Search Results

Search found 12330 results on 494 pages for 'old retired dude'.

Page 110/494 | < Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >

  • Apache log rotation: logrotate vs rotatelogs vs chronolog

    - by Enrico
    I have been researching log rotation for my server which hosts ~5 fairly high traffic sites. From what I can tell, my options are to use logrotate or to use piped logging with either rotatelogs or chronolog. logrotate requires a restart of apache and both SIGHUP and SIGUSR1 restarts are less than ideal on high traffic sites, because either you drop a bunch of connections or you need to delay compressing the old log until all child processes have died naturally. Also, downtime can be quite significant if compression is enabled. Would using logrotate - without compression and with graceful restart - and compressing old logs after the fact be the best way to minimize downtime? chronolog and rotatelogs sound promising, but are not well documented. I couldn't find examples of using either in combination with vhost specific logs. The chronolog website says, "when the expanded filename changes, the current file is closed and a new one opened". Is this globally? Or is that per AccessLog, CustomLog or ErrorLog directive? Is there a significant difference between chronolog and rotatelogs?

    Read the article

  • SuperMicro BMC on OpenSuSE Linux --cannot access from LAN

    - by Kendall
    Hi, I have an (old) SMC-001 IPMI device on an (old) X6DVL-EG2 motherboard. My problem is that I cannot access the BMC from LAN. I'm also getting some interesting output from ipmitool. First, the setup. I enable Console Redirection in the BIOS, turn BIOS Redirection after POSt to "disabled". I then modprobe'ed for ipmi_msghandler, ipmi_devintf and ipmi_si. I then found ipmi0 under /dev. So far so good. Since I want console redirection over serial, I modified /boot/grub/menu.lst: http://pastebin.com/YYJmhusQ I then modified "/etc/inittab" as follows: S1:12345:respawn:/sbin/agetty -L 19200 ttyS1 ansi Networking I set as following, using "ipmitool" ipaddr: 192.168.3.164 netmask: 255.255.255.0 defgw: 192.168.3.1 The above are correct for my environment. To test it I do: ipmitool -I open chassis power off which responds by powering off the machine. When I to access from another computer on the network, however, I get an error message: host# ipmitool -I lanplus -H 192.168.10.164 -U Admin -a chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status "Admin" seems to be a valid user name: host# ipmitool -I open user list 1 2 Admin true false true USER The interesting output from ipmitool I initially mentioned: host # ipmitool -I open lan set 1 access on Set Channel Access for channel 1 failed: Request data field length limit exceeded Also, newload4:/home/gjones # ipmitool channel info 1 Channel 0x1 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : session-less Active Session Count : 0 Protocol Vendor ID : 7154 Get Channel Access (volatile) failed: Request data field length limit exceeded The output of "ipmitool -I open lan print 1" is here: http://pastebin.com/UZyL6yyE Any help/suggestions is greatly appreciated; I've been working with this thing for a few hours now with no success.

    Read the article

  • Dell Poweredge 2600 RAID Transfer How-to

    - by DCookie
    Help, please! Hardware: Dell Poweredge 2600 PERC 4 SCSI Drives, 1 standalone 3 in a RAID 5 configuration OS: Windows 2000 Server In other words, a fairly old system. Anyway, we are in the process of taking over support for this site. The current tech wants out and is fading from view fast, so we need to solve this problem: The standalone disk (where the OS was) failed. We've replaced the disk, installed the OS, but need to know exactly how to proceed from here. I've never worked with a RAID system before, so I don't want to touch anything without knowing what I'm doing. We are not certain if the site will want us to attempt to recover the array or wait for the old tech to become available. We have replaced the server with a temporary box, and recovered MOST of the data from an online backup service. However, the other tech failed to backup a part of the data and the only copy of it is on this RAID array. Hence, our caution. We have poked minimally around in the boot-up PERC config utility, and it seems to me that that's where we'll need to be to reclaim the array. Another possibility is that there is some Dell software for the RAID controller we need to acquire. Can anyone provide clues as to how to proceed from here? Any help GREATLY appreciated.

    Read the article

  • File is not compatible with the version of Windows you're running

    - by vaccano
    I have a really old installer (legacy app) that we are trying to get running on a Windows 7 64 bit os. Previously it has only been installed on Windows XP 32 bit. I get the following error when I try to run it: The version of this file is not compatible with the version of Windows you're running. Check your computer's system information to see whether you need an x86 (32-bit) or x64 (64-bit) version of the program, and then contact the software publisher. Contacting the software publisher is not an option (software is super old). Is there a way to get this to work? Some sort of compatibility mode? The only thing I have heard of that will work is a Virtual XP on the Win 7 box. The problem is that this software is a part of a whole software set. I would have to put all of the pieces on the Virtual XP or none at all. Before I go down the road of putting it all on the virtual xp I would like to know that there is no way to get it all on the Win 7 os.

    Read the article

  • Everything on hard drive suddenly vanished without explanation, but the drive seems otherwise functional

    - by user160705
    Windows 7 Ultimate x64 Custom-built desktop I have a new desktop that I built a few months ago that has a four-year-old WD hard drive and a two-year-old drive. I had set it up so that the newer drive had Windows and most of my files on it while the older drive had my music library, some movies and games, and a backup of all of my documents. About a month ago, I installed some new case fans and, in the process, I temporarily unplugged my hard drive (while the computer was off of course - I took all the necessary precautions) for wire management. I plugged it back in, and didn't really think anything of it. At around that time, however, I noticed that my older hard drive wasn't showing up in Windows Explorer anymore but I didn't really have time to check into it (I had just started college) and I'm finally getting a chance to now. That drive doesn't show up in Windows Explorer at all but it does show up in Disk Management. That screen shows the following: http://puu.sh/17mMN Any idea what happened? Is there any way to recover my files? Thanks in advance for your help! EDIT: The music and games and stuff used to be on "Disc 1", the 465.71 GB of what is now showing as unallocated space.

    Read the article

  • Install MatroskaProp on Windows 7 x64

    - by Neophytos
    To see more information in Windows Explorer property pages and menus about Matroska Video (.mkv) files, similar to what one can see when selecting native Windows media (.avi, .asf, .wmv or even just plain old mpg) files, Matroska links (from http://www.matroska.org/downloads/windows.html) to a download of the MatroskaProp shell extension (http://www.jory.info/serendipity/archives/14-MatroskaProp-2.8-Released.html). It used to work for me under Windows XP 32-bit. Now I have Windows 7 x64, and downloaded, installed and ran it. Configuration and settings page is fine. But it does not seem to actually register any shell extension. Nothing is added to Explorer windows, menus or property pages when selecting .mkv or .mks files). I tried calling the register hook manually using regsvr32.dll, that again invoked the configuration window and let me set all options, and when confirming even said the registration succeeded, but seems to have had no effect. In the registry I cannot find any traces of the shell extension being installed. Can this extension be made to work under Windows 7 or x64 systems? Are there known problems with installing this or other old shell extensions on x64, or on Windows 7?

    Read the article

  • Failed to connect from slave to master with error "error connecting to master (1045)"

    - by Victor Lin
    I try to setup replication from slave to the master. CHANGE MASTER TO MASTER_HOST = 'master', MASTER_PORT = 3306, MASTER_USER = 'repl', MASTER_PASSWORD = 'xxx'; And I did grant privileges to the user on master. I can connect with mysql command from slave machine to the master mysql -h master -u repl -p mysql> show grants; GRANT RELOAD, SUPER, REPLICATION SLAVE, CREATE USER ON *.* TO 'repl'@'xxx' IDENTIFIED BY PASSWORD 'xxx' mysql> select 1; +---+ | 1 | +---+ | 1 | +---+ 1 row in set (0.04 sec) As you can see, privileges are correct, connection works fine, but however, the connection for replication to master always failed. mysql> show slave status\G *************************** 1. row *************************** Slave_IO_State: Connecting to master Master_Host: master Master_User: repl Master_Port: 3306 Connect_Retry: 60 Master_Log_File: Read_Master_Log_Pos: 4 Relay_Log_File: slave-replay-bin.000002 Relay_Log_Pos: 4 Relay_Master_Log_File: Slave_IO_Running: Connecting Slave_SQL_Running: Yes Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 0 Last_Error: Skip_Counter: 0 Exec_Master_Log_Pos: 0 Relay_Log_Space: 107 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL Master_SSL_Verify_Server_Cert: No Last_IO_Errno: 1045 Last_IO_Error: error connecting to master 'repl@master:3306' - retry-time: 60 retries: 86400 Last_SQL_Errno: 0 Last_SQL_Error: Replicate_Ignore_Server_Ids: Master_Server_Id: 0 1 row in set (0.00 sec) Is this caused by different version of MySQL server? The version of master is 5.0.77, and the slave is 5.5.13. But all articles I could find tell me that it's okay to replicate from a newer slave to old master. How to solve this problem? -- Update -- I even try to upgrade the old MySQL, but still, the problem is not solved. mysql> show slave status\G *************************** 1. row *************************** Slave_IO_State: Connecting to master Master_Host: master Master_User: repl Master_Port: 3306 Connect_Retry: 60 Master_Log_File: master-bin.000007 Read_Master_Log_Pos: 107 Relay_Log_File: slave-replay-bin.000001 Relay_Log_Pos: 4 Relay_Master_Log_File: master-bin.000007 Slave_IO_Running: Connecting Slave_SQL_Running: Yes Replicate_Do_DB: Replicate_Ignore_DB: Replicate_Do_Table: Replicate_Ignore_Table: Replicate_Wild_Do_Table: Replicate_Wild_Ignore_Table: Last_Errno: 0 Last_Error: Skip_Counter: 0 Exec_Master_Log_Pos: 107 Relay_Log_Space: 107 Until_Condition: None Until_Log_File: Until_Log_Pos: 0 Master_SSL_Allowed: No Master_SSL_CA_File: Master_SSL_CA_Path: Master_SSL_Cert: Master_SSL_Cipher: Master_SSL_Key: Seconds_Behind_Master: NULL Master_SSL_Verify_Server_Cert: No Last_IO_Errno: 1045 Last_IO_Error: error connecting to master 'repl@master' - retry-time: 60 retries: 86400 Last_SQL_Errno: 0 Last_SQL_Error: Replicate_Ignore_Server_Ids: Master_Server_Id: 0 1 row in set (0.00 sec)

    Read the article

  • SAS vs Near-line SAS vs SATA

    - by David
    I'm unsure about the differences in these storage interfaces. My Dell servers all have SAS RAID controllers in them and they seem to be cross-compatible to an extent. The Ultra-320 SCSI RAID controllers in my old servers were simple enough: One type of interface (SCA) with special drives with special controllers, humming at 10-15K RPM. But these SAS/SATA drives seem like the drives I have in my desktop, only more expensive. Also my old SCSI controllers have their own battery backup and DDR buffer - neither of these things are present on the SAS controllers. What's up with that? "Enterprise" SATA drives are compatible with my SAS RAID controller, but I'd like to know what advantage SAS drives have over SATA drives as they seem to have similar specs (but one is a lot cheaper). Also, how do SSDs fit into this? I remember when RAID controllers required HDDs to spin at the same rate (as if the controller card supplanted the controller in the drive) - so how does that work out now? And what's the deal with Near-line SATA? I apologise about the rambling tone in this message, it's 5am and I haven't slept much.

    Read the article

  • How do I force Windows 7 to recognize my Projector?

    - by user63564
    I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

    Read the article

  • How do I find out the Mac Address Firefox submits for Geolocation?

    - by Jim McKeeth
    I moved, but have the same router and cable box. Now when I visit Google Maps it still shows my old location. I went to the SkyhookWireless update page to update my Mac Address with my new location. The process is you put in your Mac address and it shows you the current location, and then you adjust that location and submit it. When I got the Mac Address from the status page on my router Skyhook reported that location as in Pakistan, which isn't even the correct continent (as my old or new address). I tried every other Mac address I could come up with: The cable router, the Wireless router's other Mac address, my PC's Mac address, etc. and none of them reported any location on the Skyhook page. So I am guessing that there is another Mac address, or some other bit of information that is used by Firefox when it reports to Google Maps my current location. Now that you have the back story, how do I find the Mac address or whatever information it is that Firefox (or other browsers) use to determine my Geolocation? Everything I have read online is rather vague. The next option I am considering is hooking a logging proxy onto Firefox and seeing what data it sends, but I'd rather find an easier method. Related: How do I update the geo location of my house?

    Read the article

  • How to verify PostgreSQL 9 has installed correctly on a CentOS server?

    - by A4J
    I'm trying to install the PG (postgres) gem on a CentoOS server, but it keeps saying Postgres is too old, even though I have upgraded it to 9.1.3 (as per the instructions here http://www.davidghedini.com/pg/entry/install_postgresql_9_on_centos). I am using CentOS 5.8 (and Ruby 1.9.3) Here is the error message: Building native extensions. This could take a while... ERROR: Error installing pg: ERROR: Failed to build gem native extension. /usr/local/bin/ruby extconf.rb checking for pg_config... yes Using config values from /usr/bin/pg_config checking for libpq-fe.h... yes checking for libpq/libpq-fs.h... yes checking for pg_config_manual.h... yes checking for PQconnectdb() in -lpq... yes checking for PQconnectionUsedPassword()... no Your PostgreSQL is too old. Either install an older version of this gem or upgrade your database. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. psql --version confirms my version: psql (PostgreSQL) 9.1.3 I can confirm packages installed: Setting up Install Process Package postgresql91-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-devel-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-server-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-libs-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-contrib-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Nothing to do Any ideas on how to troubleshoot this? Thanks in advance.

    Read the article

  • SQL Server 2008 cluster freezing

    - by Ed Leighton-Dick
    We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

    Read the article

  • Looking for updated BIOS for '99 Gateway in order to format/recognize >127 GB HD

    - by Jeff
    I have a '99 Gateway that's apparently too old for even Gateway to acknowledge it exists. Want to use it as a media hub and put in a 320GB HD, but it will not format above 127GB even running Win XP SP3. Read somewhere that upgrading the BIOS may do the trick, but I can't find the correct BIOS, and GW has been no help. Hoping I can just upgrade the BIOS, which is 11 years old. Any help would be much appreciated! I don't know where to look, and searches have been fruitless. System info: OS Name Microsoft Windows XP Home Edition Version 5.1.2600 Service Pack 3 Build 2600 OS Manufacturer Microsoft Corporation System Name xxxx System Manufacturer Gateway System Model TABOR_II System Type X86-based PC Processor x86 Family 6 Model 7 Stepping 3 GenuineIntel ~596 Mhz BIOS Version/Date Intel Corp. 4W4SB0X0.15A.0015.P10, 9/28/1999 SMBIOS Version 2.1 BIOS info (from a free app I located): BIOS Type: Phoenix BIOS Date: September 28th 1999 BIOS ID: 4W4SB0X0.15A.0015.P10.9909281445-None BIOS OEM: 4W4SB0X0.15A.0015.P10 Chipset: Intel 440BX/ZX rev 3 SuperIO: SMC 70x or 80x rev 0 at port 0370 Manufacturer: Gateway Motherboard: WS440BX

    Read the article

  • Compiling Mono on Fedora 7

    - by Gary
    Trying to install Mono from source on Fedora 7.. running # ./configure --prefix=/opt/mono works fine, but doing the make # make ; make install ends up with the following: Makefile:93: warning: overriding commands for target `csproj-local' ../build/executable.make:131: warning: ignoring old commands for target `csproj-local' make install-local make[6]: Entering directory `/opt/mono-2.6.4/mcs/mcs' Makefile:93: warning: overriding commands for target `csproj-local' ../build/executable.make:131: warning: ignoring old commands for target `csproj-local' MCS [basic] mcs.exe typemanager.cs(2047,40): error CS0103: The name `CultureInfo' does not exist in the context of `Mono.CSharp.TypeManager' Compilation failed: 1 error(s), 0 warnings make[6]: *** [../class/lib/basic/mcs.exe] Error 1 make[6]: Leaving directory `/opt/mono-2.6.4/mcs/mcs' make[5]: *** [do-install] Error 2 make[5]: Leaving directory `/opt/mono-2.6.4/mcs/mcs' make[4]: *** [install-recursive] Error 1 make[4]: Leaving directory `/opt/mono-2.6.4/mcs' make[3]: *** [profile-do--basic--install] Error 2 make[3]: Leaving directory `/opt/mono-2.6.4/mcs' make[2]: *** [profiles-do--install] Error 2 make[2]: Leaving directory `/opt/mono-2.6.4/mcs' make[1]: *** [install-exec] Error 2 make[1]: Leaving directory `/opt/mono-2.6.4/runtime' make: *** [install-recursive] Error 1 I've been following the instructions at http://ruakuu.blogspot.com/2008/06/installing-and-configuring-opensim-on.html. This is all in an effort to get OpenSimulator running.

    Read the article

  • Apache 2.2 Present rss http 410 pages as application/rss+xml content type

    - by Mark Bakker
    I have a problem sending http-410 for very old rss feeds. Functional this can happen in one Very old rss feeds where content is not updated anymore / subject could not move to another feed Migration from 3th party site to our site where the rss feed is not longer functional supported I tried several things in my site config see below; <VirtualHost *:80> DocumentRoot /opt/tomcat/webapps/ROOT/ ErrorDocument 500 /error/static/error-500.html ErrorDocument 503 /error/static/error-500.html ErrorDocument 404 /error/static/rss/error-404.html ErrorDocument 410 /error/static/rss/error-410.html # When error pages need to be served by apache, # exclude the files to serve as below (in comment) SetEnvIf Request_URI "/error/static/*" no-jk # force all files to be image/gif: <Location *.rss> #<Location *> #ForceType application/rss+xml </Location> #AddType application/rss+xml .rss #AddType application/rss+xml .xml #AddType application/rss+xml .html JkMount /* rss;use_server_errors=402 # JkMount /* rss RewriteEngine on JkMount /news.rss rss JkMount /documenten-en-publicaties.rss rss RewriteEngine on RewriteRule ^/news.rss$ - [NC,T=application/rss+xml,G,L] RewriteRule ^/documenten-en-publicaties.rss$ - [NC,G,L] # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn ErrorLog "|/usr/bin/logger -s -p local3.err -t 'Apache'" CustomLog "|/usr/bin/logger -s -p local2.info -t 'Apache'" combined ServerSignature Off </VirtualHost> The desired end result should be on /news.rss and /documenten-en-publicaties.rss a 410 page with content in the error page with a content type 'application/rss+xml'

    Read the article

  • How can I automatically restart Apache and Varnish if can't fetch a file?

    - by Tyler
    I need to restart Apache and Varnish and email some logs when the script can't fetch robots.txt but I am getting an error ./healthcheck: 43 [[: not found My server is Ubuntu 12.04 64-bit #!/bin/sh # Check if can fetch robots.txt if not then restart Apache and Varnish # Send last few lines of logs with date via email PATH=/bin:/usr/bin THEDIR=/tmp/web-server-health [email protected] mkdir -p $THEDIR if ( wget --timeout=30 -q -P $THEDIR http://website.com/robots.txt ) then # we are up touch ~/.apache-was-up else # down! but if it was down already, don't keep spamming if [[ -f ~/.apache-was-up ]] then # write a nice e-mail echo -n "Web server down at " > $THEDIR/mail date >> $THEDIR/mail echo >> $THEDIR/mail echo "Apache Log:" >> $THEDIR/mail tail -n 30 /var/log/apache2/error.log >> $THEDIR/mail echo >> $THEDIR/mail echo "AUTH Log:" >> $THEDIR/mail tail -n 30 /var/log/auth.log >> $THEDIR/mail echo >> $THEDIR/mail # kick apache echo "Now kicking apache..." >> $THEDIR/mail /etc/init.d/varnish stop >> $THEDIR/mail 2>&1 killall -9 varnishd >> $THEDIR/mail 2>&1 /etc/init.d/varnish start >> $THEDIR/mail 2>&1 /etc/init.d/apache2 stop >> $THEDIR/mail 2>&1 killall -9 apache2 >> $THEDIR/mail 2>&1 /etc/init.d/apache2 start >> $THEDIR/mail 2>&1 # prepare the mail echo >> $THEDIR/mail echo "Good luck troubleshooting!" >> $THEDIR/mail # send the mail sendemail -o message-content-type=html -f [email protected] -t $EMAIL -u ALARM -m < $THEDIR/mail rm ~/.apache-was-up fi fi rm -rf $THEDIR

    Read the article

  • File transfer from MP3 player to computer

    - by JP
    I own an old 20GB Creative Zen jukebox (all external screws are gone on it LOL) and I would like to transfer files back to my PC to get them on my new iPod. Problem is, no matter what software I use (WinAMP, Creative Media Source or Windows Media Player), it just stops transferring files on my HD with an error message that says there is no more space on the destination folder. Problem is, there is still 320GB free. I tried lot of things like installing newer driver, latest Zen plug-in for Media Source, latest WinAMP version. Sometimes, it just works and then again, it stops working and I get this non-sense error. Restarting my PC sometime solves the issue by giving me enough time to transfer 10 or 15 more files and then I get the error again and again. Yesterday though I managed to transfer up to 3GB of MP3s on my computer before getting the error. Seems like I'm having a driver issue or a weird behavior from the player and/or the software I'm using. 3 different software can't reproduce the exact same issue by themselves so it must be something related to the driver. I can't find any post of any sort concerning such issue on old forums. Any idea?

    Read the article

  • NIS: which mechanism hides shadow.byname for unpriviledged users?

    - by Mark Salzer
    On some Linux box (SLES 11.1) which is a NIS client I can do as root: ypcat shadow.byname and get output, i.e. some lines with the encrypted passwords, amongst other information. On the same Linux box, if I run the same command as unpriviledged user, I get No such map shadow.byname. Reason: No such map in server's domain Now I am surprised. My good old knowlege says that shadow passwords in NIS are absurd because there is no access control or authentication in the protocol and thus every (unpriviledged) user can access the shadow map and thereby obtain the encrypted passwords. Obviously we have a different picture here. Unfortunately I don't have access to the NIS server to figure out what is happening. My only guess is that the NIS master gives the map only to clients conection from a priviledged port (1024), but this is only an uneducated guess. What mechanisms are there in current NIS implementations to lead to a behavior like the above? How "secure" are they? Can the be circumvented easily? Or are shadow passwords in NIS as secure as the good old shadow files?

    Read the article

  • Performance of Virtual machines on very low end machines

    - by TheLQ
    I am managing a few cheap servers as my user base isn't large enough to get much more powerful servers. I also don't have the money lying around to invest in a server to prepare for the larger user base. So I'm stuck with the old hardware I have. I am toying with the idea of virtualizing all the current OS's with most likely VMware vSphere Hypervisor (AKA ESXi) Xen (ESXi has too strict of an HCL, and my hardware is too old). Big reasons for doing so: Ability to upgrade and scale hardware rapidly - This is most likely what I'll be doing as I distribute services, get a bigger server, centralize (electricity bills are horrible), distribute, get a bigger server, etc... Manually doing this by reinstalling the entire OS would be a big pain Safety from me - I've made many rookie mistakes, like doing lots of risky work on a vital production server. With a VM I can just backup the state, work on my machine, test, and revert if necessary. No worries, and no OS reinstallation Safety from other factors - As I scale servers might go down, and a backup VM can instantly be started. Various other reasons. However the limiting factor here is hardware. And I mean very depressing hardware. The current server's run off of a Pentium 3 and 4, and have 512 MB and 768 MB RAM respectively (RAM can be upgraded soon however). Is the Virtualization layer small enough to run itself and a Linux OS effectively? Will performance be acceptable (50% CPU overhead for every operation isn't acceptable)? Does it leave enough RAM for the Linux OS? Is this even feasible?

    Read the article

  • Missing Home Folder XP Clients 2008R2 Domain

    - by minamhere
    We just completed a migration from Server 2003 to Server 2008R2. Everything seems to have gone well except that many of our desktops have stopped mapping the Home Folder as set in Active Directory. Other mappings that are defined on individual clients are mapping just fine, these mappings are all on the same file server as the failing Home Folders. Half of the users are on 1 file server and half are on another. Users from both servers are having this problem. I have enabled the Group Policy setting to "Wait for network before logging in". I enabled the policy to "Run Logon Scripts synchronously". There are no errors on the Domain Controller or either File Server. When I enabled Group Policy Preferences as an attempted workaround, I get this error: The user 'V:' preference item in the '<Policy Name>' Group Policy object did not apply because it failed with error code '0x800708ca This network connection does not exist.' This error was suppressed. This seems to indicate that the network connection is not ready by the time Group Policy is processed. But isn't this the point of the "Wait before logging in" and "Run Logon scripts synchronously" settings? Some other background facts: The new Server 2008R2 installation is a Virtual Machine. It is on a new Subnet in a different building from the old server. DNS and DHCP were also migrated from the old DC to this new DC. These Home Folders were all working properly before the migration. Are there new security restrictions/policies in Server 2008R2 that might be causing this? Is there a way to check whether I have an underlying network connectivity issue? Maybe moving the server to the new building is causing a delay/timeout? Any thoughts or ideas on what could be causing this or how I can resolve this? Thanks.

    Read the article

  • Troubleshooting Mid 2007 iMac RAM upgrade

    - by MDT
    I am trying to install new RAM in my friends iMac, something I have done several times before. We unplugged the computer before performing the upgrade, used anti static wrist bands, and yes the memory is compatible and inserted correctly. The stock RAM was Hynix 1gb pc2-5300s-555-12 and the memory we are replacing it with is 2x2gb Centon CMP800SO2048.01. Now I know this model number suggests that the ram is 800MHz and the iMac is only 667MHz but it clearly states on the box that this RAM is PC2-5300 667MHz compatible. The problem is, that when I install the new RAM I get little response from the computer. I hear the hard drive and disk drive start to initialize, but then they just stop and the screen remains black. I have tried every variation of the new RAM and the old RAM in both slots and even tried the same RAM from my old iMac and I just can't get it to boot. Has anyone ever had a problem like this? Thank you in advance for any and all input on thus issue!

    Read the article

  • Black Screen and System Hang - Possibly CPU overheating

    - by Mahesh
    I have this old computer - P4 2.0ghz, 1.2GB RAM and onboard graphics(no external card), 80GBHDD. It has xubuntu installed on it and it regularly hangs when it takes more system resources for say like graphical programs, too many tabs on firefox etc. It just either hangs the system or shows black screen. Tested if it was issue of HD but it wasn't because i have used linux livecd and problem is still the same even if I have removed the HD. I have also tested with USB linux (puppy linux and ubuntu linux on 8gb drives). Tested windows XP as well on this HD and results are the same. Tested another HD on this machine, results are still the same with it. System hangs or goes black screen and requires restart. I thought later it could be thermal heat issue and then applied thermal paste on heatsink but still it fails to work for me. It continues to show symptoms. Another thing which was yet to be tested is changing of CPU fan which was not done because I have not found any fan for old pentium 4 machine in the market. I have to hit online stores (but i am in india and it's hard to find it in online shops which can deliver it to me). So far I don't see this as HD or Monitor or OS issue because I have tested with other HD and results are the same. So it could be either CPU fan or motherboard? What could be possible issue with the hardware?

    Read the article

  • Using multiple computers effectively

    - by Benjamin Oakes
    I have some extra (old) Macs and PCs around the house and a MacBook that's sometimes overworked. I'm looking for tips on using multiple computers effectively. Basically, I'd like to add to the following list. Here's what I'm using so far: Teleport: lets you use a single mouse and keyboard to control several Macs, like Synergy Built-in file sharing: lets me run programs on another Mac, but only maintain one copy of the data Bazaar: distributed version control Mail.app, Thunderbird, etc.: IMAP for my mail accounts TuneConnect: control iTunes on another Mac with a nice interface, using the library on my MacBook (if I choose it by pressing option at startup) over file sharing OmniFocus: syncs across computers pretty seamlessly Web browsing across computers VNC/Remote Desktop Running X-windows programs using ssh -Y hostname for headless operation (but they die when I sleep the connecting computer -- something like GNU screen would be ideal) Plain-old ssh with GNU screen Really, a better idea of what I do might be necessary. Generally though, I'd like to distribute tasks across more than one computer when possible, but not have much overhead in doing so. The perfect solution? An Xgrid-like program that pushes processing across multiple computers automatically and seamlessly (although that seems unlikely). Here's what I have, in case it makes a difference: MacBook (Dual 2.16 GHz, OS X 10.6.3) eMac (1.25 GHz, OS X 10.4.11, soon to be 10.5) Dell Dimension (800 MHz, some version of Ubuntu) -- no dedicated monitor PowerMac G3 (400 MHz, OS X 10.4.11) -- no dedicated monitor iMac G3 DV (400 MHz, OS X 10.4.11) -- currently in the kitchen for recipes, email, web browsing, music, movies (DVDs), etc. (Total, they cost me around $650, mostly for the MacBook. Freecycle is wonderful, just in case you haven't heard of it.) I'm really only using the MacBook and eMac at this point, but I'd like to push more onto it and possibly the PowerMac and Dell.

    Read the article

  • Serving images from another hostname vs Apache overload for the rewrites

    - by luison
    We are trying to improve further the speed of some sites with older HTML in order as well to obtain better SEO results. We have now applied some minify measures, combined html, css etc. We use a small virtualized infrastructure and we've always wanted to use a light + standar http server configuration so the first one can serve images and static contents vs the other one php, rewrites, etc. We can easily do that now with a VM using the same files and conf of vhosts (bind mounts) on apache but with hardly any modules loaded. This means the light httpd will have smaller fingerprint that would allow us to serve more and quicker, have more minSpareServer running, etc. So, as browsers benefit from loading static content from different hostnames as well, we've thought about building a rewrite rule on our main server (main.com) to "redirect" all images and css *.jpg, *.gif, *.css etc to the same at say cdn.main.com thus the browser being able to have more connections. The question is, assuming we have a very complex rewrite ruleset already (we manually manipulate many old URLs for SEO) will it be worth? I mean will the additional load of main's apache to have to redirect main.com/image.jpg (I understand we'll have to do a 301) to cdn.main.com/image.jpg + then cdn.main.com having to serve it, be larger than the gain we would be archiving on the browser? Could the excess of 301s of all images on a page be penalized by google? How do large companies work this out, does the original code already include images linked from the cdn with absolute paths? EDIT Just to clarify, our concern is not to do so much with server performance or bandwith. We could obviously employ an external CDN server but we have plenty CPU and bandwith. Our concern is with how to have "old" sites with plenty semi-static HTML content benefiting from splitting connections for images and static content via apache without having to change the html to absolute paths (ie. image.jpg to cdn.main.com/image.jpg happening on the server not the code)

    Read the article

  • Update BIOS on Sun Fire X4150 server

    - by Massimo
    I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

    Read the article

< Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >