Search Results

Search found 18897 results on 756 pages for 'network connectivity'.

Page 105/756 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Proper Network Infastructure Setup DMZ, VPN, Routing Hardware Question

  - by NickToyota

  Greetings Server Fault Universe, So here's a quick background. Two weeks ago I started a new position as the systems administrator for an expanding health services company of just over 100 persons. The individual I was replacing left the company with little to no notice. Basically, I have inherited a network of one main HQ (where I am situated) which has existed for over 10 years, with five smaller offices (less than 20 persons). I am trying to make sense of the current setup. The network at the HQ includes: Linksys RV082 Router providing internet access for employees and site to site VPN connecting the smaller offices (using an RV042 each). We have both cable and dsl lines connected to balance traffic (however this does not work at all and is not my main concern right now). Cisco Ironport appliance. This is the main gateway for our incoming and outgoing emails. This also has an external IP and internal IP. Lotus domino in and out email servers connected to the mentioned Cisco gateway. These also have an external IP and internal IP. Two windows 2003 and 2008 boxes running as domain controllers with DNS of course. These also have both an external IP and internal IP. Website and web mail servers also on both external and internal IPs. I am still confused as why there are so many servers connected directly to the internet. I am seriously looking to redesign this setup with proper security practices in mind (my highest concern) and am in need of a proper firewall setup for the external/internal servers along with a VPN solution about 50 employees. Budget is not a concern as I have been given some flexibility to purchase necessary solutions. I have been told Cisco ASA appliance may help. Does anyone out in the Server Fault Universe have some recommendations? Thank you all in advance.

  Read the article

• VMware Server Host-Only Network Routing

  - by Chris

  I have a windows 2008 web server machine running VMware server. I have 3 VM's - All 3 are test servers so security isn't really a concern... each of them running windows 2008 standard and some of them serving web content. My ISP only allows one MAC address to access the physical switch, however they give me 10 public IP addresses to use. My question is, if I put each VM on their own Host only network, how can I route all traffic from a specific public IP on the host, to the corresponding host only adapter, therefore routing to the specific VM? For example: A single physical Adapter on the Host has the following public IP's assigned to it in windows networking: 74.208.14.10 74.208.14.20 74.208.14.30 Each VM is on a host-only network vm1 - 192.168.196.1 vm2 - 192.168.197.1 vm3 - 192.168.198.1 On the host, I want to route all traffic from 74.208.14.10 to VM1 and 74.208.14.20 to VM2 and 74.208.14.30 to vm3 without using VMware NAT, or bridged connections. I want each server to appear to have its own public IP address. My guess is i can modify the route tables somehow, or perhaps in ICS...but i'm not sure how.

  Read the article

• How to backup iTunes on Windows to folder/share, i.e. without "Back Up to Disc"? No DVD writer avail

  - by Chris W. Rea

  (Surprised I didn't already find an answer here to this!) I've got a computer on which I'd like to back up the iTunes library – music, movies, apps, everything. We're talking multiple gigabytes. Unfortunately, it seems that iTunes' own built-in "Back Up to Disc" feature (the only backup feature I can find in iTunes) only functions with a CD or DVD writer/burner. The computer in question does not have a DVD burner. While it has a CD burner, attempting to back up to CDs would require dozens of discs plus more time than I'm willing to spend swapping them. So: What is the recommended way to back up an entire iTunes library on a Windows computer, to a non-CD/DVD location such as an external hard drive or a network shared folder? Then, once such a backup has been performed, what is the process for restoring the library – e.g. after the computer has been repaved with a new version of Windows – so that iTunes is resurrected whole and recognizes devices it syncs with? Thank you!

  Read the article

• Win7 Command Prompt drives not available

  - by jmerrill

  I have the opposite problem compared to the author of this question: Hard drive access denied from Windows Explorer (but works from command prompt as Admin) I can see all the drive letters for a particular server in Windows Explorer, and can navigate through them exactly as would be expected. The drive letters are displayed in Explorer in parens to the right of the path info -- finalpathportion (\\server\otherpathportions) (driveletter:) e.g. jmerrill (\\server\users) (H:) But the drive letters are not usable in a "Run as Administrator" command prompt. They have worked in the past, but I have since rebooted. I thought that perhaps I had to start a new command prompt having visited them in Explorer -- but that did not help. "net use" in the command prompt shows Unavailable H: \\server\users\jmerrill Microsoft Windows Network with similar info for the other drives. I can do net use h: /d net use h: \\server\users\jmerrill for each drive, and get the letters to be available in the command prompt. It is perhaps obvious that I don't think that it should be necessary to do that. Does anyone have any ideas?

  Read the article

• How to remap IPs visible from local machine to IPs visible from a machine I have SSH access to?

  - by gooli

  I'm so far out of my depth I don't even know what to google for. There's a server I can connect to via SSH. Via that server I can access other server on its subnet via SSH. What I want to do is be able to access the machines that server has access to directly. Say the server IP is 192.168.7.7 and is the only one in the 192.168.x.x range I have access to. I'd like to configure things in such a way that when I to access say 192.168.7.100 on my machine, the connection will go through an SSH tunnel I open to 192.168.7.7 and out to 192.168.7.100. I would like this to work for any port if at all possible. I know I can set an HTTP proxy and even a SOCKS proxy, but I'm wondering is there is a way to actually remap some of the IP my machine sees to IP only visible from the remote machine. What would this configuration be called? IS this NAT, VPN, IP2IP or something else? How can I set up this on a Windows client box that connects via SSH to a Linux box? Sounds to me like I need to set up some kind of filtering on the network driver or possibly a virtual NIC, but I'm not sure where to go next.

  Read the article

• Windows 7: Setting up backup to an external hard drive on another computer on the network

  - by seansand

  I have an external hard drive connected to a Windows 7 (Home Edition) computer. I have another computer (with Windows 7 Ultimate), and I want to have the Windows 7 Ultimate back up to the same external hard drive, without having to disconnect and move the external hard drive from the Home Edition PC. When I get to the "Set up backup" dialog within Windows 7, it asks me where to save the backup. I select "Save on a network". However, when I enter "\\computername\harddrivename" under Browse, the "OK" button remains grayed out. The button remains grayed out unless I also enter a Username and Password under "Network credentials". However, the account I have on the other computer doesn't have a password for it. To un-gray out the button I must enter a fake password, allowing me to click "OK", but then obviously I get a "bad password" error. Does anyone know how to get around this problem? (Seems kind of ridiculous.) I made sure that the security settings with the external hard drive on the other computer are full access to Everyone, so permissions is not the problem. I also thought about using Homegroup instead of the regular security settings, but there is no obvious way to go about it that way, either.

  Read the article

• Network bridge does not work on Windows 7

  - by D. Strout

  I am trying to use Windows 7 to bridge my wireless and wired connections together to get wireless on a second Windows XP computer (fresh install). The network bridge is created successfully, but when I connect the cable from the first computer with the bridged connections to the second one with just a wired connection, nothing happens. The second computer doesn't connect, and the first computer shows no sign of anything different. I tried bridging the connections of a third computer, and connecting this computer to the second computer. This worked (third computer bridged the wireless to the second computer). Thus, the problem must be with the first (Win 7) computer. However, I have no idea what the problem could be. All Internet Connection Sharing is turned off. Homegroup is disabled (it was originally enabled, I thought that might be a problem, so I disabled it). Also, I had VMWare fusion installed, and that created extra items in the "This connection uses the following items" box in the properties dialog. Thinking this might be causing issues, I uninstalled that too. Still, with everything I tried, I can't get it to work. Any suggestions? Edit: Another thing I noticed that might be worth mentioning: The network icon in the Win7 taskbar has a red X on it that means it's not connected, but when I click the icon, it says connected next to my wireless connection, and I am able to access the internet.

  Read the article

• Different network response for indentical co-located machines

  - by Santosh

  We have a situation as follows: We have a two different virtual machines (VMs) on some remote server farm. The machines are identical in terms of hardware/software(OS) configurations. We have a J2EE application running on JBoss on each of those two machines. These two applications are of different version sav V1 on VM1 and V2 on VM2. We observed some degraded response time for application V2 when accessed via public URL. When we accessed the application through a secured VPN, there is hardly any difference. The bandwidth test (upload/download speed, ping etc) shows that VM1 is responding better when accessed via secured VPN. We concluded that the application does not seem to have performance issue. Because, it that's the case the performance degradation should also be there when access via VPN. So we concluded its the network problem. But since those two identical VMs are on same network we are looking for the reasons for different responses. My question is, given the above situation, what could be reasons for such a behavior ?

  Read the article

• Windows 7 x64 wired connection problem. IP, gateway, dns assigned, can't ping. Network detected as "Network"

  - by Emil Lerch

  I am having a problem connecting to a specific wired network with my Latitude E6410 laptop. Other wired networks seem to work fine, but this one does not. I have a coworker with me with the same Intel 82577LM Gigabit Network card, and he can connect just fine. I've updated to the latest Intel drivers (11.8.75.0) and am not using Pro Set. I obtain all DHCP information just fine (IP, netmask, DNS server, default gateway). I cannot ping anything (internal or on the Internet - I tried pinging Google's public DNS servers by IP 8.8.8.8), nor can I get answers to any DNS queries through NS Lookup. Windows troubleshooting says everything is fine, but I can't get DNS responses. I've seen issues like this in the past that were related to link speed/duplex autonegotiaion failures, so I've tried manually setting link speed/duplex to all values one by one with no success. My coworker is using all default settings, so he is just using autonegotiate. Any ideas of other things to try?

  Read the article

• APC Smart UPS network shutdown issue

  - by Rob Clarke

  Here is a bit about our setup: We have 2x Smart-UPS RT 6000 XL units with network management cards We are running Powerchute from a network server Powerchute is connected to the management cards of both UPSs UPSs are set to do a graceful shutdown via Powerchute when the battery duration is under 20 minutes We also have a command file that runs with Powerchute Although our setup is redundant we do not have an equal load on each server due to APC switches for single power devices The problem is that as we do not have an equal load on each server the batteries drain at different rates. This means that the UPSs both get to the specified low battery duration at completely different times. The problem here is that UPS 1 may have run down to 5 minutes and is in desperate need of initiating a Powerchute shutdown - UPS 2 still has 25 minutes of runtime so no shutdown is initiated. Consequently UPS 1 goes down and takes all the servers with and then shuts down UPS 2 as well! What we need to happen are 1 of either 2 things: Powerchute initiates the shutdown as soon as either UPS reaches the 20 minutes low battery duration setting - and doesnt wait for both The UPS with the heavier load expends its entire battery but does not shutdown both UPSs and lets the load be switched across to the UPS that still has runtime remaining. That way when the UPS that still has runtime reaches its low battery duration it can proceed with the graceful shutdown via Powerchute. Hope that makes sense, any help is greatly appreciated!

  Read the article

• Troubleshoot dropped wireless connections

  - by Jack

  I was recently hired in the IT department of a small company (~180 users) and one of the issues that people have been complaining about is having their wi-fi connections drop during meetings. The company is using an HP ProCurve Wireless LAN with 10 APs and a controller unit located in the server room. I don't have any experience troubleshooting WLAN in a multi-AP environment, so I'm trying to at least gather information using free or cheap tools. I did a basic site survey using the free version of Ekahau HeatMapper and discovered the following in one of the conference rooms that has been a problem. The program picked up three access points (plus a bunch of others with much lower signals that were out of range): AP 1: SSID: "Unknown SSID" - Signal strength: -48 dBm - -40 dBm. Channel: 2 AP 2: SSID "CompanyMain" - Signal strength: -35 dBm or greater. Channel: 2. Security: WEP (This is the main SSID for the company's WLAN.) AP 3: SSID: "CompanyGuest" - Signal strength: -40 dBm - -35 dBm. Channel: 2. Security: WPA2 (This SSID is the company's "guest" WLAN, which was setup to allow Internet access, but prevent network access.) Is there anything that you see that is clearly a problem from the above? I'm assuming that the unknown SSID might be a big problem, and that it is an AP from a neighboring office that is causing interference. Does that seem likely? Also, regarding channel, should we try changing the channels of our APs to avoid interference with that unknown SSID? (Since everything seems to be on Channel 2?) Should our APs be on different channels? In other words, should the CompanyMain and CompanyGuest APs be on different channels? Finally, any recommendations for free/cheap tools to help me figure this out, and/or a good methodology to follow? Thanks in advance for any help. Jack

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• Finding a shared HDD attached to the network from my F-13 machine

  - by Ramy

  Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

  Read the article

• filter / directing URLs coming onto a network

  - by Jon

  Hi all, I an not sure if this is possible or not but what i would like to do is as follows: I have one IP address (dynamic using zoneedit.com to keep it upto date). I have one webserver running my main site which is an Ubuntu machine running Apache. I also have a windows 2008 server running another site. Just to confuse things I also run part of my Apache site on the windows server, currently using proxypassreverse to get the information from it. So it looks something like this: IP 1.2.3.4 maps to mydomain.com as well as myotherdomain.com All requests that come into port 80 are forwarded to the Apache box and I use Virtualhost settings to proxy the windows sites where needed. so mydomain.com is an Apache site mydomain.com/mywindowssection is the Apache server using proxypassreverse to get part of the site from the Windows server myotherdomain.com uses Apache and proxypassreverse to get the whole site. What I would like to be able to do is forward all http requests that come into my network to one machine that figures out who should be serving that content. so: mydomain.com would go to the Apache machine myotherdomain.com would go the windows machine. I am just in the process of setting up an Astaro gateway (never done this before so taking a while to configure) as my firewall, dns, dhcp etc, don't know if this can handle it. I have the capacity to run a VM on the network if a seperate box would be needed for this process as well. Thanks for any and all feedback. Jon

  Read the article

• How to link to a subfolder of a share?

  - by Nicolas Raoul

  On my Windows XP server, a folder called Share2 is shared. It contains a subfolder called folder3. The guest account is protected by a password, which means network users have to type the guest password to access it. When a user types \\server\Share2 in his file explorer, he is prompted for a password. When a user types \\server\Share2\folder3 in his file explorer, an error appears. He is not even prompted for a password. This is problematic because I want to link to this particular folder. How can I link to folder3? Notes: - Both Desktop shortcuts and HTML links in IE7/8 give an error if I link to folder3, but work if I just link to Share2. - Using the file:// syntax instead of the \\ syntax leads to the same results. - Password setting per http://www.lancelhoff.com/how-to-password-protect-a-shared-folder - Not using "Simple File Sharing" - The error message is ???????????????????????? which means "could not find it. check the path and try again". No English Windows around to try, sorry! It is easy to reproduce the problem though, so can anyone post the English error message for the sake of searchability? Thanks!

  Read the article

• Fedora 12 on Vmware network disabled on restore

  - by Chaitanya

  I have a fedora 12 guest running on VMWare on windows 7. I use it mainly for the occasional linux dev. Whenever I restart the guest, networking works fine. But if I close the VMware player and save state, the next time I start the image, networking is disabled (red x on the network icon. message saying networking disabled). I can't seem to find a way to restore networking. I have to reboot the guest to get my network access back again. My Ubuntu image doesn't have this problem. I can close the player and when I re run the image, I can pick up where I left off, with all the open firefox windows and application windows as I left them. Fedora saves state, but doesn't seem to enable networking. There is a relevant warning I have seen "SELinux is preventing /sbin/ifconfig "read" access to/var/run/vmware-active-nics." But I am not sure how to solve it. I know fedora isn't officially supported by VMware, but it seems to be working fine for the most part and meeting my needs, except for this one little issue. Any help would be much appreciated.

  Read the article

• Is UPS worthwhile for home equipment?

  - by Jon Skeet

  Over the years, I've had to throw away a quite a few bits of computing equipment (and the like): Several ADSL routers with odd symptoms (losing wireless connections, losing wired connections, DHCP failures, DNS symptoms etc) Two PVRs spontaneously rebooting and corrupting themselves (despite the best efforts of the community to diagnose and help) One external hard disk still claiming to function, but corrupting data One hard disk as part of a NAS raid array "going bad" (as far as the NAS was concerned) (This is in addition to various laptops and printers dying in ways unrelated to this question.) Obviously it'll be impossible to tell for sure from such a small amount of information, but might these be related to power issues? I don't currently have a UPS for any of this equipment. Everything on surge-protected gang sockets, but there's nothing to smooth a power cut. Is home UPS really viable and useful? I know there are some reasonably cheap UPSes on the market, but I don't know how useful they really are. I'm not interested in keeping my home network actually running during a power cut, but I'd like it to power down a bit more gracefully if the current situation is putting my hardware in jeopardy.

  Read the article

• Windows 7, network shares, and authentication via local group instead of local user

  - by Donovan

  I have been doing some troubleshooting of my home network lately and have come to an odd conclusion that I was hoping to get some clarification on. I'm used to managing share permissions in a domain environment via groups instead of individual user accounts. I have a box at home running windows 7 ultimate and I decided to share some directories on that machine. I set it up to disallow guest access and require specifically granted permissions. (password moe?). Anyway, after a whole bunch of time i figured out that even though the shares I created were allowed via a local group i could not access them until i gave specific allowance to the intended user. I just didn't think i would have to do that. So here is the breakdown. Network is windows workgroup, not homegroup or nt domain PC_1 - win 7 ultimate - sharing in classic mode - user BOB - groups Admins PC_2 - win 7 starter - client - user BOB - groups admins PC_3 - win xp pro - client - user BOB - groups admins the share on PC_1 granted permission to only the local group administrators. local user BOB on PC_1 was a member of administrators. Both PC_2 and PC_3 could not browse the intended share on PC_1 because they were denied access. Also, no challenge was presented. They were simply denied. After adding BOB specifically to the intended share everything works just fine. Remember, its not an nt domain just a workgroup. But still, shouldn't i be able to manage share permissions via groups instead of individual user accounts? D.

  Read the article

• Force Juniper-network client to use split routing

  - by craibuc

  I'm using the Juniper client for OSX ('Network Connect') to access a client's VPN. It appears that the client is configured to not use split-routing. The client's VPN host is not willing to enable split-routing. Is there a way for me to over-ride this configuration or do sometime on my workstation to get the non-client network traffic to by-pass the VPN? This wouldn't be a big deal, but none of my streaming radio stations (e.g. XM) work will connected to their VPN. Apologies for any inaccuracies in the terminology. ** edit ** The Juniper client changes my system's resolve.conf file from: nameserver 192.168.0.1 to: search XXX.com [redacted] nameserver 10.30.16.140 nameserver 10.30.8.140 I've attempted to restore my preferred DNS entry to the file $ sudo echo "nameserver 192.168.0.1" >> /etc/resolv.conf but this results in the following error: -bash: /etc/resolv.conf: Permission denied How does the super-user account not have access to this file? Is there a way to prevent the Juniper client from making changes to this file?

  Read the article

• Network card very slow, only on Windows

  - by J Penguin

  This only happens to 1 of my machine, and only when booting into Windows 7. No matter what network card I put in, Windows would default its mode to 10Mbps full duplex. Transfer speed is approximately 1 MB/s. If I set it to 100Mbps, the transfer drops to 100-200K/s. If I set it to 1000Mbps, the connection is lost completely. I've tried swapping in different cards, both PCI-E and PCI. I'v etried update the windows, I've tried reinstalling the drivers... On this very same machine, if I boot into Fedora, it can use the card at its full capacity 1000Mbps transfering 80+ MB/s And all the cards work just fine when plugging into other machines on the same network. I'm very curious. What could be the reason for this? The only different software that this machine has is virtual box with a VPN emulator, but disabling that VPN doesn't seem to do anything. I would like to get this fixed, hopefully, without reinstalling windows _< Will that be possible?

  Read the article

• What is the best way to connect a 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• What is the best way to connect 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >