Search Results

Search found 2852 results on 115 pages for 'thermal paste'.

Page 104/115 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• How do I achieve lossless JPEG joining without truncation of partial MCUs?

  - by Karan

  I am working on a project for which I need to join thousands of JPEG images losslessly (I'm not talking about the Lossless JPEG/JPEG 2000/JPEG-LS formats here). Aforementioned images have varying levels of chroma subsampling (1x1, 1x2, 2x1, 2x2), resulting in varying MCU sizes (8x8, 8x16, 16x8, 16x16 px). However, in any given set of images to be joined together, each image has identical characteristics. For now, let's assume I only have 2 images. Image #1 (I1) is 256x256px in size and #2 (I2) is 239x256px in size. 2x2 subsampling is used such that MCU size is 16x16px. I2 thus obviously has partial MCUs at the right edge, since its width is not evenly divisible by 16. (I've read that so-called 'partial' MCUs actually contain the data for a complete MCU, but the image dimensions instruct the renderer to only display the relevant pixels and ignore/hide the extra ones.) Looking around for tools that could help me accomplish this, I came across a modified version of JpegTran, that contains an experimental lossless crop 'n' drop (cut & paste) feature. All the other apps I encountered that support lossless JPEG editing seem to utilise IJG's (JpegTran) code, so this seemed to be the logical choice. Also, given the sheer number of images, I wanted something that could preferably be run from the command-line so that I could automate the process with a script. Unfortunately, while everything else worked fine, it seems JpegTran truncates the partial MCUs instead of retaining them. Thus in the example above, the final joined image contains all of I1, but only 224x256px of I2. Why 224? because 239 = 14x16+15, which means there are 14 full MCUs along the width, and 1 partial MCU (just 1px short of the complete 16px). The last 15px is what is getting blanked, leading to a 495x256px image with 15px of blank (grey) pixels at the right edge. See images below (shame that imgur re-compresses them): (left )+ (right) = As you can clearly see, the red portion (15px) of I2 has been truncated by JpegTran. If the MCUs were 8px in width, the lost portion would have been the right-most 7px of I2. Similarly, joining I3 (256x239px) *below * I1 would cause the loss of 7 or 15px, depending on the MCU height of course: (top) + (bottom) = If this is better suited to some other StackExchange (or even non-SE) site/forum where JPEG/image encoding experts hang out, do let me know. Can what I am attempting even be done, or is the so-called 'lossless' JPEG crop 'n' drop only valid for images with no partial MCUs? (Maybe that is why the feature is still in an "experimental state" more than a decade after being introduced...) Until I know for sure that it is impossible, I am not interested in suggestions for lossy joining. Avoiding any generational loss whatsoever is the sole reason why I'm breaking my head over this, else I'd have had this done and dusted ages ago. Also, I am not interested in suggestions related to switching image formats. I do not control the source of the images. If it can be done, how? Please keep in mind that any alternate apps suggested must ideally be capable of automation, given the requirements stated above. (But given how it's unlikely I'm even going to receive a useful answer given the constraints, I would be happy with any app suggestion just as long as it actually works. I can always look into an AutoIT/AHK script or something later to automate it.) I understand that an odd-sized final image might cause issues, so I am fully prepared to accept any solution, even if it results in blank (preferably black) padding pixels to the right/bottom. What I mean is, I don't care if I1 + I2 is 496x256px (1px padding) or even 512x256px (17px padding) in size, as long as the final image contains all the actual image data from both source images, and the entire process is lossless. Obviously the lesser the padding (if any), the better, but at this point any solution will do. A Windows-based solution would be perfect, but a Linux-based one would be entirely acceptable.

  Read the article

• How to configure DNS Server on Fedora

  - by user863873

  I want to learn how to configure my home PC server into a web server with domain and host. My IP is 109.99.141.133 and now points to a phpinfo page host on my home server. My registed domain is: anunta-anunturi.ro I searched for a tutorial and I've read that I have to configure /etc/named.conf and the file sources for the new zone that I create. So, from the tutorials, my /etc/named.conf looks like this: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { localhost; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "anunta-anunturi.ro" IN { type master; file "/etc/anunta-anunturi.db"; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; My /etc/anunta-anunturi.db file looks like this — I'm not sure if this is okay, or if it's the easy one. $TTL 86400 anunta-anunturi.ro. IN SOA serveur.anunta-anunturi.ro. root.serveur.anunta-anunturi.ro. ( 1997022700 ; Serial 28800 ; Refresh 14400 ; Retry 3600000 ; Expire 86400 ) ; Minumun IN NS serveur.anunta-anunturi.ro. IN MX 10 mail.anunta-anunturi.ro. serveur.anunta-anunturi.ro. IN A 192.168.1.37 www.anunta-anunturi.ro. IN A 192.168.1.37 mail.anunta-anunturi.ro. IN A 192.168.1.37 Extra info: At home I receive internet from my ISP through a router. My home PC and server recieve their IP automatically from the router when I start/restart. In my local home network, my server receives the IP 192.168.1.37 from the router. When I enter 109.99.141.133 in my browser, it points to the rooter that forwards port 80 to local IP 192.168.1.37 (my home server) Questions: Are my two files good? What/where is my nameserver that I need to copy/paste to my top level domain (where I registered my domain: rotld.ro)?

  Read the article

• Chrome does not re-draw properly on Windows 8

  - by Akshat Mittal

  There are a lot of problems with Chrome (24.0.1312.14 beta || But all this happened before update also) on Windows 8. Problems and explanations are listed below: Google Chrome re-draw time: When I switch tabs, the window retains the content of the previous tab and displays that even if I move my mouse, if only refreshes (re-draws) when there is a change on the webpage (like on hover) or I do a select all (or scroll). One thing to note is that the hover and select happens on the real page and not the retained image-like thing of the older webpage. Chrome is slow and laggy: Websites such as Facebook and Twitter (and more) have gone extremely laggy on Chrome (Win 8). When I was using Windows 7, I never experienced a lag or something. Also when using HTML-5 Websites, the transition (the -webkit-transition in CSS) goes extremely slow at times. Plugins Crash: Plugins like Flash Player, Shockwave Player, and more that are in-built into Chrome Crashes a lot, even when doing simple tasks like playing YouTube Videos, displaying ads or something. Chrome Crashes: Chrome has crashed over 100 times in the past month. Google Chrome just crashes randomly or I don't know the reason. Random Page crashes: Chrome results chrome://crash/(Copy-Paste this in address bar) on random pages even when the page is just loaded, I understand that this can happen on heavy HTML5 or JS websites but what about HTML only websites? Computer Freeze: Chrome sometimes, randomly, freezes my computer. Freeze in the sense, none of the other apps are also working. It's like the whole system freezes, I can not even switch to other apps. I am sure that this is because of Chrome since this happens only when Chrome is active. Most of the things above happens on Super User also, Super User never had any problem when using Chrome on Windows 7. UPDATE 1: @magicandre1981 Commented for trying to disable Hardware Acceleration. I tried it, it somewhat solved the problem but din't fix it. I am still experiencing all the above issues but less frequently (maybe because Chrome Restarted Completely) UPDATE 2: @avirk asked me to try a Stable Version of Chrome and Firefox, I din't experience any lag in Firefox, a little (negligible) lag in Chrome 22 (Maybe because its a new copy of Chrome, I haven't used it much). UPDATE 3: @NothingsImpossible said that He is also experiencing the same problem on Windows Server 2008! This seams to be a major issue now. He also said that GPU load is also high at the same time! Even I saw the same thing. UPDATE 4: Recently, Chrome updated to v24 Stable (I am using stable from a long time now). I was experiencing this problem a lot less in Chrome 23, but this is back in Chrome 24. Seams like Chrome 24 is the most affected from this bug, as this same problem was high in Chrome 24 beta also. UPDATE 5: Chrome was updated to v25 Stable. This problem is 99% Gone, it is still there in 1% of the cases. One such example is when I leave chrome inactive for a while with a few tabs open, the tabs go black and no activity can get them back to active state. If I open a new tab, the new tab is OK but the others are still black, I need to close all those tabs. UPDATE 6: Chrome updated to v27 Stable channel, this problem is nearly gone. This does happen occasionally, but not as frequent as in earlier versions of Chrome. UPDATE 7: I am on Chrome v35.0.1916.114 Stable, Windows 8.1 Pro Update 1. Some of the other problems appears to be back. Chrome is slow and laggy again. Re-draw time is getting worse. Is anybody else experiencing such issues? Does anybody have a solution to any of these?

  Read the article

• Synergy 1.4.2 Linux server, OSX client, Media/Function key mapping issues

  - by at165dB

  I'm using an Apple bluetooth keybord to control my Linux synergy server. SSH tunneling, Mouse, Keyboard, and Copy&Paste all work. Linux sees all the media/app keys that are on top of the F# keys correctly. However if I press any of those keys while controlling my OSX client, nothing happens on the client. Running synergys with -d DEBUG1 I can see the following keycode info: Pressing the "dim monitor" key that also serves as F1 generates: new mask: 0x2000 event: KeyPress code=232, state=0x0010 new mask: 0x2000 If I press "fn" and the same key, I can see it sending what I'm assuming is an F1: event: KeyPress code=67, state=0x0010 onKeyDown id=61374 mask=0x2000 button=0x0043 send key down to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 new mask: 0x2000 event: KeyRelease code=67, state=0x0010 onKeyUp id=61374 mask=0x2000 button=0x0043 send key up to "foo.cisco.com" id=61374, mask=0x2000, button=0x0043 I'm guessing I need to tweak my synergy.conf so that the server sends keys that it currently isn't. I'm also not sure what I need to do to tweak the keys that it is sending, but are not working. Below are all the other keys I'm having issues with. Does anyone have any idea how I can enable their functionality? brighten monitor: new mask: 0x2000 event: KeyPress code=233, state=0x0010 new mask: 0x2000 expose: new mask: 0x2000 event: KeyPress code=128, state=0x0010 new mask: 0x2000 dashboard: new mask: 0x2000 event: KeyPress code=212, state=0x0010 new mask: 0x2000 dim keyboard: new mask: 0x2000 event: KeyPress code=237, state=0x0010 new mask: 0x2000 brighten keyboard: new mask: 0x2000 event: KeyPress code=238, state=0x0010 new mask: 0x2000 rewind: event: KeyPress code=173, state=0x0010 onKeyDown id=57521 mask=0x2000 button=0x00ad send key down to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad new mask: 0x2000 event: KeyRelease code=173, state=0x0010 onKeyUp id=57521 mask=0x2000 button=0x00ad send key up to "foo.cisco.com" id=57521, mask=0x2000, button=0x00ad play/pause: event: KeyPress code=172, state=0x0010 onKeyDown id=57523 mask=0x2000 button=0x00ac send key down to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac new mask: 0x2000 event: KeyRelease code=172, state=0x0010 onKeyUp id=57523 mask=0x2000 button=0x00ac send key up to "foo.cisco.com" id=57523, mask=0x2000, button=0x00ac fastforward: event: KeyPress code=171, state=0x0010 onKeyDown id=57520 mask=0x2000 button=0x00ab send key down to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab new mask: 0x2000 event: KeyRelease code=171, state=0x0010 onKeyUp id=57520 mask=0x2000 button=0x00ab send key up to "foo.cisco.com" id=57520, mask=0x2000, button=0x00ab mute: event: KeyPress code=121, state=0x0010 onKeyDown id=57517 mask=0x2000 button=0x0079 send key down to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 new mask: 0x2000 event: KeyRelease code=121, state=0x0010 onKeyUp id=57517 mask=0x2000 button=0x0079 send key up to "foo.cisco.com" id=57517, mask=0x2000, button=0x0079 volume down: onKeyDown id=57518 mask=0x2000 button=0x007a send key down to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a new mask: 0x2000 event: KeyRelease code=122, state=0x0010 onKeyUp id=57518 mask=0x2000 button=0x007a send key up to "foo.cisco.com" id=57518, mask=0x2000, button=0x007a volume up: event: KeyPress code=123, state=0x0010 onKeyDown id=57519 mask=0x2000 button=0x007b send key down to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b new mask: 0x2000 event: KeyRelease code=123, state=0x0010 onKeyUp id=57519 mask=0x2000 button=0x007b send key up to "foo.cisco.com" id=57519, mask=0x2000, button=0x007b eject: event: KeyPress code=169, state=0x0010 onKeyDown id=57345 mask=0x2000 button=0x00a9 send key down to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9 new mask: 0x2000 event: KeyRelease code=169, state=0x0010 onKeyUp id=57345 mask=0x2000 button=0x00a9 send key up to "foo.cisco.com" id=57345, mask=0x2000, button=0x00a9

  Read the article

• Debian Lenny to Debian Squeeze upgrade problems

  - by Roland Soós

  Hi! Yesterday I made a dist-upgrade on my Debian Lenny server. I thought it will be easy as an usual upgrade, but it's not. I got a lot of problem after the update: # apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: linux-image-2.6-amd64 : Depends: linux-image-2.6.32-5-amd64 but it is not installed E: Unmet dependencies. Try using -f. Then I tried the suggestion: # apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libio-compress-base-perl libatk1.0-0 libts-0.0-0 libmime-types-perl libc-client2007b libgtk2.0-common libxfixes3 libgsf-1-common hicolor-icon-theme libfile-remove-perl libxcomposite1 libltdl3-dev libneon27 libmd5-perl libwmf0.2-7 libilmbase6 libatk1.0-data djvulibre-desktop libdirectfb-1.0-0 fam libxinerama1 libcroco3 libopenexr6 libgsf-1-114 libmail-box-perl libdjvulibre21 openssl-blacklist librsvg2-2 libio-compress-zlib-perl libsysfs2 libbeecrypt6 libxdamage1 libobject-realize-later-perl libuser-identity-perl libgtk2.0-bin libxi6 libxcursor1 portmap libxrandr2 libgtk2.0-0 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: linux-image-2.6.32-5-amd64 Suggested packages: linux-doc-2.6.32 The following NEW packages will be installed: linux-image-2.6.32-5-amd64 0 upgraded, 1 newly installed, 0 to remove and 121 not upgraded. 98 not fully installed or removed. Need to get 0 B/28.6 MB of archives. After this operation, 103 MB of additional disk space will be used. Do you want to continue [Y/n]? y perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Preconfiguring packages ... (Reading database ... 37915 files and directories currently installed.) Unpacking linux-image-2.6.32-5-amd64 (from .../linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb) ... locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r dpkg: error processing /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb (--unpack): failed in write on buffer copy for backend dpkg-deb during `./lib/modules/2.6.32-5-amd64/kernel/sound/pci/hda/snd-hda-codec-realtek.ko': No space left on device configured to not write apport reports dpkg-deb: subprocess paste killed by signal (Broken pipe) locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r Running postrm hook script /sbin/update-grub. Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.26-2-amd64 Updating /boot/grub/menu.lst ... done Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 2.6.32-5-amd64 /boot/vmlinuz-2.6.32-5-amd64 Errors were encountered while processing: /var/cache/apt/archives/linux-image-2.6.32-5-amd64_2.6.32-30_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) # dpkg-reconfigure locales perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "hu_HU.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: Nincs ilyen f?jl vagy k?nyvt?r /usr/sbin/dpkg-reconfigure: locales is broken or not fully installed Then I stucked. Do you have any idea how could I solve this?

  Read the article

• How can I tell Firefox to ignore unprintable characters?

  - by BrianH

  Edit: Summary Apparently the intended character to display in this case is an "en-dash". This page has a table half way down that shows that for the &ndash;, some software will convert the correct hex code of 2013 to 0096. (look at the first row in the table). This answer on Stackoverflow explains that somehow this is a mixup between Windows-1252 and UTF-8 This blog article enforces this: Character 150 (0x96) is the unicode character "START OF GUARDED AREA" in the non-displayed C1 control character range, but in the Windows-1252 encoding it's mapped to to the displayable character 0x2013 "en-dash" (a short dash). Others have struggled with this when producing content, as this answer on Stackoverflow shows how to replace 0x0096 with 0x2013. Google must realize this, because as stated in my original question below, Google's cached version of the Amazon page has &ndash; so it seems they are automatically correcting these mistakes on pages they cache. I have tried setting my encoding to Windows-1252 but that does not help. So now I guess my question is, how can I tell Firefox to ignore unprintable characters like these? Original content below: (Firefox 3.6.13 on Windows XP) Every once in a while I notice an odd character on certain web pages when browsing the web. It is a outline of a box with a 4-digit number inside. And example of a page that has these characters is: http://aws.amazon.com/ec2/#highlights After each section heading (Elastic, Completely Controlled, ...) I see a box with the number "0096" inside. I looked at the cached version on Google, and google has &ndash; in it's place, so I'm guessing I should be seeing a dash there instead of the box with the numbers in it. I have tried changing the character encoding in Firefox but haven't been able to find one that shows these characters correctly. Is there a way to allow Firefox to view these characters? Thanks in advance! Edit - adding a screen shot of the "special" characters: Edit #2 - tried in Ubuntu - new screenshots I logged into my Ubuntu desktop and browsed to the amazon page in Chrome and Firefox. Chrome completely ignores character, even if I inspect or view page source. Firefox in Unbutu displays the character exactly like Firefox on my Windows XP box. I copied the character and played around with it at the command line - here is a screenshot of the results: It looks like I can paste the character into this post as well: `` It is definitely not isolated to Windows XP. I tried setting the character encoding for my terminal to Windows 1252 (from Dennis' comment below), but then it just displays this character as a question mark. I pulled the webpage down with wget and with curl, and both outputs show this characters as: <96> It makes me wonder if this character renders correctly for anyone? It appears webkit just ignores it, my IE6 ignores it, Firefox displays the box with the numbers in it. I would have to imagine the design team at Amazon can see it correctly? It's not a huge deal to get these characters displaying correctly, but it would be nice to know if there is a solution to this.

  Read the article

• segfault when cd-ing into certain directories in bash

  - by user84207

  I have noticed this very strange behavior recently. After cd into certain directories, I get a segfault on the terminal. --- SIGSEGV (Segmentation fault) @ 0 (0) --- --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV (core dumped) +++ segmentation fault (core dumped) I proceeded to strace a bash session in which I cd into the target directory, and was able to reproduce the problem. I attached the log to this pastebin: I paste below the few lines from the read of "cd stumpwm", which is the directory in question, until the segfault. I included a few of the repetitions of calls to "rt_sigprocmask" and "brk" to give a glimpse of the pattern, which occurs for most of the strace, read(0, cd stumpwm "c", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "d", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, " ", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "s", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "t", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "u", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "m", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "p", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "w", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "m", 1) = 1 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 read(0, "\n", 1) = 1 rt_sigprocmask(SIG_BLOCK, [INT], [], 8) = 0 ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig -icanon -echo ...}) = 0 ioctl(0, SNDCTL_TMR_STOP or TCSETSW, {B38400 opost isig icanon -echo ...}) = 0 ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B38400 opost isig icanon -echo ...}) = 0 rt_sigprocmask(SIG_SETMASK, [], NULL, 8) = 0 rt_sigaction(SIGINT, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, {0x49edc0, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTERM, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGQUIT, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGALRM, {0x457f50, [HUP INT ILL TRAP ABRT BUS FPE USR1 SEGV USR2 PIPE ALRM TERM XCPU XFSZ VTALRM SYS], SA_RESTORER, 0x7ffff76254a0}, {0x49edc0, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTSTP, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTTOU, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGTTIN, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, {SIG_IGN, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGWINCH, {0x457920, [], SA_RESTORER, 0x7ffff76254a0}, {0x49e6e0, [], SA_RESTORER|SA_RESTART, 0x7ffff76254a0}, 8) = 0 rt_sigaction(SIGINT, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, {0x457d50, [], SA_RESTORER, 0x7ffff76254a0}, 8) = 0 brk(0xa9a000) = 0xa9a000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9b000) = 0xa9b000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9c000) = 0xa9c000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9d000) = 0xa9d000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9e000) = 0xa9e000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xa9f000) = 0xa9f000 brk(0xaa0000) = 0xaa0000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0xaa1000) = 0xaa1000 brk(0xaa2000) = 0xaa2000 (pattern of rt_sigprocmask, brk continues ...) rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0x1d5b000) = 0x1d5b000 brk(0x1d5c000) = 0x1d5c000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 brk(0x1d5d000) = 0x1d5d000 brk(0x1d5e000) = 0x1d5e000 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 rt_sigprocmask(SIG_BLOCK, NULL, [], 8) = 0 --- SIGSEGV (Segmentation fault) @ 0 (0) --- --- SIGSEGV (Segmentation fault) @ 0 (0) --- +++ killed by SIGSEGV (core dumped) +++ segmentation fault (core dumped) How can I debug this? Is this likely to be a bash problem? The error does not occur with another shell, such as eshell. I have also run an fschk, although I haven't been able to see the output because of this bug.

  Read the article

• Have to dhclient each restart to access internet

  - by Zeophlite

  So each time I restart my ubuntu server (virtual 10.04, via Xencenter), I have to call dhclient before I can access the internet: http://img813.imageshack.us/i/dhclient.png/ What do I need to change to get internet access automatically? Apologies for posting images, I'm using Xencenter, so I can't copy/paste the console output EDIT:: daniel@workwork:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.69.136 netmask 255.255.255.0 network 192.168.69.0 broadcast 192.168.69.255 gateway 192.168.69.1 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.69.120 dns-search workwork.com.au daniel@workwork:~$ ifconfig eth0 Link encap:Ethernet HWaddr ae:11:14:22:0a:03 inet6 addr: fe80::ac11:14ff:fe22:a03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:85 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10496 (10.4 KB) TX bytes:13086 (13.0 KB) Interrupt:32 Base address:0x6000 eth1 Link encap:Ethernet HWaddr b2:2c:40:f2:a0:fa inet addr:192.168.69.167 Bcast:192.168.69.255 Mask:255.255.255.0 inet6 addr: fe80::b02c:40ff:fef2:a0fa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13448 errors:0 dropped:0 overruns:0 frame:0 TX packets:3100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7679428 (7.6 MB) TX bytes:282286 (282.2 KB) Interrupt:36 Base address:0xa100 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:179 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:36905 (36.9 KB) TX bytes:36905 (36.9 KB) daniel@workwork:/var/lib/dhcp3$ cat dhclient.leases lease { interface "eth1"; fixed-address 192.168.69.167; filename "boot\\x86\\wdsnbp.com"; option subnet-mask 255.255.255.0; option routers 192.168.69.1; option dhcp-lease-time 28800; option dhcp-message-type 5; option domain-name-servers 192.168.69.120,192.168.69.121; option dhcp-server-identifier 192.168.69.120; option dhcp-renewal-time 14400; option dhcp-rebinding-time 25200; option domain-name "workwork.com.au"; renew 5 2011/03/18 07:36:53; rebind 5 2011/03/18 11:35:39; expire 5 2011/03/18 12:35:39; } lease { interface "eth1"; fixed-address 192.168.69.167; filename "boot\\x86\\wdsnbp.com"; option subnet-mask 255.255.255.0; option routers 192.168.69.1; option dhcp-lease-time 28800; option dhcp-message-type 5; option domain-name-servers 192.168.69.120,192.168.69.121; option dhcp-server-identifier 192.168.69.120; option dhcp-renewal-time 14400; option dhcp-rebinding-time 25200; option domain-name "workwork.com.au"; renew 5 2011/03/18 08:51:58; rebind 5 2011/03/18 12:24:16; expire 5 2011/03/18 13:24:16; } daniel@workwork:/var/lib/dhcp3$ cat dhclient.eth0.leases daniel@workwork:/var/lib/dhcp3$ ifconfig eth1 before and after dhclient http://img692.imageshack.us/i/prepost.png/

  Read the article

• Drupal & nginx : a sound "general purpose" configuration?

  - by sbrattla

  After a bit back and forth with configuring Drupal and nginx to work together, I've come up with the below configuration for a site. It works well, both with private and public file systems. However, as I am fairly new to nginx I'd like to hear if there is something with this configuration that I should change (for Please note! I'm aiming towards getting feedback on a general purpose Drupal configuration. That is, a configuration which others who are trying out Drupal + nginx can "copy paste" to get up and running. server { listen 80; server_name www.example.* example.*; access_log /home/example/www/logs/access.log; error_log /home/example/www/logs/error.log; root /home/example/www/public_html; # Site Icon location = /favicon.ico { log_not_found off; access_log off; } # Search Engines location = /robots.txt { allow all; log_not_found off; access_log off; } # Drush location = /backup { deny all; } # Very rarely should these ever be accessed from outside # the local network. location ~* \.(txt|log)$ { allow 10.0.0.0/8; allow 172.16.0.0/12; allow 192.168.0.0/16; deny all; } location ~ \..*/.*\.php$ { return 403; } # Default location location / { try_files $uri @rewrite; } # Files managed by Drupal will be served via PHP. location ~* /system/files/ { access_log off; try_files $uri @rewrite; } ## Images and static content is treated different location ~* \.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; } # Some Drupal modules enforce no slash (/) at the end # of the URL. location @rewrite { rewrite_log on; rewrite ^/(.*)$ /index.php?q=$1; } # PHP5-FPM is used to handle PHP. location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_pass unix:/var/run/example.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 180; fastcgi_read_timeout 180; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } }

  Read the article

• PHP, Apache and curl: Differences between Windows and Linux?

  - by beginner_

  I'm trying to run my php App on Ubuntu Server 11.10. This App works fine under Apache + PHP in windows. I have other applications that I can simply copy&paste between the 2 OS and they work on both. (These don't use cURL). However this one uses the php library tonic (RESTful webservices) and makes us of php cURL module. The issue is I'm not getting an error message which makes it impossible to find the issue. I (must) use NTLM authentication and this is done with AuthenNTLM Apache Module: Order allow,deny Allow from all PerlAuthenHandler Apache2::AuthenNTLM AuthType ntlm AuthName "Protected Access" require valid-user PerlAddVar ntdomain "domainName server" PerlSetVar defaultdomain domainName PerlSetVar ntlmsemtimeout 2 PerlSetVar ntlmdebug 1 PerlSetVar splitdomainprefix 0 All files that cURL needs to fetch override AuthenNTLM authentication: order deny,allow deny from all allow from 127.0.0.1 Satisfy any Since these files are only fectehd by cURL from same server, access can be limited to localhost. Possible issues are: NTLM auth isn't overridden for files requested through cURL (even though AllowOverride All is set) curl works differently on linux $ch = curl_init(); curl_setopt($ch, CURLOPT_COOKIE, $strCookie); curl_setopt($ch, CURLOPT_URL, $baseUrl . $queryString); curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1); $html = curl_exec($ch); curl_close($ch); other? Apache log says: [error] Bad/Missing NTLM/Basic Authorization Header for /myApp/webservice/local/viewList.php But this directory should override NTLM authentication using curl command line from windows to access same resource i get: <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html> <head> <title>406 Not Acceptable</title> </head> <body> <h1>Not Acceptable</h1> <p>An appropriate representation of the requested resource /myApp/webservice/myResource could not be found on this server.</p> Available variants: <ul> <li><a href="myResource.php">myResource.php</a> , type application/x-httpd-php</li> </ul> <hr> <address>Apache/2.2.20 (Ubuntu) Server at localhost Port 80</address> </body> </html> Note: This is duplicate from http://stackoverflow.com/questions/9821979/php-curl-on-linux-what-is-the-difference-to-curl-on-windows Is it was suggested I post it here. EDIT: Please see Ubuntu Server: Apache2 seems to attach .php to URI as I discovered why it does not work but need help so the issue does not occur anymore. ANSWER: The issue is the default Apache configuration on Ubuntu: Options Indexes FollowSymLinks MultiViews MultiViews is changing request_uri from myResource to myResource.php. Solutions: disable MultiViews in .htaccess: Options -MultiViews remove MultiViews from default config rename the file as example to myResourceClass I chose last option because that should work regardless of configuration and I only have 3 such files so the change took about 30 secs...

  Read the article

• How To Start Your Own Professional Blog with WordPress

  - by Matthew Guay

  Would you like to start your own blog or website?  With a free WordPress  account, it’s free and easy to get started creating your own professional quality blog site. This is the first part in a series on how to create your own professional quality blog site. No, we’re not talking about some cheapo looking blog from Blogger or something on Facebook, but creating a quality blog you can be proud of and present to millions of readers online. WordPress is one of the most popular blogging platforms, powering hundreds of high-profile websites and blogs around the world.  It’s both powerful and easy to use, which makes it great whether you’re just starting out or are a blogging pro.  To start out with your blogging project WordPress is completely free, and you can use the online interface or install the WordPress software on your own server and blog from there. Getting Started You can start a blog in just a few minutes.  Head over to WordPress.com and click Sign up now on the right-hand side of the main page. Enter a username and password, check that you agree with the legal terms, select the “Gimme a blog” bullet, and click Next. WordPress may inform you that your username is already taken, simply choose a new one and try again. Next, choose a domain for your blog.  This will be the address for your site, and cannot be changed, so be sure to choose exactly what you want.  If you’d prefer your address to be yourname.com instead of yourname.wordpress.com, you can add your own domain for a fee after your blog is setup…but we’ll cover that later. Once you click signup, you will be sent a confirmation email.  While you wait for the email to arrive you can go ahead and enter in your name and a short bio about yourself. When you receive your confirmation email, click the link.  Congratulations; you now have your own blog! You can view your new blog immediately, though the default theme isn’t very interesting without your content and pictures. Back on the page you opened from the email, click Login to access your blog’s administration page and to start adding stuff to your blog.  You can also access your blog’s admin page anytime by from yourname.wordpress.com/admin, substituting your own blog name for yourname. Enter your username and password, then click Log in to get started. Adding Content to your WordPress.com Blog When you sign in to your WordPress blog, you’ll first see the WordPress Admin page.  Here you can see recent posts and comments, and you can see stats of how many people have visited your site.  You can also access all of your blog tools and settings right from this page. To add a new post to your blog, click the Posts link on the left, then click “Add New” either on the left menu or on the top of the Edit Posts page.  Or, if you want to edit the default first post, hover over it and select Edit. Or click the New Posts button on the top of the page.  This menu bar is always visible whenever you’re logged in, so it’s an easy way to add a post. The editor lets you easily write anything you want in a Microsoft Word-style editor.  You can format your text, add lists, links, quotes, and more.  When you’re ready to share your content with the world, click Publish on the right side. To add pictures or other files, click the picture icon beside “Upload/Insert”.  Your free blog account can store up to 3Gb of pictures and documents which will definitely give you a good start. Click Select Files, and then choose the pictures or documents you want to add to your post. When the pictures have uploaded, you can add a caption and choose how to position the picture.  When you’re finished, select “Insert into Post”.   Or, if you want to add a video, click the video button.  You have to add a paid upgrade to upload videos directly, but you can add YouTube and other online videos for free. Click the “From URL” tab, and then paste the link to the YouTube video and click Insert into post. If you’re a code geek, click the HTML tab in the editor and edit the HTML of your blog post the geeky way. Once you’ve added all your content and edited it the way you want, click the Publish button on the right of the editor.  Or, you can click Preview to make sure it looks right, and then click Publish. Here’s our blog with the new blog post containing a picture and video.  While you’re getting to know you’re way around the controls in WordPress, the Preview feature will be your best friend while you try to organize the content to your liking.   Conclusion It only takes a couple minutes to get started blogging at WordPress.com. Whether you want to write about your daily life, share pictures of your children, or review the latest books and gadgets, WordPress.com is a great place to get started for free.  But we’ve only covered a small portion of the WordPress features…but this should get you started. Check back for more WordPress and blogging coverage coming up soon! Links Signup for a free WordPress.com account Similar Articles Productive Geek Tips Add Social Bookmarking (Digg This!) Links to your Wordpress BlogHow-To Geek SoftwareProtecting Your WordPress Admin Panel From Hackers With .htaccessMake a Backup Copy of your Production Wordpress Blog on UbuntuLinux QuickTip: Downloading and Un-tarring in One Step TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

  Read the article

• OCR anything with OneNote 2007 and 2010

  - by Matthew Guay

  Quality OCR software can often be very expensive, but you may have one already installed on your computer that you didn’t know about.  Here’s how you can use OneNote to OCR anything on your computer. OneNote is one of the overlooked gems in recent versions of Microsoft Office.  OneNote makes it simple to take notes and keep track of everything with integrated search, and offers more features than its popular competitor Evernote.  One way it is better is its high quality optical character recognition (OCR) engine.  One of Evernote’s most popular features is that you can search for anything, including text in an image, and you can easily find it.  OneNote takes this further, and instantly OCRs any text in images you add.  Then, you can use this text easily and copy it from the image.  Let’s see how this works and how you can use OneNote as the ultimate OCR. Please Note: This feature is available in OneNote 2007 and 2010.  OneNote 2007 is included with Office 2007 Home and Student, Enterprise, and Ultimate, while OneNote 2010 is included with all edition of Office 2010 except for Starter edition. OCR anything First, let’s add something to OCR into OneNote.  There are many different ways you can add items to OCR into OneNote.  Open a blank page or one you want to insert something into, and then follow these steps to add what you want into OneNote. Picture Simply drag-and-drop a picture with text into a notebook… You can insert a picture directly from OneNote as well.  In OneNote 2010, select the Insert tab, and then choose Picture. In OneNote 2007, select the Insert menu, select Picture, and then choose From File.   Screen Clipping There are many times we’d like to copy text from something we see onscreen, but there is no direct way to copy text from that thing.  For instance, you cannot copy text from the title-bar of a window, or from a flash-based online presentation.  For these cases, the Screen Clipping option is very useful.  To add a clip of anything onscreen in OneNote 2010, select the Insert tab in the ribbon and click Screen Clipping. In OneNote 2007, either click the Clip button on the toolbar or select the Insert menu and choose Screen Clipping.   Alternately, you can take a screen clipping by pressing the windows key + S. When you click Screen Clipping, OneNote will minimize, your desktop will fade lighter, and your mouse pointer will change to a plus sign.  Now, click and drag over anything you want to add to OneNote.  Here we’re selecting the title of this article. The section you selected will now show up in your OneNote notebook, complete with the date and time the clip was made. Insert a file You’re not limited to pictures; OneNote can even OCR anything in most files on your computer.  You can add files directly in OneNote 2010 by selecting File Printout in the Insert tab. In OneNote 2007, select the Insert menu and choose Files as Printout. Choose the file you want to add to OneNote in the dialog. Select Insert, and OneNote will pause momentarily as it processes the file. Now your file will show up in OneNote as a printout with a link to the original file above it. You can also send any file directly to OneNote via the OneNote virtual printer.  If you have a file open, such as a PDF, that you’d like to OCR, simply open the print dialog in that program and select the “Send to OneNote” printer. Or, if you have a scanner, you can scan documents directly into OneNote by clicking Scanner Printout in the Insert tab in OneNote 2010. In OneNote 2003, to add a scanned document select the Insert menu, select Picture, and then choose From Scanner or Camera. OCR the image, file, or screenshot you put in OneNote Now that you’ve got your stuff into OneNote, let’s put it to work.  OneNote automatically did an OCR scan on anything you inserted into OneNote.  You can check to make sure by right-clicking on any picture, screenshot, or file you inserted.  Select “Make Text in Image Searchable” and then make sure the correct language is selected. Now, you can copy text from the Picture.  Simply right-click on the picture, and select “Copy Text from Picture”. And here’s the text that OneNote found in this picture: OCR anything with OneNote 2007 and 2010 - Windows Live Writer Not bad, huh?  Now you can paste the text from the picture into a document or anywhere you need to use the text. If you are instead copying text from a printout, it may give you the option to copy text from this page or all pages of the printout.   This works the exact same in OneNote 2007. In OneNote 2010, you can also edit the text OneNote has saved in the image from the OCR.  This way, if OneNote read something incorrectly you can change it so you can still find it when you use search in OneNote.  Additionally, you can copy only a specific portion of the text from the edit box, so it can be useful just for general copying as well.  To do this, right-click on the item and select “Edit Alt Text”. Here is the window to edit alternate text.  If you want to copy only a portion of the text, simply select it and press Ctrl+C to copy that portion. Searching OneNote’s OCR engine is very useful for finding specific pictures you have saved in OneNote.  Simply enter your search query in the search box on top right, and OneNote will automatically find all instances of that term in all of your notebooks.  Notice how it highlights the search term even in the image! This works the same in OneNote 2007.  Notice how it highlighted “How-to” in a shot of the header image in our favorite website. In Windows Vista and 7, you can even search for things OneNote OCRed from the Start Menu search.  Here the start menu search found the words “Windows Live Writer” in our OCR Test notebook in OneNote where we inserted the screen clip above. Conclusion OneNote is a very useful OCR tool, and can help you capture text from just about anything.  Plus, since you can easily search everything you have stored in OneNote, you can quickly find anything you insert anytime.  OneNote is one of the least-used Office tools, but we have found it very useful and hope you do too. Similar Articles Productive Geek Tips Add or Remove Apps from the Microsoft Office 2007 or 2010 SuiteRemove Office 2010 Beta and Reinstall Office 2007How To Create and Publish Blog Posts in Word 2010 & 2007How To Copy Worksheets in Excel 2007 & 2010Add Page Numbers to Documents in Word 2007 & 2010 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Using TrueCrypt to Secure Your Data Quickly Schedule Meetings With NeedtoMeet Share Flickr Photos On Facebook Automatically Are You Blocked On Gtalk? Find out Discover Latest Android Apps On AppBrain The Ultimate Guide For YouTube Lovers

  Read the article

• Scan a Windows PC for Viruses from a Ubuntu Live CD

  - by Trevor Bekolay

  Getting a virus is bad. Getting a virus that causes your computer to crash when you reboot is even worse. We’ll show you how to clean viruses from your computer even if you can’t boot into Windows by using a virus scanner in a Ubuntu Live CD. There are a number of virus scanners available for Ubuntu, but we’ve found that avast! is the best choice, with great detection rates and usability. Unfortunately, avast! does not have a proper 64-bit version, and forcing the install does not work properly. If you want to use avast! to scan for viruses, then ensure that you have a 32-bit Ubuntu Live CD. If you currently have a 64-bit Ubuntu Live CD on a bootable flash drive, it does not take long to wipe your flash drive and go through our guide again and select normal (32-bit) Ubuntu 9.10 instead of the x64 edition. For the purposes of fixing your Windows installation, the 64-bit Live CD will not provide any benefits. Once Ubuntu 9.10 boots up, open up Firefox by clicking on its icon in the top panel. Navigate to http://www.avast.com/linux-home-edition. Click on the Download tab, and then click on the link to download the DEB package. Save it to the default location. While avast! is downloading, click on the link to the registration form on the download page. Fill in the registration form if you do not already have a trial license for avast!. By the time you’ve filled out the registration form, avast! will hopefully be finished downloading. Open a terminal window by clicking on Applications in the top-left corner of the screen, then expanding the Accessories menu and clicking on Terminal. In the terminal window, type in the following commands, pressing enter after each line. cd Downloadssudo dpkg –i avast* This will install avast! on the live Ubuntu environment. To ensure that you can use the latest virus database, while still in the terminal window, type in the following command: sudo sysctl –w kernel.shmmax=128000000 Now we’re ready to open avast!. Click on Applications on the top-left corner of the screen, expand the Accessories folder, and click on the new avast! Antivirus item. You will first be greeted with a window that asks for your license key. Hopefully you’ve received it in your email by now; open the email that avast! sends you, copy the license key, and paste it in the Registration window. avast! Antivirus will open. You’ll notice that the virus database is outdated. Click on the Update database button and avast! will start downloading the latest virus database. To scan your Windows hard drive, you will need to “mount” it. While the virus database is downloading, click on Places on the top-left of your screen, and click on your Windows hard drive, if you can tell which one it is by its size. If you can’t tell which is the correct hard drive, then click on Computer and check out each hard drive until you find the right one. When you find it, make a note of the drive’s label, which appears in the menu bar of the file browser. Also note that your hard drive will now appear on your desktop. By now, your virus database should be updated. At the time this article was written, the most recent version was 100404-0. In the main avast! window, click on the radio button next to Selected folders and then click on the “+” button to the right of the list box. It will open up a dialog box to browse to a location. To find your Windows hard drive, click on the “>” next to the computer icon. In the expanded list, find the folder labelled “media” and click on the “>” next to it to expand it. In this list, you should be able to find the label that corresponds to your Windows hard drive. If you want to scan a certain folder, then you can go further into this hierarchy and select that folder. However, we will scan the entire hard drive, so we’ll just press OK. Click on Start scan and avast! will start scanning your hard drive. If a virus is found, you’ll be prompted to select an action. If you know that the file is a virus, then you can Delete it, but there is the possibility of false positives, so you can also choose Move to chest to quarantine it. When avast! is done scanning, it will summarize what it found on your hard drive. You can take different actions on those files at this time by right-clicking on them and selecting the appropriate action. When you’re done, click Close. Your Windows PC is now free of viruses, in the eyes of avast!. Reboot your computer and with any luck it will now boot up! Alternatives to avast! If avast! and a liberal amount of Googling doesn’t fix your problem, it’s possible that a different virus scanner will fix your obscure issue. Here are a list of other virus scanners available for Ubuntu that are either free or offer free trials. See their support forums for help on installing these virus scanners. Avira AntiVir Personal for Linux / Solaris Panda Antivirus for Linux Installation and usage guide from Ubuntu F-PROT Antivirus for Linux ClamAV installation and usage guide from Ubuntu NOD32 Antivirus for Linux Kaspersky Anti-Virus 2010 Bitdefender Antivirus for Unices Conclusion Running avast! from a Ubuntu Live CD can clean the vast majority of viruses from your Windows PC. This is another reason to always have a Ubuntu Live CD ready just in case something happens to your Windows installation! Similar Articles Productive Geek Tips Secure Computing: Windows Live OneCareHow To Remove Antivirus Live and Other Rogue/Fake Antivirus MalwareUse the Windows Key for the "Start" Menu in Ubuntu LinuxScan Files for Viruses Before You Download With Dr.WebAsk the Readers: Share Your Tips for Defeating Viruses and Malware TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 The Ultimate Guide For YouTube Lovers Will it Blend? iPad Edition Penolo Lets You Share Sketches On Twitter Visit Woolyss.com for Old School Games, Music and Videos Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC

  Read the article

• How To Activate Your Free Office 2007 to 2010 Tech Guarantee Upgrade

  - by Matthew Guay

  Have you purchased Office 2007 since March 5th, 2010?  If so, here’s how you can activate and download your free upgrade to Office 2010! Microsoft Office 2010 has just been released, and today you can purchase upgrades from most retail stores or directly from Microsoft via download.  But if you’ve purchased a new copy of Office 2007 or a new computer that came with Office 2007 since March 5th, 2010, then you’re entitled to an absolutely free upgrade to Office 2010.  You’ll need enter information about your Office 2007 and then download the upgrade, so we’ll step you through the process. Getting Started First, if you’ve recently purchased Office 2007 but haven’t installed it, you’ll need to go ahead and install it before you can get your free Office 2010 upgrade.  Install it as normal.   Once Office 2007 is installed, run any of the Office programs.  You’ll be prompted to activate Office.  Make sure you’re connected to the internet, and then click Next to activate. Get your Free Upgrade to Office 2010 Now you’re ready to download your upgrade to Office 2010.  Head to the Office Tech Guarantee site (link below), and click Upgrade now. You’ll need to enter some information about your Office 2007.  Check that you purchased your copy of Office 2007 after March 5th, select your computer manufacturer, and check that you agree to the terms. Now you’re going to need the Product ID number from Office 2007.  To find this, open Word or any other Office 2007 application.  Click the Office Orb, and select Options on the bottom. Select the Resources button on the left, and then click About. Near the bottom of this dialog, you’ll see your Product ID.  This should be a number like: 12345-123-1234567-12345   Go back to the Office Tech Guarantee signup page in your browser, and enter this Product ID.  Select the language of your edition of Office 2007, enter the verification code, and then click Submit. It may take a few moments to validate your Product ID. When it is finished, you’ll be taken to an order page that shows the edition of Office 2010 you’re eligible to receive.  The upgrade download is free, but if you’d like to purchase a backup DVD of Office 2010, you can add it to your order for $13.99.  Otherwise, simply click Continue to accept. Do note that the edition of Office 2010 you receive may be different that the edition of Office 2007 you purchased, as the number of editions has been streamlined in the Office 2010 release.  Here’s a chart you can check to see what edition you’ll receive.  Note that you’ll still be allowed to install Office on the same number of computers; for example, Office 2007 Home and Student allows you to install it on up to 3 computers in the same house, and your Office 2010 upgrade will allow the same. Office 2007 Edition Office 2010 Upgrade You’ll Receive Office 2007 Home and Student Office Home and Student 2010 Office Basic 2007Office Standard 2007 Office Home and Business 2010 Office Small Business 2007Office Professional 2007Office Ultimate 2007 Office Professional 2010 Office Professional 2007 AcademicOffice Ultimate 2007 Academic Office Professional Academic 2010 Sign in with your Windows Live ID, or create a new one if you don’t already have one. Enter your name, select your country, and click Create My Account.  Note that Office will send Office 2010 tips to your email address; if you don’t wish to receive them, you can unsubscribe from the emails later.   Finally, you’re ready to download Office 2010!  Click the Download Now link to start downloading Office 2010.  Your Product Key will appear directly above the Download link, so you can copy it and then paste it in the installer when your download is finished.  You will additionally receive an email with the download links and product key, so if your download fails you can always restart it from that link. If your edition of Office 2007 included the Office Business Contact Manager, you will be able to download it from the second Download link.  And, of course, even if you didn’t order a backup DVD, you can always burn the installers to a DVD for a backup.   Install Office 2010 Once you’re finished downloading Office 2010, run the installer to get it installed on your computer.  Enter your Product Key from the Tech Guarantee website as above, and click Continue. Accept the license agreement, and then click Upgrade to upgrade to the latest version of Office.   The installer will remove all of your Office 2007 applications, and then install their 2010 counterparts.  If you wish to keep some of your Office 2007 applications instead, click Customize and then select to either keep all previous versions or simply keep specific applications. By default, Office 2010 will try to activate online automatically.  If it doesn’t activate during the install, you’ll need to activate it when you first run any of the Office 2010 apps.   Conclusion The Tech Guarantee makes it easy to get the latest version of Office if you recently purchased Office 2007.  The Tech Guarantee program is open through the end of September, so make sure to grab your upgrade during this time.  Actually, if you find a great deal on Office 2007 from a major retailer between now and then, you could also take advantage of this program to get Office 2010 cheaper. And if you need help getting started with Office 2010, check out our articles that can help you get situated in your new version of Office! Link Activate and Download Your free Office 2010 Tech Guarantee Upgrade Similar Articles Productive Geek Tips Remove Office 2010 Beta and Reinstall Office 2007Upgrade Office 2003 to 2010 on XP or Run them Side by SideCenter Pictures and Other Objects in Office 2007 & 2010Change the Default Color Scheme in Office 2010Show Two Time Zones in Your Outlook 2007 Calendar TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer XPS file format & XPS Viewer Explained Microsoft Office Web Apps Guide

  Read the article

• Android - creating a custom preferences activity screen

  - by Bill Osuch

  Android applications can maintain their own internal preferences (and allow them to be modified by users) with very little coding. In fact, you don't even need to write an code to explicitly save these preferences, it's all handled automatically! Create a new Android project, with an intial activity title Main. Create two more activities: ShowPrefs, which extends Activity Set Prefs, which extends PreferenceActivity Add these two to your AndroidManifest.xml file: <activity android:name=".SetPrefs"></activity> <activity android:name=".ShowPrefs"></activity> Now we'll work on fleshing out each activity. First, open up the main.xml layout file and add a couple of buttons to it: <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android"    android:orientation="vertical"    android:layout_width="fill_parent"    android:layout_height="fill_parent"> <Button android:text="Edit Preferences"    android:id="@+id/prefButton"    android:layout_width="wrap_content"    android:layout_height="wrap_content"    android:layout_gravity="center_horizontal"/> <Button android:text="Show Preferences"    android:id="@+id/showButton"    android:layout_width="wrap_content"    android:layout_height="wrap_content"    android:layout_gravity="center_horizontal"/> </LinearLayout> Next, create a couple button listeners in Main.java to handle the clicks and start the other activities: Button editPrefs = (Button) findViewById(R.id.prefButton);       editPrefs.setOnClickListener(new View.OnClickListener() {              public void onClick(View view) {                  Intent myIntent = new Intent(view.getContext(), SetPrefs.class);                  startActivityForResult(myIntent, 0);              }      });           Button showPrefs = (Button) findViewById(R.id.showButton);      showPrefs.setOnClickListener(new View.OnClickListener() {              public void onClick(View view) {                  Intent myIntent = new Intent(view.getContext(), ShowPrefs.class);                  startActivityForResult(myIntent, 0);              }      }); Now, we'll create the actual preferences layout. You'll need to create a file called preferences.xml inside res/xml, and you'll likely have to create the xml directory as well. Add the following xml: <?xml version="1.0" encoding="utf-8"?> <PreferenceScreen xmlns:android="http://schemas.android.com/apk/res/android"> </PreferenceScreen> First we'll add a category, which is just a way to group similar preferences... sort of a horizontal bar. Add this inside the PreferenceScreen tags: <PreferenceCategory android:title="First Category"> </PreferenceCategory> Now add a Checkbox and an Edittext box (inside the PreferenceCategory tags): <CheckBoxPreference    android:key="checkboxPref"    android:title="Checkbox Preference"    android:summary="This preference can be true or false"    android:defaultValue="false"/> <EditTextPreference    android:key="editTextPref"    android:title="EditText Preference"    android:summary="This allows you to enter a string"    android:defaultValue="Nothing"/> The key is how you will refer to the preference in code, the title is the large text that will be displayed, and the summary is the smaller text (this will make sense when you see it). Let's say we've got a second group of preferences that apply to a different part of the app. Add a new category just below the first one: <PreferenceCategory android:title="Second Category"> </PreferenceCategory> In there we'll a list with radio buttons, so add: <ListPreference    android:key="listPref"    android:title="List Preference"    android:summary="This preference lets you select an item in a array"    android:entries="@array/listArray"    android:entryValues="@array/listValues" /> When complete, your full xml file should look like this: <?xml version="1.0" encoding="utf-8"?> <PreferenceScreen xmlns:android="http://schemas.android.com/apk/res/android">  <PreferenceCategory android:title="First Category"> <CheckBoxPreference    android:key="checkboxPref"    android:title="Checkbox Preference"    android:summary="This preference can be true or false"    android:defaultValue="false"/> <EditTextPreference    android:key="editTextPref"    android:title="EditText Preference"    android:summary="This allows you to enter a string"    android:defaultValue="Nothing"/>  </PreferenceCategory>  <PreferenceCategory android:title="Second Category">   <ListPreference    android:key="listPref"    android:title="List Preference"    android:summary="This preference lets you select an item in a array"    android:entries="@array/listArray"    android:entryValues="@array/listValues" />  </PreferenceCategory> </PreferenceScreen> However, when you try to save it, you'll get an error because you're missing your array definition. To fix this, add a file called arrays.xml in res/values, and paste in the following: <?xml version="1.0" encoding="utf-8"?> <resources>  <string-array name="listArray">      <item>Value 1</item>      <item>Value 2</item>      <item>Value 3</item>  </string-array>  <string-array name="listValues">      <item>1</item>      <item>2</item>      <item>3</item>  </string-array> </resources> Finally (for the preferences screen at least...) add the code that will display the preferences layout to the SetPrefs.java file:  @Override     public void onCreate(Bundle savedInstanceState) {      super.onCreate(savedInstanceState);      addPreferencesFromResource(R.xml.preferences);      } OK, so now we've got an activity that will set preferences, and save them without the need to write custom save code. Let's throw together an activity to work with the saved preferences. Create a new layout called showpreferences.xml and give it three Textviews: <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android"     android:orientation="vertical"     android:layout_width="fill_parent"     android:layout_height="fill_parent"> <TextView   android:id="@+id/textview1"     android:layout_width="fill_parent"     android:layout_height="wrap_content"     android:text="textview1"/> <TextView   android:id="@+id/textview2"     android:layout_width="fill_parent"     android:layout_height="wrap_content"     android:text="textview2"/> <TextView   android:id="@+id/textview3"     android:layout_width="fill_parent"     android:layout_height="wrap_content"     android:text="textview3"/> </LinearLayout> Open up the ShowPrefs.java file and have it use that layout: setContentView(R.layout.showpreferences); Then add the following code to load the DefaultSharedPreferences and display them: SharedPreferences prefs = PreferenceManager.getDefaultSharedPreferences(this);    TextView text1 = (TextView)findViewById(R.id.textview1); TextView text2 = (TextView)findViewById(R.id.textview2); TextView text3 = (TextView)findViewById(R.id.textview3);    text1.setText(new Boolean(prefs.getBoolean("checkboxPref", false)).toString()); text2.setText(prefs.getString("editTextPref", "<unset>"));; text3.setText(prefs.getString("listPref", "<unset>")); Fire up the application in the emulator and click the Edit Preferences button. Set various things, click the back button, then the Edit Preferences button again. Notice that your choices have been saved.   Now click the Show Preferences button, and you should see the results of what you set:   There are two more preference types that I did not include here: RingtonePreference - shows a radioGroup that lists your ringtones PreferenceScreen - allows you to embed a second preference screen inside the first - it opens up a new set of preferences when clicked

  Read the article

• 17 new features in Visual Studio 2010

  - by vik20000in

  Visual studio 2010 has been released to RTM a few days back. This release of Visual studio 2010 comes with a big number of improvements on many fronts. In this post I will try and point out some of the major improvements in Visual Studio 2010. 1)      Visual studio IDE Improvement. Visual studio IDE has been rewritten in WPF. The look and feel of the studio has been improved for improved readability. Start page has been redesigned and template so that anyone can change the start page as they wish. 2)      Multiple Monitor - Support for Multiple Monitor was already there in Visual studio. But in this edition it has been improved as much that we can now place the document, design and code window outside the IDE in another monitor. 3)      ZOOM in Code Editor – Making the editors in WPF has made significant improvement for them. The best one that I like is the ZOOM feature. We can now zoom in the code editor with the help of the ctrl + Mouse scroll. The zoom feature does not work on the Design surface or windows with icon like solution view and toolbox. 4)      Box Selection - Another Important improvement in the Visual studio 2010 is the box selection. We can select a rectangular by holding down the Alt Key and selecting with mouse.  Now in the rectangular selection we can insert text, Paste same code in different line etc. This is helpful if you want to convert a number of variables from public to private etc… 5)      New Improved Search – One of the best productivity improvements in Visual studio 2010 is its new search as you type support. This has been done in the Navigate To window which can be brought up by pressing (Ctrl + ,). The navigate To windows also take help of the Camel casing and will be able to search with the help of camel casing when character is entered in upper case. For example we can search AOH for AddOrederHeader. 6)      Call Hierarchy – This feature is only available to the Visual C# and Visual C++ editor. The call hierarchy windows displays the calls made to and from (yes both to and from) a selected method property or a constructor. The call hierarchy also shows the implementation of interface and the overrides of virtual or abstract methods. This window is very helpful in understanding the code flow, and evaluating the effect of making changes. The best part is it is available at design time and not at runtime only like a debugger. 7)      Highlighting references – One of the very cool stuff in Visual Studio 2010 is the fact if you select a variable then all the use of that variable will be highlighted alongside. This should work for all the result of symbols returned by Find all reference. This also works for Name of class, objects variable, properties and methods. We can also use the Ctrl + Shift + Down Arrow or Up Arror to move through them. 8)      Generate from usage - The Generate from usage feature lets you use classes and members before you define them. You can generate a stub for any undefined class, constructor, method, property, field, or enum that you want to use but have not yet defined. You can generate new types and members without leaving your current location in code, This minimizes interruption to your workflow.9)      IntelliSense Suggestion Mode - IntelliSense now provides two alternatives for IntelliSense statement completion, completion mode and suggestion mode. Use suggestion mode for situations where classes and members are used before they are defined. In suggestion mode, when you type in the editor and then commit the entry, the text you typed is inserted into the code. When you commit an entry in completion mode, the editor shows the entry that is highlighted on the members list. When an IntelliSense window is open, you can press CTRL+ALT+SPACEBAR to toggle between completion mode and suggestion mode. 10)   Application Lifecycle Management – A client application for management of application lifecycle like version control, work item tracking, build automation, team portal etc is available for free (this is not available for express edition.). 11)   Start Page – The start page has been redesigned with WPF for new functionality and look. Tabbed areas are provided for content from different source including MSDN. Once you open some project the start page closes automatically. The list of recent project also lets you remove project from the list. And above all the start page is customizable enough to be changed as per individual requirement. 12)   Extension Manager – Visual Studio 2010 has provided good ways to be extended. We can also use MEF to extend most of the features of Visual Studio. The new extension manager now can go the visual studio gallery and install the extension without even opening any explorer. 13)   Code snippets – Visual studio 2010 for HTML, Jscript and Asp.net also. 14)   Improved Intelligence for JavaScript has been improved vastly (around 2-5 times). Intelligence now also shows the XML documentation comment on the go. 15)   Web Deployment – Web Deployment has been vastly improved. We can package and publish the web application in one click. Three major supported deployment scenarios are Web packages, one click deployment and Web configuration Transformation. 16)   SharePoint - Visual Studio 2010 also brings vastly improved development experience for SharePoint. We can create, edit, debug, package, deploy and activate SharePoint project from within Visual Studio. Deployment of Site is as easy as hitting F5. 17)   Azure – Visual Studio 2010 also comes with handy improvement for developing on windows Azure environment. Vikram

  Read the article

• How To Skip Commercials in Windows 7 Media Center

  - by DigitalGeekery

  If you use Windows 7 Media Center to record live TV, you’re probably interested in skipping through commercials. After all, a big reason to record programs is to avoid commercials, right? Today we focus on a fairly simple and free way to get you skipping commercials in no time. In Windows 7, the .wtv file format has replaced the dvr-ms file format used in previous versions of Media Center for Recorded TV. The .wtv file format, however, does not work very well with commercial skipping applications.  The Process Our first step will be to convert the recorded .wtv files to the previously used dvr-ms file format. This conversion will be done automatically by WtvWatcher. It’s important to note that this process deletes the original .wtv file after successfully converting to .dvr-ms. Next, we will use DVRMSToolBox with the DTB Addin to handle commercials skipping. This process does not “cut” or remove the commercials from the file. It merely skips the commercials during playback. WtvWatcher Download and install the WTVWatcher (link below). To install WtvWatcher, you’ll need to have Windows Installer 3.1 and .NET Framework 3.5 SP1. If you get the Publisher cannot be verified warning you can go ahead and click Install. We’ve completely tested this app and it contains no malware and runs successfully.   After installing, the WtvWatcher will pop up in the lower right corner of your screen. You will need to set the path to your Recorded TV directory. Click on the button for “Click here to set your recorded TV path…”   The WtvWatcher Preferences window will open…   …and you’ll be prompted to browse for your Recorded TV folder. If you did not change the default location at setup, it will be found at C:\Users\Public\Recorded TV. Click “OK” when finished. Click the “X” to close the Preferences screen. You should now see WtvWatcher begin to convert any existing WTV files.   The process should only take a few minutes per file. Note: If WtvWatcher detects an error during the conversion process, it will not delete the original WTV file.    You will probably want to run WtvWatcher on startup. This will allow WtvWatcher too constantly scan for new .wtv files to convert. There is no setting in the application to run on startup, so you’ll need to copy the WTV icon from your desktop into your Windows start menu “Startup” directory. To do so, click on Start > All Programs, right-click on Startup and click on Open all users. Drag and drop, or cut and paste, the WtvWatcher desktop shortcut into the Startup folder. DVRMSToolBox and DTBAddIn Next, we need to download and install the DVRMSToolBox and the DTBAddIn. These two pieces of software will do the actual commercial skipping. After downloading the DVRMSToolBox zip file, extract it and double-click the setup.exe file.  Click “Next” to begin the installation.   Unless DVRMSToolBox will only be used by Administrator accounts, check the “Modify File Permissions” box. Click “Next.” When you get to the Optional Components window, uncheck Download/Install ShowAnalyzer. We will not be using that application. When the installation is complete, click “Close.”    Next we need to install the DTBAddin. Unzip the download folder and run the appropriate .msi file for your system. It is available in 32 & 64 bit versions. Just double click on the file and take the default options. Click “Finish” when the install is completed. You will then be prompted to restart your computer. After your computer has restarted, open DVRMSToolBox settings by going to Start > All Programs, DVRMSToolBox, and click on DVRMStoMPEGSettings. On the MC Addin tab, make sure that Skip Commercials is checked. It should be by default.   On the Commercial Skip tab, make sure the Auto Skip option is selected. Click “Save.”   If you try to watch recorded TV before the file conversion and commercial indexing process is complete you’ll get the following message pop up in Media Center. If you click Yes, it will start indexing the commercials if WtvWatcher has already converted it to dvr-ms. Now you’re ready to kick back and watch your recorded tv without having to wait through those long commercial breaks. Conclusion The DVRMSToolBox is a powerful and complex application with a multitude of features and utilities. We’ve showed you a quick and easy way to get your Windows Media Center setup to skip commercials. This setup, like virtually all commercial skipping setups, is not perfect. You will occasionally find a commercial that doesn’t get skipped. Need help getting your Windows 7 PC configured for TV? Check out our previous tutorial on setting up live TV in Windows Media Center. Links Download WTV Watcher Download DVRMSToolBox Download DTBAddin Similar Articles Productive Geek Tips Using Netflix Watchnow in Windows Vista Media Center (Gmedia)Increase Skip and Replay Intervals in Windows 7 Media CenterSchedule Updates for Windows Media CenterIntegrate Hulu Desktop and Windows Media Center in Windows 7Add Color Coding to Windows 7 Media Center Program Guide TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• CodePlex Daily Summary for Monday, March 22, 2010

  CodePlex Daily Summary for Monday, March 22, 2010New Projects[Tool] Vczh Non-public DLL Classes Caller: Generate C# code for you to call non-public classes in DLLs very easily.Artefact Animator: Artefact Animator provides an easy to use framework for procedural time-based animations in Silverlight and WPF.cacheroo: Cacheroo is a social networking community that will make it easier for people who love geocaching to get connected.Data Processing Toolkit: An utility app to collected data from different sources (i.e. bugzilla bug reports) in a structured way. We are currently setting up the site. Mo...eXternal SQL Bridge (PHP): The eXternal SQL Bridge (XSB) allows you to bridge two websites together in a secure manner through pre-shared keys. XSB is resilient against repla...'G' - Language to Define Gestures for Touch Based Applications: A cross plat form multi-touch application framework with a language to define gestures. The application is build on Silverlight 4.0 and the languag...IIS Network Diagnostic Tools: Web implementation of "looking glass" like services (ping, traceroute) as HTTP modules for Internet Information Services.Interop Router: This project establishes a communication framework and job dispatcher for a mixed operating system cluster environment.L2 Commander: L2Commander makes it easier for both new and old l2j users to manage your server.You no longer have to waste time on finding the files you need and...MediaHelper: A utility to help clean up empty/unwanted files and folders in your filesystem.mhinze: matt hinze stuffOneMan: Focus on Silverlight and WCF technology.Rss Photo Frame Android Widget: RSS Photo Frame Android Widget permits showing pictures from any RSS feed on your Android device's desktopSingle Web Session: Web Tool Kits Current project provide developer with different tools that help to enhance web site performance, security, and other common functio...Work Item Visualization: Use DGML to visualize and analyze your TFS Work Items. Included is the ability to perform basic risk/impact analysis. It helps answer the question,...New Releases[Tool] Vczh Non-public DLL Classes Caller: Wrapper Coder (beta): Click "<Click Me To Open Assembly File>", WrapperCoder will load the assembly and referenced assembly. Check the non-public classes that you want...APS - Automatic Print Screen: APS 1.0: APS automatizes the tasks of paste the image in Paint and save it after print screen or alt+print screen. Choose directory, name and file extension...BTP Tools: e-Sword generator build 20100321: 1. Modify the indent after subtitle. 2. Add 2 spaces after subtitle.Combres - WebForm & MVC Client-side Resource Combine Library: Combres 2.0: Changes since last version (1.2) Support ignore Combres pipeline in debug mode - see issue #6088 Debug mode generates comment helping identify in...Desafio Office 2010 Brasil: DesafioOutlook: Controlando um robo com o Outlook 2010dylan.NET: dylan.NET v. 9.4: Adding Platform Invocation Services Support, full Managed Pointer Support, Charset,Dllimport,Callconv setting for P/Invoke, MarshalAs for parametersFamily Tree Analyzer: Version 1.3.2.0: Version 1.3.2.0 Add open folder button to IGI Search Form Fixes to Fact Location processing - IGIName renamed to RegionID Fix if Region ID not fou...Fasterflect - A Fast and Simple Reflection API: Fasterflect 2.0: We are pleased to release version 2.0 of Fasterflect, which contains a lot of additions and improvements from the previous version. Please refer t...IIS Network Diagnostic Tools: 1.0: Initial public release.Informant: Informant (Desktop) v0.1: This release allows users to send sms messages to 1-Many Groups or 1-Many contacts. It is a very basic release of the application. No styling has b...InfoService: InfoService v1.5 - MPE1 Package: InfoService Release v1.5.0.65 Please read Plugin installation for installation instructions.InfoService: InfoService v1.5 - RAR Package: InfoService Release v1.5.0.65 Please read Plugin installation for installation instructions.L2 Commander: Source Code Link: Where to find our source.ModularCMS: ModularCMS 1.2: Minor bug fixes.NMTools: NMTools-v40b0-20100321-0: The most noticeable aspect of this release is that NMTools is now an independent project. It will no longer tied to OpenSLIM. Nevertheless, OpenSLI...SharePoint LogViewer: SharePoint LogViewer 1.5.3: Log loading performance enhanced. Search text box now has auto complete feature.Single Web Session: Single Web Session: !Single Web Session! <httpModules> <add name="SingleSession" type="SingleWebSession.Model.WebSessionModule, SingleWebSession"/> </httpModules>Sprite Sheet Packer: 2.1 Release: Made a few crucial fixes from 2.0: - Fixed error with paths having spaces. - Fixed error with UI not unlocking. - Fixed NullReferenceException on ...uManage - AD Self-Service Portal: uManage v1.1 (.NET 4.0 RC): Updated Releasev1.1 Adds the primary ability to setup and configure the application through a setup wizard. The setup wizard will continue to evol...VCC: Latest build, v2.1.30321.0: Automatic drop of latest buildVS ChessMania: VS ChessMania V2 March Beta: Second Beta Release with move correction and making application more safe for user. New features will be added soon.WatchersNET CKEditor™ Provider for DotNetNuke: CKEditor Provider 1.9.00: Whats New Added New Toolbar Plugin (By Kent Safransk) 'MediaEmbed' to Include Embed Media from Youtube, Vimeo, etc. Media Embed Plugin Added New ...WeatherBar: WeatherBar 1.0 [No Installation]: Extract the ZIP archive and run WeatherBar.exe. Current release contains some bugs that will be fixed in the next version. Check the Issue Tracker...Work Item Visualization: Release 1.0: This is the initial release of the Work Item Visualization tool. There are no known issues when it comes to the visualization aspects of the tool b...WPF Application Framework (WAF): WPF Application Framework (WAF) 1.0.0.10: Version: 1.0.0.10 (Milestone 10): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requi...WPF AutoComplete TextBox Control: Version 1.2: What's Newadds AutoAppend feature adds a new provider: UrlHistoryDataProvider sample application is updated to reflect the new things Bug Fixe...ZoomBarPlus: V2 (Beta): - Fixed bug: if the active window changed while you were in the middle of a single tap delay, long tap delay, or swipe-repeat, it would continue re...Most Popular ProjectsMetaSharpSavvy DateTimeRawrWBFS ManagerSilverlight ToolkitASP.NET Ajax LibraryMicrosoft SQL Server Product Samples: DatabaseAJAX Control ToolkitLiveUpload to FacebookWindows Presentation Foundation (WPF)Most Active ProjectsLINQ to TwitterRawrOData SDK for PHPjQuery Library for SharePoint Web ServicesDirectQPHPExcelFarseer Physics Enginepatterns & practices – Enterprise LibraryBlogEngine.NETNB_Store - Free DotNetNuke Ecommerce Catalog Module

  Read the article

• Using Teleriks new LINQ implementation to create OData feeds

  This week Telerik released a new LINQ implementation that is simple to use and produces domain models very fast. Built on top of the enterprise grade OpenAccess ORM, you can connect to any database that OpenAccess can connect to such as: SQL Server, MySQL, Oracle, SQL Azure, VistaDB, etc. While this is a separate LINQ implementation from traditional OpenAccess Entites, you can use the visual designer without ever interacting with OpenAccess, however, you can always hook into the advanced ORM features like caching, fetch plan optimization, etc, if needed. Just to show off how easy our LINQ implementation is to use, I will walk you through building an OData feed using Data Services Update for .NET Framework 3.5 SP1. (Memo to Microsoft: P-L-E-A-S-E hire someone from Apple to name your products.) How easy is it? If you have a fast machine, are skilled with the mouse, and type fast, you can do this in about 60 seconds via three easy steps. (I promise in about 2-3 weeks that you can do this in less then 30 seconds. Stay tuned for that.)  Step 1 (15-20 seconds): Building your Domain Model In your web project in Visual Studio, right click on the project and select Add|New Item and select Telerik OpenAccess Domain Model as your item template. Give the file a meaningful name as well. Select your database type (SQL Server, SQL Azure, Oracle, MySQL, VistaDB, etc) and build the connection string. If you already have a Visual Studio connection string already saved, this step is trivial.  Then select your tables, enter a name for your model and click Finish. In this case I connected to Northwind and selected only Customers, Orders, and Order Details.  I named my model NorthwindEntities and will use that in my DataService. Step 2 (20-25 seconds): Adding and Configuring your Data Service In your web project in Visual Studio, right click on the project and select Add|New Item and select ADO .NET Data Service as your item template and name your service. In the code behind for your Data Service you have to make three small changes. Add the name of your Telerik Domain Model (entered in Step 1) as the DataService name (shown on line 6 below as NorthwindEntities) and uncomment line 11 and add a * to show all entities. Optionally if you want to take advantage of the DataService 3.5 updates, add line 13 (and change IDataServiceConfiguration to DataServiceConfiguration in line 9.) 1: using System.Data.Services; 2: using System.Data.Services.Common; 3:   4: namespace Telerik.RLINQ.Astoria.Web 5: { 6: public class NorthwindService : DataService<NorthwindEntities> 7: { 8: //change the IDataServiceConfigurationto DataServiceConfiguration 9: public static void InitializeService(DataServiceConfiguration config) 10: { 11: config.SetEntitySetAccessRule("*", EntitySetRights.All); 12: //take advantage of the "Astoria3.5 Update" features 13: config.DataServiceBehavior.MaxProtocolVersion = DataServiceProtocolVersion.V2; 14: } 15: } 16: } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Step 3 (~30 seconds): Adding the DataServiceKeys You now have to tell your data service what are the primary keys of each entity. To do this you have to create a new code file and create a few partial classes. If you type fast, use copy and paste from your first entity,  and use a refactoring productivity tool, you can add these 6-8 lines of code or so in about 30 seconds. This is the most tedious step, but dont worry, Ive bribed some of the developers and our next update will eliminate this step completely. Just create a partial class for each entity you have mapped and add the attribute [DataServiceKey] on top of it along with the keys field name. If you have any complex properties, you will need to make them a primitive type, as I do in line 15. Create this as a separate file, dont manipulate the generated data access classes in case you want to regenerate them again later (even thought that would be much faster.) 1: using System.Data.Services.Common; 2:   3: namespace Telerik.RLINQ.Astoria.Web 4: { 5: [DataServiceKey("CustomerID")] 6: public partial class Customer 7: { 8: } 9:   10: [DataServiceKey("OrderID")] 11: public partial class Order 12: { 13: } 14:   15: [DataServiceKey(new string[] { "OrderID", "ProductID" })] 16: public partial class OrderDetail 17: { 18: } 19:   20: } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Done! Time to run the service. Now, lets run the service! Select the svc file and right click and say View in Browser. You will see your OData service and can interact with it in the browser. Now that you have an OData service set up, you can consume it in one of the many ways that OData is consumed: using LINQ, the Silverlight OData client, Excel PowerPivot, or PhP, etc. Happy Data Servicing! Technorati Tags: Telerik,Astoria,Data Services Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• How to get SQL Railroad Diagrams from MSDN BNF syntax notation.

  - by Phil Factor

  pre {margin-bottom:.0001pt; font-size:8.0pt; font-family:"Courier New"; margin-left: 0cm; margin-right: 0cm; margin-top: 0cm; } On SQL Server Books-On-Line, in the Transact-SQL Reference (database Engine), every SQL Statement has its syntax represented in  ‘Backus–Naur Form’ notation (BNF)  syntax. For a programmer in a hurry, this should be ideal because It is the only quick way to understand and appreciate all the permutations of the syntax. It is a great feature once you get your eye in. It isn’t the only way to get the information;  You can, of course, reverse-engineer an understanding of the syntax from the examples, but your understanding won’t be complete, and you’ll have wasted time doing it. BNF is a good start in representing the syntax:  Oracle and SQLite go one step further, and have proper railroad diagrams for their syntax, which is a far more accessible way of doing it. There are three problems with the BNF on MSDN. Firstly, it is isn’t a standard version of  BNF, but an ancient fork from EBNF, inherited from Sybase. Secondly, it is excruciatingly difficult to understand, and thirdly it has a number of syntactic and semantic errors. The page describing DML triggers, for example, currently has the absurd BNF error that makes it state that all statements in the body of the trigger must be separated by commas.  There are a few other detail problems too. Here is the offending syntax for a DML trigger, pasted from MSDN. Trigger on an INSERT, UPDATE, or DELETE statement to a table or view (DML Trigger) CREATE TRIGGER [ schema_name . ]trigger_name ON { table | view } [ WITH <dml_trigger_option> [ ,...n ] ] { FOR | AFTER | INSTEAD OF } { [ INSERT ] [ , ] [ UPDATE ] [ , ] [ DELETE ] } [ NOT FOR REPLICATION ] AS { sql_statement [ ; ] [ ,...n ] | EXTERNAL NAME <method specifier [ ; ] > }   <dml_trigger_option> ::=     [ ENCRYPTION ]     [ EXECUTE AS Clause ]   <method_specifier> ::=  This should, of course, be /* Trigger on an INSERT, UPDATE, or DELETE statement to a table or view (DML Trigger) */ CREATE TRIGGER [ schema_name . ]trigger_name ON { table | view } [ WITH <dml_trigger_option> [ ,...n ] ] { FOR | AFTER | INSTEAD OF } { [ INSERT ] [ , ] [ UPDATE ] [ , ] [ DELETE ] } [ NOT FOR REPLICATION ] AS { {sql_statement [ ; ]} [ ...n ] | EXTERNAL NAME <method_specifier> [ ; ] }   <dml_trigger_option> ::=     [ ENCRYPTION ]     [ EXECUTE AS CLAUSE ]   <method_specifier> ::=     assembly_name.class_name.method_name I’d love to tell Microsoft when I spot errors like this so they can correct them but I can’t. Obviously, there is a mechanism on MSDN to get errors corrected by using comments, but that doesn’t work for me (*Error occurred while saving your data.”), and when I report that the comment system doesn’t work to MSDN, I get no reply. I’ve been trying to create railroad diagrams for all the important SQL Server SQL statements, as good as you’d find for Oracle, and have so far published the CREATE TABLE and ALTER TABLE railroad diagrams based on the BNF. Although I’ve been aware of them, I’ve never realised until recently how many errors there are. Then, Colin Daley created a translator for the SQL Server dialect of  BNF which outputs standard EBNF notation used by the W3C. The example MSDN BNF for the trigger would be rendered as … /* Trigger on an INSERT, UPDATE, or DELETE statement to a table or view (DML Trigger) */ create_trigger ::= 'CREATE TRIGGER' ( schema_name '.' ) ? trigger_name 'ON' ( table | view ) ( 'WITH' dml_trigger_option ( ',' dml_trigger_option ) * ) ? ( 'FOR' | 'AFTER' | 'INSTEAD OF' ) ( ( 'INSERT' ) ? ( ',' ) ? ( 'UPDATE' ) ? ( ',' ) ? ( 'DELETE' ) ? ) ( 'NOT FOR REPLICATION' ) ? 'AS' ( ( sql_statement ( ';' ) ? ) + | 'EXTERNAL NAME' method_specifier ( ';' ) ? )   dml_trigger_option ::= ( 'ENCRYPTION' ) ? ( 'EXECUTE AS CLAUSE' ) ?   method_specifier ::= assembly_name '.' class_name '.' method_name Colin’s intention was to allow anyone to paste SQL Server’s BNF notation into his website-based parser, and from this generate classic railroad diagrams via Gunther Rademacher's Railroad Diagram Generator.  Colin's application does this for you: you're not aware that you are moving to a different site.  Because Colin's 'translator' it is a parser, it will pick up syntax errors. Once you’ve fixed the syntax errors, you will get the syntax in the form of a human-readable railroad diagram and, in this form, the semantic mistakes become flamingly obvious. Gunter’s Railroad Diagram Generator is brilliant. To be able, after correcting the MSDN dialect of BNF, to generate a standard EBNF, and from thence to create railroad diagrams for SQL Server’s syntax that are as good as Oracle’s, is a great boon, and many thanks to Colin for the idea. Here is the result of the W3C EBNF from Colin’s application then being run through the Railroad diagram generator. create_trigger: dml_trigger_option: method_specifier:   Now that’s much better, you’ll agree. This is pretty easy to understand, and at this point any error is immediately obvious. This should be seriously useful, and it is to me. However  there is that snag. The BNF is generally incorrect, and you can’t expect the average visitor to mess about with it. The answer is, of course, to correct the BNF on MSDN and maybe even add railroad diagrams for the syntax. Stop giggling! I agree it won’t happen. In the meantime, we need to collaboratively store and publish these corrected syntaxes ourselves as we do them. How? GitHub?  SQL Server Central?  Simple-Talk? What should those of us who use the system  do with our corrected EBNF so that anyone can use them without hassle?

  Read the article

• Use Those Extra Mouse Buttons to Increase Efficiency

  - by Mark Virtue

  Did you know that the most commonly used mouse actions are clicking a window’s “Close” button (the X in the top-right corner), and clicking the “Back” button (in a browser and various other programs)?  How much time do you spend every day locating the Close button or the Back button with your mouse so that you can click on them?  And what about that mouse you’re using – how many buttons does it have, besides the two main ones?  Most mouses these days have at least four (including the scroll-wheel, which a lot of people don’t realize is also a button as well).  Why not assign those extra buttons to your most common mouse actions, and save yourself a bundle of mousing-around time every day? If your mouse was manufactured by one of the “premium” mouse manufacturers (Microsoft, Logitech, etc), it almost certain came with driver software to allow you to customize your mouse’s controls and take advantage of your mouse’s special features.  Microsoft, for example, provides driver software called IntelliPoint (link below), while Logitech provides SetPoint.  It’s possible that your mouse has some extra buttons but doesn’t come with its own driver software (the author is using a Microsoft Bluetooth Notebook Mouse 5000, which amazingly is not supported by the Microsoft IntelliPoint software!).  If your mouse falls into this category, you can use a marvelous free product called X-Mouse Button Control, from Highresolution Enterprises (link below).  It provides a truly amazing array of mouse configuration options, including assigning actions to buttons on a per-application basis. Once X-Mouse Button Control is downloaded, its setup process is quite straightforward. Once downloaded, you can start the program via Start / Highresolution Enterprises / X-Mouse Button Control.  You will find the program’s icon in the system tray: Right-click on the icon and select Setup from the pop-up menu.  The program’s configuration window appears: It’s extremely unlikely that we will want to change the functionality of our mouse’s two main buttons (left and right), so instead we’ll look at the rest of the options on the right side of the window.  The Middle Button refers to either the third, middle button (found on some old mouses), or the pressing of the wheel itself, as a button (if you didn’t know you could press your wheel like a button, try it out now).  Mouse Button 4 and Mouse Button 5 usually refer to the extra buttons found on the side of the mouse, often near your thumb. So what can we use these extra mouse buttons for?  Well, clearly Close and Back are two obvious candidates.  Each of these can be found by selecting them from the drop-down menu next to each button field: Once the two options are chosen, the window will look something like this: If you’re not interested in choosing Back or Close, you may like to try some of the other options in the list, including: Cut, Copy and Paste Undo Show the Desktop Next/Previous track (for media playback) Open any program Simulate any keystroke or combination of keystrokes ….and many other options.  Explore the drop-down list to see them all. You may decide, for example, that closing the current document (as opposed to the current program) would be a good use for Mouse Button 5.  In other words, we need to simulate the keypress of Ctrl-F4.  Let’s see how we achieve this. First we select Simulated Keystrokes from the drop-down list: The Simulated Keystrokes window opens: The instructions on the page are pretty comprehensive.  If you want to simulate the Ctrl-F4 keystroke, you need to type {CTRL}{F4} into the box: …and then click OK. Assigning Actions to Buttons on a Per-Application Basis One of the most powerful features of X-Mouse Button Control is the ability to assign actions to buttons on a per-application basis.  This means that if we have a particular program open, then our mouse will behave differently – our buttons will do different things. For example, when we have Windows Media Player open, for example, we may wish to have buttons assigned to Play/Pause, Next track and Previous track, as well as changing the volume with the mouse!  This is easy with X-Mouse Button Control.  We start by opening Windows Media Player.  This makes the next step easier.  Then we return to X-Mouse Button Control and add a new “configuration”.  This is done by clicking the Add button: A window opens containing a list of all running programs, including our recently opened Windows Media Player: We select Windows Media Player and click OK.  A new, blank “configuration” is created: We repeat the earlier steps to assign buttons to Play/Pause, Next track and Previous track, and assign scrolling the wheel to alter the volume:   To save all our changes and close the window, we click Apply. Now spend a few minutes thinking of all the applications you use the most, and what are the most common simple tasks you perform in each of those applications.  Those tasks are then perfect candidates for per-application button assignments. There are many more configuration options and capabilities of X-Mouse Button Control – too many to list here.  We encourage you to spend a bit of time exploring the Setup window.  Then, most important of all, don’t forget to use your new mouse buttons!  Get into the habit of using them, and then after a while you’ll start to wonder how you ever tolerated the laborious, tedious, time-consuming process of actually locating each window’s Close button… Download X-Mouse Button Control Highresolution Enterprise Similar Articles Productive Geek Tips Add Specialized Toolbar Buttons to Firefox the Easy WayBoost Your Mouse Pointing Accuracy in WindowsMake Mouse Navigation Faster in WindowsVista Style Popup Previews for Firefox TabsStupid Geek Tricks: Using the Quick Zoom Feature in Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Download Videos from Hulu Pixels invade Manhattan Convert PDF files to ePub to read on your iPad Hide Your Confidential Files Inside Images Get Wildlife Photography Tips at BBC’s PhotoMasterClasses Mashpedia is a Real-time Encyclopedia

  Read the article

• Hosting WCF service in Windows Service

  - by DigiMortal

  When building Windows services we often need a way to communicate with them. The natural way to communicate to service is to send signals to it. But this is very limited communication. Usually we need more powerful communication mechanisms with services. In this posting I will show you how to use service-hosted WCF web service to communicate with Windows service. Create Windows service Suppose you have Windows service created and service class is named as MyWindowsService. This is new service and all we have is default code that Visual Studio generates. Create WCF service Add reference to System.ServiceModel assembly to Windows service project and add new interface called IMyService. This interface defines our service contracts. [ServiceContract] public interface IMyService {     [OperationContract]     string SayHello(int value); } We keep this service simple so it is easy for you to follow the code. Now let’s add service implementation: [ServiceBehavior(InstanceContextMode=InstanceContextMode.Single)] public class MyService : IMyService {     public string SayHello(int value)     {         return string.Format("Hello, : {0}", value);     } } With ServiceBehavior attribute we say that we need only one instance of WCF service to serve all requests. Usually this is more than enough for us. Hosting WCF service in Windows Service Now it’s time to host our WCF service and make it available in Windows service. Here is the code in my Windows service: public partial class MyWindowsService : ServiceBase {     private ServiceHost _host;     private MyService _server;       public MyWindowsService()     {         InitializeComponent();     }       protected override void OnStart(string[] args)     {         _server = new MyService();         _host = new ServiceHost(_server);         _host.Open();     }       protected override void OnStop()     {         _host.Close();     } } Our Windows service now hosts our WCF service. WCF service will be available when Windows service is started and it is taken down when Windows service stops. Configuring WCF service To make WCF service usable we need to configure it. Add app.config file to your Windows service project and paste the following XML there: <system.serviceModel>   <serviceHostingEnvironment aspNetCompatibilityEnabled="true" />   <services>     <service name="MyWindowsService.MyService" behaviorConfiguration="def">       <host>         <baseAddresses>           <add baseAddress="http://localhost:8732/MyService/"/>         </baseAddresses>       </host>       <endpoint address="" binding="wsHttpBinding" contract="MyWindowsService.IMyService">       </endpoint>       <endpoint address="mex" binding="mexHttpBinding" contract="IMetadataExchange"/>     </service>   </services>   <behaviors>     <serviceBehaviors>       <behavior name="def">         <serviceMetadata httpGetEnabled="True"/>         <serviceDebug includeExceptionDetailInFaults="True"/>       </behavior>     </serviceBehaviors>   </behaviors> </system.serviceModel> Now you are ready to test your service. Install Windows service and start it. Open your browser and open the following address: http://localhost:8732/MyService/ You should see your WCF service page now. Conclusion WCF is not only web applications fun. You can use WCF also as self-hosted service. Windows services that lack good communication possibilities can be saved by using WCF self-hosted service as it is the best way to talk to service. We can also revert the context and say that Windows service is good host for our WCF service.

  Read the article

• Randomly displayed flashing lines, no response to all shortcuts, just power off. [syslog included]

  - by B. Roland

  Hello! I have an old machine, and I want to use for that to learn employees how to use Ubuntu, and to be easyer to switch from Windows. I've been installed 10.04, and updated, but this strange stuff is happend. Graphical installion failed, same strange thing. With alternate workd. Sometimes, when I boot up, a boot message displayed: Keyboard failure..., often diplayed after reboot, and after shutdown, when I haven't plugged off from AC. I replaced the keyboard yet, same failure... If I powered off, and plugged off from AC, no keyboard problems displayed in boot time. Details Configuration: Dell OptiPlex GX60 - in original cover, no changes. 256 MB DDR 166 MHz Intel® Celeron® Processor 2.40 GHz Dell 0C3207 Base Board I know, that is not enough, but I have three other Nec compuers, with nearly similar config, and they works well with 9.10, 10.04, 10.10. Live CDs I've been tried with 10.04 and 10.10, but the problem is displayed too. With 9.10 no strange things displayed, but it froze, during a simple apt-get install. Syslog An error loop is logged here, but I paste the whole startup and error lines. The flashing lines are displayed sometimes immediately after login, but sometimes after 10 minutes, but once occured, that nothing happend. Strange thing is displayed immediately after login: here. An other boot, after some minutes, strange lines, and loop in log appeard: here. The loop should be that: Jan 23 00:20:08 machine_name kernel: [ 46.782212] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 23 00:20:08 machine_name kernel: [ 47.100033] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 23 00:20:08 machine_name kernel: [ 47.100045] render error detected, EIR: 0x00000000 Jan 23 00:20:08 machine_name kernel: [ 47.101487] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 16 at 9) Jan 23 00:20:11 machine_name kernel: [ 49.152020] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 23 00:20:11 machine_name gdm-simple-slave[1245]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Jan 23 00:20:11 machine_name acpid: client 1239[0:0] has disconnected Jan 23 00:20:11 machine_name acpid: client connected from 1247[0:0] Jan 23 00:20:11 machine_name acpid: 1 client rule loaded UPDATE Added syslog things: before errors, error loop, the complete shutdown(after the big updates): Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully called chroot. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully dropped privileges. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully limited resources. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Watchdog thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Canary thread running. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Sucessfully made thread 1337 of process 1337 (n/a) owned by '1001' high priority at nice level -11. Jan 28 20:40:30 machine_name rtkit-daemon[1339]: Supervising 1 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1345 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 2 threads of 1 processes of 1 users. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Sucessfully made thread 1349 of process 1337 (n/a) owned by '1001' RT at priority 5. Jan 28 20:40:32 machine_name rtkit-daemon[1339]: Supervising 3 threads of 1 processes of 1 users. Jan 28 20:40:37 machine_name pulseaudio[1337]: ratelimit.c: 2 events suppressed Jan 28 20:41:33 machine_name AptDaemon: INFO: Initializing daemon Jan 28 20:41:44 machine_name kernel: [ 167.691563] lo: Disabled Privacy Extensions Jan 28 20:47:33 machine_name AptDaemon: INFO: Quiting due to inactivity Jan 28 20:47:33 machine_name AptDaemon: INFO: Shutdown was requested Jan 28 20:59:50 machine_name kernel: [ 1253.840513] lo: Disabled Privacy Extensions Jan 28 21:17:02 machine_name CRON[1874]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 21:17:38 machine_name kernel: [ 2321.553239] lo: Disabled Privacy Extensions Jan 28 22:07:44 machine_name kernel: [ 5327.840254] lo: Disabled Privacy Extensions Jan 28 22:17:02 machine_name CRON[2665]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:32:38 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 22:57:03 machine_name kernel: [ 8286.641472] lo: Disabled Privacy Extensions Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: Called Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: username = [some_user] Jan 28 22:57:24 machine_name sudo: pam_sm_authenticate: /home/some_user is already mounted Jan 28 23:07:42 machine_name kernel: [ 8925.272030] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:07:42 machine_name kernel: [ 8925.272048] render error detected, EIR: 0x00000000 Jan 28 23:07:42 machine_name kernel: [ 8925.272093] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171453 at 171452) Jan 28 23:07:45 machine_name kernel: [ 8928.868041] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:10 machine_name acpid: client 925[0:0] has disconnected Jan 28 23:08:10 machine_name acpid: client connected from 8127[0:0] Jan 28 23:08:10 machine_name acpid: 1 client rule loaded Jan 28 23:08:11 machine_name kernel: [ 8955.046248] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:12 machine_name kernel: [ 8955.364016] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:12 machine_name kernel: [ 8955.364027] render error detected, EIR: 0x00000000 Jan 28 23:08:12 machine_name kernel: [ 8955.364407] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171457 at 171452) Jan 28 23:08:14 machine_name kernel: [ 8957.472025] [drm:i915_gem_idle] *ERROR* hardware wedged Jan 28 23:08:14 machine_name acpid: client 8127[0:0] has disconnected Jan 28 23:08:14 machine_name acpid: client connected from 8141[0:0] Jan 28 23:08:14 machine_name acpid: 1 client rule loaded Jan 28 23:08:15 machine_name kernel: [ 8958.671722] [drm:i915_gem_entervt_ioctl] *ERROR* Reenabling wedged hardware, good luck Jan 28 23:08:15 machine_name kernel: [ 8958.988015] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung Jan 28 23:08:15 machine_name kernel: [ 8958.988026] render error detected, EIR: 0x00000000 Jan 28 23:08:15 machine_name kernel: [ 8958.989400] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 171459 at 171452) Jan 28 23:08:16 machine_name init: tty4 main process (848) killed by TERM signal Jan 28 23:08:16 machine_name init: tty5 main process (856) killed by TERM signal Jan 28 23:08:16 machine_name NetworkManager: nm_signal_handler(): Caught signal 15, shutting down normally. Jan 28 23:08:16 machine_name init: tty2 main process (874) killed by TERM signal Jan 28 23:08:16 machine_name init: tty3 main process (875) killed by TERM signal Jan 28 23:08:16 machine_name init: tty6 main process (877) killed by TERM signal Jan 28 23:08:16 machine_name init: cron main process (890) killed by TERM signal Jan 28 23:08:16 machine_name init: tty1 main process (1146) killed by TERM signal Jan 28 23:08:16 machine_name avahi-daemon[644]: Got SIGTERM, quitting. Jan 28 23:08:16 machine_name avahi-daemon[644]: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.238.11.134. Jan 28 23:08:16 machine_name acpid: exiting Jan 28 23:08:16 machine_name init: avahi-daemon main process (644) terminated with status 255 Jan 28 23:08:17 machine_name kernel: Kernel logging (proc) stopped. Jan 28 23:09:00 machine_name kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 28 23:09:00 machine_name rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="516" x-info="http://www.rsyslog.com"] (re)start Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's groupid changed to 103 Jan 28 23:09:00 machine_name rsyslogd: rsyslogd's userid changed to 101 Jan 28 23:09:00 machine_name rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] When I hit the On/Off button, the system shuts down normally. May be it a hardware problem, but I don't know... Can you say something useful to solve my problem?

  Read the article

• Customize Team Build 2010 – Part 16: Specify the relative reference path

  In the series the following parts have been published Part 1: Introduction Part 2: Add arguments and variables Part 3: Use more complex arguments Part 4: Create your own activity Part 5: Increase AssemblyVersion Part 6: Use custom type for an argument Part 7: How is the custom assembly found Part 8: Send information to the build log Part 9: Impersonate activities (run under other credentials) Part 10: Include Version Number in the Build Number Part 11: Speed up opening my build process template Part 12: How to debug my custom activities Part 13: Get control over the Build Output Part 14: Execute a PowerShell script Part 15: Fail a build based on the exit code of a console application Part 16: Specify the relative reference path As I have already blogged about, it is not intuitive how to specify the paths where the build server has to look for references that are stored in Source Control. It is a common practice to store 3rd party libraries in Source Control, so they are available to everyone, everyone uses the same version of the libraries and updating a library can be done centrally. In Team Build 2010 these paths are specified as a parameter for MSBuild. What we will do in this post is building the values for this parameter based on the values in an argument. You are now pretty aware how to customize the build template, so let’s do the modifications in another way. Instead of opening the xaml file in the workflow designer, we open it in the XML editor. You can open it in the XML Editor by either selecting the Open with menu (see the context menu), or by choosing the View code option. To add this functionality we need to: Specify a new argument Add the argument to the metadata Build the absolute paths for the references and add these paths to the MSBuild arguments 1. Specify a new argument Locate at the top of the document the Members (which are the arguments) of the XAML and add the following line <x:Property Name="ReferencePaths" Type="InArgument(s:String[])" /> 2. Add the argument to the metadata Then locate the line <mtbw:ProcessParameterMetadataCollection> and paste the following line <mtbw:ProcessParameterMetadata Category="Misc" Description="The list of reference paths, relative to the root path in the Workspace mapping." DisplayName="Reference paths" ParameterName="ReferencePaths" /> 3. Build the absolute paths for the references and add these paths to the MSBuild arguments Now locate the place where the assignments are done to the variables used in the agent. And add the following lines after the last Assign activity         <Sequence DisplayName="Initialize ReferencePath" sap:VirtualizedContainerService.HintSize="464,428">           <Sequence.Variables>             <Variable x:TypeArguments="x:String" Name="ReferencePathsArgument">               <Variable.Default>                 <Literal x:TypeArguments="x:String" Value="" />               </Variable.Default>             </Variable>           </Sequence.Variables>           <sap:WorkflowViewStateService.ViewState>             <scg:Dictionary x:TypeArguments="x:String, x:Object">               <x:Boolean x:Key="IsExpanded">True</x:Boolean>             </scg:Dictionary>           </sap:WorkflowViewStateService.ViewState>           <ForEach x:TypeArguments="x:String" DisplayName="Iterate through the paths" sap:VirtualizedContainerService.HintSize="287,206" mtbwt:BuildTrackingParticipant.Importance="Low" Values="[ReferencePaths]">             <ActivityAction x:TypeArguments="x:String">               <ActivityAction.Argument>                 <DelegateInArgument x:TypeArguments="x:String" Name="path" />               </ActivityAction.Argument>               <Assign x:TypeArguments="x:String" DisplayName="Build ReferencePath argument" sap:VirtualizedContainerService.HintSize="257,100" mtbwt:BuildTrackingParticipant.Importance="Low"  To="[ReferencePathsArgument]" Value="[If(String.IsNullOrEmpty(ReferencePathsArgument), &quot;&quot;, ReferencePathsArgument + &quot;;&quot;) + IO.Path.Combine(SourcesDirectory, path)]" />             </ActivityAction>           </ForEach>           <Assign DisplayName="Append the reference paths to the MSBuild Arguments" sap:VirtualizedContainerService.HintSize="287,58">             <Assign.To>               <OutArgument x:TypeArguments="x:String">[MSBuildArguments]</OutArgument>             </Assign.To>             <Assign.Value>               <InArgument x:TypeArguments="x:String">[String.Format("{0} /p:ReferencePath=""{1}""", MSBuildArguments, ReferencePathsArgument)]</InArgument>             </Assign.Value>           </Assign>         </Sequence> Now you can use the template to specify the paths relative to SourcesDirectory. You can download the full solution at BuildProcess.zip. It will include the sources of every part and will continue to evolve.

  Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >