Search Results

Search found 2795 results on 112 pages for 'nic strong'.

Page 10/112 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• NIC going to sleep on Ubuntu Server 10.04

  - by user43390

  When I leave my server idle for about 10 minutes the network will stop responding to outside connections. If I get on the server and attempt to use the network(ping google for example) there will be a delay for a few seconds and then it works. After this incoming connections work again until I leave it idle again. Why does this happen and how can I fix it?

  Read the article

• How to send pcap file packets on NIC?

  - by salman

  I have some network traffic captured pcap file and want to send its packets on NIC; is it possible? Is there any application to do this?

  Read the article

• Using <strong> for introductory paragraph to a post - a bad idea?

  - by user1515699

  I have a news website and on most posts the first paragraph is in bold. Currently the authors are just using <strong> to bold the paragraph, would it be better from an SEO point of view to rather use a paragraph class that is styled with p.bold {font-weight:bold;} <p class="bold">. Does <strong> on the first paragraph send the wrong message to search engines? The text is important but the main reason it is in bold is because it is the opening paragraph. I realise <strong> is used to emphasise certain words on a page

  Read the article

• Are factors such as Intellisense support and strong typing enough to justify the use of an 'Anaemic Domain Model'?

  - by David Osborne

  It's easy to accept that objects should be used in all layers except a layer nominated as a data layer. However, it's just as easy to end-up with an 'anaemic domain model' that is just an object representation of data with no real functionality ( http://martinfowler.com/bliki/AnemicDomainModel.html ). However, using objects in this fashion brings the benefit of factors such as Intellisense support, strong typing, readability, discoverability, etc. Are these factors strong arguments for an otherwise, anaemic domain model?

  Read the article

• Strong Naming an assembly using command line compile

  - by David

  I am trying to use NAnt in order to compile and sign an assembly using the vbc compiler. I have a project set up and am able to successfully sign the assembly compiling with VS2010. When I try to sign it using the command line I get this error: vbc : error BC30140: Error creating assembly manifest: Error signing assembly -- The parameter is incorrect. I even created a trivially simple app (just an assemblyinfo.vb file) that will not compile and sign using vbc.exe What am I doing wrong? here is my assemblyinfo.vb: Option Strict Off Option Explicit On Imports System Imports System.Reflection <Assembly: AssemblyVersionAttribute("2010.05.18.0918"), _ Assembly: AssemblyCopyrightAttribute("Copyright © Patient First 2007"), _ Assembly: AssemblyCompanyAttribute("Patient First, Inc."), _ Assembly: AssemblyProductAttribute("Patient First Framework"), _ Assembly: AssemblyDelaySign(false), _ Assembly: AssemblyKeyFile("test.pfx"), _ Assembly: AssemblyTitleAttribute("PatientFirst.Framework")> test.pfx is located in the same folder as assemblyinfo.vb Here is how I am trying to compile it: vbc /target:library /verbose assemblyinfo.vb I also tried using vbc /target:library /verbose assemblyinfo.vb /keyfile:test.pfx and tried using /keyfile parameter without the AssemblyDelaySign and AssemblyKeyFile attributes If I remove the AssemblyDelaySign and AssemblyKeyFile attributes and leave off the /keyfile command line parameter it compiles fine. What is the correct way to do this with vbc? --EDIT: I have found that MSBuild also does not like having the AssemblyKeyFile attribute as I have defined it in the AssemblyInfo.vb, it gives the same failure message. So the only way I can currently get this to build correctly is to set properties on the project to tell it which key file to use and to sign the assembly.

  Read the article

• MVC2 Strong typing breaking changes...

  - by BitFiddler

  I had the code working for: http://stackoverflow.com/questions/1930229/post-idictionary-back-to-mvc-model I recently migrated to MVC2 and now all my collections/dictionaries are coming back null. I can't seem to find any information about what has changed in the new release to cause this. Anyone know of something that might help?

  Read the article

• VOIP Softphone with API or strong command line interface

  - by garyb_54654564654

  Does anyone know of a sip softphone that can be controller by an API. Xlite can launch a call through command line interface, but thats pretty much it, preferably looking for something cheap, the voip SDKs iv seen are pretty expensive and i wouldn't have any knowledge of sip protocol or development.

  Read the article

• php regex for strong password validation

  - by Jason

  Hello, I've seen around the web the following regex (?=^.{8,}$)((?=.*\d)|(?=.*\W+))(?![.\n])(?=.*[A-Z])(?=.*[a-z]).*$ which validates only if the string: * contain at least (1) upper case letter * contain at least (1) lower case letter * contain at least (1) number or special character * contain at least (8) characters in length I'd like to know how to convert this regex so that it checks the string to * contain at least (2) upper case letter * contain at least (2) lower case letter * contain at least (2) digits * contain at least (2) special character * contain at least (8) characters in length well if it contains at least 2 upper,lower,digits and special chars then I wouldn't need the 8 characters length. special characters include: `~!@#$%^&*()_-+=[]\|{};:'".,/<? thanks in advance.

  Read the article

• ASP.Net Create User Control with Strong Password

  - by Burt

  I need a control that will accept an email address and password/verify with a password strength indicator. Has anyone seen a similar type control?

  Read the article

• Wrap words in tags, keep markup

  - by spacevillain

  For example I have a string with markup (from html node): hello, this is dog "h<em>e<strong>llo, thi</strong>s i</em><strong>s d</strong>og" What is the most correct way to find some words in it (let's say "hello" and "dog"), wrap them in a span (make a highlight) and save all the markup? Desired output is something like this (notice properly closed tags) <span class="highlight">h<em>e<strong>llo</strong></em></span><strong>,</strong> <em><strong>thi</strong>s<em> i</em><strong>s <span class="highlight"><strong>d</strong>og</span> Looks the same as it should: hello, this is dog

  Read the article

• establishing strong web security

  - by berj

  i have seen many sites who claim to have bank grade security encription. if their web sites have been built with php what other forms of security can exist aside from using mysql_real_escape_string and a 128bit ssl encription?

  Read the article

• Add IP Address without Plesk

  - by CrackerJack9

  I have an dedicated unmanaged server and added a few IP addresses to it (allocated), and the only information my hosting company has provided is instructions on how to use Plesk to Add IP Addresses. However, one of the first things I did was uninstall Plesk (for numerous reasons). Does anyone know what exactly Plesk does when you "Add IP Address"? Does it just create an alias on the default interface (I currently only have one and the loopback)? I can manage that myself without Plesk, but I was hoping someone might know if there is anything else Plesk does. I also have DHCP Client running (eth0 is static), not sure why my hosting company put that there either, and not sure if they're related.

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• allowing 2 VM's to communicate RED HAT 64 bit

  - by ????? ????????

  My physical PC is running 2 VMs on virtualbox. Both of the VM's are linux 64 bit. I am going through this tutorial: http://www.cyberciti.biz/faq/rhel-centos-fedoracore-linux-network-card-configuration/ in order to expose both of their IP's so that they can speak to each other. Mike Schwager November 25, 2009 at 10:55 pm Whoops! In section 3, you forgot about editing /etc/hosts. I believe RedHat comes complete with the system’s host ip address set up in /etc/hosts. Don’t forget to give it a look. I agree with Mike because after I looked into the /etc/hosts files, it has just default localhost stuff in it. How should I reconfigure the hosts file?

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• OS X will not register newly installed network adapters

  - by Chris

  I have purchased an Edimax 7318USg and tested it on a Windows machine (works). The installation process for the software for this adapter runs smoothly. However, OS X simply does not recognize new network adapters. When you go to System Preferences/Network, a new network adapter should be present/there should be an alert. This is not the case. Why might this be? Is there a setting I may reset to force the operating system to recognize this? Thanks!

  Read the article

• Teamed network cards on a Proliant Server

  - by Matt

  We have 4 network cards in a Proliant server with Server 2008R2 running Exchange 2010, with 1 card set to a static IP address and the other 3 set to DHCP. I just need some clarification as I have not teamed network cards. Do all the network cards need to have a static IP when I set as a team. The connection that has the static IP is the IP that I need to use for the Server. Is it possible to set the teamed cards to the same static IP or do I have to change the static IP to another IP then use it for the teamed IP? I will be using HP Network Configuration Utility to set this up.

  Read the article

• How to Load Balance 2 Internet Connections on a Windows 7 machine?

  - by Jimmy Chandra

  It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

  Read the article

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Windows 2008, 2 NICS, routing problem

  - by Srodriguez

  Dear all, I've some questions regarding basic routing, can't seem to relate to other questions posted in this site. My architecture: Windows 2008 server with 2 nics in the server. NIC1: IP 10.198.6.xxx, submask 255.255.252.0, gateway 10.198.4.xxx NIC2: IP 192.168.168.xxx, submask 255.255.255, no gateway defined both NICS are just connected to two separate switches, with other computers. I want to be able that all the requests that have a destination of 192.168.168.xxx are redirected to the NIC2, all the other to the NIC1. I know it's possible to do it with the route command, but normally we have to specify a gateway? (route ADD 192.168.168.0 MASK 255.255.255.0 ???) How can this be archived? Thanks a lot for your help!

  Read the article

• realtek lan driver problem - win 7

  - by tango _123

  Hi, my new notebook (ACER TM 8371) with Win 7(x32) professional as OS, has strage behaviour with respect to LAN. when I plug or unplug my charger cable, or my notebook goes in stad-by, or just a do nothing, the netwrok connection is lost. All the energy savings functionbality have been in-activated. if i check the network adapter information, it says "a network cabel is unplugged or corrupted", but it is not true.....the cable is in and it is not corrupted (i tried several which works on other machines). if a tried to di-habilitate and hence re-habilitate, it allows di-habilitation and not to further re-habilitate (it says "no driver for the network card" are available). in some cases, also, the driver disappears (i cannot see it anylonger). if i restart the notebook, everything comes back to normality, but.....today in 3 hours i had to restart 6 times!!! can anyone help me? win 7 says the driver is the last one, so no need to update it. here are some techinical information aboiut network card and driver: Name [00000015] Realtek PCIe GBE Family Controller Adapter type Ethernet 802.3 Product type Realtek PCIe GBE Family Controller Installated YES ID device PNP PCI\VEN_10EC&DEV_8168&SUBSYS_02831025&REV_02\4&266E4C4F&0&00E2 last reset 20/11/2009 11:27 Index 15 Service name RTL8167 I/O Port 0x0000FF00-0x0000FFFF Memory address 0xE2500000-0xE2500FFF Memory address 0xE1400000-0xE140FFFF IRQ Channel IRQ 18 Driver c:\windows\system32\drivers\rt86win7.sys (7.3.522.2009, 164,00 KB (167.936 Byte), 28/08/2009 22:12)

  Read the article

• Centos VM serving multiple public IP: how to configure network interface?

  - by Glasnhost

  I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• What is the fall off of subsecond throughput on Ethernet Network Interfaces

  - by Kyle Brandt

  On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >