Search Results

Search found 41497 results on 1660 pages for 'fault'.

Page 112/1660 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• Too much memory consumed during TFS automated build

  - by Bernard Chen

  We're running TFS 2010 Standard Edition, and we've set up an automated build to run whenever someone checks in code. We run through all of the automated tests (built with MSTest) as part of the build. We've configured the build to run the tests as a 64-bit process, but the QTAgent.exe that runs the tests grows in memory while the tests are running. It is currently reaching 8GB for the ~650 tests we have, and the process has slowed significantly when we went from 450 tests to 650 tests. When we run all of the tests in the local development environment, memory seems to be freed at least with each TestClass and never exceeds a certain level. The process of running all tests has not increased significantly in the local development environment. Is there a way to configure the build service to free up memory with each Test or each TestClass? With the way things are currently running, the build process gets very slow when we start to run out of memory on the machine. Edit: I found the MSTest invocation in the build log and ran it manually and saw the same behavior of runaway memory. I removed the /publish, /publishbuild, /teamproject, /platform, and /flavor parameters from the invocation of MSTest, in case the test runner was holding onto results until the end, but the behavior didn't change. I ran the same command line on a dev box, separate from the build server, and the memory freed up frequently. It seems there must be something wrong/different about the build server that is causing it to behave different, but I'm stumped where to look. I've looked at qtagent.exe.config, mstest.exe.config, versions of both executables. What else might affect this?

  Read the article

• Getting a list of patches in an HPSA patch policy

  - by asm

  I'm trying to get a list of patches contained in a Patch Policy in HPSA -- I can get what I need via the Twister web interface (under PatchPolicy.getPatches(), give it an ID, and it happily returns a list of patches contained.) -- I'm having a hard time getting this to work via the Pytwist interface, though... I haven't used the Pytwist interface for much besides some very basic Device manipulation, and Python is.. not my forte. I create the TwistServer object, then a PatchPolicy object from that (which I think is working..), but can't figure out how/where to call the getPatches() method from in Python-land. If there's a way to dig this out of the database itself, that would work, too, but I can't seem to find much in there along these lines besides the vendor-recommended patching stuff, and we use custom policies.

  Read the article

• Getting 0x80070043 error when accessing Samba share from Windows 7

  - by FelixM

  I created a Samba share on my new Ubuntu 10.04 machine. When I try to access it from a Windows 7 client, I get network error 0x80070043 (The network path not found). However, I get this error when I click on the share in the Windows Explorer, so it seems that Windows does find the path. I already enabled NTLMv1, disabled 128bit security and made sure that NetBIOS is running. I briefly disabled the Windows firewall, it didn't make a difference. What could be the problem?

  Read the article

• VMWare ESX, storage over 2TB

  - by Phliplip

  Hi, First of, i'm a webdeveloper and my server experience lies in setting up FreeBSD servers for webserver. I'm working on a project for at photographer, and i'm hired to develop a new online photo ordering system - where user of course can view their photos :) They have a massive need of storage, thus we have bought a HP G6 and 8x1TB SATA HDD. Our plan is to install VMWare ESX 4.0, running multiple virtual machines; FreeBSD 8 for webserver and some windows servers. Allready done that. Then mount one big storage to the BSD, and share it through Samba to the WinServers. The raid is set up with an array of 2x 1TB to handle the VMs. And the rest is setup as 3 2x1TB to handle the photo-data. Thus 2.73TB for photo-data (the raids are 1+0). Now if we add a datastore in the ESX and add the 3 LUNs we can get a datastore of 2.74TB. But i don't se how i can add this datastore direct to the VM. Only the BSD VM needs access to this. Only way is to create a VirtualDisk, with a max of 2TB (8MB blocksize). This is because the datastore where we save the virtualdisk has a maximum filesize of 2TB. Then add it as a harddisk to the BSD VM. In the 'Add Harddisk' pane for the VM, i see an option for Raw Disk Management. I think this is to access the datastore or the raid directly. Only problem is that its greyed out! Can i access the datastorage directly from the BSD? Without creating and adding virtualdisk.

  Read the article

• Unable to Create System DSN

  - by Baxter

  Environment: Windows 7 Professional 64-bit Operating System Problem: (ODBC Data Source Administrator) Opening Administrative Tools - Data Sources (ODBC) - Click "System DSN" tab. Error: ODBC System DSN Warning You are logged on with non-Administrative privileges. System DSNs could not be created or modified. Failed Troubleshooting so far: Enabled local Administrator account logged in under this account. Navigated to C:\Windows\System32\ right clicked odbcad32.exe Run as Administrator Notes: I am an Administrator on this machine. The 32-bit version runs fine if I open C:\Windows\SysWoW64\odbcad32.exe However, I need the data source to be 64-bit. I am not experiencing this problem on any of my other 64-bit machines. Any help would be greatly appreciated.

  Read the article

• uwsgi_params not in nginx

  - by Halit Alptekin

  Firstly I setup nginx and uwsgi via apt-get. And,I add the line to nginx conf file(/etc/nginx/conf.d/default.conf) like below line; server { listen 80; server_name <replace with your hostname>; #Replace paths for real deployments... access_log /tmp/access.log; error_log /tmp/error.log; location / { include uwsgi_params; uwsgi_pass 127.0.0.1:8889; } } I had a error; Starting nginx: [emerg]: open() "/etc/nginx/uwsgi_params" failed (2: No such file or directory) in /etc/nginx/conf.d/default.conf:11 configuration file /etc/nginx/nginx.conf test failed If I add uwsgi_params file from uwsgi's source;I had a simple error. Thanks

  Read the article

• Do you have to work with Ruby to make nginx_http_push_module work

  - by Saif Bechan

  I am interested to work with the nginx_http_push_module. It says something about using comet, and I see some code example of ruby. I want to know if this is just used as an example or is this the only way to have it to work. I want to use this module in combination with Node.js, server side JavaScript. With this I want to create a data-stream from the server to the client.

  Read the article

• Prosody mod auth external not working

  - by Yang

  I installed mod_auth_external for 0.8.2 on ubuntu 12.04 but it's not working. I have external_auth_command = "/home/yang/chat/testing" but it's not getting invoked. I enabled debug logging and see no messages from that mod. Any help? I'm using the Candy example client. Here's what's written to the log after I submit a login request (and nothing in err log): Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40527 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: %s) Oct 24 21:02:43 boshb344ba85-fbf5-4a26-b5f5-5bd35d5ed372 debug BOSH session created for request from 169.254.11.255 Oct 24 21:02:43 mod_bosh info New BOSH session, assigned it sid 'b344ba85-fbf5-4a26-b5f5-5bd35d5ed372' Oct 24 21:02:43 httpserver debug Sending response to bf9120 Oct 24 21:02:43 httpserver debug Destroying request bf9120 Oct 24 21:02:43 httpserver debug Request has destroy callback Oct 24 21:02:43 socket debug server.lua: closed client handler and removed socket from list Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 0 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 socket debug server.lua: accepted new client connection from 127.0.0.1:40528 to 5280 Oct 24 21:02:43 mod_bosh debug BOSH body open (sid: b344ba85-fbf5-4a26-b5f5-5bd35d5ed372) Oct 24 21:02:43 mod_bosh debug Session b344ba85-fbf5-4a26-b5f5-5bd35d5ed372 has 1 out of 1 requests open Oct 24 21:02:43 mod_bosh debug and there are 0 things in the send_buffer Oct 24 21:02:43 mod_bosh debug Have nothing to say, so leaving request unanswered for now Oct 24 21:02:43 httpserver debug Request c295d0 left open, on_destroy is function(mod_bosh.lua:81) Here's the config I added: modules_enabled = { ... "bosh"; -- Enable BOSH clients, aka "Jabber over HTTP" ... } authentication = "external" external_auth_protocol = "generic" external_auth_command = "/home/yang/chat/testing"

  Read the article

• How to set shmall, shmmax, shmni, etc ... in general and for postgresql

  - by jpic

  I've used the documentation from PostgreSQL to set it for example this config: >>> cat /proc/meminfo MemTotal: 16345480 kB MemFree: 1770128 kB Buffers: 382184 kB Cached: 10432632 kB SwapCached: 0 kB Active: 9228324 kB Inactive: 4621264 kB Active(anon): 7019996 kB Inactive(anon): 548528 kB Active(file): 2208328 kB Inactive(file): 4072736 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 3432 kB Writeback: 0 kB AnonPages: 3034588 kB Mapped: 4243720 kB Shmem: 4533752 kB Slab: 481728 kB SReclaimable: 440712 kB SUnreclaim: 41016 kB KernelStack: 1776 kB PageTables: 39208 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 8172740 kB Committed_AS: 14935216 kB VmallocTotal: 34359738367 kB VmallocUsed: 399340 kB VmallocChunk: 34359334908 kB HardwareCorrupted: 0 kB AnonHugePages: 456704 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 12288 kB DirectMap2M: 16680960 kB >>> ipcs -l ------ Shared Memory Limits -------- max number of segments = 4096 max seg size (kbytes) = 4316816 max total shared memory (kbytes) = 4316816 min seg size (bytes) = 1 ------ Semaphore Limits -------- max number of arrays = 128 max semaphores per array = 250 max semaphores system wide = 32000 max ops per semop call = 32 semaphore max value = 32767 ------ Messages Limits -------- max queues system wide = 31918 max size of message (bytes) = 8192 default max size of queue (bytes) = 16384 sysctl.conf extract: kernel.shmall = 1079204 kernel.shmmax = 4420419584 postgresql.conf non defaults: max_connections = 60 # (change requires restart) shared_buffers = 4GB # min 128kB work_mem = 4MB # min 64kB wal_sync_method = open_sync # the default is the first option checkpoint_segments = 16 # in logfile segments, min 1, 16MB each checkpoint_completion_target = 0.9 # checkpoint target duration, 0.0 - 1.0 effective_cache_size = 6GB Is this appropriate ? If not (or not necessarily), in which case would it be appropriate ? We did note nice performance improvements with this config, how would you improve it ? How should kernel memory management parameters be set ? Can anybody explain how to really set them from the ground up ?

  Read the article

• Cisco Pix 501 - reaching local host limit, showing odd IP addresses

  - by cdonner

  I am running out of licenses on my Pix 501, and the show local-host command lists a number of odd IP addresses that do not belong to my 10.10.1.* subnet. Any idea what they are? The only thing I could find was a potential ISP: DINSA is Defence Interoperable Network Services Authority, an agency of the Ministry of Defence of the United Kingdom. Does not sound right. I don't see any active connections, though. I can't ping or traceroute these IPs, but they reappear after I clear the list, with various other addresses in that general range, up until the connection limit is reached. Based on the number denied, I suppose I would have a lot more of them had I not the connection limit. Very dubious. Is anybody else seeing this? pixfirewall# show local-host Interface inside: 10 active, 10 maximum active, **118 denied** local host: <10.10.1.110>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.176>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.170>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 1/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.175>, TCP connection count/limit = 11/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 1/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.108>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.33.41.115>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.33.226.124>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.172>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <25.36.114.91>, // ???????????????? what is this? TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): local host: <10.10.1.109>, TCP connection count/limit = 0/unlimited TCP embryonic count = 0 TCP intercept watermark = unlimited UDP connection count/limit = 0/unlimited AAA: Xlate(s): Conn(s): pixfirewall#

  Read the article

• Comparing floating-point performance of Gflops and SPECfp.

  - by Marcelo Cantos

  I have performance numbers for two servers, but one reports Gflops and the other a SPECfp score. Is there a simple rule of thumb for comparing these two units of measure?

  Read the article

• Failed MDADM Array With Ext.4 Partition - "e2fsck: unable to set superblock flags on /dev/md0"

  - by Matthew Hodgkins

  Had a power failure and now my mdadm array is having problems. sudo mdadm -D /dev/md0 [hodge@hodge-fs ~]$ sudo mdadm -D /dev/md0 /dev/md0: Version : 0.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Array Size : 8790815232 (8383.57 GiB 9001.79 GB) Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 7 Total Devices : 7 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Sat Aug 7 19:10:28 2010 State : clean, degraded, recovering Active Devices : 6 Working Devices : 7 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 128K Rebuild Status : 10% complete UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1307608 Number Major Minor RaidDevice State 0 8 81 0 active sync /dev/sdf1 1 8 97 1 active sync /dev/sdg1 2 8 113 2 active sync /dev/sdh1 3 8 65 3 active sync /dev/sde1 4 8 49 4 active sync /dev/sdd1 7 8 33 5 spare rebuilding /dev/sdc1 6 8 16 6 active sync /dev/sdb sudo mount -a [hodge@hodge-fs ~]$ sudo mount -a mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so sudo fsck.ext4 /dev/md0 [hodge@hodge-fs ~]$ sudo fsck.ext4 /dev/md0 e2fsck 1.41.12 (17-May-2010) fsck.ext4: Group descriptors look bad... trying backup blocks... /dev/md0: recovering journal fsck.ext4: unable to set superblock flags on /dev/md0 sudo dumpe2fs /dev/md0 | grep -i superblock [hodge@hodge-fs ~]$ sudo dumpe2fs /dev/md0 | grep -i superblock dumpe2fs 1.41.12 (17-May-2010) Primary superblock at 0, Group descriptors at 1-524 Backup superblock at 32768, Group descriptors at 32769-33292 Backup superblock at 98304, Group descriptors at 98305-98828 Backup superblock at 163840, Group descriptors at 163841-164364 Backup superblock at 229376, Group descriptors at 229377-229900 Backup superblock at 294912, Group descriptors at 294913-295436 Backup superblock at 819200, Group descriptors at 819201-819724 Backup superblock at 884736, Group descriptors at 884737-885260 Backup superblock at 1605632, Group descriptors at 1605633-1606156 Backup superblock at 2654208, Group descriptors at 2654209-2654732 Backup superblock at 4096000, Group descriptors at 4096001-4096524 Backup superblock at 7962624, Group descriptors at 7962625-7963148 Backup superblock at 11239424, Group descriptors at 11239425-11239948 Backup superblock at 20480000, Group descriptors at 20480001-20480524 Backup superblock at 23887872, Group descriptors at 23887873-23888396 Backup superblock at 71663616, Group descriptors at 71663617-71664140 Backup superblock at 78675968, Group descriptors at 78675969-78676492 Backup superblock at 102400000, Group descriptors at 102400001-102400524 Backup superblock at 214990848, Group descriptors at 214990849-214991372 Backup superblock at 512000000, Group descriptors at 512000001-512000524 Backup superblock at 550731776, Group descriptors at 550731777-550732300 Backup superblock at 644972544, Group descriptors at 644972545-644973068 Backup superblock at 1934917632, Group descriptors at 1934917633-1934918156 sudo e2fsck -b 32768 /dev/md0 [hodge@hodge-fs ~]$ sudo e2fsck -b 32768 /dev/md0 e2fsck 1.41.12 (17-May-2010) /dev/md0: recovering journal e2fsck: unable to set superblock flags on /dev/md0 sudo dmesg | tail [hodge@hodge-fs ~]$ sudo dmesg | tail EXT4-fs (md0): ext4_check_descriptors: Checksum for group 0 failed (59837!=29115) EXT4-fs (md0): group descriptors corrupted! EXT4-fs (md0): ext4_check_descriptors: Checksum for group 0 failed (59837!=29115) EXT4-fs (md0): group descriptors corrupted! Please Help!!!

  Read the article

• ZFS on Linux for RHEL/OEL NFS Sharing

  - by BBK

  I'm trying ZFS on Linux for Oracle Linux (OLE) 6.1 (Red Hat RHEL 6.1 compatible clone). I successfully compiled and installed spl and zfs on it for Oracle Unbreakable Kernel. Zfs is working and I created mirror by zpool create -f -o ashift=12 tank mirror sdb sdc Now I'm trying to share my zfs pool caled "tank/nfs" as mentioned at zfsonlinux site. zfs set sharenfs=on tank/nfs So I created tank/nfs and set nfs to on. Now I'm trying to mount nfs share at local host to test it by mount -t nfs4 127.0.0.1:/tank/nfs /mnt But I get mount.nfs4: mount system call failed So question is: How to share NFS Folder or iSCSI Volumes at OLE rightly and mount it with Linux Client via ZFS on Linux.

  Read the article

• Reset crawled content for one content source in MOSS

  - by Andrew Strong

  I'm using MOSS 2007 and I want to wipe out the search index and do a full re-crawl of one of my content sources. I see the link to 'Reset all crawled content' but I don't want to have to re-crawl the other content sources. Is there any way to do this?

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by bakytn

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed)

  Read the article

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. Any clue as to what went wrong?

  Read the article

• Error "403 Forbidden" on Sharepoint Search Settings Page

  - by user21924

  Hello I thought I had solved this nightmare by re-entering the values in my SSP properties set up, however accessing the Search Settings page error has reared it ugly head again. Now all solutions point to this method listed here * http://www.routtlogics.com/blog/Lists/Posts/Post.aspx?ID=6 * http://social.technet.microsoft.com/Forums/en-US/sharepointadmin/thread/f00651cd-e452-45b9-b19e-90e89c3c3ad4 * http://blogs.technet.com/sushrao/archive/2009/03/26/microsoft-office-sharepoint-server-2007-moss-403-forbidden-error-when-clicked-on-search-settings-page.aspx The above workaround(s) basically states that granting the local group WSS_WPG read and write permission to the Task folder in the Windows directory would solve the problem, however whenever I try to change to the permission attribute of this folder I get an access denied message, even when logged in as a Domain administrator, Enterprise and even the SharePoint Farm administrator. Please guys how do I get around this access denied issue. Thanks

  Read the article

• Specify IPSEC port range using ipsec-tools

  - by Sandman4

  Is it possible to require IPSEC on a port range ? I want to require IPSEC for all incoming connections except a few public ports like 80 and 443, but don't want to restrict outgoing connections. My SPD rules would look like: spdadd 0.0.0.0/0 0.0.0.0/0[80] tcp -P in none; spdadd 0.0.0.0/0 0.0.0.0/0[443] tcp -P in none; spdadd 0.0.0.0/0 0.0.0.0/0[0....32767] tcp -P in esp/require/transport; In setkey manpage I see IP ranges, but no mention of port ranges. (The idea is to use IPSEC as a sort of VPN to protect internal communications between multiple servers. Instead of configuring permissions basing on source IPs, or configuring specific ports, I want to demand IPSEC on anything which is not meant to be public - I feel it's less error-prone this way.)

  Read the article

• Which Linux distro for Mac Mini?

  - by spoon16

  I recently received a Mac Mini and would like to set it up as a web server and git source server. I would like to learn Linux so am interested in setting up my Mac Mini with Linux instead of OSX. Here are the main things that I will be using the Mac Mini for. git Repositories (via Gitosis) build server (build projects in git repositories using commit hooks and run tests) simple websites (PHP) learning C++ in a non-Windows environment What distribution would you recommend? Please provide some detail in your answer so that I can make an meaningful decision. Because I am looking to use the mini as more of a server than a normal desktop machine I was thinking of Ubuntu Server, I'm not sure if that is over kill though given the hardware I am using.

  Read the article

• squid ssl bump sslv3 enforce to allow old sites

  - by Shrey

  Important: I have this question on stackoverflow but somebody told me this is more relevant place for this question. Thanks I have configured squid(3.4.2) as ssl bumped proxy. I am setting proxy in firefox(29) to use squid for https/http. Now it works for most sites, but some sites which support old SSL proto(sslv3) break, and I see squid not employing any workarounds for those like browsers do. Sites which should work: https://usc-excel.officeapps.live.com/ , https://www.mahaconnect.in As a workaround I have set sslproxy_version=3 , which enforces SSLv3 and above sites work. My question: is there a better way to do this which does not involve enforcing SSLv3 for servers supporting TLS1 or better. Now I know openssl doesn't automatically handle that. But I imagined squid would. My squid conf snipper: http_port 3128 ssl-bump generate-host-certificates=on dynamic_cert_mem_cache_size=4MB cert=/usr/local/squid/certs/SquidCA.pem always_direct allow all ssl_bump server-first all sslcrtd_program /usr/local/squid/libexec/ssl_crtd -s /usr/local/squid/var/lib/ssl_db -M 4MB client_persistent_connections on server_persistent_connections on sslproxy_version 3 sslproxy_options ALL cache_dir aufs /usr/local/squid/var/cache/squid 100 16 256 coredump_dir /usr/local/squid/var/cache/squid strip_query_terms off httpd_suppress_version_string on via off forwarded_for transparent vary_ignore_expire on refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 UPDATE: I have tried compiling squid 3.4.5 with openssl 1.0.1h . No improvements

  Read the article

• VSS Post Backup failures for Virtual Server 2005 R2 SP1 virtual machines

  - by califguy4christ

  We've been seeing strange errors with Volume Shadow Copy services on our Virtual Server 2005 R2 SP1 host. It appears to be failing on a strange mountpoint in the C:\WINDOWS\Temp\ folders, which I believe is used by VSS to mount a writeable image file. To summarize: The Microsoft Virtual Server 2005 Writer continually goes into a failed retryable state The Virtual Server log reports errors during the Post Backup phase VSS reports errors backing up a mount point of unknown origins The mount point causes NTFS and ftdisk errors The host is x86 Windows Server 2003 Standard, SP2. The virtual machine is the same. Both use basic disks. Here is the writer state: Writer name: 'Microsoft Virtual Server 2005 Writer' Writer Id: {76afb926-87ad-4a20-a50f-cdc69412ddfc} Writer Instance Id: {78df98e2-bf19-4804-890b-15865efef3bd} State: [11] Failed Last error: Retryable error From the Virtual Server log: Virtual Server - Vss Writer - Event ID: 1035: The VSS writer for Virtual Server failed during the PostBackup phase. The guest shadow copies did not get exposed on the host machine, after mounting all the virtual hard disks of the virtual machine VMACHINE. From the Application log: VSS - None - Event ID: 12290: Volume Shadow Copy Service warning: GetVolumeInformationW( \\?\Volume{fb84bae7-87f5-11dd-9832-001cc4961ca6}\,NULL,0, NULL,NULL,[0x00000000], , 260) == 0x0000045d. hr = 0x00000000. From the System log: Ntfs - Disk - Event ID: 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:\WINDOWS\Temp\ {fb84bae7-87f5-11dd-9832-001cc49.... My current theory is that VSS creates a mount point for an image file of the VHD, then the software panics for some reason, leaving everything in an inconsistent state. Removing the mount point doesn't resolve the problem. All of the other disks check out fine with CHKDSK. There's no exclusion option for VHDs or to turn off online backups. Has anyone seen this kind of thing before or point me in the right direction for getting more information about the mount point and it's origins? I haven't been able to trace what application is creating that mount point.

  Read the article

• SharePoint 2010 User Profile Synchronization

  - by manemawanna

  Hello, I'm completely new to working with SharePoint and Windows Server, but last week I was given a small brief to play with SharePoint 2010 to see how I got along with it. Anyway I've set up a SharePoint server and had a mess around to get some new sites and pages created etc, but I'm now looking to have a try at importing some AD groups. As part of this I've look at these tutorials, here and here. So far I've got through to the process of starting the User Profile Service which works fine, but when I get it starting the User Profile Synchronization service it sits on starting. But when I refresh the page or go to the monitoring section it shows it as aborted. Now I'm new to administering servers like I say and when I start the User Profile Synchronization service it tries to run as NT AUTHORITY\NETWORK SERVICE and asks for a password so I've been providing it with the admin password, now I'm not sure if this is part of the issue or not as I've checked the log files and they seem to say that it doesn't have permissions, which is fair enough, but I can't see how you can change the account even if I wanted to. So if anyone could help it would be appreciated, if you need any further information to help with an answer, just let me know.

  Read the article

• 8Gb Fiber Channcel HBA vs. 10 Gb SPF+ Converged HBA

  - by Hossein Aarabi

  I am putting a Dell server together, more specifically R720. I have to select the correct Host Bus Adapter. This HBA on R710 will connect to a storage device. I am confused between these two: QLogic 2562, Dual Port 8Gb Optical Fiber Channel HBA (price $2,045) QLogic 8262, Dual Port 10Gb SFP+, Converged Network Adapter (price $1,618) I thought since the QLogic 2562 is a fiber channel and is more expensive then it is faster in terms of IOPS. But, it is a 8Gb as opposed to 10 Gb of SFP+. My questions: Which one is better (IOPS performance, etc.)? Why should I choose one over another?

  Read the article

• Apache Simple Configuration Issue: per-user directory is accessing /~user instead of ~user

  - by Huckphin

  Hello. I am just getting Apache 2.2 running on Fedora 13 Beta 64-bit. I am running into issues setting my per-user directory. The goal is to make localhost/~user map to /home/~user/public_html. I think that I have the permissions right because I have 755 to /home/~user, and I have 755 to /home/~user/public_html/ and I have 777 for all contents inside of /home/~user/public_html/ recursively set. My mod_userdir configuration looks like this: <IfModule mod_userdir.c> # # UserDir is disabled by default since it can confirm the presence # of a username on the system (depending on home directory # permissions). # UserDir disabled root UserDir enabled huckphin # # To enable requests to /~user/ to serve the user's public_html # directory, remove the "UserDir disabled" line above, and uncomment # the following line instead: # UserDir public_html The error that I am seeing in the error log is this: [Sat May 15 09:54:29 2010] [error] [client 127.0.0.1] (13)Permission denied: access to /~huckphin/index.html denied When I login as the apache user, I know that /~huckphin does not exist, and this is not what I want. I want it to be accessing ~huckphin, not /~huckphin. What do I need to change on my configuration for this to work?

  Read the article

• Hive metadata permission issue

  - by Chandramohan

  We are getting this error on Hive, while creating a DB / table hive> CREATE TABLE pokes (foo INT, bar STRING); FAILED: Error in metadata: javax.jdo.JDOFatalDataStoreException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. NestedThrowables: org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. FAILED: Execution Error, return code 1 from org.apache.hadoop.hive.ql.exec.DDLTask Hive log : org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.datanucleus.jdo.NucleusJDOHelper.getJDOExceptionForNucleusException(NucleusJDOHelper.java:298) at org.datanucleus.jdo.JDOPersistenceManagerFactory.freezeConfiguration(JDOPersistenceManagerFactory.java:601) at org.datanucleus.jdo.JDOPersistenceManagerFactory.createPersistenceManagerFactory(JDOPersistenceManagerFactory.java:286) at org.datanucleus.jdo.JDOPersistenceManagerFactory.getPersistenceManagerFactory(JDOPersistenceManagerFactory.java:182) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at javax.jdo.JDOHelper$16.run(JDOHelper.java:1958) at java.security.AccessController.doPrivileged(Native Method) at javax.jdo.JDOHelper.invoke(JDOHelper.java:1953) at javax.jdo.JDOHelper.invokeGetPersistenceManagerFactoryOnImplementation(JDOHelper.java:1159) at javax.jdo.JDOHelper.getPersistenceManagerFactory(JDOHelper.java:803) at javax.jdo.JDOHelper.getPersistenceManagerFactory(JDOHelper.java:698) at org.apache.hadoop.hive.metastore.ObjectStore.getPMF(ObjectStore.java:234) at org.apache.hadoop.hive.metastore.ObjectStore.getPersistenceManager(ObjectStore.java:261) at org.apache.hadoop.hive.metastore.ObjectStore.initialize(ObjectStore.java:196) at org.apache.hadoop.hive.metastore.ObjectStore.setConf(ObjectStore.java:171) at org.apache.hadoop.util.ReflectionUtils.setConf(ReflectionUtils.java:62) at org.apache.hadoop.util.ReflectionUtils.newInstance(ReflectionUtils.java:117) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.getMS(HiveMetaStore.java:354) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.executeWithRetry(HiveMetaStore.java:306) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.createDefaultDB(HiveMetaStore.java:451) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.init(HiveMetaStore.java:232) at org.apache.hadoop.hive.metastore.HiveMetaStore$HMSHandler.<init>(HiveMetaStore.java:197) at org.apache.hadoop.hive.metastore.HiveMetaStoreClient.<init>(HiveMetaStoreClient.java:108) at org.apache.hadoop.hive.ql.metadata.Hive.createMetaStoreClient(Hive.java:1868) at org.apache.hadoop.hive.ql.metadata.Hive.getMSC(Hive.java:1878) at org.apache.hadoop.hive.ql.metadata.Hive.createTable(Hive.java:470) ... 15 more Caused by: org.apache.commons.dbcp.SQLNestedException: Cannot get a connection, pool error Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.apache.commons.dbcp.PoolingDataSource.getConnection(PoolingDataSource.java:114) at org.datanucleus.store.rdbms.ConnectionFactoryImpl$ManagedConnectionImpl.getConnection(ConnectionFactoryImpl.java:521) at org.datanucleus.store.rdbms.RDBMSStoreManager.<init>(RDBMSStoreManager.java:290) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27) at java.lang.reflect.Constructor.newInstance(Constructor.java:513) at org.datanucleus.plugin.NonManagedPluginRegistry.createExecutableExtension(NonManagedPluginRegistry.java:588) at org.datanucleus.plugin.PluginManager.createExecutableExtension(PluginManager.java:300) at org.datanucleus.ObjectManagerFactoryImpl.initialiseStoreManager(ObjectManagerFactoryImpl.java:161) at org.datanucleus.jdo.JDOPersistenceManagerFactory.freezeConfiguration(JDOPersistenceManagerFactory.java:583) ... 42 more Caused by: java.util.NoSuchElementException: Could not create a validated object, cause: A read-only user or a user in a read-only database is not permitted to disable read-only mode on a connection. at org.apache.commons.pool.impl.GenericObjectPool.borrowObject(GenericObjectPool.java:1191) at org.apache.commons.dbcp.PoolingDataSource.getConnection(PoolingDataSource.java:106) ... 52 more 2011-08-11 18:02:36,964 ERROR ql.Driver (SessionState.java:printError(343)) - FAILED: Execution Error, return code 1 from org.apache.hadoop.hive.ql.exec.DDLTask

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >