Search Results

Search found 18897 results on 756 pages for 'network connectivity'.

Page 106/756 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• Show full URI/URL in Chrome's developer tools Network tab

  - by Lev

  When using Chrome to debug, I find it incredibly difficult to be efficient due to the fact that I don't see how I can force the "Network" tab of the developer tools to show the full request URI. It will show the full URI if you hover the link and wait a second, but this is incredibly counterproductive. All of my AJAX requests are sent to ajax.php, and handled by using query string arguments, like: ajax.php?do=profile-set ajax.php?do=game-save ... etc. Since I use AJAX extensively, my network tab is filled with "ajax.php", but I have to manually hover each and every entry to find the request I am looking for. Surely there has got to be another way!? I am constantly fed up by something new in Firefox and immediately force myself back into Chrome, but it is always the developer tools in Chrome that keep me from using it for an extended period of time. Hopefully I can find out how to do this so I can continue using Chrome as my numero uno. I've provided a screen shot to show you where I mean:

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• scalable yet doable small-medium office network

  - by Jared

  Hello, I'm studying up with both Microsoft and Cisco literature and I must say, my head is starting to get clustered up (pun intended). I've made a quick network diagram of a theoretical company... Company1 owns Company 2 and Company 3, which are all under separate rooms and networks, but must be able to share a few resources such as files or printers. Given the amount of info out there and best practices, I thought about posting here to get suggestions and see what would the pro's do. I can read and read all day and implement on my own, but if I dont get some outside input, how will I know if I'm doing something wrong, right? anyway, please take a look and see if this is an over-complicated network or a lackluster design for a small-medium company of about 35 people and lets say they will be double that number by end of the year... :) Using win2k3, esxi, windows xp. FCS - forefront client security, ACS - access control system, SPCWK - spiceworks, XCH - Exchange Im not allowed to post an image yet, so here's the link ---- GLIFFY IMAGE Flame suit is on just in case people get mad at me for making an "abomination". I'd really want to get the general overview properly before I dive into the more complicated things

  Read the article

• Can a folder on a NAS be made available as a physical drive in VMWare?

  - by asbjornu

  We are currently in the process of moving from a single web server to two load balanced web servers and are facing some challenges we don't quite know how to fix. One of these is that the current single server hosts applications that write stuff to disk. The applications running on the server expects that when something is written to disk it later will in fact exist, so it's important that this premise is fulfilled with the dual server architecture as well. The dual server setup is a couple of VMWare instances with Windows Server 2008 R2 as the guest operating system. Out of the box, these instances does not share any kind of file system, so just moving the applications over would make them break since one instance would write something to the file system that doesn't exist on the other. Thus we need to share a file system between the two virtual servers. Our host has proposed to create a network share on a SAN and map this share individually on each virtual machine. This doesn't work too well due to NTFS permissions, etc., because the share needs to be accessed by several independent web applications that won't even be in the same application pool. The only solution that kind of works is to hard code an "identity" for each web application into its web.config file, but this means password in clear text which doesn't sit well with me. Since the servers are virtual, I'm thinknig: Wouldn't it be possible to make a NAS area available as a physical disk in the gues operating system somehow? Since VMWare has full control of the virtual hardware, you'd think it would be able to "fake" a local hard drive in the virtual machine that in reality is a folder on a NAS, but so far I haven't found anything that states how and if this is possible. So I have to ask the wonderful Server Fault community: Can a folder on a NAS be made available as a physical drive (typical D:) in both of the virtual machines?

  Read the article

• Destination NAT Onto the Same Network from internal clients

  - by mivi

  I have a DSL router which acts as NAT (SNAT & DNAT). I have setup a server on internal network (10.0.0.2 at port 43201). DSL router was configured to "port forward" (or DNAT) all incoming connections to 10.0.0.2:43201. I created a virtual server for port forwarding on DSL router. I also added following iptables rules for port forwarding. iptables -t nat -A PREROUTING -p tcp -i ppp_0_1_32_1 --dport 43201 -j DNAT --to-destination 10.0.0.2:43201 iptables -I FORWARD 1 -p tcp -m state --state NEW,ESTABLISHED,RELATED -d 10.0.0.2 --dport 43201 -j ACCEPT # ppp_0_1_32_1 is routers external interface. # routers internal IP address is 10.0.0.1 and server is setup at 10.0.0.2:43201 Problem is that connections coming from external IP addresses are able to access internal server using External IP address, but internal clients (under NAT) are not able to access server using external IP address. Example: http://<external_address>:43201 is working from external clients But, internal clients are not able to access using http://<external_address>:43201 This seems to be similar to the problem described in http://www.netfilter.org/documentation/HOWTO/NAT-HOWTO-10.html (NAT HOW-TO Destination NAT Onto the Same Network). Firstly, I am not able to understand why is this a problem for internal clients? Secondly, what iptables rule will enable internal clients to access server using external IP address? Please suggest.

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• Windows 7, Printer is unavailable until PC reboot

  - by Cjs

  We are having a problem that I haven't seen before and can find no answers to online. A desktop running Windows 7 is unable to print using network printers. When the user tries, no matter what printer it is, he get's the following message when using Microsoft Office applications: "Current printer is unavailable. Select another printer." When the end user uses Outlook we get the message: "Printing is not available. There are no printers installed. You can select and configure a printer in Windows Control Panel." Now here is the confusing part, if we reboot the pc it works fine for a little while and then goes back to the same old same old. The printers are working fine for every other user as well so I believe it is the user's machine. If anyone has any ideas please let me know. Edit: I'd like to add in that some people were having luck disabling snmp for the printers. Restarting the print spooler doesn't seem to do anything.

  Read the article

• Connection to Google, Yahoo, Bing, Ask, etc. compromised via all devices on my home network - How?

  - by jt0dd

  I'm a very computer savvy guy (although not very networking savvy), and I may still be wrong about this, but I think my home network may be compromised somehow. I'd like to know if it's possible for someone to have hijacked my network's connection to Google.com and other popular websites. Update: The issue seems to take effect with all popular websites. I can connect to small (non-popular) websites without issue, but Facebook, Google, Yahoo, and Bing cannot be accessed by any device on my home network. On all devices using my home network, I'm being shown http://www.google.com WARNING! Internet Explorer is currently out of date. Please update to continue. when I attempt to connect to google.com. I wouldn't be surprised by this at all if it were just the laptop. It's the fact that this is happening on all devices on my network that confuses me. Here's the screenshot from my iPhone, for reference. Can my home network be compromised? Is that even possible? How can something like this happen across all platforms on all devices in the same way? I wouldn't imagine every device / platform on the network would get the same virus. Should I assume that my network's security is totally compromised? Update: All mobile devices and laptops on my home network are experiencing the same alert when attempting to connect to google.com.

  Read the article

• Reliable backup software for windows network/samba shares.

  - by Eli

  Hi All, I have a Win2003 server that works as a pdc for a number of XP boxes, and a couple related FreeBSD boxes. I need to back up roaming profiles, non-roaming profiles via network shares, local hard drive data, and files on the FreeBSD boxes via samba shares. I have tried Genie Backup Manager and Backup4All pro, and both have excellent features, but both also begin to fail disastrously with more than a few days use. Mostly, the errors seem to have been from the backup catalog getting out of synch with itself. Whatever it is, there is no excuse for a backup software that says it backed up files when it really didn't, or the log saying it backed up exactly the same file 10,000 times in a single run, or flat-out crashing, or any of the other myriad problems I've run into with these. Really sad for products that fill such an important need. Anyway, does anyone know of a backup software that works reliably and can do the following? Scheduled backups for multiple jobs, without a user logged in. Backup from local hard drives or network shares. Incremental backups. Thanks! Edit: Selected solution: I've added my (hopefully final) solution as an answer.

  Read the article

• XenServer VMs can't reach network

  - by toto

  I'm currently trying to setup a small cloud architecture , I'm using in the installation CloudStack 2.2.14 which need two node : a management server (as node1) to provision the cloud and a hyperviser XenServer 5.6 SP2 to host the VMs (as node2). I succeded to create both node1 and node2 into an ESXi 5 VMWare as VMs. So The ESXi 5 is hosting two VMs node1 + node2 , and node2 which is the XenServer will host also VMs (such as ubuntu or Centos). Both node1 and node2 can ping each other and can get the internet connection from Esxi5 ,but My problem is : that VMs into the node2(XenServer) can't reach the network (can't ping node1 or Esxi or get an internet connection but they can ping VMs IN the node2(XenServer). So I tried to: 1-Setup a DHCP server as node3 in ESXi5 and connect node2(Xenserver) to him , but always the VMs into to node2 can't reach the outer network. 2-Setup a DCHP server into node2 , but always the same problem. So , 1-is there any other configuration i'm missing in node2 (considering that I'm sure about DNS , GW , NETMASK configuration)?. 2-Is it the problem because i'm Creating VMs into node2(XenSever) which is a VM into ESXi 5 ?

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Route specific network traffic through vpn in virtualbox guest

  - by Sander

  I am running OSX with a windows server 2008 guest in Virtualbox. My goal is to route some of the network traffic in the host through the server guest. This is because the win2008 server has a VPN connection to my workplace using a Smartcard solution which can not operate on OSX. My current set-up is like this: OSX (Host): connected to the internet via en01 Win2008 (Guest): connected to the internet using NAT (lan1 in guest) has a SSTP VPN connection to my workplace is connected to the guest using an Host Only Adapter vboxnet0 (LAN2 in guest) The important part is about the host (OSX). Primarily I want all network traffic to just go through en01. However, all traffic which can only be accessed through the VPN must go through the guest and through the VPN. I have one specific FQDN which can only be accessed through the VPN (say corp.mycompany.com). I do not know much about networking. I thought I would be able to get it to work by bridging together LAN2 and LAN1 but this didn't seem to work this: http://archives.aidanfindlater.com/blog/2010/02/03/use-vpn-for-specific-sites-on-mac-os-x/ using a loopback adapter on WinXP (when I did not have win2008 yet, but this doesn't work because I can't create a PPTP connection) And I've also read about Routing and Remote Access but I have no idea on how to use this. Can someone help me in the right direction?

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

• Sharing music on NAS with other zunes and ipods

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40gb worth of music and my girlfriend has her iPod music library around 30gb. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (zune/ipod) seamlessly.

  Read the article

• Configure a Windows PC as network appliance w/o monitor, keyboard and mouse

  - by Joshua Lim

  I intend to use a small form factor PC with Windows 7 Professional installed as a network appliance attached directly to my customer's LAN without connecting a monitor, keyboard or mouse. How should I configure the networking for my PC so that I can access it via say my laptop? I figure that I can do it 2 ways. Attach my laptop to the PC using a crossover cable? Connect via RDP and configure networking. Configure an IP address on the PC before I deliver it to the customer place. At the customer's place, attach the PC to LAN and connect to the IP address which I previously configured from my laptop or from one of the customer's workstations. I know the first way is doable, but is the second way possible? I'm sorry if this question sounds ridiculous - I am Delphi programmer but a novice on networking. Finally, if possible, I hope to make the configuration process web based as I wouldn't like to reveal the fact that I am using Win7 Pro for the network appliance!

  Read the article

• High speed network configuration

  - by Peter M

  Sorry if this seems to be a stupid question, I'm not sure how to specify what I want to know when checking google. I will have 2 or 3 devices pumping out data on a 100Base-T port. The combined data rate of all devices is about 15KB/S which exceeds the optimal 100Base-T channel capacity (12KB/S), but well within the realms of a 1000Base-T connection. Each device will be sending a burst of data in the form of an FTP transfer to a common, single host computer in a sequential manner ie: Device A establishes FTP connection and transfers data Device B establishes FTP connection and transfers data Device C establishes FTP connection and transfers data It may be that the A&B, B&C and C&A transfers overlap in the time domain to some extent. There will be minimal traffic going back from the computer to each device (in general what ever is needed to support the FTP transfers), and the network will be dedicated to transferring data between these devices and the host computer. Is it possible to use a switch to combine the multiple incoming 100Base-T streams into a single outgoing 1000Base-T stream? if so what features in a switch should I be looking for? Or would it be better to have 3 physical point-to-point 100Base-T dedicated connections between each device and the host computer? (thus having at least 3 physical Ethernet interfaces on that computer) Note that I can't change the interface on the devices, but I am free to choose the network and host computer configuration. Thanks for you help Peter

  Read the article

• Moving Microsoft Exchange server to the private network.

  - by Alexey Shatygin

  In one of the offices, we have a 50-computers network, which had only one server machine: Windows 2003 Server Microsoft ISA Server Microsoft Exchange 2003 This server worked as a gateway (proxy server), mail server, file server, firewall and domain controller. It had two network interfaces, one for WAN (let's say 222.222.222.222) and one for LAN (192.168.1.1). I set up a Linux box to be the gateway (without a proxy), so the Linux box now has the following interfaces: 222.222.222.222 (our external IP, we removed it from the Windows machine) and 192.168.1.100 (internal IP), but we need to keep the old Windows server as a mail server and a proxy for some of our users, until we prepare another Linux machine for that, so I need the mail server on that machine to be available from the Internet. I set up iptables rules to redirect all the incoming connections on the 25th and 110th ports of our external IP to 192.168.1.1:25 and 192.168.1.1:110 and when I try to telnet our SMTP service telnet 222.222.222.222 25 I get the greetings from our windows server's (192.168.1.1) SMTP service, and that's works fine. But when I telnet POP3 service telnet 222.222.222.222 110 I only get the blank black screen and the connection seem to disappear if I press any button. I've checked the ISA rules - everything seems to be the same for 110th and 25th ports. When I telnet on 110th ports of our Windows server from our new gateway machine like this: telnet 192.168.1.1 110 I get the acces to it's POP3 service: +OK Microsoft Exchange Server 2003 POP3 server version 6.5.7638.1 (...) ready. What sould I do, to make the POP3 service available through our new gateway?

  Read the article

• How Does EoR Design Work with Multi-tiered Data Center Topology

  - by S.C.

  I just did a ton of reading about the different multi-tier network topology options as outlined by Cisco, and now that I'm looking at the physical options (End of Row (EoR) vs Top of Rack(ToR)), I find myself confused about how these fit into the logical constructs. With ToR it also maps 1:1: at the top of each rack there is a switch(es) that essentially act as the access layer. They connect via fiber to other switches, maybe chassis-based, that act as the aggregation layer, that then connect to the core layer. With EoR it seems that the servers are connecting directly to the aggregation layer, skipping the access layer all together, by plugging directly into what are typically chassis switches. In EoR then is the standard 3-tier model now a 2-tier model: the servers go to the chassis switch which goes straight to the core switch? The reason it matters to me is that my understanding was that the 3-tier model was more desirable due to less complexity. The agg switch pair acts as default gateway and does routing; if you use up all of your ports in your agg layer pair it's much more complicated to add additional switches, than simply adding more switches at the access layer. Are there other downsides to this layout? Does this 3-tier architecture still apply in some way in EoR? Thanks.

  Read the article

• Shared Files stuck locked even after closing all sessions

  - by Chris S

  We run a business app from a shared network drive (has to be this way). When I go to do updates it complains that files are locked. Generally there are open sessions from people who left their computer on, but with no locks on files; there aren't necessarily always sessions open when it complains about locked files. If I close these sessions they disappear. I say "disappear" because I suspect they're actually hanging open. If I try to restart the Server service, it hangs on stopping. Restarting the whole server (it's a VM) unlocks the files. The Server is a Windows 2008 R2 Ent VM running on Hyper-V; the share is accessed through DFS. Offline Files and caching are disabled (Share and GPO). All clients are Win7. Nothing has SP1 yet. Any ideas on what causes the file locks to hang? Any ideas for a solution other than rebooting the server every time?

  Read the article

• How can I redirect/forward all the UDP/TCP traffic on one interface to another interface in OpenWrt

  - by Sina Sou

  I am new to networking and I have a measurement device (D) that periodically sends all its readings over few UDP multicast sockets (with different multicast IP addresses and different port numbers). That device even listens to a TCP socket simultaneously to modify its configuration on port 7234. Since the device has just a Ethernet interface for communication and I want to make it work wireless, I decided to use a very small wireless open-wrt based router that attaches to the device (D) and redirect/forward all the network traffic(Both UDP/TCP) to the router wireless interface. In order to simplify the problem assume that the Device (D) establishes following sockets (at the same time) UM_SOCK1: UDP mcast socket on 239.1.2.3 port# 50620 UM_SOCK2: UDP mcast socket on 239.1.2.4 port# 50640 TC_SOCK3: TCP DHCP/STATIC ip address 192.168.1.200 port 7234 And (D) is connected to Open-Wrt router (R) via interface en01 (Ethernet) the router has it own wireless interface on (wlan0) I want all the traffic from interface pass through wlan01 and vice versa (bi-directional) en01 <---- wlan01 What would be the minimum iptables or ... commands that I need to make this possible? Even I am wondering if traffic directing can be made easier like if the direction is not going to be based on IP addresses(not desired if the device is connected via DHCP) I would rather redirection to be Interface(en0) based or on MAC address (The best solution since my device has unique MAC address)? Thanks

  Read the article

• Windows network routing

  - by fabianvilers

  Hi! I'm working by my customer premises and they let me connect my private laptop on a dedicated Wi-Fi for internet access. It's nice for external consultants. The only issue is that we can't connect on a remote server on port 25. I suppose this policy is set up to avoid infected computers sending spam from their network. As you can have guessed, this is something weird that I can't send mail at all. Fortunately, I've a 3G cell phone that I can connect by Bluetooth on my laptop. So when I want to send an e-mail, I have to disconnect from Wi-Fi, connect my phone, send the e-mail, disconnect phone and reconnect Wi-Fi. Kinda overhead. My question is: how can I tell Windows 7 to use the Wi-Fi for every out connection, but if it's a connection on port 25, use the cell phone network? With this solution, I could let my phone connected all day without having to switch again and again. Thanks a lot for your anwwers. Fabian

  Read the article

• Can't find PC on network

  - by Simon Verbeke

  I just got myself a new laptop, and set it up. It is connected to the wireless internet in my home. I then wanted to create a homegroup between the laptop and my desktop, but they can't find each other. Probably because the desktop has a wired connection to the router and the laptop is connected to a wireless access point. The router and the AP are connected to a switch in the middle by cable. A sketch of the network: Laptop - - - Wireless Access Point ----- Switch ----- Router ----- Desktop ^ ^ ^ ^ Wireless Wired Wired Wired They both point to the same gateway and DHCP-server (on 192.168.0.1). And I can ping to that address from both PCs. When I try to ping either of the PCs the pings time out. The subnets are also the same (255.255.255.0) and the IPs are in the same range (192.168.0.114 laptop, 192.168.0.205 desktop). So I don't really understand what I need to do to be able to access either computer from the other. The weird thing is that Synergy (to use mouse and keyboard over the network) works, just by using the IPs assigned to both PCs. The acces point is a linksys WAP54g, but I'm unsure of the Router, it has a custom casing from our ISP and hides any clues for identifying the product. I'm going to google a bit so I can add that info later. Both PC's are Windows 7 64 bit. The desktop is Ultimate, the laptop Professional.

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >