Search Results

Search found 9611 results on 385 pages for 'low power'.

Page 101/385 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• Why such a dramatic difference in wireless router max. simultaneous connections?

  - by Jez

  Recently, I've needed to look into buying a wireless router for a mission-critical system at work that will need to support quite a few simultaneous connections (potentially a few hundred laptops). One thing I've noticed is that there seems to be a dramatic difference between the max. simultaneous connections different routers can support; see this page for example - anything from 32 to 35,000! Why is there this degree of difference? You'd have thought that if we know how to make routers that can handle thousands of connections, we wouldn't be making stuff that's limited to a pathetic 32 anymore. Is it a firmware thing? A hardware thing? Are low-end manufacturers purposely putting low arbitrary connection limits in so people can be "encouraged" to pay more for high-end routers?

  Read the article

• DSL to web connectivity is often lost

  - by broiyan

  I am experiencing a frequent web connectivity problem via a DSL modem. The problem usually shows up as a reload later screen inside of Google Chrome, as illustrated. My DSL service was fine for the first 2 months, but in the most recent month this problem has been occurring. I have this problem several times a day. A few weeks ago, I used to power cycle (off then on) the DSL modem but this usually did not solve the problem. However, in recent days, the power cycle does seem to fix the problem. When the problem occurs, the modem lights do not look unusual. All the lights are green or flashing green. This problem happens regardless of whether I am using ethernet or WiFi for the last few meters between the DSL modem and the computer. What is the likely cause? How can I help the phone company solve this? Their staff are not very effective at troubleshooting this.

  Read the article

• How do laptop battery voltages affect runtime?

  - by Bigbio2002

  I ordered a new battery for my faithful XPS M1710. I'm not sure of the voltage of the battery I have now, but the new one that the Dell rep got me (after 3-4 times confirming my phone number and laptop model number) is 14.8v. I was a bit concerned about potential incompatibilities (as most of the other compatible batteries listed were 11.1v), but I figure that there's no way that Dell would "recommend" batteries that wouldn't work or fry your system. Now, my question is, how does voltage affect battery life? If we assume the needed power draw to be constant, a higher voltage would indicate less amperage needed, therefore the battery would last longer before running out, yes? Or am I missing something? For reference: P=I*V P = power I = current V = voltage (duh)

  Read the article

• Dark Windows 7 Screen

  - by user147521

  My Gateway laptop -Windows 7- screen became too dark a few days ago after I finished installing Windows automatic update. I can see nothing unless I use a flashlight. Windows login screen is the only bright screen for few seconds. What should I do to resolve this issue? I checked power-saving/ Power Options settings and rebooting in Safe Mode. I tried to lower the refresh rate but it did not allow me. The laptop adapter type is ATI Radeon Xpress series. I uninstalled and reinstalled the driver. And the driver is up to-date. Any help would be appreciated.

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• How do I pick a motherboard?

  - by EpsilonVector

  When building your own computer one part was always a mystery to me: the motherboard. Picking a CPU/GPU/memory is easy- you just figure out where the various chips are in the low end to high end scale, do a little market research on what current games demand, and pick the parts from their respective continuums of low-to-high-end models. A mother board is more complicated though. Its features are not as obvious as "this motherboard is faster than that motherboard". Now you need to deal with part compatibilities, bus speeds, maybe power management stuff, etc. I'm interested in a short guide for selecting a motherboard, especially- what pitfalls to avoid (for example, can bus speed become a bottleneck?). To clarify: I'm not looking for motherboard recommendations. I'm looking for guidance regarding how to evaluate the fitness of a motherboard given the rest of the computer parts.

  Read the article

• Windows 7: Use VirtualStore technology as user for own benefit?

  - by mfn

  I've researched a bit and came to the understanding that VirtualStore is part of the new UAC feature in Vista/W7 which is the file system part of the transparent data redirection and redirects write access to folders like program files to C:\User\<username>\AppData\Local\VirtualStore\ in lack of applications respecting the LUA principles. Now I'm interested if that kind of transparent redirection can also be used as a power to the user. Here's an example which comes to my mind: I install any kind of software to e.g. D:\Whatever\ThisAndThisApp\ and I set up things that, after initial installation, any write access to this folder is transparently redirected to e.g. D:\MyOwnVirtualStore\Whatever\ThisAndThisApp\file_only_writable_here.txt. Is this thinking too far or can I actually use that power of VirtualStore as a user on Windows 7? I'm using the Professional version of that matters.

  Read the article

• Complete machine freezes...at a loss

  - by user28818

  Guys, We built around 12 machines a few months ago to run Ubuntu. They each have the following specs: ASUS Z8NA-D6 motherboard Dual quad core Intel(R) Xeon(R) CPU E5520 @ 2.27GHz OCZ Mod Extreme Pro 500W power supply 12 GB Kingston RAM Nvidia GeForce 9800 GT graphics card My machine ran well for awhile. However, it started experiencing random lockups. These lockups are not X lockups, they are complete system freezes. The nic stops responding, the magic sysrq buttons won't work. The machine is dead. I first suspected RAM. Memtest86 didn't find anything, but I replaced the RAM anyway. Still, lockups. So I replaced the graphics card. Still, more lockups. They became more and more frequent and started to happen 2-3 times a day. So I replaced the motherboard and power supply in one fell swoop. Suddenly, no more lockups! Woohoo! Except, a week later, in the morning, the machine wouldn't wake up. I reset it, started it up, and the log files showed the last entry at around 11 pm the evening before. This has started occurring with more frequency...now just about every morning I come in, the machine is locked up, and has been since the night before. Yesterday, in the 3 weeks since I replaced the motherboard and power supply, the machine actually locked up on in in mid-work. This is the first time since replacing the two (MB and PS) that this happened while I was using it. All others occurred while I was away. I'm at a loss. Nothing is in syslog or message that would indicate a problem around the time of the lockup. Temps are good...I use lmsensors to monitor and have a script that writes the output to file every minute. They never get that high. The only thing I haven't replaced at this point is the case and the harddrives. I doubt either could be the cause. What would you do if you were in my shoes? Is there a troubleshooting approach I'm missing? For the record, all of the other machines, all eleven of them, don't have any problems. They're all running the same version of Ubuntu (Lucid) that I am. Thanks!

  Read the article

• PC Speaker sounds when machine locks up.

  - by d.c

  What would cause my PC speaker to sound a low frequency continuous tone as my system locks up? Generally what will happen is I'll notice the application I'm using will stop responding but explorer will be partially responsive, then after a few more actions explorer stops responding, and the last click will cause the pc speaker to emit a low constant tone as the machine locks up completely. The only resolve at that point is to restart. Its not a thermal issue, I'm reading the cpu, and hdd temps with software and hardware monitors. AV and malware scans come up clean. I've swapped out my ram, reseated all my components. Used sfc with no results. chkdisk locks up at 3% and defragmenting does the same, but I can read the drive without trouble (I know this as I've done av/malware scans and I also backed everything up since this started happening) I'm mostly just interested to learn, if anyone knows, why the pc speaker would sound during the lock up. windows xp sp2

  Read the article

• iPad USB Charging Utility for Dell Optiplex

  - by BreakPhreak

  As you probably know already, an iPad requires a certain power on USB port to be charged from. Thus, some motherboard manufacturers (such as ASUS, Gigabyte etc) had released a special driver that recognizes that an iPad is connected to the port and adjust the USB power accordingly. On one of my computers (Gigabyte motherboard) it works fine. But other one is Dell Optiplex 780 and the regular googling by "<motherboard type> + iPad charging" doesn't seem to bring encouraging results. Just for completeness: no, the iPad is not being charged without any special driver installed (out of the box) either. Any suggestions will be welcomed.

  Read the article

• SBS 2008 reinstall on new machine

  - by Jon

  We purchased a single license on Windows Small Business Server 2008 for a medical office, and soon after a power fault caused the server to overload, destroying the power supply and motherboard. I reinstalled on a new server, and have the domain up and running again, but under system properties it tells me I still need to activate windows, and that the product key currently entered is invalid for activation. I've been trying to figure out how to get in touch with Microsoft to explain the situation and get a new activation key issued without having to pay for another license which we can't afford, but the online documentation hasn't been particularly clear on the subject. Does anyone know how to do that, or if I do need the activation key to continue using SBS 2008? (It currently tells me I have 56 days left to activate) Any tips would be appreciated. I'm not strictly a computer guy and I'm feeling a little lost.

  Read the article

• PC won't boot with 4 prong CPU connector connected. Motherboard or CPU dead - which one? Both?

  - by scrot

  In the middle of use, my computer shut down. I tried to turn it on but it maybe comes on for half a second, shuts down, then flickers again very quickly about 2 seconds later before giving up completely. So I took everything apart and nailed it down to the power supply, the mobo, or the CPU. I had an extra old power supply around, hooked that up and it had the same problems, so that can't be it. When the 4 prong CPU connector is not connected, the motherboard 'functions' in that it stays on and runs the heat sink etc. Throw in the 4 prong connector and that's when it doesn't stay on. So it must be the CPU, right? Motherboard: ASUS P6X58D CPU: Intel i7-920 Bot are under warranty (supposedly) - should I get both replaced or what?

  Read the article

• plugging in a 3.3V 50pin laptop HDD to USB?

  - by barlop

  I have a 50pin laptop hard drive. 1.8" wide. This 50pin connector concerns me.. Even if I get an adaptor, How can I know which side of the connector takes the power? I don't want to plug it in the wrong way. And I don't have n adaptor.. Could people link me to adaptors too. but main question is, which side to plug it in when I get the adaptor. I want to be sure. I do not want to blow the hdd. For the 3.3V I have a plan. Connecting green and black and using the orange cable(3.3v) to feed power. I am not too worried about that bit. But as I said.. Main thing is I want to know which side is 3.3V hard drive is MK6006GAH

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• further troubleshooting on a p8z77 motherboard

  - by Journeyman Geek

  I just bought a brand now asus p8z77 motherboard with a intel 3770. Its currently not booting - the system powers up for half a second and then powers down, and the CPU error light shines. I've tried switching ram between slots, switching PSUs, updating the bios (which can be done sans processor or ram on this model). Power: The 8 pin power connector is definitely in place correctly, and I've tried swapping PSUs between a new seasonic m12, and a known good cheapie PSU Ram: Ram is in the recommended slot for single stick operation, and tried swapping between the two sticks of DDR3 I have. Processor: Its installed correctly as far as I can tell, no obvious bent pins on the motherboard. At this point I'm guessing I'll need to RMA something. Are there any 'definitive' tests I can try, short of swapping CPU and motherboard that would let me know it is the CPU? Can I actually trust the error light on the motherboard?

  Read the article

• Windows Home Server Passwords Do Not Match [closed]

  - by Ben Fulton

  I have a Windows Home Server that chunks along just fine most of the time. I've never bothered to put it on a GPS and so it's vulnerable to power outages that happen a few times a year. This most recent time, it came back and seemed to be fine, but whenever I try to access a shared folder I get "Passwords do not match". They matched before the power went out, and I couldn't update the WHS password since I apparently didn't know the old one. How do I fix this?

  Read the article

• How would I measure the amount of RAM needed per Glassfish domain? [closed]

  - by oligofren

  Possible Duplicate: Can you help me with my capacity planning? In our test environment we have a lot of apps spread out over a few servers and Glassfish domains. To make versioning easier I would have liked to have one Glassfish domain per customer per app (kind of like a heavyweight version of lots of jetty instances). But I have heard that Glassfish is kind of heavy on the resources, and so I would need to measure approximately how many instances would fit in the available RAM. These are low-traffic/low load testing servers, so CPU is not really an issue, though RAM might be. How would I get an approximate measure of how much RAM is needed? This is one Glassfish 3 instance with one heavy EAR application deployed. top? jvmstats? ??

  Read the article

• Autoplay for USB drive keeps popping up

  - by Adam Haile

  I have a Seagate external 2TB USB drive that when I leave it plugged in, the Autoplay dialog asking what to do with the drive pops up about once every 30-60 minutes. No matter how many times I tell it to go away, it keeps coming back. I have tried multiple power supplies, USB cables, and all the USB ports on my machine...but it keeps doing the same thing. Also, this does not happen with the same drive on a different computer. Could this be some power or configuration setting that is causing this? I'm running Windows 7 x64 (the computer it works on is x86)

  Read the article

• Update a DNS to a for a dynamic IP

  - by zobgib

  I want to use my schools connection as a place to host a small webserver but one problem I have run into is anytime my server reboots I am given a new IP inside the schools range. All of the schools IP are public and therefor I can access my computer directly over WAN just via the IP given in ifconfig. I would like to be able to give my computer a dns which is easy enough when I change the Arecords to match the current IP of my computer. The problem is if my computer ever reboots (my school regularly cycles power at night and over holidays) I am assigned a new IP and have to realize it then update the Arecords This is inconvenient and I figure there must be a better way to keep the DNS records updated either via a script or my own BIND server. That way if there is a power cycle I can still access the server via a Domain Name. If you have any direction to point me in it would be much appreciated. I am running Ubuntu 10.04 if that helps :).

  Read the article

• Strange monitor issue - screen goes black after a few seconds

  - by Scott Szretter

  My LCD monitor display is going black (turning off). It's a Samsung SYncMaster 2233 widescreen. I am trying to figure out if there is anything I can do about it, or if the monitor is junk. I have tried multiple computers, all have the same issue. I have tried a different vga cable, same issue. Power and video cables are tight / double checked. When I power on the monitor, the blue light turns on at the bottom. Then a second or two later the video comes up as expected and it looks fine. However, about 2-3 seconds after that, the screen goes black. The blue light is still on and solid at the bottom (blue light normally flashes when the monitor is sleeping). If I power cycle the monitor, same thing happens. With no computer connected or when I unplug the vga cable, I see the searching for signal message "digital", then the screen goes black. However it usually shows "digital" then "analog" after that and switches between the two a few times. The buttons on the side do not do anything, although they may be, I just can not see if they are or not. I can usually get the "digital" message by pressing the buttons on the side, but then it quickly goes black again. What is really strange is sometimes I can get it to work fine. I am not sure what the difference is. Last week I connected it up and it worked fine and it stayed fine for at least a week! I did not turn it off or anything, I just let the OS put the display to sleep. Then this week one morning I started having the screen going black issue again. Seems like something is either loose inside or beginning to fail. Do you think there is any hope for it? update: pushing the input select button causes the "digital" and "analog" messages to flash on the screen, but only for a few seconds then it goes black. When it was working properly, those messages would flash back and fourth for probably 10-20 seconds then a message would show saying check input signal, but now just a black screen.

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Windows 7: Use VirtualStore as user for own benefit?

  - by mfn

  I've researched a bit and came to the understanding that VirtualStore is part of the new UAC feature in Vista/W7 which is the file system part of the transparent data redirection and redirects write access to folders like program files to C:\User\<username>\AppData\Local\VirtualStore\ in lack of applications respecting the LUA principles. Now I'm interested if that kind of transparent redirection can also be used as a power to the user. Here's an example which comes to my mind: I install any kind of software to e.g. D:\Whatever\ThisAndThisApp\ and I set up things that, after initial installation, any write access to this folder is transparently redirected to e.g. D:\MyOwnVirtualStore\Whatever\ThisAndThisApp\file_only_writable_here.txt. Is this thinking too far or can I actually use that power of VirtualStore as a user on Windows 7? I'm using the Professional version of that matters.

  Read the article

• How is it possible for SSD's drives to have such a good latency?

  - by tigrou

  First time i read some information about SSD's, i was surprised to learn they internally use NAND flash chips. This kind of memory is generally slow (low bandwidth) and have high latency while SSD's are just the opposite. But here is how it works : SSD drives increase their bandwidth by using several NAND flash chips in parallel. In other words, they do some data striping (aka RAID0) across several chips (done by the controller). What i don't understand is how SSD's drives have such a low latency, whereas they are using NAND chips? (or at least lot better than what a typical single NAND chip would do) EDIT: I think under-estimate NAND chip capabilities. USB drives, while powered by NAND's are mostly limited by USB protocol (which have a pretty high latency) and the USB controller. That explain their poor performance in some cases.

  Read the article

• Windows 8 disk errors

  - by wrongusername

  So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >