Search Results

Search found 61490 results on 2460 pages for 'windows mobile 6 1'.

Page 10/2460 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Easiest way to replace preinstalled Windows 8 with new hard drive with Windows 7

    - by Andrew
    There are all kinds of questions and answers relevant moving Windows 8 to a new hard drive. I'm not seeing anything quite applicable to my situation. I have a new, unopened, unbooted notebook with pre-installed Windows 8. I will be replacing the hard drive before ever booting, unless that is not possible for some reason. I want to "downgrade" to Windows 7 Pro, and I want a clean installation. To do so legitimately, I apparently either need to: Upgrade Windows 8 to Windows 8 Pro using Windows 8 Pro Pack, then downgrade; or Just install a newly-licensed copy of Windows 7 Pro. (Let me know if I've missed an option.) Installation media is likely not a problem, though if I need something vendor-specific that I cannot otherwise download, that could present an issue (Asus notebook, if that matters). If I could, I would just buy the Pro Pack upgrade, swap the hard drive (without ever booting), then install Windows 7 Pro directly on the new hard drive, using the Pro Pack key for activation. Will this work? Are there any activation issues? Edited to clarify, as some comments and answers indicate confusion: Here is, ideally, what I want to do: Before ever powering on the notebook, remove the current hard drive. Replace this hard drive with a new, blank hard drive. Install a clean copy of Windows 7 Pro on this new, blank hard drive. Unless I have no choice to accomplish the end result (a clean install of Win7 Pro on the newly-installed, previously-blank hard drive), I am not wanting to: Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro). That would involve using the currenly-installed hard drive. I want to use a new, different hard drive. Copy the Win8 install to the new hard drive, then install Windows 7 "over" that installation. Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro), then copy the installation to the new hard drive. If I have to use one of those three options, I will, but only if there is no other choice. Please note that this question is not about licensing: I will purchase the necessary license(s) to accomplish this procedure legally (apparently either Win8 Pro Pack or Win7 Pro -- the former currently appears less expensive).

    Read the article

  • Five Best Practices for Going Mobile

    - by kellsey.ruppel
    76% of IT decision makers indicate mobile trends will have a high to extremely high impact on their organization. Has your organization gone mobile? Looking for some ideas on how to get started? John Brunswick shares his Best Practices for Going Mobile. Mobile technology has gone from nice-to-have to a cornerstone of user engagement. Mobile access enables social networking, decision support, purchasing, content consumption, and location-based searching, extending experiences beyond what is available in traditional desktop computing.  Organizations rushing to ensure their brand's mobile availability may have taken a tactical approach to implementation, but strategically approaching mobile can enable greater returns on a similar investment and subsequent mobile projects. Here are some strategic considerations for delivering products, services, and information to mobile constituents.  Who, Why, and What? Ask yourself these key questions: who are you attempting to engage through the channel, and why are they engaging you through this channel? What experience will satisfy their needs? What outcome will support your core business? Will you be informing and/or transacting with this person?  Mobile Behavior. Mobile users generally engage for a very specific purpose. Ensure that access to information, services, and products is streamlined. Arriving on a mobile site through search only to be asked to search again frustrates users.  Mobile Is Broad. After establishing the audience and goal, review technology requirements to support them. Do you need a mobile Website, native mobile application, or both? Do you need to support multiple devices? Know the difference between native mobile and mobile Web.  Social Strategy. Users are more likely to trust reviews from peers than marketing information from a vendor. If you are selling products or services, be sure to make social integration part of your strategy.  Content Management. Consider a shared content platform strategy for Web and mobile projects. Fresh, consistent content is important for high-quality experiences. Read more from John Brunswick.We'll also be talking mobile strategies and how you can transform your portal experience and optimize online engagement -- making your portals more interactive and more engaging across multiple channels in a webcast tomorrow. We hope you'll join us!

    Read the article

  • Windows 7 x64 "upgrade" repair fails

    - by Polynomial
    I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

    Read the article

  • Map a Network Drive from XP to Windows 7

    - by Mysticgeek
    We’ve received a lot of questions about mapping a drive from XP to Windows 7 to access data easily. Today we look at how to map a drive in Windows 7, and how to map to an XP drive from Windows 7. With the new Homegroup feature in Windows 7, it makes sharing data between computers a lot easier. But you might need to map a network drive so you can go directly into a folder to access its contents. Mapping a network drive may sound like “IT talk”, but the process is fairly easy. Map Network Drive in Windows 7 Note: All of the computers used in this article are part of the same workgroup on a home network. In this first example we’re mapping to another Windows 7 drive on the network. Open Computer and from the toolbar click on Map Network Drive. Alternately in Computer you can hit “Alt+T” to pull up the toolbar and click on Tools \ Map Network Drive. Now give it an available drive letter, type in the path or browse to the folder you want to map to. Check the box next to Reconnect at logon if you want it available after a reboot, and click Finish. If both machines aren’t part of the same Homegroup, you may be prompted to enter in a username and password. Make sure and check the box next to Remember my credentials if you don’t want to log in every time to access it. The drive will map and the contents of the folder will open up. When you look in Computer, you’ll see the drive under network location. This process works if you want to connect to a server drive as well. In this example we map to a Home Server drive. Map an XP Drive to Windows 7 There might be times when you need to map a drive on an XP machine on your network. There are extra steps you’ll need to take to make it work however. Here we take a look at the problem you’ll encounter when trying to map to an XP machine if things aren’t set up correctly. If you try to browse to your XP machine you’ll see a message that you don’t have permission. Or if you try to enter in the path directly, you’ll be prompted for a username and password, and the annoyance is, no matter what credentials you put in, you can’t connect. To solve the problem we need to set up the Windows 7 machine as a user on the XP machine and make them part of the Administrators group. Right-click My Computer and select Manage. Under Computer Management expand Local Users and Groups and click on the Users folder. Right-click an empty area and click New User. Add in the user credentials, uncheck User must change password at next logon, then check Password never expires then click Create. Now you see the new user you created in the list. After the user is added you might want to reboot before proceeding to the next step.   Next we need to make the user part of the Administrators group. So go back into Computer Management \ Local Users and Groups \ Groups then double click on Administrators. Click the Add button in Administrators Properties window. Enter in the new user you created and click OK. An easy way to do this is to enter the name of the user you created then click Check Names and the path will be entered in for you. Now you see the user as a member of the Administrators group. Back on the Windows 7 machine we’ll start the process of mapping a drive. Here we’re browsing to the XP Media Center Edition machine. Now we can enter in the user name and password we just created. If you only want to access specific shared folders on the XP machine you can browse to them. Or if you want to map to the entire drive, enter in the drive path where in this example it’s “\\XPMCE\C$” –Don’t forget the “$” sign after the local drive letter. Then login… Again the contents of the drive will open up for you to access. Here you can see we have two drives mapped. One to another Windows 7 machine on the network, and the other one to the XP computer.   If you ever want to disconnect a drive, just right-click on it and then Disconnect. There are several scenarios where you might want to map a drive in Windows 7 to access specific data. It takes a little bit of work but you can map to an XP drive from Windows 7 as well. This comes in handy where you have a network with different versions of Windows running on it. Similar Articles Productive Geek Tips Find Your Missing USB Drive on Windows XPMake Vista Index Your Network ConnectionsEasily Backup & Import Your Wireless Network Settings in Windows 7Quickly Open Network Connections List in Windows 7 or VistaHow To Find Drives Easily with Desk Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Kill Processes Quickly with Process Assassin Need to Come Up with a Good Name? Try Wordoid StockFox puts a Lightweight Stock Ticker in your Statusbar Explore Google Public Data Visually The Ultimate Excel Cheatsheet Convert the Quick Launch Bar into a Super Application Launcher

    Read the article

  • How to Change and Manually Start and Stop Automatic Maintenance in Windows 8

    - by Lori Kaufman
    Windows 8 has a new feature that allows you to automatically run scheduled daily maintenance on your computer. These maintenance tasks run in the background and include security updating and scanning, Windows software updates, disk defragmentation, system diagnostics, among other tasks. We’ve previously shown you how to automate maintenance in Windows 7, Vista, and XP. Windows 8 maintenance is automatic by default and the performance and energy efficiency has been improved over Windows 7. The program for Windows 8 automatic maintenance is called MSchedExe.exe and it is located in the C:\Windows\System32 directory. We will show you how you can change the automatic maintenance settings in Windows 8 and how you can start and stop the maintenance manually. NOTE: It seems that you cannot turn off the automatic maintenance in Windows 8. You can only change the settings and start and stop it manually. Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked

    Read the article

  • How did I get here? My route to Android, iPhone, Windows Phone 7, and interest in Mobile Devices

    - by Wallym
    I get asked all the time how/why I got interested in mobile and jumped on this fairly early.  I tend to give half answers because it wasn't just one thing that took me to mobile, but a whole host of separate ivents culminating in a specific event where I wasdoing market research in May/June 2008.  Let me throw out the events and the facts about me: I tend to like new, different, cool stuff.  I jumped on .NET early on.  I jumped on Ajax early on.  I don't jump on every new technology that comes down the road, I'm probably the only person on the planet that doesn't "get" MVC, though I acknowledge that a lot of people do and it solves a number of problems in the default settings of ASP.NET WebForms. I remember buying an early Windows CE device. It was interesting, but dang, this stylus thing sucks. After I lost my third stylus, i just gave up.  I got my first mobile phone in early 1999.  Reception was crappy, but I could see the value in being mobile. In 1999, I worked on a manufacturing systems project.  One piece of the projects was a set of handheld devices on the shop floor.  While the UI was a crappy DOS based, yes I said DOS as in Disk Operating System Version 6.22, I could see that the wireless world was a direction I wanted to be in. In 2000, Microsoft released the first public alpha of .NET.  Very cool stuff indeed.  One piece of the puzzle was a set of mobile controls for ASP.NET.  I build numerous test apps as well as mobile version using these mobile controls.  Now, the mobile UIs of the time were based on WML, which was crap. I could real all the analysis of mobile and read all about growth rates.  Now, you have to realize that growth rates can be impressive when dealing with small numbers, but I knew it was a comer. In our first book, I got talked out of mobile because of the line from the publisher "Wally, mobile doesn't sell." Blackberry was the dominant device of the mid 2000s.  Its users were referred to as "Crackberry addicts."  Unfortunately, the mobile development experience for native apps was crap and the web experience was fairly rough as well, but if they could get the ecosystem started, other phones and better blackberryies would come out.  I finally jumped into using a blackberry. Sometime around 2006, I heard "Wally, mobile doesn't sell" again.  Now, anyone that knows me knows that someone saying something like this to me means I'll keep trying it. The phones of the mid 2000s were moving to be more graphical, but there were too many that had this idea that they had to use a stylus.  Stylus suck.  They get lost too easily. I worked on a project in 2007 and 2008 for a startup trying to answer the question of "What is there to do where I am at?"  For some reason, they wanted to be tied to PCs.  As it became obvious that they were having problems, their investor asked us to do some market research and to figure out what the marketplace did want.  One of the important things that I figured out was the we lived in a mobile world and if you had a mobile app, it need to be on a mobile device, not tied to a desktop/laptop/netbook device.  If there was any single event, this was it - I was doing some market research and sat and talked to people in a bar/restaurant in Atlanta called "The Grove" on Lavista.  The consensus of the people that I talked to was that they wanted their data where ever they were at, laptop, pc, mobile, whereever. In 2007, Apple released the iPhone.  Wow, what an impressive device, even with all the problems of a 1st generation device.  I bought an iPod Touch 1st generation to understand touch better, one of the best decisions I ever made. I decided in late 2008, to make a move into cloud, for a number of reasons.  I was working on an example app.  In April, 2009, one of my friends at Microsoft said "don't mention my name with this, but you need an iPhone front end for this app."  How do you get on the iPhone.  Well, there are a number of ways including: ObjectiveC.  Its hard to teach an old dog new tricks, and this dog knows .NET, not ObjectiveC. HTML, web, javascript optimized interface.  yeah, this is possible. PhoneGap.  Now, this is interesting, take an html interface and get it to run on the iPhone, Android, Blackberry, and other platforms.  I thought that this way made the most sense for me until......... MonoTouch.  In May/June 2009, Novell announced a way for .NET/c# developers to write apps for the iPhone.  This is the way that made the most sense to me. Titanium by Appcelerator.  This is similar in concept to PhoneGap.  I haven't played with this much but do want to learn more about it. In July, 2009, I emailed one of my contacts at Wrox to see if they would be interested in a short MonoTouch ebook in their Wrox Blox format.  I fully expected another  response along the lines of "Wally, mobile doesn't sell."  The response I got was "Wally, iPhone is H O T, get started immediately, can you have this to me before Labor Day."  Not quite the response I expected.  Thankfully, we didn't make the Labor Day, first draft date. I kept pushing back because I had a feeling that things were not going to be quite as polished and feature rich as necessary.  After all, Novell doesn't have the resouces of Microsoft's developer division. The ebook shipped on November 30, 2009. On about December, 15, 2009, my editor emailed and said "Your ebook is selling really well, lets do a full book and it by March 1 so get started."  Thankfully, guys like Craig Dunn and Chris Hardy were interested along with Martin and Ror joinged us later on. I bought my wife an iPhone 3Gs in early 2010 to go along with all my iPod Touch devices. I tried to pretend in 2010 that I wasn't that interested in mobile and still had interest in the desktop technologies.  I love the technologies and continue to use them today, but that isn't where my interest is right now.  I'm just about all mobile all the time with my energies.  Our book shipped in the beginning of July, 2010 right in the middle of the Apple FUD.I've been looking at Mobile Web as a way around the AppStores and Apple FUD problems of 2010. With all the Apple self FUD, we became interested in Android.I went up to Dino Esposito at DevConnections in Las Vegas at introduced myself. I've always tried to keep up with what Dino has been doing. I was shocked, he wanted to meet me.  We must have talked for 1.5 hours. It was way more time than I deserved. If you get a chance, go and introduce yourself to Dino. He's a great guy. Microsoft released Windows Phone 7 in the Fall of 2010.  I'm not doing development on that platform at this time.  I think they have a very interesting user interface.  The devices are being positively reviewed.  For my purposes, the devices are limited at this point in time.  We'll see what 2011 brings as far as updates to the operating system.  I need multitasking/background processing and html5 in the browser. Add that as well as acceptance in the marketplace and I'll be more interested in the device. Obviosuly, I'm now working on a MonoDroid book . I own Android and iPhone/iOS devices.  I am currently working on some startup ideas and am exploring as much in that area as I can. For 2011, I'm planning on speaking at Android Developer's Conference (AnDevCon) and Mobile Connections.  I'm really excited about this. I have a couple of magazine articles coming out in 2011 on Android and iPhone development with the Mono technologies.is Mono "The Answer"? What's "The Question?" I think it will work for me.  It might work for you, it might not.  it depends on your situation.  Its the current horse that I am riding. I might find a better horse tomorrow. So, that's how I got here.  I'm in love with mobileMobile native apps on the device as well as mobile web.  I'm into all this cool stuff.  Where are you at?

    Read the article

  • Will an app made for windows store support WindowsRT, windows8 and windows 8 mobile?

    - by AnhSirk Dasarp
    I am very much confused about these. I would like to develop app for windows 8 , Windows RT , and windows mobile. I have windows 8 OS installed in my laptop. As far as I know, Windows RT is for ARM based devices. HERE ARE MY QUESTIONS: I develop an app, and put in windows store. Will that can be downloaded from a ARM based device ,which runs on Windows RT, AND from a windows 8 laptop , and same from a Windows 8 mobile? OR should it be different apps ?

    Read the article

  • Windows 8 permissions vs Windows 7 [closed]

    - by Saturn2888
    Possible Duplicate: How do I disable administrator prompt in Windows 8? When I upgraded from Windows 7 Pro 64-bit to Windows 8 Pro 64-bit, I noticed some permissions issues extremely problematic to my using the OS. When running Windows 7 or Vista with UAC off, I was able to navigate around the filesystem as if I was on Windows XP and prior such that I didn't have to run as administrator and could copy and edit files wherever I wanted. In Windows 8, turning off UAC no longer does this. Does anyone know how to get Windows 8's permissions to act like Windows 7 and Vista when UAC is disabled? NOTE: I did a clean install on my laptop with Windows 8, and it has the same issues.

    Read the article

  • Windows 8 Upgrade : From Windows 7 Trial

    - by Golmaal
    This is a bit complicated it seems. I own Windows Vista Ultimate 64-bit (Retail). It was okay, but around a couple of weeks ago I had some system crash and at that time I decided that I will install Windows 8 as soon as it comes out. However, because of some problems in Vista, at the time of crash, I installed Windows 7 trial. I had some urgent work to do which I accomplished and then I switched the PC off. Now I have purchased Windows 8 Pro Upgrade ($40 version). If I go for a clean install, will it be able to install Windows 8 on not-activated Windows 7? During activation, if it asks for Vista serial number, I can provide it. Or will I first have to install Vista and then only it will allow me to install Windows 8? Also, I used the Upgrade Assistant to download Windows 8 on my laptop (Windows 7 OEM). Will it work on my above mentioned desktop?

    Read the article

  • How to make a folder (D:\xyz) accessible to only me in Windows-XP?

    - by claws
    Hello, I'm using Windows XP on my lab computer. There is a global folder (d:\xyz). This is my folder and I want this folder to be accessible to only me. It should be invisible even if it is visible they shouldn't be able to open this folder. For now my account has administrative privilages. After few days, I don't know if the Admin lets me have these privilages or not. I heard that soon our XP machines will be upgraded to either vista or windows 7. Will the method of making folder in accessible change for other Windows OSes? How to accomplish this?

    Read the article

  • More Mobile Payments

    - by David Dorf
    In the previous post I discussed the Bump Payments from PayPayl, but that's not the only innovative way to make purchases using your phone. Verizon recently announced a partnership with Danal that allows shoppers to charge online purchases to their Verizon bill. For e-commerce sites that accept this type of payment, it's a two step process. At checkout, the shopper enters their mobile number and billing zip code. Then a SMS message is sent to the mobile phone that contains a one-time code that must be entered on the e-commerce site. This two-factor authentication seems pretty secure, and no pre-registration or credit card is necessary. There's a $25 a month maximum, but I bet the limit gets raised as Verizon gets more comfortable with security. Merchants are charged a fee similar to credit card fees. Another example of mobile payments is offered by BlingNation. Customers attach a small NFC sticker to their phones that allows them to "tap" the POS device to make a payment. The NFC chip is connected to their checking account, so the transaction is treated as a debit payment. Text messages are sent to the mobile that confirm the payments so shoppers can easily verify their purchases. BlingNation is working with banks like Adirondack Trust Company and The State Bank of La Junta in Colorado. Heck, you can even send money to inmates in the Arkansas prison system using your mobile phone now that the state of Arkansas supports payments via their mobile website. Everyone is getting into the act now.

    Read the article

  • Mobile Apps for Oracle E-Business Suite

    - by Steven Chan (Oracle Development)
    Many things have changed in the mobile space over the last few years. Here's an update on our strategy for mobile apps for the E-Business Suite. Mobile app strategy We're building our family of mobile apps for the E-Business Suite using Oracle Mobile Application Framework.  This framework allows us to write a single application that can be run on Apple iOS and Google Android platforms. Mobile apps for the E-Business Suite will share a common look-and-feel. The E-Business Suite is a suite of over 200 product modules spanning Financials, Supply Chain, Human Resources, and many other areas. Our mobile app strategy is to release standalone apps for specific product modules.  Our Oracle Timecards app, which allows users to create and submit timecards, is an example of a standalone app. Some common functions that span multiple product areas will have dedicated apps, too. An example of this is our Oracle Approvals app, which allows users to review and approve requests for expenses, requisitions, purchase orders, recruitment vacancies and offers, and more. You can read more about our Oracle Mobile Approvals app here: Now Available: Oracle Mobile Approvals for iOS Our goal is to support smaller screen (e.g. smartphones) as well as larger screens (e.g. tablets), with the smaller screen versions generally delivered first.  Where possible, we will deliver these as universal apps.  An example is our Oracle Mobile Field Service app, which allows field service technicians to remotely access customer, product, service request, and task-related information.  This app can run on a smartphone, while providing a richer experience for tablets. Deploying EBS mobile apps The mobile apps, themselves (i.e. client-side components) can be downloaded by end-users from the Apple iTunes today.  Android versions will be available from Google play. You can monitor this blog for Android-related updates. Where possible, our mobile apps should be deployable with a minimum of server-side changes.  These changes will generally involve a consolidated server-side patch for technology-stack components, and possibly a server-side patch for the functional product module. Updates to existing mobile apps may require new server-side components to enable all of the latest mobile functionality. All EBS product modules are certified for internal intranet deployments (i.e. used by employees within an organization's firewall).  Only a subset of EBS products such as iRecruitment are certified to be deployed externally (i.e. used by non-employees outside of an organization's firewall).  Today, many organizations running the E-Business Suite do not expose their EBS environment externally and all of the mobile apps that we're building are intended for internal employee use.  Recognizing this, our mobile apps are currently designed for users who are connected to the organization's intranet via VPN.  We expect that this may change in future updates to our mobile apps. Mobile apps and internationalization The initial releases of our mobile apps will be in English.  Later updates will include translations for all left-to-right languages supported by the E-Business Suite.  Right-to-left languages will not be translated. Customizing apps for enterprise deployments The current generation of mobile apps for Oracle E-Business Suite cannot be customized. We are evaluating options for limited customizations, including corporate branding with logos, corporate color schemes, and others. This is a potentially-complex area with many tricky implications for deployment and maintenance.  We would be interested in hearing your requirements for customizations in enterprise deployments.Prerequisites Apple iOS 7 and higher Android 4.1 (API level 16) and higher, with minimum CPU/memory configurations listed here EBS 12.1: EBS 12.1.3 Family Packs for the related product module EBS 12.2.3 References Oracle E-Business Suite Mobile Apps, Release 12.1 and 12.2 Documentation (Note 1641772.1) Oracle E-Business Suite Mobile Apps Administrator's Guide, Release 12.1 and 12.2 (Note 1642431.1) Related Articles Using Mobile Devices with Oracle E-Business Suite Apple iPads Certified with Oracle E-Business Suite 12.1 Now Available: Oracle Mobile Approvals for iOS The preceding is intended to outline our general product direction.  It is intended for information purposes only, and may not be incorporated into any contract.   It is not a commitment to deliver any material, code, or functionality, and should not be relied upon in making purchasing decision.  The development, release, and timing of any features or functionality described for Oracle’s products remains at the sole discretion of Oracle.

    Read the article

  • Grub2 -- Dualboot Ubuntu LTS 12.04 and Windows 7 -- Detects two Windows 7 (loader) entries

    - by DarkIron112
    this is the first question I have ever asked the Ubuntu Community. :D I'm fairly new to Ubuntu, but I understand the basics and know how to navigate the Terminal. I also know how to ask for/research my problems before asking for/ help. I have scoured the internet high and low and learned much of how Grub2 works. But nothing has helped me to solve my problem. My problem is this: I have a computer that has three hard drives. It previously had Windows XP, but I upgraded to Windows 7. I also installed Ubuntu 12.04 LTS (Precise Pangolin). During my installation of Windows 7, there was a failure and I had to restart the installation. Afterwards, I installed Ubuntu. After some trouble removing all traces of the XP OS (Ubuntu auto-detected it, but not Windows 7) I got the two OSes working flawlessly. Or, almost. When booting up, Grub2 used to display Ubuntu, Ubuntu Recovery Mode, Other Versions of Linux, memtest, followed by "Windows 7 (loader) on /dev/sda1" and "Windows 7 (loader) on /dev/sdb1". I eventually removed Recovery Mode, Other Versions, and Memtest. Now, when I run: sudo update-grub I get this print-out: Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.2.0-26-generic Found initrd image: /boot/initrd.img-3.2.0-26-generic Found Windows 7 (loader) on /dev/sda1 Found Windows 7 (loader) on /dev/sdb1 I would like to remove "Windows 7 (loader) on /dev/sda1", as it is a broken entry that shouldn't exist, and must have been installed during my first Windows 7 attempt. I cannot find a Windows 7 entry in /etc/grub.d... And I don't know where to look. Here is a layout of my hard drives: /dev/sda1/ (1.82 TiB), NTFS ("Media") /dev/sdb1/ (100 Mib), NTFS ("System Reserved") /dev/sdb2/ (149 GiB), NTFS ("Windows 7") /dev/sdb3/ (149 GiB), Extended (" ") /dev/sdb4/ (145 GiB), ext4 (" ") /dev/sdb5/ (4 GiB), linux-swap (" ") /dev/sdc1/ (488.28 GiB), NTFS ("Downloads") /dev/sdc2/ (488.28 GiB), NTFS ("AltMedia") /dev/sdc3/ (886.45 GiB), NTFS ("Personal") unallocated (2.09 MiB), unallocated What I think has happened: Windows 7 installed first and badly. I installed it again. First, there was Windows XP to guide where the bootloader went to so it was put on /dev/sdb1/. But, the second time no such guide existed so the machine put another bootloader on /dev/sda1/. sda1, by the way, is the only partition on a 2TB drive. No boot record partition appears to exist according to gedit. I'm not sure where Grub2 is getting this information from. But, there it is. Is there anything somebody can do to help me? Or, is there any more information I should add? Thank you, community!

    Read the article

  • Triple boot WIndows 7, Windows 8, and Mountain Lion on Macbook Pro

    - by Nathan
    Ok, So I have a bit of a unique situation here I could use some help on. I've modded my summer 2011 MBPro to have 2 harddrives by replacing the optical drive. OSX Mountain Lion is installed on a single partition of a 120GB SSD. The second drive is 750GB, partitioned as 550GB, 150GB, and ~50GB. I've set the 550GB to act as my OSX homefolder, but I'd like to install windows 7 and Windows 8 on the remaining partitions. It Took a while, but by following this guide, I eventually found a way to install Windows without a CD/DVD drive by following this http://huguesval.com/blog/2012/02/installing-windows-7-on-a-mac-without-superdrive-with-virtualbox/ It worked flawlessly for creating both windows 7 and windows 8 images that I could clone onto FAT32 partitions. However, I have encountered a problem when trying to triple boot. After I put Windows 8 onto the ~50GB partition and tried to boot into windows 7 I get an error that says something like: error: 0x0000000e The Boot selection failed because the required device is inaccessible. If I re-clone the windows 7 image onto the drive and select the option to "replace BCD" file for the drive, windows 7 will boot but windows 8 now gives me the same exact error. I realize this is a pretty extensive setup, but if anyone has some insight I'd love to hear it.

    Read the article

  • Mobile Friendly Websites with CSS Media Queries

    - by dwahlin
    In a previous post the concept of CSS media queries was introduced and I discussed the fundamentals of how they can be used to target different screen sizes. I showed how they could be used to convert a 3-column wide page into a more vertical view of data that displays better on devices such as an iPhone:     In this post I'll provide an additional look at how CSS media queries can be used to mobile-enable a sample site called "Widget Masters" without having to change any server-side code or HTML code. The site that will be discussed is shown next:     This site has some of the standard items shown in most websites today including a title area, menu bar, and sections where data is displayed. Without including CSS media queries the site is readable but has to be zoomed out to see everything on a mobile device, cuts-off some of the menu items, and requires horizontal scrolling to get to additional content. The following image shows what the site looks like on an iPhone. While the site works on mobile devices it's definitely not optimized for mobile.     Let's take a look at how CSS media queries can be used to override existing styles in the site based on different screen widths. Adding CSS Media Queries into a Site The Widget Masters Website relies on standard CSS combined with HTML5 elements to provide the layout shown earlier. For example, to layout the menu bar shown at the top of the page the nav element is used as shown next. A standard div element could certainly be used as well if desired.   <nav> <ul class="clearfix"> <li><a href="#home">Home</a></li> <li><a href="#products">Products</a></li> <li><a href="#aboutus">About Us</a></li> <li><a href="#contactus">Contact Us</a></li> <li><a href="#store">Store</a></li> </ul> </nav>   This HTML is combined with the CSS shown next to add a CSS3 gradient, handle the horizontal orientation, and add some general hover effects.   nav { width: 100%; } nav ul { border-radius: 6px; height: 40px; width: 100%; margin: 0; padding: 0; background: rgb(125,126,125); /* Old browsers */ background: -moz-linear-gradient(top, rgba(125,126,125,1) 0%, rgba(14,14,14,1) 100%); /* FF3.6+ */ background: -webkit-gradient(linear, left top, left bottom, color-stop(0%,rgba(125,126,125,1)), color-stop(100%,rgba(14,14,14,1))); /* Chrome,Safari4+ */ background: -webkit-linear-gradient(top, rgba(125,126,125,1) 0%, rgba(14,14,14,1) 100%); /* Chrome10+,Safari5.1+ */ background: -o-linear-gradient(top, rgba(125,126,125,1) 0%, rgba(14,14,14,1) 100%); /* Opera 11.10+ */ background: -ms-linear-gradient(top, rgba(125,126,125,1) 0%, rgba(14,14,14,1) 100%); /* IE10+ */ background: linear-gradient(top, rgba(125,126,125,1) 0%, rgba(14,14,14,1) 100%); /* W3C */ filter: progid:DXImageTransform.Microsoft.gradient( startColorstr='#7d7e7d', endColorstr='#0e0e0e',GradientType=0 ); /* IE6-9 */ } nav ul > li { list-style: none; float: left; margin: 0; padding: 0; } nav ul > li:first-child { margin-left: 8px; } nav ul > li > a { color: #ccc; text-decoration: none; line-height: 2.8em; font-size: 0.95em; font-weight: bold; padding: 8px 25px 7px 25px; font-family: Arial, Helvetica, sans-serif; } nav ul > li a:hover { background-color: rgba(0, 0, 0, 0.1); color: #fff; }   When mobile devices hit the site the layout of the menu items needs to be adjusted so that they're all visible without having to swipe left or right to get to them. This type of modification can be accomplished using CSS media queries by targeting specific screen sizes. To start, a media query can be added into the site's CSS file as shown next: @media screen and (max-width:320px) { /* CSS style overrides for this screen width go here */ } This media query targets screens that have a maximum width of 320 pixels. Additional types of queries can also be added – refer to my previous post for more details as well as resources that can be used to test media queries in different devices. In that post I emphasize (and I'll emphasize again) that CSS media queries only modify the overall layout and look and feel of a site. They don't optimize the site as far as the size of the images or content sent to the device which is important to keep in mind. To make the navigation menu more accessible on devices such as an iPhone or Android the CSS shown next can be used. This code changes the height of the menu from 40 pixels to 100%, takes off the li element floats, changes the line-height, and changes the margins.   @media screen and (max-width:320px) { nav ul { height: 100%; } nav ul > li { float: none; } nav ul > li a { line-height: 1.5em; } nav ul > li:first-child { margin-left: 0px; } /* Additional CSS overrides go here */ }   The following image shows an example of what the menu look like when run on a device with a width of 320 pixels:   Mobile devices with a maximum width of 480 pixels need different CSS styles applied since they have 160 additional pixels of width. This can be done by adding a new CSS media query into the stylesheet as shown next. Looking through the CSS you'll see that only a minimal override is added to adjust the padding of anchor tags since the menu fits by default in this screen width.   @media screen and (max-width: 480px) { nav ul > li > a { padding: 8px 10px 7px 10px; } }   Running the site on a device with 480 pixels results in the menu shown next being rendered. Notice that the space between the menu items is much smaller compared to what was shown when the main site loads in a standard browser.     In addition to modifying the menu, the 3 horizontal content sections shown earlier can be changed from a horizontal layout to a vertical layout so that they look good on a variety of smaller mobile devices and are easier to navigate by end users. The HTML5 article and section elements are used as containers for the 3 sections in the site as shown next:   <article class="clearfix"> <section id="info"> <header>Why Choose Us?</header> <br /> <img id="mainImage" src="Images/ArticleImage.png" title="Article Image" /> <p> Post emensos insuperabilis expeditionis eventus languentibus partium animis, quas periculorum varietas fregerat et laborum, nondum tubarum cessante clangore vel milite locato per stationes hibernas. </p> </section> <section id="products"> <header>Products</header> <br /> <img id="gearsImage" src="Images/Gears.png" title="Article Image" /> <p> <ul> <li>Widget 1</li> <li>Widget 2</li> <li>Widget 3</li> <li>Widget 4</li> <li>Widget 5</li> </ul> </p> </section> <section id="FAQ"> <header>FAQ</header> <br /> <img id="faqImage" src="Images/faq.png" title="Article Image" /> <p> <ul> <li>FAQ 1</li> <li>FAQ 2</li> <li>FAQ 3</li> <li>FAQ 4</li> <li>FAQ 5</li> </ul> </p> </section> </article>   To force the sections into a vertical layout for smaller mobile devices the CSS styles shown next can be added into the media queries targeting 320 pixel and 480 pixel widths. Styles to target the display size of the images in each section are also included. It's important to note that the original image is still being downloaded from the server and isn't being optimized in any way for the mobile device. It's certainly possible for the CSS to include URL information for a mobile-optimized image if desired. @media screen and (max-width:320px) { section { float: none; width: 97%; margin: 0px; padding: 5px; } #wrapper { padding: 5px; width: 96%; } #mainImage, #gearsImage, #faqImage { width: 100%; height: 100px; } } @media screen and (max-width: 480px) { section { float: none; width: 98%; margin: 0px 0px 10px 0px; padding: 5px; } article > section:last-child { margin-right: 0px; float: none; } #bottomSection { width: 99%; } #wrapper { padding: 5px; width: 96%; } #mainImage, #gearsImage, #faqImage { width: 100%; height: 100px; } }   The following images show the site rendered on an iPhone with the CSS media queries in place. Each of the sections now displays vertically making it much easier for the user to access them. Images inside of each section also scale appropriately to fit properly.     CSS media queries provide a great way to override default styles in a website and target devices with different resolutions. In this post you've seen how CSS media queries can be used to convert a standard browser-based site into a site that is more accessible to mobile users. Although much more can be done to optimize sites for mobile, CSS media queries provide a nice starting point if you don't have the time or resources to create mobile-specific versions of sites.

    Read the article

  • Create a Shortcut to Put Your Windows Computer into Hibernation

    - by Mysticgeek
    Putting your Windows computer into Hibernation Mode allows you to save power, and quickly access your desktop again when you need it. Here we show how to create a shortcut to put your PC in Hibernation Mode quickly. Note: Here we show how to create the shortcut in Windows 7 and add it to the Taskbar. But creating the shortcut should work in XP and Vista as well. Create Shortcut  Right-click an empty area on your desktop and select New \ Shortcut from the Context Menu. In the Create Shortcut window type or copy the following in the location field… C:\Windows\System32\rundll32.exe powrprof.dll, SetSuspendState 0,1,0 Now give the shortcut a name such as Hibernate Computer or whatever you want to call it. Now you have the shortcut on your desktop, but you might want to change the icon to something else. Change Shortcut Icon Right-click the shortcut icon and select Properties. Select the Shortcut Tab and click the Change Icon button. In the Look for icons in this file field copy and past the following then click OK. %SystemRoot%\system32\SHELL32.dll This brings up a list of included Windows icons you can choose from. Select whatever you want it to be. There are a couple of Power icons in the directory…click OK. Of course you can choose any icon you want, if you customize your icons just browse to the directory they are in. For more on selecting icons check out our article on how to customize your icons in Windows 7 or how to change a file type’s icon. Now you will see the icon in the Shortcut Properties window, click OK. Here we have a nice looking shortcut that you can use to put your machine into Hibernation. Or here we used a customized Star Trek icon just to make things more interesting… You can pin the shortcut to the Taskbar for easy access. Conclusion If Hibernation is not enabled on your Windows 7 system you can easily manage it. By creating a shortcut and pinning to the Taskbar, it allows you to put your machine into Hibernation Mode quick and easy. If you like to customize your desktop with unique icons check out our posts on a Sci-Fi icon pack or Video Game icon pack. Similar Articles Productive Geek Tips Create a Shortcut for Locking Your Computer Screen in Windows 7 or VistaCreate Shutdown / Restart / Lock Icons in Windows 7 or VistaHow To Manage Hibernate Mode in Windows 7Microsoft Releases Pre-SP1 Updates for Windows VistaCreate a Shortcut or Hotkey to Run CCleaner Silently TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 10 Superb Firefox Wallpapers OpenDNS Guide Google TV The iPod Revolution Ultimate Boot CD can help when disaster strikes Windows Firewall with Advanced Security – How To Guides

    Read the article

  • Error codes 80070490 and 8024200D in Windows Update

    - by Sammy
    How do get past these stupid errors? The way I have set things up is that Windows Update tells me when there are new updates available and then I review them before installing them. Yesterday it told me that there were 11 new updates. So I reviewed them and I saw that about half of them were security updates for Vista x64 and .NET Framework 2.0 SP2, and half of them were just regular updates for Vista x64. I checked them all and hit the Install button. It seemed to work at first, updates were being downloaded and installed, but then at update 11 of 11 total it got stuck and gave me the two error codes you see in the title. Here are some screenshots to give you an idea of what it looks like. This is what it looks like when it presents the updates to me. This is how it looks like when the installation fails. I'm not sure if you're gonna see this very well but these are the updates it's trying to install. Update: This is on Windows Vista Ultimate 64-bit with integrated SP2, installed only two weeks ago on 2012-10-02. Aside from this, the install is working flawlessly. I have not done any major changes to the system like installing new devices or drivers. What I have tried so far: - I tried installing the System Update Readiness Tool (the correct one for Vista x64) from Microsoft. This did not solve the issue. Microsoft resource links: Solutions to 80070490 Windows Update error 80070490 System Update Readiness Tool fixes Windows Update errors in Windows 7, Windows Vista, Windows Server 2008 R2, and Windows Server 2008 Solutions to 8024200D: Windows Update error 8024200d Essentially both solutions tell you to install the System Update Readiness Tool for your system. As I have done so and it didn't solve the problem the next step would be to try to repair Windows. Before I do that, is there anything else I can try? Microsoft automatic troubleshooter If I click the automatic troubleshooter link available on the solution web page above it directs me to download a file called windowsupdate.diagcab. But after download this file is not associated to any Windows program. Is this the so called Microsoft Fix It program? It doesn't have its icon, it's just blank file. Does it need to be associated? And to what Windows program?

    Read the article

  • How to boot windows 8 in a dual boot along with windows 7?

    - by GoldDove
    I have installed a WIndows 8 evaluation about a week ago. Usually, it asks me every time I turn on my computer whether to boot into windows 8 or windows 7. The default was windows 8 after 30 seconds. I changed that just yesterday to be default windows 7 after 5 seconds. And after I changed the setting, I went ahead and went into windows 8 and did my work. Today, when I turned on my computer, it is failing to ask me which one to boot it in. It simply boots directly into Windows 7. Is there any reason for this? Can I no longer boot into Windows 8?

    Read the article

  • Transferring a Windows 8 license and proper un- and reinstallation

    - by Kiwi
    Long story short I have two computers: a laptop and a desktop computer. Both have Windows 7 on them. I buy the Windows 8 Pro upgrade. To see if it screws up anything, I install it on my laptop as a guinea pig. I intend to use Windows 8 for my main computer, my desktop, but I want to test it on the laptop, so I know I don’t risk losing access to my desktop and the data on it. I never use my laptop, and only used it, because it already has a Windows 7 installation on it. The problem At some point, I must have entered the license key on my laptop, because when I go to the activation screen on my desktop, I get this: Uh-oh. I can’t use the key on my desktop. Now how the hell do I transfer the key from my laptop to my desktop computer? Answers and suggestions so far Let’s just say that I tried everything possible to get some answers on this matter. The best response I got from Microsoft is this: To install Windows 8 on your desktop, do the following: Uninstall Windows 8 on your laptop Afterwards, install Windows 8 on your desktop If it won’t activate, call product activation at (...) I am not a fan of that last point. The error message does allude to such a solution, however: If you’ve reinstalled Windows or made changes to your hardware recently, you may be able to use your current key. The question My main question is this: has anyone been in a similar situation, and if so, what did you do to resolve this? Failing that, what is the proper way to uninstall the Windows 8 installation on my laptop, and reinstall the Windows 8 installation on my desktop? Ad 1 I have already tried using the “reset” feature on my laptop, but that only resulted in a new Windows 8 installation that was already activated. But which is the right way to uninstall the installation in a way that allows me to use the license key on the desktop computer? Ad 2 Which is the proper way to reinstall the Windows 8 installation on my desktop computer? Why do I even have to reinstall it in the first place? I won’t get around to do this, until my USB key with 3.0 support arrives in the mail, but it is going to be a while, until I find a assuaging response to the best way to go about this anyway.

    Read the article

  • Which Windows 8 edition should I update to from Windows 7 Home Premium?

    - by Max
    I have Windows 7 Home Premium on my laptop, need to upgrade to Windows 8. If there were a Windows 8 Home Premium midway between those two I would've chosen that... but there are only two Windows 8 or Windows 8 Pro, so I'm a bit confused, as I don't want the former to be like Windows 7 Basic. My usage is mostly coding, game development, mid-performance gaming and some benchmarking and video editing. Your recommendations please?

    Read the article

  • How to boot windows 8 in a dual boot along with windows 7? [migrated]

    - by GoldDove
    I have installed a WIndows 8 evaluation about a week ago. Usually, it asks me every time I turn on my computer whether to boot into windows 8 or windows 7. The default was windows 8 after 30 seconds. I changed that just yesterday to be default windows 7 after 5 seconds. And after I changed the setting, I went ahead and went into windows 8 and did my work. Today, when I turned on my computer, it is failing to ask me which one to boot it in. It simply boots directly into Windows 7. Is there any reason for this? Can I no longer boot into Windows 8?

    Read the article

  • Update Metadata and Cover Art in Windows Media Player 12

    - by DigitalGeekery
    If you use Windows Media Player 12 in Windows 7, you may notice some of your media is missing information when displayed in the library. Today we look at how to edit and update metadata and cover art in WMP 12. By default, Windows Media Player will pull metadata, such as the title, artist, album, and cover art from the Internet. If you did not accept that default option during setup, we’ll need to turn the feature on first. Select Tools > Options from the top Menu bar. On the Library tab, ensure that Retrieve additional information form the Internet is checked. Click OK. Editing Metadata Now we’re ready to update some files. Find a media file with incorrect details or cover art. Right-click on the title and select Find album info. This will bring up the Find album information window. Here you’ll see the existing information that Windows Media Player interpreted as correct on the left side. The results of  WMP’s search for the media information are on the right. Click on Artists,  Albums , or Tracks to scroll through the search results and try to find a match. You can also type in new keywords in the Search box and hit enter (or click the Search button) to perform a new search.   If you find a correct match for your media file, click to select it and click Next. You’ll be prompted to confirm your selection, then click Finish. You should now see your media file displayed properly in Windows Media Player. Manually Entering Metadata If your search for the correct media information comes up empty, you can always manually enter the information yourself. On the Find album information window, click Edit under Existing Information. You can edit the existing information in the text boxes or the Genre dropdown box. There are a couple hidden text boxes below. Click next to Contributing Artist or Composer to enter that information.   Choosing Your Own Cover Art If your media file doesn’t pull the proper cover art, or if you simply wish to find a different image, you can add your own. Search online for a suitable image. An ideal size would be around 300 x 300 pixels, give or take. Right-click on the image copy the image. You’ll need to switch to Expanded title (if you haven’t already) to paste the image.   Paste your new image by right-clicking on the current image and select Paste album art. Note: If the image is not suitable size or type, the Paste album art option will not be available. Your new cover art will appear in Windows Media Player.   Even though it is pulled from the Internet, cover art is cached on your computer and will still be available when you are disconnected from the Internet. Are you new to Windows Media Player? If so, check out our article on how to Manage your music with Windows Media Player. Similar Articles Productive Geek Tips Make VLC Player Look like Windows Media Player 11Fixing When Windows Media Player Library Won’t Let You Add FilesMake VLC Player Look like Windows Media Player 10Add Images and Metadata to Windows 7 Media Center Movie LibraryMake VLC Player Look like Winamp 5 (Kinda) TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

    Read the article

  • Create Music Playlists in Windows 7 Media Center

    - by DigitalGeekery
    One of the new features in Windows 7 Media Center is the ability to easily create music playlists without using Media Player. Today we’ll take a closer look at how to create them directly in Media Center. Create Manual Playlists Open Windows Media Center and select the Music Library. From within the Music Library, choose playlists from the top menu.   Then select Create Playlist. Give your new playlist a name, and select Next. Choose Music Library and select Next.    Select “songs” from the top menu, choose the songs for your playlist from your library, and select Next when finished. You can also click Select All to add all songs to your playlist, or clear all to remove them. Note: you can also sort by artist, album, genre, etc. from the top menu.   Now you can review and edit your playlist. Click the up and down pointers to move songs up and down in the playlist, or “X” to remove them. You can also go back and add additional songs by selecting Add More. Click Create when you are finished.   Auto Playlists Windows Media Center also allows you to create six different auto playlists. These are dynamic playlists based on pre-defined criteria. Auto Playlists include All Music, Music added in the last month, Music auto rated at 5 stars, Music played in the last month, Music played the most, and Music rated 4 or 5 stars. These Auto Playlists will change dynamically as your library and listening habits change. Your new music playlists can be found under playlists in the music library. Select play playlist to start the music. Now kick back and enjoy the music from your playlist. Conclusion While earlier versions of WMC allowed you to create playlists, you had to do it through Windows Media Player. This is a nice new feature for music lovers who use WMC and prefer to do everything with a remote. Do you already have playlists that you’ve created in Windows Media Player? Windows Media Center can play those too. If your playlists are in the default Music folder, Media Center will detect them automatically and add them to your Music Library. Plus, any playlists you create in Media Center are also available for Media Player. For more on creating Playlists in Media Player, check out our previous articles on how to create a custom playlist in Windows Media Player 12, and how to create auto playlists in WMP 12. Similar Articles Productive Geek Tips How To Rip a Music CD in Windows 7 Media CenterCreate Custom Playlists in Windows Media Player 12Using Netflix Watchnow in Windows Vista Media Center (Gmedia)How to Create Auto Playlists in Windows Media Player 12Fixing When Windows Media Player Library Won’t Let You Add Files TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials 21 Cursor Packs for XP, Vista & 7 Map the Stars with Stellarium

    Read the article

  • Make Text and Images Easier to Read with the Windows 7 Magnifier

    - by DigitalGeekery
    Do you have impaired vision or find it difficult to read small print on your computer screen? Today, we’ll take a closer look at how to magnify that hard to read content with the Magnifier in Windows 7. Magnifier was available in previous versions of Windows, but the Windows 7 version comes with some notable improvements. There are now three screen modes in Magnifier. Full Screen and Lens mode, however, require Windows Aero to be enabled. If your computer doesn’t support Aero, or if you’re not using am Aero theme, Magnifier will only work in Docked mode. Using Magnifier in Windows 7 You can find the Magnifier by going to Start > All Programs > Accessories > Ease of Access > Magnifier.   Alternately, you can type magnifier into the Search box in the Start Menu and hit Enter. On the Magnifier toolbar, choose your View mode by clicking Views and choosing from the available options. Clicking the plus (+) and minus (-) buttons will zoom in or zoom out. You can change the zoom in/out percentage by adjusting the slider bar. You can also enable color inversion and select tracking options. Click OK when finished to save your settings.   After a brief period, the Magnifier Toolbar will switch to a magnifying glass icon. Simply click the magnifying glass to display the Magnifier Toolbar again.   Docked Mode In Docked mode, a portion of the screen is magnified and docked at the top of the screen. The rest of your desktop will remain in it’s normal state. You can then control which area of the screen is magnified by moving your mouse.   Full Screen Mode This magnifies your entire screen and follows your mouse as you move it around. If you loose track of where you are on the screen, use the Ctrl + Alt + Spacebar shortcut to preview where your mouse pointer is on the screen.   Lens Mode The Lens screen mode is similar to holding a magnifying glass up to your screen. Full screen mode magnifies the area around the mouse. The magnified area moves around the screen with your mouse.    Shortcut Keys Windows key + (+) to zoom in Windows key + (-) to zoom out Windows key + ESC to exit Ctrl + Alt + F – Full screen mode Ctrl + Alt + L – Lens mode Ctrl + Alt + D – Dock mode Ctrl + Alt + R – Resize the lens Ctrl + Alt + Spacebar – Preview full screen Conclusion Windows Magnifier is a nice little tool if you have impaired vision or just need to make items on the screen easier to read. Similar Articles Productive Geek Tips New Features in WordPad and Paint in Windows 7How-To Geek on Lifehacker: How to Make Windows Vista Less AnnoyingUsing Comments in Word 2007 DocumentsMake Your PC Look Like Windows Phone 7Use Image Placeholders to Display Documents Faster in Word TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer XPS file format & XPS Viewer Explained Microsoft Office Web Apps Guide

    Read the article

  • What's Microsoft's strategy on Windows CE development?

    - by Heinzi
    Lots of specialized mobile devices use Windows CE or Windows Mobile. I'm not talking about smart phones here -- I know that Windows Phone 7 is Microsoft's current technology of choice here. I'm talking about barcode readers, embedded devices, industry PDAs with specialized hardware, etc... the kind of devices (Example 1, Example 2) where Windows Phone Silverlight development is not an option (no P/Invoke to access the hardware, etc.). Since direct Compact Framework support has been dropped in Visual Studio 2010, the only option to develop for these device currently is to use outdated development tools (VS 2008), which already start to cause trouble on modern machines (e.g. there's no supported way to make the Windows Mobile Device Emulator's network stack work on Windows 7). Thus, my question is: What are Microsoft's plans regarding these mobile devices? Will they allow native applications on Windows Phone, such that, for example, barcode reader drivers can be developed that can be accessed in Silverlight applications? Will they re-add "native" Compact Framework support to Visual Studio and just haven't found the time yet? Or will they leave this niche market?

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >