Search Results

Search found 2796 results on 112 pages for 'bounce rate'.

Page 109/112 | < Previous Page | 105 106 107 108 109 110 111 112  | Next Page >

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• asp.net C# Webcam api error

  - by Eyla

  Greeting, I'm tring to use webcam api with asp.net and C#. I included all the library and reverince I needed for that. the original code I'm use was for windows application and I'm trying to convert it to asp.net web application. I have start capturing button when I click it, it should start capturing but it gives me an error. the error at this line: hHwnd = capCreateCaptureWindowA(iDevice.ToString(), (WS_VISIBLE | WS_CHILD), 0, 0, 640, 480, picCapture.Handle.ToInt32(), 0); and the error message is: Error 1 'System.Web.UI.WebControls.Image' does not contain a definition for 'Handle' and no extension method 'Handle' accepting a first argument of type 'System.Web.UI.WebControls.Image' could be found (are you missing a using directive or an assembly reference?) C:\Users\Ali\Documents\Visual Studio 2008\Projects\Conference\Conference\Conference1.aspx.cs 63 117 Conference Please advice!! ................................................ here is the complete code ........................................... using System; using System.Collections; using System.Drawing; using System.ComponentModel; using System.Windows.Forms; using System.Configuration; using System.Data; using System.Linq; using System.Web; using System.Web.Security; using System.Web.UI; using System.Web.UI.HtmlControls; using System.Web.UI.WebControls; using System.Web.UI.WebControls.WebParts; using System.Xml.Linq; using System.Runtime.InteropServices; using System.Drawing.Imaging; using System.Net; using System.Net.Sockets; using System.Threading; using System.IO; namespace Conference { public partial class Conference1 : System.Web.UI.Page { #region WebCam API const short WM_CAP = 1024; const int WM_CAP_DRIVER_CONNECT = WM_CAP + 10; const int WM_CAP_DRIVER_DISCONNECT = WM_CAP + 11; const int WM_CAP_EDIT_COPY = WM_CAP + 30; const int WM_CAP_SET_PREVIEW = WM_CAP + 50; const int WM_CAP_SET_PREVIEWRATE = WM_CAP + 52; const int WM_CAP_SET_SCALE = WM_CAP + 53; const int WS_CHILD = 1073741824; const int WS_VISIBLE = 268435456; const short SWP_NOMOVE = 2; const short SWP_NOSIZE = 1; const short SWP_NOZORDER = 4; const short HWND_BOTTOM = 1; int iDevice = 0; int hHwnd; [System.Runtime.InteropServices.DllImport("user32", EntryPoint = "SendMessageA")] static extern int SendMessage(int hwnd, int wMsg, int wParam, [MarshalAs(UnmanagedType.AsAny)] object lParam); [System.Runtime.InteropServices.DllImport("user32", EntryPoint = "SetWindowPos")] static extern int SetWindowPos(int hwnd, int hWndInsertAfter, int x, int y, int cx, int cy, int wFlags); [System.Runtime.InteropServices.DllImport("user32")] static extern bool DestroyWindow(int hndw); [System.Runtime.InteropServices.DllImport("avicap32.dll")] static extern int capCreateCaptureWindowA(string lpszWindowName, int dwStyle, int x, int y, int nWidth, short nHeight, int hWndParent, int nID); [System.Runtime.InteropServices.DllImport("avicap32.dll")] static extern bool capGetDriverDescriptionA(short wDriver, string lpszName, int cbName, string lpszVer, int cbVer); private void OpenPreviewWindow() { int iHeight = 320; int iWidth = 200; // // Open Preview window in picturebox // hHwnd = capCreateCaptureWindowA(iDevice.ToString(), (WS_VISIBLE | WS_CHILD), 0, 0, 640, 480, picCapture.Handle.ToInt32(), 0); // // Connect to device // if (SendMessage(hHwnd, WM_CAP_DRIVER_CONNECT, iDevice, 0) == 1) { // // Set the preview scale // SendMessage(hHwnd, WM_CAP_SET_SCALE, 1, 0); // // Set the preview rate in milliseconds // SendMessage(hHwnd, WM_CAP_SET_PREVIEWRATE, 66, 0); // // Start previewing the image from the camera // SendMessage(hHwnd, WM_CAP_SET_PREVIEW, 1, 0); // // Resize window to fit in picturebox // SetWindowPos(hHwnd, HWND_BOTTOM, 0, 0, iWidth, iHeight, (SWP_NOMOVE | SWP_NOZORDER)); } else { // // Error connecting to device close window // DestroyWindow(hHwnd); } } private void ClosePreviewWindow() { // // Disconnect from device // SendMessage(hHwnd, WM_CAP_DRIVER_DISCONNECT, iDevice, 0); // // close window // DestroyWindow(hHwnd); } #endregion protected void Page_Load(object sender, EventArgs e) { } protected void btnStart_Click(object sender, EventArgs e) { int iDevice = int.Parse(device_number_textBox.Text); OpenPreviewWindow(); } } }

  Read the article

• MySQL is running VERY slow

  - by user1032531

  I have two servers: a VPS and a laptop. I recently re-built both of them, and MySQL is running about 20 times slower on the laptop. Both servers used to run CentOS 5.8 and I think MySQL 5.1, and the laptop used to do great so I do not think it is the hardware. For the VPS, my provider installed CentOS 6.4, and then I installed MySQL 5.1.69 using yum with the CentOS repo. For the laptop, I installed CentOS 6.4 basic server and then installed MySQL 5.1.69 using yum with the CentOS repo. my.cnf for both servers are identical, and I have shown below. For both servers, I've also included below the output from SHOW VARIABLES; as well as output from sysbench, file system information, and cpu information. I have tried adding skip-name-resolve, but it didn't help. The matrix below shows the SHOW VARIABLES output from both servers which is different. Again, MySQL was installed the same way, so I do not know why it is different, but it is and I think this might be why the laptop is executing MySQL so slowly. Why is the laptop running MySQL slowly, and how do I fix it? Differences between SHOW VARIABLES on both servers +---------------------------+-----------------------+-------------------------+ | Variable | Value-VPS | Value-Laptop | +---------------------------+-----------------------+-------------------------+ | hostname | vps.site1.com | laptop.site2.com | | max_binlog_cache_size | 4294963200 | 18446744073709500000 | | max_seeks_for_key | 4294967295 | 18446744073709500000 | | max_write_lock_count | 4294967295 | 18446744073709500000 | | myisam_max_sort_file_size | 2146435072 | 9223372036853720000 | | myisam_mmap_size | 4294967295 | 18446744073709500000 | | plugin_dir | /usr/lib/mysql/plugin | /usr/lib64/mysql/plugin | | pseudo_thread_id | 7568 | 2 | | system_time_zone | EST | PDT | | thread_stack | 196608 | 262144 | | timestamp | 1372252112 | 1372252046 | | version_compile_machine | i386 | x86_64 | +---------------------------+-----------------------+-------------------------+ my.cnf for both servers [root@server1 ~]# cat /etc/my.cnf [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid innodb_strict_mode=on sql_mode=TRADITIONAL # sql_mode=STRICT_TRANS_TABLES,NO_ZERO_DATE,NO_ZERO_IN_DATE character-set-server=utf8 collation-server=utf8_general_ci log=/var/log/mysqld_all.log [root@server1 ~]# VPS SHOW VARIABLES Info Same as Laptop shown below but changes per above matrix (removed to allow me to be under the 30000 characters as required by ServerFault) Laptop SHOW VARIABLES Info auto_increment_increment 1 auto_increment_offset 1 autocommit ON automatic_sp_privileges ON back_log 50 basedir /usr/ big_tables OFF binlog_cache_size 32768 binlog_direct_non_transactional_updates OFF binlog_format STATEMENT bulk_insert_buffer_size 8388608 character_set_client utf8 character_set_connection utf8 character_set_database latin1 character_set_filesystem binary character_set_results utf8 character_set_server latin1 character_set_system utf8 character_sets_dir /usr/share/mysql/charsets/ collation_connection utf8_general_ci collation_database latin1_swedish_ci collation_server latin1_swedish_ci completion_type 0 concurrent_insert 1 connect_timeout 10 datadir /var/lib/mysql/ date_format %Y-%m-%d datetime_format %Y-%m-%d %H:%i:%s default_week_format 0 delay_key_write ON delayed_insert_limit 100 delayed_insert_timeout 300 delayed_queue_size 1000 div_precision_increment 4 engine_condition_pushdown ON error_count 0 event_scheduler OFF expire_logs_days 0 flush OFF flush_time 0 foreign_key_checks ON ft_boolean_syntax + -><()~*:""&| ft_max_word_len 84 ft_min_word_len 4 ft_query_expansion_limit 20 ft_stopword_file (built-in) general_log OFF general_log_file /var/run/mysqld/mysqld.log group_concat_max_len 1024 have_community_features YES have_compress YES have_crypt YES have_csv YES have_dynamic_loading YES have_geometry YES have_innodb YES have_ndbcluster NO have_openssl DISABLED have_partitioning YES have_query_cache YES have_rtree_keys YES have_ssl DISABLED have_symlink DISABLED hostname server1.site2.com identity 0 ignore_builtin_innodb OFF init_connect init_file init_slave innodb_adaptive_hash_index ON innodb_additional_mem_pool_size 1048576 innodb_autoextend_increment 8 innodb_autoinc_lock_mode 1 innodb_buffer_pool_size 8388608 innodb_checksums ON innodb_commit_concurrency 0 innodb_concurrency_tickets 500 innodb_data_file_path ibdata1:10M:autoextend innodb_data_home_dir innodb_doublewrite ON innodb_fast_shutdown 1 innodb_file_io_threads 4 innodb_file_per_table OFF innodb_flush_log_at_trx_commit 1 innodb_flush_method innodb_force_recovery 0 innodb_lock_wait_timeout 50 innodb_locks_unsafe_for_binlog OFF innodb_log_buffer_size 1048576 innodb_log_file_size 5242880 innodb_log_files_in_group 2 innodb_log_group_home_dir ./ innodb_max_dirty_pages_pct 90 innodb_max_purge_lag 0 innodb_mirrored_log_groups 1 innodb_open_files 300 innodb_rollback_on_timeout OFF innodb_stats_method nulls_equal innodb_stats_on_metadata ON innodb_support_xa ON innodb_sync_spin_loops 20 innodb_table_locks ON innodb_thread_concurrency 8 innodb_thread_sleep_delay 10000 innodb_use_legacy_cardinality_algorithm ON insert_id 0 interactive_timeout 28800 join_buffer_size 131072 keep_files_on_create OFF key_buffer_size 8384512 key_cache_age_threshold 300 key_cache_block_size 1024 key_cache_division_limit 100 language /usr/share/mysql/english/ large_files_support ON large_page_size 0 large_pages OFF last_insert_id 0 lc_time_names en_US license GPL local_infile ON locked_in_memory OFF log OFF log_bin OFF log_bin_trust_function_creators OFF log_bin_trust_routine_creators OFF log_error /var/log/mysqld.log log_output FILE log_queries_not_using_indexes OFF log_slave_updates OFF log_slow_queries OFF log_warnings 1 long_query_time 10.000000 low_priority_updates OFF lower_case_file_system OFF lower_case_table_names 0 max_allowed_packet 1048576 max_binlog_cache_size 18446744073709547520 max_binlog_size 1073741824 max_connect_errors 10 max_connections 151 max_delayed_threads 20 max_error_count 64 max_heap_table_size 16777216 max_insert_delayed_threads 20 max_join_size 18446744073709551615 max_length_for_sort_data 1024 max_long_data_size 1048576 max_prepared_stmt_count 16382 max_relay_log_size 0 max_seeks_for_key 18446744073709551615 max_sort_length 1024 max_sp_recursion_depth 0 max_tmp_tables 32 max_user_connections 0 max_write_lock_count 18446744073709551615 min_examined_row_limit 0 multi_range_count 256 myisam_data_pointer_size 6 myisam_max_sort_file_size 9223372036853727232 myisam_mmap_size 18446744073709551615 myisam_recover_options OFF myisam_repair_threads 1 myisam_sort_buffer_size 8388608 myisam_stats_method nulls_unequal myisam_use_mmap OFF net_buffer_length 16384 net_read_timeout 30 net_retry_count 10 net_write_timeout 60 new OFF old OFF old_alter_table OFF old_passwords OFF open_files_limit 1024 optimizer_prune_level 1 optimizer_search_depth 62 optimizer_switch index_merge=on,index_merge_union=on,index_merge_sort_union=on,index_merge_intersection=on pid_file /var/run/mysqld/mysqld.pid plugin_dir /usr/lib64/mysql/plugin port 3306 preload_buffer_size 32768 profiling OFF profiling_history_size 15 protocol_version 10 pseudo_thread_id 3 query_alloc_block_size 8192 query_cache_limit 1048576 query_cache_min_res_unit 4096 query_cache_size 0 query_cache_type ON query_cache_wlock_invalidate OFF query_prealloc_size 8192 rand_seed1 rand_seed2 range_alloc_block_size 4096 read_buffer_size 131072 read_only OFF read_rnd_buffer_size 262144 relay_log relay_log_index relay_log_info_file relay-log.info relay_log_purge ON relay_log_space_limit 0 report_host report_password report_port 3306 report_user rpl_recovery_rank 0 secure_auth OFF secure_file_priv server_id 0 skip_external_locking ON skip_name_resolve OFF skip_networking OFF skip_show_database OFF slave_compressed_protocol OFF slave_exec_mode STRICT slave_load_tmpdir /tmp slave_max_allowed_packet 1073741824 slave_net_timeout 3600 slave_skip_errors OFF slave_transaction_retries 10 slow_launch_time 2 slow_query_log OFF slow_query_log_file /var/run/mysqld/mysqld-slow.log socket /var/lib/mysql/mysql.sock sort_buffer_size 2097144 sql_auto_is_null ON sql_big_selects ON sql_big_tables OFF sql_buffer_result OFF sql_log_bin ON sql_log_off OFF sql_log_update ON sql_low_priority_updates OFF sql_max_join_size 18446744073709551615 sql_mode sql_notes ON sql_quote_show_create ON sql_safe_updates OFF sql_select_limit 18446744073709551615 sql_slave_skip_counter sql_warnings OFF ssl_ca ssl_capath ssl_cert ssl_cipher ssl_key storage_engine MyISAM sync_binlog 0 sync_frm ON system_time_zone PDT table_definition_cache 256 table_lock_wait_timeout 50 table_open_cache 64 table_type MyISAM thread_cache_size 0 thread_handling one-thread-per-connection thread_stack 262144 time_format %H:%i:%s time_zone SYSTEM timed_mutexes OFF timestamp 1372254399 tmp_table_size 16777216 tmpdir /tmp transaction_alloc_block_size 8192 transaction_prealloc_size 4096 tx_isolation REPEATABLE-READ unique_checks ON updatable_views_with_limit YES version 5.1.69 version_comment Source distribution version_compile_machine x86_64 version_compile_os redhat-linux-gnu wait_timeout 28800 warning_count 0 VPS Sysbench Info [root@vps ~]# cat sysbench.txt sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 8 Doing OLTP test. Running mixed OLTP test Doing read-only test Using Special distribution (12 iterations, 1 pct of values are returned in 75 pct cases) Using "BEGIN" for starting transactions Using auto_inc on the id column Threads started! Time limit exceeded, exiting... (last message repeated 7 times) Done. OLTP test statistics: queries performed: read: 1449966 write: 0 other: 207138 total: 1657104 transactions: 103569 (1726.01 per sec.) deadlocks: 0 (0.00 per sec.) read/write requests: 1449966 (24164.08 per sec.) other operations: 207138 (3452.01 per sec.) Test execution summary: total time: 60.0050s total number of events: 103569 total time taken by event execution: 479.1544 per-request statistics: min: 1.98ms avg: 4.63ms max: 330.73ms approx. 95 percentile: 8.26ms Threads fairness: events (avg/stddev): 12946.1250/381.09 execution time (avg/stddev): 59.8943/0.00 [root@vps ~]# Laptop Sysbench Info [root@server1 ~]# cat sysbench.txt sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 8 Doing OLTP test. Running mixed OLTP test Doing read-only test Using Special distribution (12 iterations, 1 pct of values are returned in 75 pct cases) Using "BEGIN" for starting transactions Using auto_inc on the id column Threads started! Time limit exceeded, exiting... (last message repeated 7 times) Done. OLTP test statistics: queries performed: read: 634718 write: 0 other: 90674 total: 725392 transactions: 45337 (755.56 per sec.) deadlocks: 0 (0.00 per sec.) read/write requests: 634718 (10577.78 per sec.) other operations: 90674 (1511.11 per sec.) Test execution summary: total time: 60.0048s total number of events: 45337 total time taken by event execution: 479.4912 per-request statistics: min: 2.04ms avg: 10.58ms max: 85.56ms approx. 95 percentile: 19.70ms Threads fairness: events (avg/stddev): 5667.1250/42.18 execution time (avg/stddev): 59.9364/0.00 [root@server1 ~]# VPS File Info [root@vps ~]# df -T Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/simfs simfs 20971520 16187440 4784080 78% / none tmpfs 6224432 4 6224428 1% /dev none tmpfs 6224432 0 6224432 0% /dev/shm [root@vps ~]# Laptop File Info [root@server1 ~]# df -T Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_server1-lv_root ext4 72383800 4243964 64462860 7% / tmpfs tmpfs 956352 0 956352 0% /dev/shm /dev/sdb1 ext4 495844 60948 409296 13% /boot [root@server1 ~]# VPS CPU Info Removed to stay under the 30000 character limit required by ServerFault Laptop CPU Info [root@server1 ~]# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz stepping : 13 cpu MHz : 800.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 3591.39 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz stepping : 13 cpu MHz : 800.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 3591.39 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: [root@server1 ~]# EDIT New Info requested by shakalandy [root@localhost ~]# cat /proc/meminfo MemTotal: 2044804 kB MemFree: 761464 kB Buffers: 68868 kB Cached: 369708 kB SwapCached: 0 kB Active: 881080 kB Inactive: 246016 kB Active(anon): 688312 kB Inactive(anon): 4416 kB Active(file): 192768 kB Inactive(file): 241600 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 4095992 kB SwapFree: 4095992 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 688428 kB Mapped: 65156 kB Shmem: 4216 kB Slab: 92428 kB SReclaimable: 31260 kB SUnreclaim: 61168 kB KernelStack: 2392 kB PageTables: 28356 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 5118392 kB Committed_AS: 1530212 kB VmallocTotal: 34359738367 kB VmallocUsed: 343604 kB VmallocChunk: 34359372920 kB HardwareCorrupted: 0 kB AnonHugePages: 520192 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 8556 kB DirectMap2M: 2078720 kB [root@localhost ~]# ps aux | grep mysql root 2227 0.0 0.0 108332 1504 ? S 07:36 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/localhost.badobe.com.pid mysql 2319 0.1 24.5 1470068 501360 ? Sl 07:36 0:57 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib64/mysql/plugin --user=mysql --log-error=/var/lib/mysql/localhost.badobe.com.err --pid-file=/var/lib/mysql/localhost.badobe.com.pid root 3579 0.0 0.1 201840 3028 pts/0 S+ 07:40 0:00 mysql -u root -p root 13887 0.0 0.1 201840 3036 pts/3 S+ 18:08 0:00 mysql -uroot -px xxxxxxxxxx root 14449 0.0 0.0 103248 840 pts/2 S+ 18:16 0:00 grep mysql [root@localhost ~]# ps aux | grep mysql root 2227 0.0 0.0 108332 1504 ? S 07:36 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/localhost.badobe.com.pid mysql 2319 0.1 24.5 1470068 501356 ? Sl 07:36 0:57 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib64/mysql/plugin --user=mysql --log-error=/var/lib/mysql/localhost.badobe.com.err --pid-file=/var/lib/mysql/localhost.badobe.com.pid root 3579 0.0 0.1 201840 3028 pts/0 S+ 07:40 0:00 mysql -u root -p root 13887 0.0 0.1 201840 3048 pts/3 S+ 18:08 0:00 mysql -uroot -px xxxxxxxxxx root 14470 0.0 0.0 103248 840 pts/2 S+ 18:16 0:00 grep mysql [root@localhost ~]# vmstat 1 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 742172 76376 371064 0 0 6 6 78 202 2 1 97 1 0 0 0 0 742164 76380 371060 0 0 0 16 191 467 2 1 93 5 0 0 0 0 742164 76380 371064 0 0 0 0 148 388 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 159 418 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 145 380 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 166 429 2 1 97 0 0 1 0 0 742164 76380 371064 0 0 0 0 148 373 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 149 382 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 168 408 2 0 97 0 0 0 0 0 742164 76380 371064 0 0 0 0 165 394 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 159 354 2 1 98 0 0 0 0 0 742164 76388 371060 0 0 0 16 180 447 2 0 91 6 0 0 0 0 742164 76388 371064 0 0 0 0 143 344 2 1 98 0 0 0 1 0 742784 76416 370044 0 0 28 580 360 678 3 1 74 23 0 1 0 0 744768 76496 367772 0 0 40 1036 437 865 3 1 53 43 0 0 1 0 747248 76596 365412 0 0 48 1224 561 923 3 2 53 43 0 0 1 0 749232 76696 363092 0 0 32 1132 512 883 3 2 52 44 0 0 1 0 751340 76772 361020 0 0 32 1008 472 872 2 1 52 45 0 0 1 0 753448 76840 358540 0 0 36 1088 512 860 2 1 51 46 0 0 1 0 755060 76936 357636 0 0 28 1012 481 922 2 2 52 45 0 0 1 0 755060 77064 357988 0 0 12 896 444 902 2 1 53 45 0 0 1 0 754688 77148 358448 0 0 16 1096 506 1007 1 1 56 42 0 0 2 0 754192 77268 358932 0 0 12 1060 481 957 1 2 53 44 0 0 1 0 753696 77380 359392 0 0 12 1052 512 1025 2 1 55 42 0 0 1 0 751028 77480 359828 0 0 8 984 423 909 2 2 52 45 0 0 1 0 750524 77620 360200 0 0 8 788 367 869 1 2 54 44 0 0 1 0 749904 77700 360664 0 0 8 928 439 924 2 2 55 43 0 0 1 0 749408 77796 361084 0 0 12 976 468 967 1 1 56 43 0 0 1 0 748788 77896 361464 0 0 12 992 453 944 1 2 54 43 0 1 1 0 748416 77992 361996 0 0 12 784 392 868 2 1 52 46 0 0 1 0 747920 78092 362336 0 0 4 896 382 874 1 1 52 46 0 0 1 0 745252 78172 362780 0 0 12 1040 444 923 1 1 56 42 0 0 1 0 744764 78288 363220 0 0 8 1024 448 934 2 1 55 43 0 0 1 0 744144 78408 363668 0 0 8 1000 461 982 2 1 53 44 0 0 1 0 743648 78488 364148 0 0 8 872 443 888 2 1 54 43 0 0 1 0 743152 78548 364468 0 0 16 1020 511 995 2 1 55 43 0 0 1 0 742656 78632 365024 0 0 12 928 431 913 1 2 53 44 0 0 1 0 742160 78728 365468 0 0 12 996 470 955 2 2 54 44 0 1 1 0 739492 78840 365896 0 0 8 988 447 939 1 2 52 46 0 0 1 0 738872 78996 366352 0 0 12 972 442 928 1 1 55 44 0 1 1 0 738244 79148 366812 0 0 8 948 549 1126 2 2 54 43 0 0 1 0 737624 79312 367188 0 0 12 996 456 953 2 2 54 43 0 0 1 0 736880 79456 367660 0 0 12 960 444 918 1 1 53 46 0 0 1 0 736260 79584 368124 0 0 8 884 414 921 1 1 54 44 0 0 1 0 735648 79716 368488 0 0 12 976 450 955 2 1 56 41 0 0 1 0 733104 79840 368988 0 0 12 932 453 918 1 2 55 43 0 0 1 0 732608 79996 369356 0 0 16 916 444 889 1 2 54 43 0 1 1 0 731476 80128 369800 0 0 16 852 514 978 2 2 54 43 0 0 1 0 731244 80252 370200 0 0 8 904 398 870 2 1 55 43 0 1 1 0 730624 80384 370612 0 0 12 1032 447 977 1 2 57 41 0 0 1 0 730004 80524 371096 0 0 12 984 469 941 2 2 52 45 0 0 1 0 729508 80636 371544 0 0 12 928 438 922 2 1 52 46 0 0 1 0 728888 80756 371948 0 0 16 972 439 943 2 1 55 43 0 0 1 0 726468 80900 372272 0 0 8 960 545 1024 2 1 54 43 0 1 1 0 726344 81024 372272 0 0 8 464 490 1057 1 2 53 44 0 0 1 0 726096 81148 372276 0 0 4 328 441 1063 2 1 53 45 0 1 1 0 726096 81256 372292 0 0 0 296 387 975 1 1 53 45 0 0 1 0 725848 81380 372284 0 0 4 332 425 1034 2 1 54 44 0 1 1 0 725848 81496 372300 0 0 4 308 386 992 2 1 54 43 0 0 1 0 725600 81616 372296 0 0 4 328 404 1060 1 1 54 44 0 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 1 0 725600 81732 372296 0 0 4 328 439 1011 1 1 53 44 0 0 1 0 725476 81848 372308 0 0 0 316 441 1023 2 2 52 46 0 1 1 0 725352 81972 372300 0 0 4 344 451 1021 1 1 55 43 0 2 1 0 725228 82088 372320 0 0 0 328 427 1058 1 1 54 44 0 1 1 0 724980 82220 372300 0 0 4 336 419 999 2 1 54 44 0 1 1 0 724980 82328 372320 0 0 4 320 430 1019 1 1 54 44 0 1 1 0 724732 82436 372328 0 0 0 388 363 942 2 1 54 44 0 1 1 0 724608 82560 372312 0 0 4 308 419 993 1 2 54 44 0 1 0 0 724360 82684 372320 0 0 0 304 421 1028 2 1 55 42 0 1 0 0 724360 82684 372388 0 0 0 0 158 416 2 1 98 0 0 1 1 0 724236 82720 372360 0 0 0 6464 243 855 3 2 84 12 0 1 0 0 724112 82748 372360 0 0 0 5356 266 895 3 1 84 12 0 2 1 0 724112 82764 372380 0 0 0 3052 221 511 2 2 93 4 0 1 0 0 724112 82796 372372 0 0 0 4548 325 1067 2 2 81 16 0 1 0 0 724112 82816 372368 0 0 0 3240 259 829 3 1 90 6 0 1 0 0 724112 82836 372380 0 0 0 3260 309 822 3 2 88 8 0 1 1 0 724112 82876 372364 0 0 0 4680 326 978 3 1 77 19 0 1 0 0 724112 82884 372380 0 0 0 512 207 508 2 1 95 2 0 1 0 0 724112 82884 372388 0 0 0 0 138 361 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 158 397 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 146 395 2 1 98 0 0 2 0 0 724112 82884 372388 0 0 0 0 160 395 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 163 382 1 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 176 422 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 134 351 2 1 98 0 0 0 0 0 724112 82884 372388 0 0 0 0 190 429 2 1 97 0 0 0 0 0 724104 82884 372392 0 0 0 0 139 358 2 1 98 0 0 0 0 0 724848 82884 372392 0 0 0 4 211 432 2 1 97 0 0 1 0 0 724980 82884 372392 0 0 0 0 166 370 2 1 98 0 0 0 0 0 724980 82884 372392 0 0 0 0 164 397 2 1 98 0 0 ^C [root@localhost ~]#

  Read the article

• Does anyone really understand how HFSC scheduling in Linux/BSD works?

  - by Mecki

  I read the original SIGCOMM '97 PostScript paper about HFSC, it is very technically, but I understand the basic concept. Instead of giving a linear service curve (as with pretty much every other scheduling algorithm), you can specify a convex or concave service curve and thus it is possible to decouple bandwidth and delay. However, even though this paper mentions to kind of scheduling algorithms being used (real-time and link-share), it always only mentions ONE curve per scheduling class (the decoupling is done by specifying this curve, only one curve is needed for that). Now HFSC has been implemented for BSD (OpenBSD, FreeBSD, etc.) using the ALTQ scheduling framework and it has been implemented Linux using the TC scheduling framework (part of iproute2). Both implementations added two additional service curves, that were NOT in the original paper! A real-time service curve and an upper-limit service curve. Again, please note that the original paper mentions two scheduling algorithms (real-time and link-share), but in that paper both work with one single service curve. There never have been two independent service curves for either one as you currently find in BSD and Linux. Even worse, some version of ALTQ seems to add an additional queue priority to HSFC (there is no such thing as priority in the original paper either). I found several BSD HowTo's mentioning this priority setting (even though the man page of the latest ALTQ release knows no such parameter for HSFC, so officially it does not even exist). This all makes the HFSC scheduling even more complex than the algorithm described in the original paper and there are tons of tutorials on the Internet that often contradict each other, one claiming the opposite of the other one. This is probably the main reason why nobody really seems to understand how HFSC scheduling really works. Before I can ask my questions, we need a sample setup of some kind. I'll use a very simple one as seen in the image below: Here are some questions I cannot answer because the tutorials contradict each other: What for do I need a real-time curve at all? Assuming A1, A2, B1, B2 are all 128 kbit/s link-share (no real-time curve for either one), then each of those will get 128 kbit/s if the root has 512 kbit/s to distribute (and A and B are both 256 kbit/s of course), right? Why would I additionally give A1 and B1 a real-time curve with 128 kbit/s? What would this be good for? To give those two a higher priority? According to original paper I can give them a higher priority by using a curve, that's what HFSC is all about after all. By giving both classes a curve of [256kbit/s 20ms 128kbit/s] both have twice the priority than A2 and B2 automatically (still only getting 128 kbit/s on average) Does the real-time bandwidth count towards the link-share bandwidth? E.g. if A1 and B1 both only have 64kbit/s real-time and 64kbit/s link-share bandwidth, does that mean once they are served 64kbit/s via real-time, their link-share requirement is satisfied as well (they might get excess bandwidth, but lets ignore that for a second) or does that mean they get another 64 kbit/s via link-share? So does each class has a bandwidth "requirement" of real-time plus link-share? Or does a class only have a higher requirement than the real-time curve if the link-share curve is higher than the real-time curve (current link-share requirement equals specified link-share requirement minus real-time bandwidth already provided to this class)? Is upper limit curve applied to real-time as well, only to link-share, or maybe to both? Some tutorials say one way, some say the other way. Some even claim upper-limit is the maximum for real-time bandwidth + link-share bandwidth? What is the truth? Assuming A2 and B2 are both 128 kbit/s, does it make any difference if A1 and B1 are 128 kbit/s link-share only, or 64 kbit/s real-time and 128 kbit/s link-share, and if so, what difference? If I use the seperate real-time curve to increase priorities of classes, why would I need "curves" at all? Why is not real-time a flat value and link-share also a flat value? Why are both curves? The need for curves is clear in the original paper, because there is only one attribute of that kind per class. But now, having three attributes (real-time, link-share, and upper-limit) what for do I still need curves on each one? Why would I want the curves shape (not average bandwidth, but their slopes) to be different for real-time and link-share traffic? According to the little documentation available, real-time curve values are totally ignored for inner classes (class A and B), they are only applied to leaf classes (A1, A2, B1, B2). If that is true, why does the ALTQ HFSC sample configuration (search for 3.3 Sample configuration) set real-time curves on inner classes and claims that those set the guaranteed rate of those inner classes? Isn't that completely pointless? (note: pshare sets the link-share curve in ALTQ and grate the real-time curve; you can see this in the paragraph above the sample configuration). Some tutorials say the sum of all real-time curves may not be higher than 80% of the line speed, others say it must not be higher than 70% of the line speed. Which one is right or are they maybe both wrong? One tutorial said you shall forget all the theory. No matter how things really work (schedulers and bandwidth distribution), imagine the three curves according to the following "simplified mind model": real-time is the guaranteed bandwidth that this class will always get. link-share is the bandwidth that this class wants to become fully satisfied, but satisfaction cannot be guaranteed. In case there is excess bandwidth, the class might even get offered more bandwidth than necessary to become satisfied, but it may never use more than upper-limit says. For all this to work, the sum of all real-time bandwidths may not be above xx% of the line speed (see question above, the percentage varies). Question: Is this more or less accurate or a total misunderstanding of HSFC? And if assumption above is really accurate, where is prioritization in that model? E.g. every class might have a real-time bandwidth (guaranteed), a link-share bandwidth (not guaranteed) and an maybe an upper-limit, but still some classes have higher priority needs than other classes. In that case I must still prioritize somehow, even among real-time traffic of those classes. Would I prioritize by the slope of the curves? And if so, which curve? The real-time curve? The link-share curve? The upper-limit curve? All of them? Would I give all of them the same slope or each a different one and how to find out the right slope? I still haven't lost hope that there exists at least a hand full of people in this world that really understood HFSC and are able to answer all these questions accurately. And doing so without contradicting each other in the answers would be really nice ;-)

  Read the article

• Webcam api error when accessed from ASP.NET Server-side code

  - by Eyla

  I'm tring to use webcam api with asp.net and C#. I included all the library and references I needed for that. the original code I'm use was for windows application and I'm trying to convert it to asp.net web application. I have start capturing button when I click it, it should start capturing but it gives me an error. the error at this line: hHwnd = capCreateCaptureWindowA(iDevice.ToString(), (WS_VISIBLE | WS_CHILD), 0, 0, 640, 480, picCapture.Handle.ToInt32(), 0); and the error message is: Error 1 'System.Web.UI.WebControls.Image' does not contain a definition for 'Handle' and no extension method 'Handle' accepting a first argument of type 'System.Web.UI.WebControls.Image' could be found (are you missing a using directive or an assembly reference?) C:\Users\Ali\Documents\Visual Studio 2008\Projects\Conference\Conference\Conference1.aspx.cs 63 117 Conference Please advice!! ................................................ here is the complete code ........................................... using System; using System.Collections; using System.Drawing; using System.ComponentModel; using System.Windows.Forms; using System.Configuration; using System.Data; using System.Linq; using System.Web; using System.Web.Security; using System.Web.UI; using System.Web.UI.HtmlControls; using System.Web.UI.WebControls; using System.Web.UI.WebControls.WebParts; using System.Xml.Linq; using System.Runtime.InteropServices; using System.Drawing.Imaging; using System.Net; using System.Net.Sockets; using System.Threading; using System.IO; namespace Conference { public partial class Conference1 : System.Web.UI.Page { #region WebCam API const short WM_CAP = 1024; const int WM_CAP_DRIVER_CONNECT = WM_CAP + 10; const int WM_CAP_DRIVER_DISCONNECT = WM_CAP + 11; const int WM_CAP_EDIT_COPY = WM_CAP + 30; const int WM_CAP_SET_PREVIEW = WM_CAP + 50; const int WM_CAP_SET_PREVIEWRATE = WM_CAP + 52; const int WM_CAP_SET_SCALE = WM_CAP + 53; const int WS_CHILD = 1073741824; const int WS_VISIBLE = 268435456; const short SWP_NOMOVE = 2; const short SWP_NOSIZE = 1; const short SWP_NOZORDER = 4; const short HWND_BOTTOM = 1; int iDevice = 0; int hHwnd; [System.Runtime.InteropServices.DllImport("user32", EntryPoint = "SendMessageA")] static extern int SendMessage(int hwnd, int wMsg, int wParam, [MarshalAs(UnmanagedType.AsAny)] object lParam); [System.Runtime.InteropServices.DllImport("user32", EntryPoint = "SetWindowPos")] static extern int SetWindowPos(int hwnd, int hWndInsertAfter, int x, int y, int cx, int cy, int wFlags); [System.Runtime.InteropServices.DllImport("user32")] static extern bool DestroyWindow(int hndw); [System.Runtime.InteropServices.DllImport("avicap32.dll")] static extern int capCreateCaptureWindowA(string lpszWindowName, int dwStyle, int x, int y, int nWidth, short nHeight, int hWndParent, int nID); [System.Runtime.InteropServices.DllImport("avicap32.dll")] static extern bool capGetDriverDescriptionA(short wDriver, string lpszName, int cbName, string lpszVer, int cbVer); private void OpenPreviewWindow() { int iHeight = 320; int iWidth = 200; // // Open Preview window in picturebox // hHwnd = capCreateCaptureWindowA(iDevice.ToString(), (WS_VISIBLE | WS_CHILD), 0, 0, 640, 480, picCapture.Handle.ToInt32(), 0); // // Connect to device // if (SendMessage(hHwnd, WM_CAP_DRIVER_CONNECT, iDevice, 0) == 1) { // // Set the preview scale // SendMessage(hHwnd, WM_CAP_SET_SCALE, 1, 0); // // Set the preview rate in milliseconds // SendMessage(hHwnd, WM_CAP_SET_PREVIEWRATE, 66, 0); // // Start previewing the image from the camera // SendMessage(hHwnd, WM_CAP_SET_PREVIEW, 1, 0); // // Resize window to fit in picturebox // SetWindowPos(hHwnd, HWND_BOTTOM, 0, 0, iWidth, iHeight, (SWP_NOMOVE | SWP_NOZORDER)); } else { // // Error connecting to device close window // DestroyWindow(hHwnd); } } private void ClosePreviewWindow() { // // Disconnect from device // SendMessage(hHwnd, WM_CAP_DRIVER_DISCONNECT, iDevice, 0); // // close window // DestroyWindow(hHwnd); } #endregion protected void Page_Load(object sender, EventArgs e) { } protected void btnStart_Click(object sender, EventArgs e) { int iDevice = int.Parse(device_number_textBox.Text); OpenPreviewWindow(); } } }

  Read the article

• ColdFusion Server crash after thousands of HTTP requests

  - by Jason Bristol

  We are running ColdFusion 8 on a windows server 2003 VPS with an API that exposes student records to a partner API through a connector. Our API returns around 50k student records serialized in XML format pretty seamlessly. My question originates when something very frightening happened today when we tested our connector to our partners API. Our entire website and web host went down. We assumed that our host was just having some issues and after 4 hours with no resolution and no response from their customer service we finally got a response from them claiming that they had an "unauthorized user" in their network. After our server was back up we were unable to connect to our website as if the web service or coldfusion itself had froze. This is really where my concern comes from as I fear we may have overloaded the web service. As I mentioned before we tried sending over 50k HTTP POST requests over to our partner's API, however everything stopped after around 1.6k Is this bad practice or is there some sort of rate limiting I can relax somewhere in server configuration? We managed to find a workaround, but it bypasses our connector which is critical to our design. This would have been a one time deal as the purpose of so many requests was to populate our partner's website with current data, after that hourly syncs will keep requests down to around 100 per hour. UPDATE Our partner API is owned and operated by Pardot. We are converting students to prospects by passing student data to their API which unfortunately only seems to accept one student at a time. For that reason we have to do all 50k requests individually. Our server has 4GB of RAM, an Intel Core 2 Duo @ 2.8GHz running Windows Server 2003 SP2. I monitored the server during a 100 student sync, a 400 student sync, and a 1.4k student sync with the following results: 100 students - 2.25GB of Memory, 30-40% CPU utilization, 0.2-0.3% network bandwidth 400 students - 2.30GB of Memory, 30-50% CPU utilization, 0.2-1.0% network bandwidth 1.4k students - 2.30GB of Memory, 30-70% CPU utilization, 0.2-1.0% network bandwidth I know this is a far cry from 50k students, but I don't want to risk taking down our CMS system again assuming that was the cause. To give you a look at our code: <cfif (#getStudents.statusCode# eq "200 OK")> <cftry> <cfloop index="StudentXML" array="#XmlSearch(responseSTUD,'/students/student')#"> <cfset StudentXML = XmlParse(StudentXML)> <cfhttp url="#PARDOT_CMS_UPSERT#" method="post" timeout="10000" > <cfhttpparam type="url" name="user_key" value="#PARDOT_CMS_USERKEY#"> <cfhttpparam type="url" name="api_key" value="#api_key#"> <cfhttpparam type="url" name="email" value="#StudentXML.student.email.XmlText#"> <cfhttpparam type="url" name="first_name" value="#StudentXML.student.first.XmlText#"> <cfhttpparam type="url" name="last_name" value="#StudentXML.student.last.XmlText#"> <cfhttpparam type="url" name="in_cms" value="#StudentXML.student.studentid.XmlText#"> <cfhttpparam type="url" name="company" value="#StudentXML.student.agencyname.XmlText#"> <cfhttpparam type="url" name="country" value="#StudentXML.student.countryname.XmlText#"> <cfhttpparam type="url" name="address_one" value="#StudentXML.student.address.XmlText#"> <cfhttpparam type="url" name="address_two" value="#StudentXML.student.address2.XmlText#"> <cfhttpparam type="url" name="city" value="#StudentXML.student.city.XmlText#"> <cfhttpparam type="url" name="state" value="#StudentXML.student.state_province.XmlText#"> <cfhttpparam type="url" name="zip" value="#StudentXML.student.postalcode.XmlText#"> <cfhttpparam type="url" name="phone" value="#StudentXML.student.phone.XmlText#"> <cfhttpparam type="url" name="fax" value="#StudentXML.student.fax.XmlText#"> <cfhttpparam type="url" name="output" value="simple"> </cfhttp> </cfloop> <cfcatch type="any"> <cfdump var="#cfcatch.Message#"> </cfcatch> </cftry> </cfif> UPDATE 2 I checked the CF logs and found a couple of these: "Error","jrpp-8","06/06/13","16:10:18","CMS-API","Java heap space The specific sequence of files included or processed is: D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm, line: 675 " java.lang.OutOfMemoryError: Java heap space at java.util.Arrays.copyOf(Arrays.java:2882) at java.io.CharArrayWriter.write(CharArrayWriter.java:105) at coldfusion.runtime.CharBuffer.replace(CharBuffer.java:37) at coldfusion.runtime.CharBuffer.replace(CharBuffer.java:50) at coldfusion.runtime.NeoBodyContent.write(NeoBodyContent.java:254) at cfapi2ecfm292155732._factor30(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:675) at cfapi2ecfm292155732._factor31(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:662) at cfapi2ecfm292155732._factor36(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:659) at cfapi2ecfm292155732._factor42(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:657) at cfapi2ecfm292155732._factor37(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm) at cfapi2ecfm292155732._factor44(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:456) at cfapi2ecfm292155732._factor38(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm) at cfapi2ecfm292155732._factor46(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:455) at cfapi2ecfm292155732._factor39(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm) at cfapi2ecfm292155732._factor47(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:453) at cfapi2ecfm292155732.runPage(D:\Clients\www.xxx.com\www\dev.cms\api\v1\api.cfm:1) at coldfusion.runtime.CfJspPage.invoke(CfJspPage.java:192) at coldfusion.tagext.lang.IncludeTag.doStartTag(IncludeTag.java:366) at coldfusion.filter.CfincludeFilter.invoke(CfincludeFilter.java:65) at coldfusion.filter.ApplicationFilter.invoke(ApplicationFilter.java:279) at coldfusion.filter.RequestMonitorFilter.invoke(RequestMonitorFilter.java:48) at coldfusion.filter.MonitoringFilter.invoke(MonitoringFilter.java:40) at coldfusion.filter.PathFilter.invoke(PathFilter.java:86) at coldfusion.filter.ExceptionFilter.invoke(ExceptionFilter.java:70) at coldfusion.filter.ClientScopePersistenceFilter.invoke(ClientScopePersistenceFilter.java:28) at coldfusion.filter.BrowserFilter.invoke(BrowserFilter.java:38) at coldfusion.filter.NoCacheFilter.invoke(NoCacheFilter.java:46) at coldfusion.filter.GlobalsFilter.invoke(GlobalsFilter.java:38) at coldfusion.filter.DatasourceFilter.invoke(DatasourceFilter.java:22) at coldfusion.CfmServlet.service(CfmServlet.java:175) at coldfusion.bootstrap.BootstrapServlet.service(BootstrapServlet.java:89) at jrun.servlet.FilterChain.doFilter(FilterChain.java:86) Looks like I might have crashed the JVM in CF, is there a better way to do this? We are thinking of just exporting all records initially as a CSV file and importing it into Pardot seeing as we will never have to do a request this large again.

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• MySQL is running VERY slow on CentOS 6x (not 5x)

  - by user1032531

  I have two servers: a VPS and a laptop. I recently re-built both of them, and MySQL is running about 20 times slower on the laptop. Both servers used to run CentOS 5.8 and I think MySQL 5.1, and the laptop used to do great so I do not think it is the hardware. For the VPS, my provider installed CentOS 6.4, and then I installed MySQL 5.1.69 using yum with the CentOS repo. For the laptop, I installed CentOS 6.4 basic server and then installed MySQL 5.1.69 using yum with the CentOS repo. my.cnf for both servers are identical, and I have shown below. For both servers, I've also included below the output from SHOW VARIABLES; as well as output from sysbench, file system information, and cpu information. I have tried adding skip-name-resolve, but it didn't help. The matrix below shows the SHOW VARIABLES output from both servers which is different. Again, MySQL was installed the same way, so I do not know why it is different, but it is and I think this might be why the laptop is executing MySQL so slowly. Why is the laptop running MySQL slowly, and how do I fix it? Differences between SHOW VARIABLES on both servers +---------------------------+-----------------------+-------------------------+ | Variable | Value-VPS | Value-Laptop | +---------------------------+-----------------------+-------------------------+ | hostname | vps.site1.com | laptop.site2.com | | max_binlog_cache_size | 4294963200 | 18446744073709500000 | | max_seeks_for_key | 4294967295 | 18446744073709500000 | | max_write_lock_count | 4294967295 | 18446744073709500000 | | myisam_max_sort_file_size | 2146435072 | 9223372036853720000 | | myisam_mmap_size | 4294967295 | 18446744073709500000 | | plugin_dir | /usr/lib/mysql/plugin | /usr/lib64/mysql/plugin | | pseudo_thread_id | 7568 | 2 | | system_time_zone | EST | PDT | | thread_stack | 196608 | 262144 | | timestamp | 1372252112 | 1372252046 | | version_compile_machine | i386 | x86_64 | +---------------------------+-----------------------+-------------------------+ my.cnf for both servers [root@server1 ~]# cat /etc/my.cnf [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid innodb_strict_mode=on sql_mode=TRADITIONAL # sql_mode=STRICT_TRANS_TABLES,NO_ZERO_DATE,NO_ZERO_IN_DATE character-set-server=utf8 collation-server=utf8_general_ci log=/var/log/mysqld_all.log [root@server1 ~]# VPS SHOW VARIABLES Info Same as Laptop shown below but changes per above matrix (removed to allow me to be under the 30000 characters as required by ServerFault) Laptop SHOW VARIABLES Info auto_increment_increment 1 auto_increment_offset 1 autocommit ON automatic_sp_privileges ON back_log 50 basedir /usr/ big_tables OFF binlog_cache_size 32768 binlog_direct_non_transactional_updates OFF binlog_format STATEMENT bulk_insert_buffer_size 8388608 character_set_client utf8 character_set_connection utf8 character_set_database latin1 character_set_filesystem binary character_set_results utf8 character_set_server latin1 character_set_system utf8 character_sets_dir /usr/share/mysql/charsets/ collation_connection utf8_general_ci collation_database latin1_swedish_ci collation_server latin1_swedish_ci completion_type 0 concurrent_insert 1 connect_timeout 10 datadir /var/lib/mysql/ date_format %Y-%m-%d datetime_format %Y-%m-%d %H:%i:%s default_week_format 0 delay_key_write ON delayed_insert_limit 100 delayed_insert_timeout 300 delayed_queue_size 1000 div_precision_increment 4 engine_condition_pushdown ON error_count 0 event_scheduler OFF expire_logs_days 0 flush OFF flush_time 0 foreign_key_checks ON ft_boolean_syntax + -><()~*:""&| ft_max_word_len 84 ft_min_word_len 4 ft_query_expansion_limit 20 ft_stopword_file (built-in) general_log OFF general_log_file /var/run/mysqld/mysqld.log group_concat_max_len 1024 have_community_features YES have_compress YES have_crypt YES have_csv YES have_dynamic_loading YES have_geometry YES have_innodb YES have_ndbcluster NO have_openssl DISABLED have_partitioning YES have_query_cache YES have_rtree_keys YES have_ssl DISABLED have_symlink DISABLED hostname server1.site2.com identity 0 ignore_builtin_innodb OFF init_connect init_file init_slave innodb_adaptive_hash_index ON innodb_additional_mem_pool_size 1048576 innodb_autoextend_increment 8 innodb_autoinc_lock_mode 1 innodb_buffer_pool_size 8388608 innodb_checksums ON innodb_commit_concurrency 0 innodb_concurrency_tickets 500 innodb_data_file_path ibdata1:10M:autoextend innodb_data_home_dir innodb_doublewrite ON innodb_fast_shutdown 1 innodb_file_io_threads 4 innodb_file_per_table OFF innodb_flush_log_at_trx_commit 1 innodb_flush_method innodb_force_recovery 0 innodb_lock_wait_timeout 50 innodb_locks_unsafe_for_binlog OFF innodb_log_buffer_size 1048576 innodb_log_file_size 5242880 innodb_log_files_in_group 2 innodb_log_group_home_dir ./ innodb_max_dirty_pages_pct 90 innodb_max_purge_lag 0 innodb_mirrored_log_groups 1 innodb_open_files 300 innodb_rollback_on_timeout OFF innodb_stats_method nulls_equal innodb_stats_on_metadata ON innodb_support_xa ON innodb_sync_spin_loops 20 innodb_table_locks ON innodb_thread_concurrency 8 innodb_thread_sleep_delay 10000 innodb_use_legacy_cardinality_algorithm ON insert_id 0 interactive_timeout 28800 join_buffer_size 131072 keep_files_on_create OFF key_buffer_size 8384512 key_cache_age_threshold 300 key_cache_block_size 1024 key_cache_division_limit 100 language /usr/share/mysql/english/ large_files_support ON large_page_size 0 large_pages OFF last_insert_id 0 lc_time_names en_US license GPL local_infile ON locked_in_memory OFF log OFF log_bin OFF log_bin_trust_function_creators OFF log_bin_trust_routine_creators OFF log_error /var/log/mysqld.log log_output FILE log_queries_not_using_indexes OFF log_slave_updates OFF log_slow_queries OFF log_warnings 1 long_query_time 10.000000 low_priority_updates OFF lower_case_file_system OFF lower_case_table_names 0 max_allowed_packet 1048576 max_binlog_cache_size 18446744073709547520 max_binlog_size 1073741824 max_connect_errors 10 max_connections 151 max_delayed_threads 20 max_error_count 64 max_heap_table_size 16777216 max_insert_delayed_threads 20 max_join_size 18446744073709551615 max_length_for_sort_data 1024 max_long_data_size 1048576 max_prepared_stmt_count 16382 max_relay_log_size 0 max_seeks_for_key 18446744073709551615 max_sort_length 1024 max_sp_recursion_depth 0 max_tmp_tables 32 max_user_connections 0 max_write_lock_count 18446744073709551615 min_examined_row_limit 0 multi_range_count 256 myisam_data_pointer_size 6 myisam_max_sort_file_size 9223372036853727232 myisam_mmap_size 18446744073709551615 myisam_recover_options OFF myisam_repair_threads 1 myisam_sort_buffer_size 8388608 myisam_stats_method nulls_unequal myisam_use_mmap OFF net_buffer_length 16384 net_read_timeout 30 net_retry_count 10 net_write_timeout 60 new OFF old OFF old_alter_table OFF old_passwords OFF open_files_limit 1024 optimizer_prune_level 1 optimizer_search_depth 62 optimizer_switch index_merge=on,index_merge_union=on,index_merge_sort_union=on,index_merge_intersection=on pid_file /var/run/mysqld/mysqld.pid plugin_dir /usr/lib64/mysql/plugin port 3306 preload_buffer_size 32768 profiling OFF profiling_history_size 15 protocol_version 10 pseudo_thread_id 3 query_alloc_block_size 8192 query_cache_limit 1048576 query_cache_min_res_unit 4096 query_cache_size 0 query_cache_type ON query_cache_wlock_invalidate OFF query_prealloc_size 8192 rand_seed1 rand_seed2 range_alloc_block_size 4096 read_buffer_size 131072 read_only OFF read_rnd_buffer_size 262144 relay_log relay_log_index relay_log_info_file relay-log.info relay_log_purge ON relay_log_space_limit 0 report_host report_password report_port 3306 report_user rpl_recovery_rank 0 secure_auth OFF secure_file_priv server_id 0 skip_external_locking ON skip_name_resolve OFF skip_networking OFF skip_show_database OFF slave_compressed_protocol OFF slave_exec_mode STRICT slave_load_tmpdir /tmp slave_max_allowed_packet 1073741824 slave_net_timeout 3600 slave_skip_errors OFF slave_transaction_retries 10 slow_launch_time 2 slow_query_log OFF slow_query_log_file /var/run/mysqld/mysqld-slow.log socket /var/lib/mysql/mysql.sock sort_buffer_size 2097144 sql_auto_is_null ON sql_big_selects ON sql_big_tables OFF sql_buffer_result OFF sql_log_bin ON sql_log_off OFF sql_log_update ON sql_low_priority_updates OFF sql_max_join_size 18446744073709551615 sql_mode sql_notes ON sql_quote_show_create ON sql_safe_updates OFF sql_select_limit 18446744073709551615 sql_slave_skip_counter sql_warnings OFF ssl_ca ssl_capath ssl_cert ssl_cipher ssl_key storage_engine MyISAM sync_binlog 0 sync_frm ON system_time_zone PDT table_definition_cache 256 table_lock_wait_timeout 50 table_open_cache 64 table_type MyISAM thread_cache_size 0 thread_handling one-thread-per-connection thread_stack 262144 time_format %H:%i:%s time_zone SYSTEM timed_mutexes OFF timestamp 1372254399 tmp_table_size 16777216 tmpdir /tmp transaction_alloc_block_size 8192 transaction_prealloc_size 4096 tx_isolation REPEATABLE-READ unique_checks ON updatable_views_with_limit YES version 5.1.69 version_comment Source distribution version_compile_machine x86_64 version_compile_os redhat-linux-gnu wait_timeout 28800 warning_count 0 VPS Sysbench Info Deleted to stay under 30000 characters. Laptop Sysbench Info [root@server1 ~]# cat sysbench.txt sysbench 0.4.12: multi-threaded system evaluation benchmark Running the test with following options: Number of threads: 8 Doing OLTP test. Running mixed OLTP test Doing read-only test Using Special distribution (12 iterations, 1 pct of values are returned in 75 pct cases) Using "BEGIN" for starting transactions Using auto_inc on the id column Threads started! Time limit exceeded, exiting... (last message repeated 7 times) Done. OLTP test statistics: queries performed: read: 634718 write: 0 other: 90674 total: 725392 transactions: 45337 (755.56 per sec.) deadlocks: 0 (0.00 per sec.) read/write requests: 634718 (10577.78 per sec.) other operations: 90674 (1511.11 per sec.) Test execution summary: total time: 60.0048s total number of events: 45337 total time taken by event execution: 479.4912 per-request statistics: min: 2.04ms avg: 10.58ms max: 85.56ms approx. 95 percentile: 19.70ms Threads fairness: events (avg/stddev): 5667.1250/42.18 execution time (avg/stddev): 59.9364/0.00 [root@server1 ~]# VPS File Info [root@vps ~]# df -T Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/simfs simfs 20971520 16187440 4784080 78% / none tmpfs 6224432 4 6224428 1% /dev none tmpfs 6224432 0 6224432 0% /dev/shm [root@vps ~]# Laptop File Info [root@server1 ~]# df -T Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_server1-lv_root ext4 72383800 4243964 64462860 7% / tmpfs tmpfs 956352 0 956352 0% /dev/shm /dev/sdb1 ext4 495844 60948 409296 13% /boot [root@server1 ~]# VPS CPU Info Removed to stay under the 30000 character limit required by ServerFault Laptop CPU Info [root@server1 ~]# cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz stepping : 13 cpu MHz : 800.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 3591.39 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7100 @ 1.80GHz stepping : 13 cpu MHz : 800.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx lm constant_tsc arch_perfmon pebs bts rep_good aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida dts tpr_shadow vnmi flexpriority bogomips : 3591.39 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: [root@server1 ~]# EDIT New Info requested by shakalandy [root@localhost ~]# cat /proc/meminfo MemTotal: 2044804 kB MemFree: 761464 kB Buffers: 68868 kB Cached: 369708 kB SwapCached: 0 kB Active: 881080 kB Inactive: 246016 kB Active(anon): 688312 kB Inactive(anon): 4416 kB Active(file): 192768 kB Inactive(file): 241600 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 4095992 kB SwapFree: 4095992 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 688428 kB Mapped: 65156 kB Shmem: 4216 kB Slab: 92428 kB SReclaimable: 31260 kB SUnreclaim: 61168 kB KernelStack: 2392 kB PageTables: 28356 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 5118392 kB Committed_AS: 1530212 kB VmallocTotal: 34359738367 kB VmallocUsed: 343604 kB VmallocChunk: 34359372920 kB HardwareCorrupted: 0 kB AnonHugePages: 520192 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 8556 kB DirectMap2M: 2078720 kB [root@localhost ~]# ps aux | grep mysql root 2227 0.0 0.0 108332 1504 ? S 07:36 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/localhost.badobe.com.pid mysql 2319 0.1 24.5 1470068 501360 ? Sl 07:36 0:57 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib64/mysql/plugin --user=mysql --log-error=/var/lib/mysql/localhost.badobe.com.err --pid-file=/var/lib/mysql/localhost.badobe.com.pid root 3579 0.0 0.1 201840 3028 pts/0 S+ 07:40 0:00 mysql -u root -p root 13887 0.0 0.1 201840 3036 pts/3 S+ 18:08 0:00 mysql -uroot -px xxxxxxxxxx root 14449 0.0 0.0 103248 840 pts/2 S+ 18:16 0:00 grep mysql [root@localhost ~]# ps aux | grep mysql root 2227 0.0 0.0 108332 1504 ? S 07:36 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/localhost.badobe.com.pid mysql 2319 0.1 24.5 1470068 501356 ? Sl 07:36 0:57 /usr/sbin/mysqld --basedir=/usr --datadir=/var/lib/mysql --plugin-dir=/usr/lib64/mysql/plugin --user=mysql --log-error=/var/lib/mysql/localhost.badobe.com.err --pid-file=/var/lib/mysql/localhost.badobe.com.pid root 3579 0.0 0.1 201840 3028 pts/0 S+ 07:40 0:00 mysql -u root -p root 13887 0.0 0.1 201840 3048 pts/3 S+ 18:08 0:00 mysql -uroot -px xxxxxxxxxx root 14470 0.0 0.0 103248 840 pts/2 S+ 18:16 0:00 grep mysql [root@localhost ~]# vmstat 1 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 742172 76376 371064 0 0 6 6 78 202 2 1 97 1 0 0 0 0 742164 76380 371060 0 0 0 16 191 467 2 1 93 5 0 0 0 0 742164 76380 371064 0 0 0 0 148 388 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 159 418 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 145 380 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 166 429 2 1 97 0 0 1 0 0 742164 76380 371064 0 0 0 0 148 373 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 149 382 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 168 408 2 0 97 0 0 0 0 0 742164 76380 371064 0 0 0 0 165 394 2 1 98 0 0 0 0 0 742164 76380 371064 0 0 0 0 159 354 2 1 98 0 0 0 0 0 742164 76388 371060 0 0 0 16 180 447 2 0 91 6 0 0 0 0 742164 76388 371064 0 0 0 0 143 344 2 1 98 0 0 0 1 0 742784 76416 370044 0 0 28 580 360 678 3 1 74 23 0 1 0 0 744768 76496 367772 0 0 40 1036 437 865 3 1 53 43 0 0 1 0 747248 76596 365412 0 0 48 1224 561 923 3 2 53 43 0 0 1 0 749232 76696 363092 0 0 32 1132 512 883 3 2 52 44 0 0 1 0 751340 76772 361020 0 0 32 1008 472 872 2 1 52 45 0 0 1 0 753448 76840 358540 0 0 36 1088 512 860 2 1 51 46 0 0 1 0 755060 76936 357636 0 0 28 1012 481 922 2 2 52 45 0 0 1 0 755060 77064 357988 0 0 12 896 444 902 2 1 53 45 0 0 1 0 754688 77148 358448 0 0 16 1096 506 1007 1 1 56 42 0 0 2 0 754192 77268 358932 0 0 12 1060 481 957 1 2 53 44 0 0 1 0 753696 77380 359392 0 0 12 1052 512 1025 2 1 55 42 0 0 1 0 751028 77480 359828 0 0 8 984 423 909 2 2 52 45 0 0 1 0 750524 77620 360200 0 0 8 788 367 869 1 2 54 44 0 0 1 0 749904 77700 360664 0 0 8 928 439 924 2 2 55 43 0 0 1 0 749408 77796 361084 0 0 12 976 468 967 1 1 56 43 0 0 1 0 748788 77896 361464 0 0 12 992 453 944 1 2 54 43 0 1 1 0 748416 77992 361996 0 0 12 784 392 868 2 1 52 46 0 0 1 0 747920 78092 362336 0 0 4 896 382 874 1 1 52 46 0 0 1 0 745252 78172 362780 0 0 12 1040 444 923 1 1 56 42 0 0 1 0 744764 78288 363220 0 0 8 1024 448 934 2 1 55 43 0 0 1 0 744144 78408 363668 0 0 8 1000 461 982 2 1 53 44 0 0 1 0 743648 78488 364148 0 0 8 872 443 888 2 1 54 43 0 0 1 0 743152 78548 364468 0 0 16 1020 511 995 2 1 55 43 0 0 1 0 742656 78632 365024 0 0 12 928 431 913 1 2 53 44 0 0 1 0 742160 78728 365468 0 0 12 996 470 955 2 2 54 44 0 1 1 0 739492 78840 365896 0 0 8 988 447 939 1 2 52 46 0 0 1 0 738872 78996 366352 0 0 12 972 442 928 1 1 55 44 0 1 1 0 738244 79148 366812 0 0 8 948 549 1126 2 2 54 43 0 0 1 0 737624 79312 367188 0 0 12 996 456 953 2 2 54 43 0 0 1 0 736880 79456 367660 0 0 12 960 444 918 1 1 53 46 0 0 1 0 736260 79584 368124 0 0 8 884 414 921 1 1 54 44 0 0 1 0 735648 79716 368488 0 0 12 976 450 955 2 1 56 41 0 0 1 0 733104 79840 368988 0 0 12 932 453 918 1 2 55 43 0 0 1 0 732608 79996 369356 0 0 16 916 444 889 1 2 54 43 0 1 1 0 731476 80128 369800 0 0 16 852 514 978 2 2 54 43 0 0 1 0 731244 80252 370200 0 0 8 904 398 870 2 1 55 43 0 1 1 0 730624 80384 370612 0 0 12 1032 447 977 1 2 57 41 0 0 1 0 730004 80524 371096 0 0 12 984 469 941 2 2 52 45 0 0 1 0 729508 80636 371544 0 0 12 928 438 922 2 1 52 46 0 0 1 0 728888 80756 371948 0 0 16 972 439 943 2 1 55 43 0 0 1 0 726468 80900 372272 0 0 8 960 545 1024 2 1 54 43 0 1 1 0 726344 81024 372272 0 0 8 464 490 1057 1 2 53 44 0 0 1 0 726096 81148 372276 0 0 4 328 441 1063 2 1 53 45 0 1 1 0 726096 81256 372292 0 0 0 296 387 975 1 1 53 45 0 0 1 0 725848 81380 372284 0 0 4 332 425 1034 2 1 54 44 0 1 1 0 725848 81496 372300 0 0 4 308 386 992 2 1 54 43 0 0 1 0 725600 81616 372296 0 0 4 328 404 1060 1 1 54 44 0 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 1 0 725600 81732 372296 0 0 4 328 439 1011 1 1 53 44 0 0 1 0 725476 81848 372308 0 0 0 316 441 1023 2 2 52 46 0 1 1 0 725352 81972 372300 0 0 4 344 451 1021 1 1 55 43 0 2 1 0 725228 82088 372320 0 0 0 328 427 1058 1 1 54 44 0 1 1 0 724980 82220 372300 0 0 4 336 419 999 2 1 54 44 0 1 1 0 724980 82328 372320 0 0 4 320 430 1019 1 1 54 44 0 1 1 0 724732 82436 372328 0 0 0 388 363 942 2 1 54 44 0 1 1 0 724608 82560 372312 0 0 4 308 419 993 1 2 54 44 0 1 0 0 724360 82684 372320 0 0 0 304 421 1028 2 1 55 42 0 1 0 0 724360 82684 372388 0 0 0 0 158 416 2 1 98 0 0 1 1 0 724236 82720 372360 0 0 0 6464 243 855 3 2 84 12 0 1 0 0 724112 82748 372360 0 0 0 5356 266 895 3 1 84 12 0 2 1 0 724112 82764 372380 0 0 0 3052 221 511 2 2 93 4 0 1 0 0 724112 82796 372372 0 0 0 4548 325 1067 2 2 81 16 0 1 0 0 724112 82816 372368 0 0 0 3240 259 829 3 1 90 6 0 1 0 0 724112 82836 372380 0 0 0 3260 309 822 3 2 88 8 0 1 1 0 724112 82876 372364 0 0 0 4680 326 978 3 1 77 19 0 1 0 0 724112 82884 372380 0 0 0 512 207 508 2 1 95 2 0 1 0 0 724112 82884 372388 0 0 0 0 138 361 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 158 397 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 146 395 2 1 98 0 0 2 0 0 724112 82884 372388 0 0 0 0 160 395 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 163 382 1 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 176 422 2 1 98 0 0 1 0 0 724112 82884 372388 0 0 0 0 134 351 2 1 98 0 0 0 0 0 724112 82884 372388 0 0 0 0 190 429 2 1 97 0 0 0 0 0 724104 82884 372392 0 0 0 0 139 358 2 1 98 0 0 0 0 0 724848 82884 372392 0 0 0 4 211 432 2 1 97 0 0 1 0 0 724980 82884 372392 0 0 0 0 166 370 2 1 98 0 0 0 0 0 724980 82884 372392 0 0 0 0 164 397 2 1 98 0 0 ^C [root@localhost ~]# Database size mysql> SELECT table_schema "Data Base Name", sum( data_length + index_length ) / 1024 / 1024 "Data Base Size in MB", sum( data_free )/ 1024 / 1024 "Free Space in MB" FROM information_schema.TABLES GROUP BY table_schema; +--------------------+----------------------+------------------+ | Data Base Name | Data Base Size in MB | Free Space in MB | +--------------------+----------------------+------------------+ | bidjunction | 4.68750000 | 0.00000000 | | information_schema | 0.00976563 | 0.00000000 | | mysql | 0.63899899 | 0.00105286 | +--------------------+----------------------+------------------+ 3 rows in set (0.01 sec) mysql> Before Query mysql> SHOW SESSION STATUS like '%Tmp%'; +-------------------------+-------+ | Variable_name | Value | +-------------------------+-------+ | Created_tmp_disk_tables | 0 | | Created_tmp_files | 6 | | Created_tmp_tables | 0 | +-------------------------+-------+ 3 rows in set (0.00 sec) mysql> After Query mysql> SHOW SESSION STATUS like '%Tmp%'; +-------------------------+-------+ | Variable_name | Value | +-------------------------+-------+ | Created_tmp_disk_tables | 0 | | Created_tmp_files | 6 | | Created_tmp_tables | 2 | +-------------------------+-------+ 3 rows in set (0.00 sec) mysql>

  Read the article

• Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

  - by milkandtang

  I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

  Read the article

• FreeBSD 8.0 - Macbook: Trying to Connect to Wireless

  - by Koroviev

  What Happened A few days ago I installed FreeBSD 8from USB to my Macbook (Core Duo, 13"). The first thing I wanted to do was get my GUI back. I'm new to FreeBSD and it's my first time off of mac or windows, so I had some learning to do. I tried to a make clean install of xorg with ports but it returned many "No address record" errors. I realised I hadn't configured network settings and then the fun started. I ran ifconfig and it found 5 devices: msk0, ath0, fwe0, fwip0, lo0. * ath0 was identified as media: IEEE 802.11 Wireless Ethernet autoselect so it was clear which one I needed. From what I gathered, there are 3 files and two processes involved here: /boot/loader.conf /etc/wpa_supplicant.conf /etc/rc.conf /etc/rc.d/netif wpa_supplicant (which is a part of the former too) I'm certain it's a big simplification, so correct me if I'm wrong here. What I Tried I configured /boot/loader.conf with the few basic settings, and I'm most sure that this file is okay. The other 2 were more puzzling. I tried to make a network package in wpa_supplicant.conf. I found the ssid of the router, but the security wasn't so easy. The routers configuration on security is set to "Auto", with no explanation given. Other options are there, but Auto is selected. Another laptop uses WEP to connect (it's Vista, so I don't know how to get any more info than that), but I never configured it to do it. There's a string labled "wireless key" on the bottom of the router which I entered to set it up a new machine on the network (Windows and Macs, so it was simplified). I never had to choose a security type and only learned about them by installing FreeBSD. So perhaps WEP is what "Auto" means, but I can't find any other evidence. wpa_supplicant.conf seemed to never be correctly configured. I always got errors related to it and WPA_supplicant doesn't work. It gave me "Can't disable/enable WPA in the driver" errors and more once when I enabled -d -d. This was when I was trying some suspect configurations in rc.conf though. Usually it does nothing except hijack the shell and print "CTRL-SCAN-EVENT-RESULT" every 10 seconds. I learned how to clone the ath0 device to a wlandev interface (wlan0). ath0 is associated to it and their connection seems to go smoothly. But the wlan0's connection to the network is the problem. I couldn't create this with rc.conf, I do something wrong and get ifconfig: create: bad value errors whenever it's parsed. I did it via the shell instead. What Now? I scanned with wlan0 today: ifconfig wlan0 list scan It shows my router, even my neighbour's router. It was a relief to finally get some feedback. So wlan0 is UP and detects the router, but it is always status: no carrier. It can't associate with it and I can't figure out why. Running /etc/rc.d/netif start returns almost the same result as ifconfig would. It shows lo0 and wlan0, and sometimes ath0. I still not sure what lo0 is doing. So; how do I associate with it? We can assume it's WEP security based on how the other laptop is setup. I'll give every relevant output here. After boot, with a blank rc.conf this is what ifconfig returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 I run: ifconfig wlan0 create wlandev ath0 It returns: wlan0: bpf attached wlan0: bpf attached wlan0: Ethernet address: xx:xx:xx:xx:xx:xx Ifconfig now returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 1 (2412 Mhz 11b) regdomain 106 indoor ecm authmode OPEN privacy OFF txpower 20 bmiss 7 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 1 wme burst bintval 0 I run: ifconfig wlan0 up ifconfig wlan0 scan It finds my router and displays its details. I can feed it my routers details now, using: ifconfig wlan0 key value key value ... They show up in wlan0 when I run ifconfig, but it still doesn't associate. What details should I feed it, what exactly is needed? What, if anything, should I have in /etc/wpa_supplicant.conf (and if that psk is needed, is it most likely the string I mentioned above)? If I define the ssid in wpa_supplicant.conf, should I still feed it to wlan0? What process should I then use to associate it? 5 .How should I add these things to rc.conf so it will automatically do this at boot? A huge thank you in advance for any help you can give, I've spent hours crawling about the shell and I've learned quite a bit from it (I finally got the hang of vi too, from all that editing). But the sooner this is fixed, the better. *P.S. I was, and still am, wondering where the extra three devices come from (the wireless and wired were all I expected to find). lo0 is up at each boot and /etc/rc.d/netif, I have no idea what it is and can't find it in dmesg. Resources: /etc/loader.conf: Code: if_ath_load="YES" wlan_wep_load="YES" wlan_ccmp_load="YES" wlan_tkip_load="YES" /etc/wpa_supplicant.conf (I emptied it of everything unnecessary, because I was just causing errors) network={ ssid="BTVOYAGER2110-1C" } /etc/rc.conf has no network settings, I commented them out because of errors. There was my attempt to clone ath0 and feed it info, but I did if via the shell instead. I've included the output of dmesg as an attachment, in case it's useful. I'd include the boot text (which appears before login) but I don't know how to catch it into a text file. If it's needed and somebody tells me how, I will (actually, even if it's not needed, how can I view it to read?).

  Read the article

• Does anyone really understand how HFSC scheduling in Linux/BSD works?

  - by Mecki

  I read the original SIGCOMM '97 PostScript paper about HFSC, it is very technically, but I understand the basic concept. Instead of giving a linear service curve (as with pretty much every other scheduling algorithm), you can specify a convex or concave service curve and thus it is possible to decouple bandwidth and delay. However, even though this paper mentions to kind of scheduling algorithms being used (real-time and link-share), it always only mentions ONE curve per scheduling class (the decoupling is done by specifying this curve, only one curve is needed for that). Now HFSC has been implemented for BSD (OpenBSD, FreeBSD, etc.) using the ALTQ scheduling framework and it has been implemented Linux using the TC scheduling framework (part of iproute2). Both implementations added two additional service curves, that were NOT in the original paper! A real-time service curve and an upper-limit service curve. Again, please note that the original paper mentions two scheduling algorithms (real-time and link-share), but in that paper both work with one single service curve. There never have been two independent service curves for either one as you currently find in BSD and Linux. Even worse, some version of ALTQ seems to add an additional queue priority to HSFC (there is no such thing as priority in the original paper either). I found several BSD HowTo's mentioning this priority setting (even though the man page of the latest ALTQ release knows no such parameter for HSFC, so officially it does not even exist). This all makes the HFSC scheduling even more complex than the algorithm described in the original paper and there are tons of tutorials on the Internet that often contradict each other, one claiming the opposite of the other one. This is probably the main reason why nobody really seems to understand how HFSC scheduling really works. Before I can ask my questions, we need a sample setup of some kind. I'll use a very simple one as seen in the image below: Here are some questions I cannot answer because the tutorials contradict each other: What for do I need a real-time curve at all? Assuming A1, A2, B1, B2 are all 128 kbit/s link-share (no real-time curve for either one), then each of those will get 128 kbit/s if the root has 512 kbit/s to distribute (and A and B are both 256 kbit/s of course), right? Why would I additionally give A1 and B1 a real-time curve with 128 kbit/s? What would this be good for? To give those two a higher priority? According to original paper I can give them a higher priority by using a curve, that's what HFSC is all about after all. By giving both classes a curve of [256kbit/s 20ms 128kbit/s] both have twice the priority than A2 and B2 automatically (still only getting 128 kbit/s on average) Does the real-time bandwidth count towards the link-share bandwidth? E.g. if A1 and B1 both only have 64kbit/s real-time and 64kbit/s link-share bandwidth, does that mean once they are served 64kbit/s via real-time, their link-share requirement is satisfied as well (they might get excess bandwidth, but lets ignore that for a second) or does that mean they get another 64 kbit/s via link-share? So does each class has a bandwidth "requirement" of real-time plus link-share? Or does a class only have a higher requirement than the real-time curve if the link-share curve is higher than the real-time curve (current link-share requirement equals specified link-share requirement minus real-time bandwidth already provided to this class)? Is upper limit curve applied to real-time as well, only to link-share, or maybe to both? Some tutorials say one way, some say the other way. Some even claim upper-limit is the maximum for real-time bandwidth + link-share bandwidth? What is the truth? Assuming A2 and B2 are both 128 kbit/s, does it make any difference if A1 and B1 are 128 kbit/s link-share only, or 64 kbit/s real-time and 128 kbit/s link-share, and if so, what difference? If I use the seperate real-time curve to increase priorities of classes, why would I need "curves" at all? Why is not real-time a flat value and link-share also a flat value? Why are both curves? The need for curves is clear in the original paper, because there is only one attribute of that kind per class. But now, having three attributes (real-time, link-share, and upper-limit) what for do I still need curves on each one? Why would I want the curves shape (not average bandwidth, but their slopes) to be different for real-time and link-share traffic? According to the little documentation available, real-time curve values are totally ignored for inner classes (class A and B), they are only applied to leaf classes (A1, A2, B1, B2). If that is true, why does the ALTQ HFSC sample configuration (search for 3.3 Sample configuration) set real-time curves on inner classes and claims that those set the guaranteed rate of those inner classes? Isn't that completely pointless? (note: pshare sets the link-share curve in ALTQ and grate the real-time curve; you can see this in the paragraph above the sample configuration). Some tutorials say the sum of all real-time curves may not be higher than 80% of the line speed, others say it must not be higher than 70% of the line speed. Which one is right or are they maybe both wrong? One tutorial said you shall forget all the theory. No matter how things really work (schedulers and bandwidth distribution), imagine the three curves according to the following "simplified mind model": real-time is the guaranteed bandwidth that this class will always get. link-share is the bandwidth that this class wants to become fully satisfied, but satisfaction cannot be guaranteed. In case there is excess bandwidth, the class might even get offered more bandwidth than necessary to become satisfied, but it may never use more than upper-limit says. For all this to work, the sum of all real-time bandwidths may not be above xx% of the line speed (see question above, the percentage varies). Question: Is this more or less accurate or a total misunderstanding of HSFC? And if assumption above is really accurate, where is prioritization in that model? E.g. every class might have a real-time bandwidth (guaranteed), a link-share bandwidth (not guaranteed) and an maybe an upper-limit, but still some classes have higher priority needs than other classes. In that case I must still prioritize somehow, even among real-time traffic of those classes. Would I prioritize by the slope of the curves? And if so, which curve? The real-time curve? The link-share curve? The upper-limit curve? All of them? Would I give all of them the same slope or each a different one and how to find out the right slope? I still haven't lost hope that there exists at least a hand full of people in this world that really understood HFSC and are able to answer all these questions accurately. And doing so without contradicting each other in the answers would be really nice ;-)

  Read the article

• getting SIGSEGV in std::_List_const_iterator<Exiv2::Exifdatum>::operator++ whilst using jni

  - by HJED

  Hi I'm using jni to access the exiv2 API in my Java project and I'm getting a SIGSEGV error in std::_List_const_iterator::operator++. I'm uncertain how to fix this error. I've tried using high -Xmx values as well as running on both jdk1.6.0 (server and cacao JVMs) and 1.7.0 (server JVM). gdb traceback: #0 0x00007fffa36f2363 in std::_List_const_iterator<Exiv2::Exifdatum>::operator++ (this=0x7ffff7fd3500) at /usr/include/c++/4.4/bits/stl_list.h:223 #1 0x00007fffa36f2310 in std::__distance<std::_List_const_iterator<Exiv2::Exifdatum> > (__first=..., __last=...) at /usr/include/c++/4.4/bits/stl_iterator_base_funcs.h:79 #2 0x00007fffa36f224d in std::distance<std::_List_const_iterator<Exiv2::Exifdatum> > (__first=..., __last=...) at /usr/include/c++/4.4/bits/stl_iterator_base_funcs.h:114 #3 0x00007fffa36f1f27 in std::list<Exiv2::Exifdatum, std::allocator<Exiv2::Exifdatum> >::size (this=0x7fffa4030910) at /usr/include/c++/4.4/bits/stl_list.h:805 #4 0x00007fffa36f1d50 in Exiv2::ExifData::count (this=0x7fffa4030910) at /usr/local/include/exiv2/exif.hpp:518 #5 0x00007fffa36f1d30 in Exiv2::ExifData::empty (this=0x7fffa4030910) at /usr/local/include/exiv2/exif.hpp:516 #6 0x00007fffa36f1763 in getVars (path=0x7fffa401d2f0 "/home/hjed/PC100001.JPG", env=0x6131c8, obj=0x7ffff7fd37a8) at src/main.cpp:146 #7 0x00007fffa36f19d8 in Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv (env=0x6131c8, obj=0x7ffff7fd37a8, path=0x7ffff7fd37a0, obj2=0x7ffff7fd3798) at src/main.cpp:160 #8 0x00007ffff21d9cc8 in ?? () #9 0x00000000fffffffe in ?? () #10 0x00007ffff7fd3740 in ?? () #11 0x0000000000613000 in ?? () #12 0x00007ffff7fd3738 in ?? () #13 0x00007fffaa1076e0 in ?? () #14 0x00007ffff7fd37a8 in ?? () #15 0x00007fffaa108d10 in ?? () #16 0x0000000000000000 in ?? () Java error: # A fatal error has been detected by the Java Runtime Environment: # # SIGSEGV (0xb) at pc=0x00007fac11223363, pid=11905, tid=140378349111040 # # JRE version: 6.0_20-b20 # Java VM: OpenJDK 64-Bit Server VM (19.0-b09 mixed mode linux-amd64 ) # Derivative: IcedTea6 1.9.2 # Distribution: Ubuntu 10.10, package 6b20-1.9.2-0ubuntu2 # Problematic frame: # C [libExiff2-binding.so+0x4363] _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf # # If you would like to submit a bug report, please include # instructions how to reproduce the bug and visit: # https://bugs.launchpad.net/ubuntu/+source/openjdk-6/ # The crash happened outside the Java Virtual Machine in native code. # See problematic frame for where to report the bug. # --------------- T H R E A D --------------- Current thread (0x0000000000dbf000): JavaThread "main" [_thread_in_native, id=11909, stack(0x00007fac61920000,0x00007fac61a21000)] siginfo:si_signo=SIGSEGV: si_errno=0, si_code=128 (), si_addr=0x0000000000000000 Registers: ... Register to memory mapping: RAX=0x6c8948f0245c8948 0x6c8948f0245c8948 is pointing to unknown location RBX=0x00007fac0c042c00 0x00007fac0c042c00 is pointing to unknown location RCX=0x0000000000000000 0x0000000000000000 is pointing to unknown location RDX=0x6c8948f0245c8948 0x6c8948f0245c8948 is pointing to unknown location RSP=0x00007fac61a1f4e0 0x00007fac61a1f4e0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RBP=0x00007fac61a1f4e0 0x00007fac61a1f4e0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RSI=0x00007fac61a1f4f0 0x00007fac61a1f4f0 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE RDI=0x00007fac61a1f500 0x00007fac61a1f500 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R8 =0x00007fac0c054630 0x00007fac0c054630 is pointing to unknown location R9 =0x00007fac61a1f358 0x00007fac61a1f358 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R10=0x00007fac61a1f270 0x00007fac61a1f270 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R11=0x00007fac11223354 0x00007fac11223354: _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0 in /home/hjed/libExiff2-binding.so at 0x00007fac1121f000 R12=0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R13=0x00007fac13ad1be8 {method} - klass: {other class} R14=0x00007fac61a1f7a8 0x00007fac61a1f7a8 is pointing into the stack for thread: 0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE R15=0x0000000000dbf000 "main" prio=10 tid=0x0000000000dbf000 nid=0x2e85 runnable [0x00007fac61a1f000] java.lang.Thread.State: RUNNABLE Top of Stack: (sp=0x00007fac61a1f4e0) ... Instructions: (pc=0x00007fac11223363) ... Stack: [0x00007fac61920000,0x00007fac61a21000], sp=0x00007fac61a1f4e0, free space=1021k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C [libExiff2-binding.so+0x4363] _ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf C [libExiff2-binding.so+0x4310] _ZSt10__distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_St18input_iterator_tag+0x26 C [libExiff2-binding.so+0x424d] _ZSt8distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_+0x36 C [libExiff2-binding.so+0x3f27] _ZNKSt4listIN5Exiv29ExifdatumESaIS1_EE4sizeEv+0x33 C [libExiff2-binding.so+0x3d50] _ZNK5Exiv28ExifData5countEv+0x18 C [libExiff2-binding.so+0x3d30] _ZNK5Exiv28ExifData5emptyEv+0x18 C [libExiff2-binding.so+0x3763] _Z7getVarsPKcP7JNIEnv_P8_jobject+0x3e3 C [libExiff2-binding.so+0x39d8] Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv+0x4b j photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V+0 j photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V+9 j photo.exiv2.Exiv2MetaDataStore.loadData()V+1 j photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V+10 j photo.ImageFile.<init>(Ljava/lang/String;)V+11 j test.Main.main([Ljava/lang/String;)V+67 v ~StubRoutines::call_stub V [libjvm.so+0x428698] V [libjvm.so+0x4275c8] V [libjvm.so+0x432943] V [libjvm.so+0x447f91] C [java+0x3495] JavaMain+0xd75 Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V+0 j photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V+9 j photo.exiv2.Exiv2MetaDataStore.loadData()V+1 j photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V+10 j photo.ImageFile.<init>(Ljava/lang/String;)V+11 j test.Main.main([Ljava/lang/String;)V+67 v ~StubRoutines::call_stub --------------- P R O C E S S --------------- Java Threads: ( => current thread ) 0x00007fac0c028000 JavaThread "Low Memory Detector" daemon [_thread_blocked, id=11924, stack(0x00007fac11532000,0x00007fac11633000)] 0x00007fac0c025800 JavaThread "CompilerThread1" daemon [_thread_blocked, id=11923, stack(0x00007fac11633000,0x00007fac11734000)] 0x00007fac0c022000 JavaThread "CompilerThread0" daemon [_thread_blocked, id=11922, stack(0x00007fac11734000,0x00007fac11835000)] 0x00007fac0c01f800 JavaThread "Signal Dispatcher" daemon [_thread_blocked, id=11921, stack(0x00007fac11835000,0x00007fac11936000)] 0x00007fac0c001000 JavaThread "Finalizer" daemon [_thread_blocked, id=11920, stack(0x00007fac11e2d000,0x00007fac11f2e000)] 0x0000000000e36000 JavaThread "Reference Handler" daemon [_thread_blocked, id=11919, stack(0x00007fac11f2e000,0x00007fac1202f000)] =>0x0000000000dbf000 JavaThread "main" [_thread_in_native, id=11909, stack(0x00007fac61920000,0x00007fac61a21000)] Other Threads: 0x0000000000e2f800 VMThread [stack: 0x00007fac1202f000,0x00007fac12130000] [id=11918] 0x00007fac0c02b000 WatcherThread [stack: 0x00007fac11431000,0x00007fac11532000] [id=11925] ... Heap PSYoungGen total 18432K, used 632K [0x00007fac47210000, 0x00007fac486a0000, 0x00007fac5bc10000) eden space 15808K, 4% used [0x00007fac47210000,0x00007fac472ae188,0x00007fac48180000) from space 2624K, 0% used [0x00007fac48410000,0x00007fac48410000,0x00007fac486a0000) to space 2624K, 0% used [0x00007fac48180000,0x00007fac48180000,0x00007fac48410000) PSOldGen total 42240K, used 0K [0x00007fac1de10000, 0x00007fac20750000, 0x00007fac47210000) object space 42240K, 0% used [0x00007fac1de10000,0x00007fac1de10000,0x00007fac20750000) PSPermGen total 21248K, used 2831K [0x00007fac13810000, 0x00007fac14cd0000, 0x00007fac1de10000) object space 21248K, 13% used [0x00007fac13810000,0x00007fac13ad3d80,0x00007fac14cd0000) Dynamic libraries: ... VM Arguments: jvm_args: -Dfile.encoding=UTF-8 java_command: test.Main Launcher Type: SUN_STANDARD Environment Variables: PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games USERNAME=hjed LD_LIBRARY_PATH=/usr/lib/jvm/java-6-openjdk/jre/lib/amd64/server:/usr/lib/jvm/java-6-openjdk/jre/lib/amd64:/usr/lib/jvm/java-6-openjdk/jre/../lib/amd64 SHELL=/bin/bash DISPLAY=:0.0 Signal Handlers: ... --------------- S Y S T E M --------------- OS:Ubuntu 10.10 (maverick) uname:Linux 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 libc:glibc 2.12.1 NPTL 2.12.1 rlimit: STACK 8192k, CORE 0k, NPROC infinity, NOFILE 1024, AS infinity load average:0.27 0.31 0.30 /proc/meminfo: MemTotal: 4048200 kB MemFree: 106552 kB Buffers: 838212 kB Cached: 1172496 kB SwapCached: 0 kB Active: 1801316 kB Inactive: 1774880 kB Active(anon): 1224708 kB Inactive(anon): 355012 kB Active(file): 576608 kB Inactive(file): 1419868 kB Unevictable: 64 kB Mlocked: 64 kB SwapTotal: 7065596 kB SwapFree: 7065596 kB Dirty: 20 kB Writeback: 0 kB AnonPages: 1565608 kB Mapped: 213424 kB Shmem: 14216 kB Slab: 164812 kB SReclaimable: 102576 kB SUnreclaim: 62236 kB KernelStack: 4784 kB PageTables: 44908 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 9089696 kB Committed_AS: 3676872 kB VmallocTotal: 34359738367 kB VmallocUsed: 332952 kB VmallocChunk: 34359397884 kB HardwareCorrupted: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 48704 kB DirectMap2M: 4136960 kB CPU:total 8 (4 cores per cpu, 2 threads per core) family 6 model 26 stepping 5, cmov, cx8, fxsr, mmx, sse, sse2, sse3, ssse3, sse4.1, sse4.2, popcnt, ht Memory: 4k page, physical 4048200k(106552k free), swap 7065596k(7065596k free) vm_info: OpenJDK 64-Bit Server VM (19.0-b09) for linux-amd64 JRE (1.6.0_20-b20), built on Dec 10 2010 19:45:55 by "buildd" with gcc 4.4.5 main.cpp: jobject toJava(std::auto_ptr<Exiv2::Value> v, const char * type, JNIEnv * env) { jclass stringClass; jmethodID cid; jobject result; stringClass = env->FindClass("photo/exiv2/Value"); cid = env->GetMethodID(stringClass, "<init>", "(Ljava/lang/String;Ljava/lang/Object;)V"); jvalue val; if ((strcmp(type, "String") == 0) || (strcmp(type, "String") == 0)) { val.l = env->NewStringUTF(v->toString().c_str()); } else if (strcmp(type, "Short") == 0) { val.s = v->toLong(0); } else if (strcmp(type, "Long") == 0) { val.j = v->toLong(0); } result = env->NewObject(stringClass, cid, env->NewStringUTF(v->toString().c_str()), val); return result; } void inLoop(std::auto_ptr<MetadataContainer> md, JNIEnv * env, jmethodID mid, jobject obj) { jvalue values[2]; const char* key = md->key().c_str(); values[0].l = env->NewStringUTF(key); /** md->value().toString().c_str(); const char* value = md->typeName(); values[1].l = env->NewStringUTF(value); TODO: do type conversions */ //std::cout << md->typeName() << std::endl; /** const char* type = md->value().toString().c_str(); values[1].l = env->NewStringUTF(type);*/ values[1].l = toJava(md->getValue(), md->typeName(), env); env->CallVoidMethodA(obj, mid, values); } void getVars(const char* path, JNIEnv * env, jobject obj) { //Load image Exiv2::Image::AutoPtr image = Exiv2::ImageFactory::open(path); assert(image.get() != 0); image->readMetadata(); //load method jclass cls = env->GetObjectClass(obj); jmethodID mid = env->GetMethodID(cls, "exiv2_reciveElement", "(Ljava/lang/String;Lphoto/exiv2/Value;)V"); //Load IPTC data /**loadIPTC(image, path, env, obj, mid); loadEXIF(image, path, env, obj, mid);*/ Exiv2::IptcData &iptcData = image->iptcData(); if (mid != NULL) { //is there any IPTC data AND check that method exists if (iptcData.empty()) { std::string error(path); error += ": failed loading IPTC data, there may not be any data"; } else { Exiv2::IptcData::iterator end = iptcData.end(); for (Exiv2::IptcData::iterator md = iptcData.begin(); md != end; ++md) { std::auto_ptr<MetadataContainer> meta(new MetadataContainer(md)); inLoop(meta, env, mid, obj); } } Exiv2::ExifData &exifData = image->exifData(); //is there any Exif data AND check that method exists if (exifData.empty()) { //error occurs here (main.cpp:146) std::string error(path); error += ": failed loading Exif data, there may not be any data"; } else { Exiv2::ExifData::iterator end = exifData.end(); for (Exiv2::ExifData::iterator md = exifData.begin(); md != end; ++md) { std::auto_ptr<MetadataContainer> meta(new MetadataContainer(md)); inLoop(meta, env, mid, obj); } } } else { std::string error(path); error += ": failed to load method"; } } JNIEXPORT void JNICALL Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv(JNIEnv * env, jobject obj, jstring path, jobject obj2) { const char* path2 = env->GetStringUTFChars(path, NULL); getVars(path2, env, obj); env->ReleaseStringUTFChars(path, path2); } Thanks for any help, HJED EDIT This is the output when runing the jvm with the -cacao option: run: null:/usr/local/lib Error: Directory Olympus2 with 1536 entries considered invalid; not read. LOG: [0x00007ff005376700] We received a SIGSEGV and tried to handle it, but we were LOG: [0x00007ff005376700] unable to find a Java method at: LOG: [0x00007ff005376700] LOG: [0x00007ff005376700] PC=0x00007feffe4ee67d LOG: [0x00007ff005376700] LOG: [0x00007ff005376700] Dumping the current stacktrace: at photo.exiv2.Exiv2MetaDataStore.impl_loadFromExiv(Ljava/lang/String;Lphoto/exiv2/Exiv2MetaDataStore;)V(Native Method) at photo.exiv2.Exiv2MetaDataStore.loadFromExiv2()V(Exiv2MetaDataStore.java:38) at photo.exiv2.Exiv2MetaDataStore.loadData()V(Exiv2MetaDataStore.java:29) at photo.exiv2.MetaDataStore.<init>(Lphoto/ImageFile;)V(MetaDataStore.java:33) at photo.exiv2.Exiv2MetaDataStore.<init>(Lphoto/ImageFile;)V(Exiv2MetaDataStore.java:20) at photo.ImageFile.<init>(Ljava/lang/String;)V(ImageFile.java:22) at test.Main.main([Ljava/lang/String;)V(Main.java:28) LOG: [0x00007ff005376700] vm_abort: WARNING, port me to C++ and use os::abort() instead. LOG: [0x00007ff005376700] Exiting... LOG: [0x00007ff005376700] Backtrace (15 stack frames): LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x4ff54) [0x7ff004306f54] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x5ac01) [0x7ff004311c01] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x66e9a) [0x7ff00431de9a] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x76408) [0x7ff00432d408] LOG: [0x00007ff005376700] /usr/lib/jvm/java-6-openjdk/jre/lib/amd64/cacao/libjvm.so(+0x79a4c) [0x7ff004330a4c] LOG: [0x00007ff005376700] /lib/libpthread.so.0(+0xfb40) [0x7ff004d53b40] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNSt20_List_const_iteratorIN5Exiv29ExifdatumEEppEv+0xf) [0x7feffe4ee67d] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZSt10__distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_St18input_iterator_tag+0x26) [0x7feffe4ee62a] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZSt8distanceISt20_List_const_iteratorIN5Exiv29ExifdatumEEENSt15iterator_traitsIT_E15difference_typeES5_S5_+0x36) [0x7feffe4ee567] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNKSt4listIN5Exiv29ExifdatumESaIS1_EE4sizeEv+0x33) [0x7feffe4ee22b] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNK5Exiv28ExifData5countEv+0x18) [0x7feffe4ee054] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_ZNK5Exiv28ExifData5emptyEv+0x18) [0x7feffe4ee034] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(_Z7getVarsPKcP7JNIEnv_P8_jobject+0x3d7) [0x7feffe4ed947] LOG: [0x00007ff005376700] /home/hjed/libExiff2-binding.so(Java_photo_exiv2_Exiv2MetaDataStore_impl_1loadFromExiv+0x4b) [0x7feffe4edcdc] LOG: [0x00007ff005376700] [0x7feffe701ccd] Java Result: 134 BUILD SUCCESSFUL (total time: 0 seconds)

  Read the article

• Reading / Writing from a Unix Socket in Ruby

  - by Olly

  I'm trying to connect, read and write from a UNIX socket in Ruby. It is a stats socket used by haproxy. My code is the following: require 'socket' socket = UNIXSocket.new("/tmp/haproxy.stats.socket") # First attempt: works socket.puts("show stat") while(line = socket.gets) do puts line end # Second attemp: fails socket.puts("show stat") while(line = socket.gets) do puts line end It succeeds the first time, but on the second attempt fails. I'm not sure why. # pxname,svname,qcur,qmax,scur,smax,slim,stot,bin,bout,dreq,dresp,ereq,econ,eresp,wretr,wredis,status,weight,act,bck,chkfail,chkdown,lastchg,downtime,qlimit,pid,iid,sid,throttle,lbtot,tracked,type,rate,rate_lim,rate_max,check_status,check_code,check_duration,hrsp_1xx,hrsp_2xx,hrsp_3xx,hrsp_4xx,hrsp_5xx,hrsp_other,hanafail,req_rate,req_rate_max,req_tot,cli_abrt,srv_abrt, stats,FRONTEND,,,0,0,2000,0,0,0,0,0,0,,,,,OPEN,,,,,,,,,1,1,0,,,,0,0,0,0,,,,0,0,0,0,0,0,,0,0,0,,, stats,BACKEND,0,0,0,0,2000,0,0,0,0,0,,0,0,0,0,UP,0,0,0,,0,22,0,,1,1,0,,0,,1,0,,0,,,,0,0,0,0,0,0,,,,,0,0, legacy_socket,FRONTEND,,,0,0,1000,0,0,0,0,0,0,,,,,OPEN,,,,,,,,,1,2,0,,,,0,0,0,0,,,,0,0,0,0,0,0,,0,0,0,,, all,FRONTEND,,,0,0,10000,0,0,0,0,0,0,,,,,OPEN,,,,,,,,,1,3,0,,,,0,0,0,0,,,,0,0,0,0,0,0,,0,0,0,,, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,1,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,2,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,3,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,4,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,5,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,6,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,22,22,,1,4,7,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,21,21,,1,4,8,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,21,21,,1,4,9,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,socket,0,0,0,0,200,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,21,21,,1,4,10,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, socket_backend,BACKEND,0,0,0,0,0,0,0,0,0,0,,0,0,0,0,DOWN,0,0,0,,1,21,21,,1,4,0,,0,,1,0,,0,,,,0,0,0,0,0,0,,,,,0,0, api_backend,api,0,0,0,0,200,0,0,0,,0,,0,0,0,0,UP,1,1,0,0,0,22,0,,1,5,1,,0,,2,0,,0,L4OK,,0,0,0,0,0,0,0,0,,,,0,0, api_backend,api,0,0,0,0,1,0,0,0,,0,,0,0,0,0,UP,1,1,0,0,0,22,0,,1,5,2,,0,,2,0,,0,L4OK,,0,0,0,0,0,0,0,0,,,,0,0, api_backend,api,0,0,0,0,1,0,0,0,,0,,0,0,0,0,DOWN,1,1,0,0,1,21,21,,1,5,3,,0,,2,0,,0,L4CON,,0,0,0,0,0,0,0,0,,,,0,0, api_backend,BACKEND,0,0,0,0,0,0,0,0,0,0,,0,0,0,0,UP,2,2,0,,0,22,0,,1,5,0,,0,,1,0,,0,,,,0,0,0,0,0,0,,,,,0,0, www_backend,ruby-www,0,0,0,0,10000,0,0,0,,0,,0,0,0,0,UP,1,1,0,0,0,22,0,,1,6,1,,0,,2,0,,0,L4OK,,0,0,0,0,0,0,0,0,,,,0,0, www_backend,BACKEND,0,0,0,0,0,0,0,0,0,0,,0,0,0,0,UP,1,1,0,,0,22,0,,1,6,0,,0,,1,0,,0,,,,0,0,0,0,0,0,,,,,0,0, /Users/Olly/Desktop/haproxy_stats.rb:14:in `write': Broken pipe (Errno::EPIPE) from /Users/Olly/Desktop/haproxy_stats.rb:14:in `puts' from /Users/Olly/Desktop/haproxy_stats.rb:14 What is the problem? Is there a good reference to using UNIX sockets and Ruby?

  Read the article

• Neural Network Always Produces Same/Similar Outputs for Any Input

  - by l33tnerd

  I have a problem where I am trying to create a neural network for Tic-Tac-Toe. However, for some reason, training the neural network causes it to produce nearly the same output for any given input. I did take a look at Artificial neural networks benchmark, but my network implementation is built for neurons with the same activation function for each neuron, i.e. no constant neurons. To make sure the problem wasn't just due to my choice of training set (1218 board states and moves generated by a genetic algorithm), I tried to train the network to reproduce XOR. The logistic activation function was used. Instead of using the derivative, I multiplied the error by output*(1-output) as some sources suggested that this was equivalent to using the derivative. I can put the Haskell source on HPaste, but it's a little embarrassing to look at. The network has 3 layers: the first layer has 2 inputs and 4 outputs, the second has 4 inputs and 1 output, and the third has 1 output. Increasing to 4 neurons in the second layer didn't help, and neither did increasing to 8 outputs in the first layer. I then calculated errors, network output, bias updates, and the weight updates by hand based on http://hebb.mit.edu/courses/9.641/2002/lectures/lecture04.pdf to make sure there wasn't an error in those parts of the code (there wasn't, but I will probably do it again just to make sure). Because I am using batch training, I did not multiply by x in equation (4) there. I am adding the weight change, though http://www.faqs.org/faqs/ai-faq/neural-nets/part2/section-2.html suggests to subtract it instead. The problem persisted, even in this simplified network. For example, these are the results after 500 epochs of batch training and of incremental training. Input |Target|Output (Batch) |Output(Incremental) [1.0,1.0]|[0.0] |[0.5003781562785173]|[0.5009731800870864] [1.0,0.0]|[1.0] |[0.5003740346965251]|[0.5006347214672715] [0.0,1.0]|[1.0] |[0.5003734471544522]|[0.500589332376345] [0.0,0.0]|[0.0] |[0.5003674110937019]|[0.500095157458231] Subtracting instead of adding produces the same problem, except everything is 0.99 something instead of 0.50 something. 5000 epochs produces the same result, except the batch-trained network returns exactly 0.5 for each case. (Heck, even 10,000 epochs didn't work for batch training.) Is there anything in general that could produce this behavior? Also, I looked at the intermediate errors for incremental training, and the although the inputs of the hidden/input layers varied, the error for the output neuron was always +/-0.12. For batch training, the errors were increasing, but extremely slowly and the errors were all extremely small (x10^-7). Different initial random weights and biases made no difference, either. Note that this is a school project, so hints/guides would be more helpful. Although reinventing the wheel and making my own network (in a language I don't know well!) was a horrible idea, I felt it would be more appropriate for a school project (so I know what's going on...in theory, at least. There doesn't seem to be a computer science teacher at my school). EDIT: Two layers, an input layer of 2 inputs to 8 outputs, and an output layer of 8 inputs to 1 output, produces much the same results: 0.5+/-0.2 (or so) for each training case. I'm also playing around with pyBrain, seeing if any network structure there will work. Edit 2: I am using a learning rate of 0.1. Sorry for forgetting about that. Edit 3: Pybrain's "trainUntilConvergence" doesn't get me a fully trained network, either, but 20000 epochs does, with 16 neurons in the hidden layer. 10000 epochs and 4 neurons, not so much, but close. So, in Haskell, with the input layer having 2 inputs & 2 outputs, hidden layer with 2 inputs and 8 outputs, and output layer with 8 inputs and 1 output...I get the same problem with 10000 epochs. And with 20000 epochs. Edit 4: I ran the network by hand again based on the MIT PDF above, and the values match, so the code should be correct unless I am misunderstanding those equations. Some of my source code is at http://hpaste.org/42453/neural_network__not_working; I'm working on cleaning my code somewhat and putting it in a Github (rather than a private Bitbucket) repository. All of the relevant source code is now at https://github.com/l33tnerd/hsann.

  Read the article

• ProFTPd server on Ubuntu getting access denied message when successfully authenticated?

  - by exxoid

  I have a Ubuntu box with a ProFTPD 1.3.4a Server, when I try to log in via my FTP Client I cannot do anything as it does not allow me to list directories; I have tried logging in as root and as a regular user and tried accessing different paths within the FTP Server. The error I get in my FTP Client is: Status: Retrieving directory listing... Command: CDUP Response: 250 CDUP command successful Command: PWD Response: 257 "/var" is the current directory Command: PASV Response: 227 Entering Passive Mode (172,16,4,22,237,205). Command: MLSD Response: 550 Access is denied. Error: Failed to retrieve directory listing Any idea? Here is the config of my proftpd: # # /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file. # To really apply changes, reload proftpd after modifications, if # it runs in daemon mode. It is not required in inetd/xinetd mode. # # Includes DSO modules Include /etc/proftpd/modules.conf # Set off to disable IPv6 support which is annoying on IPv4 only boxes. UseIPv6 off # If set on you can experience a longer connection delay in many cases. IdentLookups off ServerName "Drupal Intranet" ServerType standalone ServerIdent on "FTP Server ready" DeferWelcome on # Set the user and group that the server runs as User nobody Group nogroup MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ # Use this to jail all users in their homes # DefaultRoot ~ # Users require a valid shell listed in /etc/shells to login. # Use this directive to release that constrain. # RequireValidShell off # Port 21 is the standard FTP port. Port 21 # In some cases you have to specify passive ports range to by-pass # firewall limitations. Ephemeral ports can be used for that, but # feel free to use a more narrow range. # PassivePorts 49152 65534 # If your host was NATted, this option is useful in order to # allow passive tranfers to work. You have to use your public # address and opening the passive ports used on your firewall as well. # MasqueradeAddress 1.2.3.4 # This is useful for masquerading address with dynamic IPs: # refresh any configured MasqueradeAddress directives every 8 hours <IfModule mod_dynmasq.c> # DynMasqRefresh 28800 </IfModule> # To prevent DoS attacks, set the maximum number of child processes # to 30. If you need to allow more than 30 concurrent connections # at once, simply increase this value. Note that this ONLY works # in standalone mode, in inetd mode you should use an inetd server # that allows you to limit maximum number of processes per service # (such as xinetd) MaxInstances 30 # Set the user and group that the server normally runs at. # Umask 022 is a good standard umask to prevent new files and dirs # (second parm) from being group and world writable. Umask 022 022 # Normally, we want files to be overwriteable. AllowOverwrite on # Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords: # PersistentPasswd off # This is required to use both PAM-based authentication and local passwords AuthPAMConfig proftpd AuthOrder mod_auth_pam.c* mod_auth_unix.c # Be warned: use of this directive impacts CPU average load! # Uncomment this if you like to see progress and transfer rate with ftpwho # in downloads. That is not needed for uploads rates. # UseSendFile off TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log # Logging onto /var/log/lastlog is enabled but set to off by default #UseLastlog on # In order to keep log file dates consistent after chroot, use timezone info # from /etc/localtime. If this is not set, and proftpd is configured to # chroot (e.g. DefaultRoot or <Anonymous>), it will use the non-daylight # savings timezone regardless of whether DST is in effect. #SetEnv TZ :/etc/localtime <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> # Delay engine reduces impact of the so-called Timing Attack described in # http://www.securityfocus.com/bid/11430/discuss # It is on by default. <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # Alternative authentication frameworks # #Include /etc/proftpd/ldap.conf #Include /etc/proftpd/sql.conf # # This is used for FTPS connections # #Include /etc/proftpd/tls.conf # # Useful to keep VirtualHost/VirtualRoot directives separated # #Include /etc/proftpd/virtuals.con # A basic anonymous configuration, no upload directories. # <Anonymous ~ftp> # User ftp # Group nogroup # # We want clients to be able to login with "anonymous" as well as "ftp" # UserAlias anonymous ftp # # Cosmetic changes, all files belongs to ftp user # DirFakeUser on ftp # DirFakeGroup on ftp # # RequireValidShell off # # # Limit the maximum number of anonymous logins # MaxClients 10 # # # We want 'welcome.msg' displayed at login, and '.message' displayed # # in each newly chdired directory. # DisplayLogin welcome.msg # DisplayChdir .message # # # Limit WRITE everywhere in the anonymous chroot # <Directory *> # <Limit WRITE> # DenyAll # </Limit> # </Directory> # # # Uncomment this if you're brave. # # <Directory incoming> # # # Umask 022 is a good standard umask to prevent new files and dirs # # # (second parm) from being group and world writable. # # Umask 022 022 # # <Limit READ WRITE> # # DenyAll # # </Limit> # # <Limit STOR> # # AllowAll # # </Limit> # # </Directory> # # </Anonymous> # Include other custom configuration files Include /etc/proftpd/conf.d/ UseReverseDNS off <Global> RootLogin on UseFtpUsers on ServerIdent on DefaultChdir /var/www DeleteAbortedStores on LoginPasswordPrompt on AccessGrantMsg "You have been authenticated successfully." </Global> Any idea what could be wrong? Thanks for your help!

  Read the article

• Fibre channel long distance woes

  - by Marki

  I need a fresh pair of eyes. We're using a 15km fibre optic line across which fibrechannel and 10GbE is multiplexed (passive optical CWDM). For FC we have long distance lasers suitable up to 40km (Skylane SFCxx0404F0D). The multiplexer is limited by the SFPs which can do max. 4Gb fibrechannel. The FC switch is a Brocade 5000 series. The respective wavelengths are 1550,1570,1590 and 1610nm for FC and 1530nm for 10GbE. The problem is the 4GbFC fabrics are almost never clean. Sometimes they are for a while even with a lot of traffic on them. Then they may suddenly start producing errors (RX CRC, RX encoding, RX disparity, ...) even with only marginal traffic on them. I am attaching some error and traffic graphs. Errors are currently in the order of 50-100 errors per 5 minutes when with 1Gb/s traffic. Optics Here is the power output of one port summarized (collected using sfpshow on different switches) SITE-A units=uW (microwatt) SITE-B ********************************************** FAB1 SW1 TX 1234.3 RX 49.1 SW3 1550nm (ko) RX 95.2 TX 1175.6 FAB2 SW2 TX 1422.0 RX 104.6 SW4 1610nm (ok) RX 54.3 TX 1468.4 What I find curious at this point is the asymmetry in the power levels. While SW2 transmits with 1422uW which SW4 receives with 104uW, SW2 only receives the SW4 signal with similar original power only with 54uW. Vice versa for SW1-3. Anyway the SFPs have RX sensitivity down to -18dBm (ca. 20uW) so in any case it should be fine... But nothing is. Some SFPs have been diagnosed as malfunctioning by the manufacturer (the 1550nm ones shown above with "ko"). The 1610nm ones apparently are ok, they have been tested using a traffic generator. The leased line has also been tested more than once. All is within tolerances. I'm awaiting the replacements but for some reason I don't believe it will make things better as the apparently good ones don't produce ZERO errors either. Earlier there was active equipment involved (some kind of 4GFC retimer) before putting the signal on the line. No idea why. That equipment was eliminated because of the problems so we now only have: the long distance laser in the switch, (new) 10m LC-SC monomode cable to the mux (for each fabric), the leased line, the same thing but reversed on the other side of the link. FC switches Here is a port config from the Brocade portcfgshow (it's like that on both sides, obviously) Area Number: 0 Speed Level: 4G Fill Word(On Active) 0(Idle-Idle) Fill Word(Current) 0(Idle-Idle) AL_PA Offset 13: OFF Trunk Port ON Long Distance LS VC Link Init OFF Desired Distance 32 Km Reserved Buffers 70 Locked L_Port OFF Locked G_Port OFF Disabled E_Port OFF Locked E_Port OFF ISL R_RDY Mode OFF RSCN Suppressed OFF Persistent Disable OFF LOS TOV enable OFF NPIV capability ON QOS E_Port OFF Port Auto Disable: OFF Rate Limit OFF EX Port OFF Mirror Port OFF Credit Recovery ON F_Port Buffers OFF Fault Delay: 0(R_A_TOV) NPIV PP Limit: 126 CSCTL mode: OFF Forcing the links to 2GbFC produces no errors, but we bought 4GbFC and we want 4GbFC. I don't know where to look anymore. Any ideas what to try next or how to proceed? If we can't make 4GbFC work reliably I wonder what the people working with 8 or 16 do... I don't assume that "a few errors here and there" are acceptable. Oh and BTW we are in contact with everyone of the manufacturers (FC switch, MUX, SFPs, ...) Except for the SFPs to be changed (some have been changed before) nobody has a clue. Brocade SAN Health says the fabric is ok. MUX, well, it's passive, it's only a prism, nature at it's best. Any shots in the dark? APPENDIX: Answers to your questions @Chopper3: This is the second generation of Brocades exhibiting the problem. Before we had 5000s, now we have 5100s. In the beginning when we still had the active MUX we rented a longdistance laser once to put it into the switch directly in order to make tests for a day, during that day of course it was clean. But as I said, sometimes it's clean just like that. And sometimes it's not. Alternative switches would mean to rebuild the entire SAN with those only to test. Alternative SFPs, well they're hard to come by just like that. @longneck: The line is rented. It's a dark fibre (9um monomode) so there's noone else on it. Sure there are splices. I can't go and look but I have to trust they have been done correctly. As I said the line has been checked and rechecked (using an optical time-domain reflectometer). Obviously you don't have all this equipment yourself because it's way too expensive. @mdpc: What would be the "wrong" type of cable according to you? Up to the switch everything is monomode, yes. The connectors are the correct ones too. Yeah I know there are the green ones where the fibre is cut off at a certain angle etc. But we have the correct ones for all that I know. Progress Report #1 We have had two fabrics (=2x2 switches) with Brocade 5100s with FabricOS 6.4.1 and two fabrics (another 2x4 switches) on FabricOS 7.0.2. On the longdistance ISLs (one in each fabric) it turned out that with FOS 6.4.1 setting it to long distance issues warnings about the VC Init setting and consequently the fill word. But those are only warnings. FOS 7.0.2 requires you to do modifications to VCI and the fillword for long distance links. Setting FOS 6.4.1 to the LS (long-distance static distance) setting with wrong VCI and fillword setting made the whole fabric inoperational (stuck in an SCN loop, use fabriclog -s to see, you don't see it anywhere else, no port error counters or anything increasing). Currently I'm giving the one fabric with the IMHO more correct settings a beating and it seems to do fine, whereas the other one without much traffic still has errors here and there. In short: We have eliminated the active part of the MUX (the FC retimer). We are putting the long distance SFPs into the end equipment themselves. Just to be sure we bought new monomode cables to connect the end equipment to the remaining passive part of the MUX. We are now trying out several long distance configs. It's almost black magic. Everything that happens is mostly empirical, noone seems to have a clue what are the exact reasons to do something. ("We have tried this, and it didn't work, then we tried that and it worked, so we stuck with that." But noone really seems to know why.) I'll keep you updated. Progress Report #2 We got the new lasers for one of the fabrics on warranty. It's ultra clean even on 4GbFC. They're transmitting with roughly 2mW (3dBm) whereas the others are only at 1.5mW (1.5dBm) although that should really be enough. The other fabric (where the lasers are apparently ok) still produces one or two CRCs infrequently. Using sfpshow the SFP producing the actual RX errors shows Status/Ctrl: 0x82 Alarm flags[0,1] = 0x5, 0x40 Warn Flags[0,1] = 0x5, 0x40 Now I'll have to find out what that means. Not sure if it was there before. Well I'll first clear my head with a week of vacation. 8-)

  Read the article

• Trying to configure HWIC-3G-HSPA

  - by user1174838

  I'm trying to configure a couple of Cisco 1941 routes. The are both identical routers. Each as a HWIC-1T (Smart Serial interface) and a HWIC-3G-HSPA 3G interface. These routers are to be sent to remote sites. We have connectivity to one of the sites but if remote site A gors down we lose connectivity to remote site B. The HWIC-1T is the primary WAN interface using frame relay joining the two remote sites We want the HWIC-3G-HSPA to be usable for direct connectivity from head office to remote site B, and also the HWIC-3G-HSPA is do be used for comms between the remote sites when the frame relay is down (happens quite a bit). I initialy tried to do dynamic routing using EIGRP however in my lab setup of laptop - 1941 - 1941 - laptop, I was unable to get end to end connectivity. I later settled on static routing and have got end to end connectivity but only over frame relay, not the HWIC-3G-HSPA. The sanitized running config for remote site A: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteA ! boot-start-marker boot-end-marker ! ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" ! username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.2.5 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.2 255.255.255.252 encapsulation frame-relay cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.3.0 255.255.255.0 10.1.1.1 permanent ip route 192.168.3.0 255.255.255.0 Cellular0/1/0 210 permanent ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The sanitized running config for remote site B: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteB ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! no ip domain lookup ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.3.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.1 255.255.255.252 encapsulation frame-relay clock rate 2000000 cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi frame-relay intf-type dce ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored ppp ipcp dns request cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.2.0 255.255.255.0 10.1.1.2 permanent ip route 192.168.2.0 255.255.255.0 Cellular0/1/0 210 permanent ! kron occurrence PING in 1 recurring policy-list ICMP ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The last problem I'm having is the 3G interfaces go down after only a few minutes of inactivity. I've tried using kron to ping the local HWIC-3G-HSPA interface (cellular 0/1/0) every minute but that hasn't been successful. Manually pinging the IP assigned (by the telco) to ce0/1/0 does bring the interface up. Any ideas? Thanks

  Read the article

• Where would you document standardized complex data that is passed between many objects and methods?

  - by Eli

  Hi All, I often find myself with fairly complex data that represents something that my objects will be working on. For example, in a task-list app, several objects might work with an array of tasks, each of which has attributes, temporal expressions, sub tasks and sub sub tasks, etc. One object will collect data from web forms, standardize it into a format consumable by the class that will save them to the database, another object will pull them from the database, put them in the standard format and pass them to the display object, or the update object, etc. The data itself can become a fairly complex series of arrays and sub arrays, representing a 'task' or list of tasks. For example, the below might be one entry in a task list, in the format that is consumable by the various objects that will work on it. Normally, I just document this in a file somewhere with an example. However, I am thinking about the best way to add it to something like PHPDoc, or another standard doc system. Where would you document your consumable data formats that are for many or all of the objects / methods in your app? Array ( [Meta] => Array ( //etc. ) [Sched] => Array ( [SchedID] => 32 [OwnerID] => 2 [StatusID] => 1 [DateFirstTask] => 2011-02-28 [DateLastTask] => [MarginMonths] => 3 ) [TemporalExpressions] => Array ( [0] => Array ( [type] => dw [TemporalExpID] => 3 [ord] => 2 [day] => 6 [month] => 4 ) [1] => Array ( [type] => dm [TemporalExpID] => 32 [day] => 28 [month] => 2 ) ) [Task] => Array ( [SchedTaskID] => 32 [SchedID] => 32 [OwnerID] => 2 [UserID] => 5 [ClientID] => 9 [Title] => Close Prior Year [Body] => [DueTime] => ) [SubTasks] => Array ( [101] => Array ( [SchedSubTaskID] => 101 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Review Profit and Loss by Class [Body] => [DueDiff] => 0 ) [102] => Array ( [SchedSubTaskID] => 102 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Review Balance Sheet [Body] => [DueDiff] => 0 ) [103] => Array ( [SchedSubTaskID] => 103 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Review Current Year for Prior Year Expenses to Accrue [Body] => Look at Journal Entries that are templates as well. [DueDiff] => 0 ) [104] => Array ( [SchedSubTaskID] => 104 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Review Prior Year Membership from 11/1 - 12/31 to Accrue to Current Year [Body] => [DueDiff] => 0 ) [105] => Array ( [SchedSubTaskID] => 105 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Enter Vacation Accrual [Body] => [DueDiff] => 0 ) [106] => Array ( [SchedSubTaskID] => 106 [ParentST] => 105 [RootT] => 32 [UserID] => 2 [Title] => Email Peter requesting Vacation Status of Employees at Year End [Body] => We need Employee Name, Rate and Days of Vacation left to use. We also need to know if the employee used any of the prior year's vacation. [DueDiff] => 43 ) [107] => Array ( [SchedSubTaskID] => 107 [ParentST] => [RootT] => 32 [UserID] => 2 [Title] => Grants Receivable at Year End [Body] => [DueDiff] => 0 ) [108] => Array ( [SchedSubTaskID] => 108 [ParentST] => 107 [RootT] => 32 [UserID] => 2 [Title] => Email Peter Requesting if there were and Grants Receivable at year end [Body] => [DueDiff] => 43 ) ) )

  Read the article

• SSL confirmation dialog popup auto closes in IE8 when re-accessing a JNLP file

  - by haylem

  I'm having this very annoying problem to troubleshoot and have been going at it for way too many days now, so have a go at it. The Environment We have 2 app-servers, which can be located on either the same machine or 2 different machines, and use the same signing certificate, and host 2 different web-apps. Though let's say, for the sake of our study case here, that they are on the same physical machine. So, we have: https://company.com/webapp1/ https://company.com/webapp2/ webapp1 is GWT-based rich-client which contains on one of its screens a menu with an item that is used to invoke a Java WebStart Client located on webapp2. It does so by performing a simple window.open call via this GWT call: Window.open("https://company.com/webapp2/app.jnlp", "_blank", null); Expected Behavior User merrilly goes to webapp1 User navigates to menu entry to start the WebStart app and clicks on it browser fires off a separate window/dialog which, depending on the browser and its security settings, will: request confirmation to navigate to this secure site, directly download the file, and possibly auto-execute a javaws process if there's a file association, otherwise the user can simply click on the file and start the app (or go about doing whatever it takes here). If you close the app, close the dialog, and re-click the menu entry, the same thing should happen again. Actual Behavior On Anything but God-forsaken IE 8 (Though I admit there's also all the god-forsaken pre-IE8 stuff, but the Requirements Lords being merciful we have already recently managed to make them drop these suckers. That was close. Let's hold hands and say a prayer of gratitude.) Stuff just works. JNLP gets downloaded, app executes just fine, you can close the app and re-do all the steps and it will restart happily. People rejoice. Puppies are safe and play on green hills in the sunshine. Developers can go grab a coffee and move on to more meaningful and rewarding tasks, like checking out on SO questions. Chrome doesn't want to execute the JNLP, but who cares? Customers won't get RSI from clicking a file every other week. On God-forsaken IE8 On the first visit, the dialog opens and requests confirmation for the user to continue to webapp2, though it could be unsafe (here be dragons, I tell you). The JNLP downloads and auto-opens, the app start. Your breathing is steady and slow. You close the app, close that SSL confirmation dialog, and re-click the menu entry. The dialog opens and auto-closes. Nothing starts, the file wasn't downloaded to any known location and Fiddler just reports the connection was closed. If you close IE and reach that menu item to click it again, it is now back to working correctly. Until you try again during the same session, of course. Your heart-rate goes up, you get some more coffee to make matters worse, and start looking for plain tickets online and a cheap but heavy golf-club on an online auction site to go clubbing baby polar seals to avenge your bloodthirst, as the gates to the IE team in Redmond are probably more secured than an ice block, as one would assume they get death threats often. Plus, the IE9 and IE10 teams are already hard at work fxing the crap left by their predecessors, so maybe you don't want to be too hard on them, and you don't have money to waste on a PI to track down the former devs responsible for this mess. Added Details I have come across many problems with IE8 not downloading files over SSL when it uses a no-cache header. This was indeed one of our problems, which seems to be worked out now. It downloads files fine, webapp2 uses the following headers to serve the JNLP file: response.setHeader("Cache-Control", "private, must-revalidate"); // IE8 happy response.setHeader("Pragma", "private"); // IE8 happy response.setHeader("Expires", "0"); // IE8 happy response.setHeader("Access-Control-Allow-Origin", "*"); // allow to request via cross-origin AJAX response.setContentType("application/x-java-jnlp-file"); // please exec me As you might have inferred, we get some confirmation dialog because there's something odd with the SSL certificate. Unfortunately I have no control over that. Assuming that's only temporary and for development purposes as we usually don't get our hands on the production certs. So the SSL cert is expired and doesn't specify the server. And the confirmation dialog. Wouldn't be that bad if it weren't for IE, as other browsers don't care, just ask for confirmation, and execute as expected and consistantly. Please, pretty please, help me, or I might consider sacrificial killings as an option. And I think I just found a decently prized stainless steel golf-club, so I'm right on the edge of gore. Side Notes Might actually be related to IE8 window.open SSL Certificate issue. Though it doesn't explain why the dialog would auto-close (that really is beyong me...), it could help to not have the confirmation dialog and not need the dialog at all. For instance, I was thinking that just having a simple URL in that menu instead of have it entirely managed by GWT code to invoke a Window.open would solve the problem. But I don't have control on that menu, and also I'm very curious how this could be fixed otherwise and why the hell it happens in the first place...

  Read the article

• C++0x rvalue references - lvalues-rvalue binding

  - by Doug

  This is a follow-on question to http://stackoverflow.com/questions/2748866/c0x-rvalue-references-and-temporaries In the previous question, I asked how this code should work: void f(const std::string &); //less efficient void f(std::string &&); //more efficient void g(const char * arg) { f(arg); } It seems that the move overload should probably be called because of the implicit temporary, and this happens in GCC but not MSVC (or the EDG front-end used in MSVC's Intellisense). What about this code? void f(std::string &&); //NB: No const string & overload supplied void g1(const char * arg) { f(arg); } void g2(const std::string & arg) { f(arg); } It seems that, based on the answers to my previous question that function g1 is legal (and is accepted by GCC 4.3-4.5, but not by MSVC). However, GCC and MSVC both reject g2 because of clause 13.3.3.1.4/3, which prohibits lvalues from binding to rvalue ref arguments. I understand the rationale behind this - it is explained in N2831 "Fixing a safety problem with rvalue references". I also think that GCC is probably implementing this clause as intended by the authors of that paper, because the original patch to GCC was written by one of the authors (Doug Gregor). However, I don't this is quite intuitive. To me, (a) a const string & is conceptually closer to a string && than a const char *, and (b) the compiler could create a temporary string in g2, as if it were written like this: void g2(const std::string & arg) { f(std::string(arg)); } Indeed, sometimes the copy constructor is considered to be an implicit conversion operator. Syntactically, this is suggested by the form of a copy constructor, and the standard even mentions this specifically in clause 13.3.3.1.2/4, where the copy constructor for derived-base conversions is given a higher conversion rank than other implicit conversions: A conversion of an expression of class type to the same class type is given Exact Match rank, and a conversion of an expression of class type to a base class of that type is given Conversion rank, in spite of the fact that a copy/move constructor (i.e., a user-defined conversion function) is called for those cases. (I assume this is used when passing a derived class to a function like void h(Base), which takes a base class by value.) Motivation My motivation for asking this is something like the question asked in http://stackoverflow.com/questions/2696156/how-to-reduce-redundant-code-when-adding-new-c0x-rvalue-reference-operator-over ("How to reduce redundant code when adding new c++0x rvalue reference operator overloads"). If you have a function that accepts a number of potentially-moveable arguments, and would move them if it can (e.g. a factory function/constructor: Object create_object(string, vector<string>, string) or the like), and want to move or copy each argument as appropriate, you quickly start writing a lot of code. If the argument types are movable, then one could just write one version that accepts the arguments by value, as above. But if the arguments are (legacy) non-movable-but-swappable classes a la C++03, and you can't change them, then writing rvalue reference overloads is more efficient. So if lvalues did bind to rvalues via an implicit copy, then you could write just one overload like create_object(legacy_string &&, legacy_vector<legacy_string> &&, legacy_string &&) and it would more or less work like providing all the combinations of rvalue/lvalue reference overloads - actual arguments that were lvalues would get copied and then bound to the arguments, actual arguments that were rvalues would get directly bound. Questions My questions are then: Is this a valid interpretation of the standard? It seems that it's not the conventional or intended one, at any rate. Does it make intuitive sense? Is there a problem with this idea that I"m not seeing? It seems like you could get copies being quietly created when that's not exactly expected, but that's the status quo in places in C++03 anyway. Also, it would make some overloads viable when they're currently not, but I don't see it being a problem in practice. Is this a significant enough improvement that it would be worth making e.g. an experimental patch for GCC?

  Read the article

• Database file is inexplicably locked during SQLite commit

  - by sweeney

  Hello, I'm performing a large number of INSERTS to a SQLite database. I'm using just one thread. I batch the writes to improve performance and have a bit of security in case of a crash. Basically I cache up a bunch of data in memory and then when I deem appropriate, I loop over all of that data and perform the INSERTS. The code for this is shown below: public void Commit() { using (SQLiteConnection conn = new SQLiteConnection(this.connString)) { conn.Open(); using (SQLiteTransaction trans = conn.BeginTransaction()) { using (SQLiteCommand command = conn.CreateCommand()) { command.CommandText = "INSERT OR IGNORE INTO [MY_TABLE] (col1, col2) VALUES (?,?)"; command.Parameters.Add(this.col1Param); command.Parameters.Add(this.col2Param); foreach (Data o in this.dataTemp) { this.col1Param.Value = o.Col1Prop; this. col2Param.Value = o.Col2Prop; command.ExecuteNonQuery(); } } this.TryHandleCommit(trans); } conn.Close(); } } I now employ the following gimmick to get the thing to eventually work: private void TryHandleCommit(SQLiteTransaction trans) { try { trans.Commit(); } catch (Exception e) { Console.WriteLine("Trying again..."); this.TryHandleCommit(trans); } } I create my DB like so: public DataBase(String path) { //build connection string SQLiteConnectionStringBuilder connString = new SQLiteConnectionStringBuilder(); connString.DataSource = path; connString.Version = 3; connString.DefaultTimeout = 5; connString.JournalMode = SQLiteJournalModeEnum.Persist; connString.UseUTF16Encoding = true; using (connection = new SQLiteConnection(connString.ToString())) { //check for existence of db FileInfo f = new FileInfo(path); if (!f.Exists) //build new blank db { SQLiteConnection.CreateFile(path); connection.Open(); using (SQLiteTransaction trans = connection.BeginTransaction()) { using (SQLiteCommand command = connection.CreateCommand()) { command.CommandText = DataBase.CREATE_MATCHES; command.ExecuteNonQuery(); command.CommandText = DataBase.CREATE_STRING_DATA; command.ExecuteNonQuery(); //TODO add logging } trans.Commit(); } connection.Close(); } } } I then export the connection string and use it to obtain new connections in different parts of the program. At seemingly random intervals, though at far too great a rate to ignore or otherwise workaround this problem, I get unhandled SQLiteException: Database file is locked. This occurs when I attempt to commit the transaction. No errors seem to occur prior to then. This does not always happen. Sometimes the whole thing runs without a hitch. No reads are being performed on these files before the commits finish. I have the very latest SQLite binary. I'm compiling for .NET 2.0. I'm using VS 2008. The db is a local file. All of this activity is encapsulated within one thread / process. Virus protection is off (though I think that was only relevant if you were connecting over a network?). As per Scotsman's post I have implemented the following changes: Journal Mode set to Persist DB files stored in C:\Docs + Settings\ApplicationData via System.Windows.Forms.Application.AppData windows call No inner exception Witnessed on two distinct machines (albeit very similar hardware and software) Have been running Process Monitor - no extraneous processes are attaching themselves to the DB files - the problem is definitely in my code... Does anyone have any idea whats going on here? I know I just dropped a whole mess of code, but I've been trying to figure this out for way too long. My thanks to anyone who makes it to the end of this question! brian UPDATES: Thanks for the suggestions so far! I've implemented many of the suggested changes. I feel that we are getting closer to the answer...however... The code above technically works however it is non-deterministic! It is not guaranteed to do anything aside from spin in neutral forever. In practice it seems to work somewhere between the 1st and 10th iteration. If i batch my commits at a reasonable interval damage will be mitigated but I really do not want to leave things in this state... More suggestions welcome!

  Read the article

• Cisco ASA5505 8.2 Multiple Outside IP to Multiple Inside IP

  - by GriffJ

  Trying to setup ASA5505. Semi working but having issues with accessing services from the outside. ASA5505 Basic License, Version 8.2. (plus upgrade to unlimited inside hosts). Alert: I'm a Cisco Noob. 321.321.39.X is a place holder for privacy. I came up with this config and tested it tonight. ASA Version 8.2(1) ! hostname <removed> domain-name <removed> enable password <removed> encrypted passwd <removed> encrypted names ! interface Vlan1 nameif inside security-level 100 ip address 172.21.36.1 255.255.252.0 ! interface Vlan2 nameif outside security-level 0 ip address 321.321.39.10 255.255.255.248 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name <removed> access-list outside_inbound extended permit tcp any host 321.321.39.10 eq pptp access-list outside_inbound extended permit tcp any host 321.321.39.11 eq https access-list outside_inbound extended permit tcp any host 321.321.39.11 eq 993 access-list outside_inbound extended permit tcp any host 321.321.39.11 eq smtp access-list outside_inbound extended permit tcp any host 321.321.39.11 eq 1001 access-list outside_inbound extended permit tcp any host 321.321.39.11 eq 465 access-list outside_inbound extended permit tcp any host 321.321.39.11 eq domain access-list outside_inbound extended permit udp any eq domain host 321.321.39.11 eq domain access-list outside_inbound extended permit tcp any host 321.321.39.12 eq www access-list outside_inbound extended permit tcp any host 321.321.39.12 eq https access-list outside_inbound extended permit tcp any host 321.321.39.13 eq www access-list outside_inbound extended permit tcp any host 321.321.39.13 eq https access-list outside_inbound extended permit icmp any any echo-reply access-list outside_inbound extended permit icmp any any source-quench access-list outside_inbound extended permit icmp any any unreachable access-list outside_inbound extended permit icmp any any time-exceeded access-list outside_inbound extended permit icmp any any traceroute access-list outside_inbound extended permit icmp any any echo pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 2 321.321.39.11-321.321.39.14 netmask 255.255.255.248 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface pptp 172.21.37.20 pptp netmask 255.255.255.255 static (inside,outside) 321.321.39.11 172.21.37.14 netmask 255.255.255.255 static (inside,outside) 321.321.39.12 172.21.37.24 netmask 255.255.255.255 static (inside,outside) 321.321.39.13 172.21.37.17 netmask 255.255.255.255 access-group outside_inbound in interface outside route outside 0.0.0.0 0.0.0.0 321.321.39.9 1 route inside 192.168.15.0 255.255.255.0 172.21.36.52 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 172.21.36.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 172.21.36.0 255.255.252.0 inside telnet timeout 60 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect pptp inspect ipsec-pass-thru inspect http ! service-policy global_policy global prompt hostname context The servers that had static forwards did not have any outside network access. couldn't ping google.com for instance. mail server couldn't Domain POP the Barracuda spam filter from our ISP etc. So after doing some reading I removed the statics for 172.21.37.11, 12 and 13, and replaced those three with what's below.. static (inside,outside) tcp 321.321.39.11 https 172.21.37.14 https netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.11 993 172.21.37.14 993 netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.11 smtp 172.21.37.14 smtp netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.11 1001 172.21.37.14 1001 netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.11 465 172.21.37.14 465 netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.11 domain 172.21.37.14 domain netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.12 www 172.21.37.24 www netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.12 https 172.21.37.24 https netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.13 www 172.21.37.17 www netmask 255.255.255.255 static (inside,outside) tcp 321.321.39.13 https 172.21.37.17 https netmask 255.255.255.255 Now the servers (for instance 172.21.37.14) could ping the outside world again. Mail started flowing (Domain POP was successful) etc. etc. But I forgot to check if webmail worked from the outside admittedly. But the webservers at 172.21.37.17 and 172.21.37.24 still didn't respond from the outside world. Although I was able to PPTP VPN in on 321.321.39.10 (interface) which is the outside interface IP address. and it is static mapped to 172.21.37.20. So I'm thinking there must be something wrong with NAT somewhere? no response from 321.321.39.11 to 321.321.39.14.. Could anyone look over the config and please let me know what I've done wrong? Is there something I've missed? well obviously but.. please help! Thank you.

  Read the article

• Threads to make video out of images

  - by masood

  updates: I think/ suspect the imageIO is not thread safe. shared by all threads. the read() call might use resources that are also shared. Thus it will give the performance of a single thread no matter how many threads used. ? if its correct . what is the solution (in practical code) Single request and response model at one time do not utilizes full network/internet bandwidth, thus resulting in low performance. (benchmark is of half speed utilization or even lower) This is to make a video out of an IP cam that gives a new image on each request. http://149.5.43.10:8001/snapshot.jpg It makes a delay of 3 - 8 seconds no matter what I do. Changed thread no. and thread time intervals, debugged the code by System.out.println statements to see if threads work. All seems normal. Any help? Please show some practical code. You may modify mine. This code works (javascript) with much smoother frame rate and max bandwidth usage. but the later code (java) dont. same 3 to 8 seconds gap. <!DOCTYPE html> <html> <head> <script type="text/javascript"> (function(){ var img="/*url*/"; var interval=50; var pointer=0; function showImg(image,idx) { if(idx<=pointer) return; document.body.replaceChild(image,document.getElementsByTagName("img")[0]); pointer=idx; preload(); } function preload() { var cache=null,idx=0;; for(var i=0;i<5;i++) { idx=Date.now()+interval*(i+1); cache=new Image(); cache.onload=(function(ele,idx){return function(){showImg(ele,idx);};})(cache,idx); cache.src=img+"?"+idx; } } window.onload=function(){ document.getElementsByTagName("img")[0].onload=preload; document.getElementsByTagName("img")[0].src="/*initial url*/"; }; })(); </script> </head> <body> <img /> </body> </html> and of java (with problem) : package camba; import java.applet.Applet; import java.awt.Button; import java.awt.Graphics; import java.awt.Image; import java.awt.Label; import java.awt.Panel; import java.awt.TextField; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.net.URL; import java.security.Timestamp; import java.util.Date; import java.util.concurrent.TimeUnit; import java.util.concurrent.atomic.AtomicBoolean; import javax.imageio.ImageIO; public class Camba extends Applet implements ActionListener{ Image img; TextField textField; Label label; Button start,stop; boolean terminate = false; long viewTime; public void init(){ label = new Label("please enter camera URL "); add(label); textField = new TextField(30); add(textField); start = new Button("Start"); add(start); start.addActionListener(this); stop = new Button("Stop"); add(stop); stop.addActionListener(this); } public void actionPerformed(ActionEvent e){ Button source = (Button)e.getSource(); if(source.getLabel() == "Start"){ for (int i = 0; i < 7; i++) { myThread(50*i); } System.out.println("start..."); } if(source.getLabel() == "Stop"){ terminate = true; System.out.println("stop..."); } } public void paint(Graphics g) { update(g); } public void update(Graphics g){ try{ viewTime = System.currentTimeMillis(); g.drawImage(img, 100, 100, this); } catch(Exception e) { e.printStackTrace(); } } public void myThread(final int sleepTime){ new Thread(new Runnable() { public void run() { while(!terminate){ try { TimeUnit.MILLISECONDS.sleep(sleepTime); } catch (InterruptedException ex) { ex.printStackTrace(); } long requestTime= 0; Image tempImage = null; try { URL pic = null; requestTime= System.currentTimeMillis(); pic = new URL(getDocumentBase(), textField.getText()); tempImage = ImageIO.read(pic); } catch(Exception e) { e.printStackTrace(); } if(requestTime >= /*last view time*/viewTime){ img = tempImage; Camba.this.repaint(); } } }}).start(); System.out.println("thread started..."); } }

  Read the article

• bandwidth throttling C linux

  - by bob moch

  hi im currently creating a function to create a sleep time i can pause between packets for my port scanner im creating for personal/educational use for my home network. what im currently doing is opening /proc/net/dev and reading the 9th set of digits for the eth0 interface to find out the current packets being set and then reading it again and doing some math to figure out a delay to sleep between sending a packet to a port to identify it and fingerprint it. my problem is that no matter what throttle % i use it always seems to send the same rate of packets. i think its mainly my way of mathematically creating my sleep delay. edit:: dont mind the function declaration and the struct stuff all im doing is spawning this function in a thread and passing a pointer to a struct to the function, recreating the struct locally and then freeing the passed structs memory. void *bandwidthmonitor_cmd(void *param) { char cmdline[1024], *bytedata[19]; int i = 0, ii = 0; long long prevbytes = 0, currentbytes = 0, elapsedbytes = 0, byteusage = 0, maxthrottle = 0; command_struct bandwidth = *((command_struct *)param); free(param); //printf("speed: %d\n throttle: %d\n\n", UPLOAD_SPEED, bandwidth.throttle); maxthrottle = UPLOAD_SPEED * bandwidth.throttle / 100; //printf("max throttle:%lld\n", maxthrottle); FILE *f = fopen("/proc/net/dev", "r"); if(f != NULL) { while(1) { while(fgets(cmdline, sizeof(cmdline), f) != NULL) { cmdline[strlen(cmdline)] = '\0'; if(strncmp(cmdline, " eth0", 6) == 0) { bytedata[0] = strtok(cmdline, " "); while(bytedata[i] != NULL) { i++; bytedata[i] = strtok(NULL, " "); } bytedata[i + 1] = '\0'; currentbytes = atoi(bytedata[9]); } } i = 0; rewind(f); elapsedbytes = currentbytes - prevbytes; prevbytes = currentbytes; byteusage = 8 * (elapsedbytes / 1024); //printf("usage:%lld\n",byteusage); if(ii & 0x40) { SLEEP += (maxthrottle - byteusage) * -1.1;//-2.5; if(SLEEP < 0){ SLEEP = 0; } //printf("sleep:%d\n", SLEEP); } usleep(25000); ii++; } } return NULL; } SLEEP and UPLOAD_SPEED are global variables and UPLOAD_SPEED is in kb/s and generated via a speedtest function that gets the upload speed of my computer. this function is running inside a POSIX thread updating SLEEP which my threads doing the socket work grab to sleep by after every packet. as testing instead of only doing the ports i want to check i make it do all the ports over and over again so i can run dstat on a machine to check bandwidth and no matter what bandwidth.throttle is set to it always seems to generate the same amount of bandwidth to the dstat machine. the way i calculate how much i "should" throttle by is by finding the maximum throttle speed which is defined as maxthrottle = upload_speed * throttle / 100; for example if my upload speed was 1000kb/s and my throttle was 90 (90%) my max throttle would be 900kb/s from there it would find the current bytes sent from /proc/net/dev and then find my sleep time via incrementing or decrementing it via sleep += (maxthrottle - bytesysed) * -1.1; this should in theory increase or decrease the sleep time based on how many bytes used there are. the if(ii & 0x40) statement is just for some moderation control. it makes it so it only sets sleep to a new time every 30-40 iterations. final notes: the main problem is that the sleep timer does not seem to modify the speed of packets being set. or maybe its just my implementation because on a freshly restarted machine where /proc/net/dev has low numbers of bytes sent it seems to raise the sleep timer accordingly on my 60kb/s upload machine (ex if i set the throttle to 2 it will incline the sleep timer until network bandwidth out reaches the max bandwidth threshold, but when i try running it on a server which as been online forever it doesnt seem to work as nicely if at all. if anyone can suggest a new method of monitoring the network to adjust a sleep delay then let me know or if anyone sees a flaw in my code. thank you.

  Read the article

• SQLAuthority News – SQLPASS Nov 8-11, 2010-Seattle – An Alternative Look at Experience

  - by pinaldave

  I recently attended most prestigious SQL Server event SQLPASS between Nov 8-11, 2010 at Seattle. I have only one expression for the event - Best Summit Ever This year the summit was at its best. Instead of writing about my usual routine or the event, I am going to write about the interesting things I did and how I felt about it! Best Summit Ever Trip to Seattle! This was my second trip to Seattle this year and the journey is always long. Here is the travel stats on how long it takes to get to Seattle: 24 hours official air time 36 hours total travel time (connection waits and airport commute) Every time I travel to USA I gain a day and when I travel back to home, I lose a day. However, the total traveling time is around 3 days. The journey is long and very exhausting. However, it is all worth it when you’re attending an event like SQLPASS. Here are few things I carry when I travel for a long journey: Dry Snack packs – I like to have some good Indian Dry Snacks along with me in my backpack so I can have my own snack when I want Amazon Kindle – Loaded with 80+ books A physical book – This is usually a very easy to read book I do not watch movies on the plane and usually spend my time reading something quick and easy. If I can go to sleep, I go for it. I prefer to not to spend time in conversation with the guy sitting next to me because usually I end up listening to their biography, which I cannot blog about. Sheraton Seattle SQLPASS In any case, I love to go to Seattle as the city is great and has everything a brilliant metropolis has to offer. The new Light Train is extremely convenient, and I can take it directly from the airport to the city center. My hotel, the Sheraton, was only few meters (in the USA people count in blocks – 3 blocks) away from the train station. This time I saved USD 40 each round trip due to the Light Train. Sessions I attended! Well, I really wanted to attend most of the sessions but there was great dilemma of which ones to choose. There were many, many sessions to be attended and at any given time there was more than one good session being presented. I had decided to attend sessions in area performance tuning and I attended quite a few sessions this year, compared to what I was able to do last year. Here are few names of the speakers whose sessions I attended (please note, following great speakers are not listed in any order. I loved them and I enjoyed their sessions): Conor Cunningham Rushabh Mehta Buck Woody Brent Ozar Jonathan Kehayias Chris Leonard Bob Ward Grant Fritchey I had great fun attending their sessions. The sessions were meaningful and enlightening. It is hard to rate any session but I have found that the insights learned in Conor Cunningham’s sessions are the highlight of the PASS Summit. Rushabh Mehta at Keynote SQLPASS   Bucky Woody and Brent Ozar I always like the sessions where the speaker is much closer to the audience and has real world experience. I think speakers who have worked in the real world deliver the best content and most useful information. Sessions I did not like! Indeed there were few sessions I did not like it and I am not going to name them here. However, there were strong reasons I did not like their sessions, and here is why: Sessions were all theory and had no real world connections. All technical questions ended with confusing answers (lots of “I will get back to you on it,” “it depends,” “let us take this offline” and many more…) “I am God” kind of attitude in the speakers For example, I attended a session of one very well known speaker who is a specialist for one particular area. I was bit late for the session and was surprised to see that in a room that could hold 350 people there were only 30 attendees. After sitting there for 15 minutes, I realized why lots of people left. Very soon I found I preferred to stare out the window instead of listening to that particular speaker. One on One Talk! Many times people ask me what I really like about PASS. I always say the experience of meeting SQL legends and spending time with them one on one and LEARNING! Here is the quick list of the people I met during this event and spent more than 30 minutes with each of them talking about various subjects: Pinal Dave and Brad Shulz Pinal Dave and Rushabh Mehta Michael Coles and Pinal Dave Rushabh Mehta – It is always pleasure to meet with him. He is a man with lots of energy and a passion for community. He recently told me that he really wanted to turn PASS into resource for learning for every SQL Server Developer and Administrator in the world. I had great in-depth discussion regarding how a single person can contribute to a community. Michael Coles – I consider him my best friend. It is always fun to meet him. He is funny and very knowledgeable. I think there are very few people who are as expert as he is in encryption and spatial databases. Worth meeting him every single time. Glenn Berry – A real friend of everybody. He is very a simple person and very true to his heart. I think there is not a single person in whole community who does not like him. He is a friends of all and everybody likes him very much. I once again had time to sit with him and learn so much from him. As he is known as Dr. DMV, I can be his nurse in the area of DMV. Brad Schulz – I always wanted to meet him but never got chance until today. I had great time meeting him in person and we have spent considerable amount of time together discussing various T-SQL tricks and tips. I do not know where he comes up with all the different ideas but I enjoy reading his blog and sharing his wisdom with me. Jonathan Kehayias – He is drill sergeant in US army. If you get the impression that he is a giant with very strong personality – you are wrong. He is very kind and soft spoken DBA with strong performance tuning skills. I asked him how he has kept his two jobs separate and I got very good answer – just work hard and have passion for what you do. I attended his sessions and his presentation style is very unique.  I feel like he is speaking in a language I understand. Louis Davidson – I had never had a chance to sit with him and talk about technology before. He has so much wisdom and he is very kind. During the dinner, I had talked with him for long time and without hesitation he started to draw a schema for me on the menu. It was a wonderful experience to learn from a master at the dinner table. He explained to me the real and practical differences between third normal form and forth normal form. Honestly I did not know earlier, but now I do. Erland Sommarskog – This man needs no introduction, he is very well known and very clear in conveying his ideas. I learned a lot from him during the course of year. Every time I meet him, I learn something new and this time was no exception. Joe Webb – Joey is all about community and people, we had interesting conversation about community, MVP and how one can be helpful to community without losing passion for long time. It is always pleasant to talk to him and of course, I had fun time. Ross Mistry – I call him my brother many times because he indeed looks like my cousin. He provided me lots of insight of how one can write book and how he keeps his books simple to appeal to all the readers. A wonderful person and great friend. Ola Hallgren - I did not know he was coming to the summit. I had great time meeting him and had a wonderful conversation with him regarding his scripts and future community activities. Blythe Morrow – She used to be integrated part of SQL Server Community and PASS HQ. It was wonderful to meet her again and re-connect. She is wonderful person and I had a great time talking to her. Solid Quality Mentors – It is difficult to decide who to mention here. Instead of writing all the names, I am going to include a photo of our meeting. I had great fun meeting various members of our global branches. This year I was sitting with my Spanish speaking friends and had great fun as Javier Loria from Solid Quality translated lots of things for me. Party, Party and Parties Every evening there were various parties. I did attend almost all of them. Every party had different theme but the goal of all the parties the same – networking. Here are the few parties where I had lots of fun: Dell Reception Party Exhibitor Party Solid Quality Fun Party Red Gate Friends Party MVP Dinner Microsoft Party MVP Dinner Quest Party Gameworks PASS Party Volunteer Party at Garage Solid Quality Mentors (10 Members out of 120) They were all great networking opportunities and lots of fun. I really had great time meeting people at the various parties. There were few people everywhere – well, I will say I am among them – who hopped parties. NDA – Not Decided Agenda During the event there were few meetings marked “NDA.” Someone asked me “why are these things NDA?”  My response was simple: because they are not sure themselves. NDA stands for Not Decided Agenda. Toys, Giveaways and Luggage I admit, I was like child in Gameworks and was playing to win soft toys. I was doing it for my daughter. I must thank all of the people who gave me their cards to try my luck. I won 4 soft-toys for my daughter and it was fun. Also, thanks to Angel who did a final toy swap with me to get the desired toy for my daughter. I also collected ducks from Idera, as my daughter really loves them. Solid Quality Booth Each of the exhibitors was giving away something and I got so much stuff that my luggage got quite a bit bigger when I returned. Best Exhibitor Idera had SQLDoctor (a real magician and fun guy) to promote their new tool SQLDoctor. I really had a great time participating in the magic myself. At one point, the magician made my watch disappear.  I have seen better magic before, but this time it caught me unexpectedly and I was taken by surprise. I won many ducks again. The Common Question I heard the following common questions: I have seen you somewhere – who are you? – I am Pinal Dave. I did not know that Pinal is your first name and Dave is your last name, how do you pronounce your last name again? – Da-way How old are you? – I am as old as I can be. Are you an Indian because you look like one? – I did not answer this one. Where are you from? This question was usually asked after looking at my badge which says India. So did you really fly from India? – Yes, because I have seasickness so I do not prefer the sea journey. How long was the journey? – 24/36/12 (air travel time/total travel time/time zone difference) Why do you write on SQLAuthority.com? – Because I want to. I remember your daughter looks like you. – Is this even a question? Of course, she is daddy’s little girl. There were so many other questions, I will have to write another blog post about it. SQLPASS Again, Best Summit Ever! Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: About Me, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, SQLAuthority Author Visit, T SQL, Technology Tagged: SQLPASS

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112  | Next Page >