Search Results

Search found 17595 results on 704 pages for 'log in'.

Page 109/704 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

  • Force failover a Cisco ASA

    - by user974896
    I have two ASA in a lan state primary\secondary configuration. None of them have "failover active" or "no failover active" in their configuration. Would it be proper to failover in a manner such as: Log into console of primary unit and issue "failover lan state secondary", log into the console of the original secondary unit and issue "failover lan state primary". To fail back simply reverse the process or Log into the console of the primary unit and issue "no failover active", log into the console of the original secondary unit and issue "failover active". To fail back issue "failover active" on the original primary (now secondary) unit, and "no failover active" on the now primary unit. I do not like the second method because it adds configuration directives that were not in place before. Will the first method work?

    Read the article

  • Fortigate 200A firewall CPU high resource usage

    - by user119720
    This morning I'm receiving complaints from several end users that saying their whole department network are slow and have intermittent. Therefore I've checked our firewall to see whether if something goes wrong with the device.From my observation in the FortiGate dashboard status, the CPU resources is very high (99 percent). My first assumption is to clear the log since in the alert log the Fortigate log mention that it is already 90% full.Based on my understanding,the log can be cleared by restarting the firewall. After restarting the firewall the network seems okay again but then after several minutes it went up again.The condition still persist until now. Can someone show me where else I can check to fix this issue? I've really appreciate any help that I can get here.Thanks. Edit: diag sys top command

    Read the article

  • Installing nvidia drivers causes computer to boot to command prompt.

    - by levesque
    Hi, I have an Asus u30jc laptop, which comes with the Optimus prime graphics card switching technology that is now supported under 2.6.35, so I decided to give it a try. First I made sure the discrete graphics card was activated and then I installed the drivers proposed by the ubuntu software repository (nvidia-current). However, after rebooting all I got was a command prompt. My graphics card is a nvidia 310M. This is on Ubuntu 10.10 64 bits. What can I do to diagnose/identify the source of this problem? UPDATE: The messsages in my syslog tell me to check the xorg log: Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.053144 seconds Oct 11 12:42:59 u30jc-test gdm-simple-slave[1450]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.038176 seconds Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors Which I did. I found this message in my /var/log/Xorg.0.log : Fatal server error: [ 113.540] no screens found [ 113.540] What does that mean?

    Read the article

  • Can't update scala on Gentoo

    - by xhochy
    As I wanted to test Scala 2.9.2 on my gentoo system I tried updated the package but ended up with this error. I can't figure out where the problem may be: Calculating dependencies ...... done! >>> Verifying ebuild manifests >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Emerging (1 of 1) dev-lang/scala-2.9.2 >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Failed to emerge dev-lang/scala-2.9.2, Log file: >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log' >>> Jobs: 0 of 1 complete, 1 running Load avg: 0.23, 0.16, 0.20 >>> Jobs: 0 of 1 complete, 1 running, 1 failed Load avg: 0.23, 0.16, 0.20 >>> Jobs: 0 of 1 complete, 1 failed Load avg: 0.23, 0.16, 0.20 * Package: dev-lang/scala-2.9.2 * Repository: gentoo * Maintainer: [email protected] * USE: amd64 elibc_glibc kernel_linux multilib userland_GNU * FEATURES: sandbox [01m[31;06m!!! ERROR: Couldn't find suitable VM. Possible invalid dependency string. Due to jdk-with-com-sun requiring a target of 1.7 but the virtual machines constrained by virtual/jdk-1.6 and/or this package requiring virtual(s) jdk-with-com-sun[0m * Unable to determine VM for building from dependencies: NV_DEPEND: virtual/jdk:1.6 java-virtuals/jdk-with-com-sun !binary? ( dev-java/ant-contrib:0 ) app-arch/xz-utils >=dev-java/java-config-2.1.9-r1 source? ( app-arch/zip ) >=dev-java/ant-core-1.7.0 dev-java/ant-nodeps >=dev-java/javatoolkit-0.3.0-r2 >=dev-lang/python-2.4 * ERROR: dev-lang/scala-2.9.2 failed (setup phase): * Failed to determine VM for building. * * Call stack: * ebuild.sh, line 93: Called pkg_setup * scala-2.9.2.ebuild, line 43: Called java-pkg-2_pkg_setup * java-pkg-2.eclass, line 53: Called java-pkg_init * java-utils-2.eclass, line 2187: Called java-pkg_switch-vm * java-utils-2.eclass, line 2674: Called die * The specific snippet of code: * die "Failed to determine VM for building." * * If you need support, post the output of `emerge --info '=dev-lang/scala-2.9.2'`, * the complete build log and the output of `emerge -pqv '=dev-lang/scala-2.9.2'`. !!! When you file a bug report, please include the following information: GENTOO_VM= CLASSPATH="" JAVA_HOME="" JAVACFLAGS="" COMPILER="" and of course, the output of emerge --info * The complete build log is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log'. * The ebuild environment file is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/die.env'. * Working directory: '/var/tmp/portage/dev-lang/scala-2.9.2' * S: '/var/tmp/portage/dev-lang/scala-2.9.2/work/scala-2.9.2-sources' * Messages for package dev-lang/scala-2.9.2: * Unable to determine VM for building from dependencies: * ERROR: dev-lang/scala-2.9.2 failed (setup phase): * Failed to determine VM for building. * * Call stack: * ebuild.sh, line 93: Called pkg_setup * scala-2.9.2.ebuild, line 43: Called java-pkg-2_pkg_setup * java-pkg-2.eclass, line 53: Called java-pkg_init * java-utils-2.eclass, line 2187: Called java-pkg_switch-vm * java-utils-2.eclass, line 2674: Called die * The specific snippet of code: * die "Failed to determine VM for building." * * If you need support, post the output of `emerge --info '=dev-lang/scala-2.9.2'`, * the complete build log and the output of `emerge -pqv '=dev-lang/scala-2.9.2'`. * The complete build log is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/build.log'. * The ebuild environment file is located at '/var/tmp/portage/dev-lang/scala-2.9.2/temp/die.env'. * Working directory: '/var/tmp/portage/dev-lang/scala-2.9.2' * S: '/var/tmp/portage/dev-lang/scala-2.9.2/work/scala-2.9.2-sources' The following eix output may help: % eix java-virtuals/jdk-with-com-sun [I] java-virtuals/jdk-with-com-sun Available versions: 20111111 {{ELIBC="FreeBSD"}} Installed versions: 20111111(16:08:51 18/04/12)(ELIBC="-FreeBSD") Homepage: http://www.gentoo.org Description: Virtual ebuilds that require internal com.sun classes from a JDK Both virtual jdks 1.6 and 1.7 are installed: % eix virtual/jdk [I] virtual/jdk Available versions: (1.4) ~1.4.2-r1[1] (1.5) 1.5.0 ~1.5.0-r3[1] (1.6) 1.6.0 1.6.0-r1 (1.7) (~)1.7.0 Installed versions: 1.6.0-r1(1.6)(23:22:48 10/11/12) 1.7.0(1.7)(23:21:09 10/11/12) Description: Virtual for JDK [1] "java-overlay" /var/lib/layman/java-overlay

    Read the article

  • yum list installed including version of all installed packages CentOS 5.4

    - by Andy
    I have a list of packages installed with yum on CentOS 5.4 [root@server ~]# yum list installed ... Installed Packages GConf2.x86_64 2.14.0-9.el5 installed ImageMagick.x86_64 6.2.8.0-4.el5_1.1 installed MAKEDEV.x86_64 3.23-1.2 installed MySQL-python.x86_64 1.2.1-1 installed I would like to download these rpms locally using yumdownloader --resolve MySQL-python-1.2.1-1.x86_64 etc. However the package formatting is different (MySQL-python.x86_64 1.2.1-1 vs MySQL-python-1.2.1-1.x86_64) so I am unable to download them using the above command. I don't want to have to parse the output of yum list installed, and I also don't want to use the contents of /var/log/yum.log* as I'll have to account for erased packages and version discrepancies. However /var/log/yum.log* does have the formatting I require... May 25 14:58:15 Installed: groff-1.18.1.1-11.1.x86_64 May 25 14:58:15 Installed: bzip2-1.0.3-4.el5_2.x86_64 Any suggestions?

    Read the article

  • Logging another person off in Windows 7 using Task Manager

    - by BBlake
    Under WinXP, I could use Task Manager's Users tab to log off my wife's account which she always leaves logged in so I don't have to log in to her account and log it out. It's an older machine so I used that trick to free up every resource I could which might potentially slow down the game I'm playing at the time. I recently upgraded the machine to Win7 and when I try the same trick, I get an access denied popup. My logged in account does have Admin rights, so is it as simple as runing Task Manager "as an Administrator" in order to allow this? If so, how can I pull up Task Manager (other than the standard CTRL-ALT-DELETE) to have it pop up with Admin rights in order to log her account off in this manner?

    Read the article

  • SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

    - by Barkat Ullah
    Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

    Read the article

  • Drupal + Lighttpd: enabling clean urls (rewriting)

    - by Patrick
    I'm emulating Ubuntu on my mac, and I use it as a server. I've installed lighttpd + Drupal and the following configuration section requires a domain name in order to make clean urls to work. Since I'm using a local server I don't have a domain name and I was wondering how to make it work given the fact the ip of the local machine is usually changing. thanks $HTTP["host"] =~ "(^|\.)mywebsite\.com" { server.document-root = "/var/www/sites/mywebsite" server.errorlog = "/var/log/lighttpd/mywebsite/error.log" server.name = "mywebsite.com" accesslog.filename = "/var/log/lighttpd/mywebsite/access.log" include_shell "./drupal-lua-conf.sh mywebsite.com" url.access-deny += ( "~", ".inc", ".engine", ".install", ".info", ".module", ".sh", "sql", ".theme", ".tpl.php", ".xtmpl", "Entries", "Repository", "Root" ) # "Fix" for Drupal SA-2006-006, requires lighttpd 1.4.13 or above # Only serve .php files of the drupal base directory $HTTP["url"] =~ "^/.*/.*\.php$" { fastcgi.server = () url.access-deny = ("") } magnet.attract-physical-path-to = ("/etc/lighttpd/drupal-lua-scripts/p-.lua") }

    Read the article

  • Unable to access any ubuntu shares from android/windows clients

    - by dan
    I am running Ubuntu 11.04, and cant seem to access any of my shares. Here is the output from testparm-s : Load smb config files from /etc/samba/smb.conf rlimit_max: increasing rlimit_max (1024) to minimum Windows limit (16384) Processing section "[printers]" Processing section "[CanonMG2100AIO]" Processing section "[FreeAgent Drive]" Loaded services file OK. WARNING: You have some share names that are longer than 12 characters. These may not be accessible to some older clients. (Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.) Server role: ROLE_STANDALONE [global] server string = %h server (Samba, Ubuntu) encrypt passwords = No obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = Enter\snew\s\spassword:* %n\n Retype\snew\s\spassword:* %n\n password\supdated\ssuccessfully . username map = /etc/samba/smbusers unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 name resolve order = wins lmhosts host bcast dns proxy = No wins support = Yes usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d [printers] comment = All Printers path = /var/spool/samba create mask = 0700 guest ok = Yes printable = Yes browseable = No [CanonMG2100AIO] comment = Printer Drivers path = /var/lib/samba/printers read only = No guest ok = Yes [FreeAgent Drive] path = /media/FreeAgent Drive read only = No guest ok = Yes smbtree: Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER and hostname: dekstop I know the spelling of desktop is incorrect. it was a duh moment. Any help would be greatly appreciated.

    Read the article

  • How can I set up OpenVPN to accept more than 60 connections?

    - by Robin
    Greetings! We're using OpenVPN and today hit an unexpected connection limit of 60 - even though max-clients is set to the source code default 1024. Server log: Tue Dec 21 13:49:41 2010 MULTI: new incoming connection would exceed maximum number of clients (60) We're slowly adding new clients to the VPN and expect to hit 200 some time next year, if we can get it working. We're running the server on a Win2003 R2. OpenVPN 2.0.9 Server config as follows: local 192.168.10.211 port 1195 proto tcp dev tun dev-node OpenVPN_Vision ca vision_ca.crt cert vision_server.crt key vision_server.key # This file should be kept secret dh vision_dh1024.pem server 192.168.211.0 255.255.255.0 ifconfig-pool-persist vision_ipp.txt ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 ;client-to-client keepalive 10 120 comp-lzo ;max-clients 100 # Default in source code is 1024 persist-key persist-tun status openvpn-status-vision.log log vision.log verb 3 I would greatly appreciate any help or input on this one. Thanks! Best regards, Robin

    Read the article

  • SVN Authentication with LDAP and Active Directory

    - by Alex Holsgrove
    I am having a few problems getting SVN authentication to work with LDAP / Active Directory. My SVN installation works fine, but after enabling LDAP in my apache vhost, I just can't get my users to authenticate. I can use a selection of LDAP browsers to successfully connect to Active Directory, but just can't seem to get this to work. SVN is setup in /var/local/svn Server is svn.domain.local For testing, my repository is /var/local/svn/test My vhost file is as follows: <VirtualHost *:80> ServerAdmin [email protected] ServerAlias svn.domain.local ServerName svn.domain.local DocumentRoot /var/www/svn/ <Location /test> DAV svn #SVNListParentPath On SVNPath /var/local/svn/test AuthzSVNAccessFile /var/local/svn/svnaccess AuthzLDAPAuthoritative off AuthType Basic AuthName "SVN Server" AuthBasicProvider ldap AuthLDAPBindDN "CN=adminuser,OU=SBSAdmin Users,OU=Users,OU=MyBusiness,DC=domain,DC=local" AuthLDAPBindPassword "admin password" AuthLDAPURL "ldap://192.168.1.6:389/OU=SBSUsers,OU=Users,OU=MyBusiness,DC=domain,DC=local?sAMAccountName?sub?(objectClass=*)" Require valid-user </Location> CustomLog /var/log/apache2/svn/access.log combined ErrorLog /var/log/apache2/svn/error.log </VirtualHost> In my error.log, I don't seem to get any bind errors (should I be looking elsewhere?), but just the following: [Thu Jun 21 09:51:38 2012] [error] [client 192.168.1.142] user alex: authentication failure for "/test/": Password Mismatch, referer: http://svn.domain.local/test/ At the end of "AuthLDAPURL", I have seen people using TLS and NONE but neither seem to help in my case. I have the ldap modules loaded and have checked as much as I know, so any help would be most welcome. Thanks

    Read the article

  • Ubuntu: move logs from /dev/tty8 to different terminal /dev/tty12 or get rid of it.

    - by Casual Coder
    I want to know how to move or get rid of /dev/tty8 log output in Ubuntu 9.10. /dev/tty7 is my regular X session. When I am switching user to test account where I can try and test setups and configs I am at next available console i.e. /dev/tty9 because /dev/tty8 is taken by log output. Where can I configure this ? All I've found related to /dev/tty8 is commented lines in /etc/rsyslog.d/50-default.conf. I changed it like that: daemon,mail.*;\ news.=crit;news.=err;news.=notice;\ *.=debug;*.=info;\ *.=notice;*.=warn /dev/tty12 And I've got nice log output on /dev/tty12 but where is configuration for log output on /dev/tty8. How can I change it?

    Read the article

  • Is this a dual monitor reset bug?

    - by Tentresh
    My two displays are: Intel GMA x4500 Laptop (1280x800 native resolution of the built-in display) External display (1920x1080) A few minutes after I login to my dual monitor setup, it gets reset to mirror screens. If I restore the settings via the displays application, everything is fine. On each reset, the following messages are written into /var/log/Xorg.0.log: [ 60.852] (II) PM Event received: Capability Changed [ 60.852] I830PMEvent: Capability change [ 132.920] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 132.920] (II) intel(0): Printing DDC gathered Modelines: [ 132.920] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 134.228] (II) intel(0): Allocated new frame buffer 1280x800 stride 5120, tiled Whereas right on startup or manual resolution reset, /var/log/Xorg.0.log reports the expected frame buffer allocation: [ 1562.382] (II) intel(0): EDID vendor "SEC", prod id 12869 [ 1562.382] (II) intel(0): Printing DDC gathered Modelines: [ 1562.382] (II) intel(0): Modeline "1280x800"x0.0 68.94 1280 1296 1344 1408 800 801 804 816 -hsync -vsync (49.0 kHz) [ 1576.740] (II) intel(0): Allocated new frame buffer 3200x1080 stride 12800, tiled Is Ubuntu 12.04 not compatible with my video card? Can this be solved within Ubuntu? I like its interface, but manually fiddling with resolution on every login is not bearable.

    Read the article

  • Windows Network File Transfer to Samba server: “Are you sure you want to copy this file without its properties?”

    - by jimp
    I am transferring a lot of files to a new NAS based on OpenMediaVault, with the Samba 3.5.6 service running. I am transferring from Windows 7 64-bit to the NAS, and on some media files Windows is prompting about losing some property data across the transfer. I have never seen this before when transferring to Samba boxes I have built myself (vs this turnkey solution), so I'm guessing there must be a Samba setting I can change to preserve the file properties in question instead of permanently losing whatever they contain (Date Taken? Exposure? Flash Fired? etc). Or maybe I've just never encountered this before; I'm really not sure. I tried adding ea support = yes and store dos attributes = yes to the [global] section, but the problem remains. The Linux file system is ext4 mounted with user_xattr (full options: defaults,acl,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0) as Samba requires. Any ideas would be greatly appreciated. Thank you! Samba config: [global] workgroup = WORKGROUP server string = %h server include = /etc/samba/dhcp.conf dns proxy = no log level = 2 syslog = 2 log file = /var/log/samba/log.%m max log size = 1000 syslog only = yes panic action = /usr/share/samba/panic-action %d encrypt passwords = true passdb backend = tdbsam obey pam restrictions = yes unix password sync = no passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . pam password change = yes socket options = TCP_NODELAY IPTOS_LOWDELAY guest account = nobody load printers = no disable spoolss = yes printing = bsd printcap name = /dev/null unix extensions = yes wide links = no create mask = 0777 directory mask = 0777 use sendfile = no null passwords = no local master = yes time server = yes wins support = yes ea support = yes store dos attributes = yes Note: I found this related question, but it explains the loss due to the user trying to transfer from NTFS to FAT32.

    Read the article

  • hosting 2 webapps under 1 apache/tomcat

    - by mkoryak
    I am trying to host multiple webapps under tomcat 6 behind apache2 via mod_jk. I am at my wits end with this. the problem i am facing that both domains seems to point to a single tomcat 'domain'. my server.xml looks like this: <Service name="Catalina"> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" URIEncoding="UTF-8" redirectPort="8443" /> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" /> <Connector port="8010" protocol="AJP/1.3" redirectPort="8443" /> <Engine name="Catalina" defaultHost="dogself.com"> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <Host name="dogself.com" appBase="webapps-dogself" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Host> <Host name="natashacarter.com" appBase="webapps-natashacarter.com" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> </Host> </Engine> </Service> my workers.properties looks like this: worker.list=dogself,natashacarter worker.dogself.port=8009 worker.dogself.host=dogself.com worker.dogself.type=ajp13 worker.natashacarter.port=8010 worker.natashacarter.host=natashacarter.com worker.natashacarter.type=ajp13 finally my apache vhosts look like this: <VirtualHost 69.164.218.75:80> ServerName dogself.com DocumentRoot /srv/www/dogself.com/public_html/ ErrorLog /srv/www/dogself.com/logs/error.log CustomLog /srv/www/dogself.com/logs/access.log combined JkMount /* dogself </VirtualHost> and <VirtualHost 69.164.218.75:80> ServerName natashacarter.com DocumentRoot /srv/www/dogself.com/public_html/ ErrorLog /srv/www/dogself.com/logs/error.log CustomLog /srv/www/dogself.com/logs/access.log combined JkMount /* natashacarter </VirtualHost> when i log into manager webapp on both dogself.com and natashacarter.com, i can deploy to a context path on dogself, and that same contextpath will appear on natashacarter - so i know for a fact that this is the same tomcat domain. edit: just found this in my mod_jk log [Sun Feb 20 21:15:43 2011] [28546:3075521168] [warn] map_uri_to_worker_ext::jk_uri_worker_map.c (962): Uri * is invalid. Uri must start with / [Sun Feb 20 21:16:44 2011] [28548:3075521168] [info] ajp_send_request::jk_ajp_common.c (1496): (dogself) all endpoints are disconnected, detected by connect check (1), cping (0), send (0) but not sure why dogself wouldnt respond please help a brother out

    Read the article

  • After closing the ssh terminal, the thin server is down

    - by Keating Wang
    I have a rails project run on the thin server(1.3.1) on a ubuntu server. I ssh to the server and start thin with command 'thin start -C config/thin.yml', following the thin.yml, port: 3000 log: log/thin.log timeout: 30 chdir: /home/byht/56platform/dev/tracker environment: production servers: 1 daemonize: true After thin starts successfully, I visit the project and it works well. Then, I close the terminal, I can also visit the pages that have been visited, but when I visit the pages that not been visited before closing ssh terminal, a "500" error appears on the page. I didn't find the error messages in the log file. I have tried start thin with nohup and sudo, but they are useless. I sign in the ubuntu server locally, then the problem disappears. But I need sign in the server to stat thin with ssh when I'm home.

    Read the article

  • Ubuntu 12.04 crash analysis - strange binary data on all open files at the moment of crash

    - by lanbo
    A couple of hours ago we got a system crash on Ubuntu 12.04. We checked all the log files and there is nothing suspicious to blame to. Last stuff that was logged was some dovecot activity. There are no kernel panic messages. Nothing. It is a new server (new hardware) we are testing before production. And because it is new hard, I'm suspicious the problem may be due to some faulty hardware. We already run memtester with no problem detected. I'll be happy to hear from other hardware testing tools (the machine has SSD). Anyway, the thing I wanted to ask you is a different one. The strange thing is on every open file at the moment of the crash we found the next sequence of symbols was written into them: "@^@^@^@^@^@^@...". For example, on the syslog log file we got: Apr 16 15:53:56 odyssey dovecot: pop3-login: Aborted login (auth failed, 1 attempts): user=<info>, method=PLAIN, rip=46.29.255.73, lip=5.9.58.177 ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^ [these continues for about 1000 chars...] ^@^@^@^@Apr 16 15:55:12 odyssey kernel: imklog 5.8.6, log source = /proc/kmsg started. We got all these symbols in all open files. These include: syslog, mail.log, kern.log, ... But also on some logs that are output by php scripts run in CRONs from user accounts (not root). So, any idea why all open files got these characters written during the crash? This is pretty bad since the crash corrupted many files (we don't even know which other ones may be affected). We are suspicious that all open files (in write mode maybe) at the moment of the crash got all these symbols inserted. Why is that? BTW [in case it helps], the system automatically rebooted after the crash but Apache did not start. There were not traces in /var/apache2/*log why apache did not start. After running a "service apache2 start" it started with no problems. Also, we rebooted the machine manually and Apache also started on reboot. But it did not start after the crash and no errors were reported. Thanks guys!

    Read the article

  • Rsync plugin to many local wordpress installs via script or cli

    - by Nick Abbey
    I am maintaining a large number of wordpress installs on a production server, and we are looking to deploy InfiniteWP for managing these installs. I am looking for a way to script the distribution of the plugin folder to all of these installs. On server wp-prod, all sites are stored in /srv//site/ The plugin needs to be copied from ~/iws-plugin to /srv//site/wp-content/plugins/ Here's some pseudo code to explain what I need to do: array dirs = <all folders in /srv> for each d in dirs if exits "/srv/d/site/wp-content/plugins" rsync -avzh --log-file=~/d.log ~/plugin_base_folder /srv/d/site/wp-content/plugins/ else touch d.log echo 'plugin folder for "d" not found' >> ~/d.log end end I just don't know how to make it happen from the cli or via bash. I can (and will) tinker with a bash or ruby script on my test server, but I'm thinking the command-line-fu here on SF is strong enough to handle this issue much more quickly than I can hack together a solution. Thanks!

    Read the article

  • mysqld refusing connections from localhost

    - by Dennis Rardin
    My mail server (Ubuntu 10.04) uses mysql for virtual domains, virtual users. For some reason, mysqld has started refusing connections from localhost. I see these in the mail server log: Oct 6 00:31:14 apollo postfix/trivial-rewrite[16888]: fatal: proxy:mysql:/etc/postfix/mysql-virtual_domains.cf(0,lock|fold_fix): table lookup problem and: Oct 7 13:39:15 apollo postfix/proxymap[25839]: warning: connect to mysql server 127.0.0.1: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I also get the following in auth.log: Oct 6 22:33:31 apollo mysqld[31775]: refused connect from 127.0.0.1 Telnet to the local port: root@apollo:/var/log/mysql# telnet localhost 3306 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. Connection closed by foreign host. root@apollo:/var/log/mysql# I am not sure why this started happening, but there was a disk failure in a RAID 1 pair a bit earlier that day. So it's possible I have a damaged config file or something. But mail was working for at least an hour after the drive event, so who knows for sure? phpmyadmin works fine, and the databases themselves look like they're intact. I think/believe that selinux and iptables are disabled and not running. So ... why is mysqld refusing connections from localhost? What should I check? What processes might cause this if a .conf file or possibly a binary was damaged? Which other log files might contain clues? I've enabled "general logging" in /etc/mysql/my.cnf, but I get no interesting or informative entries there. Thanks, m00tpoint

    Read the article

  • syslog ip ranges to specific files using `rsyslog`

    - by Mike Pennington
    I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

    Read the article

  • long access times and errors in iis application

    - by Jens Olsson
    Hi, I am having an issue with an IIS application (details of environment at the end of the message). The web site works great most of the time and I cannot reproduce any error in our test system. On the live system however with on averare of 5-15 requests per second I have a problem with that some requests (about 0.05%) will take over 300 seconds to complete. The other requests complete withing 5-10 seconds. It seem like if all the errornous requests end up with a Timer_EntityBody error in the error log. I have never seen this as an end user but I guess that they will receive some kind of error message. I am trying to find out what can be causing this errornous behaviour. Any ideas are welcome. I have read something about that there can be an MTU issue if ICMP and MTU protocols are blocked in the firewall. Does that sound reasonable? I have also read about updating to IIS 7 should do the trick. Does it sound reasonable? I think that the problem has another cause but I have no idea of what. I have tried running hte perormance monitor, monitoring for database locks and active transaction counts. I can see some of these in the perfmon log for the MSSQL server (another machine) for example: Active transactions is sometimes peaking and sometimes for long periods Lock waits per seconds is sometimes peaking Transactions per second is sometimes peaking Page IO Latch wait is sometimes peaking Lock wait time (ms) is sometimes peaking But I cannot see that any of these correlate to the errors in the IIS error log. On the IIS server machine I can also see with perfmon that some values peak a few times during a day: Request execution time Avg disk queue length I can neither see that any of these correlate to the errors in the IIS error log. In the below code I have anonymized by replacing some parts with HIDDEN The following can be seen in the access log 2010-10-01 08:35:05 W3SVC1301873091 **HIDDEN** POST /**HIDDEN**/Modules/BalanceModule.aspx - 80 - **HIDDEN** Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+5.1;+.NET+CLR+2.0.50727;+.NET+CLR+3.0.4506.2152;+.NET+CLR+3.5.30729;+.NET4.0C;+.NET4.0E) ASP.NET_SessionId=**HIDDEN** 400 0 64 0 2241 127799 At the same time the following can be seen in the error log: 2010-10-01 08:35:05 **HIDDEN** 1999 **HIDDEN** 80 HTTP/1.0 POST /**HIDDEN**/Modules/BalanceModule.aspx - 1301873091 Timer_EntityBody Test+Pool I can tell the following about the environment: Server: Windows Server 2003 x64 SP2 running on VMWare HTTP Server: IIS v6.0 with ASP.NET 2.0.50727 Antivirus: Trend Micro OfficeScan (Is it a good idea to have this on a server?)

    Read the article

  • Immediate logout after login with PAM, Kerberos, and LDAP

    - by Dylan Klomparens
    I've set up remote login on a computer using Kerberos and LDAP. I've also configured NFS to mount onto /home so that the user's home directory is the same wherever they login. Kerberos authentication seems to work fine. I can get a ticket using kinit user1 (assuming user1 is a remote user) and see the ticket with klist. I'm pretty sure LDAP is working because I see the proper output from getent passwd, which lists all the remote users. The contents of /home are present when I list the files. The problem is: when I try to login as a remote user the session is immediately ended. Why is it not letting me stay logged in? Here is the output from /var/log/messages after a login attempt: # /var/log/messages: Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: authentication succeeds for 'user1' ([email protected]) Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (establish credential) called Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (delete credential) called EDIT: The distro is openSUSE. Here are the common-* files in /etc/pam.d:   # /etc/pam.d/common-account account required pam_unix.so   # /etc/pam.d/common-auth auth sufficient pam_krb5.so minimum_uid=1000 auth required pam_unix.so nullok_secure try_first_pass   # /etc/pam.d/common-session session optional pam_umask.so umask=002 session sufficient pam_krb5.so minimum_uid=1000 session required pam_unix.so There doesn't appear to be a /var/log/auth.log file nor a /var/log/secure file.

    Read the article

  • DDNS Not Creating Journal (Dhcpd and Named)

    - by user130094
    * EDIT 1 * After monkeying with additional debug logging I see some log entries of interest. 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: journal rollforward failed: no more 27-Jul-2012 23:45:26.537 general: error: zone example.lan/IN/internal: not loaded due to errors. ^^^ If I can remedy the above messages I think I'll be good to go ^^^ * EDIT 2 * Grasping at straws I touched a forward and a reverse zone journal file and restarted named. Boom! Works. Despite documentation stating the files are created automatically and what I have seen before... dunno why but that did the trick. Also re-checked perms on the dir the files live in. As certain as I was, they were correct with named having rw. CentOS 6 (final) dhcpd 4.1.1-P1 named BIND 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 Basic DHCP and DNS functionality are in place on 192.168.111.2. Clients are assigned addresses as intended and can resolve local DNS names as well as Internet names. My problem is that named's zone journal files are not created. chroot: /var/named/chroot I tried placing the zone files in various directories (/var/named/data, /var/named, /var/named/dynamic - no matter which dir with named owning and wide open perms I now get nowhere). Along the way I, at one point, got a permission denied when named tried to create the journal. Resolved the issue by: chown --recursive named:named /var/named chmod --recursive 777 /var/named The journal was then created and here's where things fell apart. I attempted to tame permissions to something more sane and broke it. Once changed and having restarted named it threw an error indicating the journal was out of sync (or something to that affect)... didn't matter since this is a new setup so I deleted it and now it is not recreated. Now though I see no errors in /var/log/messages, my chrooted /var/log/named.log, or chrooted /var/log/named.debug. I increased the debug level with 'rndc trace' - no love. Increased trace to 10, still nothing. SELinux is disabled... [root@server temp]# sestatus SELinux status: disabled dhcpd.conf... allow client-updates; ddns-update-style interim; subnet 192.168.111.0 netmask 255.255.255.224 { ... key dhcpudpate { algorithm hmac-md5; secret LDJMdPdEZED+/nN/AGO9ZA==; } zone example.lan. { primary 192.168.111.2; key dhcpudpate; } } named.conf... key dhcpudpate { algorithm hmac-md5; secret "LDJMdPdEZED+/nN/AGO9ZA=="; }; zone "example.lan" { type master; file "/var/named/dynamic/example.lan.db"; allow-transfer { none; }; allow-update { key dhcpudpate; }; notify false; check-names ignore; }; The following shows /var/log/named.log output of named starting up - no errors. 27-Jul-2012 21:33:39.349 general: info: zone 111.168.192.in-addr.arpa/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.349 general: info: zone example.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example2.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.350 general: info: zone example3.lan/IN/internal: loaded serial 2012072601 27-Jul-2012 21:33:39.350 general: info: zone example4.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: zone example5.lan/IN/internal: loaded serial 2012072501 27-Jul-2012 21:33:39.351 general: info: managed-keys-zone ./IN/internal: loaded serial 0 27-Jul-2012 21:33:39.351 general: info: zone example.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example1.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example2.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.352 general: info: zone example3.lan/IN/external: loaded serial 2012072501 27-Jul-2012 21:33:39.353 general: info: managed-keys-zone ./IN/external: loaded serial 0 27-Jul-2012 21:33:39.353 general: notice: running 27-Jul-2012 21:34:03.825 general: info: received control channel command 'trace 10' 27-Jul-2012 21:34:03.825 general: info: debug level is now 10 ...and /var/log/messages for a named start... Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: BIND 9 is maintained by Internet Systems Consortium, Jul 27 23:02:04 server named[9124]: Inc. (ISC), a non-profit 501(c)(3) public-benefit Jul 27 23:02:04 server named[9124]: corporation. Support and training for BIND 9 are Jul 27 23:02:04 server named[9124]: available at https://www.isc.org/support Jul 27 23:02:04 server named[9124]: ---------------------------------------------------- Jul 27 23:02:04 server named[9124]: adjusted limit on open files from 4096 to 1048576 Jul 27 23:02:04 server named[9124]: found 2 CPUs, using 2 worker threads Jul 27 23:02:04 server named[9124]: using up to 4096 sockets Jul 27 23:02:04 server named[9124]: loading configuration from '/etc/named.conf' Jul 27 23:02:04 server named[9124]: using default UDP/IPv4 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: using default UDP/IPv6 port range: [1024, 65535] Jul 27 23:02:04 server named[9124]: listening on IPv4 interface eth0, 192.168.111.2#53 Jul 27 23:02:04 server named[9124]: generating session key for dynamic DNS Jul 27 23:02:04 server named[9124]: sizing zone task pool based on 12 zones Jul 27 23:02:04 server named[9124]: set up managed keys zone for view internal, file 'dynamic/3bed2cb3a3acf7b6a8ef408420cc682d5520e26976d354254f528c965612054f.mkeys' Jul 27 23:02:04 server named[9124]: set up managed keys zone for view external, file 'dynamic/3c4623849a49a53911c4a3e48d8cead8a1858960bccdea7a1b978d73ec2f06d7.mkeys' Jul 27 23:02:04 server named[9124]: command channel listening on 127.0.0.1#953 What can I do to troubleshoot this further? It almost seems as though dhcpd is not triggering the update. Maybe I should troubleshoot here and, if so, how? Many thanks.

    Read the article

  • How to set up mysql storage for certain rsyslog input matches?

    - by ylluminate
    I'm draining various logs from Heroku to an rsyslog linux (ubuntu) server and am starting to have a little more to bite off than I can chew in terms of working with my log histories. I am needing to be able drill back in time based on more flexible details and more flexible access than what the standard syslog file(s) provide. I'm thinking that logging to mysql may be the correct approach, but how do I set this up such that it pulls only certain log entries into a table based on an identified? For example, I see a long hex string identifying each log entry from a certain Heroku app instance. I assume that I can just pipe those into the mysql socket vs ALL rsyslog input into mysql... Could someone please direct me to a resource that can walk me through the process of setting something like this up or simply provide some details that can help? I have 15+ years of Unix experience so I just need some nudging in the right direction as I've not really done a tremendous amount of work with syslog daemons previously in terms of pooling various servers into one. Additionally, I'd be interested in any log review tools that could make drilling through log arrangements like this more handy for developers.

    Read the article

  • Trouble WIth Immediate Shutdown in Ubuntu 13.10 with Cinnamon

    - by Sneha429
    Just installed Ubuntu on my family's computer. I thought the Cinnamon desktop environment would be better for my parents who have only ever used Windows. Everything works great until I try to shut down. Shutting down while in Cinnamon desktop brings up a prompt window that says it will shutdown in 60 seconds and gives the option to either suspend or cancel. The suspend button does not suspend the computer. Allowing the timer to countdown merely logs the current user out. Under power management, I have selected Shutdown Immediately for Power button action. I still get the same prompt. I have tried toggling between the other options, but regardless of what option is selected, the shutdown button always brings up the suspend or cancel prompt with no way to shutdown immediately. I would prefer not to use the power button for this as it is partially concealed with the computer desk. The fastest way to shutdown is to log out (which says it will log out in 60 seconds but also has log out and cancel buttons, so I can immediately log out) and then shutdown. I would prefer to have it automatically shut down. Any and all suggestions are appreciated. Thank you!

    Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >