Search Results

Search found 2602 results on 105 pages for 'dell vostro'.

Page 11/105 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Dell Dimension 2400 problem

  - by murgatroid99

  I have a new problem with a Dell Dimension 2400 PC. Until yesterday or the day before, it was working fine, but today when I press the power button the light on the power button turns yellow instead of green, the fan behind the processor increases speed until it sounds like a jet engine, and the computer does not boot up. I cleaned out the dust in the computer so that is not the problem. Also, the fan was blowing cold air. Do any of you know what might be causing this and how I might be able to fix it?

  Read the article

• Very slow disk performance on Dell PowerEdge 2950 w/ PERC 6/i running RAID 10

  - by vocoder

  I recently set up a server running Ubuntu 10.04 LTS on a Dell PowerEdge 2950 server - it has 6 500 gb 7200RPM SATA drives setup in a RAID 10 config. I am seeing extremely poor disk performance - the RAID array reports all disks are normal and using MegaCLI, it looks like the BBU is fine. hdparm -tT /dev/sda reports: Timing cached reads: 90 MB in 2.05 seconds = 43.96 MB/sec Timing buffered disk reads: 24 MB in 3.11 seconds = 7.72 MB/sec So as you can see, it takes forever to something as simple as an apt-get upgrade and even logging into the server. How do I go about troubleshooting what is causing this? I upgraded the firmware on the PERC 6i RAID controller to the latest, but didn't see any improvements.

  Read the article

• Getting packets from one port to another on a Dell PowerConnect 2824 switch

  - by Arvo Bowen

  I have a dell PowerConnect 2824 and I have a cat 5 cable connected from port 1 to port 23. Port 1 is reserved for VLAN 1 (the only VLAN that can manage the switch) and port 18-23 belong to VLAN 112. I currently have the switch setup with ip 10.71.3.5/27 and a test machine plugged into port 22 with IP address 10.71.3.30/27. For some reason I can not ping 10.71.3.5 from my test machine (10.71.3.30). Note: When I try to ping the server plugged into port 21 (IP: 10.71.3.7/27) also VLAN 112, I get responses just fine. Note: When I plug my test machine directly into port 1, I can ping 10.71.3.5 just fine. Quick Recap: Switch IP: 10.71.3.5 Port 1 - dedicated to management - (VLAN1) Port 21 - SERVER (10.71.3.7/27) - (VLAN112) Port 22 - test machine (10.71.3.30/27) - (VLAN112) Port 23 - dedicated to management (to hop over to VLAN 1 from VLAN 112) - (VLAN112)

  Read the article

• How to set up Dell OMSA tools on Debian 6 (Squeeze) (PE2950)

  - by javano

  I assume I have set up them up incorrectly or am missing a library or dependency. When I log into the OMSA web interface I can't see anything Also, omreport tells me nothing; root@box:~# omreport storage controller No controllers found I assume these two will use the same source of information so what ever is wrong will fix them both. I set up OMSA as per these instructions. Also I have compiled MegaCLI (as this is a PowerEdge 2950 with a Perc 6/i controller) and I have used that to update the RAID firmware, so that works, but the Dell tools aren't. What have I missed during set up? root@kvm1:~# cat /etc/issue Debian GNU/Linux 6.0 \n \l root@kvm1:~# uname -a Linux kvm1.mivoice.cust.vostron.net 3.4.9 #1 SMP Wed Aug 22 19:08:46 BST 2012 x86_64 GNU/Linux

  Read the article

• Removing RAID on a DELL power-edge server

  - by Simon Callan

  We have a Dell Power-edge T110 server, with either a PERC S100 or S300 raid controller (I suspect S100), and 2 x 500GB SATA hard discs. These discs are running in RAID-1 configuration, (either 1 or 2 virtual discs), and on top of this, we have the C and D drives. As we are running low on disc space, we are looking at dropping the RAID to get some disc space back. Is it possible to split the discs back into 2 seperate hards discs that the OS can see, without losing all the data on the drives? Even better, would it be possible to split the D: drive, leaving the OS C: drive in RAID1 configuration?

  Read the article

• Dell poweredge 1850's - wont install os

  - by user1326789

  I have 3 of these dell 1850 rack servers. 1 has 3GB RAM and 2 73GB HDD's. 2 have 6GB RAM and each of them has 2 73GB HDD's. I am currently trying to install an os on them but when i boot with windows xp setup, it gives me an error saying no partition found. Now i have set these drives up in RAID on the server and i put them "online" so it should be working fine but they're not. Please assist me in installing an operating system on these, i have no clue as to if it's the BIOS or the RAID controller within it. Thanks in advance, -Matt.

  Read the article

• Installing W2K8 R2 on a Dell Poweredge 2850

  - by DerekT

  I'm a server novice and have been given a Dell 2850 (PERC 4e/Di). It has 3 blank HDs that I think are configured as RAID 5. I am trying to install W2K8 R2 SP1 on it. It doesn't have a DVD reader so I created an install USB. This works fine until it's time to copy files to the HD. It can't see a HD. There is an option to browse for drivers at this stage. Any idea what drivers I need and where to download them? I downloaded this driver RAID_DRVR_WIN_R227150.EXE but this failed with invalid signature. Thanks to dyasny for the link to LSI-LOGIC_MULTI-DEVICE_A00_R227150.exe.

  Read the article

• Dell U271 monitor DisplayPort suddenly not working

  - by Amir Latif

  My new(ish) Dell U271 took a bit of a knock and it now suddenly doesn't recognise the Macbook plugged into it via DisplayPort - this had been working great for several months up until now. When I "Scan Sources", it doesn't find anything on DisplayPort. However, one suspicious behaviour leads me to think all might not be lost. When the Mac is woken from sleep, this used to kick the monitor in (as an monitor would) and while it no longer does that, the light on the monitor does go from standby orange to blue briefly, then the monitor says it's going into "power save" mode. It seems like it gets some kinda signal. Any ideas on how I can diagnose the problem? I'm trying to find another mac but no one near me has one ...

  Read the article

• Dell 620 display is too bright to use

  - by keith

  I have a Dell D620 with a display problem. In windows 7 the display seems to be too bright, the text is broken up, the only way to see the mouse is at a very oblique angle. Changing the brightness with fn and brightness control has little/no effect. When I put it in high contrast mode I can see all the colors, but any windows pictures etc are still useless. I cannot get it to connect to an external monitor via VGA port or via a USB-VGA connector.

  Read the article

• Dell EqualLogic vs. EMC VNXe [closed]

  - by Untalented

  We've been looking into SMB SANs and based on the competitive pricing I've been getting we're really liking these two array's. There are some pro's to both solutions, but I've unable to really decide which to choose. The EMC offers better expandability since you can buy an additional shelf (roughly $1200) and can add drives then to the array. However, the Dell unit is still very nice. Can anyone comment on their experiences with the two and thoughts on this? Also, to get the VMware Storage API support you need VMware Enterprise. How much additional performance does this provide? It's roughly $15k more than the Essentials Plus bundle we're looking at (this is a small environment [3 Hosts 1 Array].

  Read the article

• Dell Studio XPS 16 Runs Hot

  - by dtbarne

  Specs: 1920x1080 i7 1.6 GHz quad core 6GB RAM 1GB ATI Radeon HD 6570M/5700 Series 500GB 7200rpm Hard Drive Love this laptop for many reasons, but it constantly runs hot (CPU is low 70s with basic tasks and often 80+ is not uncommon) and I'm finding it too much to deal with. The laptop feels very hot (almost too hot for a lap) and often gets so hot that the OS slows down or freezes altogether. I've tried cleaning it out and even replacing the thermal paste. I often use an external cooler, but it only helps 3-5 degrees and it's a pain to have to use. I've come to the conclusion that it just runs hot. I have two questions: What is to blame? The i7 processor, the gfx card, or is it just that this laptop has poor cooling? Does the Dell XPS 15 run cooler? I'm looking at replacing my current laptop, but I don't want to run into the same problem.

  Read the article

• Dell docking station / Windows 7 not detecting HannsG JC199D via DVI

  - by user27150

  I have a laptop running Win7 that I use with a Dell docking station. I'd used it with XP for a couple years running dual monitors from the docking station, one from the VGA and one from the DVI. After upgrading to Win7, the monitor that's on the DVI out is not detected, using "rigorous detection" or otherwise. I've switched the cables to verify that it's not the monitor at fault-- but I can't find any info on why the monitor wouldn't be detected. I've got the latest and greatest Nvidia drivers installed (at least, as far as Windows update is aware). Leaving the laptop lid partly open does allow Windows to detect the laptop's native screen as well as the VGA monitor, but never the DVI. The monitors are HannsG JC199Ds. Any ideas? Thanks!

  Read the article

• Remote RAID Control in ESXi on a Dell PowerEdge 2950 Using OpenManage

  - by yoyomommy

  I was wondering how one can add a drive into an existing RAID array while ESXi is still running. I have read that you are able to use Dell OpenManage to do this. I have installed OMSA 7.0 on the VMWare ESXi host (5.0 and fully updated) and I've installed OpenManage Essentials on a Windows Server 2008 R2 guest. The issue that I'm having is that OpenManage is unable to see my RAID controller. I have seen videos and photos as parts of guides on how to do this online, so I would assume that the functionality exists and I just have it set up wrong.

  Read the article

• Connect Lenovo Thinkpad Edge e120 to WQHD display (such as Dell U2711) through HDMI

  - by Fulvio

  On paper, the HDMI version of the Lenovo Thinkpad Edge e120 is 1.3, which supports WQHD. Does it actually work? I want to connect the e120 to a WQHD display, such as the Dell U2711 or an Apple Cinema Display. I run Windows 7 Ultimate and latest drivers. The e120 I think has the Intel HD Graphics 3000 onboard chipset. I don't have the chance to test out the e120 with neither of these displays, so I'm seeking for an opinion from those who have tried. Thank you

  Read the article

• Dell XPS 710 - Boot Device Not Available

  - by WilliamKF

  Recently I was gifted a Dell XPS 710 tower running WinXP SP3. It was running fine until today when I restarted and received a blue screen and the error "unmountable boot volume". In order to fix this issue I've attempted to boot from the Windows XP CD and run chkdsk. However when I attempt to boot from the CD drive I get a "Boot Device not Available" error. Next I made a bootable USB flash drive, but receive the same error as the CD drive. The BIOS recognizes the CD and flash drives, and they appear in the boot device list, but neither will boot. I've attempted to resolve this by re-arranging the boot order in the BIOS and switching IDE channels/setting jumpers on the drives themselves, to no effect. I cannot move the hard drive to another machine because the XPS is the only one that supports SATA drives.

  Read the article

• Is Lojack preinstalled on Dell's laptops?

  - by Blorgbeard

  I'm looking at buying a Dell Studio 15 or similar. Unfortunately, they all seem to come with Lojack software included and no option to take it out of the build. I really do not want this software installed on my laptop. It sounds really abusable, and hard to get rid of once installed - it hides in your BIOS and survives reinstalls, etc. Does anyone know whether Lojack comes preinstalled on this machine, or if they just ship you a disc, which could subsequently be broken in half and/or microwaved into submission?

  Read the article

• Configuring NVIDIA Quadro with Dell Precision M4600

  - by vsecades

  After a frustrating couple of weeks when I recently bought my Dell Precision laptop, I managed to fix an issue where Ubuntu (yes, was NOT using Windows, get serious) would not recognize the video card and would cause all sorts of problems all over the place. I ended up one Saturday morning nearly throwing this thing away, when I managed to find a post about NVIDIA Optimus technology... ( http://www.pcmag.com/article2/0,2817,2358963,00.asp ). Now I am a huge advocate of disruptive new stuff, as long as we keep the broader audience in mind. Anyhow, disabling this (which as the BIOS settings state only work on Windows 7 or later), effectively allow the NVIDIA based Ubuntu driver to kick in full force. No need for a trash can anymore thankfully. As I saw multiple posts all over the place about this, check your BIOS, disable and try the video again to see if this corrects your issues. Best of luck!

  Read the article

• Dell D630 - Touchpad does not move the mouse cursor

  - by Dean McKenzie

  Windows XP - Dell D630 - Synaptics Touch Pad driver installed. The system tray icon that shows the movement of your finger on the touchpad registeres movement. The scroll feature of the touchpad works on any window with a scroll bar. The double click works even. But it never actually moves the cursor on the screen. An external mouse works with out problems, and I've replaced the palm-rest/touchpad and it continues to happen. The touch stick in the middle of the keyboard works without problems. Does anyone have any ideas?

  Read the article

• dell studio 1558 multi touchpad multi finger problem

  - by christian130

  Recently I bought an Intel Core i7 Dell laptop fully integrated. I have an ATi Radeon 1 gb ram graphic card and so on. Everything works fine even the brightness, but when I try the multi touch multi finger(touchpad which enables two or more finger) the pointer jump and go there and go here and so It's very annoying because when I'm trying to write this question I cannot let the pointer be cool! when I accidentally the touchpad it is very annoying. How can I fix this ?

  Read the article

• iPad USB Charging Utility for Dell Optiplex

  - by BreakPhreak

  As you probably know already, an iPad requires a certain power on USB port to be charged from. Thus, some motherboard manufacturers (such as ASUS, Gigabyte etc) had released a special driver that recognizes that an iPad is connected to the port and adjust the USB power accordingly. On one of my computers (Gigabyte motherboard) it works fine. But other one is Dell Optiplex 780 and the regular googling by "<motherboard type> + iPad charging" doesn't seem to bring encouraging results. Just for completeness: no, the iPad is not being charged without any special driver installed (out of the box) either. Any suggestions will be welcomed.

  Read the article

• Problems installing Windows 7 on Dell Inspiron 531 desktop

  - by wardedmocha

  Hello. I am having a problem installing Windows 7 on a Dell Inspiron 531 desktop. I got the setup to run and now it was trying to restart and now the computer just beeps. Two times a second, one right after the other. The beep is not like a key is being held down. And the computer isn't showing anything on the screen. edit: this is a computer I am trying to fix there where two blue screen errors that I know of. the first one had something to do with a display driver the second one was unknown

  Read the article

• Restoring Dell recovery disks while preserving Linux partition

  - by Flup

  I have a Dell laptop dual-booting to Windows 7 and Linux. I have through my own stupidity royally stuffed the Windows partition. I have the set of recovery DVDs that I created when I first got the laptop, and I've successfully booted from them in a VirtualBox VM and ended up with a fresh (albeit virtualised) installation of Windows 7. When I started the recovery process, there was mention of other partitions being preserved, but it was unclear as to whether non-NTFS partitions would survive the process. The question is: can I run the recovery procedure without risking my Linux partition?

  Read the article

• solve dell xps delay on touchpad and keyboard

  - by iim.hlk

  I finally found the complete solution for a frustrating/weird problem i was facing. Problem A ) there is a touchpad delay when typing and try to use the touchpad? problem B ) there is a 1 second delay when press any key and try to use left click button through touchpad? pd: i make this because i searched a lot to get this solved and i want to share the solution, dont want any rep... my pc is a dell xps l521x, but im pretty sure it will apply for any xps model.

  Read the article

• Dell eSATAp not working with some SATA disks

  - by pistache

  I have a Dell Inspiron XPS 15 (L502X) laptop, with an eSATAp port. I also have a Western Digital 1TB 3"5 SATA drive, that I'd like to use with the laptop. I bought a eSATAp <- SATA 22-pin cable (from Delock). When I use this cable my 3"5 HDD does NOT power up, no spin up. I thought that it's just this HDD taking too much power from the motherboard. However, I tested too with my 2"5 SATA HDD and it works successfully. Now the weird thing is that this 2"5 HDD takes 1.1A at 5V, and that the 3"5 HDD takes 0.7A at 5V. I don't understand why it can't work. Is there anything I could do for it to work ? What is really the problem ? Thanks for your help, Hugo

  Read the article

• Bringing my Dell XPS 13 ultrabook back to factory state

  - by TysHTTP

  I have a brand new Dell XPS 13 ultra book. After i picked it up at the store, i wiped the exising partitions which also contained the restore/rescue data, which you need to reinstall the factory version of Windows 8 that comes with this machine. I did this because we have a different MS partner edition of Windows which i prefer to run. After doing all this, i noticed that there was something wrong with machine. No real damage, but the specs are not completely as they should be. Turned out that a simple mistake while ordering. Now, long story short, the shop says that it has no problem with taking the product back, as long as it is in it's original state. And this is the problem i'm having, because i formatted the original partitions that contain that rescue option / windows 8 setup, i don't have a clue whether it's possible to get back to that original. Does anyone have an idea on how to get this fixed?

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >