crypto map FW_Outside_map 21 set transform-set SECURE crypto map FW_Outside_map 22 match address Yo crypto map FW_Outside_map 22 set peer x.x.x.40 crypto map FW_Outside_map 22 set transform-set SECURE crypto map FW_Outside_map 23 match address Tra crypto map FW_Outside_map 23 set peer x.x.x.145 crypto map FW_Outside_map 23 set transform-set SECURE crypto map FW_Outside_map 24 match address outside_cryptomap_24 crypto map FW_Outside_map 24 set peer x.x.x.46 crypto map FW_Outside_map 24 set transform-set SECURE crypto map FW_Outside_map 24 set security-association lifetime seconds crypto map FW_Outside_map 25 match address Nor crypto map FW_Outside_map 25 set peer x.x.x.70 crypto map FW_Outside_map 25 set transform-set SECURE crypto map FW_Outside_map 26 match address Ilk crypto map FW_Outside_map 26 set peer x.x.x.65 crypto map FW_Outside_map 26 set transform-set SECURE crypto map FW_Outside_map 27 match address Nor crypto map FW_Outside_map 27 set peer x.x.x.240 crypto map FW_Outside_map 27 set transform-set SECURE crypto map FW_Outside_map 28 match address ST crypto map FW_Outside_map 28 set peer x.x.x.163 crypto map FW_Outside_map 28 set transform-set SECURE crypto map FW_Outside_map 28 set security-association lifetime seconds crypto map FW_Outside_map 28 set security-association lifetime kilobytes crypto map FW_Outside_map 29 match address Lei crypto map FW_Outside_map 29 set peer x.x.x.4 crypto map FW_Outside_map 29 set transform-set SECURE crypto map FW_Outside_map 30 match address outside_cryptomap_30 crypto map FW_Outside_map 30 set peer x.x.x.34 crypto map FW_Outside_map 30 set transform-set SECURE crypto map FW_Outside_map 31 match address outside_31_cryptomap crypto map FW_Outside_map 31 set pfs crypto map FW_Outside_map 31 set peer Cisco-admin-Peer crypto map FW_Outside_map 31 set transform-set ESP-AES-256-SHA crypto map FW_Outside_map 32 match address outside_32_cryptomap crypto map FW_Outside_map 32 set pfs crypto map FW_Outside_map 32 set peer HQ-SDSL-Peer crypto map FW_Outside_map 32 set transform-set ESP-AES-256-SHA crypto map FW_Outside_map 34 match address outside_cryptomap_34 crypto map FW_Outside_map 34 set peer x.x.x.246 crypto map FW_Outside_map 34 set transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA crypto map FW_Outside_map 65535 ipsec-isakmp dynamic dynmap crypto map FW_Outside_map interface outside crypto map FW_outside_map 31 set peer x.x.x.45 crypto isakmp identity address crypto isakmp enable outside crypto isakmp policy 9 webvpn enable outside svc enable group-policy ASA-LAN-VPN internal group-policy ASA_LAN-VPN attributes wins-server value 192.168.x.1 192.168.x.2 dns-server value 192.168.x.1 192.168.x.2 vpn-tunnel-protocol IPSec svc split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel-ACL default-domain value MYdomain username xxxxxxxxxx password privilege 15 tunnel-group DefaultRAGroup ipsec-attributes isakmp keepalive threshold 30 retry 2 tunnel-group DefaultWEBVPNGroup ipsec-attributes isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.121 type ipsec-l2l tunnel-group x.x.x..121 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.202 type ipsec-l2l tunnel-group x.x.x.202 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.113 type ipsec-l2l tunnel-group x.x.x.113 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.205 type ipsec-l2l tunnel-group x.x.x.205 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.204 type ipsec-l2l tunnel-group x.x.x.204 ipsec-attributes pre-shared-key * isakmp keepalive threshold 30 retry 2 tunnel-group x.x.x.212 type ipsec-l2l tunnel-group x.x.x.212 ipsec-attributes pre-shared-key * tunnel-group x.x.x.215 type ipsec-l2l tunnel-group x.x.x.215 ipsec-attributes pre-shared-key * tunnel-group x.x.x.247 type ipsec-l2l tunnel-group x.x.x.247 ipsec-attributes pre-shared-key * tunnel-group x.x.x.170 type ipsec-l2l tunnel-group x.x.x.170 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x..8 type ipsec-l2l tunnel-group x.x.x.8 ipsec-attributes pre-shared-key * tunnel-group x.x.x.212 type ipsec-l2l tunnel-group x.x.x.212 ipsec-attributes pre-shared-key * tunnel-group x.x.x.230 type ipsec-l2l tunnel-group x.x.x.230 ipsec-attributes pre-shared-key * tunnel-group x.x.x.24 type ipsec-l2l tunnel-group x.x.x.24 ipsec-attributes pre-shared-key * tunnel-group x.x.x.46 type ipsec-l2l tunnel-group x.x.x.46 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.4 type ipsec-l2l tunnel-group x.x.x.4 ipsec-attributes pre-shared-key * tunnel-group x.x.x.110 type ipsec-l2l tunnel-group x.x.x.110 ipsec-attributes pre-shared-key * tunnel-group 78.x.x.110 type ipsec-l2l tunnel-group 78.x.x.110 ipsec-attributes pre-shared-key * tunnel-group x.x.x.47 type ipsec-l2l tunnel-group x.x.x.47 ipsec-attributes pre-shared-key * tunnel-group x.x.x.34 type ipsec-l2l tunnel-group x.x.x.34 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x..129 type ipsec-l2l tunnel-group x.x.x.129 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.94 type ipsec-l2l tunnel-group x.x.x.94 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.40 type ipsec-l2l tunnel-group x.x.x.40 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.65 type ipsec-l2l tunnel-group x.x.x.65 ipsec-attributes pre-shared-key * tunnel-group x.x.x.70 type ipsec-l2l tunnel-group x.x.x.70 ipsec-attributes pre-shared-key * tunnel-group x.x.x.134 type ipsec-l2l tunnel-group x.x.x.134 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.163 type ipsec-l2l tunnel-group x.x.x.163 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.2 type ipsec-l2l tunnel-group x.x.x.2 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group ASA-LAN-VPN type remote-access tunnel-group ASA-LAN-VPN general-attributes address-pool RAS-VPN authentication-server-group vpn authentication-server-group (outside) vpn default-group-policy ASA-LAN-VPN tunnel-group ASA-LAN-VPN ipsec-attributes pre-shared-key * tunnel-group x.x.x.184 type ipsec-l2l tunnel-group x.x.x.184 ipsec-attributes pre-shared-key * tunnel-group x.x.x.145 type ipsec-l2l tunnel-group x.x.x.145 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.75 type ipsec-l2l tunnel-group x.x.x.75 ipsec-attributes pre-shared-key * tunnel-group x.x.x.246 type ipsec-l2l tunnel-group x.x.x.246 ipsec-attributes pre-shared-key * isakmp keepalive disable tunnel-group x.x.x.2 type ipsec-l2l tunnel-group x.x.x..2 ipsec-attributes pre-shared-key * tunnel-group x.x.x.98 type ipsec-l2l tunnel-group x.x.x.98 ipsec-attributes pre-shared-key * ! ! ! policy-map global_policy description Netflow class class-default flow-export event-type all destination MS-ISA-Server policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 Anyone have a clue because Im on the verge of going postal.....

  Read the article

• Ubuntu 8.04 server is not retaining a static IP address

  - by James Pierce

  I recently setup a linux box running Ubuntu 8.04 (to match another server with 8.04). I need to insure that this box has a static IP address and I changed /etc/network/interfaces to set up the static IP address and when I run sudo /etc/init.d/networking restart it works fine for a while, but always reverts back to 10.0.1.24 after being idle for a while. I also tried stopping/removing the dhcp client, but that didn't help. sudo /etc/init.d/dhcp stop sudo apt-get remove dhcp3-client Here is my /etc/init.d/networking: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.0.1.4 netmask 255.255.255.0 broadcast 10.0.1.255 gateway 10.0.1.1 Any thoughts? Thanks.

  Read the article

• OpenVPN - Ubuntu 10.04 - Client Can't Connect to Server - Linux Route Add Command Failed

  - by nicorellius

  I suppose this could be asked on Server Fault as well, but it is specific to the client so I thought I'd start here. I have keys for access to an OpenVPN server already in place. I have used these keys to connect already, but using a Windows XP machine. On a Ubuntu machine, I installed OpenVPN and then configured client.conf file so that I could run: sudo openvpn --config client.conf And it seems correct but I still can't connect and get these errors and lines of output: Mon May 31 14:34:57 2010 ERROR: Linux route add command failed: external program exited with error status: 7 Mon May 31 14:34:57 2010 /sbin/route add -net 10.8.0.1 netmask 255.255.255.255 gw 10.8.0.17 SIOCADDRT: File exists Mon May 31 14:34:57 2010 ERROR: Linux route add command failed: external program exited with error status: 7 Mon May 31 14:34:57 2010 Initialization Sequence Completed I searched the net for forums and ideas and tried some file moving and renaming but still ended up in the same place.

  Read the article

• Juniper SSG-5 subinterface vlan routing to the internet

  - by catfish

  I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• vpnc Not Adding Internal DNS Servers to resolv.conf

  - by AJ

  I'm trying to setup vpnc on Ubuntu. When I run vpnc, my resolv.conf file does not get changed. It still only contains my ISP's name servers: #@VPNC_GENERATED@ -- this file is generated by vpnc # and will be overwritten by vpnc # as long as the above mark is intact nameserver 65.32.5.111 nameserver 65.32.5.112 Here is my /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.3 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 65.32.5.111 65.32.5.112 Any tips on how to troubleshoot/resolve this? Thanks in advance.

  Read the article

• Step by Step Install of MAAS and JUJU

  - by John S

  I am working on understanding the pieces that I am missing in being able to deploy Juju across the other MAAS nodes. I don't know If I have a step out of place, or missing a few. The server owns the router which handles the DHCP and DNS. Any assistance is greatly appreciated. When I am at the end I will either get a 409 error, or arbitrary pick tools 1.16.0 error. It is worth mentioning that local, and aws works fine. Hopefully with all of these steps spelled out it will help someone else along the way too. Steps Setting Up MAAS and JUJU - 12.04 LTS Clean install SSH only from the package selection during install sudo apt-get install software-properties-common sudo apt-get install python-software-properties sudo add-apt-repository ppa:maas-maintainers/stable sudo add-apt-repository ppa:juju/stable sudo apt-get update sudo apt-get dist-upgrade sudo reboot sudo apt-get install maas maas-dns maas-dhcp sudo ufw disable sudo reboot - edit /etc/dhcp/dhcpd.conf authoritive subnet 10.0.0.0 netmask 255.255.255.0 { next-server 10.0.0.2; filename "pxelinux.0"; } sudo maas createsuperuser sudo maas-import-pxe-files Login to MAAS http://10.x.x.x/MAAS cluster controller configuration for eth0 manage dhcp and dns IP 10.0.0.2 subnet 255.255.255.0 broadcast 10.0.0.0 routerip 10.0.0.1 ip low 10.0.0.5 ip high 10.0.0.180 Commissioning default and distro is set at 12.04 default domain is at local sudo maas-cli login maas http://10.x.x.x/MAAS/api/1.0 api-key ssh-keygen -t rsa -b 2048 - enter - no password - cat id_rsa.pub and enter key into MAAS ssh sudo maas-cli maas nodes accept-all (interestingly enough I only get back [] when executing this ) PXE one machine, accept and commision, start and deploy. sudo apt-get install juju-core juju-local MAAS config: maas: type: maas maas-server: '://10.x.x.x:80/MAAS' maas-oauth: 'MAAS_API_KEY' admin-secret: 'nothing' default-series: 'precise' juju switch maas sudo juju bootstrap --show-log

  Read the article

• ServerFault Wiki: How does Subnetting Work?

  - by Kyle Brandt

  How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Serverfault gets lots of subnetting homework questions, so we could use an answer to point them to on serverfault itself. If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? Not looking for links to other sites (unless maybe you have one post with a bunch of good ones). I already know how to subnet, I just thought it would be nice if serverfault had a generic subnetting answer.

  Read the article

• virtualbox, MAAS: help needed

  - by Roberto Attias

  Ok, I made some progress wrt the original question (still below). I found /etc/maas/dhcpd.conf contained option domain-name-servers 10.0.3.15, and changed it to 192.168.0.11. After restarting the daemon, I now see "node" getting the right DNS, unfortunately this doesn't fix the main problem, which I believe is the reference to 169.254.169.254. It does introduce a new question: while the remaining information from /etc/maas/dhcp.conf is present in the maas GUI, there is no field to enter the dns address. Why? Anyway, my original problem still stands... Any idea? Original question follows. In VirtualBox, I have: master VM: ubuntu 12.04.3 server eth0: Internal Network, IP= 192.168.0.11 eth1: NAT, IP= 10.0.3.15 eth2: Host-only, IP= 192.168.56.102 running MAAS region and cluster controlller, with DHCP and DNS enabled node VM: eth0: Internal Network node VM boots in PXEboot. DHCP succeeds, and the boot process starts, but during boot I see some issues. One of them is "disk drive not ready yet or not present" for / and /tmp. I've googled this issue, and some people say it happens when the fisical disk is a SSD, which is my case. Anywaythe system seems to recover from this eventually. Immediately after it starts printing a lot of messages of the form: 2013-10-01 16:52:37,142 - url_helper.py[WARNING]: Calling 'http://169.254.168.254/2009-04-04/meta-data/instance-id failed [x/y]: url error [[Errno 113] No route to host] That IP address is clearly bogous, not sure where it came from. Before that point, I had seen the following network configuration: address: 192.168.0.100 broadcast: 192.168.0.255 netmask: 255.255.255.0 gateway: 192.168.0.1 dns0 : 10.0.3.15 dns1 : 0.0.0.0 Not sure if related, but the dns doesn't seem right, as node doesn't have an interface to reach 10.0.3.15. If that's the problem, what should I change to have the DNS point to 192.168.0.11? Thanks, Roberto

  Read the article

• Where Debian Lenny stores initial ifconfig values?

  - by Kuroki Kaze

  With upgrade of VMWare Player I suddenly found my Debian Lenny VM not getting IP address. Some DHCP issue maybe, I don't know. So I have to set it manually every boot in Player window, via: ifconfig eth0 down ifconfig eth0 192.168.175.128 netmask 255.255.255.0 up I usually start up VM and then connect to it via SSH, so this procedure bothers me. Sure I can add it to startup script, but is there some special place to enter these values? Like, some config file or so?

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >