Search Results

Search found 5373 results on 215 pages for 'wireless bridge'.

Page 105/215 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• What can I do to configure my SSH such that it pauses for a flaky connection?

  - by kfmfe04

  I run ssh from OSX to a Ubuntu box - under home WIFI, everything works perfectly. However, when I ssh from certain external networks, ssh may be working fine for a minute or two and then drop due to a flaky network (diagnosed by pinging 8.8.8.8). How can I set up ssh so that it simply waits/pauses rather than drop (when dropping, I have to setup my development environment from scratch - a big hassle). EDIT When I say a bad connection, I mean, for example, ping 8.8.8.8 will work fine for a while, and then fail for 40-50 pings, and then come back on again.

  Read the article

• putty ssh client become not responding frequently in windows 7

  - by Sankaran

  with celeron processor and 512 MB ram windows 7 takes too much time even to open a folder in windows explorer. I connect to internet with GPRS modem. When I tried to connect with remote linux machine with putty ssh client. The problem is the putty becomes Not responding in 2 or 3 minutes. I've to connect again and putty goes Not responding again. When i tried in Safe mode with networking, GPRS modem is not even detected. the modem is USB data card. Is it possible load USB drive in safe mode of windows 7 or any other possibility to connect with remote machine via ssh

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• Slow WLAN file transfer between server and tablet

  - by user266985

  My file server is running Ubuntu 12.04 and I'm sharing files from it over samba. It is connected via gigabit ethernet. My desktop, running Windows 8.1, is also connected via gigabit ethernet. I can transfer files between the two and completely saturate that gigabit pipe. However, I just got a Surface Pro 2, and I'm trying to stream HD movies from my server to the device over WiFi. For some reason, I can't break much past 1.5MB/s transferring files over the network. I've tried streaming through XBMC and a standard file copy; no difference. To add the confusion, if I connect to my guest network and then use my VPN server (installed on the router) to access the file server, I get around 3.2MB/s. I've been running diagnostics to determine the root and I think I've found it but I have no idea what is causing it or how to fix it. Router: Asus RT-N66U Surface Pro 2 Network Card: Marvell Avastar 350N (Driver 19/09/2013 v14.69.24044.150) InSSIDer: Link Score: 100 Co-Channels: 0 Overlapping: 0 5GHz Network Channel: 48+44 iperf File Server as Server; Surface Pro 2 as Client - TCP Performance: Acceptable ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 192.168.0.90 port 5001 connected with 192.168.0.56 port 57367 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 10.1 MBytes 84.7 Mbits/sec [ 4] 1.0- 2.0 sec 10.4 MBytes 87.6 Mbits/sec [ 4] 2.0- 3.0 sec 10.6 MBytes 88.8 Mbits/sec [ 4] 3.0- 4.0 sec 10.7 MBytes 89.5 Mbits/sec [ 4] 4.0- 5.0 sec 10.1 MBytes 84.4 Mbits/sec [ 4] 5.0- 6.0 sec 10.2 MBytes 85.8 Mbits/sec [ 4] 6.0- 7.0 sec 7.04 MBytes 59.1 Mbits/sec [ 4] 7.0- 8.0 sec 10.8 MBytes 90.2 Mbits/sec [ 4] 8.0- 9.0 sec 10.6 MBytes 89.1 Mbits/sec [ 4] 9.0-10.0 sec 8.62 MBytes 72.3 Mbits/sec [ 4] 0.0-10.0 sec 99.2 MBytes 83.1 Mbits/sec iperf Surface Pro 2 as Server, File Server as Client Performance: Poor ------------------------------------------------------------ Client connecting to 192.168.0.56, TCP port 5001 TCP window size: 22.9 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.0.90 port 40233 connected with 192.168.0.56 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 1.0- 2.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 2.0- 3.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 3.0- 4.0 sec 1.25 MBytes 10.5 Mbits/sec [ 3] 4.0- 5.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 5.0- 6.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 6.0- 7.0 sec 1.38 MBytes 11.5 Mbits/sec [ 3] 7.0- 8.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 8.0- 9.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 9.0-10.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 0.0-10.1 sec 15.0 MBytes 12.4 Mbits/sec For some reason, it gets capped and I haven't got a clue why. Any suggestions? Edit: My link speed is reported as 270Mbps by Windows. I'm less than two metres from the router with a clear line of sight.

  Read the article

• How do you use Time Capsule for MAC controlled Internet?

  - by Kevin Perttula

  I'm using an Internet Provider that requires a username and password to log in; the prompt shows up as soon as you open a web browser. Because of this, I can only have one device online at a time. How can I get my Time Capsule to essentially log in as the user and allow other devices to connect through it. My Time Capsule has worked with other ISPs that don't require the user log in, but I recently moved. I may be wrong about how the ISP is allowing access, I wasn't sure how to describe the problem. Thanks.

  Read the article

• Sagem Router Wifi Key Issue

  - by user23392

  Hi I have a multiservices sagem router which supports wifi as well, the pack came up with a default wifi configuration key and a WEP Key in the label of the package like this: WIFI Configuration key: abcd1234 WEP Key: C4H2F167C10263AEB98V52920E Now, when i execute the wifi usb wizard in the official cd, it asks me for the WIFI key, i put the abcd1234 & it says it's incorrect, i try the long WEP key and it says that the key should only have 8 characters. When i go to the control panel of the router in the wifi config, i see that: Open Authentification System WEP 128 Bit Passphrase: C4H2F167C10263AEB98V52920E Now since the wizard only accepts 8 characters, i try to change the 128bit to 64bit and put some 8 characters and it ends up saying that the new key should be 5 or 13, or 10-26 hex numbers. What to do? Thanks

  Read the article

• how can i share my laptop 3g connection with another laptop using wifi?

  - by user23392

  Hello. i have an intel laptop with wifi running windows vista , and connected to internet using Huawei 3g key, can i share this connection using wifi with another laptop/device ? i can't find an Ad Hoc Wi-Fi Network option , maybe because i'm not using a wired connection. Any solution? Thanks

  Read the article

• An device with an unknown MAC address is connected to my router

  - by Yar

  There is a computer that is not mine that is accessible on my network. I can even access its filesystem via AFP. What I want to know is how the computer could get on my network. My network is secured like this: Does that mean that they've used password cracking tools? The pass is not easy to guess but not hard to figure out via brute-force hacking, I guess. If I am being hacked, should I switch to WPA?

  Read the article

• RTL8188CE doesn't connect to any wifi access points

  - by Drakmail

  I'm using network manager to connect. Also, tryed iwconfig. Results are same. I even try to connect to open access point — results are same. More information: Drakmail@thinkpad-x220:~$ lspci | grep Network | grep -v Ethernet 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Drakmail@thinkpad-x220:~$ uname -a Linux thinkpad-x220 3.1.0 #1 SMP PREEMPT Wed Oct 26 02:19:49 UTC 2011 x86_64 Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz GenuineIntel GNU/Linux Drakmail@thinkpad-x220:~$ dmesg | tail -n 10 [ 846.901574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 906.812461] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 966.728810] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1026.639676] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 1030.925574] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin At this moment I try to connect to open wifi ap: [ 1031.252403] wlan0: direct probe to 00:24:8c:55:fa:ed (try 1/3) [ 1031.451943] wlan0: direct probe to 00:24:8c:55:fa:ed (try 2/3) [ 1031.651658] wlan0: direct probe to 00:24:8c:55:fa:ed (try 3/3) [ 1031.851354] wlan0: direct probe to 00:24:8c:55:fa:ed timed out [ 1086.544960] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin My distribution: Drakmail@thinkpad-x220:~$ cat /etc/*version AgiliaLinux release 8.0.0 (Sammy) (Something between Slackware and Archlinux). Also, I saw that wifi module to often trying to load a firmware file. Any ideas what it would be?

  Read the article

• How can I restrict my mates to stop downloading?

  - by user239295

  We are sharing an internet broadband connection with 6 users at a place we live. We get 20 gb fup ( Fair usage policy) with 2 mbps speed from the ISP after the 20 gb is consumed the speed comes down to 512 kbps very difficult to browse any page. The problem is we cannot track which user/mate is downloading and ending the FUP. it is very difficult to track so is there something that we can allot per user some amount of space like 2 gb of downloading or restrict all from downloading so that we can utilize all the fup till the end of the month. We are using this connection as wifi configured. A adsl router is configured as wifi and we all using all 6 laptops. No PC. Any help would be appreciated. I apologize if i am not clear with my question.

  Read the article

• DNS issues on my iPhone

  - by mattalexx

  I'm trying to call up "https://m.google.com" on my iPhone on my home WiFi. It's saying Safari "cannot verify server identity" of m.google.com, then when I press Details, it refers to https://m.google.com as "mattserver". "mattserver" is the name of my development server, a Linux box on my home network. This stinks of DNS issues to me. Accessing the unsecure version of that URL ("http://m.google.com") gives me a blank page. What could be going on here? Is there a way to look at the logs of my router somehow?

  Read the article

• If the WiFi switched on, should it disable the ethernet? [closed]

  - by Peter Stuart

  My friend having problems with her laptop and I am trying to help her via SMS. She can't get her laptop connected to the internet via the Ethernet connection and there is no WiFi in the area. Could it be because her WiFi is switch on, she is using an acer aspire. If she manually switches it off could that allow the ethernet connecttion to work? Or is it a missing driver? The cable works fine as her someone else tried it. Thanks Peter

  Read the article

• Problems setting up VLC Sever/client streaming

  - by Ayos

  I'm trying to set up a Linux machine as the server and a Windows XP machine as the client. Both machines are connected to the same local network via a Wi-Fi router. I setup the stream with the following properties : http stream port 8080 play locally And not much else. No firewall on the windows client(Windows firewall is disabled) When I try to open network stream via the client machine(Using VLC or Windows Media Player) I get the following errors: Media Player error code : 0xC00D11B3: Encountered a network Problem. VLC Console: main warning: connection timed out access_mms error: cannot connect to 192.168.1.3:8080 main debug: no access module matching "http" could be loaded main debug: TIMER module_need() : 12625.810 ms - Total 12625.810 ms / 1 intvls (Avg 12625.809 ms) main error: open of `http://192.168.1.3:8080' failed main debug: dead input main debug: repeating item main debug: starting playback of the new playlist item main debug: resyncing on http://192.168.1.3:8080 main debug: http://192.168.1.3:8080 is at 0 main debug: creating new input thread main debug: Creating an input for 'http://192.168.1.3:8080' main debug: using timeshift granularity of 50 MiB, in path 'C:\DOCUME~1\Accer\LOCALS~1\Temp' main debug: `http://192.168.1.3:8080' gives access `http' demux `' path `192.168.1.3:8080' main debug: creating demux: access='http' demux='' location='192.168.1.3:8080' file='\\192.168.1.3:8080' main debug: looking for access_demux module: 0 candidates main debug: no access_demux module matched "http" main debug: TIMER module_need() : 0.461 ms - Total 0.461 ms / 1 intvls (Avg 0.461 ms) main debug: creating access 'http' location='192.168.1.3:8080', path='\\192.168.1.3:8080' main debug: looking for access module: 2 candidates access_http debug: http: server='192.168.1.3' port=8080 file='' main debug: net: connecting to 192.168.1.3 port 8080 qt4 debug: IM: Deleting the input main debug: TIMER input launching for 'http://192.168.1.3:8080' : 13397.979 ms - Total 13397.979 ms / 1 intvls (Avg 13397.978 ms) qt4 debug: IM: Setting an input Need Help. Thanks in advance.

  Read the article

• Public Wi-Fi and software updates

  - by coding4fun

  According to Microsoft, "Never update your software on a public Internet connection." So I have some questions. 1. What if a public Wi-Fi hotspot is the only Internet available, ever? Never update anything? 2. What happens if Windows or some other program is set to update automatically and attempts to do so while you are using a public Wi-Fi? Disable all automatic updates on all software? 3. Will VPN help to secure software updates? If so, how to go about it? Thanks.

  Read the article

• Disabling parallel network connections on workstation

  - by sumar

  Is it possible to disable prarallel network connections on workstation, when workstation is connected to corporate LAN? I want to avoid users bypassing Internet access policies by concurently connect to LAN and 3G/Hotspot. We have many developers and they have local administrator rights on workstations. Developers should be able to connect virutual networks (VMware/VirutalPC/Hyper-V/VirutalBox). Other users should be able to use only one network connection concurently.

  Read the article

• How to restrict access to other Wifi networks in range?

  - by meetpd

  Is there a way to access connecting to other wifi networks in range? I have an office and there are few wifi networks in range. Some of them are not password protected and invariably I get connected to that wifi first. I have talked to the person who owns that wifi. But he is somehow not listening about adding password to his network. So, is there a way I can block that Wifi network completely so that I do not connect to it? I have Win 7 and Mac at my office.

  Read the article

• Can't access YouTube

  - by Agentleader1

  I can not seem to connect to YouTube at all. If I connect directly to YouTube (youtube.com) I get this: And if I try to connect via video directly (youtube.com/watch?v=), I get this: Here's how this isn't a web issue: I have malware on my computer I believe. And the question here is, how do I get rid of it, or what possible issue could this be? I can verify this is not a website issue or wifi issue, I've tried to connect on another computer in my wifi, and it worked. It is the local machine issue. I've tried to get rid of malware at my best and also have tried to disable possible virus extensions. All can out as the same result: no help. Also, I am unable to find these hiding viruses. I used malware-bytes and Microsoft Security Essentials. Edit: This is OBVIOUSLY Windows. I am currently running on a laptop Windows 7 Home Premium 4gb ram 64-bit os Lifebook series manufactured by Fujitsu America, Inc. Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz nslookup youtube.com:

  Read the article

• How can I offer 2.4 ghz wi-fi in a building with strong interference?

  - by user49995

  I have a few access points on one floor of a high-rise building. They support both 2.4 ghz and 5ghz. When I used 2.4 ghz, the channel management features did not seem to work and we experienced frequent problems. When I switched to 5 ghz the problems went away. However, the 5ghz standard is much less accepted. And when clients come in, they want 2.4ghz. What can I do? How can I offer 2.4ghz wi-fi in an area with a lot of interference?

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• Can a laptop be compromised through WiFi if the machine never connects to a hotspot?

  - by MousePad

  For instance, you're laptop's wifi card is on, but you've deliberately not connected to any hot spots. Is there anyway it can be hacked while sitting there, and not connected?

  Read the article

• Video streaming and internet browsing on different bands/frequency

  - by user47207

  I have a Netgear WDNR37000 which allows clients on a 2ghz or 5ghz to access the internet and see every client and device on the network. I have a computer with two nics, one that is in the 2ghz range and the other on the 5ghz range. My specific problem is that I would like to serve my video streams (hulu, ps3mediaserver, playon) to my ps3 on the 5ghz band while internet browsing is routed to the 2ghz band. This is so that the video streams aren't affected by general internet use. While the easiest solution would be to disable internet access on the 5ghz apn, I would like to know of a solution that would not require that.

  Read the article

• how to switch played music when someone enters

  - by ymajoros

  My wife has a small shop, and she plays free licensed music. She can't legally play her own music when people outside of the family circle are present in the shop. How can I automatically switch music when someone enters? I was thinking of some bluetooth door detector and some custom software, but can't seem to find either. I'm a software architect/dev and can write it if necessary, but I'd prefer to use some existing solution. Any ideas on good hardware and software for this?

  Read the article

• Mac OS X change IP configuration automatically by location (by Wifi network)?

  - by Seppo Sade

  Can Mac OS X be setup to automatically configure its Airport interface with a static IP address when connected to a Wifi network with a certain name, and on all other Wifi networks use DHCP? Currently I'm using the "Locations" feature of the "Network" section in System Preferences to manually switch between two IP address setups. I have a "my static IP" setup, and a default "DHCP" setup. However this requires entering System Preferences to change the Location drop-down each time when switching locations. Can this be automated? Preferably this would be done without third-party software.

  Read the article

• Preventing apps to access info from wifi device?

  - by heaosax

  Browsers like Chrome and Firefox can use my wifi device to get information about the surrounded APs and pin point my physical location using Google Location Services, I know these browser always ask for permissions to do this, and that these features can also be "turned off". But I was wondering if there's a better way to prevent ANY application to access this information from my wifi device. I don't like anyone on the internet knowing where I live, and I am worried some software could do the same as these browsers but without asking for permissions. I am using Ubuntu 10.04.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >